cris: add arch/cris/include/asm/serial.h

[linux-2.6/next.git] / drivers / net / ks8851.c

/* drivers/net/ks8851.c
 *
 * Copyright 2009 Simtec Electronics
 *      http://www.simtec.co.uk/
 *      Ben Dooks <ben@simtec.co.uk>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

#define DEBUG

#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/ethtool.h>
#include <linux/cache.h>
#include <linux/crc32.h>
#include <linux/mii.h>

#include <linux/spi/spi.h>

#include "ks8851.h"

/**
 * struct ks8851_rxctrl - KS8851 driver rx control
 * @mchash: Multicast hash-table data.
 * @rxcr1: KS_RXCR1 register setting
 * @rxcr2: KS_RXCR2 register setting
 *
 * Representation of the settings needs to control the receive filtering
 * such as the multicast hash-filter and the receive register settings. This
 * is used to make the job of working out if the receive settings change and
 * then issuing the new settings to the worker that will send the necessary
 * commands.
 */
struct ks8851_rxctrl {
        u16     mchash[4];
        u16     rxcr1;
        u16     rxcr2;
};

/**
 * union ks8851_tx_hdr - tx header data
 * @txb: The header as bytes
 * @txw: The header as 16bit, little-endian words
 *
 * A dual representation of the tx header data to allow
 * access to individual bytes, and to allow 16bit accesses
 * with 16bit alignment.
 */
union ks8851_tx_hdr {
        u8      txb[6];
        __le16  txw[3];
};

/**
 * struct ks8851_net - KS8851 driver private data
 * @netdev: The network device we're bound to
 * @spidev: The spi device we're bound to.
 * @lock: Lock to ensure that the device is not accessed when busy.
 * @statelock: Lock on this structure for tx list.
 * @mii: The MII state information for the mii calls.
 * @rxctrl: RX settings for @rxctrl_work.
 * @tx_work: Work queue for tx packets
 * @irq_work: Work queue for servicing interrupts
 * @rxctrl_work: Work queue for updating RX mode and multicast lists
 * @txq: Queue of packets for transmission.
 * @spi_msg1: pre-setup SPI transfer with one message, @spi_xfer1.
 * @spi_msg2: pre-setup SPI transfer with two messages, @spi_xfer2.
 * @txh: Space for generating packet TX header in DMA-able data
 * @rxd: Space for receiving SPI data, in DMA-able space.
 * @txd: Space for transmitting SPI data, in DMA-able space.
 * @msg_enable: The message flags controlling driver output (see ethtool).
 * @fid: Incrementing frame id tag.
 * @rc_ier: Cached copy of KS_IER.
 * @rc_ccr: Cached copy of KS_CCR.
 * @rc_rxqcr: Cached copy of KS_RXQCR.
 * @eeprom_size: Companion eeprom size in Bytes, 0 if no eeprom
 *
 * The @lock ensures that the chip is protected when certain operations are
 * in progress. When the read or write packet transfer is in progress, most
 * of the chip registers are not ccessible until the transfer is finished and
 * the DMA has been de-asserted.
 *
 * The @statelock is used to protect information in the structure which may
 * need to be accessed via several sources, such as the network driver layer
 * or one of the work queues.
 *
 * We align the buffers we may use for rx/tx to ensure that if the SPI driver
 * wants to DMA map them, it will not have any problems with data the driver
 * modifies.
 */
struct ks8851_net {
        struct net_device       *netdev;
        struct spi_device       *spidev;
        struct mutex            lock;
        spinlock_t              statelock;

        union ks8851_tx_hdr     txh ____cacheline_aligned;
        u8                      rxd[8];
        u8                      txd[8];

        u32                     msg_enable ____cacheline_aligned;
        u16                     tx_space;
        u8                      fid;

        u16                     rc_ier;
        u16                     rc_rxqcr;
        u16                     rc_ccr;
        u16                     eeprom_size;

        struct mii_if_info      mii;
        struct ks8851_rxctrl    rxctrl;

        struct work_struct      tx_work;
        struct work_struct      irq_work;
        struct work_struct      rxctrl_work;

        struct sk_buff_head     txq;

        struct spi_message      spi_msg1;
        struct spi_message      spi_msg2;
        struct spi_transfer     spi_xfer1;
        struct spi_transfer     spi_xfer2[2];
};

static int msg_enable;

/* shift for byte-enable data */
#define BYTE_EN(_x)     ((_x) << 2)

/* turn register number and byte-enable mask into data for start of packet */
#define MK_OP(_byteen, _reg) (BYTE_EN(_byteen) | (_reg)  << (8+2) | (_reg) >> 6)

/* SPI register read/write calls.
 *
 * All these calls issue SPI transactions to access the chip's registers. They
 * all require that the necessary lock is held to prevent accesses when the
 * chip is busy transferring packet data (RX/TX FIFO accesses).
 */

/**
 * ks8851_wrreg16 - write 16bit register value to chip
 * @ks: The chip state
 * @reg: The register address
 * @val: The value to write
 *
 * Issue a write to put the value @val into the register specified in @reg.
 */
static void ks8851_wrreg16(struct ks8851_net *ks, unsigned reg, unsigned val)
{
        struct spi_transfer *xfer = &ks->spi_xfer1;
        struct spi_message *msg = &ks->spi_msg1;
        __le16 txb[2];
        int ret;

        txb[0] = cpu_to_le16(MK_OP(reg & 2 ? 0xC : 0x03, reg) | KS_SPIOP_WR);
        txb[1] = cpu_to_le16(val);

        xfer->tx_buf = txb;
        xfer->rx_buf = NULL;
        xfer->len = 4;

        ret = spi_sync(ks->spidev, msg);
        if (ret < 0)
                netdev_err(ks->netdev, "spi_sync() failed\n");
}

/**
 * ks8851_wrreg8 - write 8bit register value to chip
 * @ks: The chip state
 * @reg: The register address
 * @val: The value to write
 *
 * Issue a write to put the value @val into the register specified in @reg.
 */
static void ks8851_wrreg8(struct ks8851_net *ks, unsigned reg, unsigned val)
{
        struct spi_transfer *xfer = &ks->spi_xfer1;
        struct spi_message *msg = &ks->spi_msg1;
        __le16 txb[2];
        int ret;
        int bit;

        bit = 1 << (reg & 3);

        txb[0] = cpu_to_le16(MK_OP(bit, reg) | KS_SPIOP_WR);
        txb[1] = val;

        xfer->tx_buf = txb;
        xfer->rx_buf = NULL;
        xfer->len = 3;

        ret = spi_sync(ks->spidev, msg);
        if (ret < 0)
                netdev_err(ks->netdev, "spi_sync() failed\n");
}

/**
 * ks8851_rx_1msg - select whether to use one or two messages for spi read
 * @ks: The device structure
 *
 * Return whether to generate a single message with a tx and rx buffer
 * supplied to spi_sync(), or alternatively send the tx and rx buffers
 * as separate messages.
 *
 * Depending on the hardware in use, a single message may be more efficient
 * on interrupts or work done by the driver.
 *
 * This currently always returns true until we add some per-device data passed
 * from the platform code to specify which mode is better.
 */
static inline bool ks8851_rx_1msg(struct ks8851_net *ks)
{
        return true;
}

