drivers/net/appletalk/ltpc.c

   1 /***    ltpc.c -- a driver for the LocalTalk PC card.
   2  *
   3  *      Copyright (c) 1995,1996 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
   4  *
   5  *      This software may be used and distributed according to the terms
   6  *      of the GNU General Public License, incorporated herein by reference.
   7  *
   8  *      This is ALPHA code at best.  It may not work for you.  It may
   9  *      damage your equipment.  It may damage your relations with other
  10  *      users of your network.  Use it at your own risk!
  11  *
  12  *      Based in part on:
  13  *      skeleton.c      by Donald Becker
  14  *      dummy.c         by Nick Holloway and Alan Cox
  15  *      loopback.c      by Ross Biro, Fred van Kampen, Donald Becker
  16  *      the netatalk source code (UMICH)
  17  *      lots of work on the card...
  18  *
  19  *      I do not have access to the (proprietary) SDK that goes with the card.
  20  *      If you do, I don't want to know about it, and you can probably write
  21  *      a better driver yourself anyway.  This does mean that the pieces that
  22  *      talk to the card are guesswork on my part, so use at your own risk!
  23  *
  24  *      This is my first try at writing Linux networking code, and is also
  25  *      guesswork.  Again, use at your own risk!  (Although on this part, I'd
  26  *      welcome suggestions)
  27  *
  28  *      This is a loadable kernel module which seems to work at my site
  29  *      consisting of a 1.2.13 linux box running netatalk 1.3.3, and with
  30  *      the kernel support from 1.3.3b2 including patches routing.patch
  31  *      and ddp.disappears.from.chooser.  In order to run it, you will need
  32  *      to patch ddp.c and aarp.c in the kernel, but only a little...
  33  *
  34  *      I'm fairly confident that while this is arguably badly written, the
  35  *      problems that people experience will be "higher level", that is, with
  36  *      complications in the netatalk code.  The driver itself doesn't do
  37  *      anything terribly complicated -- it pretends to be an ether device
  38  *      as far as netatalk is concerned, strips the DDP data out of the ether
  39  *      frame and builds a LLAP packet to send out the card.  In the other
  40  *      direction, it receives LLAP frames from the card and builds a fake
  41  *      ether packet that it then tosses up to the networking code.  You can
  42  *      argue (correctly) that this is an ugly way to do things, but it
  43  *      requires a minimal amount of fooling with the code in ddp.c and aarp.c.
  44  *
  45  *      The card will do a lot more than is used here -- I *think* it has the
  46  *      layers up through ATP.  Even if you knew how that part works (which I
  47  *      don't) it would be a big job to carve up the kernel ddp code to insert
  48  *      things at a higher level, and probably a bad idea...
  49  *
  50  *      There are a number of other cards that do LocalTalk on the PC.  If
  51  *      nobody finds any insurmountable (at the netatalk level) problems
  52  *      here, this driver should encourage people to put some work into the
  53  *      other cards (some of which I gather are still commercially available)
  54  *      and also to put hooks for LocalTalk into the official ddp code.
  55  *
  56  *      I welcome comments and suggestions.  This is my first try at Linux
  57  *      networking stuff, and there are probably lots of things that I did
  58  *      suboptimally.
  59  *
  60  ***/
  61
  62 /***
  63  *
  64  * $Log: ltpc.c,v $
  65  * Revision 1.1.2.1  2000/03/01 05:35:07  jgarzik
  66  * at and tr cleanup
  67  *
  68  * Revision 1.8  1997/01/28 05:44:54  bradford
  69  * Clean up for non-module a little.
  70  * Hacked about a bit to clean things up - Alan Cox
  71  * Probably broken it from the origina 1.8
  72  *
  73
  74  * 1998/11/09: David Huggins-Daines <dhd@debian.org>
  75  * Cleaned up the initialization code to use the standard autoirq methods,
  76    and to probe for things in the standard order of i/o, irq, dma.  This
  77    removes the "reset the reset" hack, because I couldn't figure out an
  78    easy way to get the card to trigger an interrupt after it.
  79  * Added support for passing configuration parameters on the kernel command
  80    line and through insmod
  81  * Changed the device name from "ltalk0" to "lt0", both to conform with the
  82    other localtalk driver, and to clear up the inconsistency between the
  83    module and the non-module versions of the driver :-)
  84  * Added a bunch of comments (I was going to make some enums for the state
  85    codes and the register offsets, but I'm still not sure exactly what their
  86    semantics are)
  87  * Don't poll anymore in interrupt-driven mode
  88  * It seems to work as a module now (as of 2.1.127), but I don't think
  89    I'm responsible for that...
  90
  91  *
  92  * Revision 1.7  1996/12/12 03:42:33  bradford
  93  * DMA alloc cribbed from 3c505.c.
  94  *
  95  * Revision 1.6  1996/12/12 03:18:58  bradford
  96  * Added virt_to_bus; works in 2.1.13.
  97  *
  98  * Revision 1.5  1996/12/12 03:13:22  root
  99  * xmitQel initialization -- think through better though.
 100  *
 101  * Revision 1.4  1996/06/18 14:55:55  root
 102  * Change names to ltpc. Tabs. Took a shot at dma alloc,
 103  * although more needs to be done eventually.
 104  *
 105  * Revision 1.3  1996/05/22 14:59:39  root
 106  * Change dev->open, dev->close to track dummy.c in 1.99.(around 7)
 107  *
 108  * Revision 1.2  1996/05/22 14:58:24  root
 109  * Change tabs mostly.
 110  *
 111  * Revision 1.1  1996/04/23 04:45:09  root
 112  * Initial revision
 113  *
 114  * Revision 0.16  1996/03/05 15:59:56  root
 115  * Change ARPHRD_LOCALTLK definition to the "real" one.
 116  *
 117  * Revision 0.15  1996/03/05 06:28:30  root
 118  * Changes for kernel 1.3.70.  Still need a few patches to kernel, but
 119  * it's getting closer.
 120  *
 121  * Revision 0.14  1996/02/25 17:38:32  root
 122  * More cleanups.  Removed query to card on get_stats.
