2 * This file function prototypes, data structure
3 * and definitions for all the host/station commands
12 #define DEFAULT_AD_HOC_CHANNEL 6
14 #define CMD_OPTION_WAITFORRSP 0x0002
16 /* Host command IDs */
19 * Return command are almost always the same as the host command, but with
20 * bit 15 set high. There are a few exceptions, though...
22 #define CMD_RET(cmd) (0x8000 | cmd)
24 /* Return command convention exceptions: */
25 #define CMD_RET_802_11_ASSOCIATE 0x8012
28 #define CMD_GET_HW_SPEC 0x0003
29 #define CMD_EEPROM_UPDATE 0x0004
30 #define CMD_802_11_RESET 0x0005
31 #define CMD_802_11_SCAN 0x0006
32 #define CMD_802_11_GET_LOG 0x000b
33 #define CMD_MAC_MULTICAST_ADR 0x0010
34 #define CMD_802_11_AUTHENTICATE 0x0011
35 #define CMD_802_11_EEPROM_ACCESS 0x0059
36 #define CMD_802_11_ASSOCIATE 0x0050
37 #define CMD_802_11_SET_WEP 0x0013
38 #define CMD_802_11_GET_STAT 0x0014
39 #define CMD_802_3_GET_STAT 0x0015
40 #define CMD_802_11_SNMP_MIB 0x0016
41 #define CMD_MAC_REG_MAP 0x0017
42 #define CMD_BBP_REG_MAP 0x0018
43 #define CMD_MAC_REG_ACCESS 0x0019
44 #define CMD_BBP_REG_ACCESS 0x001a
45 #define CMD_RF_REG_ACCESS 0x001b
46 #define CMD_802_11_RADIO_CONTROL 0x001c
47 #define CMD_802_11_RF_CHANNEL 0x001d
48 #define CMD_802_11_RF_TX_POWER 0x001e
49 #define CMD_802_11_RSSI 0x001f
50 #define CMD_802_11_RF_ANTENNA 0x0020
51 #define CMD_802_11_PS_MODE 0x0021
52 #define CMD_802_11_DATA_RATE 0x0022
53 #define CMD_RF_REG_MAP 0x0023
54 #define CMD_802_11_DEAUTHENTICATE 0x0024
55 #define CMD_802_11_REASSOCIATE 0x0025
56 #define CMD_MAC_CONTROL 0x0028
57 #define CMD_802_11_AD_HOC_START 0x002b
58 #define CMD_802_11_AD_HOC_JOIN 0x002c
59 #define CMD_802_11_QUERY_TKIP_REPLY_CNTRS 0x002e
60 #define CMD_802_11_ENABLE_RSN 0x002f
61 #define CMD_802_11_SET_AFC 0x003c
62 #define CMD_802_11_GET_AFC 0x003d
63 #define CMD_802_11_DEEP_SLEEP 0x003e
64 #define CMD_802_11_AD_HOC_STOP 0x0040
65 #define CMD_802_11_HOST_SLEEP_CFG 0x0043
66 #define CMD_802_11_WAKEUP_CONFIRM 0x0044
67 #define CMD_802_11_HOST_SLEEP_ACTIVATE 0x0045
68 #define CMD_802_11_BEACON_STOP 0x0049
69 #define CMD_802_11_MAC_ADDRESS 0x004d
70 #define CMD_802_11_LED_GPIO_CTRL 0x004e
71 #define CMD_802_11_EEPROM_ACCESS 0x0059
72 #define CMD_802_11_BAND_CONFIG 0x0058
73 #define CMD_GSPI_BUS_CONFIG 0x005a
74 #define CMD_802_11D_DOMAIN_INFO 0x005b
75 #define CMD_802_11_KEY_MATERIAL 0x005e