/**
 * ks8851_rdreg - issue read register command and return the data
 * @ks: The device state
 * @op: The register address and byte enables in message format.
 * @rxb: The RX buffer to return the result into
 * @rxl: The length of data expected.
 *
 * This is the low level read call that issues the necessary spi message(s)
 * to read data from the register specified in @op.
 */
static void ks8851_rdreg(struct ks8851_net *ks, unsigned op,
                         u8 *rxb, unsigned rxl)
{
        struct spi_transfer *xfer;
        struct spi_message *msg;
        __le16 *txb = (__le16 *)ks->txd;
        u8 *trx = ks->rxd;
        int ret;

        txb[0] = cpu_to_le16(op | KS_SPIOP_RD);

        if (ks8851_rx_1msg(ks)) {
                msg = &ks->spi_msg1;
                xfer = &ks->spi_xfer1;

                xfer->tx_buf = txb;
                xfer->rx_buf = trx;
                xfer->len = rxl + 2;
        } else {
                msg = &ks->spi_msg2;
                xfer = ks->spi_xfer2;

                xfer->tx_buf = txb;
                xfer->rx_buf = NULL;
                xfer->len = 2;

                xfer++;
                xfer->tx_buf = NULL;
                xfer->rx_buf = trx;
                xfer->len = rxl;
        }

        ret = spi_sync(ks->spidev, msg);
        if (ret < 0)
                netdev_err(ks->netdev, "read: spi_sync() failed\n");
        else if (ks8851_rx_1msg(ks))
                memcpy(rxb, trx + 2, rxl);
        else
                memcpy(rxb, trx, rxl);
}

/**
 * ks8851_rdreg8 - read 8 bit register from device
 * @ks: The chip information
 * @reg: The register address
 *
 * Read a 8bit register from the chip, returning the result
*/
static unsigned ks8851_rdreg8(struct ks8851_net *ks, unsigned reg)
{
        u8 rxb[1];

        ks8851_rdreg(ks, MK_OP(1 << (reg & 3), reg), rxb, 1);
        return rxb[0];
}

/**
 * ks8851_rdreg16 - read 16 bit register from device
 * @ks: The chip information
 * @reg: The register address
 *
 * Read a 16bit register from the chip, returning the result
*/
static unsigned ks8851_rdreg16(struct ks8851_net *ks, unsigned reg)
{
        __le16 rx = 0;

        ks8851_rdreg(ks, MK_OP(reg & 2 ? 0xC : 0x3, reg), (u8 *)&rx, 2);
        return le16_to_cpu(rx);
}

/**
 * ks8851_rdreg32 - read 32 bit register from device
 * @ks: The chip information
 * @reg: The register address
 *
 * Read a 32bit register from the chip.
 *
 * Note, this read requires the address be aligned to 4 bytes.
*/
static unsigned ks8851_rdreg32(struct ks8851_net *ks, unsigned reg)
{
        __le32 rx = 0;

        WARN_ON(reg & 3);

        ks8851_rdreg(ks, MK_OP(0xf, reg), (u8 *)&rx, 4);
        return le32_to_cpu(rx);
}

/**
 * ks8851_soft_reset - issue one of the soft reset to the device
 * @ks: The device state.
 * @op: The bit(s) to set in the GRR
 *
 * Issue the relevant soft-reset command to the device's GRR register
 * specified by @op.
 *
 * Note, the delays are in there as a caution to ensure that the reset
 * has time to take effect and then complete. Since the datasheet does
 * not currently specify the exact sequence, we have chosen something
 * that seems to work with our device.
 */
static void ks8851_soft_reset(struct ks8851_net *ks, unsigned op)
{
        ks8851_wrreg16(ks, KS_GRR, op);
        mdelay(1);      /* wait a short time to effect reset */
        ks8851_wrreg16(ks, KS_GRR, 0);
        mdelay(1);      /* wait for condition to clear */
}

/**
 * ks8851_write_mac_addr - write mac address to device registers
 * @dev: The network device
 *
 * Update the KS8851 MAC address registers from the address in @dev.
 *
 * This call assumes that the chip is not running, so there is no need to
 * shutdown the RXQ process whilst setting this.
*/
static int ks8851_write_mac_addr(struct net_device *dev)
{
        struct ks8851_net *ks = netdev_priv(dev);
        int i;

        mutex_lock(&ks->lock);

        for (i = 0; i < ETH_ALEN; i++)
                ks8851_wrreg8(ks, KS_MAR(i), dev->dev_addr[i]);

        mutex_unlock(&ks->lock);

        return 0;
}

/**
 * ks8851_init_mac - initialise the mac address
 * @ks: The device structure
 *
 * Get or create the initial mac address for the device and then set that
 * into the station address register. Currently we assume that the device
 * does not have a valid mac address in it, and so we use random_ether_addr()
 * to create a new one.
 *
 * In future, the driver should check to see if the device has an EEPROM
 * attached and whether that has a valid ethernet address in it.
 */
static void ks8851_init_mac(struct ks8851_net *ks)
{
        struct net_device *dev = ks->netdev;

        random_ether_addr(dev->dev_addr);
        ks8851_write_mac_addr(dev);
}

/**
 * ks8851_irq - device interrupt handler
 * @irq: Interrupt number passed from the IRQ hnalder.
 * @pw: The private word passed to register_irq(), our struct ks8851_net.
 *
 * Disable the interrupt from happening again until we've processed the
 * current status by scheduling ks8851_irq_work().
 */
static irqreturn_t ks8851_irq(int irq, void *pw)
{
        struct ks8851_net *ks = pw;

        disable_irq_nosync(irq);
        schedule_work(&ks->irq_work);
        return IRQ_HANDLED;
}

/**
 * ks8851_rdfifo - read data from the receive fifo
 * @ks: The device state.
 * @buff: The buffer address
 * @len: The length of the data to read
 *
 * Issue an RXQ FIFO read command and read the @len amount of data from
 * the FIFO into the buffer specified by @buff.
 */
static void ks8851_rdfifo(struct ks8851_net *ks, u8 *buff, unsigned len)
{
        struct spi_transfer *xfer = ks->spi_xfer2;
        struct spi_message *msg = &ks->spi_msg2;
        u8 txb[1];
        int ret;

        netif_dbg(ks, rx_status, ks->netdev,
                  "%s: %d@%p\n", __func__, len, buff);

        /* set the operation we're issuing */
        txb[0] = KS_SPIOP_RXFIFO;

        xfer->tx_buf = txb;
        xfer->rx_buf = NULL;
        xfer->len = 1;

        xfer++;
        xfer->rx_buf = buff;
        xfer->tx_buf = NULL;
        xfer->len = len;

        ret = spi_sync(ks->spidev, msg);
        if (ret < 0)
                netdev_err(ks->netdev, "%s: spi_sync() failed\n", __func__);
}

