drivers/serial/pmac_zilog.h

   1 #ifndef __PMAC_ZILOG_H__
   2 #define __PMAC_ZILOG_H__
   3
   4 #define pmz_debug(fmt,arg...)   dev_dbg(&uap->dev->ofdev.dev, fmt, ## arg)
   5
   6 /*
   7  * At most 2 ESCCs with 2 ports each
   8  */
   9 #define MAX_ZS_PORTS    4
  10
  11 /*
  12  * We wrap our port structure around the generic uart_port.
  13  */
  14 #define NUM_ZSREGS    17
  15
  16 struct uart_pmac_port {
  17         struct uart_port                port;
  18         struct uart_pmac_port           *mate;
  19
  20         /* macio_dev for the escc holding this port (maybe be null on
  21          * early inited port)
  22          */
  23         struct macio_dev                *dev;
  24         /* device node to this port, this points to one of 2 childs
  25          * of "escc" node (ie. ch-a or ch-b)
  26          */
  27         struct device_node              *node;
  28
  29         /* Port type as obtained from device tree (IRDA, modem, ...) */
  30         int                             port_type;
  31         u8                              curregs[NUM_ZSREGS];
  32
  33         unsigned int                    flags;
  34 #define PMACZILOG_FLAG_IS_CONS          0x00000001
  35 #define PMACZILOG_FLAG_IS_KGDB          0x00000002
  36 #define PMACZILOG_FLAG_MODEM_STATUS     0x00000004
  37 #define PMACZILOG_FLAG_IS_CHANNEL_A     0x00000008
  38 #define PMACZILOG_FLAG_REGS_HELD        0x00000010
  39 #define PMACZILOG_FLAG_TX_STOPPED       0x00000020
  40 #define PMACZILOG_FLAG_TX_ACTIVE        0x00000040
  41 #define PMACZILOG_FLAG_ENABLED          0x00000080
  42 #define PMACZILOG_FLAG_IS_IRDA          0x00000100
  43 #define PMACZILOG_FLAG_IS_INTMODEM      0x00000200
  44 #define PMACZILOG_FLAG_HAS_DMA          0x00000400
  45 #define PMACZILOG_FLAG_RSRC_REQUESTED   0x00000800
  46 #define PMACZILOG_FLAG_IS_ASLEEP        0x00001000
  47 #define PMACZILOG_FLAG_IS_OPEN          0x00002000
  48 #define PMACZILOG_FLAG_IS_IRQ_ON        0x00004000
  49 #define PMACZILOG_FLAG_IS_EXTCLK        0x00008000
  50 #define PMACZILOG_FLAG_BREAK            0x00010000
  51
  52         unsigned char                   parity_mask;
  53         unsigned char                   prev_status;
  54
  55         volatile u8                     __iomem *control_reg;
  56         volatile u8                     __iomem *data_reg;
  57
  58         unsigned int                    tx_dma_irq;
  59         unsigned int                    rx_dma_irq;
  60         volatile struct dbdma_regs      __iomem *tx_dma_regs;
  61         volatile struct dbdma_regs      __iomem *rx_dma_regs;
  62
  63         struct ktermios                 termios_cache;
  64 };
  65
  66 #define to_pmz(p) ((struct uart_pmac_port *)(p))
  67
  68 static inline struct uart_pmac_port *pmz_get_port_A(struct uart_pmac_port *uap)
  69 {
  70         if (uap->flags & PMACZILOG_FLAG_IS_CHANNEL_A)
  71                 return uap;
  72         return uap->mate;
  73 }
  74
  75 /*
  76  * Register acessors. Note that we don't need to enforce a recovery
  77  * delay on PCI PowerMac hardware, it's dealt in HW by the MacIO chip,
  78  * though if we try to use this driver on older machines, we might have
  79  * to add it back
  80  */
  81 static inline u8 read_zsreg(struct uart_pmac_port *port, u8 reg)
  82 {
  83         if (reg != 0)
  84                 writeb(reg, port->control_reg);
  85         return readb(port->control_reg);
  86 }
  87
  88 static inline void write_zsreg(struct uart_pmac_port *port, u8 reg, u8 value)
  89 {
  90         if (reg != 0)
  91                 writeb(reg, port->control_reg);
  92         writeb(value, port->control_reg);
  93 }
  94
  95 static inline u8 read_zsdata(struct uart_pmac_port *port)
  96 {
  97         return readb(port->data_reg);
  98 }
  99
 100 static inline void write_zsdata(struct uart_pmac_port *port, u8 data)
 101 {
 102         writeb(data, port->data_reg);
 103 }
 104
 105 static inline void zssync(struct uart_pmac_port *port)
 106 {
 107         (void)readb(port->control_reg);
 108 }
 109
 110 /* Conversion routines to/from brg time constants from/to bits
 111  * per second.