 123  *
 124  * Revision 0.13  1996/02/21  16:27:40  root
 125  * Refix debug_print_skb.  Fix mac.raw gotcha that appeared in 1.3.65.
 126  * Clean up receive code a little.
 127  *
 128  * Revision 0.12  1996/02/19  16:34:53  root
 129  * Fix debug_print_skb.  Kludge outgoing snet to 0 when using startup
 130  * range.  Change debug to mask: 1 for verbose, 2 for higher level stuff
 131  * including packet printing, 4 for lower level (card i/o) stuff.
 132  *
 133  * Revision 0.11  1996/02/12  15:53:38  root
 134  * Added router sends (requires new aarp.c patch)
 135  *
 136  * Revision 0.10  1996/02/11  00:19:35  root
 137  * Change source LTALK_LOGGING debug switch to insmod ... debug=2.
 138  *
 139  * Revision 0.9  1996/02/10  23:59:35  root
 140  * Fixed those fixes for 1.2 -- DANGER!  The at.h that comes with netatalk
 141  * has a *different* definition of struct sockaddr_at than the Linux kernel
 142  * does.  This is an "insidious and invidious" bug...
 143  * (Actually the preceding comment is false -- it's the atalk.h in the
 144  * ancient atalk-0.06 that's the problem)
 145  *
 146  * Revision 0.8  1996/02/10 19:09:00  root
 147  * Merge 1.3 changes.  Tested OK under 1.3.60.
 148  *
 149  * Revision 0.7  1996/02/10 17:56:56  root
 150  * Added debug=1 parameter on insmod for debugging prints.  Tried
 151  * to fix timer unload on rmmod, but I don't think that's the problem.
 152  *
 153  * Revision 0.6  1995/12/31  19:01:09  root
 154  * Clean up rmmod, irq comments per feedback from Corin Anderson (Thanks Corey!)
 155  * Clean up initial probing -- sometimes the card wakes up latched in reset.
 156  *
 157  * Revision 0.5  1995/12/22  06:03:44  root
 158  * Added comments in front and cleaned up a bit.
 159  * This version sent out to people.
 160  *
 161  * Revision 0.4  1995/12/18  03:46:44  root
 162  * Return shortDDP to longDDP fake to 0/0.  Added command structs.
 163  *
 164  ***/
 165
 166 /* ltpc jumpers are:
 167 *
 168 *       Interrupts -- set at most one.  If none are set, the driver uses
 169 *       polled mode.  Because the card was developed in the XT era, the
 170 *       original documentation refers to IRQ2.  Since you'll be running
 171 *       this on an AT (or later) class machine, that really means IRQ9.
 172 *
 173 *       SW1     IRQ 4
 174 *       SW2     IRQ 3
 175 *       SW3     IRQ 9 (2 in original card documentation only applies to XT)
 176 *
 177 *
 178 *       DMA -- choose DMA 1 or 3, and set both corresponding switches.
 179 *
 180 *       SW4     DMA 3
 181 *       SW5     DMA 1
 182 *       SW6     DMA 3
 183 *       SW7     DMA 1
 184 *
 185 *
 186 *       I/O address -- choose one.
 187 *
 188 *       SW8     220 / 240
 189 */
 190
 191 /*      To have some stuff logged, do
 192 *       insmod ltpc.o debug=1
 193 *
 194 *       For a whole bunch of stuff, use higher numbers.
 195 *
 196 *       The default is 0, i.e. no messages except for the probe results.
 197 */
 198
 199 /* insmod-tweakable variables */
 200 static int debug;
 201 #define DEBUG_VERBOSE 1
 202 #define DEBUG_UPPER 2
 203 #define DEBUG_LOWER 4
 204
 205 static int io;
 206 static int irq;
 207 static int dma;
 208
 209 #include <linux/module.h>
 210 #include <linux/kernel.h>
 211 #include <linux/types.h>
 212 #include <linux/fcntl.h>
 213 #include <linux/interrupt.h>
 214 #include <linux/ptrace.h>
 215 #include <linux/ioport.h>
 216 #include <linux/spinlock.h>
 217 #include <linux/in.h>
 218 #include <linux/slab.h>
 219 #include <linux/string.h>
 220 #include <linux/errno.h>
 221 #include <linux/init.h>
 222 #include <linux/netdevice.h>
 223 #include <linux/etherdevice.h>
 224 #include <linux/skbuff.h>
 225 #include <linux/if_arp.h>
 226 #include <linux/if_ltalk.h>
 227 #include <linux/delay.h>
 228 #include <linux/timer.h>
 229 #include <linux/atalk.h>
 230 #include <linux/bitops.h>
 231
 232 #include <asm/system.h>
 233 #include <asm/dma.h>
 234 #include <asm/io.h>
 235
 236 /* our stuff */
 237 #include "ltpc.h"
 238
 239 static DEFINE_SPINLOCK(txqueue_lock);
 240 static DEFINE_SPINLOCK(mbox_lock);
 241
 242 /* function prototypes */
 243 static int do_read(struct net_device *dev, void *cbuf, int cbuflen,
 244         void *dbuf, int dbuflen);
 245 static int sendup_buffer (struct net_device *dev);
 246
 247 /* Dma Memory related stuff, cribbed directly from 3c505.c */
 248
 249 static unsigned long dma_mem_alloc(int size)
 250 {
 251         int order = get_order(size);
 252
 253         return __get_dma_pages(GFP_KERNEL, order);
 254 }
 255
 256 /* DMA data buffer, DMA command buffer */
 257 static unsigned char *ltdmabuf;
 258 static unsigned char *ltdmacbuf;
 259
 260 /* private struct, holds our appletalk address */
 261
 262 struct ltpc_private
 263 {
 264         struct net_device_stats stats;
 265         struct atalk_addr my_addr;
 266 };
 267
 268 /* transmit queue element struct */
 269
 270 struct xmitQel {
 271         struct xmitQel *next;
 272         /* command buffer */
 273         unsigned char *cbuf;
 274         short cbuflen;
 275         /* data buffer */
 276         unsigned char *dbuf;
 277         short dbuflen;
 278         unsigned char QWrite;   /* read or write data */
 279         unsigned char mailbox;
 280 };
 281
 282 /* the transmit queue itself */
 283
 284 static struct xmitQel *xmQhd, *xmQtl;
 285
 286 static void enQ(struct xmitQel *qel)
 287 {
 288         unsigned long flags;
 289         qel->next = NULL;
 290
 291         spin_lock_irqsave(&txqueue_lock, flags);
 292         if (xmQtl) {
 293                 xmQtl->next = qel;
 294         } else {
 295                 xmQhd = qel;
 296         }
 297         xmQtl = qel;
 298         spin_unlock_irqrestore(&txqueue_lock, flags);
 299
 300         if (debug & DEBUG_LOWER)
 301                 printk("enqueued a 0x%02x command\n",qel->cbuf[0]);
 302 }
 303
 304 static struct xmitQel *deQ(void)
 305 {
 306         unsigned long flags;
 307         int i;
 308         struct xmitQel *qel=NULL;
 309
 310         spin_lock_irqsave(&txqueue_lock, flags);
 311         if (xmQhd) {
 312                 qel = xmQhd;
