drivers/ata/pata_mpiix.c

   1 /*
   2  * pata_mpiix.c         - Intel MPIIX PATA for new ATA layer
   3  *                        (C) 2005-2006 Red Hat Inc
   4  *                        Alan Cox <alan@lxorguk.ukuu.org.uk>
   5  *
   6  * The MPIIX is different enough to the PIIX4 and friends that we give it
   7  * a separate driver. The old ide/pci code handles this by just not tuning
   8  * MPIIX at all.
   9  *
  10  * The MPIIX also differs in another important way from the majority of PIIX
  11  * devices. The chip is a bridge (pardon the pun) between the old world of
  12  * ISA IDE and PCI IDE. Although the ATA timings are PCI configured the actual
  13  * IDE controller is not decoded in PCI space and the chip does not claim to
  14  * be IDE class PCI. This requires slightly non-standard probe logic compared
  15  * with PCI IDE and also that we do not disable the device when our driver is
  16  * unloaded (as it has many other functions).
  17  *
  18  * The driver consciously keeps this logic internally to avoid pushing quirky
  19  * PATA history into the clean libata layer.
  20  *
  21  * Thinkpad specific note: If you boot an MPIIX using a thinkpad with a PCMCIA
  22  * hard disk present this driver will not detect it. This is not a bug. In this
  23  * configuration the secondary port of the MPIIX is disabled and the addresses
  24  * are decoded by the PCMCIA bridge and therefore are for a generic IDE driver
  25  * to operate.
  26  */
  27
  28 #include <linux/kernel.h>
  29 #include <linux/module.h>
  30 #include <linux/pci.h>
  31 #include <linux/init.h>
  32 #include <linux/blkdev.h>
  33 #include <linux/delay.h>
  34 #include <scsi/scsi_host.h>
  35 #include <linux/libata.h>
  36
  37 #define DRV_NAME "pata_mpiix"
  38 #define DRV_VERSION "0.7.7"
  39
  40 enum {
  41         IDETIM = 0x6C,          /* IDE control register */
  42         IORDY = (1 << 1),
  43         PPE = (1 << 2),
  44         FTIM = (1 << 0),
  45         ENABLED = (1 << 15),
  46         SECONDARY = (1 << 14)
  47 };
  48
  49 static int mpiix_pre_reset(struct ata_link *link, unsigned long deadline)
  50 {
  51         struct ata_port *ap = link->ap;
  52         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  53         static const struct pci_bits mpiix_enable_bits = { 0x6D, 1, 0x80, 0x80 };
  54
  55         if (!pci_test_config_bits(pdev, &mpiix_enable_bits))
  56                 return -ENOENT;
  57
  58         return ata_sff_prereset(link, deadline);
  59 }
  60
  61 /**
  62  *      mpiix_set_piomode       -       set initial PIO mode data
  63  *      @ap: ATA interface
  64  *      @adev: ATA device
  65  *
  66  *      Called to do the PIO mode setup. The MPIIX allows us to program the
  67  *      IORDY sample point (2-5 clocks), recovery (1-4 clocks) and whether
  68  *      prefetching or IORDY are used.
  69  *
  70  *      This would get very ugly because we can only program timing for one
  71  *      device at a time, the other gets PIO0. Fortunately libata calls
  72  *      our qc_issue command before a command is issued so we can flip the
  73  *      timings back and forth to reduce the pain.
  74  */
  75
  76 static void mpiix_set_piomode(struct ata_port *ap, struct ata_device *adev)
  77 {
  78         int control = 0;
  79         int pio = adev->pio_mode - XFER_PIO_0;
  80         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  81         u16 idetim;
  82         static const     /* ISP  RTC */
  83         u8 timings[][2] = { { 0, 0 },
  84                             { 0, 0 },
  85                             { 1, 0 },
  86                             { 2, 1 },
  87                             { 2, 3 }, };
  88
  89         pci_read_config_word(pdev, IDETIM, &idetim);
  90
  91         /* Mask the IORDY/TIME/PPE for this device */
  92         if (adev->class == ATA_DEV_ATA)
  93                 control |= PPE;         /* Enable prefetch/posting for disk */
  94         if (ata_pio_need_iordy(adev))
  95                 control |= IORDY;
  96         if (pio > 1)
  97                 control |= FTIM;        /* This drive is on the fast timing bank */
  98
  99         /* Mask out timing and clear both TIME bank selects */
 100         idetim &= 0xCCEE;
 101         idetim &= ~(0x07  << (4 * adev->devno));
 102         idetim |= control << (4 * adev->devno);
 103
 104         idetim |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
 105         pci_write_config_word(pdev, IDETIM, idetim);
 106
 107         /* We use ap->private_data as a pointer to the device currently
 108            loaded for timing */
 109         ap->private_data = adev;
 110 }
 111
 112 /**
 113  *      mpiix_qc_issue          -       command issue
 114  *      @qc: command pending
 115  *
 116  *      Called when the libata layer is about to issue a command. We wrap
 117  *      this interface so that we can load the correct ATA timings if
 118  *      necessary. Our logic also clears TIME0/TIME1 for the other device so
 119  *      that, even if we get this wrong, cycles to the other device will
 120  *      be made PIO0.
