2 * QLogic Fibre Channel HBA Driver
3 * Copyright (c) 2003-2011 QLogic Corporation
5 * See LICENSE.qla2xxx for copyright and licensing details.
10 #include <linux/kernel.h>
11 #include <linux/init.h>
12 #include <linux/types.h>
13 #include <linux/module.h>
14 #include <linux/list.h>
15 #include <linux/pci.h>
16 #include <linux/dma-mapping.h>
17 #include <linux/sched.h>
18 #include <linux/slab.h>
19 #include <linux/dmapool.h>
20 #include <linux/mempool.h>
21 #include <linux/spinlock.h>
22 #include <linux/completion.h>
23 #include <linux/interrupt.h>
24 #include <linux/workqueue.h>
25 #include <linux/firmware.h>
26 #include <linux/aer.h>
27 #include <linux/mutex.h>
29 #include <scsi/scsi.h>
30 #include <scsi/scsi_host.h>
31 #include <scsi/scsi_device.h>
32 #include <scsi/scsi_cmnd.h>
33 #include <scsi/scsi_transport_fc.h>
34 #include <scsi/scsi_bsg_fc.h>
38 #define QLA2XXX_DRIVER_NAME "qla2xxx"
39 #define QLA2XXX_APIDEV "ql2xapidev"
42 * We have MAILBOX_REGISTER_COUNT sized arrays in a few places,
43 * but that's fine as we don't look at the last 24 ones for
46 #define MAILBOX_REGISTER_COUNT_2100 8
47 #define MAILBOX_REGISTER_COUNT 32
49 #define QLA2200A_RISC_ROM_VER 4
53 #include "qla_settings.h"
56 * Data bit definitions
74 #define BIT_16 0x10000
75 #define BIT_17 0x20000
76 #define BIT_18 0x40000
77 #define BIT_19 0x80000
78 #define BIT_20 0x100000
79 #define BIT_21 0x200000
80 #define BIT_22 0x400000
81 #define BIT_23 0x800000
82 #define BIT_24 0x1000000
83 #define BIT_25 0x2000000
84 #define BIT_26 0x4000000
85 #define BIT_27 0x8000000
86 #define BIT_28 0x10000000
87 #define BIT_29 0x20000000
88 #define BIT_30 0x40000000
89 #define BIT_31 0x80000000
91 #define LSB(x) ((uint8_t)(x))
92 #define MSB(x) ((uint8_t)((uint16_t)(x) >> 8))
94 #define LSW(x) ((uint16_t)(x))
95 #define MSW(x) ((uint16_t)((uint32_t)(x) >> 16))
97 #define LSD(x) ((uint32_t)((uint64_t)(x)))
98 #define MSD(x) ((uint32_t)((((uint64_t)(x)) >> 16) >> 16))
100 #define MAKE_HANDLE(x, y) ((uint32_t)((((uint32_t)(x)) << 16) | (uint32_t)(y)))
106 #define RD_REG_BYTE(addr) readb(addr)
107 #define RD_REG_WORD(addr) readw(addr)
108 #define RD_REG_DWORD(addr) readl(addr)
109 #define RD_REG_BYTE_RELAXED(addr) readb_relaxed(addr)
110 #define RD_REG_WORD_RELAXED(addr) readw_relaxed(addr)
111 #define RD_REG_DWORD_RELAXED(addr) readl_relaxed(addr)
112 #define WRT_REG_BYTE(addr, data) writeb(data,addr)
113 #define WRT_REG_WORD(addr, data) writew(data,addr)
114 #define WRT_REG_DWORD(addr, data) writel(data,addr)
117 * The ISP2312 v2 chip cannot access the FLASH/GPIO registers via MMIO in an
120 #define RD_REG_WORD_PIO(addr) (inw((unsigned long)addr))
121 #define WRT_REG_WORD_PIO(addr, data) (outw(data,(unsigned long)addr))
124 * Fibre Channel device definitions.
126 #define WWN_SIZE 8 /* Size of WWPN, WWN & WWNN */
127 #define MAX_FIBRE_DEVICES 512
128 #define MAX_FIBRE_LUNS 0xFFFF
129 #define MAX_RSCN_COUNT 32
130 #define MAX_HOST_COUNT 16
133 * Host adapter default definitions.
135 #define MAX_BUSES 1 /* We only have one bus today */
136 #define MAX_TARGETS_2100 MAX_FIBRE_DEVICES
137 #define MAX_TARGETS_2200 MAX_FIBRE_DEVICES
139 #define MAX_LUNS MAX_FIBRE_LUNS
140 #define MAX_CMDS_PER_LUN 255
143 * Fibre Channel device definitions.
145 #define SNS_LAST_LOOP_ID_2100 0xfe
146 #define SNS_LAST_LOOP_ID_2300 0x7ff
148 #define LAST_LOCAL_LOOP_ID 0x7d
149 #define SNS_FL_PORT 0x7e
150 #define FABRIC_CONTROLLER 0x7f
151 #define SIMPLE_NAME_SERVER 0x80
152 #define SNS_FIRST_LOOP_ID 0x81
153 #define MANAGEMENT_SERVER 0xfe
154 #define BROADCAST 0xff
157 * There is no correspondence between an N-PORT id and an AL_PA. Therefore the
158 * valid range of an N-PORT id is 0 through 0x7ef.
160 #define NPH_LAST_HANDLE 0x7ef
161 #define NPH_MGMT_SERVER 0x7fa /* FFFFFA */
162 #define NPH_SNS 0x7fc /* FFFFFC */
163 #define NPH_FABRIC_CONTROLLER 0x7fd /* FFFFFD */
164 #define NPH_F_PORT 0x7fe /* FFFFFE */
165 #define NPH_IP_BROADCAST 0x7ff /* FFFFFF */
167 #define MAX_CMDSZ 16 /* SCSI maximum CDB size. */
171 * Timeout timer counts in seconds
173 #define PORT_RETRY_TIME 1
174 #define LOOP_DOWN_TIMEOUT 60
175 #define LOOP_DOWN_TIME 255 /* 240 */
176 #define LOOP_DOWN_RESET (LOOP_DOWN_TIME - 30)
178 /* Maximum outstanding commands in ISP queues (1-65535) */
179 #define MAX_OUTSTANDING_COMMANDS 1024
181 /* ISP request and response entry counts (37-65535) */
182 #define REQUEST_ENTRY_CNT_2100 128 /* Number of request entries. */
183 #define REQUEST_ENTRY_CNT_2200 2048 /* Number of request entries. */
184 #define REQUEST_ENTRY_CNT_24XX 2048 /* Number of request entries. */
185 #define RESPONSE_ENTRY_CNT_2100 64 /* Number of response entries.*/
186 #define RESPONSE_ENTRY_CNT_2300 512 /* Number of response entries.*/
187 #define RESPONSE_ENTRY_CNT_MQ 128 /* Number of response entries.*/
192 * (sd.h is not exported, hence local inclusion)
193 * Data Integrity Field tuple.
195 struct sd_dif_tuple
{
196 __be16 guard_tag
; /* Checksum */
197 __be16 app_tag
; /* Opaque storage */
198 __be32 ref_tag
; /* Target LBA or indirect LBA */
206 struct fc_port
*fcport
;
209 struct scsi_cmnd
*cmd
; /* Linux SCSI command pkt */
213 uint32_t request_sense_length
;
214 uint8_t *request_sense_ptr
;
220 * SRB flag definitions
222 #define SRB_DMA_VALID BIT_0 /* Command sent to ISP */
223 #define SRB_FCP_CMND_DMA_VALID BIT_12 /* DIF: DSD List valid */
224 #define SRB_CRC_CTX_DMA_VALID BIT_2 /* DIF: context DMA valid */
225 #define SRB_CRC_PROT_DMA_VALID BIT_4 /* DIF: prot DMA valid */
226 #define SRB_CRC_CTX_DSD_VALID BIT_5 /* DIF: dsd_list valid */
228 /* To identify if a srb is of T10-CRC type. @sp => srb_t pointer */
229 #define IS_PROT_IO(sp) (sp->flags & SRB_CRC_CTX_DSD_VALID)
238 #define SRB_LOGIN_RETRIED BIT_0
239 #define SRB_LOGIN_COND_PLOGI BIT_1
240 #define SRB_LOGIN_SKIP_PRLI BIT_2
245 * Values for flags field below are as
246 * defined in tsk_mgmt_entry struct
247 * for control_flags field in qla_fw.h.
255 struct timer_list timer
;
257 void (*done
)(srb_t
*);
258 void (*free
)(srb_t
*);
259 void (*timeout
)(srb_t
*);
262 /* Values for srb_ctx type */
263 #define SRB_LOGIN_CMD 1
264 #define SRB_LOGOUT_CMD 2
265 #define SRB_ELS_CMD_RPT 3
266 #define SRB_ELS_CMD_HST 4
268 #define SRB_ADISC_CMD 6
275 struct srb_iocb
*iocb_cmd
;
276 struct fc_bsg_job
*bsg_job
;
286 uint32_t transfer_size
;
290 * ISP I/O Register Set structure definitions.
292 struct device_reg_2xxx
{
293 uint16_t flash_address
; /* Flash BIOS address */
294 uint16_t flash_data
; /* Flash BIOS data */
295 uint16_t unused_1
[1]; /* Gap */
296 uint16_t ctrl_status
; /* Control/Status */
297 #define CSR_FLASH_64K_BANK BIT_3 /* Flash upper 64K bank select */
298 #define CSR_FLASH_ENABLE BIT_1 /* Flash BIOS Read/Write enable */
299 #define CSR_ISP_SOFT_RESET BIT_0 /* ISP soft reset */
301 uint16_t ictrl
; /* Interrupt control */
302 #define ICR_EN_INT BIT_15 /* ISP enable interrupts. */
303 #define ICR_EN_RISC BIT_3 /* ISP enable RISC interrupts. */
305 uint16_t istatus
; /* Interrupt status */
306 #define ISR_RISC_INT BIT_3 /* RISC interrupt */
308 uint16_t semaphore
; /* Semaphore */
309 uint16_t nvram
; /* NVRAM register. */
310 #define NVR_DESELECT 0
311 #define NVR_BUSY BIT_15
312 #define NVR_WRT_ENABLE BIT_14 /* Write enable */
313 #define NVR_PR_ENABLE BIT_13 /* Protection register enable */
314 #define NVR_DATA_IN BIT_3
315 #define NVR_DATA_OUT BIT_2
316 #define NVR_SELECT BIT_1
317 #define NVR_CLOCK BIT_0
319 #define NVR_WAIT_CNT 20000
331 uint16_t unused_2
[59]; /* Gap */
332 } __attribute__((packed
)) isp2100
;
335 uint16_t req_q_in
; /* In-Pointer */
336 uint16_t req_q_out
; /* Out-Pointer */
338 uint16_t rsp_q_in
; /* In-Pointer */
339 uint16_t rsp_q_out
; /* Out-Pointer */
341 /* RISC to Host Status */
342 uint32_t host_status
;
343 #define HSR_RISC_INT BIT_15 /* RISC interrupt */
344 #define HSR_RISC_PAUSED BIT_8 /* RISC Paused */
346 /* Host to Host Semaphore */
347 uint16_t host_semaphore
;
348 uint16_t unused_3
[17]; /* Gap */
382 uint16_t unused_4
[10]; /* Gap */
383 } __attribute__((packed
)) isp2300
;
386 uint16_t fpm_diag_config
;
387 uint16_t unused_5
[0x4]; /* Gap */
389 uint16_t unused_5_1
; /* Gap */
390 uint16_t pcr
; /* Processor Control Register. */
391 uint16_t unused_6
[0x5]; /* Gap */
392 uint16_t mctr
; /* Memory Configuration and Timing. */
393 uint16_t unused_7
[0x3]; /* Gap */
394 uint16_t fb_cmd_2100
; /* Unused on 23XX */
395 uint16_t unused_8
[0x3]; /* Gap */
396 uint16_t hccr
; /* Host command & control register. */
397 #define HCCR_HOST_INT BIT_7 /* Host interrupt bit */
398 #define HCCR_RISC_PAUSE BIT_5 /* Pause mode bit */
400 #define HCCR_RESET_RISC 0x1000 /* Reset RISC */
401 #define HCCR_PAUSE_RISC 0x2000 /* Pause RISC */
402 #define HCCR_RELEASE_RISC 0x3000 /* Release RISC from reset. */
403 #define HCCR_SET_HOST_INT 0x5000 /* Set host interrupt */
404 #define HCCR_CLR_HOST_INT 0x6000 /* Clear HOST interrupt */
405 #define HCCR_CLR_RISC_INT 0x7000 /* Clear RISC interrupt */
406 #define HCCR_DISABLE_PARITY_PAUSE 0x4001 /* Disable parity error RISC pause. */
407 #define HCCR_ENABLE_PARITY 0xA000 /* Enable PARITY interrupt */
409 uint16_t unused_9
[5]; /* Gap */
410 uint16_t gpiod
; /* GPIO Data register. */
411 uint16_t gpioe
; /* GPIO Enable register. */
412 #define GPIO_LED_MASK 0x00C0
413 #define GPIO_LED_GREEN_OFF_AMBER_OFF 0x0000
414 #define GPIO_LED_GREEN_ON_AMBER_OFF 0x0040
415 #define GPIO_LED_GREEN_OFF_AMBER_ON 0x0080
416 #define GPIO_LED_GREEN_ON_AMBER_ON 0x00C0
417 #define GPIO_LED_ALL_OFF 0x0000
418 #define GPIO_LED_RED_ON_OTHER_OFF 0x0001 /* isp2322 */
419 #define GPIO_LED_RGA_ON 0x00C1 /* isp2322: red green amber */
423 uint16_t unused_10
[8]; /* Gap */
439 uint16_t mailbox23
; /* Also probe reg. */
440 } __attribute__((packed
)) isp2200
;
444 struct device_reg_25xxmq
{
452 struct device_reg_2xxx isp
;
453 struct device_reg_24xx isp24
;
454 struct device_reg_25xxmq isp25mq
;
455 struct device_reg_82xx isp82
;
458 #define ISP_REQ_Q_IN(ha, reg) \
459 (IS_QLA2100(ha) || IS_QLA2200(ha) ? \
460 &(reg)->u.isp2100.mailbox4 : \
461 &(reg)->u.isp2300.req_q_in)
462 #define ISP_REQ_Q_OUT(ha, reg) \
463 (IS_QLA2100(ha) || IS_QLA2200(ha) ? \
464 &(reg)->u.isp2100.mailbox4 : \
465 &(reg)->u.isp2300.req_q_out)
466 #define ISP_RSP_Q_IN(ha, reg) \
467 (IS_QLA2100(ha) || IS_QLA2200(ha) ? \
468 &(reg)->u.isp2100.mailbox5 : \
469 &(reg)->u.isp2300.rsp_q_in)
470 #define ISP_RSP_Q_OUT(ha, reg) \
471 (IS_QLA2100(ha) || IS_QLA2200(ha) ? \
472 &(reg)->u.isp2100.mailbox5 : \
473 &(reg)->u.isp2300.rsp_q_out)
475 #define MAILBOX_REG(ha, reg, num) \
476 (IS_QLA2100(ha) || IS_QLA2200(ha) ? \
478 &(reg)->u.isp2100.mailbox0 + (num) : \
479 &(reg)->u_end.isp2200.mailbox8 + (num) - 8) : \
480 &(reg)->u.isp2300.mailbox0 + (num))
481 #define RD_MAILBOX_REG(ha, reg, num) \
482 RD_REG_WORD(MAILBOX_REG(ha, reg, num))
483 #define WRT_MAILBOX_REG(ha, reg, num, data) \
484 WRT_REG_WORD(MAILBOX_REG(ha, reg, num), data)
486 #define FB_CMD_REG(ha, reg) \
487 (IS_QLA2100(ha) || IS_QLA2200(ha) ? \
488 &(reg)->fb_cmd_2100 : \
489 &(reg)->u.isp2300.fb_cmd)
490 #define RD_FB_CMD_REG(ha, reg) \
491 RD_REG_WORD(FB_CMD_REG(ha, reg))
492 #define WRT_FB_CMD_REG(ha, reg, data) \
493 WRT_REG_WORD(FB_CMD_REG(ha, reg), data)
496 uint32_t out_mb
; /* outbound from driver */
497 uint32_t in_mb
; /* Incoming from RISC */
498 uint16_t mb
[MAILBOX_REGISTER_COUNT
];
503 #define MBX_DMA_IN BIT_0
504 #define MBX_DMA_OUT BIT_1
505 #define IOCTL_CMD BIT_2
508 #define MBX_TOV_SECONDS 30
511 * ISP product identification definitions in mailboxes after reset.