 112  */
 113 #define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
 114 #define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
 115
 116 #define ZS_CLOCK         3686400        /* Z8530 RTxC input clock rate */
 117
 118 /* The Zilog register set */
 119
 120 #define FLAG    0x7e
 121
 122 /* Write Register 0 */
 123 #define R0      0               /* Register selects */
 124 #define R1      1
 125 #define R2      2
 126 #define R3      3
 127 #define R4      4
 128 #define R5      5
 129 #define R6      6
 130 #define R7      7
 131 #define R8      8
 132 #define R9      9
 133 #define R10     10
 134 #define R11     11
 135 #define R12     12
 136 #define R13     13
 137 #define R14     14
 138 #define R15     15
 139 #define R7P     16
 140
 141 #define NULLCODE        0       /* Null Code */
 142 #define POINT_HIGH      0x8     /* Select upper half of registers */
 143 #define RES_EXT_INT     0x10    /* Reset Ext. Status Interrupts */
 144 #define SEND_ABORT      0x18    /* HDLC Abort */
 145 #define RES_RxINT_FC    0x20    /* Reset RxINT on First Character */
 146 #define RES_Tx_P        0x28    /* Reset TxINT Pending */
 147 #define ERR_RES         0x30    /* Error Reset */
 148 #define RES_H_IUS       0x38    /* Reset highest IUS */
 149
 150 #define RES_Rx_CRC      0x40    /* Reset Rx CRC Checker */
 151 #define RES_Tx_CRC      0x80    /* Reset Tx CRC Checker */
 152 #define RES_EOM_L       0xC0    /* Reset EOM latch */
 153
 154 /* Write Register 1 */
 155
 156 #define EXT_INT_ENAB    0x1     /* Ext Int Enable */
 157 #define TxINT_ENAB      0x2     /* Tx Int Enable */
 158 #define PAR_SPEC        0x4     /* Parity is special condition */
 159
 160 #define RxINT_DISAB     0       /* Rx Int Disable */
 161 #define RxINT_FCERR     0x8     /* Rx Int on First Character Only or Error */
 162 #define INT_ALL_Rx      0x10    /* Int on all Rx Characters or error */
 163 #define INT_ERR_Rx      0x18    /* Int on error only */
 164 #define RxINT_MASK      0x18
 165
 166 #define WT_RDY_RT       0x20    /* W/Req reflects recv if 1, xmit if 0 */
 167 #define WT_FN_RDYFN     0x40    /* W/Req pin is DMA request if 1, wait if 0 */
 168 #define WT_RDY_ENAB     0x80    /* Enable W/Req pin */
 169
 170 /* Write Register #2 (Interrupt Vector) */
 171
 172 /* Write Register 3 */
 173
 174 #define RxENABLE        0x1     /* Rx Enable */
 175 #define SYNC_L_INH      0x2     /* Sync Character Load Inhibit */
 176 #define ADD_SM          0x4     /* Address Search Mode (SDLC) */
 177 #define RxCRC_ENAB      0x8     /* Rx CRC Enable */
 178 #define ENT_HM          0x10    /* Enter Hunt Mode */
 179 #define AUTO_ENAB       0x20    /* Auto Enables */
 180 #define Rx5             0x0     /* Rx 5 Bits/Character */
 181 #define Rx7             0x40    /* Rx 7 Bits/Character */
 182 #define Rx6             0x80    /* Rx 6 Bits/Character */
 183 #define Rx8             0xc0    /* Rx 8 Bits/Character */
 184 #define RxN_MASK        0xc0
 185
 186 /* Write Register 4 */
 187
 188 #define PAR_ENAB        0x1     /* Parity Enable */
 189 #define PAR_EVEN        0x2     /* Parity Even/Odd* */
 190