76 #define CMD_802_11_SLEEP_PARAMS 0x0066
77 #define CMD_802_11_INACTIVITY_TIMEOUT 0x0067
78 #define CMD_802_11_SLEEP_PERIOD 0x0068
79 #define CMD_802_11_TPC_CFG 0x0072
80 #define CMD_802_11_PA_CFG 0x0073
81 #define CMD_802_11_FW_WAKE_METHOD 0x0074
82 #define CMD_802_11_SUBSCRIBE_EVENT 0x0075
83 #define CMD_802_11_RATE_ADAPT_RATESET 0x0076
84 #define CMD_802_11_TX_RATE_QUERY 0x007f
85 #define CMD_GET_TSF 0x0080
86 #define CMD_BT_ACCESS 0x0087
87 #define CMD_FWT_ACCESS 0x0095
88 #define CMD_802_11_MONITOR_MODE 0x0098
89 #define CMD_MESH_ACCESS 0x009b
90 #define CMD_MESH_CONFIG_OLD 0x00a3
91 #define CMD_MESH_CONFIG 0x00ac
92 #define CMD_SET_BOOT2_VER 0x00a5
93 #define CMD_FUNC_INIT 0x00a9
94 #define CMD_FUNC_SHUTDOWN 0x00aa
95 #define CMD_802_11_BEACON_CTRL 0x00b0
97 /* For the IEEE Power Save */
98 #define PS_MODE_ACTION_ENTER_PS 0x0030
99 #define PS_MODE_ACTION_EXIT_PS 0x0031
100 #define PS_MODE_ACTION_SLEEP_CONFIRMED 0x0034
102 #define CMD_ENABLE_RSN 0x0001
103 #define CMD_DISABLE_RSN 0x0000
105 #define CMD_ACT_GET 0x0000
106 #define CMD_ACT_SET 0x0001
108 /* Define action or option for CMD_802_11_SET_WEP */
109 #define CMD_ACT_ADD 0x0002
110 #define CMD_ACT_REMOVE 0x0004
112 #define CMD_TYPE_WEP_40_BIT 0x01
113 #define CMD_TYPE_WEP_104_BIT 0x02
115 #define CMD_NUM_OF_WEP_KEYS 4
117 #define CMD_WEP_KEY_INDEX_MASK 0x3fff
119 /* Define action or option for CMD_802_11_SCAN */
120 #define CMD_BSS_TYPE_BSS 0x0001
121 #define CMD_BSS_TYPE_IBSS 0x0002
122 #define CMD_BSS_TYPE_ANY 0x0003
124 /* Define action or option for CMD_802_11_SCAN */
125 #define CMD_SCAN_TYPE_ACTIVE 0x0000
126 #define CMD_SCAN_TYPE_PASSIVE 0x0001
128 #define CMD_SCAN_RADIO_TYPE_BG 0
130 #define CMD_SCAN_PROBE_DELAY_TIME 0
132 /* Define action or option for CMD_MAC_CONTROL */
133 #define CMD_ACT_MAC_RX_ON 0x0001
134 #define CMD_ACT_MAC_TX_ON 0x0002
135 #define CMD_ACT_MAC_LOOPBACK_ON 0x0004
136 #define CMD_ACT_MAC_WEP_ENABLE 0x0008
137 #define CMD_ACT_MAC_INT_ENABLE 0x0010
138 #define CMD_ACT_MAC_MULTICAST_ENABLE 0x0020
139 #define CMD_ACT_MAC_BROADCAST_ENABLE 0x0040
140 #define CMD_ACT_MAC_PROMISCUOUS_ENABLE 0x0080
141 #define CMD_ACT_MAC_ALL_MULTICAST_ENABLE 0x0100
142 #define CMD_ACT_MAC_STRICT_PROTECTION_ENABLE 0x0400
144 /* Event flags for CMD_802_11_SUBSCRIBE_EVENT */
145 #define CMD_SUBSCRIBE_RSSI_LOW 0x0001
146 #define CMD_SUBSCRIBE_SNR_LOW 0x0002