 313                 xmQhd = qel->next;
 314                 if(!xmQhd) xmQtl = NULL;
 315         }
 316         spin_unlock_irqrestore(&txqueue_lock, flags);
 317
 318         if ((debug & DEBUG_LOWER) && qel) {
 319                 int n;
 320                 printk(KERN_DEBUG "ltpc: dequeued command ");
 321                 n = qel->cbuflen;
 322                 if (n>100) n=100;
 323                 for(i=0;i<n;i++) printk("%02x ",qel->cbuf[i]);
 324                 printk("\n");
 325         }
 326
 327         return qel;
 328 }
 329
 330 /* and... the queue elements we'll be using */
 331 static struct xmitQel qels[16];
 332
 333 /* and their corresponding mailboxes */
 334 static unsigned char mailbox[16];
 335 static unsigned char mboxinuse[16] = {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
 336
 337 static int wait_timeout(struct net_device *dev, int c)
 338 {
 339         /* returns true if it stayed c */
 340         /* this uses base+6, but it's ok */
 341         int i;
 342
 343         /* twenty second or so total */
 344
 345         for(i=0;i<200000;i++) {
 346                 if ( c != inb_p(dev->base_addr+6) ) return 0;
 347                 udelay(100);
 348         }
 349         return 1; /* timed out */
 350 }
 351
 352 /* get the first free mailbox */
 353
 354 static int getmbox(void)
 355 {
 356         unsigned long flags;
 357         int i;
 358
 359         spin_lock_irqsave(&mbox_lock, flags);
 360         for(i=1;i<16;i++) if(!mboxinuse[i]) {
 361                 mboxinuse[i]=1;
 362                 spin_unlock_irqrestore(&mbox_lock, flags);
 363                 return i;
 364         }
 365         spin_unlock_irqrestore(&mbox_lock, flags);
 366         return 0;
 367 }
 368
 369 /* read a command from the card */
 370 static void handlefc(struct net_device *dev)
 371 {
 372         /* called *only* from idle, non-reentrant */
 373         int dma = dev->dma;
 374         int base = dev->base_addr;
 375         unsigned long flags;
 376
 377
 378         flags=claim_dma_lock();
 379         disable_dma(dma);
 380         clear_dma_ff(dma);
 381         set_dma_mode(dma,DMA_MODE_READ);
 382         set_dma_addr(dma,virt_to_bus(ltdmacbuf));
 383         set_dma_count(dma,50);
 384         enable_dma(dma);
 385         release_dma_lock(flags);
 386
 387         inb_p(base+3);
 388         inb_p(base+2);
 389
 390         if ( wait_timeout(dev,0xfc) ) printk("timed out in handlefc\n");
 391 }
 392
 393 /* read data from the card */
 394 static void handlefd(struct net_device *dev)
 395 {
 396         int dma = dev->dma;
 397         int base = dev->base_addr;
 398         unsigned long flags;
 399
 400         flags=claim_dma_lock();
 401         disable_dma(dma);
 402         clear_dma_ff(dma);
 403         set_dma_mode(dma,DMA_MODE_READ);
 404         set_dma_addr(dma,virt_to_bus(ltdmabuf));
 405         set_dma_count(dma,800);
 406         enable_dma(dma);
 407         release_dma_lock(flags);
 408
 409         inb_p(base+3);
 410         inb_p(base+2);
 411
 412         if ( wait_timeout(dev,0xfd) ) printk("timed out in handlefd\n");
 413         sendup_buffer(dev);
 414 }
 415
 416 static void handlewrite(struct net_device *dev)
 417 {
 418         /* called *only* from idle, non-reentrant */
 419         /* on entry, 0xfb and ltdmabuf holds data */
 420         int dma = dev->dma;
 421         int base = dev->base_addr;
 422         unsigned long flags;
 423
 424         flags=claim_dma_lock();
 425         disable_dma(dma);
 426         clear_dma_ff(dma);
 427         set_dma_mode(dma,DMA_MODE_WRITE);
 428         set_dma_addr(dma,virt_to_bus(ltdmabuf));
 429         set_dma_count(dma,800);
 430         enable_dma(dma);
 431         release_dma_lock(flags);
 432
 433         inb_p(base+3);
 434         inb_p(base+2);
 435
 436         if ( wait_timeout(dev,0xfb) ) {
 437                 flags=claim_dma_lock();
 438                 printk("timed out in handlewrite, dma res %d\n",
 439                         get_dma_residue(dev->dma) );
 440                 release_dma_lock(flags);
 441         }
 442 }
 443
 444 static void handleread(struct net_device *dev)
 445 {
 446         /* on entry, 0xfb */
 447         /* on exit, ltdmabuf holds data */
 448         int dma = dev->dma;
 449         int base = dev->base_addr;
 450         unsigned long flags;
 451
 452
 453         flags=claim_dma_lock();
 454         disable_dma(dma);
 455         clear_dma_ff(dma);
 456         set_dma_mode(dma,DMA_MODE_READ);
 457         set_dma_addr(dma,virt_to_bus(ltdmabuf));
 458         set_dma_count(dma,800);
 459         enable_dma(dma);
 460         release_dma_lock(flags);
 461
 462         inb_p(base+3);
 463         inb_p(base+2);
 464         if ( wait_timeout(dev,0xfb) ) printk("timed out in handleread\n");
 465 }
 466
 467 static void handlecommand(struct net_device *dev)
 468 {
 469         /* on entry, 0xfa and ltdmacbuf holds command */
 470         int dma = dev->dma;
 471         int base = dev->base_addr;
 472         unsigned long flags;
 473
 474         flags=claim_dma_lock();
 475         disable_dma(dma);
 476         clear_dma_ff(dma);
 477         set_dma_mode(dma,DMA_MODE_WRITE);
 478         set_dma_addr(dma,virt_to_bus(ltdmacbuf));
 479         set_dma_count(dma,50);
 480         enable_dma(dma);
 481         release_dma_lock(flags);
 482         inb_p(base+3);
 483         inb_p(base+2);
 484         if ( wait_timeout(dev,0xfa) ) printk("timed out in handlecommand\n");
 485 }
 486
 487 /* ready made command for getting the result from the card */
 488 static unsigned char rescbuf[2] = {LT_GETRESULT,0};
 489 static unsigned char resdbuf[2];
 490
 491 static int QInIdle;
 492
 493 /* idle expects to be called with the IRQ line high -- either because of
 494  * an interrupt, or because the line is tri-stated
 495  */
 496
 497 static void idle(struct net_device *dev)
 498 {
 499         unsigned long flags;
 500         int state;
 501         /* FIXME This is initialized to shut the warning up, but I need to
 502          * think this through again.