 191 #define SYNC_ENAB       0       /* Sync Modes Enable */
 192 #define SB1             0x4     /* 1 stop bit/char */
 193 #define SB15            0x8     /* 1.5 stop bits/char */
 194 #define SB2             0xc     /* 2 stop bits/char */
 195 #define SB_MASK         0xc
 196
 197 #define MONSYNC         0       /* 8 Bit Sync character */
 198 #define BISYNC          0x10    /* 16 bit sync character */
 199 #define SDLC            0x20    /* SDLC Mode (01111110 Sync Flag) */
 200 #define EXTSYNC         0x30    /* External Sync Mode */
 201
 202 #define X1CLK           0x0     /* x1 clock mode */
 203 #define X16CLK          0x40    /* x16 clock mode */
 204 #define X32CLK          0x80    /* x32 clock mode */
 205 #define X64CLK          0xC0    /* x64 clock mode */
 206 #define XCLK_MASK       0xC0
 207
 208 /* Write Register 5 */
 209
 210 #define TxCRC_ENAB      0x1     /* Tx CRC Enable */
 211 #define RTS             0x2     /* RTS */
 212 #define SDLC_CRC        0x4     /* SDLC/CRC-16 */
 213 #define TxENABLE        0x8     /* Tx Enable */
 214 #define SND_BRK         0x10    /* Send Break */
 215 #define Tx5             0x0     /* Tx 5 bits (or less)/character */
 216 #define Tx7             0x20    /* Tx 7 bits/character */
 217 #define Tx6             0x40    /* Tx 6 bits/character */
 218 #define Tx8             0x60    /* Tx 8 bits/character */
 219 #define TxN_MASK        0x60
 220 #define DTR             0x80    /* DTR */
 221
 222 /* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
 223
 224 /* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
 225
 226 /* Write Register 7' (Some enhanced feature control) */
 227 #define ENEXREAD        0x40    /* Enable read of some write registers */
 228
 229 /* Write Register 8 (transmit buffer) */
 230
 231 /* Write Register 9 (Master interrupt control) */
 232 #define VIS     1       /* Vector Includes Status */
 233 #define NV      2       /* No Vector */
 234 #define DLC     4       /* Disable Lower Chain */
 235 #define MIE     8       /* Master Interrupt Enable */
 236 #define STATHI  0x10    /* Status high */
 237 #define NORESET 0       /* No reset on write to R9 */
 238 #define CHRB    0x40    /* Reset channel B */
 239 #define CHRA    0x80    /* Reset channel A */
 240 #define FHWRES  0xc0    /* Force hardware reset */
 241
 242 /* Write Register 10 (misc control bits) */
 243 #define BIT6    1       /* 6 bit/8bit sync */
 244 #define LOOPMODE 2      /* SDLC Loop mode */
 245 #define ABUNDER 4       /* Abort/flag on SDLC xmit underrun */
 246 #define MARKIDLE 8      /* Mark/flag on idle */
 247 #define GAOP    0x10    /* Go active on poll */
 248 #define NRZ     0       /* NRZ mode */
 249 #define NRZI    0x20    /* NRZI mode */
 250 #define FM1     0x40    /* FM1 (transition = 1) */
 251 #define FM0     0x60    /* FM0 (transition = 0) */
 252 #define CRCPS   0x80    /* CRC Preset I/O */
 253
 254 /* Write Register 11 (Clock Mode control) */
 255 #define TRxCXT  0       /* TRxC = Xtal output */
 256 #define TRxCTC  1       /* TRxC = Transmit clock */
 257 #define TRxCBR  2       /* TRxC = BR Generator Output */