147 #define CMD_SUBSCRIBE_FAILCOUNT 0x0004
148 #define CMD_SUBSCRIBE_BCNMISS 0x0008
149 #define CMD_SUBSCRIBE_RSSI_HIGH 0x0010
150 #define CMD_SUBSCRIBE_SNR_HIGH 0x0020
152 #define RADIO_PREAMBLE_LONG 0x00
153 #define RADIO_PREAMBLE_SHORT 0x02
154 #define RADIO_PREAMBLE_AUTO 0x04
156 /* Define action or option for CMD_802_11_RF_CHANNEL */
157 #define CMD_OPT_802_11_RF_CHANNEL_GET 0x00
158 #define CMD_OPT_802_11_RF_CHANNEL_SET 0x01
160 /* Define action or option for CMD_802_11_DATA_RATE */
161 #define CMD_ACT_SET_TX_AUTO 0x0000
162 #define CMD_ACT_SET_TX_FIX_RATE 0x0001
163 #define CMD_ACT_GET_TX_RATE 0x0002
165 /* Options for CMD_802_11_FW_WAKE_METHOD */
166 #define CMD_WAKE_METHOD_UNCHANGED 0x0000
167 #define CMD_WAKE_METHOD_COMMAND_INT 0x0001
168 #define CMD_WAKE_METHOD_GPIO 0x0002
170 /* Object IDs for CMD_802_11_SNMP_MIB */
171 #define SNMP_MIB_OID_BSS_TYPE 0x0000
172 #define SNMP_MIB_OID_OP_RATE_SET 0x0001
173 #define SNMP_MIB_OID_BEACON_PERIOD 0x0002 /* Reserved on v9+ */
174 #define SNMP_MIB_OID_DTIM_PERIOD 0x0003 /* Reserved on v9+ */
175 #define SNMP_MIB_OID_ASSOC_TIMEOUT 0x0004 /* Reserved on v9+ */
176 #define SNMP_MIB_OID_RTS_THRESHOLD 0x0005
177 #define SNMP_MIB_OID_SHORT_RETRY_LIMIT 0x0006
178 #define SNMP_MIB_OID_LONG_RETRY_LIMIT 0x0007
179 #define SNMP_MIB_OID_FRAG_THRESHOLD 0x0008
180 #define SNMP_MIB_OID_11D_ENABLE 0x0009
181 #define SNMP_MIB_OID_11H_ENABLE 0x000A
183 /* Define action or option for CMD_BT_ACCESS */
184 enum cmd_bt_access_opts
{
185 /* The bt commands start at 5 instead of 1 because the old dft commands
186 * are mapped to 1-4. These old commands are no longer maintained and
187 * should not be called.
189 CMD_ACT_BT_ACCESS_ADD
= 5,
190 CMD_ACT_BT_ACCESS_DEL
,
191 CMD_ACT_BT_ACCESS_LIST
,
192 CMD_ACT_BT_ACCESS_RESET
,
193 CMD_ACT_BT_ACCESS_SET_INVERT
,
194 CMD_ACT_BT_ACCESS_GET_INVERT
197 /* Define action or option for CMD_FWT_ACCESS */
198 enum cmd_fwt_access_opts
{
199 CMD_ACT_FWT_ACCESS_ADD
= 1,
200 CMD_ACT_FWT_ACCESS_DEL
,
201 CMD_ACT_FWT_ACCESS_LOOKUP
,
202 CMD_ACT_FWT_ACCESS_LIST
,
203 CMD_ACT_FWT_ACCESS_LIST_ROUTE
,
204 CMD_ACT_FWT_ACCESS_LIST_NEIGHBOR
,
205 CMD_ACT_FWT_ACCESS_RESET
,
206 CMD_ACT_FWT_ACCESS_CLEANUP
,
207 CMD_ACT_FWT_ACCESS_TIME
,
210 /* Define action or option for CMD_802_11_HOST_SLEEP_CFG */
211 enum cmd_wol_cfg_opts
{
212 CMD_ACT_ACTION_NONE
= 0,