/**
 * ks8851_dbg_dumpkkt - dump initial packet contents to debug
 * @ks: The device state
 * @rxpkt: The data for the received packet
 *
 * Dump the initial data from the packet to dev_dbg().
*/
static void ks8851_dbg_dumpkkt(struct ks8851_net *ks, u8 *rxpkt)
{
        netdev_dbg(ks->netdev,
                   "pkt %02x%02x%02x%02x %02x%02x%02x%02x %02x%02x%02x%02x\n",
                   rxpkt[4], rxpkt[5], rxpkt[6], rxpkt[7],
                   rxpkt[8], rxpkt[9], rxpkt[10], rxpkt[11],
                   rxpkt[12], rxpkt[13], rxpkt[14], rxpkt[15]);
}

/**
 * ks8851_rx_pkts - receive packets from the host
 * @ks: The device information.
 *
 * This is called from the IRQ work queue when the system detects that there
 * are packets in the receive queue. Find out how many packets there are and
 * read them from the FIFO.
 */
static void ks8851_rx_pkts(struct ks8851_net *ks)
{
        struct sk_buff *skb;
        unsigned rxfc;
        unsigned rxlen;
        unsigned rxstat;
        u32 rxh;
        u8 *rxpkt;

        rxfc = ks8851_rdreg8(ks, KS_RXFC);

        netif_dbg(ks, rx_status, ks->netdev,
                  "%s: %d packets\n", __func__, rxfc);

        /* Currently we're issuing a read per packet, but we could possibly
         * improve the code by issuing a single read, getting the receive
         * header, allocating the packet and then reading the packet data
         * out in one go.
         *
         * This form of operation would require us to hold the SPI bus'
         * chipselect low during the entie transaction to avoid any
         * reset to the data stream coming from the chip.
         */

        for (; rxfc != 0; rxfc--) {
                rxh = ks8851_rdreg32(ks, KS_RXFHSR);
                rxstat = rxh & 0xffff;
                rxlen = rxh >> 16;

                netif_dbg(ks, rx_status, ks->netdev,
                          "rx: stat 0x%04x, len 0x%04x\n", rxstat, rxlen);

                /* the length of the packet includes the 32bit CRC */

                /* set dma read address */
                ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00);

                /* start the packet dma process, and set auto-dequeue rx */
                ks8851_wrreg16(ks, KS_RXQCR,
                               ks->rc_rxqcr | RXQCR_SDA | RXQCR_ADRFE);

                if (rxlen > 4) {
                        unsigned int rxalign;

                        rxlen -= 4;
                        rxalign = ALIGN(rxlen, 4);
                        skb = netdev_alloc_skb_ip_align(ks->netdev, rxalign);
                        if (skb) {

                                /* 4 bytes of status header + 4 bytes of
                                 * garbage: we put them before ethernet
                                 * header, so that they are copied,
                                 * but ignored.
                                 */

                                rxpkt = skb_put(skb, rxlen) - 8;

                                ks8851_rdfifo(ks, rxpkt, rxalign + 8);

                                if (netif_msg_pktdata(ks))
                                        ks8851_dbg_dumpkkt(ks, rxpkt);

                                skb->protocol = eth_type_trans(skb, ks->netdev);
                                netif_rx(skb);

                                ks->netdev->stats.rx_packets++;
                                ks->netdev->stats.rx_bytes += rxlen;
                        }
                }

                ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
        }
}

/**
 * ks8851_irq_work - work queue handler for dealing with interrupt requests
 * @work: The work structure that was scheduled by schedule_work()
 *
 * This is the handler invoked when the ks8851_irq() is called to find out
 * what happened, as we cannot allow ourselves to sleep whilst waiting for
 * anything other process has the chip's lock.
 *
 * Read the interrupt status, work out what needs to be done and then clear
 * any of the interrupts that are not needed.
 */
static void ks8851_irq_work(struct work_struct *work)
{
        struct ks8851_net *ks = container_of(work, struct ks8851_net, irq_work);
        unsigned status;
        unsigned handled = 0;

        mutex_lock(&ks->lock);

        status = ks8851_rdreg16(ks, KS_ISR);

        netif_dbg(ks, intr, ks->netdev,
                  "%s: status 0x%04x\n", __func__, status);

        if (status & IRQ_LCI) {
                /* should do something about checking link status */
                handled |= IRQ_LCI;
        }

        if (status & IRQ_LDI) {
                u16 pmecr = ks8851_rdreg16(ks, KS_PMECR);
                pmecr &= ~PMECR_WKEVT_MASK;
                ks8851_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK);

                handled |= IRQ_LDI;
        }

        if (status & IRQ_RXPSI)
                handled |= IRQ_RXPSI;

        if (status & IRQ_TXI) {
                handled |= IRQ_TXI;

                /* no lock here, tx queue should have been stopped */

                /* update our idea of how much tx space is available to the
                 * system */
                ks->tx_space = ks8851_rdreg16(ks, KS_TXMIR);

                netif_dbg(ks, intr, ks->netdev,
                          "%s: txspace %d\n", __func__, ks->tx_space);
        }

        if (status & IRQ_RXI)
                handled |= IRQ_RXI;

        if (status & IRQ_SPIBEI) {
                dev_err(&ks->spidev->dev, "%s: spi bus error\n", __func__);
                handled |= IRQ_SPIBEI;
        }

        ks8851_wrreg16(ks, KS_ISR, handled);

        if (status & IRQ_RXI) {
                /* the datasheet says to disable the rx interrupt during
                 * packet read-out, however we're masking the interrupt
                 * from the device so do not bother masking just the RX
                 * from the device. */

                ks8851_rx_pkts(ks);
        }

        /* if something stopped the rx process, probably due to wanting
         * to change the rx settings, then do something about restarting
         * it. */
        if (status & IRQ_RXPSI) {
                struct ks8851_rxctrl *rxc = &ks->rxctrl;

                /* update the multicast hash table */
                ks8851_wrreg16(ks, KS_MAHTR0, rxc->mchash[0]);
                ks8851_wrreg16(ks, KS_MAHTR1, rxc->mchash[1]);
                ks8851_wrreg16(ks, KS_MAHTR2, rxc->mchash[2]);
                ks8851_wrreg16(ks, KS_MAHTR3, rxc->mchash[3]);

                ks8851_wrreg16(ks, KS_RXCR2, rxc->rxcr2);
                ks8851_wrreg16(ks, KS_RXCR1, rxc->rxcr1);
        }

        mutex_unlock(&ks->lock);

        if (status & IRQ_TXI)
                netif_wake_queue(ks->netdev);

        enable_irq(ks->netdev->irq);
}

/**
 * calc_txlen - calculate size of message to send packet
 * @len: Length of data
 *
 * Returns the size of the TXFIFO message needed to send
 * this packet.
 */
static inline unsigned calc_txlen(unsigned len)
{
        return ALIGN(len + 4, 4);
}