 121  */
 122
 123 static unsigned int mpiix_qc_issue(struct ata_queued_cmd *qc)
 124 {
 125         struct ata_port *ap = qc->ap;
 126         struct ata_device *adev = qc->dev;
 127
 128         /* If modes have been configured and the channel data is not loaded
 129            then load it. We have to check if pio_mode is set as the core code
 130            does not set adev->pio_mode to XFER_PIO_0 while probing as would be
 131            logical */
 132
 133         if (adev->pio_mode && adev != ap->private_data)
 134                 mpiix_set_piomode(ap, adev);
 135
 136         return ata_sff_qc_issue(qc);
 137 }
 138
 139 static struct scsi_host_template mpiix_sht = {
 140         ATA_PIO_SHT(DRV_NAME),
 141 };
 142
 143 static struct ata_port_operations mpiix_port_ops = {
 144         .inherits       = &ata_sff_port_ops,
 145         .qc_issue       = mpiix_qc_issue,
 146         .cable_detect   = ata_cable_40wire,
 147         .set_piomode    = mpiix_set_piomode,
 148         .prereset       = mpiix_pre_reset,
 149         .sff_data_xfer  = ata_sff_data_xfer32,
 150 };
 151
 152 static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 153 {
 154         /* Single threaded by the PCI probe logic */
 155         static int printed_version;
 156         struct ata_host *host;
 157         struct ata_port *ap;
 158         void __iomem *cmd_addr, *ctl_addr;
 159         u16 idetim;
 160         int cmd, ctl, irq;
 161
 162         if (!printed_version++)
 163                 dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
 164
 165         host = ata_host_alloc(&dev->dev, 1);
 166         if (!host)
 167                 return -ENOMEM;
 168         ap = host->ports[0];
 169
 170         /* MPIIX has many functions which can be turned on or off according
 171            to other devices present. Make sure IDE is enabled before we try
 172            and use it */
 173
 174         pci_read_config_word(dev, IDETIM, &idetim);
 175         if (!(idetim & ENABLED))
 176                 return -ENODEV;
 177
 178         /* See if it's primary or secondary channel... */
 179         if (!(idetim & SECONDARY)) {
 180                 cmd = 0x1F0;
 181                 ctl = 0x3F6;
 182                 irq = 14;
 183         } else {
 184                 cmd = 0x170;
 185                 ctl = 0x376;
 186                 irq = 15;
 187         }
 188
 189         cmd_addr = devm_ioport_map(&dev->dev, cmd, 8);
 190         ctl_addr = devm_ioport_map(&dev->dev, ctl, 1);
 191         if (!cmd_addr || !ctl_addr)
 192                 return -ENOMEM;
 193
 194         ata_port_desc(ap, "cmd 0x%x ctl 0x%x", cmd, ctl);
 195
 196         /* We do our own plumbing to avoid leaking special cases for whacko
 197            ancient hardware into the core code. There are two issues to
 198            worry about.  #1 The chip is a bridge so if in legacy mode and
 199            without BARs set fools the setup.  #2 If you pci_disable_device
 200            the MPIIX your box goes castors up */
 201
 202         ap->ops = &mpiix_port_ops;
 203         ap->pio_mask = ATA_PIO4;
 204         ap->flags |= ATA_FLAG_SLAVE_POSS;
 205
 206         ap->ioaddr.cmd_addr = cmd_addr;
 207         ap->ioaddr.ctl_addr = ctl_addr;
 208         ap->ioaddr.altstatus_addr = ctl_addr;
 209
 210         /* Let libata fill in the port details */
 211         ata_sff_std_ports(&ap->ioaddr);
 212
 213         /* activate host */
 214         return ata_host_activate(host, irq, ata_sff_interrupt, IRQF_SHARED,
 215                                  &mpiix_sht);
 216 }
 217
 218 static const struct pci_device_id mpiix[] = {
 219         { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX), },
 220
 221         { },
 222 };
 223
 224 static struct pci_driver mpiix_pci_driver = {
 225         .name           = DRV_NAME,
 226         .id_table       = mpiix,
 227         .probe          = mpiix_init_one,
 228         .remove         = ata_pci_remove_one,
 229 #ifdef CONFIG_PM
 230         .suspend        = ata_pci_device_suspend,
 231         .resume         = ata_pci_device_resume,
 232 #endif
 233 };
 234
 235 static int __init mpiix_init(void)
 236 {
 237         return pci_register_driver(&mpiix_pci_driver);
 238 }
 239
 240 static void __exit mpiix_exit(void)
 241 {
 242         pci_unregister_driver(&mpiix_pci_driver);
 243 }
 244
 245 MODULE_AUTHOR("Alan Cox");
 246 MODULE_DESCRIPTION("low-level driver for Intel MPIIX");
 247 MODULE_LICENSE("GPL");
 248 MODULE_DEVICE_TABLE(pci, mpiix);
 249 MODULE_VERSION(DRV_VERSION);
 250
 251 module_init(mpiix_init);
 252 module_exit(mpiix_exit);