513 #define PROD_ID_1 0x4953
514 #define PROD_ID_2 0x0000
515 #define PROD_ID_2a 0x5020
516 #define PROD_ID_3 0x2020
519 * ISP mailbox Self-Test status codes
521 #define MBS_FRM_ALIVE 0 /* Firmware Alive. */
522 #define MBS_CHKSUM_ERR 1 /* Checksum Error. */
523 #define MBS_BUSY 4 /* Busy. */
526 * ISP mailbox command complete status codes
528 #define MBS_COMMAND_COMPLETE 0x4000
529 #define MBS_INVALID_COMMAND 0x4001
530 #define MBS_HOST_INTERFACE_ERROR 0x4002
531 #define MBS_TEST_FAILED 0x4003
532 #define MBS_COMMAND_ERROR 0x4005
533 #define MBS_COMMAND_PARAMETER_ERROR 0x4006
534 #define MBS_PORT_ID_USED 0x4007
535 #define MBS_LOOP_ID_USED 0x4008
536 #define MBS_ALL_IDS_IN_USE 0x4009
537 #define MBS_NOT_LOGGED_IN 0x400A
538 #define MBS_LINK_DOWN_ERROR 0x400B
539 #define MBS_DIAG_ECHO_TEST_ERROR 0x400C
542 * ISP mailbox asynchronous event status codes
544 #define MBA_ASYNC_EVENT 0x8000 /* Asynchronous event. */
545 #define MBA_RESET 0x8001 /* Reset Detected. */
546 #define MBA_SYSTEM_ERR 0x8002 /* System Error. */
547 #define MBA_REQ_TRANSFER_ERR 0x8003 /* Request Transfer Error. */
548 #define MBA_RSP_TRANSFER_ERR 0x8004 /* Response Transfer Error. */
549 #define MBA_WAKEUP_THRES 0x8005 /* Request Queue Wake-up. */
550 #define MBA_LIP_OCCURRED 0x8010 /* Loop Initialization Procedure */
552 #define MBA_LOOP_UP 0x8011 /* FC Loop UP. */
553 #define MBA_LOOP_DOWN 0x8012 /* FC Loop Down. */
554 #define MBA_LIP_RESET 0x8013 /* LIP reset occurred. */
555 #define MBA_PORT_UPDATE 0x8014 /* Port Database update. */
556 #define MBA_RSCN_UPDATE 0x8015 /* Register State Chg Notification. */
557 #define MBA_LIP_F8 0x8016 /* Received a LIP F8. */
558 #define MBA_LOOP_INIT_ERR 0x8017 /* Loop Initialization Error. */
559 #define MBA_FABRIC_AUTH_REQ 0x801b /* Fabric Authentication Required. */
560 #define MBA_SCSI_COMPLETION 0x8020 /* SCSI Command Complete. */
561 #define MBA_CTIO_COMPLETION 0x8021 /* CTIO Complete. */
562 #define MBA_IP_COMPLETION 0x8022 /* IP Transmit Command Complete. */
563 #define MBA_IP_RECEIVE 0x8023 /* IP Received. */
564 #define MBA_IP_BROADCAST 0x8024 /* IP Broadcast Received. */
565 #define MBA_IP_LOW_WATER_MARK 0x8025 /* IP Low Water Mark reached. */
566 #define MBA_IP_RCV_BUFFER_EMPTY 0x8026 /* IP receive buffer queue empty. */
567 #define MBA_IP_HDR_DATA_SPLIT 0x8027 /* IP header/data splitting feature */
569 #define MBA_TRACE_NOTIFICATION 0x8028 /* Trace/Diagnostic notification. */
570 #define MBA_POINT_TO_POINT 0x8030 /* Point to point mode. */
571 #define MBA_CMPLT_1_16BIT 0x8031 /* Completion 1 16bit IOSB. */
572 #define MBA_CMPLT_2_16BIT 0x8032 /* Completion 2 16bit IOSB. */
573 #define MBA_CMPLT_3_16BIT 0x8033 /* Completion 3 16bit IOSB. */
574 #define MBA_CMPLT_4_16BIT 0x8034 /* Completion 4 16bit IOSB. */
575 #define MBA_CMPLT_5_16BIT 0x8035 /* Completion 5 16bit IOSB. */
576 #define MBA_CHG_IN_CONNECTION 0x8036 /* Change in connection mode. */
577 #define MBA_RIO_RESPONSE 0x8040 /* RIO response queue update. */
578 #define MBA_ZIO_RESPONSE 0x8040 /* ZIO response queue update. */
579 #define MBA_CMPLT_2_32BIT 0x8042 /* Completion 2 32bit IOSB. */
580 #define MBA_BYPASS_NOTIFICATION 0x8043 /* Auto bypass notification. */
581 #define MBA_DISCARD_RND_FRAME 0x8048 /* discard RND frame due to error. */
582 #define MBA_REJECTED_FCP_CMD 0x8049 /* rejected FCP_CMD. */
584 /* ISP mailbox loopback echo diagnostic error code */
585 #define MBS_LB_RESET 0x17
587 * Firmware options 1, 2, 3.
589 #define FO1_AE_ON_LIPF8 BIT_0
590 #define FO1_AE_ALL_LIP_RESET BIT_1
591 #define FO1_CTIO_RETRY BIT_3
592 #define FO1_DISABLE_LIP_F7_SW BIT_4
593 #define FO1_DISABLE_100MS_LOS_WAIT BIT_5
594 #define FO1_DISABLE_GPIO6_7 BIT_6 /* LED bits */
595 #define FO1_AE_ON_LOOP_INIT_ERR BIT_7
596 #define FO1_SET_EMPHASIS_SWING BIT_8
597 #define FO1_AE_AUTO_BYPASS BIT_9
598 #define FO1_ENABLE_PURE_IOCB BIT_10
599 #define FO1_AE_PLOGI_RJT BIT_11
600 #define FO1_ENABLE_ABORT_SEQUENCE BIT_12
601 #define FO1_AE_QUEUE_FULL BIT_13
603 #define FO2_ENABLE_ATIO_TYPE_3 BIT_0
604 #define FO2_REV_LOOPBACK BIT_1
606 #define FO3_ENABLE_EMERG_IOCB BIT_0
607 #define FO3_AE_RND_ERROR BIT_1
609 /* 24XX additional firmware options */
610 #define ADD_FO_COUNT 3
611 #define ADD_FO1_DISABLE_GPIO_LED_CTRL BIT_6 /* LED bits */
612 #define ADD_FO1_ENABLE_PUREX_IOCB BIT_10
614 #define ADD_FO2_ENABLE_SEL_CLS2 BIT_5
616 #define ADD_FO3_NO_ABT_ON_LINK_DOWN BIT_14
619 * ISP mailbox commands
621 #define MBC_LOAD_RAM 1 /* Load RAM. */
622 #define MBC_EXECUTE_FIRMWARE 2 /* Execute firmware. */
623 #define MBC_WRITE_RAM_WORD 4 /* Write RAM word. */
624 #define MBC_READ_RAM_WORD 5 /* Read RAM word. */
625 #define MBC_MAILBOX_REGISTER_TEST 6 /* Wrap incoming mailboxes */
626 #define MBC_VERIFY_CHECKSUM 7 /* Verify checksum. */
627 #define MBC_GET_FIRMWARE_VERSION 8 /* Get firmware revision. */
628 #define MBC_LOAD_RISC_RAM 9 /* Load RAM command. */
629 #define MBC_DUMP_RISC_RAM 0xa /* Dump RAM command. */
630 #define MBC_LOAD_RISC_RAM_EXTENDED 0xb /* Load RAM extended. */
631 #define MBC_DUMP_RISC_RAM_EXTENDED 0xc /* Dump RAM extended. */
632 #define MBC_WRITE_RAM_WORD_EXTENDED 0xd /* Write RAM word extended */
633 #define MBC_READ_RAM_EXTENDED 0xf /* Read RAM extended. */
634 #define MBC_IOCB_COMMAND 0x12 /* Execute IOCB command. */
635 #define MBC_STOP_FIRMWARE 0x14 /* Stop firmware. */
636 #define MBC_ABORT_COMMAND 0x15 /* Abort IOCB command. */
637 #define MBC_ABORT_DEVICE 0x16 /* Abort device (ID/LUN). */
638 #define MBC_ABORT_TARGET 0x17 /* Abort target (ID). */
639 #define MBC_RESET 0x18 /* Reset. */
640 #define MBC_GET_ADAPTER_LOOP_ID 0x20 /* Get loop id of ISP2200. */
641 #define MBC_GET_RETRY_COUNT 0x22 /* Get f/w retry cnt/delay. */
642 #define MBC_DISABLE_VI 0x24 /* Disable VI operation. */
643 #define MBC_ENABLE_VI 0x25 /* Enable VI operation. */
644 #define MBC_GET_FIRMWARE_OPTION 0x28 /* Get Firmware Options. */
645 #define MBC_SET_FIRMWARE_OPTION 0x38 /* Set Firmware Options. */
646 #define MBC_LOOP_PORT_BYPASS 0x40 /* Loop Port Bypass. */
647 #define MBC_LOOP_PORT_ENABLE 0x41 /* Loop Port Enable. */
648 #define MBC_GET_RESOURCE_COUNTS 0x42 /* Get Resource Counts. */
649 #define MBC_NON_PARTICIPATE 0x43 /* Non-Participating Mode. */
650 #define MBC_DIAGNOSTIC_ECHO 0x44 /* Diagnostic echo. */
651 #define MBC_DIAGNOSTIC_LOOP_BACK 0x45 /* Diagnostic loop back. */
652 #define MBC_ONLINE_SELF_TEST 0x46 /* Online self-test. */
653 #define MBC_ENHANCED_GET_PORT_DATABASE 0x47 /* Get port database + login */
654 #define MBC_RESET_LINK_STATUS 0x52 /* Reset Link Error Status */
655 #define MBC_IOCB_COMMAND_A64 0x54 /* Execute IOCB command (64) */
656 #define MBC_SEND_RNID_ELS 0x57 /* Send RNID ELS request */
657 #define MBC_SET_RNID_PARAMS 0x59 /* Set RNID parameters */
658 #define MBC_GET_RNID_PARAMS 0x5a /* Data Rate */
659 #define MBC_DATA_RATE 0x5d /* Get RNID parameters */
660 #define MBC_INITIALIZE_FIRMWARE 0x60 /* Initialize firmware */
661 #define MBC_INITIATE_LIP 0x62 /* Initiate Loop */
662 /* Initialization Procedure */
663 #define MBC_GET_FC_AL_POSITION_MAP 0x63 /* Get FC_AL Position Map. */
664 #define MBC_GET_PORT_DATABASE 0x64 /* Get Port Database. */
665 #define MBC_CLEAR_ACA 0x65 /* Clear ACA. */
666 #define MBC_TARGET_RESET 0x66 /* Target Reset. */
667 #define MBC_CLEAR_TASK_SET 0x67 /* Clear Task Set. */
668 #define MBC_ABORT_TASK_SET 0x68 /* Abort Task Set. */
669 #define MBC_GET_FIRMWARE_STATE 0x69 /* Get firmware state. */
670 #define MBC_GET_PORT_NAME 0x6a /* Get port name. */
671 #define MBC_GET_LINK_STATUS 0x6b /* Get port link status. */
672 #define MBC_LIP_RESET 0x6c /* LIP reset. */
673 #define MBC_SEND_SNS_COMMAND 0x6e /* Send Simple Name Server */
675 #define MBC_LOGIN_FABRIC_PORT 0x6f /* Login fabric port. */
676 #define MBC_SEND_CHANGE_REQUEST 0x70 /* Send Change Request. */
677 #define MBC_LOGOUT_FABRIC_PORT 0x71 /* Logout fabric port. */
678 #define MBC_LIP_FULL_LOGIN 0x72 /* Full login LIP. */
679 #define MBC_LOGIN_LOOP_PORT 0x74 /* Login Loop Port. */
680 #define MBC_PORT_NODE_NAME_LIST 0x75 /* Get port/node name list. */
681 #define MBC_INITIALIZE_RECEIVE_QUEUE 0x77 /* Initialize receive queue */
682 #define MBC_UNLOAD_IP 0x79 /* Shutdown IP */
683 #define MBC_GET_ID_LIST 0x7C /* Get Port ID list. */
684 #define MBC_SEND_LFA_COMMAND 0x7D /* Send Loop Fabric Address */
685 #define MBC_LUN_RESET 0x7E /* Send LUN reset */
688 * ISP24xx mailbox commands
690 #define MBC_SERDES_PARAMS 0x10 /* Serdes Tx Parameters. */
691 #define MBC_GET_IOCB_STATUS 0x12 /* Get IOCB status command. */
692 #define MBC_PORT_PARAMS 0x1A /* Port iDMA Parameters. */
693 #define MBC_GET_TIMEOUT_PARAMS 0x22 /* Get FW timeouts. */
694 #define MBC_TRACE_CONTROL 0x27 /* Trace control command. */
695 #define MBC_GEN_SYSTEM_ERROR 0x2a /* Generate System Error. */
696 #define MBC_WRITE_SFP 0x30 /* Write SFP Data. */
697 #define MBC_READ_SFP 0x31 /* Read SFP Data. */
698 #define MBC_SET_TIMEOUT_PARAMS 0x32 /* Set FW timeouts. */
699 #define MBC_MID_INITIALIZE_FIRMWARE 0x48 /* MID Initialize firmware. */
700 #define MBC_MID_GET_VP_DATABASE 0x49 /* MID Get VP Database. */
701 #define MBC_MID_GET_VP_ENTRY 0x4a /* MID Get VP Entry. */
702 #define MBC_HOST_MEMORY_COPY 0x53 /* Host Memory Copy. */
703 #define MBC_SEND_RNFT_ELS 0x5e /* Send RNFT ELS request */
704 #define MBC_GET_LINK_PRIV_STATS 0x6d /* Get link & private data. */
705 #define MBC_SET_VENDOR_ID 0x76 /* Set Vendor ID. */
706 #define MBC_SET_PORT_CONFIG 0x122 /* Set port configuration */
707 #define MBC_GET_PORT_CONFIG 0x123 /* Get port configuration */
710 * ISP81xx mailbox commands
712 #define MBC_WRITE_MPI_REGISTER 0x01 /* Write MPI Register. */
714 /* Firmware return data sizes */
715 #define FCAL_MAP_SIZE 128
717 /* Mailbox bit definitions for out_mb and in_mb */
718 #define MBX_31 BIT_31
719 #define MBX_30 BIT_30
720 #define MBX_29 BIT_29
721 #define MBX_28 BIT_28
722 #define MBX_27 BIT_27
723 #define MBX_26 BIT_26
724 #define MBX_25 BIT_25
725 #define MBX_24 BIT_24
726 #define MBX_23 BIT_23
727 #define MBX_22 BIT_22
728 #define MBX_21 BIT_21
729 #define MBX_20 BIT_20
730 #define MBX_19 BIT_19
731 #define MBX_18 BIT_18
732 #define MBX_17 BIT_17
733 #define MBX_16 BIT_16
734 #define MBX_15 BIT_15
735 #define MBX_14 BIT_14
736 #define MBX_13 BIT_13
737 #define MBX_12 BIT_12
738 #define MBX_11 BIT_11
739 #define MBX_10 BIT_10
752 * Firmware state codes from get firmware state mailbox command
754 #define FSTATE_CONFIG_WAIT 0
755 #define FSTATE_WAIT_AL_PA 1
756 #define FSTATE_WAIT_LOGIN 2
757 #define FSTATE_READY 3
758 #define FSTATE_LOSS_OF_SYNC 4
759 #define FSTATE_ERROR 5
760 #define FSTATE_REINIT 6
761 #define FSTATE_NON_PART 7
763 #define FSTATE_CONFIG_CORRECT 0
764 #define FSTATE_P2P_RCV_LIP 1
765 #define FSTATE_P2P_CHOOSE_LOOP 2
766 #define FSTATE_P2P_RCV_UNIDEN_LIP 3
767 #define FSTATE_FATAL_ERROR 4
768 #define FSTATE_LOOP_BACK_CONN 5
771 * Port Database structure definition
772 * Little endian except where noted.