/**
 * ks8851_wrpkt - write packet to TX FIFO
 * @ks: The device state.
 * @txp: The sk_buff to transmit.
 * @irq: IRQ on completion of the packet.
 *
 * Send the @txp to the chip. This means creating the relevant packet header
 * specifying the length of the packet and the other information the chip
 * needs, such as IRQ on completion. Send the header and the packet data to
 * the device.
 */
static void ks8851_wrpkt(struct ks8851_net *ks, struct sk_buff *txp, bool irq)
{
        struct spi_transfer *xfer = ks->spi_xfer2;
        struct spi_message *msg = &ks->spi_msg2;
        unsigned fid = 0;
        int ret;

        netif_dbg(ks, tx_queued, ks->netdev, "%s: skb %p, %d@%p, irq %d\n",
                  __func__, txp, txp->len, txp->data, irq);

        fid = ks->fid++;
        fid &= TXFR_TXFID_MASK;

        if (irq)
                fid |= TXFR_TXIC;       /* irq on completion */

        /* start header at txb[1] to align txw entries */
        ks->txh.txb[1] = KS_SPIOP_TXFIFO;
        ks->txh.txw[1] = cpu_to_le16(fid);
        ks->txh.txw[2] = cpu_to_le16(txp->len);

        xfer->tx_buf = &ks->txh.txb[1];
        xfer->rx_buf = NULL;
        xfer->len = 5;

        xfer++;
        xfer->tx_buf = txp->data;
        xfer->rx_buf = NULL;
        xfer->len = ALIGN(txp->len, 4);

        ret = spi_sync(ks->spidev, msg);
        if (ret < 0)
                netdev_err(ks->netdev, "%s: spi_sync() failed\n", __func__);
}

/**
 * ks8851_done_tx - update and then free skbuff after transmitting
 * @ks: The device state
 * @txb: The buffer transmitted
 */
static void ks8851_done_tx(struct ks8851_net *ks, struct sk_buff *txb)
{
        struct net_device *dev = ks->netdev;

        dev->stats.tx_bytes += txb->len;
        dev->stats.tx_packets++;

        dev_kfree_skb(txb);
}

/**
 * ks8851_tx_work - process tx packet(s)
 * @work: The work strucutre what was scheduled.
 *
 * This is called when a number of packets have been scheduled for
 * transmission and need to be sent to the device.
 */
static void ks8851_tx_work(struct work_struct *work)
{
        struct ks8851_net *ks = container_of(work, struct ks8851_net, tx_work);
        struct sk_buff *txb;
        bool last = skb_queue_empty(&ks->txq);

        mutex_lock(&ks->lock);

        while (!last) {
                txb = skb_dequeue(&ks->txq);
                last = skb_queue_empty(&ks->txq);

                if (txb != NULL) {
                        ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA);
                        ks8851_wrpkt(ks, txb, last);
                        ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
                        ks8851_wrreg16(ks, KS_TXQCR, TXQCR_METFE);

                        ks8851_done_tx(ks, txb);
                }
        }

        mutex_unlock(&ks->lock);
}

/**
 * ks8851_set_powermode - set power mode of the device
 * @ks: The device state
 * @pwrmode: The power mode value to write to KS_PMECR.
 *
 * Change the power mode of the chip.
 */
static void ks8851_set_powermode(struct ks8851_net *ks, unsigned pwrmode)
{
        unsigned pmecr;

        netif_dbg(ks, hw, ks->netdev, "setting power mode %d\n", pwrmode);

        pmecr = ks8851_rdreg16(ks, KS_PMECR);
        pmecr &= ~PMECR_PM_MASK;
        pmecr |= pwrmode;

        ks8851_wrreg16(ks, KS_PMECR, pmecr);
}

/**
 * ks8851_net_open - open network device
 * @dev: The network device being opened.
 *
 * Called when the network device is marked active, such as a user executing
 * 'ifconfig up' on the device.
 */
static int ks8851_net_open(struct net_device *dev)
{
        struct ks8851_net *ks = netdev_priv(dev);

        /* lock the card, even if we may not actually be doing anything
         * else at the moment */
        mutex_lock(&ks->lock);

        netif_dbg(ks, ifup, ks->netdev, "opening\n");

        /* bring chip out of any power saving mode it was in */
        ks8851_set_powermode(ks, PMECR_PM_NORMAL);

        /* issue a soft reset to the RX/TX QMU to put it into a known
         * state. */
        ks8851_soft_reset(ks, GRR_QMU);

        /* setup transmission parameters */

        ks8851_wrreg16(ks, KS_TXCR, (TXCR_TXE | /* enable transmit process */
                                     TXCR_TXPE | /* pad to min length */
                                     TXCR_TXCRC | /* add CRC */
                                     TXCR_TXFCE)); /* enable flow control */

        /* auto-increment tx data, reset tx pointer */
        ks8851_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI);

        /* setup receiver control */

        ks8851_wrreg16(ks, KS_RXCR1, (RXCR1_RXPAFMA | /*  from mac filter */
                                      RXCR1_RXFCE | /* enable flow control */
                                      RXCR1_RXBE | /* broadcast enable */
                                      RXCR1_RXUE | /* unicast enable */
                                      RXCR1_RXE)); /* enable rx block */

        /* transfer entire frames out in one go */
        ks8851_wrreg16(ks, KS_RXCR2, RXCR2_SRDBL_FRAME);

        /* set receive counter timeouts */
        ks8851_wrreg16(ks, KS_RXDTTR, 1000); /* 1ms after first frame to IRQ */
        ks8851_wrreg16(ks, KS_RXDBCTR, 4096); /* >4Kbytes in buffer to IRQ */
        ks8851_wrreg16(ks, KS_RXFCTR, 10);  /* 10 frames to IRQ */

        ks->rc_rxqcr = (RXQCR_RXFCTE |  /* IRQ on frame count exceeded */
                        RXQCR_RXDBCTE | /* IRQ on byte count exceeded */
                        RXQCR_RXDTTE);  /* IRQ on time exceeded */

        ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);

        /* clear then enable interrupts */

#define STD_IRQ (IRQ_LCI |      /* Link Change */       \
                 IRQ_TXI |      /* TX done */           \
                 IRQ_RXI |      /* RX done */           \
                 IRQ_SPIBEI |   /* SPI bus error */     \
                 IRQ_TXPSI |    /* TX process stop */   \
                 IRQ_RXPSI)     /* RX process stop */

        ks->rc_ier = STD_IRQ;
        ks8851_wrreg16(ks, KS_ISR, STD_IRQ);
        ks8851_wrreg16(ks, KS_IER, STD_IRQ);

        netif_start_queue(ks->netdev);

        netif_dbg(ks, ifup, ks->netdev, "network device up\n");

        mutex_unlock(&ks->lock);
        return 0;
}

/**
 * ks8851_net_stop - close network device
 * @dev: The device being closed.
 *
 * Called to close down a network device which has been active. Cancell any
 * work, shutdown the RX and TX process and then place the chip into a low
 * power state whilst it is not being used.
 */
static int ks8851_net_stop(struct net_device *dev)
{
        struct ks8851_net *ks = netdev_priv(dev);

        netif_info(ks, ifdown, dev, "shutting down\n");

        netif_stop_queue(dev);

        mutex_lock(&ks->lock);

        /* stop any outstanding work */
        flush_work(&ks->irq_work);
        flush_work(&ks->tx_work);
        flush_work(&ks->rxctrl_work);

        /* turn off the IRQs and ack any outstanding */
        ks8851_wrreg16(ks, KS_IER, 0x0000);
        ks8851_wrreg16(ks, KS_ISR, 0xffff);