213 CMD_ACT_SET_WOL_RULE
,
214 CMD_ACT_GET_WOL_RULE
,
215 CMD_ACT_RESET_WOL_RULE
,
218 /* Define action or option for CMD_MESH_ACCESS */
219 enum cmd_mesh_access_opts
{
220 CMD_ACT_MESH_GET_TTL
= 1,
221 CMD_ACT_MESH_SET_TTL
,
222 CMD_ACT_MESH_GET_STATS
,
223 CMD_ACT_MESH_GET_ANYCAST
,
224 CMD_ACT_MESH_SET_ANYCAST
,
225 CMD_ACT_MESH_SET_LINK_COSTS
,
226 CMD_ACT_MESH_GET_LINK_COSTS
,
227 CMD_ACT_MESH_SET_BCAST_RATE
,
228 CMD_ACT_MESH_GET_BCAST_RATE
,
229 CMD_ACT_MESH_SET_RREQ_DELAY
,
230 CMD_ACT_MESH_GET_RREQ_DELAY
,
231 CMD_ACT_MESH_SET_ROUTE_EXP
,
232 CMD_ACT_MESH_GET_ROUTE_EXP
,
233 CMD_ACT_MESH_SET_AUTOSTART_ENABLED
,
234 CMD_ACT_MESH_GET_AUTOSTART_ENABLED
,
235 CMD_ACT_MESH_SET_GET_PRB_RSP_LIMIT
= 17,
238 /* Define actions and types for CMD_MESH_CONFIG */
239 enum cmd_mesh_config_actions
{
240 CMD_ACT_MESH_CONFIG_STOP
= 0,
241 CMD_ACT_MESH_CONFIG_START
,
242 CMD_ACT_MESH_CONFIG_SET
,
243 CMD_ACT_MESH_CONFIG_GET
,
246 enum cmd_mesh_config_types
{
247 CMD_TYPE_MESH_SET_BOOTFLAG
= 1,
248 CMD_TYPE_MESH_SET_BOOTTIME
,
249 CMD_TYPE_MESH_SET_DEF_CHANNEL
,
250 CMD_TYPE_MESH_SET_MESH_IE
,
251 CMD_TYPE_MESH_GET_DEFAULTS
,
252 CMD_TYPE_MESH_GET_MESH_IE
, /* GET_DEFAULTS is superset of GET_MESHIE */
255 /* Card Event definition */
256 #define MACREG_INT_CODE_TX_PPA_FREE 0
257 #define MACREG_INT_CODE_TX_DMA_DONE 1
258 #define MACREG_INT_CODE_LINK_LOST_W_SCAN 2
259 #define MACREG_INT_CODE_LINK_LOST_NO_SCAN 3
260 #define MACREG_INT_CODE_LINK_SENSED 4
261 #define MACREG_INT_CODE_CMD_FINISHED 5
262 #define MACREG_INT_CODE_MIB_CHANGED 6
263 #define MACREG_INT_CODE_INIT_DONE 7
264 #define MACREG_INT_CODE_DEAUTHENTICATED 8
265 #define MACREG_INT_CODE_DISASSOCIATED 9
266 #define MACREG_INT_CODE_PS_AWAKE 10
267 #define MACREG_INT_CODE_PS_SLEEP 11
268 #define MACREG_INT_CODE_MIC_ERR_MULTICAST 13
269 #define MACREG_INT_CODE_MIC_ERR_UNICAST 14
270 #define MACREG_INT_CODE_WM_AWAKE 15
271 #define MACREG_INT_CODE_DEEP_SLEEP_AWAKE 16
272 #define MACREG_INT_CODE_ADHOC_BCN_LOST 17
273 #define MACREG_INT_CODE_HOST_AWAKE 18
274 #define MACREG_INT_CODE_STOP_TX 19
275 #define MACREG_INT_CODE_START_TX 20
276 #define MACREG_INT_CODE_CHANNEL_SWITCH 21
277 #define MACREG_INT_CODE_MEASUREMENT_RDY 22
278 #define MACREG_INT_CODE_WMM_CHANGE 23
279 #define MACREG_INT_CODE_BG_SCAN_REPORT 24
280 #define MACREG_INT_CODE_RSSI_LOW 25
281 #define MACREG_INT_CODE_SNR_LOW 26