 503          */
 504         struct xmitQel *q = NULL;
 505         int oops;
 506         int i;
 507         int base = dev->base_addr;
 508
 509         spin_lock_irqsave(&txqueue_lock, flags);
 510         if(QInIdle) {
 511                 spin_unlock_irqrestore(&txqueue_lock, flags);
 512                 return;
 513         }
 514         QInIdle = 1;
 515         spin_unlock_irqrestore(&txqueue_lock, flags);
 516
 517         /* this tri-states the IRQ line */
 518         (void) inb_p(base+6);
 519
 520         oops = 100;
 521
 522 loop:
 523         if (0>oops--) {
 524                 printk("idle: looped too many times\n");
 525                 goto done;
 526         }
 527
 528         state = inb_p(base+6);
 529         if (state != inb_p(base+6)) goto loop;
 530
 531         switch(state) {
 532                 case 0xfc:
 533                         /* incoming command */
 534                         if (debug & DEBUG_LOWER) printk("idle: fc\n");
 535                         handlefc(dev);
 536                         break;
 537                 case 0xfd:
 538                         /* incoming data */
 539                         if(debug & DEBUG_LOWER) printk("idle: fd\n");
 540                         handlefd(dev);
 541                         break;
 542                 case 0xf9:
 543                         /* result ready */
 544                         if (debug & DEBUG_LOWER) printk("idle: f9\n");
 545                         if(!mboxinuse[0]) {
 546                                 mboxinuse[0] = 1;
 547                                 qels[0].cbuf = rescbuf;
 548                                 qels[0].cbuflen = 2;
 549                                 qels[0].dbuf = resdbuf;
 550                                 qels[0].dbuflen = 2;
 551                                 qels[0].QWrite = 0;
 552                                 qels[0].mailbox = 0;
 553                                 enQ(&qels[0]);
 554                         }
 555                         inb_p(dev->base_addr+1);
 556                         inb_p(dev->base_addr+0);
 557                         if( wait_timeout(dev,0xf9) )
 558                                 printk("timed out idle f9\n");
 559                         break;
 560                 case 0xf8:
 561                         /* ?? */
 562                         if (xmQhd) {
 563                                 inb_p(dev->base_addr+1);
 564                                 inb_p(dev->base_addr+0);
 565                                 if(wait_timeout(dev,0xf8) )
 566                                         printk("timed out idle f8\n");
 567                         } else {
 568                                 goto done;
 569                         }
 570                         break;
 571                 case 0xfa:
 572                         /* waiting for command */
 573                         if(debug & DEBUG_LOWER) printk("idle: fa\n");
 574                         if (xmQhd) {
 575                                 q=deQ();
 576                                 memcpy(ltdmacbuf,q->cbuf,q->cbuflen);
 577                                 ltdmacbuf[1] = q->mailbox;
 578                                 if (debug>1) {
 579                                         int n;
 580                                         printk("ltpc: sent command     ");
 581                                         n = q->cbuflen;
 582                                         if (n>100) n=100;
 583                                         for(i=0;i<n;i++)
 584                                                 printk("%02x ",ltdmacbuf[i]);
 585                                         printk("\n");
 586                                 }
 587                                 handlecommand(dev);
 588                                         if(0xfa==inb_p(base+6)) {
 589                                                 /* we timed out, so return */
 590                                                 goto done;
 591                                         }
 592                         } else {
 593                                 /* we don't seem to have a command */
 594                                 if (!mboxinuse[0]) {
 595                                         mboxinuse[0] = 1;
 596                                         qels[0].cbuf = rescbuf;
 597                                         qels[0].cbuflen = 2;
 598                                         qels[0].dbuf = resdbuf;
 599                                         qels[0].dbuflen = 2;
 600                                         qels[0].QWrite = 0;
 601                                         qels[0].mailbox = 0;
 602                                         enQ(&qels[0]);
 603                                 } else {
 604                                         printk("trouble: response command already queued\n");
 605                                         goto done;
 606                                 }
 607                         }
 608                         break;
 609                 case 0Xfb:
 610                         /* data transfer ready */
 611                         if(debug & DEBUG_LOWER) printk("idle: fb\n");
 612                         if(q->QWrite) {
 613                                 memcpy(ltdmabuf,q->dbuf,q->dbuflen);
 614                                 handlewrite(dev);
 615                         } else {
 616                                 handleread(dev);
 617                                 /* non-zero mailbox numbers are for
 618                                    commmands, 0 is for GETRESULT
 619                                    requests */
 620                                 if(q->mailbox) {
 621                                         memcpy(q->dbuf,ltdmabuf,q->dbuflen);
 622                                 } else {
 623                                         /* this was a result */
 624                                         mailbox[ 0x0f & ltdmabuf[0] ] = ltdmabuf[1];
 625                                         mboxinuse[0]=0;
 626                                 }
