drivers/spi/spi-omap-uwire.c

   1 /*
   2  * MicroWire interface driver for OMAP
   3  *
   4  * Copyright 2003 MontaVista Software Inc. <source@mvista.com>
   5  *
   6  * Ported to 2.6 OMAP uwire interface.
   7  * Copyright (C) 2004 Texas Instruments.
   8  *
   9  * Generalization patches by Juha Yrjola <juha.yrjola@nokia.com>
  10  *
  11  * Copyright (C) 2005 David Brownell (ported to 2.6 SPI interface)
  12  * Copyright (C) 2006 Nokia
  13  *
  14  * Many updates by Imre Deak <imre.deak@nokia.com>
  15  *
  16  * This program is free software; you can redistribute it and/or modify it
  17  * under the terms of the GNU General Public License as published by the
  18  * Free Software Foundation; either version 2 of the License, or (at your
  19  * option) any later version.
  20  *
  21  * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
  22  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
  23  * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
  24  * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
  25  * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
  26  * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
  27  * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
  28  * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
  29  * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
  30  * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  31  *
  32  * You should have received a copy of the GNU General Public License along
  33  * with this program; if not, write to the Free Software Foundation, Inc.,
  34  * 675 Mass Ave, Cambridge, MA 02139, USA.
  35  */
  36 #include <linux/kernel.h>
  37 #include <linux/init.h>
  38 #include <linux/delay.h>
  39 #include <linux/platform_device.h>
  40 #include <linux/workqueue.h>
  41 #include <linux/interrupt.h>
  42 #include <linux/err.h>
  43 #include <linux/clk.h>
  44 #include <linux/slab.h>
  45
  46 #include <linux/spi/spi.h>
  47 #include <linux/spi/spi_bitbang.h>
  48
  49 #include <asm/system.h>
  50 #include <asm/irq.h>
  51 #include <mach/hardware.h>
  52 #include <asm/io.h>
  53 #include <asm/mach-types.h>
  54
  55 #include <plat/mux.h>
  56 #include <plat/omap7xx.h>       /* OMAP7XX_IO_CONF registers */
  57
  58
  59 /* FIXME address is now a platform device resource,
  60  * and irqs should show there too...
  61  */
  62 #define UWIRE_BASE_PHYS         0xFFFB3000
  63
  64 /* uWire Registers: */
  65 #define UWIRE_IO_SIZE 0x20
  66 #define UWIRE_TDR     0x00
  67 #define UWIRE_RDR     0x00
  68 #define UWIRE_CSR     0x01
  69 #define UWIRE_SR1     0x02
  70 #define UWIRE_SR2     0x03
  71 #define UWIRE_SR3     0x04
  72 #define UWIRE_SR4     0x05
  73 #define UWIRE_SR5     0x06
  74
  75 /* CSR bits */
  76 #define RDRB    (1 << 15)
  77 #define CSRB    (1 << 14)
  78 #define START   (1 << 13)
  79 #define CS_CMD  (1 << 12)
  80
  81 /* SR1 or SR2 bits */
  82 #define UWIRE_READ_FALLING_EDGE         0x0001
  83 #define UWIRE_READ_RISING_EDGE          0x0000
  84 #define UWIRE_WRITE_FALLING_EDGE        0x0000
  85 #define UWIRE_WRITE_RISING_EDGE         0x0002
  86 #define UWIRE_CS_ACTIVE_LOW             0x0000
  87 #define UWIRE_CS_ACTIVE_HIGH            0x0004
  88 #define UWIRE_FREQ_DIV_2                0x0000
  89 #define UWIRE_FREQ_DIV_4                0x0008
  90 #define UWIRE_FREQ_DIV_8                0x0010
  91 #define UWIRE_CHK_READY                 0x0020
  92 #define UWIRE_CLK_INVERTED              0x0040
  93
  94
  95 struct uwire_spi {
  96         struct spi_bitbang      bitbang;
  97         struct clk              *ck;
  98 };
  99
 100 struct uwire_state {
 101         unsigned        bits_per_word;
 102         unsigned        div1_idx;
 103 };
 104
 105 /* REVISIT compile time constant for idx_shift? */
 106 /*
 107  * Or, put it in a structure which is used throughout the driver;
 108  * that avoids having to issue two loads for each bit of static data.