        /* shutdown RX process */
        ks8851_wrreg16(ks, KS_RXCR1, 0x0000);

        /* shutdown TX process */
        ks8851_wrreg16(ks, KS_TXCR, 0x0000);

        /* set powermode to soft power down to save power */
        ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN);

        /* ensure any queued tx buffers are dumped */
        while (!skb_queue_empty(&ks->txq)) {
                struct sk_buff *txb = skb_dequeue(&ks->txq);

                netif_dbg(ks, ifdown, ks->netdev,
                          "%s: freeing txb %p\n", __func__, txb);

                dev_kfree_skb(txb);
        }

        mutex_unlock(&ks->lock);
        return 0;
}

/**
 * ks8851_start_xmit - transmit packet
 * @skb: The buffer to transmit
 * @dev: The device used to transmit the packet.
 *
 * Called by the network layer to transmit the @skb. Queue the packet for
 * the device and schedule the necessary work to transmit the packet when
 * it is free.
 *
 * We do this to firstly avoid sleeping with the network device locked,
 * and secondly so we can round up more than one packet to transmit which
 * means we can try and avoid generating too many transmit done interrupts.
 */
static netdev_tx_t ks8851_start_xmit(struct sk_buff *skb,
                                     struct net_device *dev)
{
        struct ks8851_net *ks = netdev_priv(dev);
        unsigned needed = calc_txlen(skb->len);
        netdev_tx_t ret = NETDEV_TX_OK;

        netif_dbg(ks, tx_queued, ks->netdev,
                  "%s: skb %p, %d@%p\n", __func__, skb, skb->len, skb->data);

        spin_lock(&ks->statelock);

        if (needed > ks->tx_space) {
                netif_stop_queue(dev);
                ret = NETDEV_TX_BUSY;
        } else {
                ks->tx_space -= needed;
                skb_queue_tail(&ks->txq, skb);
        }

        spin_unlock(&ks->statelock);
        schedule_work(&ks->tx_work);

        return ret;
}

/**
 * ks8851_rxctrl_work - work handler to change rx mode
 * @work: The work structure this belongs to.
 *
 * Lock the device and issue the necessary changes to the receive mode from
 * the network device layer. This is done so that we can do this without
 * having to sleep whilst holding the network device lock.
 *
 * Since the recommendation from Micrel is that the RXQ is shutdown whilst the
 * receive parameters are programmed, we issue a write to disable the RXQ and
 * then wait for the interrupt handler to be triggered once the RXQ shutdown is
 * complete. The interrupt handler then writes the new values into the chip.
 */
static void ks8851_rxctrl_work(struct work_struct *work)
{
        struct ks8851_net *ks = container_of(work, struct ks8851_net, rxctrl_work);

        mutex_lock(&ks->lock);

        /* need to shutdown RXQ before modifying filter parameters */
        ks8851_wrreg16(ks, KS_RXCR1, 0x00);

        mutex_unlock(&ks->lock);
}

static void ks8851_set_rx_mode(struct net_device *dev)
{
        struct ks8851_net *ks = netdev_priv(dev);
        struct ks8851_rxctrl rxctrl;

        memset(&rxctrl, 0, sizeof(rxctrl));

        if (dev->flags & IFF_PROMISC) {
                /* interface to receive everything */

                rxctrl.rxcr1 = RXCR1_RXAE | RXCR1_RXINVF;
        } else if (dev->flags & IFF_ALLMULTI) {
                /* accept all multicast packets */

                rxctrl.rxcr1 = (RXCR1_RXME | RXCR1_RXAE |
                                RXCR1_RXPAFMA | RXCR1_RXMAFMA);
        } else if (dev->flags & IFF_MULTICAST && !netdev_mc_empty(dev)) {
                struct netdev_hw_addr *ha;
                u32 crc;

                /* accept some multicast */

                netdev_for_each_mc_addr(ha, dev) {
                        crc = ether_crc(ETH_ALEN, ha->addr);
                        crc >>= (32 - 6);  /* get top six bits */

                        rxctrl.mchash[crc >> 4] |= (1 << (crc & 0xf));
                }

                rxctrl.rxcr1 = RXCR1_RXME | RXCR1_RXPAFMA;
        } else {
                /* just accept broadcast / unicast */
                rxctrl.rxcr1 = RXCR1_RXPAFMA;
        }

        rxctrl.rxcr1 |= (RXCR1_RXUE | /* unicast enable */
                         RXCR1_RXBE | /* broadcast enable */
                         RXCR1_RXE | /* RX process enable */
                         RXCR1_RXFCE); /* enable flow control */

        rxctrl.rxcr2 |= RXCR2_SRDBL_FRAME;

        /* schedule work to do the actual set of the data if needed */

        spin_lock(&ks->statelock);

        if (memcmp(&rxctrl, &ks->rxctrl, sizeof(rxctrl)) != 0) {
                memcpy(&ks->rxctrl, &rxctrl, sizeof(ks->rxctrl));
                schedule_work(&ks->rxctrl_work);
        }

        spin_unlock(&ks->statelock);
}

static int ks8851_set_mac_address(struct net_device *dev, void *addr)
{
        struct sockaddr *sa = addr;

        if (netif_running(dev))
                return -EBUSY;

        if (!is_valid_ether_addr(sa->sa_data))
                return -EADDRNOTAVAIL;

        memcpy(dev->dev_addr, sa->sa_data, ETH_ALEN);
        return ks8851_write_mac_addr(dev);
}

static int ks8851_net_ioctl(struct net_device *dev, struct ifreq *req, int cmd)
{
        struct ks8851_net *ks = netdev_priv(dev);

        if (!netif_running(dev))
                return -EINVAL;

        return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL);
}

static const struct net_device_ops ks8851_netdev_ops = {
        .ndo_open               = ks8851_net_open,
        .ndo_stop               = ks8851_net_stop,
        .ndo_do_ioctl           = ks8851_net_ioctl,
        .ndo_start_xmit         = ks8851_start_xmit,
        .ndo_set_mac_address    = ks8851_set_mac_address,
        .ndo_set_rx_mode        = ks8851_set_rx_mode,
        .ndo_change_mtu         = eth_change_mtu,
        .ndo_validate_addr      = eth_validate_addr,
};

/* Companion eeprom access */

enum {  /* EEPROM programming states */
        EEPROM_CONTROL,
        EEPROM_ADDRESS,
        EEPROM_DATA,
        EEPROM_COMPLETE
};

/**
 * ks8851_eeprom_read - read a 16bits word in ks8851 companion EEPROM
 * @dev: The network device the PHY is on.
 * @addr: EEPROM address to read
 *
 * eeprom_size: used to define the data coding length. Can be changed
 * through debug-fs.
 *
 * Programs a read on the EEPROM using ks8851 EEPROM SW access feature.
 * Warning: The READ feature is not supported on ks8851 revision 0.
 *
 * Rough programming model:
 *  - on period start: set clock high and read value on bus
 *  - on period / 2: set clock low and program value on bus
 *  - start on period / 2
 */
unsigned int ks8851_eeprom_read(struct net_device *dev, unsigned int addr)
{
        struct ks8851_net *ks = netdev_priv(dev);
        int eepcr;
        int ctrl = EEPROM_OP_READ;
        int state = EEPROM_CONTROL;
        int bit_count = EEPROM_OP_LEN - 1;
        unsigned int data = 0;
        int dummy;
        unsigned int addr_len;

        addr_len = (ks->eeprom_size == 128) ? 6 : 8;