 627                         }
 628                         break;
 629         }
 630         goto loop;
 631
 632 done:
 633         QInIdle=0;
 634
 635         /* now set the interrupts back as appropriate */
 636         /* the first read takes it out of tri-state (but still high) */
 637         /* the second resets it */
 638         /* note that after this point, any read of base+6 will
 639            trigger an interrupt */
 640
 641         if (dev->irq) {
 642                 inb_p(base+7);
 643                 inb_p(base+7);
 644         }
 645         return;
 646 }
 647
 648
 649 static int do_write(struct net_device *dev, void *cbuf, int cbuflen,
 650         void *dbuf, int dbuflen)
 651 {
 652
 653         int i = getmbox();
 654         int ret;
 655
 656         if(i) {
 657                 qels[i].cbuf = (unsigned char *) cbuf;
 658                 qels[i].cbuflen = cbuflen;
 659                 qels[i].dbuf = (unsigned char *) dbuf;
 660                 qels[i].dbuflen = dbuflen;
 661                 qels[i].QWrite = 1;
 662                 qels[i].mailbox = i;  /* this should be initted rather */
 663                 enQ(&qels[i]);
 664                 idle(dev);
 665                 ret = mailbox[i];
 666                 mboxinuse[i]=0;
 667                 return ret;
 668         }
 669         printk("ltpc: could not allocate mbox\n");
 670         return -1;
 671 }
 672
 673 static int do_read(struct net_device *dev, void *cbuf, int cbuflen,
 674         void *dbuf, int dbuflen)
 675 {
 676
 677         int i = getmbox();
 678         int ret;
 679
 680         if(i) {
 681                 qels[i].cbuf = (unsigned char *) cbuf;
 682                 qels[i].cbuflen = cbuflen;
 683                 qels[i].dbuf = (unsigned char *) dbuf;
 684                 qels[i].dbuflen = dbuflen;
 685                 qels[i].QWrite = 0;
 686                 qels[i].mailbox = i;  /* this should be initted rather */
 687                 enQ(&qels[i]);
 688                 idle(dev);
 689                 ret = mailbox[i];
 690                 mboxinuse[i]=0;
 691                 return ret;
 692         }
 693         printk("ltpc: could not allocate mbox\n");
 694         return -1;
 695 }
 696
 697 /* end of idle handlers -- what should be seen is do_read, do_write */
 698
 699 static struct timer_list ltpc_timer;
 700
 701 static int ltpc_xmit(struct sk_buff *skb, struct net_device *dev);
 702 static struct net_device_stats *ltpc_get_stats(struct net_device *dev);
 703
 704 static int read_30 ( struct net_device *dev)
 705 {
 706         lt_command c;
 707         c.getflags.command = LT_GETFLAGS;
 708         return do_read(dev, &c, sizeof(c.getflags),&c,0);
 709 }
 710
 711 static int set_30 (struct net_device *dev,int x)
 712 {
 713         lt_command c;
 714         c.setflags.command = LT_SETFLAGS;
 715         c.setflags.flags = x;
 716         return do_write(dev, &c, sizeof(c.setflags),&c,0);
 717 }
 718
 719 /* LLAP to DDP translation */
 720
 721 static int sendup_buffer (struct net_device *dev)
 722 {
 723         /* on entry, command is in ltdmacbuf, data in ltdmabuf */
 724         /* called from idle, non-reentrant */
 725
 726         int dnode, snode, llaptype, len;
 727         int sklen;
 728         struct sk_buff *skb;
 729         struct net_device_stats *stats = &((struct ltpc_private *)dev->priv)->stats;
 730         struct lt_rcvlap *ltc = (struct lt_rcvlap *) ltdmacbuf;
 731
 732         if (ltc->command != LT_RCVLAP) {
 733                 printk("unknown command 0x%02x from ltpc card\n",ltc->command);
 734                 return(-1);
 735         }
 736         dnode = ltc->dnode;
 737         snode = ltc->snode;
 738         llaptype = ltc->laptype;
 739         len = ltc->length;
 740
 741         sklen = len;
 742         if (llaptype == 1)
 743                 sklen += 8;  /* correct for short ddp */
 744         if(sklen > 800) {
 745                 printk(KERN_INFO "%s: nonsense length in ltpc command 0x14: 0x%08x\n",
 746                         dev->name,sklen);
 747                 return -1;
 748         }
 749
 750         if ( (llaptype==0) || (llaptype>2) ) {
 751                 printk(KERN_INFO "%s: unknown LLAP type: %d\n",dev->name,llaptype);
 752                 return -1;
 753         }
 754
 755
 756         skb = dev_alloc_skb(3+sklen);
 757         if (skb == NULL)
 758         {
 759                 printk("%s: dropping packet due to memory squeeze.\n",
 760                         dev->name);
 761                 return -1;
 762         }
 763         skb->dev = dev;
 764
 765         if (sklen > len)
 766                 skb_reserve(skb,8);
 767         skb_put(skb,len+3);
 768         skb->protocol = htons(ETH_P_LOCALTALK);
 769         /* add LLAP header */
 770         skb->data[0] = dnode;
 771         skb->data[1] = snode;
 772         skb->data[2] = llaptype;
 773         skb_reset_mac_header(skb);      /* save pointer to llap header */
 774         skb_pull(skb,3);
 775
 776         /* copy ddp(s,e)hdr + contents */
 777         skb_copy_to_linear_data(skb, ltdmabuf, len);
 778
 779         skb_reset_transport_header(skb);
 780
 781         stats->rx_packets++;
 782         stats->rx_bytes+=skb->len;
 783
 784         /* toss it onwards */
 785         netif_rx(skb);
 786         dev->last_rx = jiffies;
 787         return 0;
 788 }
 789
 790 /* the handler for the board interrupt */
 791
 792 static irqreturn_t
 793 ltpc_interrupt(int irq, void *dev_id)
 794 {
 795         struct net_device *dev = dev_id;
 796
 797         if (dev==NULL) {
 798                 printk("ltpc_interrupt: unknown device.\n");
 799                 return IRQ_NONE;
 800         }
 801
 802         inb_p(dev->base_addr+6);  /* disable further interrupts from board */
 803
 804         idle(dev); /* handle whatever is coming in */
 805
 806         /* idle re-enables interrupts from board */
 807
 808         return IRQ_HANDLED;
 809 }
 810
 811 /***
 812  *
 813  *    The ioctls that the driver responds to are:
 814  *
 815  *    SIOCSIFADDR -- do probe using the passed node hint.