 109  */
 110 static unsigned int uwire_idx_shift;
 111 static void __iomem *uwire_base;
 112
 113 static inline void uwire_write_reg(int idx, u16 val)
 114 {
 115         __raw_writew(val, uwire_base + (idx << uwire_idx_shift));
 116 }
 117
 118 static inline u16 uwire_read_reg(int idx)
 119 {
 120         return __raw_readw(uwire_base + (idx << uwire_idx_shift));
 121 }
 122
 123 static inline void omap_uwire_configure_mode(u8 cs, unsigned long flags)
 124 {
 125         u16     w, val = 0;
 126         int     shift, reg;
 127
 128         if (flags & UWIRE_CLK_INVERTED)
 129                 val ^= 0x03;
 130         val = flags & 0x3f;
 131         if (cs & 1)
 132                 shift = 6;
 133         else
 134                 shift = 0;
 135         if (cs <= 1)
 136                 reg = UWIRE_SR1;
 137         else
 138                 reg = UWIRE_SR2;
 139
 140         w = uwire_read_reg(reg);
 141         w &= ~(0x3f << shift);
 142         w |= val << shift;
 143         uwire_write_reg(reg, w);
 144 }
 145
 146 static int wait_uwire_csr_flag(u16 mask, u16 val, int might_not_catch)
 147 {
 148         u16 w;
 149         int c = 0;
 150         unsigned long max_jiffies = jiffies + HZ;
 151
 152         for (;;) {
 153                 w = uwire_read_reg(UWIRE_CSR);
 154                 if ((w & mask) == val)
 155                         break;
 156                 if (time_after(jiffies, max_jiffies)) {
 157                         printk(KERN_ERR "%s: timeout. reg=%#06x "
 158                                         "mask=%#06x val=%#06x\n",
 159                                __func__, w, mask, val);
 160                         return -1;
 161                 }
 162                 c++;
 163                 if (might_not_catch && c > 64)
 164                         break;
 165         }
 166         return 0;
 167 }
 168
 169 static void uwire_set_clk1_div(int div1_idx)
 170 {
 171         u16 w;
 172
 173         w = uwire_read_reg(UWIRE_SR3);
 174         w &= ~(0x03 << 1);
 175         w |= div1_idx << 1;
 176         uwire_write_reg(UWIRE_SR3, w);
 177 }
 178
 179 static void uwire_chipselect(struct spi_device *spi, int value)
 180 {
 181         struct  uwire_state *ust = spi->controller_state;
 182         u16     w;
 183         int     old_cs;
 184
 185
 186         BUG_ON(wait_uwire_csr_flag(CSRB, 0, 0));
 187
 188         w = uwire_read_reg(UWIRE_CSR);
 189         old_cs = (w >> 10) & 0x03;
 190         if (value == BITBANG_CS_INACTIVE || old_cs != spi->chip_select) {
 191                 /* Deselect this CS, or the previous CS */
 192                 w &= ~CS_CMD;
 193                 uwire_write_reg(UWIRE_CSR, w);
 194         }
 195         /* activate specfied chipselect */
 196         if (value == BITBANG_CS_ACTIVE) {
 197                 uwire_set_clk1_div(ust->div1_idx);
 198                 /* invert clock? */
 199                 if (spi->mode & SPI_CPOL)
 200                         uwire_write_reg(UWIRE_SR4, 1);
 201                 else
 202                         uwire_write_reg(UWIRE_SR4, 0);
 203
 204                 w = spi->chip_select << 10;
 205                 w |= CS_CMD;
 206                 uwire_write_reg(UWIRE_CSR, w);
 207         }
 208 }
 209
 210 static int uwire_txrx(struct spi_device *spi, struct spi_transfer *t)
 211 {
 212         struct uwire_state *ust = spi->controller_state;
 213         unsigned        len = t->len;
 214         unsigned        bits = ust->bits_per_word;
 215         unsigned        bytes;
 216         u16             val, w;
 217         int             status = 0;
 218
 219         if (!t->tx_buf && !t->rx_buf)
 220                 return 0;
 221
 222         /* Microwire doesn't read and write concurrently */
 223         if (t->tx_buf && t->rx_buf)
 224                 return -EPERM;
 225
 226         w = spi->chip_select << 10;
 227         w |= CS_CMD;
 228
 229         if (t->tx_buf) {
 230                 const u8        *buf = t->tx_buf;
 231
 232                 /* NOTE:  DMA could be used for TX transfers */
 233
 234                 /* write one or two bytes at a time */
 235                 while (len >= 1) {
 236                         /* tx bit 15 is first sent; we byteswap multibyte words
 237                          * (msb-first) on the way out from memory.