774 #define PORT_DATABASE_SIZE 128 /* bytes */
778 uint8_t master_state
;
781 uint8_t hard_address
;
784 uint8_t node_name
[WWN_SIZE
];
785 uint8_t port_name
[WWN_SIZE
];
786 uint16_t execution_throttle
;
787 uint16_t execution_count
;
790 uint16_t resource_allocation
;
791 uint16_t current_allocation
;
794 uint16_t transmit_execution_list_next
;
795 uint16_t transmit_execution_list_previous
;
796 uint16_t common_features
;
797 uint16_t total_concurrent_sequences
;
798 uint16_t RO_by_information_category
;
801 uint16_t receive_data_size
;
802 uint16_t concurrent_sequences
;
803 uint16_t open_sequences_per_exchange
;
804 uint16_t lun_abort_flags
;
805 uint16_t lun_stop_flags
;
806 uint16_t stop_queue_head
;
807 uint16_t stop_queue_tail
;
808 uint16_t port_retry_timer
;
809 uint16_t next_sequence_id
;
810 uint16_t frame_count
;
811 uint16_t PRLI_payload_length
;
812 uint8_t prli_svc_param_word_0
[2]; /* Big endian */
813 /* Bits 15-0 of word 0 */
814 uint8_t prli_svc_param_word_3
[2]; /* Big endian */
815 /* Bits 15-0 of word 3 */
817 uint16_t extended_lun_info_list_pointer
;
818 uint16_t extended_lun_stop_list_pointer
;
822 * Port database slave/master states
824 #define PD_STATE_DISCOVERY 0
825 #define PD_STATE_WAIT_DISCOVERY_ACK 1
826 #define PD_STATE_PORT_LOGIN 2
827 #define PD_STATE_WAIT_PORT_LOGIN_ACK 3
828 #define PD_STATE_PROCESS_LOGIN 4
829 #define PD_STATE_WAIT_PROCESS_LOGIN_ACK 5
830 #define PD_STATE_PORT_LOGGED_IN 6
831 #define PD_STATE_PORT_UNAVAILABLE 7
832 #define PD_STATE_PROCESS_LOGOUT 8
833 #define PD_STATE_WAIT_PROCESS_LOGOUT_ACK 9
834 #define PD_STATE_PORT_LOGOUT 10
835 #define PD_STATE_WAIT_PORT_LOGOUT_ACK 11
838 #define QLA_ZIO_MODE_6 (BIT_2 | BIT_1)
839 #define QLA_ZIO_DISABLED 0
840 #define QLA_ZIO_DEFAULT_TIMER 2
843 * ISP Initialization Control Block.
844 * Little endian except where noted.
846 #define ICB_VERSION 1
852 * LSB BIT 0 = Enable Hard Loop Id
853 * LSB BIT 1 = Enable Fairness
854 * LSB BIT 2 = Enable Full-Duplex
855 * LSB BIT 3 = Enable Fast Posting
856 * LSB BIT 4 = Enable Target Mode
857 * LSB BIT 5 = Disable Initiator Mode
858 * LSB BIT 6 = Enable ADISC
859 * LSB BIT 7 = Enable Target Inquiry Data
861 * MSB BIT 0 = Enable PDBC Notify
862 * MSB BIT 1 = Non Participating LIP
863 * MSB BIT 2 = Descending Loop ID Search
864 * MSB BIT 3 = Acquire Loop ID in LIPA
865 * MSB BIT 4 = Stop PortQ on Full Status
866 * MSB BIT 5 = Full Login after LIP
867 * MSB BIT 6 = Node Name Option
868 * MSB BIT 7 = Ext IFWCB enable bit
870 uint8_t firmware_options
[2];
872 uint16_t frame_payload_size
;
873 uint16_t max_iocb_allocation
;
874 uint16_t execution_throttle
;
876 uint8_t retry_delay
; /* unused */
877 uint8_t port_name
[WWN_SIZE
]; /* Big endian. */
878 uint16_t hard_address
;
879 uint8_t inquiry_data
;
880 uint8_t login_timeout
;
881 uint8_t node_name
[WWN_SIZE
]; /* Big endian. */
883 uint16_t request_q_outpointer
;
884 uint16_t response_q_inpointer
;
885 uint16_t request_q_length
;
886 uint16_t response_q_length
;
887 uint32_t request_q_address
[2];
888 uint32_t response_q_address
[2];
890 uint16_t lun_enables
;
891 uint8_t command_resource_count
;
892 uint8_t immediate_notify_resource_count
;
894 uint8_t reserved_2
[2];
897 * LSB BIT 0 = Timer Operation mode bit 0
898 * LSB BIT 1 = Timer Operation mode bit 1
899 * LSB BIT 2 = Timer Operation mode bit 2
900 * LSB BIT 3 = Timer Operation mode bit 3
901 * LSB BIT 4 = Init Config Mode bit 0
902 * LSB BIT 5 = Init Config Mode bit 1
903 * LSB BIT 6 = Init Config Mode bit 2
904 * LSB BIT 7 = Enable Non part on LIHA failure
906 * MSB BIT 0 = Enable class 2
907 * MSB BIT 1 = Enable ACK0
910 * MSB BIT 4 = FC Tape Enable
911 * MSB BIT 5 = Enable FC Confirm
912 * MSB BIT 6 = Enable command queuing in target mode
913 * MSB BIT 7 = No Logo On Link Down
915 uint8_t add_firmware_options
[2];
917 uint8_t response_accumulation_timer
;
918 uint8_t interrupt_delay_timer
;
921 * LSB BIT 0 = Enable Read xfr_rdy
922 * LSB BIT 1 = Soft ID only
925 * LSB BIT 4 = FCP RSP Payload [0]
926 * LSB BIT 5 = FCP RSP Payload [1] / Sbus enable - 2200
927 * LSB BIT 6 = Enable Out-of-Order frame handling
928 * LSB BIT 7 = Disable Automatic PLOGI on Local Loop
930 * MSB BIT 0 = Sbus enable - 2300
934 * MSB BIT 4 = LED mode
935 * MSB BIT 5 = enable 50 ohm termination
936 * MSB BIT 6 = Data Rate (2300 only)
937 * MSB BIT 7 = Data Rate (2300 only)
939 uint8_t special_options
[2];
941 uint8_t reserved_3
[26];
945 * Get Link Status mailbox command return buffer.
947 #define GLSO_SEND_RPS BIT_0
948 #define GLSO_USE_DID BIT_3
950 struct link_statistics
{
951 uint32_t link_fail_cnt
;
952 uint32_t loss_sync_cnt
;
953 uint32_t loss_sig_cnt
;
954 uint32_t prim_seq_err_cnt
;
955 uint32_t inval_xmit_word_cnt
;
956 uint32_t inval_crc_cnt
;
958 uint32_t unused1
[0x1a];
961 uint32_t dumped_frames
;
967 * NVRAM Command values.
969 #define NV_START_BIT BIT_2
970 #define NV_WRITE_OP (BIT_26+BIT_24)
971 #define NV_READ_OP (BIT_26+BIT_25)
972 #define NV_ERASE_OP (BIT_26+BIT_25+BIT_24)
973 #define NV_MASK_OP (BIT_26+BIT_25+BIT_24)
974 #define NV_DELAY_COUNT 10
977 * QLogic ISP2100, ISP2200 and ISP2300 NVRAM structure definition.