        /* start transaction: chip select high, authorize write */
        mutex_lock(&ks->lock);
        eepcr = EEPCR_EESA | EEPCR_EESRWA;
        ks8851_wrreg16(ks, KS_EEPCR, eepcr);
        eepcr |= EEPCR_EECS;
        ks8851_wrreg16(ks, KS_EEPCR, eepcr);
        mutex_unlock(&ks->lock);

        while (state != EEPROM_COMPLETE) {
                /* falling clock period starts... */
                /* set EED_IO pin for control and address */
                eepcr &= ~EEPCR_EEDO;
                switch (state) {
                case EEPROM_CONTROL:
                        eepcr |= ((ctrl >> bit_count) & 1) << 2;
                        if (bit_count-- <= 0) {
                                bit_count = addr_len - 1;
                                state = EEPROM_ADDRESS;
                        }
                        break;
                case EEPROM_ADDRESS:
                        eepcr |= ((addr >> bit_count) & 1) << 2;
                        bit_count--;
                        break;
                case EEPROM_DATA:
                        /* Change to receive mode */
                        eepcr &= ~EEPCR_EESRWA;
                        break;
                }

                /* lower clock  */
                eepcr &= ~EEPCR_EESCK;

                mutex_lock(&ks->lock);
                ks8851_wrreg16(ks, KS_EEPCR, eepcr);
                mutex_unlock(&ks->lock);

                /* waitread period / 2 */
                udelay(EEPROM_SK_PERIOD / 2);

                /* rising clock period starts... */

                /* raise clock */
                mutex_lock(&ks->lock);
                eepcr |= EEPCR_EESCK;
                ks8851_wrreg16(ks, KS_EEPCR, eepcr);
                mutex_unlock(&ks->lock);

                /* Manage read */
                switch (state) {
                case EEPROM_ADDRESS:
                        if (bit_count < 0) {
                                bit_count = EEPROM_DATA_LEN - 1;
                                state = EEPROM_DATA;
                        }
                        break;
                case EEPROM_DATA:
                        mutex_lock(&ks->lock);
                        dummy = ks8851_rdreg16(ks, KS_EEPCR);
                        mutex_unlock(&ks->lock);
                        data |= ((dummy >> EEPCR_EESB_OFFSET) & 1) << bit_count;
                        if (bit_count-- <= 0)
                                state = EEPROM_COMPLETE;
                        break;
                }

                /* wait period / 2 */
                udelay(EEPROM_SK_PERIOD / 2);
        }

        /* close transaction */
        mutex_lock(&ks->lock);
        eepcr &= ~EEPCR_EECS;
        ks8851_wrreg16(ks, KS_EEPCR, eepcr);
        eepcr = 0;
        ks8851_wrreg16(ks, KS_EEPCR, eepcr);
        mutex_unlock(&ks->lock);

        return data;
}

/**
 * ks8851_eeprom_write - write a 16bits word in ks8851 companion EEPROM
 * @dev: The network device the PHY is on.
 * @op: operand (can be WRITE, EWEN, EWDS)
 * @addr: EEPROM address to write
 * @data: data to write
 *
 * eeprom_size: used to define the data coding length. Can be changed
 * through debug-fs.
 *
 * Programs a write on the EEPROM using ks8851 EEPROM SW access feature.
 *
 * Note that a write enable is required before writing data.
 *
 * Rough programming model:
 *  - on period start: set clock high
 *  - on period / 2: set clock low and program value on bus
 *  - start on period / 2
 */
void ks8851_eeprom_write(struct net_device *dev, unsigned int op,
                                        unsigned int addr, unsigned int data)
{
        struct ks8851_net *ks = netdev_priv(dev);
        int eepcr;
        int state = EEPROM_CONTROL;
        int bit_count = EEPROM_OP_LEN - 1;
        unsigned int addr_len;

        addr_len = (ks->eeprom_size == 128) ? 6 : 8;

        switch (op) {
        case EEPROM_OP_EWEN:
                addr = 0x30;
        break;
        case EEPROM_OP_EWDS:
                addr = 0;
                break;
        }

        /* start transaction: chip select high, authorize write */
        mutex_lock(&ks->lock);
        eepcr = EEPCR_EESA | EEPCR_EESRWA;
        ks8851_wrreg16(ks, KS_EEPCR, eepcr);
        eepcr |= EEPCR_EECS;
        ks8851_wrreg16(ks, KS_EEPCR, eepcr);
        mutex_unlock(&ks->lock);

        while (state != EEPROM_COMPLETE) {
                /* falling clock period starts... */
                /* set EED_IO pin for control and address */
                eepcr &= ~EEPCR_EEDO;
                switch (state) {
                case EEPROM_CONTROL:
                        eepcr |= ((op >> bit_count) & 1) << 2;
                        if (bit_count-- <= 0) {
                                bit_count = addr_len - 1;
                                state = EEPROM_ADDRESS;
                        }
                        break;
                case EEPROM_ADDRESS:
                        eepcr |= ((addr >> bit_count) & 1) << 2;
                        if (bit_count-- <= 0) {
                                if (op == EEPROM_OP_WRITE) {
                                        bit_count = EEPROM_DATA_LEN - 1;
                                        state = EEPROM_DATA;
                                } else {
                                        state = EEPROM_COMPLETE;
                                }
                        }
                        break;
                case EEPROM_DATA:
                        eepcr |= ((data >> bit_count) & 1) << 2;
                        if (bit_count-- <= 0)
                                state = EEPROM_COMPLETE;
                        break;
                }

                /* lower clock  */
                eepcr &= ~EEPCR_EESCK;

                mutex_lock(&ks->lock);
                ks8851_wrreg16(ks, KS_EEPCR, eepcr);
                mutex_unlock(&ks->lock);

                /* wait period / 2 */
                udelay(EEPROM_SK_PERIOD / 2);

                /* rising clock period starts... */

                /* raise clock */
                eepcr |= EEPCR_EESCK;
                mutex_lock(&ks->lock);
                ks8851_wrreg16(ks, KS_EEPCR, eepcr);
                mutex_unlock(&ks->lock);

                /* wait period / 2 */
                udelay(EEPROM_SK_PERIOD / 2);
        }

        /* close transaction */
        mutex_lock(&ks->lock);
        eepcr &= ~EEPCR_EECS;
        ks8851_wrreg16(ks, KS_EEPCR, eepcr);
        eepcr = 0;
        ks8851_wrreg16(ks, KS_EEPCR, eepcr);
        mutex_unlock(&ks->lock);