 816  *    SIOCGIFADDR -- return net, node.
 817  *
 818  *    some of this stuff should be done elsewhere.
 819  *
 820  ***/
 821
 822 static int ltpc_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
 823 {
 824         struct sockaddr_at *sa = (struct sockaddr_at *) &ifr->ifr_addr;
 825         /* we'll keep the localtalk node address in dev->pa_addr */
 826         struct atalk_addr *aa = &((struct ltpc_private *)dev->priv)->my_addr;
 827         struct lt_init c;
 828         int ltflags;
 829
 830         if(debug & DEBUG_VERBOSE) printk("ltpc_ioctl called\n");
 831
 832         switch(cmd) {
 833                 case SIOCSIFADDR:
 834
 835                         aa->s_net  = sa->sat_addr.s_net;
 836
 837                         /* this does the probe and returns the node addr */
 838                         c.command = LT_INIT;
 839                         c.hint = sa->sat_addr.s_node;
 840
 841                         aa->s_node = do_read(dev,&c,sizeof(c),&c,0);
 842
 843                         /* get all llap frames raw */
 844                         ltflags = read_30(dev);
 845                         ltflags |= LT_FLAG_ALLLAP;
 846                         set_30 (dev,ltflags);
 847
 848                         dev->broadcast[0] = 0xFF;
 849                         dev->dev_addr[0] = aa->s_node;
 850
 851                         dev->addr_len=1;
 852
 853                         return 0;
 854
 855                 case SIOCGIFADDR:
 856
 857                         sa->sat_addr.s_net = aa->s_net;
 858                         sa->sat_addr.s_node = aa->s_node;
 859
 860                         return 0;
 861
 862                 default:
 863                         return -EINVAL;
 864         }
 865 }
 866
 867 static void set_multicast_list(struct net_device *dev)
 868 {
 869         /* This needs to be present to keep netatalk happy. */
 870         /* Actually netatalk needs fixing! */
 871 }
 872
 873 static int ltpc_poll_counter;
 874
 875 static void ltpc_poll(unsigned long l)
 876 {
 877         struct net_device *dev = (struct net_device *) l;
 878
 879         del_timer(&ltpc_timer);
 880
 881         if(debug & DEBUG_VERBOSE) {
 882                 if (!ltpc_poll_counter) {
 883                         ltpc_poll_counter = 50;
 884                         printk("ltpc poll is alive\n");
 885                 }
 886                 ltpc_poll_counter--;
 887         }
 888
 889         if (!dev)
 890                 return;  /* we've been downed */
 891
 892         /* poll 20 times per second */
 893         idle(dev);
 894         ltpc_timer.expires = jiffies + HZ/20;
 895
 896         add_timer(&ltpc_timer);
 897 }
 898
 899 /* DDP to LLAP translation */
 900
 901 static int ltpc_xmit(struct sk_buff *skb, struct net_device *dev)
 902 {
 903         /* in kernel 1.3.xx, on entry skb->data points to ddp header,
 904          * and skb->len is the length of the ddp data + ddp header
 905          */
 906
 907         struct net_device_stats *stats = &((struct ltpc_private *)dev->priv)->stats;
 908
 909         int i;
 910         struct lt_sendlap cbuf;
 911         unsigned char *hdr;
 912
 913         cbuf.command = LT_SENDLAP;
 914         cbuf.dnode = skb->data[0];
 915         cbuf.laptype = skb->data[2];
 916         skb_pull(skb,3);        /* skip past LLAP header */
 917         cbuf.length = skb->len; /* this is host order */
 918         skb_reset_transport_header(skb);
 919
 920         if(debug & DEBUG_UPPER) {
 921                 printk("command ");
 922                 for(i=0;i<6;i++)
 923                         printk("%02x ",((unsigned char *)&cbuf)[i]);
 924                 printk("\n");
 925         }
 926
 927         hdr = skb_transport_header(skb);
 928         do_write(dev, &cbuf, sizeof(cbuf), hdr, skb->len);
 929
 930         if(debug & DEBUG_UPPER) {
 931                 printk("sent %d ddp bytes\n",skb->len);
 932                 for (i = 0; i < skb->len; i++)
 933                         printk("%02x ", hdr[i]);
 934                 printk("\n");
 935         }
 936
 937         stats->tx_packets++;
 938         stats->tx_bytes+=skb->len;
 939
 940         dev_kfree_skb(skb);
 941         return 0;
 942 }
 943
 944 static struct net_device_stats *ltpc_get_stats(struct net_device *dev)
 945 {
 946         struct net_device_stats *stats = &((struct ltpc_private *) dev->priv)->stats;
 947         return stats;
 948 }
 949
 950 /* initialization stuff */
 951
 952 static int __init ltpc_probe_dma(int base, int dma)
 953 {
 954         int want = (dma == 3) ? 2 : (dma == 1) ? 1 : 3;
 955         unsigned long timeout;
 956         unsigned long f;
 957
 958         if (want & 1) {
 959                 if (request_dma(1,"ltpc")) {
 960                         want &= ~1;
 961                 } else {
 962                         f=claim_dma_lock();
 963                         disable_dma(1);
 964                         clear_dma_ff(1);
 965                         set_dma_mode(1,DMA_MODE_WRITE);
 966                         set_dma_addr(1,virt_to_bus(ltdmabuf));
 967                         set_dma_count(1,sizeof(struct lt_mem));
 968                         enable_dma(1);
 969                         release_dma_lock(f);
 970                 }
 971         }
 972         if (want & 2) {
 973                 if (request_dma(3,"ltpc")) {
 974                         want &= ~2;
 975                 } else {
 976                         f=claim_dma_lock();