984 uint8_t nvram_version
;
988 * NVRAM RISC parameter block
990 uint8_t parameter_block_version
;
994 * LSB BIT 0 = Enable Hard Loop Id
995 * LSB BIT 1 = Enable Fairness
996 * LSB BIT 2 = Enable Full-Duplex
997 * LSB BIT 3 = Enable Fast Posting
998 * LSB BIT 4 = Enable Target Mode
999 * LSB BIT 5 = Disable Initiator Mode
1000 * LSB BIT 6 = Enable ADISC
1001 * LSB BIT 7 = Enable Target Inquiry Data
1003 * MSB BIT 0 = Enable PDBC Notify
1004 * MSB BIT 1 = Non Participating LIP
1005 * MSB BIT 2 = Descending Loop ID Search
1006 * MSB BIT 3 = Acquire Loop ID in LIPA
1007 * MSB BIT 4 = Stop PortQ on Full Status
1008 * MSB BIT 5 = Full Login after LIP
1009 * MSB BIT 6 = Node Name Option
1010 * MSB BIT 7 = Ext IFWCB enable bit
1012 uint8_t firmware_options
[2];
1014 uint16_t frame_payload_size
;
1015 uint16_t max_iocb_allocation
;
1016 uint16_t execution_throttle
;
1017 uint8_t retry_count
;
1018 uint8_t retry_delay
; /* unused */
1019 uint8_t port_name
[WWN_SIZE
]; /* Big endian. */
1020 uint16_t hard_address
;
1021 uint8_t inquiry_data
;
1022 uint8_t login_timeout
;
1023 uint8_t node_name
[WWN_SIZE
]; /* Big endian. */
1026 * LSB BIT 0 = Timer Operation mode bit 0
1027 * LSB BIT 1 = Timer Operation mode bit 1
1028 * LSB BIT 2 = Timer Operation mode bit 2
1029 * LSB BIT 3 = Timer Operation mode bit 3
1030 * LSB BIT 4 = Init Config Mode bit 0
1031 * LSB BIT 5 = Init Config Mode bit 1
1032 * LSB BIT 6 = Init Config Mode bit 2
1033 * LSB BIT 7 = Enable Non part on LIHA failure
1035 * MSB BIT 0 = Enable class 2
1036 * MSB BIT 1 = Enable ACK0
1039 * MSB BIT 4 = FC Tape Enable
1040 * MSB BIT 5 = Enable FC Confirm
1041 * MSB BIT 6 = Enable command queuing in target mode
1042 * MSB BIT 7 = No Logo On Link Down
1044 uint8_t add_firmware_options
[2];
1046 uint8_t response_accumulation_timer
;
1047 uint8_t interrupt_delay_timer
;
1050 * LSB BIT 0 = Enable Read xfr_rdy
1051 * LSB BIT 1 = Soft ID only
1054 * LSB BIT 4 = FCP RSP Payload [0]
1055 * LSB BIT 5 = FCP RSP Payload [1] / Sbus enable - 2200
1056 * LSB BIT 6 = Enable Out-of-Order frame handling
1057 * LSB BIT 7 = Disable Automatic PLOGI on Local Loop
1059 * MSB BIT 0 = Sbus enable - 2300
1063 * MSB BIT 4 = LED mode
1064 * MSB BIT 5 = enable 50 ohm termination
1065 * MSB BIT 6 = Data Rate (2300 only)
1066 * MSB BIT 7 = Data Rate (2300 only)
1068 uint8_t special_options
[2];
1070 /* Reserved for expanded RISC parameter block */
1071 uint8_t reserved_2
[22];
1074 * LSB BIT 0 = Tx Sensitivity 1G bit 0
1075 * LSB BIT 1 = Tx Sensitivity 1G bit 1
1076 * LSB BIT 2 = Tx Sensitivity 1G bit 2
1077 * LSB BIT 3 = Tx Sensitivity 1G bit 3
1078 * LSB BIT 4 = Rx Sensitivity 1G bit 0
1079 * LSB BIT 5 = Rx Sensitivity 1G bit 1
1080 * LSB BIT 6 = Rx Sensitivity 1G bit 2
1081 * LSB BIT 7 = Rx Sensitivity 1G bit 3
1083 * MSB BIT 0 = Tx Sensitivity 2G bit 0
1084 * MSB BIT 1 = Tx Sensitivity 2G bit 1
1085 * MSB BIT 2 = Tx Sensitivity 2G bit 2
1086 * MSB BIT 3 = Tx Sensitivity 2G bit 3
1087 * MSB BIT 4 = Rx Sensitivity 2G bit 0
1088 * MSB BIT 5 = Rx Sensitivity 2G bit 1
1089 * MSB BIT 6 = Rx Sensitivity 2G bit 2
1090 * MSB BIT 7 = Rx Sensitivity 2G bit 3
1092 * LSB BIT 0 = Output Swing 1G bit 0
1093 * LSB BIT 1 = Output Swing 1G bit 1
1094 * LSB BIT 2 = Output Swing 1G bit 2
1095 * LSB BIT 3 = Output Emphasis 1G bit 0
1096 * LSB BIT 4 = Output Emphasis 1G bit 1
1097 * LSB BIT 5 = Output Swing 2G bit 0
1098 * LSB BIT 6 = Output Swing 2G bit 1
1099 * LSB BIT 7 = Output Swing 2G bit 2
1101 * MSB BIT 0 = Output Emphasis 2G bit 0
1102 * MSB BIT 1 = Output Emphasis 2G bit 1
1103 * MSB BIT 2 = Output Enable
1110 uint8_t seriallink_options
[4];
1113 * NVRAM host parameter block
1115 * LSB BIT 0 = Enable spinup delay
1116 * LSB BIT 1 = Disable BIOS
1117 * LSB BIT 2 = Enable Memory Map BIOS
1118 * LSB BIT 3 = Enable Selectable Boot
1119 * LSB BIT 4 = Disable RISC code load
1120 * LSB BIT 5 = Set cache line size 1
1121 * LSB BIT 6 = PCI Parity Disable
1122 * LSB BIT 7 = Enable extended logging
1124 * MSB BIT 0 = Enable 64bit addressing
1125 * MSB BIT 1 = Enable lip reset
1126 * MSB BIT 2 = Enable lip full login
1127 * MSB BIT 3 = Enable target reset
1128 * MSB BIT 4 = Enable database storage
1129 * MSB BIT 5 = Enable cache flush read
1130 * MSB BIT 6 = Enable database load
1131 * MSB BIT 7 = Enable alternate WWN
1135 uint8_t boot_node_name
[WWN_SIZE
];
1136 uint8_t boot_lun_number
;
1137 uint8_t reset_delay
;
1138 uint8_t port_down_retry_count
;
1139 uint8_t boot_id_number
;
1140 uint16_t max_luns_per_target
;
1141 uint8_t fcode_boot_port_name
[WWN_SIZE
];
1142 uint8_t alternate_port_name
[WWN_SIZE
];
1143 uint8_t alternate_node_name
[WWN_SIZE
];
1146 * BIT 0 = Selective Login
1147 * BIT 1 = Alt-Boot Enable
1149 * BIT 3 = Boot Order List
1151 * BIT 5 = Selective LUN
1155 uint8_t efi_parameters
;
1157 uint8_t link_down_timeout
;
1159 uint8_t adapter_id
[16];
1161 uint8_t alt1_boot_node_name
[WWN_SIZE
];
1162 uint16_t alt1_boot_lun_number
;
1163 uint8_t alt2_boot_node_name
[WWN_SIZE
];
1164 uint16_t alt2_boot_lun_number
;
1165 uint8_t alt3_boot_node_name
[WWN_SIZE
];
1166 uint16_t alt3_boot_lun_number
;
1167 uint8_t alt4_boot_node_name
[WWN_SIZE
];
1168 uint16_t alt4_boot_lun_number
;
1169 uint8_t alt5_boot_node_name
[WWN_SIZE
];
1170 uint16_t alt5_boot_lun_number
;
1171 uint8_t alt6_boot_node_name
[WWN_SIZE
];
1172 uint16_t alt6_boot_lun_number
;
1173 uint8_t alt7_boot_node_name
[WWN_SIZE
];
1174 uint16_t alt7_boot_lun_number
;
1176 uint8_t reserved_3
[2];
1178 /* Offset 200-215 : Model Number */
1179 uint8_t model_number
[16];
1181 /* OEM related items */
1182 uint8_t oem_specific
[16];
1185 * NVRAM Adapter Features offset 232-239
1187 * LSB BIT 0 = External GBIC
1188 * LSB BIT 1 = Risc RAM parity
1189 * LSB BIT 2 = Buffer Plus Module
1190 * LSB BIT 3 = Multi Chip Adapter
1191 * LSB BIT 4 = Internal connector
1205 uint8_t adapter_features
[2];
1207 uint8_t reserved_4
[16];
1209 /* Subsystem vendor ID for ISP2200 */
1210 uint16_t subsystem_vendor_id_2200
;
1212 /* Subsystem device ID for ISP2200 */
1213 uint16_t subsystem_device_id_2200
;
1220 * ISP queue - response queue entry definition.
1225 #define RESPONSE_PROCESSED 0xDEADDEAD /* Signature */
1236 #define SET_TARGET_ID(ha, to, from) \
1238 if (HAS_EXTENDED_IDS(ha)) \
1239 to.extended = cpu_to_le16(from); \
1241 to.id.standard = (uint8_t)from; \
1245 * ISP queue - command entry structure definition.
1247 #define COMMAND_TYPE 0x11 /* Command entry */
1249 uint8_t entry_type
; /* Entry type. */
1250 uint8_t entry_count
; /* Entry count. */
1251 uint8_t sys_define
; /* System defined. */
1252 uint8_t entry_status
; /* Entry Status. */
1253 uint32_t handle
; /* System handle. */
1254 target_id_t target
; /* SCSI ID */
1255 uint16_t lun
; /* SCSI LUN */
1256 uint16_t control_flags
; /* Control flags. */
1257 #define CF_WRITE BIT_6
1258 #define CF_READ BIT_5
1259 #define CF_SIMPLE_TAG BIT_3
1260 #define CF_ORDERED_TAG BIT_2
1261 #define CF_HEAD_TAG BIT_1
1262 uint16_t reserved_1
;
1263 uint16_t timeout
; /* Command timeout. */
1264 uint16_t dseg_count
; /* Data segment count. */
1265 uint8_t scsi_cdb
[MAX_CMDSZ
]; /* SCSI command words. */
1266 uint32_t byte_count
; /* Total byte count. */
1267 uint32_t dseg_0_address
; /* Data segment 0 address. */
1268 uint32_t dseg_0_length
; /* Data segment 0 length. */
1269 uint32_t dseg_1_address
; /* Data segment 1 address. */
1270 uint32_t dseg_1_length
; /* Data segment 1 length. */
1271 uint32_t dseg_2_address
; /* Data segment 2 address. */
1272 uint32_t dseg_2_length
; /* Data segment 2 length. */
1276 * ISP queue - 64-Bit addressing, command entry structure definition.
1278 #define COMMAND_A64_TYPE 0x19 /* Command A64 entry */
1280 uint8_t entry_type
; /* Entry type. */
1281 uint8_t entry_count
; /* Entry count. */
1282 uint8_t sys_define
; /* System defined. */
1283 uint8_t entry_status
; /* Entry Status. */
1284 uint32_t handle
; /* System handle. */
1285 target_id_t target
; /* SCSI ID */
1286 uint16_t lun
; /* SCSI LUN */
1287 uint16_t control_flags
; /* Control flags. */
1288 uint16_t reserved_1
;
1289 uint16_t timeout
; /* Command timeout. */
1290 uint16_t dseg_count
; /* Data segment count. */
1291 uint8_t scsi_cdb
[MAX_CMDSZ
]; /* SCSI command words. */
1292 uint32_t byte_count
; /* Total byte count. */
1293 uint32_t dseg_0_address
[2]; /* Data segment 0 address. */
1294 uint32_t dseg_0_length
; /* Data segment 0 length. */
1295 uint32_t dseg_1_address
[2]; /* Data segment 1 address. */
1296 uint32_t dseg_1_length
; /* Data segment 1 length. */
1297 } cmd_a64_entry_t
, request_t
;
1300 * ISP queue - continuation entry structure definition.
1302 #define CONTINUE_TYPE 0x02 /* Continuation entry. */
1304 uint8_t entry_type
; /* Entry type. */
1305 uint8_t entry_count
; /* Entry count. */
1306 uint8_t sys_define
; /* System defined. */
1307 uint8_t entry_status
; /* Entry Status. */
1309 uint32_t dseg_0_address
; /* Data segment 0 address. */
1310 uint32_t dseg_0_length
; /* Data segment 0 length. */
1311 uint32_t dseg_1_address
; /* Data segment 1 address. */
1312 uint32_t dseg_1_length
; /* Data segment 1 length. */
1313 uint32_t dseg_2_address
; /* Data segment 2 address. */
1314 uint32_t dseg_2_length
; /* Data segment 2 length. */
1315 uint32_t dseg_3_address
; /* Data segment 3 address. */
1316 uint32_t dseg_3_length
; /* Data segment 3 length. */
1317 uint32_t dseg_4_address
; /* Data segment 4 address. */
1318 uint32_t dseg_4_length
; /* Data segment 4 length. */
1319 uint32_t dseg_5_address
; /* Data segment 5 address. */
1320 uint32_t dseg_5_length
; /* Data segment 5 length. */
1321 uint32_t dseg_6_address
; /* Data segment 6 address. */
1322 uint32_t dseg_6_length
; /* Data segment 6 length. */
1326 * ISP queue - 64-Bit addressing, continuation entry structure definition.
1328 #define CONTINUE_A64_TYPE 0x0A /* Continuation A64 entry. */
1330 uint8_t entry_type
; /* Entry type. */
1331 uint8_t entry_count
; /* Entry count. */
1332 uint8_t sys_define
; /* System defined. */
1333 uint8_t entry_status
; /* Entry Status. */
1334 uint32_t dseg_0_address
[2]; /* Data segment 0 address. */
1335 uint32_t dseg_0_length
; /* Data segment 0 length. */
1336 uint32_t dseg_1_address
[2]; /* Data segment 1 address. */
1337 uint32_t dseg_1_length
; /* Data segment 1 length. */
1338 uint32_t dseg_2_address
[2]; /* Data segment 2 address. */
1339 uint32_t dseg_2_length
; /* Data segment 2 length. */
1340 uint32_t dseg_3_address
[2]; /* Data segment 3 address. */
1341 uint32_t dseg_3_length
; /* Data segment 3 length. */
1342 uint32_t dseg_4_address
[2]; /* Data segment 4 address. */
1343 uint32_t dseg_4_length
; /* Data segment 4 length. */
1346 #define PO_MODE_DIF_INSERT 0
1347 #define PO_MODE_DIF_REMOVE BIT_0
1348 #define PO_MODE_DIF_PASS BIT_1
1349 #define PO_MODE_DIF_REPLACE (BIT_0 + BIT_1)
1350 #define PO_ENABLE_DIF_BUNDLING BIT_8
1351 #define PO_ENABLE_INCR_GUARD_SEED BIT_3
1352 #define PO_DISABLE_INCR_REF_TAG BIT_5
1353 #define PO_DISABLE_GUARD_CHECK BIT_4
1355 * ISP queue - 64-Bit addressing, continuation crc entry structure definition.
1357 struct crc_context
{
1358 uint32_t handle
; /* System handle. */
1361 uint8_t ref_tag_mask
[4]; /* Validation/Replacement Mask*/
1362 uint8_t app_tag_mask
[2]; /* Validation/Replacement Mask*/
1363 uint16_t guard_seed
; /* Initial Guard Seed */
1364 uint16_t prot_opts
; /* Requested Data Protection Mode */
1365 uint16_t blk_size
; /* Data size in bytes */
1366 uint16_t runt_blk_guard
; /* Guard value for runt block (tape
1368 uint32_t byte_count
; /* Total byte count/ total data
1372 uint32_t reserved_1
;
1373 uint16_t reserved_2
;
1374 uint16_t reserved_3
;
1375 uint32_t reserved_4
;
1376 uint32_t data_address
[2];
1377 uint32_t data_length
;
1378 uint32_t reserved_5
[2];
1379 uint32_t reserved_6
;
1382 uint32_t dif_byte_count
; /* Total DIF byte
1384 uint16_t reserved_1
;
1385 uint16_t dseg_count
; /* Data segment count */
1386 uint32_t reserved_2
;
1387 uint32_t data_address
[2];
1388 uint32_t data_length
;
1389 uint32_t dif_address
[2];
1390 uint32_t dif_length
; /* Data segment 0
1395 struct fcp_cmnd fcp_cmnd
;
1396 dma_addr_t crc_ctx_dma
;
1397 /* List of DMA context transfers */
1398 struct list_head dsd_list
;
1400 /* This structure should not exceed 512 bytes */
1403 #define CRC_CONTEXT_LEN_FW (offsetof(struct crc_context, fcp_cmnd.lun))
1404 #define CRC_CONTEXT_FCPCMND_OFF (offsetof(struct crc_context, fcp_cmnd.lun))
1407 * ISP queue - status entry structure definition.