282 #define MACREG_INT_CODE_MAX_FAIL 27
283 #define MACREG_INT_CODE_RSSI_HIGH 28
284 #define MACREG_INT_CODE_SNR_HIGH 29
285 #define MACREG_INT_CODE_MESH_AUTO_STARTED 35
286 #define MACREG_INT_CODE_FIRMWARE_READY 48
289 /* 802.11-related definitions */
291 /* TxPD descriptor */
293 /* union to cope up with later FW revisions */
295 /* Current Tx packet status */
298 /* BSS type: client, AP, etc. */
308 __le32 tx_packet_location
;
309 /* Tx packet length */
310 __le16 tx_packet_length
;
311 /* First 2 byte of destination MAC address */
312 u8 tx_dest_addr_high
[2];
313 /* Last 4 byte of destination MAC address */
314 u8 tx_dest_addr_low
[4];
317 /* Pkt Trasnit Power control */
319 /* Amount of time the packet has been queued (units = 2ms) */
325 /* RxPD Descriptor */
327 /* union to cope up with later FW revisions */
329 /* Current Rx packet status */
332 /* BSS type: client, AP, etc. */
357 /* Next Rx RxPD addr */
358 __le32 next_rxpd_ptr
;
372 /* Generic structure to hold all key types. */
375 u16 flags
; /* KEY_INFO_* from defs.h */
376 u16 type
; /* KEY_TYPE_* from defs.h */
380 /* lbs_offset_value */
381 struct lbs_offset_value
{
386 #define MAX_11D_TRIPLETS 83
388 struct mrvl_ie_domain_param_set
{
389 struct mrvl_ie_header header
;
391 u8 country_code
[IEEE80211_COUNTRY_STRING_LEN
];
392 struct ieee80211_country_ie_triplet triplet
[MAX_11D_TRIPLETS
];
395 struct cmd_ds_802_11d_domain_info
{
396 struct cmd_header hdr
;
399 struct mrvl_ie_domain_param_set domain
;
403 * Define data structure for CMD_GET_HW_SPEC
404 * This structure defines the response for the GET_HW_SPEC command
406 struct cmd_ds_get_hw_spec
{
407 struct cmd_header hdr
;
409 /* HW Interface version number */
411 /* HW version number */
413 /* Max number of TxPD FW can handle */
415 /* Max no of Multicast address */
423 /* Number of antenna used */
426 /* FW release number, example 0x01030304 = 2.3.4p1 */
429 /* Base Address of TxPD queue */
431 /* Read Pointer of RxPd queue */
434 /* Write Pointer of RxPd queue */
437 /*FW/HW capability */
441 struct cmd_ds_802_11_subscribe_event
{
442 struct cmd_header hdr
;
447 /* A TLV to the CMD_802_11_SUBSCRIBE_EVENT command can contain a
448 * number of TLVs. From the v5.1 manual, those TLVs would add up to
449 * 40 bytes. However, future firmware might add additional TLVs, so I
450 * bump this up a bit.