}

/* ethtool support */

static void ks8851_get_drvinfo(struct net_device *dev,
                               struct ethtool_drvinfo *di)
{
        strlcpy(di->driver, "KS8851", sizeof(di->driver));
        strlcpy(di->version, "1.00", sizeof(di->version));
        strlcpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info));
}

static u32 ks8851_get_msglevel(struct net_device *dev)
{
        struct ks8851_net *ks = netdev_priv(dev);
        return ks->msg_enable;
}

static void ks8851_set_msglevel(struct net_device *dev, u32 to)
{
        struct ks8851_net *ks = netdev_priv(dev);
        ks->msg_enable = to;
}

static int ks8851_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
        struct ks8851_net *ks = netdev_priv(dev);
        return mii_ethtool_gset(&ks->mii, cmd);
}

static int ks8851_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
        struct ks8851_net *ks = netdev_priv(dev);
        return mii_ethtool_sset(&ks->mii, cmd);
}

static u32 ks8851_get_link(struct net_device *dev)
{
        struct ks8851_net *ks = netdev_priv(dev);
        return mii_link_ok(&ks->mii);
}

static int ks8851_nway_reset(struct net_device *dev)
{
        struct ks8851_net *ks = netdev_priv(dev);
        return mii_nway_restart(&ks->mii);
}

static int ks8851_get_eeprom_len(struct net_device *dev)
{
        struct ks8851_net *ks = netdev_priv(dev);
        return ks->eeprom_size;
}

static int ks8851_get_eeprom(struct net_device *dev,
                            struct ethtool_eeprom *eeprom, u8 *bytes)
{
        struct ks8851_net *ks = netdev_priv(dev);
        u16 *eeprom_buff;
        int first_word;
        int last_word;
        int ret_val = 0;
        u16 i;

        if (eeprom->len == 0)
                return -EINVAL;

        if (eeprom->len > ks->eeprom_size)
                return -EINVAL;

        eeprom->magic = ks8851_rdreg16(ks, KS_CIDER);

        first_word = eeprom->offset >> 1;
        last_word = (eeprom->offset + eeprom->len - 1) >> 1;

        eeprom_buff = kmalloc(sizeof(u16) *
                        (last_word - first_word + 1), GFP_KERNEL);
        if (!eeprom_buff)
                return -ENOMEM;

        for (i = 0; i < last_word - first_word + 1; i++)
                eeprom_buff[i] = ks8851_eeprom_read(dev, first_word + 1);

        /* Device's eeprom is little-endian, word addressable */
        for (i = 0; i < last_word - first_word + 1; i++)
                le16_to_cpus(&eeprom_buff[i]);

        memcpy(bytes, (u8 *)eeprom_buff + (eeprom->offset & 1), eeprom->len);
        kfree(eeprom_buff);

        return ret_val;
}

static int ks8851_set_eeprom(struct net_device *dev,
                            struct ethtool_eeprom *eeprom, u8 *bytes)
{
        struct ks8851_net *ks = netdev_priv(dev);
        u16 *eeprom_buff;
        void *ptr;
        int max_len;
        int first_word;
        int last_word;
        int ret_val = 0;
        u16 i;

        if (eeprom->len == 0)
                return -EOPNOTSUPP;

        if (eeprom->len > ks->eeprom_size)
                return -EINVAL;

        if (eeprom->magic != ks8851_rdreg16(ks, KS_CIDER))
                return -EFAULT;

        first_word = eeprom->offset >> 1;
        last_word = (eeprom->offset + eeprom->len - 1) >> 1;
        max_len = (last_word - first_word + 1) * 2;
        eeprom_buff = kmalloc(max_len, GFP_KERNEL);
        if (!eeprom_buff)
                return -ENOMEM;

        ptr = (void *)eeprom_buff;

        if (eeprom->offset & 1) {
                /* need read/modify/write of first changed EEPROM word */
                /* only the second byte of the word is being modified */
                eeprom_buff[0] = ks8851_eeprom_read(dev, first_word);
                ptr++;
        }
        if ((eeprom->offset + eeprom->len) & 1)
                /* need read/modify/write of last changed EEPROM word */
                /* only the first byte of the word is being modified */
                eeprom_buff[last_word - first_word] =
                                        ks8851_eeprom_read(dev, last_word);


        /* Device's eeprom is little-endian, word addressable */
        le16_to_cpus(&eeprom_buff[0]);
        le16_to_cpus(&eeprom_buff[last_word - first_word]);

        memcpy(ptr, bytes, eeprom->len);

        for (i = 0; i < last_word - first_word + 1; i++)
                eeprom_buff[i] = cpu_to_le16(eeprom_buff[i]);

        ks8851_eeprom_write(dev, EEPROM_OP_EWEN, 0, 0);

        for (i = 0; i < last_word - first_word + 1; i++) {
                ks8851_eeprom_write(dev, EEPROM_OP_WRITE, first_word + i,
                                                        eeprom_buff[i]);
                mdelay(EEPROM_WRITE_TIME);
        }

        ks8851_eeprom_write(dev, EEPROM_OP_EWDS, 0, 0);

        kfree(eeprom_buff);
        return ret_val;
}

static const struct ethtool_ops ks8851_ethtool_ops = {
        .get_drvinfo    = ks8851_get_drvinfo,
        .get_msglevel   = ks8851_get_msglevel,
        .set_msglevel   = ks8851_set_msglevel,
        .get_settings   = ks8851_get_settings,
        .set_settings   = ks8851_set_settings,
        .get_link       = ks8851_get_link,
        .nway_reset     = ks8851_nway_reset,
        .get_eeprom_len = ks8851_get_eeprom_len,
        .get_eeprom     = ks8851_get_eeprom,
        .set_eeprom     = ks8851_set_eeprom,
};

/* MII interface controls */

/**
 * ks8851_phy_reg - convert MII register into a KS8851 register
 * @reg: MII register number.
 *
 * Return the KS8851 register number for the corresponding MII PHY register
 * if possible. Return zero if the MII register has no direct mapping to the
 * KS8851 register set.
 */
static int ks8851_phy_reg(int reg)
{
        switch (reg) {
        case MII_BMCR:
                return KS_P1MBCR;
        case MII_BMSR:
                return KS_P1MBSR;
        case MII_PHYSID1:
                return KS_PHY1ILR;
        case MII_PHYSID2:
                return KS_PHY1IHR;
        case MII_ADVERTISE:
                return KS_P1ANAR;
        case MII_LPA:
                return KS_P1ANLPR;
        }

        return 0x0;
}

/**
 * ks8851_phy_read - MII interface PHY register read.
 * @dev: The network device the PHY is on.
 * @phy_addr: Address of PHY (ignored as we only have one)
 * @reg: The register to read.
 *
 * This call reads data from the PHY register specified in @reg. Since the
 * device does not support all the MII registers, the non-existent values
 * are always returned as zero.
 *
 * We return zero for unsupported registers as the MII code does not check
 * the value returned for any error status, and simply returns it to the
 * caller. The mii-tool that the driver was tested with takes any -ve error
 * as real PHY capabilities, thus displaying incorrect data to the user.
 */
static int ks8851_phy_read(struct net_device *dev, int phy_addr, int reg)
{
        struct ks8851_net *ks = netdev_priv(dev);
        int ksreg;
        int result;

        ksreg = ks8851_phy_reg(reg);
        if (!ksreg)
                return 0x0;     /* no error return allowed, so use zero */

        mutex_lock(&ks->lock);
        result = ks8851_rdreg16(ks, ksreg);
        mutex_unlock(&ks->lock);

        return result;
}

static void ks8851_phy_write(struct net_device *dev,
                             int phy, int reg, int value)
{
        struct ks8851_net *ks = netdev_priv(dev);
        int ksreg;

        ksreg = ks8851_phy_reg(reg);
        if (ksreg) {
                mutex_lock(&ks->lock);
                ks8851_wrreg16(ks, ksreg, value);
                mutex_unlock(&ks->lock);
        }
}