 258 #define TRxCDP  3       /* TRxC = DPLL output */
 259 #define TRxCOI  4       /* TRxC O/I */
 260 #define TCRTxCP 0       /* Transmit clock = RTxC pin */
 261 #define TCTRxCP 8       /* Transmit clock = TRxC pin */
 262 #define TCBR    0x10    /* Transmit clock = BR Generator output */
 263 #define TCDPLL  0x18    /* Transmit clock = DPLL output */
 264 #define RCRTxCP 0       /* Receive clock = RTxC pin */
 265 #define RCTRxCP 0x20    /* Receive clock = TRxC pin */
 266 #define RCBR    0x40    /* Receive clock = BR Generator output */
 267 #define RCDPLL  0x60    /* Receive clock = DPLL output */
 268 #define RTxCX   0x80    /* RTxC Xtal/No Xtal */
 269
 270 /* Write Register 12 (lower byte of baud rate generator time constant) */
 271
 272 /* Write Register 13 (upper byte of baud rate generator time constant) */
 273
 274 /* Write Register 14 (Misc control bits) */
 275 #define BRENAB  1       /* Baud rate generator enable */
 276 #define BRSRC   2       /* Baud rate generator source */
 277 #define DTRREQ  4       /* DTR/Request function */
 278 #define AUTOECHO 8      /* Auto Echo */
 279 #define LOOPBAK 0x10    /* Local loopback */
 280 #define SEARCH  0x20    /* Enter search mode */
 281 #define RMC     0x40    /* Reset missing clock */
 282 #define DISDPLL 0x60    /* Disable DPLL */
 283 #define SSBR    0x80    /* Set DPLL source = BR generator */
 284 #define SSRTxC  0xa0    /* Set DPLL source = RTxC */
 285 #define SFMM    0xc0    /* Set FM mode */
 286 #define SNRZI   0xe0    /* Set NRZI mode */
 287
 288 /* Write Register 15 (external/status interrupt control) */
 289 #define EN85C30 1       /* Enable some 85c30-enhanced registers */
 290 #define ZCIE    2       /* Zero count IE */
 291 #define ENSTFIFO 4      /* Enable status FIFO (SDLC) */
 292 #define DCDIE   8       /* DCD IE */
 293 #define SYNCIE  0x10    /* Sync/hunt IE */
 294 #define CTSIE   0x20    /* CTS IE */
 295 #define TxUIE   0x40    /* Tx Underrun/EOM IE */
 296 #define BRKIE   0x80    /* Break/Abort IE */
 297
 298
 299 /* Read Register 0 */
 300 #define Rx_CH_AV        0x1     /* Rx Character Available */
 301 #define ZCOUNT          0x2     /* Zero count */
 302 #define Tx_BUF_EMP      0x4     /* Tx Buffer empty */
 303 #define DCD             0x8     /* DCD */
 304 #define SYNC_HUNT       0x10    /* Sync/hunt */
 305 #define CTS             0x20    /* CTS */
 306 #define TxEOM           0x40    /* Tx underrun */
 307 #define BRK_ABRT        0x80    /* Break/Abort */
 308
 309 /* Read Register 1 */
 310 #define ALL_SNT         0x1     /* All sent */
 311 /* Residue Data for 8 Rx bits/char programmed */
 312 #define RES3            0x8     /* 0/3 */
 313 #define RES4            0x4     /* 0/4 */
 314 #define RES5            0xc     /* 0/5 */
 315 #define RES6            0x2     /* 0/6 */
 316 #define RES7            0xa     /* 0/7 */
 317 #define RES8            0x6     /* 0/8 */
 318 #define RES18           0xe     /* 1/8 */
 319 #define RES28           0x0     /* 2/8 */
 320 /* Special Rx Condition Interrupts */
 321 #define PAR_ERR         0x10    /* Parity error */
 322 #define Rx_OVR          0x20    /* Rx Overrun Error */