1409 #define STATUS_TYPE 0x03 /* Status entry. */
1411 uint8_t entry_type
; /* Entry type. */
1412 uint8_t entry_count
; /* Entry count. */
1413 uint8_t sys_define
; /* System defined. */
1414 uint8_t entry_status
; /* Entry Status. */
1415 uint32_t handle
; /* System handle. */
1416 uint16_t scsi_status
; /* SCSI status. */
1417 uint16_t comp_status
; /* Completion status. */
1418 uint16_t state_flags
; /* State flags. */
1419 uint16_t status_flags
; /* Status flags. */
1420 uint16_t rsp_info_len
; /* Response Info Length. */
1421 uint16_t req_sense_length
; /* Request sense data length. */
1422 uint32_t residual_length
; /* Residual transfer length. */
1423 uint8_t rsp_info
[8]; /* FCP response information. */
1424 uint8_t req_sense_data
[32]; /* Request sense data. */
1428 * Status entry entry status
1430 #define RF_RQ_DMA_ERROR BIT_6 /* Request Queue DMA error. */
1431 #define RF_INV_E_ORDER BIT_5 /* Invalid entry order. */
1432 #define RF_INV_E_COUNT BIT_4 /* Invalid entry count. */
1433 #define RF_INV_E_PARAM BIT_3 /* Invalid entry parameter. */
1434 #define RF_INV_E_TYPE BIT_2 /* Invalid entry type. */
1435 #define RF_BUSY BIT_1 /* Busy */
1436 #define RF_MASK (RF_RQ_DMA_ERROR | RF_INV_E_ORDER | RF_INV_E_COUNT | \
1437 RF_INV_E_PARAM | RF_INV_E_TYPE | RF_BUSY)
1438 #define RF_MASK_24XX (RF_INV_E_ORDER | RF_INV_E_COUNT | RF_INV_E_PARAM | \
1442 * Status entry SCSI status bit definitions.
1444 #define SS_MASK 0xfff /* Reserved bits BIT_12-BIT_15*/
1445 #define SS_RESIDUAL_UNDER BIT_11
1446 #define SS_RESIDUAL_OVER BIT_10
1447 #define SS_SENSE_LEN_VALID BIT_9
1448 #define SS_RESPONSE_INFO_LEN_VALID BIT_8
1450 #define SS_RESERVE_CONFLICT (BIT_4 | BIT_3)
1451 #define SS_BUSY_CONDITION BIT_3
1452 #define SS_CONDITION_MET BIT_2
1453 #define SS_CHECK_CONDITION BIT_1
1456 * Status entry completion status
1458 #define CS_COMPLETE 0x0 /* No errors */
1459 #define CS_INCOMPLETE 0x1 /* Incomplete transfer of cmd. */
1460 #define CS_DMA 0x2 /* A DMA direction error. */
1461 #define CS_TRANSPORT 0x3 /* Transport error. */
1462 #define CS_RESET 0x4 /* SCSI bus reset occurred */
1463 #define CS_ABORTED 0x5 /* System aborted command. */
1464 #define CS_TIMEOUT 0x6 /* Timeout error. */
1465 #define CS_DATA_OVERRUN 0x7 /* Data overrun. */
1466 #define CS_DIF_ERROR 0xC /* DIF error detected */
1468 #define CS_DATA_UNDERRUN 0x15 /* Data Underrun. */
1469 #define CS_QUEUE_FULL 0x1C /* Queue Full. */
1470 #define CS_PORT_UNAVAILABLE 0x28 /* Port unavailable */
1471 /* (selection timeout) */
1472 #define CS_PORT_LOGGED_OUT 0x29 /* Port Logged Out */
1473 #define CS_PORT_CONFIG_CHG 0x2A /* Port Configuration Changed */
1474 #define CS_PORT_BUSY 0x2B /* Port Busy */
1475 #define CS_COMPLETE_CHKCOND 0x30 /* Error? */
1476 #define CS_BAD_PAYLOAD 0x80 /* Driver defined */
1477 #define CS_UNKNOWN 0x81 /* Driver defined */
1478 #define CS_RETRY 0x82 /* Driver defined */
1479 #define CS_LOOP_DOWN_ABORT 0x83 /* Driver defined */
1482 * Status entry status flags
1484 #define SF_ABTS_TERMINATED BIT_10
1485 #define SF_LOGOUT_SENT BIT_13
1488 * ISP queue - status continuation entry structure definition.
1490 #define STATUS_CONT_TYPE 0x10 /* Status continuation entry. */
1492 uint8_t entry_type
; /* Entry type. */
1493 uint8_t entry_count
; /* Entry count. */
1494 uint8_t sys_define
; /* System defined. */
1495 uint8_t entry_status
; /* Entry Status. */
1496 uint8_t data
[60]; /* data */
1500 * ISP queue - RIO Type 1 status entry (32 bit I/O entry handles)
1501 * structure definition.
1503 #define STATUS_TYPE_21 0x21 /* Status entry. */
1505 uint8_t entry_type
; /* Entry type. */
1506 uint8_t entry_count
; /* Entry count. */
1507 uint8_t handle_count
; /* Handle count. */
1508 uint8_t entry_status
; /* Entry Status. */
1509 uint32_t handle
[15]; /* System handles. */
1513 * ISP queue - RIO Type 2 status entry (16 bit I/O entry handles)
1514 * structure definition.
1516 #define STATUS_TYPE_22 0x22 /* Status entry. */
1518 uint8_t entry_type
; /* Entry type. */
1519 uint8_t entry_count
; /* Entry count. */
1520 uint8_t handle_count
; /* Handle count. */
1521 uint8_t entry_status
; /* Entry Status. */
1522 uint16_t handle
[30]; /* System handles. */
1526 * ISP queue - marker entry structure definition.
1528 #define MARKER_TYPE 0x04 /* Marker entry. */
1530 uint8_t entry_type
; /* Entry type. */
1531 uint8_t entry_count
; /* Entry count. */
1532 uint8_t handle_count
; /* Handle count. */
1533 uint8_t entry_status
; /* Entry Status. */
1534 uint32_t sys_define_2
; /* System defined. */
1535 target_id_t target
; /* SCSI ID */
1536 uint8_t modifier
; /* Modifier (7-0). */
1537 #define MK_SYNC_ID_LUN 0 /* Synchronize ID/LUN */
1538 #define MK_SYNC_ID 1 /* Synchronize ID */
1539 #define MK_SYNC_ALL 2 /* Synchronize all ID/LUN */
1540 #define MK_SYNC_LIP 3 /* Synchronize all ID/LUN, */
1541 /* clear port changed, */
1542 /* use sequence number. */
1544 uint16_t sequence_number
; /* Sequence number of event */
1545 uint16_t lun
; /* SCSI LUN */
1546 uint8_t reserved_2
[48];
1550 * ISP queue - Management Server entry structure definition.
1552 #define MS_IOCB_TYPE 0x29 /* Management Server IOCB entry */
1554 uint8_t entry_type
; /* Entry type. */
1555 uint8_t entry_count
; /* Entry count. */
1556 uint8_t handle_count
; /* Handle count. */
1557 uint8_t entry_status
; /* Entry Status. */
1558 uint32_t handle1
; /* System handle. */
1559 target_id_t loop_id
;
1561 uint16_t control_flags
; /* Control flags. */
1564 uint16_t cmd_dsd_count
;
1565 uint16_t total_dsd_count
;
1571 uint32_t rsp_bytecount
;
1572 uint32_t req_bytecount
;
1573 uint32_t dseg_req_address
[2]; /* Data segment 0 address. */
1574 uint32_t dseg_req_length
; /* Data segment 0 length. */
1575 uint32_t dseg_rsp_address
[2]; /* Data segment 1 address. */
1576 uint32_t dseg_rsp_length
; /* Data segment 1 length. */
1581 * ISP queue - Mailbox Command entry structure definition.
1583 #define MBX_IOCB_TYPE 0x39
1586 uint8_t entry_count
;
1587 uint8_t sys_define1
;
1588 /* Use sys_define1 for source type */
1589 #define SOURCE_SCSI 0x00
1590 #define SOURCE_IP 0x01
1591 #define SOURCE_VI 0x02
1592 #define SOURCE_SCTP 0x03
1593 #define SOURCE_MP 0x04
1594 #define SOURCE_MPIOCTL 0x05
1595 #define SOURCE_ASYNC_IOCB 0x07
1597 uint8_t entry_status
;
1600 target_id_t loop_id
;
1603 uint16_t state_flags
;
1604 uint16_t status_flags
;
1606 uint32_t sys_define2
[2];
1616 uint32_t reserved_2
[2];
1617 uint8_t node_name
[WWN_SIZE
];
1618 uint8_t port_name
[WWN_SIZE
];
1622 * ISP request and response queue entry sizes
1624 #define RESPONSE_ENTRY_SIZE (sizeof(response_t))
1625 #define REQUEST_ENTRY_SIZE (sizeof(request_t))
1629 * 24 bit port ID type definition.
1639 #elif defined(__LITTLE_ENDIAN)
1644 #error "__BIG_ENDIAN or __LITTLE_ENDIAN must be defined!"
1649 #define INVALID_PORT_ID 0xFFFFFF
1652 * Switch info gathering structure.
1656 uint8_t node_name
[WWN_SIZE
];
1657 uint8_t port_name
[WWN_SIZE
];
1658 uint8_t fabric_port_name
[WWN_SIZE
];
1664 #define FC4_TYPE_FCP_SCSI 0x08
1665 #define FC4_TYPE_OTHER 0x0
1666 #define FC4_TYPE_UNKNOWN 0xff
1669 * Fibre channel port type.
1681 * Fibre channel port structure.
1683 typedef struct fc_port
{
1684 struct list_head list
;
1685 struct scsi_qla_host
*vha
;
1687 uint8_t node_name
[WWN_SIZE
];
1688 uint8_t port_name
[WWN_SIZE
];
1691 uint16_t old_loop_id
;
1695 uint8_t fabric_port_name
[WWN_SIZE
];
1698 fc_port_type_t port_type
;
1705 struct fc_rport
*rport
, *drport
;
1706 u32 supported_classes
;
1713 * Fibre channel port/lun states.
1715 #define FCS_UNCONFIGURED 1
1716 #define FCS_DEVICE_DEAD 2
1717 #define FCS_DEVICE_LOST 3
1718 #define FCS_ONLINE 4
1720 static const char * const port_state_str
[] = {
1731 #define FCF_FABRIC_DEVICE BIT_0
1732 #define FCF_LOGIN_NEEDED BIT_1
1733 #define FCF_FCP2_DEVICE BIT_2
1734 #define FCF_ASYNC_SENT BIT_3
1736 /* No loop ID flag. */
1737 #define FC_NO_LOOP_ID 0x1000
1742 * NOTE: All structures are big-endian in form.
1745 #define CT_REJECT_RESPONSE 0x8001
1746 #define CT_ACCEPT_RESPONSE 0x8002
1747 #define CT_REASON_INVALID_COMMAND_CODE 0x01
1748 #define CT_REASON_CANNOT_PERFORM 0x09
1749 #define CT_REASON_COMMAND_UNSUPPORTED 0x0b
1750 #define CT_EXPL_ALREADY_REGISTERED 0x10
1752 #define NS_N_PORT_TYPE 0x01
1753 #define NS_NL_PORT_TYPE 0x02
1754 #define NS_NX_PORT_TYPE 0x7F
1756 #define GA_NXT_CMD 0x100
1757 #define GA_NXT_REQ_SIZE (16 + 4)
1758 #define GA_NXT_RSP_SIZE (16 + 620)
1760 #define GID_PT_CMD 0x1A1
1761 #define GID_PT_REQ_SIZE (16 + 4)
1762 #define GID_PT_RSP_SIZE (16 + (MAX_FIBRE_DEVICES * 4))
1764 #define GPN_ID_CMD 0x112
1765 #define GPN_ID_REQ_SIZE (16 + 4)
1766 #define GPN_ID_RSP_SIZE (16 + 8)
1768 #define GNN_ID_CMD 0x113
1769 #define GNN_ID_REQ_SIZE (16 + 4)
1770 #define GNN_ID_RSP_SIZE (16 + 8)
1772 #define GFT_ID_CMD 0x117
1773 #define GFT_ID_REQ_SIZE (16 + 4)
1774 #define GFT_ID_RSP_SIZE (16 + 32)
1776 #define RFT_ID_CMD 0x217
1777 #define RFT_ID_REQ_SIZE (16 + 4 + 32)
1778 #define RFT_ID_RSP_SIZE 16
1780 #define RFF_ID_CMD 0x21F
1781 #define RFF_ID_REQ_SIZE (16 + 4 + 2 + 1 + 1)
1782 #define RFF_ID_RSP_SIZE 16
1784 #define RNN_ID_CMD 0x213
1785 #define RNN_ID_REQ_SIZE (16 + 4 + 8)
1786 #define RNN_ID_RSP_SIZE 16
1788 #define RSNN_NN_CMD 0x239
1789 #define RSNN_NN_REQ_SIZE (16 + 8 + 1 + 255)
1790 #define RSNN_NN_RSP_SIZE 16
1792 #define GFPN_ID_CMD 0x11C
1793 #define GFPN_ID_REQ_SIZE (16 + 4)
1794 #define GFPN_ID_RSP_SIZE (16 + 8)
1796 #define GPSC_CMD 0x127
1797 #define GPSC_REQ_SIZE (16 + 8)
1798 #define GPSC_RSP_SIZE (16 + 2 + 2)
1800 #define GFF_ID_CMD 0x011F
1801 #define GFF_ID_REQ_SIZE (16 + 4)
1802 #define GFF_ID_RSP_SIZE (16 + 128)
1805 * HBA attribute types.
1807 #define FDMI_HBA_ATTR_COUNT 9
1808 #define FDMI_HBA_NODE_NAME 1
1809 #define FDMI_HBA_MANUFACTURER 2
1810 #define FDMI_HBA_SERIAL_NUMBER 3
1811 #define FDMI_HBA_MODEL 4
1812 #define FDMI_HBA_MODEL_DESCRIPTION 5
1813 #define FDMI_HBA_HARDWARE_VERSION 6
1814 #define FDMI_HBA_DRIVER_VERSION 7
1815 #define FDMI_HBA_OPTION_ROM_VERSION 8
1816 #define FDMI_HBA_FIRMWARE_VERSION 9
1817 #define FDMI_HBA_OS_NAME_AND_VERSION 0xa
1818 #define FDMI_HBA_MAXIMUM_CT_PAYLOAD_LENGTH 0xb
1820 struct ct_fdmi_hba_attr
{
1824 uint8_t node_name
[WWN_SIZE
];
1825 uint8_t manufacturer
[32];
1826 uint8_t serial_num
[8];
1828 uint8_t model_desc
[80];
1829 uint8_t hw_version
[16];
1830 uint8_t driver_version
[32];
1831 uint8_t orom_version
[16];
1832 uint8_t fw_version
[16];
1833 uint8_t os_version
[128];
1834 uint8_t max_ct_len
[4];
1838 struct ct_fdmi_hba_attributes
{
1840 struct ct_fdmi_hba_attr entry
[FDMI_HBA_ATTR_COUNT
];
1844 * Port attribute types.