 977                         disable_dma(3);
 978                         clear_dma_ff(3);
 979                         set_dma_mode(3,DMA_MODE_WRITE);
 980                         set_dma_addr(3,virt_to_bus(ltdmabuf));
 981                         set_dma_count(3,sizeof(struct lt_mem));
 982                         enable_dma(3);
 983                         release_dma_lock(f);
 984                 }
 985         }
 986         /* set up request */
 987
 988         /* FIXME -- do timings better! */
 989
 990         ltdmabuf[0] = LT_READMEM;
 991         ltdmabuf[1] = 1;  /* mailbox */
 992         ltdmabuf[2] = 0; ltdmabuf[3] = 0;  /* address */
 993         ltdmabuf[4] = 0; ltdmabuf[5] = 1;  /* read 0x0100 bytes */
 994         ltdmabuf[6] = 0; /* dunno if this is necessary */
 995
 996         inb_p(io+1);
 997         inb_p(io+0);
 998         timeout = jiffies+100*HZ/100;
 999         while(time_before(jiffies, timeout)) {
1000                 if ( 0xfa == inb_p(io+6) ) break;
1001         }
1002
1003         inb_p(io+3);
1004         inb_p(io+2);
1005         while(time_before(jiffies, timeout)) {
1006                 if ( 0xfb == inb_p(io+6) ) break;
1007         }
1008
1009         /* release the other dma channel (if we opened both of them) */
1010
1011         if ((want & 2) && (get_dma_residue(3)==sizeof(struct lt_mem))) {
1012                 want &= ~2;
1013                 free_dma(3);
1014         }
1015
1016         if ((want & 1) && (get_dma_residue(1)==sizeof(struct lt_mem))) {
1017                 want &= ~1;
1018                 free_dma(1);
1019         }
1020
1021         if (!want)
1022                 return 0;
1023
1024         return (want & 2) ? 3 : 1;
1025 }
1026
1027 struct net_device * __init ltpc_probe(void)
1028 {
1029         struct net_device *dev;
1030         int err = -ENOMEM;
1031         int x=0,y=0;
1032         int autoirq;
1033         unsigned long f;
1034         unsigned long timeout;
1035
1036         dev = alloc_ltalkdev(sizeof(struct ltpc_private));
1037         if (!dev)
1038                 goto out;
1039
1040         /* probe for the I/O port address */
1041
1042         if (io != 0x240 && request_region(0x220,8,"ltpc")) {
1043                 x = inb_p(0x220+6);
1044                 if ( (x!=0xff) && (x>=0xf0) ) {
1045                         io = 0x220;
1046                         goto got_port;
1047                 }
1048                 release_region(0x220,8);
1049         }
1050         if (io != 0x220 && request_region(0x240,8,"ltpc")) {
1051                 y = inb_p(0x240+6);
1052                 if ( (y!=0xff) && (y>=0xf0) ){
1053                         io = 0x240;
1054                         goto got_port;
1055                 }
1056                 release_region(0x240,8);
1057         }
1058
1059         /* give up in despair */
1060         printk(KERN_ERR "LocalTalk card not found; 220 = %02x, 240 = %02x.\n", x,y);
1061         err = -ENODEV;
1062         goto out1;
1063
1064  got_port:
1065         /* probe for the IRQ line */
1066         if (irq < 2) {
1067                 unsigned long irq_mask;
1068
1069                 irq_mask = probe_irq_on();
1070                 /* reset the interrupt line */
1071                 inb_p(io+7);
1072                 inb_p(io+7);
1073                 /* trigger an interrupt (I hope) */
1074                 inb_p(io+6);
1075                 mdelay(2);
1076                 autoirq = probe_irq_off(irq_mask);
1077
1078                 if (autoirq == 0) {
1079                         printk(KERN_ERR "ltpc: probe at %#x failed to detect IRQ line.\n", io);
1080                 } else {
1081                         irq = autoirq;
1082                 }
1083         }
1084
1085         /* allocate a DMA buffer */
1086         ltdmabuf = (unsigned char *) dma_mem_alloc(1000);
1087         if (!ltdmabuf) {
1088                 printk(KERN_ERR "ltpc: mem alloc failed\n");
1089                 err = -ENOMEM;
1090                 goto out2;
1091         }
1092
1093         ltdmacbuf = &ltdmabuf[800];
1094
1095         if(debug & DEBUG_VERBOSE) {
1096                 printk("ltdmabuf pointer %08lx\n",(unsigned long) ltdmabuf);
1097         }
1098
1099         /* reset the card */
1100
1101         inb_p(io+1);
1102         inb_p(io+3);
1103
1104         msleep(20);
1105
1106         inb_p(io+0);
1107         inb_p(io+2);
1108         inb_p(io+7); /* clear reset */
1109         inb_p(io+4);
1110         inb_p(io+5);
1111         inb_p(io+5); /* enable dma */
1112         inb_p(io+6); /* tri-state interrupt line */
1113
1114         ssleep(1);
1115
1116         /* now, figure out which dma channel we're using, unless it's
1117            already been specified */
1118         /* well, 0 is a legal DMA channel, but the LTPC card doesn't
1119            use it... */
1120         dma = ltpc_probe_dma(io, dma);
1121         if (!dma) {  /* no dma channel */
1122                 printk(KERN_ERR "No DMA channel found on ltpc card.\n");
1123                 err = -ENODEV;
1124                 goto out3;
1125         }
1126
1127         /* print out friendly message */
1128         if(irq)
1129                 printk(KERN_INFO "Apple/Farallon LocalTalk-PC card at %03x, IR%d, DMA%d.\n",io,irq,dma);
1130         else
1131                 printk(KERN_INFO "Apple/Farallon LocalTalk-PC card at %03x, DMA%d.  Using polled mode.\n",io,dma);
1132
1133         /* Fill in the fields of the device structure with ethernet-generic values. */