 323 #define CRC_ERR         0x40    /* CRC/Framing Error */
 324 #define END_FR          0x80    /* End of Frame (SDLC) */
 325
 326 /* Read Register 2 (channel b only) - Interrupt vector */
 327 #define CHB_Tx_EMPTY    0x00
 328 #define CHB_EXT_STAT    0x02
 329 #define CHB_Rx_AVAIL    0x04
 330 #define CHB_SPECIAL     0x06
 331 #define CHA_Tx_EMPTY    0x08
 332 #define CHA_EXT_STAT    0x0a
 333 #define CHA_Rx_AVAIL    0x0c
 334 #define CHA_SPECIAL     0x0e
 335 #define STATUS_MASK     0x06
 336
 337 /* Read Register 3 (interrupt pending register) ch a only */
 338 #define CHBEXT  0x1             /* Channel B Ext/Stat IP */
 339 #define CHBTxIP 0x2             /* Channel B Tx IP */
 340 #define CHBRxIP 0x4             /* Channel B Rx IP */
 341 #define CHAEXT  0x8             /* Channel A Ext/Stat IP */
 342 #define CHATxIP 0x10            /* Channel A Tx IP */
 343 #define CHARxIP 0x20            /* Channel A Rx IP */
 344
 345 /* Read Register 8 (receive data register) */
 346
 347 /* Read Register 10  (misc status bits) */
 348 #define ONLOOP  2               /* On loop */
 349 #define LOOPSEND 0x10           /* Loop sending */
 350 #define CLK2MIS 0x40            /* Two clocks missing */
 351 #define CLK1MIS 0x80            /* One clock missing */
 352
 353 /* Read Register 12 (lower byte of baud rate generator constant) */
 354
 355 /* Read Register 13 (upper byte of baud rate generator constant) */
 356
 357 /* Read Register 15 (value of WR 15) */
 358
 359 /* Misc macros */
 360 #define ZS_CLEARERR(port)    (write_zsreg(port, 0, ERR_RES))
 361 #define ZS_CLEARFIFO(port)   do { volatile unsigned char garbage; \
 362                                      garbage = read_zsdata(port); \
 363                                      garbage = read_zsdata(port); \
 364                                      garbage = read_zsdata(port); \
 365                                 } while(0)
 366
 367 #define ZS_IS_CONS(UP)                  ((UP)->flags & PMACZILOG_FLAG_IS_CONS)
 368 #define ZS_IS_KGDB(UP)                  ((UP)->flags & PMACZILOG_FLAG_IS_KGDB)
 369 #define ZS_IS_CHANNEL_A(UP)             ((UP)->flags & PMACZILOG_FLAG_IS_CHANNEL_A)
 370 #define ZS_REGS_HELD(UP)                ((UP)->flags & PMACZILOG_FLAG_REGS_HELD)
 371 #define ZS_TX_STOPPED(UP)               ((UP)->flags & PMACZILOG_FLAG_TX_STOPPED)
 372 #define ZS_TX_ACTIVE(UP)                ((UP)->flags & PMACZILOG_FLAG_TX_ACTIVE)
 373 #define ZS_WANTS_MODEM_STATUS(UP)       ((UP)->flags & PMACZILOG_FLAG_MODEM_STATUS)
 374 #define ZS_IS_IRDA(UP)                  ((UP)->flags & PMACZILOG_FLAG_IS_IRDA)
 375 #define ZS_IS_INTMODEM(UP)              ((UP)->flags & PMACZILOG_FLAG_IS_INTMODEM)
 376 #define ZS_HAS_DMA(UP)                  ((UP)->flags & PMACZILOG_FLAG_HAS_DMA)
 377 #define ZS_IS_ASLEEP(UP)                ((UP)->flags & PMACZILOG_FLAG_IS_ASLEEP)
 378 #define ZS_IS_OPEN(UP)                  ((UP)->flags & PMACZILOG_FLAG_IS_OPEN)
 379 #define ZS_IS_IRQ_ON(UP)                ((UP)->flags & PMACZILOG_FLAG_IS_IRQ_ON)
 380 #define ZS_IS_EXTCLK(UP)                ((UP)->flags & PMACZILOG_FLAG_IS_EXTCLK)
 381
 382 #endif /* __PMAC_ZILOG_H__ */