1846 #define FDMI_PORT_ATTR_COUNT 6
1847 #define FDMI_PORT_FC4_TYPES 1
1848 #define FDMI_PORT_SUPPORT_SPEED 2
1849 #define FDMI_PORT_CURRENT_SPEED 3
1850 #define FDMI_PORT_MAX_FRAME_SIZE 4
1851 #define FDMI_PORT_OS_DEVICE_NAME 5
1852 #define FDMI_PORT_HOST_NAME 6
1854 #define FDMI_PORT_SPEED_1GB 0x1
1855 #define FDMI_PORT_SPEED_2GB 0x2
1856 #define FDMI_PORT_SPEED_10GB 0x4
1857 #define FDMI_PORT_SPEED_4GB 0x8
1858 #define FDMI_PORT_SPEED_8GB 0x10
1859 #define FDMI_PORT_SPEED_16GB 0x20
1860 #define FDMI_PORT_SPEED_UNKNOWN 0x8000
1862 struct ct_fdmi_port_attr
{
1866 uint8_t fc4_types
[32];
1869 uint32_t max_frame_size
;
1870 uint8_t os_dev_name
[32];
1871 uint8_t host_name
[32];
1876 * Port Attribute Block.
1878 struct ct_fdmi_port_attributes
{
1880 struct ct_fdmi_port_attr entry
[FDMI_PORT_ATTR_COUNT
];
1883 /* FDMI definitions. */
1884 #define GRHL_CMD 0x100
1885 #define GHAT_CMD 0x101
1886 #define GRPL_CMD 0x102
1887 #define GPAT_CMD 0x110
1889 #define RHBA_CMD 0x200
1890 #define RHBA_RSP_SIZE 16
1892 #define RHAT_CMD 0x201
1893 #define RPRT_CMD 0x210
1895 #define RPA_CMD 0x211
1896 #define RPA_RSP_SIZE 16
1898 #define DHBA_CMD 0x300
1899 #define DHBA_REQ_SIZE (16 + 8)
1900 #define DHBA_RSP_SIZE 16
1902 #define DHAT_CMD 0x301
1903 #define DPRT_CMD 0x310
1904 #define DPA_CMD 0x311
1906 /* CT command header -- request/response common fields */
1916 /* CT command request */
1918 struct ct_cmd_hdr header
;
1920 uint16_t max_rsp_size
;
1921 uint8_t fragment_id
;
1922 uint8_t reserved
[3];
1925 /* GA_NXT, GPN_ID, GNN_ID, GFT_ID, GFPN_ID */
1941 uint8_t fc4_types
[32];
1948 uint8_t fc4_feature
;
1955 uint8_t node_name
[8];
1959 uint8_t node_name
[8];
1961 uint8_t sym_node_name
[255];
1965 uint8_t hba_indentifier
[8];
1969 uint8_t hba_identifier
[8];
1970 uint32_t entry_count
;
1971 uint8_t port_name
[8];
1972 struct ct_fdmi_hba_attributes attrs
;
1976 uint8_t hba_identifier
[8];
1977 struct ct_fdmi_hba_attributes attrs
;
1981 uint8_t port_name
[8];
1982 struct ct_fdmi_port_attributes attrs
;
1986 uint8_t port_name
[8];
1990 uint8_t port_name
[8];
1994 uint8_t port_name
[8];
1998 uint8_t port_name
[8];
2002 uint8_t port_name
[8];
2007 uint8_t port_name
[3];
2012 /* CT command response header */
2014 struct ct_cmd_hdr header
;
2017 uint8_t fragment_id
;
2018 uint8_t reason_code
;
2019 uint8_t explanation_code
;
2020 uint8_t vendor_unique
;
2023 struct ct_sns_gid_pt_data
{
2024 uint8_t control_byte
;
2029 struct ct_rsp_hdr header
;
2035 uint8_t port_name
[8];
2036 uint8_t sym_port_name_len
;
2037 uint8_t sym_port_name
[255];
2038 uint8_t node_name
[8];
2039 uint8_t sym_node_name_len
;
2040 uint8_t sym_node_name
[255];
2041 uint8_t init_proc_assoc
[8];
2042 uint8_t node_ip_addr
[16];
2043 uint8_t class_of_service
[4];
2044 uint8_t fc4_types
[32];
2045 uint8_t ip_address
[16];
2046 uint8_t fabric_port_name
[8];
2048 uint8_t hard_address
[3];
2052 struct ct_sns_gid_pt_data entries
[MAX_FIBRE_DEVICES
];
2056 uint8_t port_name
[8];
2060 uint8_t node_name
[8];
2064 uint8_t fc4_types
[32];
2068 uint32_t entry_count
;
2069 uint8_t port_name
[8];
2070 struct ct_fdmi_hba_attributes attrs
;
2074 uint8_t port_name
[8];
2082 #define GFF_FCP_SCSI_OFFSET 7
2084 uint8_t fc4_features
[128];
2091 struct ct_sns_req req
;
2092 struct ct_sns_rsp rsp
;
2097 * SNS command structures -- for 2200 compatibility.
2099 #define RFT_ID_SNS_SCMD_LEN 22
2100 #define RFT_ID_SNS_CMD_SIZE 60
2101 #define RFT_ID_SNS_DATA_SIZE 16
2103 #define RNN_ID_SNS_SCMD_LEN 10
2104 #define RNN_ID_SNS_CMD_SIZE 36
2105 #define RNN_ID_SNS_DATA_SIZE 16
2107 #define GA_NXT_SNS_SCMD_LEN 6
2108 #define GA_NXT_SNS_CMD_SIZE 28
2109 #define GA_NXT_SNS_DATA_SIZE (620 + 16)
2111 #define GID_PT_SNS_SCMD_LEN 6
2112 #define GID_PT_SNS_CMD_SIZE 28
2113 #define GID_PT_SNS_DATA_SIZE (MAX_FIBRE_DEVICES * 4 + 16)
2115 #define GPN_ID_SNS_SCMD_LEN 6
2116 #define GPN_ID_SNS_CMD_SIZE 28
2117 #define GPN_ID_SNS_DATA_SIZE (8 + 16)
2119 #define GNN_ID_SNS_SCMD_LEN 6
2120 #define GNN_ID_SNS_CMD_SIZE 28
2121 #define GNN_ID_SNS_DATA_SIZE (8 + 16)
2123 struct sns_cmd_pkt
{
2126 uint16_t buffer_length
;
2127 uint16_t reserved_1
;
2128 uint32_t buffer_address
[2];
2129 uint16_t subcommand_length
;
2130 uint16_t reserved_2
;
2131 uint16_t subcommand
;
2133 uint32_t reserved_3
;
2137 uint8_t rft_data
[RFT_ID_SNS_DATA_SIZE
];
2138 uint8_t rnn_data
[RNN_ID_SNS_DATA_SIZE
];
2139 uint8_t gan_data
[GA_NXT_SNS_DATA_SIZE
];
2140 uint8_t gid_data
[GID_PT_SNS_DATA_SIZE
];
2141 uint8_t gpn_data
[GPN_ID_SNS_DATA_SIZE
];
2142 uint8_t gnn_data
[GNN_ID_SNS_DATA_SIZE
];
2149 const struct firmware
*fw
;
2152 /* Return data from MBC_GET_ID_LIST call. */
2153 struct gid_list_info
{
2157 uint8_t loop_id_2100
; /* ISP2100/ISP2200 -- 4 bytes. */
2158 uint16_t loop_id
; /* ISP23XX -- 6 bytes. */
2159 uint16_t reserved_1
; /* ISP24XX -- 8 bytes. */
2161 #define GID_LIST_SIZE (sizeof(struct gid_list_info) * MAX_FIBRE_DEVICES)
2164 typedef struct vport_info
{
2165 uint8_t port_name
[WWN_SIZE
];
2166 uint8_t node_name
[WWN_SIZE
];
2169 unsigned long host_no
;
2174 typedef struct vport_params
{
2175 uint8_t port_name
[WWN_SIZE
];
2176 uint8_t node_name
[WWN_SIZE
];
2178 #define VP_OPTS_RETRY_ENABLE BIT_0
2179 #define VP_OPTS_VP_DISABLE BIT_1
2182 /* NPIV - return codes of VP create and modify */
2183 #define VP_RET_CODE_OK 0
2184 #define VP_RET_CODE_FATAL 1
2185 #define VP_RET_CODE_WRONG_ID 2
2186 #define VP_RET_CODE_WWPN 3
2187 #define VP_RET_CODE_RESOURCES 4
2188 #define VP_RET_CODE_NO_MEM 5
2189 #define VP_RET_CODE_NOT_FOUND 6
2196 struct isp_operations
{
2198 int (*pci_config
) (struct scsi_qla_host
*);
2199 void (*reset_chip
) (struct scsi_qla_host
*);
2200 int (*chip_diag
) (struct scsi_qla_host
*);
2201 void (*config_rings
) (struct scsi_qla_host
*);
2202 void (*reset_adapter
) (struct scsi_qla_host
*);
2203 int (*nvram_config
) (struct scsi_qla_host
*);
2204 void (*update_fw_options
) (struct scsi_qla_host
*);
2205 int (*load_risc
) (struct scsi_qla_host
*, uint32_t *);
2207 char * (*pci_info_str
) (struct scsi_qla_host
*, char *);
2208 char * (*fw_version_str
) (struct scsi_qla_host
*, char *);
2210 irq_handler_t intr_handler
;
2211 void (*enable_intrs
) (struct qla_hw_data
*);
2212 void (*disable_intrs
) (struct qla_hw_data
*);
2214 int (*abort_command
) (srb_t
*);
2215 int (*target_reset
) (struct fc_port
*, unsigned int, int);
2216 int (*lun_reset
) (struct fc_port
*, unsigned int, int);
2217 int (*fabric_login
) (struct scsi_qla_host
*, uint16_t, uint8_t,
2218 uint8_t, uint8_t, uint16_t *, uint8_t);
2219 int (*fabric_logout
) (struct scsi_qla_host
*, uint16_t, uint8_t,
2222 uint16_t (*calc_req_entries
) (uint16_t);
2223 void (*build_iocbs
) (srb_t
*, cmd_entry_t
*, uint16_t);
2224 void * (*prep_ms_iocb
) (struct scsi_qla_host
*, uint32_t, uint32_t);
2225 void * (*prep_ms_fdmi_iocb
) (struct scsi_qla_host
*, uint32_t,
2228 uint8_t * (*read_nvram
) (struct scsi_qla_host
*, uint8_t *,
2229 uint32_t, uint32_t);
2230 int (*write_nvram
) (struct scsi_qla_host
*, uint8_t *, uint32_t,
2233 void (*fw_dump
) (struct scsi_qla_host
*, int);
2235 int (*beacon_on
) (struct scsi_qla_host
*);
2236 int (*beacon_off
) (struct scsi_qla_host
*);
2237 void (*beacon_blink
) (struct scsi_qla_host
*);
2239 uint8_t * (*read_optrom
) (struct scsi_qla_host
*, uint8_t *,
2240 uint32_t, uint32_t);
2241 int (*write_optrom
) (struct scsi_qla_host
*, uint8_t *, uint32_t,
2244 int (*get_flash_version
) (struct scsi_qla_host
*, void *);
2245 int (*start_scsi
) (srb_t
*);
2246 int (*abort_isp
) (struct scsi_qla_host
*);
2249 /* MSI-X Support *************************************************************/
2251 #define QLA_MSIX_CHIP_REV_24XX 3
2252 #define QLA_MSIX_FW_MODE(m) (((m) & (BIT_7|BIT_8|BIT_9)) >> 7)
2253 #define QLA_MSIX_FW_MODE_1(m) (QLA_MSIX_FW_MODE(m) == 1)
2255 #define QLA_MSIX_DEFAULT 0x00
2256 #define QLA_MSIX_RSP_Q 0x01
2258 #define QLA_MIDX_DEFAULT 0
2259 #define QLA_MIDX_RSP_Q 1
2260 #define QLA_PCI_MSIX_CONTROL 0xa2
2262 struct scsi_qla_host
;
2264 struct qla_msix_entry
{
2268 struct rsp_que
*rsp
;
2271 #define WATCH_INTERVAL 1 /* number of seconds */
2274 enum qla_work_type
{
2277 QLA_EVT_ASYNC_LOGIN
,
2278 QLA_EVT_ASYNC_LOGIN_DONE
,
2279 QLA_EVT_ASYNC_LOGOUT
,
2280 QLA_EVT_ASYNC_LOGOUT_DONE
,
2281 QLA_EVT_ASYNC_ADISC
,
2282 QLA_EVT_ASYNC_ADISC_DONE
,
2287 struct qla_work_evt
{
2288 struct list_head list
;
2289 enum qla_work_type type
;
2291 #define QLA_EVT_FLAG_FREE 0x1
2295 enum fc_host_event_code code
;
2299 #define QLA_IDC_ACK_REGS 7
2300 uint16_t mb
[QLA_IDC_ACK_REGS
];
2303 struct fc_port
*fcport
;
2304 #define QLA_LOGIO_LOGIN_RETRIED BIT_0
2309 #define QLA_UEVENT_CODE_FW_DUMP 0
2314 struct qla_chip_state_84xx
{
2315 struct list_head list
;
2319 spinlock_t access_lock
;
2320 struct mutex fw_update_mutex
;
2322 uint32_t op_fw_version
;
2323 uint32_t op_fw_size
;
2324 uint32_t op_fw_seq_size
;
2325 uint32_t diag_fw_version
;
2326 uint32_t gold_fw_version
;
2329 struct qla_statistics
{
2330 uint32_t total_isp_aborts
;
2331 uint64_t input_bytes
;
2332 uint64_t output_bytes
;
2335 /* Multi queue support */
2336 #define MBC_INITIALIZE_MULTIQ 0x1f
2337 #define QLA_QUE_PAGE 0X1000
2338 #define QLA_MQ_SIZE 32
2339 #define QLA_MAX_QUEUES 256
2340 #define ISP_QUE_REG(ha, id) \
2342 ((void *)(ha->mqiobase) +\
2343 (QLA_QUE_PAGE * id)) :\
2344 ((void *)(ha->iobase)))
2345 #define QLA_REQ_QUE_ID(tag) \
2346 ((tag < QLA_MAX_QUEUES && tag > 0) ? tag : 0)
2347 #define QLA_DEFAULT_QUE_QOS 5
2348 #define QLA_PRECONFIG_VPORTS 32
2349 #define QLA_MAX_VPORTS_QLA24XX 128
2350 #define QLA_MAX_VPORTS_QLA25XX 256
2351 /* Response queue data structure */
2355 response_t
*ring_ptr
;
2356 uint32_t __iomem
*rsp_q_in
; /* FWI2-capable only. */
2357 uint32_t __iomem
*rsp_q_out
;
2358 uint16_t ring_index
;
2365 struct qla_hw_data
*hw
;
2366 struct qla_msix_entry
*msix
;
2367 struct req_que
*req
;
2368 srb_t
*status_srb
; /* status continuation entry */
2369 struct work_struct q_work
;
2372 /* Request queue data structure */
2376 request_t
*ring_ptr
;
2377 uint32_t __iomem
*req_q_in
; /* FWI2-capable only. */
2378 uint32_t __iomem
*req_q_out
;
2379 uint16_t ring_index
;
2388 struct rsp_que
*rsp
;
2389 srb_t
*outstanding_cmds
[MAX_OUTSTANDING_COMMANDS
];
2390 uint32_t current_outstanding_cmd
;
2394 /* Place holder for FW buffer parameters */
2402 * Qlogic host adapter specific data structure.