1134         dev->hard_start_xmit = ltpc_xmit;
1135         dev->get_stats = ltpc_get_stats;
1136
1137         /* add the ltpc-specific things */
1138         dev->do_ioctl = &ltpc_ioctl;
1139
1140         dev->set_multicast_list = &set_multicast_list;
1141         dev->mc_list = NULL;
1142         dev->base_addr = io;
1143         dev->irq = irq;
1144         dev->dma = dma;
1145
1146         /* the card will want to send a result at this point */
1147         /* (I think... leaving out this part makes the kernel crash,
1148            so I put it back in...) */
1149
1150         f=claim_dma_lock();
1151         disable_dma(dma);
1152         clear_dma_ff(dma);
1153         set_dma_mode(dma,DMA_MODE_READ);
1154         set_dma_addr(dma,virt_to_bus(ltdmabuf));
1155         set_dma_count(dma,0x100);
1156         enable_dma(dma);
1157         release_dma_lock(f);
1158
1159         (void) inb_p(io+3);
1160         (void) inb_p(io+2);
1161         timeout = jiffies+100*HZ/100;
1162
1163         while(time_before(jiffies, timeout)) {
1164                 if( 0xf9 == inb_p(io+6))
1165                         break;
1166                 schedule();
1167         }
1168
1169         if(debug & DEBUG_VERBOSE) {
1170                 printk("setting up timer and irq\n");
1171         }
1172
1173         /* grab it and don't let go :-) */
1174         if (irq && request_irq( irq, &ltpc_interrupt, 0, "ltpc", dev) >= 0)
1175         {
1176                 (void) inb_p(io+7);  /* enable interrupts from board */
1177                 (void) inb_p(io+7);  /* and reset irq line */
1178         } else {
1179                 if( irq )
1180                         printk(KERN_ERR "ltpc: IRQ already in use, using polled mode.\n");
1181                 dev->irq = 0;
1182                 /* polled mode -- 20 times per second */
1183                 /* this is really, really slow... should it poll more often? */
1184                 init_timer(&ltpc_timer);
1185                 ltpc_timer.function=ltpc_poll;
1186                 ltpc_timer.data = (unsigned long) dev;
1187
1188                 ltpc_timer.expires = jiffies + HZ/20;
1189                 add_timer(&ltpc_timer);
1190         }
1191         err = register_netdev(dev);
1192         if (err)
1193                 goto out4;
1194
1195         return NULL;
1196 out4:
1197         del_timer_sync(&ltpc_timer);
1198         if (dev->irq)
1199                 free_irq(dev->irq, dev);
1200 out3:
1201         free_pages((unsigned long)ltdmabuf, get_order(1000));
1202 out2:
1203         release_region(io, 8);
1204 out1:
1205         free_netdev(dev);
1206 out:
1207         return ERR_PTR(err);
1208 }
1209
1210 #ifndef MODULE
1211 /* handles "ltpc=io,irq,dma" kernel command lines */
1212 static int __init ltpc_setup(char *str)
1213 {
1214         int ints[5];
1215
1216         str = get_options(str, ARRAY_SIZE(ints), ints);
1217
1218         if (ints[0] == 0) {
1219                 if (str && !strncmp(str, "auto", 4)) {
1220                         /* do nothing :-) */
1221                 }
1222                 else {
1223                         /* usage message */
1224                         printk (KERN_ERR
1225                                 "ltpc: usage: ltpc=auto|iobase[,irq[,dma]]\n");
1226                         return 0;
1227                 }
1228         } else {
1229                 io = ints[1];
1230                 if (ints[0] > 1) {
1231                         irq = ints[2];
1232                 }
1233                 if (ints[0] > 2) {
1234                         dma = ints[3];
1235                 }
1236                 /* ignore any other paramters */
1237         }
1238         return 1;
1239 }
1240
1241 __setup("ltpc=", ltpc_setup);
1242 #endif /* MODULE */
1243
1244 static struct net_device *dev_ltpc;
1245
1246 #ifdef MODULE
1247
1248 MODULE_LICENSE("GPL");
1249 module_param(debug, int, 0);
1250 module_param(io, int, 0);
1251 module_param(irq, int, 0);
1252 module_param(dma, int, 0);
1253
1254
1255 int __init init_module(void)
1256 {
1257         if(io == 0)
1258                 printk(KERN_NOTICE
1259                        "ltpc: Autoprobing is not recommended for modules\n");
1260
1261         dev_ltpc = ltpc_probe();
1262         if (IS_ERR(dev_ltpc))
1263                 return PTR_ERR(dev_ltpc);
1264         return 0;
1265 }
1266 #endif
1267
1268 static void __exit ltpc_cleanup(void)
1269 {
1270
1271         if(debug & DEBUG_VERBOSE) printk("unregister_netdev\n");
1272         unregister_netdev(dev_ltpc);
1273
1274         ltpc_timer.data = 0;  /* signal the poll routine that we're done */
1275
1276         del_timer_sync(&ltpc_timer);
1277
1278         if(debug & DEBUG_VERBOSE) printk("freeing irq\n");
1279
1280         if (dev_ltpc->irq)
1281                 free_irq(dev_ltpc->irq, dev_ltpc);
1282
1283         if(debug & DEBUG_VERBOSE) printk("freeing dma\n");
1284
1285         if (dev_ltpc->dma)
1286                 free_dma(dev_ltpc->dma);
1287
1288         if(debug & DEBUG_VERBOSE) printk("freeing ioaddr\n");
1289
1290         if (dev_ltpc->base_addr)
1291                 release_region(dev_ltpc->base_addr,8);
1292
1293         free_netdev(dev_ltpc);
1294
1295         if(debug & DEBUG_VERBOSE) printk("free_pages\n");
1296
1297         free_pages( (unsigned long) ltdmabuf, get_order(1000));
1298
1299         if(debug & DEBUG_VERBOSE) printk("returning from cleanup_module\n");
1300 }
1301
1302 module_exit(ltpc_cleanup);