456 * This scan handle Country Information IE(802.11d compliant)
457 * Define data structure for CMD_802_11_SCAN
459 struct cmd_ds_802_11_scan
{
460 struct cmd_header hdr
;
463 uint8_t bssid
[ETH_ALEN
];
464 uint8_t tlvbuffer
[0];
467 struct cmd_ds_802_11_scan_rsp
{
468 struct cmd_header hdr
;
470 __le16 bssdescriptsize
;
472 uint8_t bssdesc_and_tlvbuffer
[0];
475 struct cmd_ds_802_11_get_log
{
476 struct cmd_header hdr
;
490 __le32 wepundecryptable
;
493 struct cmd_ds_mac_control
{
494 struct cmd_header hdr
;
499 struct cmd_ds_mac_multicast_adr
{
500 struct cmd_header hdr
;
503 u8 maclist
[ETH_ALEN
* MRVDRV_MAX_MULTICAST_LIST_SIZE
];
506 struct cmd_ds_802_11_authenticate
{
507 struct cmd_header hdr
;
514 struct cmd_ds_802_11_deauthenticate
{
515 struct cmd_header hdr
;
517 u8 macaddr
[ETH_ALEN
];
521 struct cmd_ds_802_11_associate
{
522 struct cmd_header hdr
;
526 __le16 listeninterval
;
529 u8 iebuf
[512]; /* Enough for required and most optional IEs */
532 struct cmd_ds_802_11_associate_response
{
533 struct cmd_header hdr
;
541 struct cmd_ds_802_11_set_wep
{
542 struct cmd_header hdr
;
544 /* ACT_ADD, ACT_REMOVE or ACT_ENABLE */
547 /* key Index selected for Tx */
550 /* 40, 128bit or TXWEP */
552 uint8_t keymaterial
[4][16];
555 struct cmd_ds_802_11_snmp_mib
{
556 struct cmd_header hdr
;
564 struct cmd_ds_reg_access
{
565 struct cmd_header hdr
;
570 u8 bbp_rf
; /* for BBP and RF registers */
571 __le32 mac
; /* for MAC registers */
575 struct cmd_ds_802_11_radio_control
{
576 struct cmd_header hdr
;
582 struct cmd_ds_802_11_beacon_control
{
583 struct cmd_header hdr
;
586 __le16 beacon_enable
;
587 __le16 beacon_period
;
590 struct cmd_ds_802_11_sleep_params
{
591 struct cmd_header hdr
;
593 /* ACT_GET/ACT_SET */
596 /* Sleep clock error in ppm */
599 /* Wakeup offset in usec */
602 /* Clock stabilization time in usec */
605 /* control periodic calibration */
608 /* control the use of external sleep clock */
609 uint8_t externalsleepclk
;
611 /* reserved field, should be set to zero */
615 struct cmd_ds_802_11_rf_channel
{
616 struct cmd_header hdr
;
620 __le16 rftype
; /* unused */
621 __le16 reserved
; /* unused */
622 u8 channellist
[32]; /* unused */
625 struct cmd_ds_802_11_rssi
{
626 struct cmd_header hdr
;
629 * request: number of beacons (N) to average the SNR and NF over
630 * response: SNR of most recent beacon
635 * The following fields are only set in the response.
636 * In the request these are reserved and should be set to 0.
638 __le16 nf
; /* most recent beacon noise floor */
639 __le16 avg_snr
; /* average SNR weighted by N from request */
640 __le16 avg_nf
; /* average noise floor weighted by N from request */
643 struct cmd_ds_802_11_mac_address
{
644 struct cmd_header hdr
;
650 struct cmd_ds_802_11_rf_tx_power
{
651 struct cmd_header hdr
;
659 /* MONITOR_MODE only exists in OLPC v5 firmware */
660 struct cmd_ds_802_11_monitor_mode
{
661 struct cmd_header hdr
;
667 struct cmd_ds_set_boot2_ver
{
668 struct cmd_header hdr
;
674 struct cmd_ds_802_11_fw_wake_method
{
675 struct cmd_header hdr
;
681 struct cmd_ds_802_11_ps_mode
{
682 struct cmd_header hdr
;
687 * Interval for keepalive in PS mode:
688 * 0x0000 = don't change
689 * 0x001E = firmware default