 238                          */
 239                         val = *buf++;
 240                         if (bits > 8) {
 241                                 bytes = 2;
 242                                 val |= *buf++ << 8;
 243                         } else
 244                                 bytes = 1;
 245                         val <<= 16 - bits;
 246
 247 #ifdef  VERBOSE
 248                         pr_debug("%s: write-%d =%04x\n",
 249                                         dev_name(&spi->dev), bits, val);
 250 #endif
 251                         if (wait_uwire_csr_flag(CSRB, 0, 0))
 252                                 goto eio;
 253
 254                         uwire_write_reg(UWIRE_TDR, val);
 255
 256                         /* start write */
 257                         val = START | w | (bits << 5);
 258
 259                         uwire_write_reg(UWIRE_CSR, val);
 260                         len -= bytes;
 261
 262                         /* Wait till write actually starts.
 263                          * This is needed with MPU clock 60+ MHz.
 264                          * REVISIT: we may not have time to catch it...
 265                          */
 266                         if (wait_uwire_csr_flag(CSRB, CSRB, 1))
 267                                 goto eio;
 268
 269                         status += bytes;
 270                 }
 271
 272                 /* REVISIT:  save this for later to get more i/o overlap */
 273                 if (wait_uwire_csr_flag(CSRB, 0, 0))
 274                         goto eio;
 275
 276         } else if (t->rx_buf) {
 277                 u8              *buf = t->rx_buf;
 278
 279                 /* read one or two bytes at a time */
 280                 while (len) {
 281                         if (bits > 8) {
 282                                 bytes = 2;
 283                         } else
 284                                 bytes = 1;
 285
 286                         /* start read */
 287                         val = START | w | (bits << 0);
 288                         uwire_write_reg(UWIRE_CSR, val);
 289                         len -= bytes;
 290
 291                         /* Wait till read actually starts */
 292                         (void) wait_uwire_csr_flag(CSRB, CSRB, 1);
 293
 294                         if (wait_uwire_csr_flag(RDRB | CSRB,
 295                                                 RDRB, 0))
 296                                 goto eio;
 297
 298                         /* rx bit 0 is last received; multibyte words will
 299                          * be properly byteswapped on the way to memory.
 300                          */
 301                         val = uwire_read_reg(UWIRE_RDR);
 302                         val &= (1 << bits) - 1;
 303                         *buf++ = (u8) val;
 304                         if (bytes == 2)
 305                                 *buf++ = val >> 8;
 306                         status += bytes;
 307 #ifdef  VERBOSE
 308                         pr_debug("%s: read-%d =%04x\n",
 309                                         dev_name(&spi->dev), bits, val);
 310 #endif
 311
 312                 }
 313         }
 314         return status;
 315 eio:
 316         return -EIO;
 317 }
 318
 319 static int uwire_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
 320 {
 321         struct uwire_state      *ust = spi->controller_state;
 322         struct uwire_spi        *uwire;
 323         unsigned                flags = 0;
 324         unsigned                bits;
 325         unsigned                hz;
 326         unsigned long           rate;
 327         int                     div1_idx;
 328         int                     div1;
 329         int                     div2;
 330         int                     status;
 331
 332         uwire = spi_master_get_devdata(spi->master);
 333
 334         if (spi->chip_select > 3) {
 335                 pr_debug("%s: cs%d?\n", dev_name(&spi->dev), spi->chip_select);
 336                 status = -ENODEV;
 337                 goto done;
 338         }
 339
 340         bits = spi->bits_per_word;
 341         if (t != NULL && t->bits_per_word)
 342                 bits = t->bits_per_word;
 343