/**
 * ks8851_read_selftest - read the selftest memory info.
 * @ks: The device state
 *
 * Read and check the TX/RX memory selftest information.
 */
static int ks8851_read_selftest(struct ks8851_net *ks)
{
        unsigned both_done = MBIR_TXMBF | MBIR_RXMBF;
        int ret = 0;
        unsigned rd;

        rd = ks8851_rdreg16(ks, KS_MBIR);

        if ((rd & both_done) != both_done) {
                netdev_warn(ks->netdev, "Memory selftest not finished\n");
                return 0;
        }

        if (rd & MBIR_TXMBFA) {
                netdev_err(ks->netdev, "TX memory selftest fail\n");
                ret |= 1;
        }

        if (rd & MBIR_RXMBFA) {
                netdev_err(ks->netdev, "RX memory selftest fail\n");
                ret |= 2;
        }

        return 0;
}

/* driver bus management functions */

#ifdef CONFIG_PM
static int ks8851_suspend(struct spi_device *spi, pm_message_t state)
{
        struct ks8851_net *ks = dev_get_drvdata(&spi->dev);
        struct net_device *dev = ks->netdev;

        if (netif_running(dev)) {
                netif_device_detach(dev);
                ks8851_net_stop(dev);
        }

        return 0;
}

static int ks8851_resume(struct spi_device *spi)
{
        struct ks8851_net *ks = dev_get_drvdata(&spi->dev);
        struct net_device *dev = ks->netdev;

        if (netif_running(dev)) {
                ks8851_net_open(dev);
                netif_device_attach(dev);
        }

        return 0;
}
#else
#define ks8851_suspend NULL
#define ks8851_resume NULL
#endif

static int __devinit ks8851_probe(struct spi_device *spi)
{
        struct net_device *ndev;
        struct ks8851_net *ks;
        int ret;

        ndev = alloc_etherdev(sizeof(struct ks8851_net));
        if (!ndev) {
                dev_err(&spi->dev, "failed to alloc ethernet device\n");
                return -ENOMEM;
        }

        spi->bits_per_word = 8;

        ks = netdev_priv(ndev);

        ks->netdev = ndev;
        ks->spidev = spi;
        ks->tx_space = 6144;

        mutex_init(&ks->lock);
        spin_lock_init(&ks->statelock);

        INIT_WORK(&ks->tx_work, ks8851_tx_work);
        INIT_WORK(&ks->irq_work, ks8851_irq_work);
        INIT_WORK(&ks->rxctrl_work, ks8851_rxctrl_work);

        /* initialise pre-made spi transfer messages */

        spi_message_init(&ks->spi_msg1);
        spi_message_add_tail(&ks->spi_xfer1, &ks->spi_msg1);

        spi_message_init(&ks->spi_msg2);
        spi_message_add_tail(&ks->spi_xfer2[0], &ks->spi_msg2);
        spi_message_add_tail(&ks->spi_xfer2[1], &ks->spi_msg2);

        /* setup mii state */
        ks->mii.dev             = ndev;
        ks->mii.phy_id          = 1,
        ks->mii.phy_id_mask     = 1;
        ks->mii.reg_num_mask    = 0xf;
        ks->mii.mdio_read       = ks8851_phy_read;
        ks->mii.mdio_write      = ks8851_phy_write;

        dev_info(&spi->dev, "message enable is %d\n", msg_enable);

        /* set the default message enable */
        ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV |
                                                     NETIF_MSG_PROBE |
                                                     NETIF_MSG_LINK));

        skb_queue_head_init(&ks->txq);

        SET_ETHTOOL_OPS(ndev, &ks8851_ethtool_ops);
        SET_NETDEV_DEV(ndev, &spi->dev);

        dev_set_drvdata(&spi->dev, ks);

        ndev->if_port = IF_PORT_100BASET;
        ndev->netdev_ops = &ks8851_netdev_ops;
        ndev->irq = spi->irq;

        /* issue a global soft reset to reset the device. */
        ks8851_soft_reset(ks, GRR_GSR);

        /* simple check for a valid chip being connected to the bus */

        if ((ks8851_rdreg16(ks, KS_CIDER) & ~CIDER_REV_MASK) != CIDER_ID) {
                dev_err(&spi->dev, "failed to read device ID\n");
                ret = -ENODEV;
                goto err_id;
        }

        /* cache the contents of the CCR register for EEPROM, etc. */
        ks->rc_ccr = ks8851_rdreg16(ks, KS_CCR);

        if (ks->rc_ccr & CCR_EEPROM)
                ks->eeprom_size = 128;
        else
                ks->eeprom_size = 0;

        ks8851_read_selftest(ks);
        ks8851_init_mac(ks);

        ret = request_irq(spi->irq, ks8851_irq, IRQF_TRIGGER_LOW,
                          ndev->name, ks);
        if (ret < 0) {
                dev_err(&spi->dev, "failed to get irq\n");
                goto err_irq;
        }

        ret = register_netdev(ndev);
        if (ret) {
                dev_err(&spi->dev, "failed to register network device\n");
                goto err_netdev;
        }

        netdev_info(ndev, "revision %d, MAC %pM, IRQ %d\n",
                    CIDER_REV_GET(ks8851_rdreg16(ks, KS_CIDER)),
                    ndev->dev_addr, ndev->irq);

        return 0;


err_netdev:
        free_irq(ndev->irq, ndev);

err_id:
err_irq:
        free_netdev(ndev);
        return ret;
}

static int __devexit ks8851_remove(struct spi_device *spi)
{
        struct ks8851_net *priv = dev_get_drvdata(&spi->dev);

        if (netif_msg_drv(priv))
                dev_info(&spi->dev, "remove\n");

        unregister_netdev(priv->netdev);
        free_irq(spi->irq, priv);
        free_netdev(priv->netdev);

        return 0;
}

static struct spi_driver ks8851_driver = {
        .driver = {
                .name = "ks8851",
                .owner = THIS_MODULE,
        },
        .probe = ks8851_probe,
        .remove = __devexit_p(ks8851_remove),
        .suspend = ks8851_suspend,
        .resume = ks8851_resume,
};

static int __init ks8851_init(void)
{
        return spi_register_driver(&ks8851_driver);
}

static void __exit ks8851_exit(void)
{
        spi_unregister_driver(&ks8851_driver);
}

module_init(ks8851_init);
module_exit(ks8851_exit);

MODULE_DESCRIPTION("KS8851 Network driver");
MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
MODULE_LICENSE("GPL");

module_param_named(message, msg_enable, int, 0);
MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)");
MODULE_ALIAS("spi:ks8851");