692 __le16 nullpktinterval
;
695 * Number of DTIM intervals to wake up for:
697 * 1 = firmware default
703 __le16 locallisteninterval
;
706 * AdHoc awake period (FW v9+ only):
708 * 1 = always awake (IEEE standard behavior)
709 * 2 - 31 = sleep for (n - 1) periods and awake for 1 period
711 * 255 = sleep at each ATIM
713 __le16 adhoc_awake_period
;
716 struct cmd_confirm_sleep
{
717 struct cmd_header hdr
;
720 __le16 nullpktinterval
;
723 __le16 locallisteninterval
;
726 struct cmd_ds_802_11_data_rate
{
727 struct cmd_header hdr
;
734 struct cmd_ds_802_11_rate_adapt_rateset
{
735 struct cmd_header hdr
;
741 struct cmd_ds_802_11_ad_hoc_start
{
742 struct cmd_header hdr
;
744 u8 ssid
[IEEE80211_MAX_SSID_LEN
];
747 u8 dtimperiod
; /* Reserved on v9 and later */
748 struct ieee_ie_ibss_param_set ibss
;
750 struct ieee_ie_ds_param_set ds
;
752 __le16 probedelay
; /* Reserved on v9 and later */
755 u8 tlv_memory_size_pad
[100];
758 struct cmd_ds_802_11_ad_hoc_result
{
759 struct cmd_header hdr
;
765 struct adhoc_bssdesc
{
767 u8 ssid
[IEEE80211_MAX_SSID_LEN
];
773 struct ieee_ie_ds_param_set ds
;
775 struct ieee_ie_ibss_param_set ibss
;
781 * DO NOT ADD ANY FIELDS TO THIS STRUCTURE. It is used below in the
782 * Adhoc join command and will cause a binary layout mismatch with
787 struct cmd_ds_802_11_ad_hoc_join
{
788 struct cmd_header hdr
;
790 struct adhoc_bssdesc bss
;
791 __le16 failtimeout
; /* Reserved on v9 and later */
792 __le16 probedelay
; /* Reserved on v9 and later */
795 struct cmd_ds_802_11_ad_hoc_stop
{
796 struct cmd_header hdr
;
799 struct cmd_ds_802_11_enable_rsn
{
800 struct cmd_header hdr
;
806 struct MrvlIEtype_keyParamSet
{
810 /* length of Payload */
813 /* type of key: WEP=0, TKIP=1, AES=2 */
816 /* key control Info specific to a keytypeid */
822 /* key material of size keylen */
826 #define MAX_WOL_RULES 16
828 struct host_wol_rule
{
841 uint8_t no_rules_in_cmd
;
843 struct host_wol_rule rule
[MAX_WOL_RULES
];
846 struct cmd_ds_host_sleep
{
847 struct cmd_header hdr
;
851 struct wol_config wol_conf
;
856 struct cmd_ds_802_11_key_material
{
857 struct cmd_header hdr
;
860 struct MrvlIEtype_keyParamSet keyParamSet
[2];
863 struct cmd_ds_802_11_eeprom_access
{
864 struct cmd_header hdr
;
868 /* firmware says it returns a maximum of 20 bytes */
869 #define LBS_EEPROM_READ_LEN 20
870 u8 value
[LBS_EEPROM_READ_LEN
];
873 struct cmd_ds_802_11_tpc_cfg
{
874 struct cmd_header hdr
;
885 struct cmd_ds_802_11_pa_cfg
{
886 struct cmd_header hdr
;
896 struct cmd_ds_802_11_led_ctrl
{
897 struct cmd_header hdr
;
904 /* Automatic Frequency Control */
905 struct cmd_ds_802_11_afc
{
906 struct cmd_header hdr
;
915 __le16 timing_offset
; /* signed */
916 __le16 carrier_offset
; /* signed */
921 struct cmd_tx_rate_query
{
925 struct cmd_ds_get_tsf
{
929 struct cmd_ds_bt_access
{
930 struct cmd_header hdr
;
938 struct cmd_ds_fwt_access
{
939 struct cmd_header hdr
;
960 struct cmd_ds_mesh_config
{
961 struct cmd_header hdr
;
967 u8 data
[128]; /* last position reserved */
970 struct cmd_ds_mesh_access
{
971 struct cmd_header hdr
;
974 __le32 data
[32]; /* last position reserved */
977 /* Number of stats counters returned by the firmware */
978 #define MESH_STATS_NUM 8