2404 struct qla_hw_data
{
2405 struct pci_dev
*pdev
;
2407 #define SRB_MIN_REQ 128
2408 mempool_t
*srb_mempool
;
2411 uint32_t mbox_int
:1;
2412 uint32_t mbox_busy
:1;
2413 uint32_t disable_risc_code_load
:1;
2414 uint32_t enable_64bit_addressing
:1;
2415 uint32_t enable_lip_reset
:1;
2416 uint32_t enable_target_reset
:1;
2417 uint32_t enable_lip_full_login
:1;
2418 uint32_t enable_led_scheme
:1;
2420 uint32_t msi_enabled
:1;
2421 uint32_t msix_enabled
:1;
2422 uint32_t disable_serdes
:1;
2423 uint32_t gpsc_supported
:1;
2424 uint32_t npiv_supported
:1;
2425 uint32_t pci_channel_io_perm_failure
:1;
2426 uint32_t fce_enabled
:1;
2427 uint32_t fac_supported
:1;
2429 uint32_t chip_reset_done
:1;
2431 uint32_t running_gold_fw
:1;
2432 uint32_t eeh_busy
:1;
2433 uint32_t cpu_affinity_enabled
:1;
2434 uint32_t disable_msix_handshake
:1;
2435 uint32_t fcp_prio_enabled
:1;
2436 uint32_t isp82xx_fw_hung
:1;
2438 uint32_t quiesce_owner
:1;
2439 uint32_t thermal_supported
:1;
2440 uint32_t isp82xx_reset_hdlr_active
:1;
2444 /* This spinlock is used to protect "io transactions", you must
2445 * acquire it before doing any IO to the card, eg with RD_REG*() and
2446 * WRT_REG*() for the duration of your entire commandtransaction.
2448 * This spinlock is of lower priority than the io request lock.
2451 spinlock_t hardware_lock ____cacheline_aligned
;
2454 device_reg_t __iomem
*iobase
; /* Base I/O address */
2455 resource_size_t pio_address
;
2457 #define MIN_IOBASE_LEN 0x100
2458 /* Multi queue data structs */
2459 device_reg_t __iomem
*mqiobase
;
2460 uint16_t msix_count
;
2462 struct req_que
**req_q_map
;
2463 struct rsp_que
**rsp_q_map
;
2464 unsigned long req_qid_map
[(QLA_MAX_QUEUES
/ 8) / sizeof(unsigned long)];
2465 unsigned long rsp_qid_map
[(QLA_MAX_QUEUES
/ 8) / sizeof(unsigned long)];
2466 uint8_t max_req_queues
;
2467 uint8_t max_rsp_queues
;
2468 struct qla_npiv_entry
*npiv_info
;
2469 uint16_t nvram_npiv_size
;
2471 uint16_t switch_cap
;
2472 #define FLOGI_SEQ_DEL BIT_8
2473 #define FLOGI_MID_SUPPORT BIT_10
2474 #define FLOGI_VSAN_SUPPORT BIT_12
2475 #define FLOGI_SP_SUPPORT BIT_13
2477 uint8_t port_no
; /* Physical port of adapter */
2479 /* Timeout timers. */
2480 uint8_t loop_down_abort_time
; /* port down timer */
2481 atomic_t loop_down_timer
; /* loop down timer */
2482 uint8_t link_down_timeout
; /* link down timeout */
2483 uint16_t max_loop_id
;
2486 uint16_t min_external_loopid
; /* First external loop Id */
2488 #define PORT_SPEED_UNKNOWN 0xFFFF
2489 #define PORT_SPEED_1GB 0x00
2490 #define PORT_SPEED_2GB 0x01
2491 #define PORT_SPEED_4GB 0x03
2492 #define PORT_SPEED_8GB 0x04
2493 #define PORT_SPEED_10GB 0x13
2494 uint16_t link_data_rate
; /* F/W operating speed */
2496 uint8_t current_topology
;
2497 uint8_t prev_topology
;
2498 #define ISP_CFG_NL 1
2500 #define ISP_CFG_FL 4
2503 uint8_t operating_mode
; /* F/W operating mode */
2508 uint8_t interrupts_on
;
2509 uint32_t isp_abort_cnt
;
2511 #define PCI_DEVICE_ID_QLOGIC_ISP2532 0x2532
2512 #define PCI_DEVICE_ID_QLOGIC_ISP8432 0x8432
2513 #define PCI_DEVICE_ID_QLOGIC_ISP8001 0x8001
2514 uint32_t device_type
;
2515 #define DT_ISP2100 BIT_0
2516 #define DT_ISP2200 BIT_1
2517 #define DT_ISP2300 BIT_2
2518 #define DT_ISP2312 BIT_3
2519 #define DT_ISP2322 BIT_4
2520 #define DT_ISP6312 BIT_5
2521 #define DT_ISP6322 BIT_6
2522 #define DT_ISP2422 BIT_7
2523 #define DT_ISP2432 BIT_8
2524 #define DT_ISP5422 BIT_9
2525 #define DT_ISP5432 BIT_10
2526 #define DT_ISP2532 BIT_11
2527 #define DT_ISP8432 BIT_12
2528 #define DT_ISP8001 BIT_13
2529 #define DT_ISP8021 BIT_14
2530 #define DT_ISP_LAST (DT_ISP8021 << 1)
2532 #define DT_IIDMA BIT_26
2533 #define DT_FWI2 BIT_27
2534 #define DT_ZIO_SUPPORTED BIT_28
2535 #define DT_OEM_001 BIT_29
2536 #define DT_ISP2200A BIT_30
2537 #define DT_EXTENDED_IDS BIT_31
2538 #define DT_MASK(ha) ((ha)->device_type & (DT_ISP_LAST - 1))
2539 #define IS_QLA2100(ha) (DT_MASK(ha) & DT_ISP2100)
2540 #define IS_QLA2200(ha) (DT_MASK(ha) & DT_ISP2200)
2541 #define IS_QLA2300(ha) (DT_MASK(ha) & DT_ISP2300)
2542 #define IS_QLA2312(ha) (DT_MASK(ha) & DT_ISP2312)
2543 #define IS_QLA2322(ha) (DT_MASK(ha) & DT_ISP2322)
2544 #define IS_QLA6312(ha) (DT_MASK(ha) & DT_ISP6312)
2545 #define IS_QLA6322(ha) (DT_MASK(ha) & DT_ISP6322)
2546 #define IS_QLA2422(ha) (DT_MASK(ha) & DT_ISP2422)
2547 #define IS_QLA2432(ha) (DT_MASK(ha) & DT_ISP2432)
2548 #define IS_QLA5422(ha) (DT_MASK(ha) & DT_ISP5422)
2549 #define IS_QLA5432(ha) (DT_MASK(ha) & DT_ISP5432)
2550 #define IS_QLA2532(ha) (DT_MASK(ha) & DT_ISP2532)
2551 #define IS_QLA8432(ha) (DT_MASK(ha) & DT_ISP8432)
2552 #define IS_QLA8001(ha) (DT_MASK(ha) & DT_ISP8001)
2553 #define IS_QLA82XX(ha) (DT_MASK(ha) & DT_ISP8021)
2555 #define IS_QLA23XX(ha) (IS_QLA2300(ha) || IS_QLA2312(ha) || IS_QLA2322(ha) || \
2556 IS_QLA6312(ha) || IS_QLA6322(ha))
2557 #define IS_QLA24XX(ha) (IS_QLA2422(ha) || IS_QLA2432(ha))
2558 #define IS_QLA54XX(ha) (IS_QLA5422(ha) || IS_QLA5432(ha))
2559 #define IS_QLA25XX(ha) (IS_QLA2532(ha))
2560 #define IS_QLA84XX(ha) (IS_QLA8432(ha))
2561 #define IS_QLA24XX_TYPE(ha) (IS_QLA24XX(ha) || IS_QLA54XX(ha) || \
2563 #define IS_QLA81XX(ha) (IS_QLA8001(ha))
2564 #define IS_QLA8XXX_TYPE(ha) (IS_QLA81XX(ha) || IS_QLA82XX(ha))
2565 #define IS_QLA2XXX_MIDTYPE(ha) (IS_QLA24XX(ha) || IS_QLA84XX(ha) || \
2566 IS_QLA25XX(ha) || IS_QLA81XX(ha) || \
2568 #define IS_MSIX_NACK_CAPABLE(ha) (IS_QLA81XX(ha))
2569 #define IS_NOPOLLING_TYPE(ha) ((IS_QLA25XX(ha) || IS_QLA81XX(ha)) && \
2570 (ha)->flags.msix_enabled)
2571 #define IS_FAC_REQUIRED(ha) (IS_QLA81XX(ha))
2572 #define IS_NOCACHE_VPD_TYPE(ha) (IS_QLA81XX(ha))
2573 #define IS_ALOGIO_CAPABLE(ha) (IS_QLA23XX(ha) || IS_FWI2_CAPABLE(ha))
2575 #define IS_IIDMA_CAPABLE(ha) ((ha)->device_type & DT_IIDMA)
2576 #define IS_FWI2_CAPABLE(ha) ((ha)->device_type & DT_FWI2)
2577 #define IS_ZIO_SUPPORTED(ha) ((ha)->device_type & DT_ZIO_SUPPORTED)
2578 #define IS_OEM_001(ha) ((ha)->device_type & DT_OEM_001)
2579 #define HAS_EXTENDED_IDS(ha) ((ha)->device_type & DT_EXTENDED_IDS)
2581 /* HBA serial number */
2586 /* NVRAM configuration data */
2587 #define MAX_NVRAM_SIZE 4096
2588 #define VPD_OFFSET MAX_NVRAM_SIZE / 2
2589 uint16_t nvram_size
;
2590 uint16_t nvram_base
;
2596 uint16_t loop_reset_delay
;
2597 uint8_t retry_count
;
2598 uint8_t login_timeout
;
2600 int port_down_retry_count
;
2603 uint32_t login_retry_count
;
2604 /* SNS command interfaces. */
2605 ms_iocb_entry_t
*ms_iocb
;
2606 dma_addr_t ms_iocb_dma
;
2607 struct ct_sns_pkt
*ct_sns
;
2608 dma_addr_t ct_sns_dma
;
2609 /* SNS command interfaces for 2200. */
2610 struct sns_cmd_pkt
*sns_cmd
;
2611 dma_addr_t sns_cmd_dma
;
2613 #define SFP_DEV_SIZE 256
2614 #define SFP_BLOCK_SIZE 64
2616 dma_addr_t sfp_data_dma
;
2619 dma_addr_t edc_data_dma
;
2620 uint16_t edc_data_len
;
2622 #define XGMAC_DATA_SIZE 4096
2624 dma_addr_t xgmac_data_dma
;
2626 #define DCBX_TLV_DATA_SIZE 4096
2628 dma_addr_t dcbx_tlv_dma
;
2630 struct task_struct
*dpc_thread
;
2631 uint8_t dpc_active
; /* DPC routine is active */
2633 dma_addr_t gid_list_dma
;
2634 struct gid_list_info
*gid_list
;
2635 int gid_list_info_size
;
2637 /* Small DMA pool allocations -- maximum 256 bytes in length. */
2638 #define DMA_POOL_SIZE 256
2639 struct dma_pool
*s_dma_pool
;
2641 dma_addr_t init_cb_dma
;
2644 dma_addr_t ex_init_cb_dma
;
2645 struct ex_init_cb_81xx
*ex_init_cb
;
2648 dma_addr_t async_pd_dma
;
2650 /* These are used by mailbox operations. */
2651 volatile uint16_t mailbox_out
[MAILBOX_REGISTER_COUNT
];
2654 unsigned long mbx_cmd_flags
;
2655 #define MBX_INTERRUPT 1
2656 #define MBX_INTR_WAIT 2
2657 #define MBX_UPDATE_FLASH_ACTIVE 3
2659 struct mutex vport_lock
; /* Virtual port synchronization */
2660 spinlock_t vport_slock
; /* order is hardware_lock, then vport_slock */
2661 struct completion mbx_cmd_comp
; /* Serialize mbx access */
2662 struct completion mbx_intr_comp
; /* Used for completion notification */
2663 struct completion dcbx_comp
; /* For set port config notification */
2664 int notify_dcbx_comp
;
2666 /* Basic firmware related information. */
2667 uint16_t fw_major_version
;
2668 uint16_t fw_minor_version
;
2669 uint16_t fw_subminor_version
;
2670 uint16_t fw_attributes
;
2671 uint32_t fw_memory_size
;
2672 uint32_t fw_transfer_size
;
2673 uint32_t fw_srisc_address
;
2674 #define RISC_START_ADDRESS_2100 0x1000
2675 #define RISC_START_ADDRESS_2300 0x800
2676 #define RISC_START_ADDRESS_2400 0x100000
2677 uint16_t fw_xcb_count
;
2679 uint16_t fw_options
[16]; /* slots: 1,2,3,10,11 */
2680 uint8_t fw_seriallink_options
[4];
2681 uint16_t fw_seriallink_options24
[4];
2683 uint8_t mpi_version
[3];
2684 uint32_t mpi_capabilities
;
2685 uint8_t phy_version
[3];
2687 /* Firmware dump information. */
2688 struct qla2xxx_fw_dump
*fw_dump
;
2689 uint32_t fw_dump_len
;
2691 int fw_dump_reading
;
2695 uint32_t chain_offset
;
2696 struct dentry
*dfs_dir
;
2697 struct dentry
*dfs_fce
;
2702 uint64_t fce_wr
, fce_rd
;
2703 struct mutex fce_mutex
;
2706 uint16_t chip_revision
;
2708 uint16_t product_id
[4];
2710 uint8_t model_number
[16+1];
2711 #define BINZERO "\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"