 344         if (bits > 16) {
 345                 pr_debug("%s: wordsize %d?\n", dev_name(&spi->dev), bits);
 346                 status = -ENODEV;
 347                 goto done;
 348         }
 349         ust->bits_per_word = bits;
 350
 351         /* mode 0..3, clock inverted separately;
 352          * standard nCS signaling;
 353          * don't treat DI=high as "not ready"
 354          */
 355         if (spi->mode & SPI_CS_HIGH)
 356                 flags |= UWIRE_CS_ACTIVE_HIGH;
 357
 358         if (spi->mode & SPI_CPOL)
 359                 flags |= UWIRE_CLK_INVERTED;
 360
 361         switch (spi->mode & (SPI_CPOL | SPI_CPHA)) {
 362         case SPI_MODE_0:
 363         case SPI_MODE_3:
 364                 flags |= UWIRE_WRITE_FALLING_EDGE | UWIRE_READ_RISING_EDGE;
 365                 break;
 366         case SPI_MODE_1:
 367         case SPI_MODE_2:
 368                 flags |= UWIRE_WRITE_RISING_EDGE | UWIRE_READ_FALLING_EDGE;
 369                 break;
 370         }
 371
 372         /* assume it's already enabled */
 373         rate = clk_get_rate(uwire->ck);
 374
 375         hz = spi->max_speed_hz;
 376         if (t != NULL && t->speed_hz)
 377                 hz = t->speed_hz;
 378
 379         if (!hz) {
 380                 pr_debug("%s: zero speed?\n", dev_name(&spi->dev));
 381                 status = -EINVAL;
 382                 goto done;
 383         }
 384
 385         /* F_INT = mpu_xor_clk / DIV1 */
 386         for (div1_idx = 0; div1_idx < 4; div1_idx++) {
 387                 switch (div1_idx) {
 388                 case 0:
 389                         div1 = 2;
 390                         break;
 391                 case 1:
 392                         div1 = 4;
 393                         break;
 394                 case 2:
 395                         div1 = 7;
 396                         break;
 397                 default:
 398                 case 3:
 399                         div1 = 10;
 400                         break;
 401                 }
 402                 div2 = (rate / div1 + hz - 1) / hz;
 403                 if (div2 <= 8)
 404                         break;
 405         }
 406         if (div1_idx == 4) {
 407                 pr_debug("%s: lowest clock %ld, need %d\n",
 408                         dev_name(&spi->dev), rate / 10 / 8, hz);
 409                 status = -EDOM;
 410                 goto done;
 411         }
 412
 413         /* we have to cache this and reset in uwire_chipselect as this is a
 414          * global parameter and another uwire device can change it under
 415          * us */
 416         ust->div1_idx = div1_idx;
 417         uwire_set_clk1_div(div1_idx);
 418
 419         rate /= div1;
 420
 421         switch (div2) {
 422         case 0:
 423         case 1:
 424         case 2:
 425                 flags |= UWIRE_FREQ_DIV_2;
 426                 rate /= 2;
 427                 break;
 428         case 3:
 429         case 4:
 430                 flags |= UWIRE_FREQ_DIV_4;
 431                 rate /= 4;
 432                 break;
 433         case 5:
 434         case 6:
 435         case 7:
 436         case 8:
 437                 flags |= UWIRE_FREQ_DIV_8;
 438                 rate /= 8;
 439                 break;
 440         }
 441         omap_uwire_configure_mode(spi->chip_select, flags);
 442         pr_debug("%s: uwire flags %02x, armxor %lu KHz, SCK %lu KHz\n",
 443                         __func__, flags,
 444                         clk_get_rate(uwire->ck) / 1000,
 445                         rate / 1000);
 446         status = 0;
 447 done:
 448         return status;
 449 }
 450
 451 static int uwire_setup(struct spi_device *spi)
 452 {
 453         struct uwire_state *ust = spi->controller_state;
 454
 455         if (ust == NULL) {
 456                 ust = kzalloc(sizeof(*ust), GFP_KERNEL);
 457                 if (ust == NULL)
 458                         return -ENOMEM;
 459                 spi->controller_state = ust;
 460         }
 461
 462         return uwire_setup_transfer(spi, NULL);
 463 }
 464
 465 static void uwire_cleanup(struct spi_device *spi)
 466 {
 467         kfree(spi->controller_state);
 468 }
 469
 470 static void uwire_off(struct uwire_spi *uwire)