2712 char model_desc
[80];
2713 uint8_t adapter_id
[16+1];
2715 /* Option ROM information. */
2716 char *optrom_buffer
;
2717 uint32_t optrom_size
;
2719 #define QLA_SWAITING 0
2720 #define QLA_SREADING 1
2721 #define QLA_SWRITING 2
2722 uint32_t optrom_region_start
;
2723 uint32_t optrom_region_size
;
2725 /* PCI expansion ROM image information. */
2726 #define ROM_CODE_TYPE_BIOS 0
2727 #define ROM_CODE_TYPE_FCODE 1
2728 #define ROM_CODE_TYPE_EFI 3
2729 uint8_t bios_revision
[2];
2730 uint8_t efi_revision
[2];
2731 uint8_t fcode_revision
[16];
2732 uint32_t fw_revision
[4];
2734 uint32_t gold_fw_version
[4];
2736 /* Offsets for flash/nvram access (set to ~0 if not used). */
2737 uint32_t flash_conf_off
;
2738 uint32_t flash_data_off
;
2739 uint32_t nvram_conf_off
;
2740 uint32_t nvram_data_off
;
2742 uint32_t fdt_wrt_disable
;
2743 uint32_t fdt_erase_cmd
;
2744 uint32_t fdt_block_size
;
2745 uint32_t fdt_unprotect_sec_cmd
;
2746 uint32_t fdt_protect_sec_cmd
;
2748 uint32_t flt_region_flt
;
2749 uint32_t flt_region_fdt
;
2750 uint32_t flt_region_boot
;
2751 uint32_t flt_region_fw
;
2752 uint32_t flt_region_vpd_nvram
;
2753 uint32_t flt_region_vpd
;
2754 uint32_t flt_region_nvram
;
2755 uint32_t flt_region_npiv_conf
;
2756 uint32_t flt_region_gold_fw
;
2757 uint32_t flt_region_fcp_prio
;
2758 uint32_t flt_region_bootload
;
2760 /* Needed for BEACON */
2761 uint16_t beacon_blink_led
;
2762 uint8_t beacon_color_state
;
2763 #define QLA_LED_GRN_ON 0x01
2764 #define QLA_LED_YLW_ON 0x02
2765 #define QLA_LED_ABR_ON 0x04
2766 #define QLA_LED_ALL_ON 0x07 /* yellow, green, amber. */
2767 /* ISP2322: red, green, amber. */
2770 struct fc_host_statistics fc_host_stat
;
2772 struct qla_msix_entry
*msix_entries
;
2774 struct list_head vp_list
; /* list of VP */
2775 unsigned long vp_idx_map
[(MAX_MULTI_ID_FABRIC
/ 8) /
2776 sizeof(unsigned long)];
2777 uint16_t num_vhosts
; /* number of vports created */
2778 uint16_t num_vsans
; /* number of vsan created */
2779 uint16_t max_npiv_vports
; /* 63 or 125 per topoloty */
2780 int cur_vport_count
;
2782 struct qla_chip_state_84xx
*cs84xx
;
2783 struct qla_statistics qla_stats
;
2784 struct isp_operations
*isp_ops
;
2785 struct workqueue_struct
*wq
;
2786 struct qlfc_fw fw_buf
;
2788 /* FCP_CMND priority support */
2789 struct qla_fcp_prio_cfg
*fcp_prio_cfg
;
2791 struct dma_pool
*dl_dma_pool
;
2792 #define DSD_LIST_DMA_POOL_SIZE 512
2794 struct dma_pool
*fcp_cmnd_dma_pool
;
2795 mempool_t
*ctx_mempool
;
2796 #define FCP_CMND_DMA_POOL_SIZE 512
2798 unsigned long nx_pcibase
; /* Base I/O address */
2799 uint8_t *nxdb_rd_ptr
; /* Doorbell read pointer */
2800 unsigned long nxdb_wr_ptr
; /* Door bell write pointer */
2803 uint32_t curr_window
;
2804 uint32_t ddr_mn_window
;
2805 unsigned long mn_win_crb
;
2806 unsigned long ms_win_crb
;
2808 uint32_t nx_dev_init_timeout
;
2809 uint32_t nx_reset_timeout
;
2811 uint16_t portnum
; /* port number */
2813 struct fw_blob
*hablob
;
2814 struct qla82xx_legacy_intr_set nx_legacy_intr
;
2816 uint16_t gbl_dsd_inuse
;
2817 uint16_t gbl_dsd_avail
;
2818 struct list_head gbl_dsd_list
;
2819 #define NUM_DSD_CHAIN 4096
2822 __le32 file_prd_off
; /* File firmware product offset */
2826 * Qlogic scsi host structure
2828 typedef struct scsi_qla_host
{
2829 struct list_head list
;
2830 struct list_head vp_fcports
; /* list of fcports */
2831 struct list_head work_list
;
2832 spinlock_t work_lock
;
2834 /* Commonly used flags and state information. */
2835 struct Scsi_Host
*host
;
2836 unsigned long host_no
;
2837 uint8_t host_str
[16];
2840 uint32_t init_done
:1;
2842 uint32_t rscn_queue_overflow
:1;
2843 uint32_t reset_active
:1;
2845 uint32_t management_server_logged_in
:1;
2846 uint32_t process_response_queue
:1;
2847 uint32_t difdix_supported
:1;
2848 uint32_t delete_progress
:1;
2851 atomic_t loop_state
;
2852 #define LOOP_TIMEOUT 1
2855 #define LOOP_UPDATE 4
2856 #define LOOP_READY 5
2859 unsigned long dpc_flags
;
2860 #define RESET_MARKER_NEEDED 0 /* Send marker to ISP. */
2861 #define RESET_ACTIVE 1
2862 #define ISP_ABORT_NEEDED 2 /* Initiate ISP abort. */
2863 #define ABORT_ISP_ACTIVE 3 /* ISP abort in progress. */
2864 #define LOOP_RESYNC_NEEDED 4 /* Device Resync needed. */
2865 #define LOOP_RESYNC_ACTIVE 5
2866 #define LOCAL_LOOP_UPDATE 6 /* Perform a local loop update. */
2867 #define RSCN_UPDATE 7 /* Perform an RSCN update. */
2868 #define RELOGIN_NEEDED 8
2869 #define REGISTER_FC4_NEEDED 9 /* SNS FC4 registration required. */
2870 #define ISP_ABORT_RETRY 10 /* ISP aborted. */
2871 #define BEACON_BLINK_NEEDED 11
2872 #define REGISTER_FDMI_NEEDED 12
2873 #define FCPORT_UPDATE_NEEDED 13
2874 #define VP_DPC_NEEDED 14 /* wake up for VP dpc handling */
2875 #define UNLOADING 15
2876 #define NPIV_CONFIG_NEEDED 16
2877 #define ISP_UNRECOVERABLE 17
2878 #define FCOE_CTX_RESET_NEEDED 18 /* Initiate FCoE context reset */
2879 #define MPI_RESET_NEEDED 19 /* Initiate MPI FW reset */
2880 #define ISP_QUIESCE_NEEDED 20 /* Driver need some quiescence */
2882 uint32_t device_flags
;
2883 #define SWITCH_FOUND BIT_0
2884 #define DFLG_NO_CABLE BIT_1
2885 #define DFLG_DEV_FAILED BIT_5
2887 /* ISP configuration data. */
2888 uint16_t loop_id
; /* Host adapter loop id */
2890 port_id_t d_id
; /* Host adapter port id */
2891 uint8_t marker_needed
;
2892 uint16_t mgmt_svr_loop_id
;
2897 uint32_t rscn_queue
[MAX_RSCN_COUNT
];
2898 uint8_t rscn_in_ptr
;
2899 uint8_t rscn_out_ptr
;
2901 /* Timeout timers. */
2902 uint8_t loop_down_abort_time
; /* port down timer */
2903 atomic_t loop_down_timer
; /* loop down timer */
2904 uint8_t link_down_timeout
; /* link down timeout */
2906 uint32_t timer_active
;
2907 struct timer_list timer
;
2909 uint8_t node_name
[WWN_SIZE
];
2910 uint8_t port_name
[WWN_SIZE
];
2911 uint8_t fabric_node_name
[WWN_SIZE
];
2913 uint16_t fcoe_vlan_id
;
2914 uint16_t fcoe_fcf_idx
;
2915 uint8_t fcoe_vn_port_mac
[6];
2917 uint32_t vp_abort_cnt
;
2919 struct fc_vport
*fc_vport
; /* holds fc_vport * for each vport */
2920 uint16_t vp_idx
; /* vport ID */
2922 unsigned long vp_flags
;
2923 #define VP_IDX_ACQUIRED 0 /* bit no 0 */
2924 #define VP_CREATE_NEEDED 1
2925 #define VP_BIND_NEEDED 2
2926 #define VP_DELETE_NEEDED 3
2927 #define VP_SCR_NEEDED 4 /* State Change Request registration */
2929 #define VP_OFFLINE 0
2932 // #define VP_DISABLE 3
2933 uint16_t vp_err_state
;
2934 uint16_t vp_prev_err_state
;
2935 #define VP_ERR_UNKWN 0
2936 #define VP_ERR_PORTDWN 1
2937 #define VP_ERR_FAB_UNSUPPORTED 2
2938 #define VP_ERR_FAB_NORESOURCES 3
2939 #define VP_ERR_FAB_LOGOUT 4
2940 #define VP_ERR_ADAP_NORESOURCES 5
2941 struct qla_hw_data
*hw
;
2942 struct req_que
*req
;
2943 int fw_heartbeat_counter
;
2944 int seconds_since_last_heartbeat
;
2946 atomic_t vref_count
;
2950 * Macros to help code, maintain, etc.
2952 #define LOOP_TRANSITION(ha) \
2953 (test_bit(ISP_ABORT_NEEDED, &ha->dpc_flags) || \
2954 test_bit(LOOP_RESYNC_NEEDED, &ha->dpc_flags) || \
2955 atomic_read(&ha->loop_state) == LOOP_DOWN)
2957 #define QLA_VHA_MARK_BUSY(__vha, __bail) do { \
2958 atomic_inc(&__vha->vref_count); \
2960 if (__vha->flags.delete_progress) { \
2961 atomic_dec(&__vha->vref_count); \
2968 #define QLA_VHA_MARK_NOT_BUSY(__vha) do { \
2969 atomic_dec(&__vha->vref_count); \
2973 #define qla_printk(level, ha, format, arg...) \
2974 dev_printk(level , &((ha)->pdev->dev) , format , ## arg)
2977 * qla2x00 local function return status codes
2979 #define MBS_MASK 0x3fff
2981 #define QLA_SUCCESS (MBS_COMMAND_COMPLETE & MBS_MASK)
2982 #define QLA_INVALID_COMMAND (MBS_INVALID_COMMAND & MBS_MASK)
2983 #define QLA_INTERFACE_ERROR (MBS_HOST_INTERFACE_ERROR & MBS_MASK)
2984 #define QLA_TEST_FAILED (MBS_TEST_FAILED & MBS_MASK)
2985 #define QLA_COMMAND_ERROR (MBS_COMMAND_ERROR & MBS_MASK)
2986 #define QLA_PARAMETER_ERROR (MBS_COMMAND_PARAMETER_ERROR & MBS_MASK)
2987 #define QLA_PORT_ID_USED (MBS_PORT_ID_USED & MBS_MASK)
2988 #define QLA_LOOP_ID_USED (MBS_LOOP_ID_USED & MBS_MASK)
2989 #define QLA_ALL_IDS_IN_USE (MBS_ALL_IDS_IN_USE & MBS_MASK)
2990 #define QLA_NOT_LOGGED_IN (MBS_NOT_LOGGED_IN & MBS_MASK)
2992 #define QLA_FUNCTION_TIMEOUT 0x100
2993 #define QLA_FUNCTION_PARAMETER_ERROR 0x101
2994 #define QLA_FUNCTION_FAILED 0x102
2995 #define QLA_MEMORY_ALLOC_FAILED 0x103
2996 #define QLA_LOCK_TIMEOUT 0x104
2997 #define QLA_ABORTED 0x105
2998 #define QLA_SUSPENDED 0x106
2999 #define QLA_BUSY 0x107
3000 #define QLA_RSCNS_HANDLED 0x108
3001 #define QLA_ALREADY_REGISTERED 0x109
3003 #define NVRAM_DELAY() udelay(10)
3005 #define INVALID_HANDLE (MAX_OUTSTANDING_COMMANDS+1)
3008 * Flash support definitions
3010 #define OPTROM_SIZE_2300 0x20000
3011 #define OPTROM_SIZE_2322 0x100000
3012 #define OPTROM_SIZE_24XX 0x100000
3013 #define OPTROM_SIZE_25XX 0x200000
3014 #define OPTROM_SIZE_81XX 0x400000
3015 #define OPTROM_SIZE_82XX 0x800000
3017 #define OPTROM_BURST_SIZE 0x1000
3018 #define OPTROM_BURST_DWORDS (OPTROM_BURST_SIZE / 4)
3020 #define QLA_DSDS_PER_IOCB 37
3022 #define CMD_SP(Cmnd) ((Cmnd)->SCp.ptr)
3024 #define QLA_SG_ALL 1024
3026 enum nexus_wait_type
{
3032 #include "qla_gbl.h"
3033 #include "qla_dbg.h"
3034 #include "qla_inline.h"