 471 {
 472         uwire_write_reg(UWIRE_SR3, 0);
 473         clk_disable(uwire->ck);
 474         clk_put(uwire->ck);
 475         spi_master_put(uwire->bitbang.master);
 476 }
 477
 478 static int __init uwire_probe(struct platform_device *pdev)
 479 {
 480         struct spi_master       *master;
 481         struct uwire_spi        *uwire;
 482         int                     status;
 483
 484         master = spi_alloc_master(&pdev->dev, sizeof *uwire);
 485         if (!master)
 486                 return -ENODEV;
 487
 488         uwire = spi_master_get_devdata(master);
 489
 490         uwire_base = ioremap(UWIRE_BASE_PHYS, UWIRE_IO_SIZE);
 491         if (!uwire_base) {
 492                 dev_dbg(&pdev->dev, "can't ioremap UWIRE\n");
 493                 spi_master_put(master);
 494                 return -ENOMEM;
 495         }
 496
 497         dev_set_drvdata(&pdev->dev, uwire);
 498
 499         uwire->ck = clk_get(&pdev->dev, "fck");
 500         if (IS_ERR(uwire->ck)) {
 501                 status = PTR_ERR(uwire->ck);
 502                 dev_dbg(&pdev->dev, "no functional clock?\n");
 503                 spi_master_put(master);
 504                 return status;
 505         }
 506         clk_enable(uwire->ck);
 507
 508         if (cpu_is_omap7xx())
 509                 uwire_idx_shift = 1;
 510         else
 511                 uwire_idx_shift = 2;
 512
 513         uwire_write_reg(UWIRE_SR3, 1);
 514
 515         /* the spi->mode bits understood by this driver: */
 516         master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 517
 518         master->flags = SPI_MASTER_HALF_DUPLEX;
 519
 520         master->bus_num = 2;    /* "official" */
 521         master->num_chipselect = 4;
 522         master->setup = uwire_setup;
 523         master->cleanup = uwire_cleanup;
 524
 525         uwire->bitbang.master = master;
 526         uwire->bitbang.chipselect = uwire_chipselect;
 527         uwire->bitbang.setup_transfer = uwire_setup_transfer;
 528         uwire->bitbang.txrx_bufs = uwire_txrx;
 529
 530         status = spi_bitbang_start(&uwire->bitbang);
 531         if (status < 0) {
 532                 uwire_off(uwire);
 533                 iounmap(uwire_base);
 534         }
 535         return status;
 536 }
 537
 538 static int __exit uwire_remove(struct platform_device *pdev)
 539 {
 540         struct uwire_spi        *uwire = dev_get_drvdata(&pdev->dev);
 541         int                     status;
 542
 543         // FIXME remove all child devices, somewhere ...
 544
 545         status = spi_bitbang_stop(&uwire->bitbang);
 546         uwire_off(uwire);
 547         iounmap(uwire_base);
 548         return status;
 549 }
 550
 551 /* work with hotplug and coldplug */
 552 MODULE_ALIAS("platform:omap_uwire");
 553
 554 static struct platform_driver uwire_driver = {
 555         .driver = {
 556                 .name           = "omap_uwire",
 557                 .owner          = THIS_MODULE,
 558         },
 559         .remove         = __exit_p(uwire_remove),
 560         // suspend ... unuse ck
 561         // resume ... use ck
 562 };
 563
 564 static int __init omap_uwire_init(void)
 565 {
 566         /* FIXME move these into the relevant board init code. also, include
 567          * H3 support; it uses tsc2101 like H2 (on a different chipselect).
 568          */
 569
 570         if (machine_is_omap_h2()) {
 571                 /* defaults: W21 SDO, U18 SDI, V19 SCL */
 572                 omap_cfg_reg(N14_1610_UWIRE_CS0);
 573                 omap_cfg_reg(N15_1610_UWIRE_CS1);
 574         }
 575         if (machine_is_omap_perseus2()) {
 576                 /* configure pins: MPU_UW_nSCS1, MPU_UW_SDO, MPU_UW_SCLK */
 577                 int val = omap_readl(OMAP7XX_IO_CONF_9) & ~0x00EEE000;
 578                 omap_writel(val | 0x00AAA000, OMAP7XX_IO_CONF_9);
 579         }
 580
 581         return platform_driver_probe(&uwire_driver, uwire_probe);
 582 }
 583
 584 static void __exit omap_uwire_exit(void)
 585 {
 586         platform_driver_unregister(&uwire_driver);
 587 }
 588
 589 subsys_initcall(omap_uwire_init);
 590 module_exit(omap_uwire_exit);
 591
 592 MODULE_LICENSE("GPL");
 593