arch/powerpc/platforms/52xx/lite5200.c

   1 /*
   2  * Freescale Lite5200 board support
   3  *
   4  * Written by: Grant Likely <grant.likely@secretlab.ca>
   5  *
   6  * Copyright (C) Secret Lab Technologies Ltd. 2006. All rights reserved.
   7  * Copyright (C) Freescale Semicondutor, Inc. 2006. All rights reserved.
   8  *
   9  * Description:
  10  * This program is free software; you can redistribute  it and/or modify it
  11  * under  the terms of  the GNU General  Public License as published by the
  12  * Free Software Foundation;  either version 2 of the  License, or (at your
  13  * option) any later version.
  14  */
  15
  16 #undef DEBUG
  17
  18 #include <linux/init.h>
  19 #include <linux/pci.h>
  20 #include <linux/of.h>
  21 #include <linux/of_address.h>
  22 #include <linux/root_dev.h>
  23 #include <linux/initrd.h>
  24 #include <asm/time.h>
  25 #include <asm/io.h>
  26 #include <asm/machdep.h>
  27 #include <asm/prom.h>
  28 #include <asm/mpc52xx.h>
  29
  30 /* ************************************************************************
  31  *
  32  * Setup the architecture
  33  *
  34  */
  35
  36 /* mpc5200 device tree match tables */
  37 static struct of_device_id mpc5200_cdm_ids[] __initdata = {
  38         { .compatible = "fsl,mpc5200-cdm", },
  39         { .compatible = "mpc5200-cdm", },
  40         {}
  41 };
  42
  43 static struct of_device_id mpc5200_gpio_ids[] __initdata = {
  44         { .compatible = "fsl,mpc5200-gpio", },
  45         { .compatible = "mpc5200-gpio", },
  46         {}
  47 };
  48
  49 /*
  50  * Fix clock configuration.
  51  *
  52  * Firmware is supposed to be responsible for this.  If you are creating a
  53  * new board port, do *NOT* duplicate this code.  Fix your boot firmware
  54  * to set it correctly in the first place
  55  */
  56 static void __init
  57 lite5200_fix_clock_config(void)
  58 {
  59         struct device_node *np;
  60         struct mpc52xx_cdm  __iomem *cdm;
  61         /* Map zones */
  62         np = of_find_matching_node(NULL, mpc5200_cdm_ids);
  63         cdm = of_iomap(np, 0);
  64         of_node_put(np);
  65         if (!cdm) {
  66                 printk(KERN_ERR "%s() failed; expect abnormal behaviour\n",
  67                        __func__);
  68                 return;
  69         }
  70
  71         /* Use internal 48 Mhz */
  72         out_8(&cdm->ext_48mhz_en, 0x00);
  73         out_8(&cdm->fd_enable, 0x01);
  74         if (in_be32(&cdm->rstcfg) & 0x40)       /* Assumes 33Mhz clock */
  75                 out_be16(&cdm->fd_counters, 0x0001);
  76         else
  77                 out_be16(&cdm->fd_counters, 0x5555);
  78
  79         /* Unmap the regs */
  80         iounmap(cdm);
  81 }
  82
  83 /*
  84  * Fix setting of port_config register.
  85  *
  86  * Firmware is supposed to be responsible for this.  If you are creating a
  87  * new board port, do *NOT* duplicate this code.  Fix your boot firmware
  88  * to set it correctly in the first place
  89  */
  90 static void __init
  91 lite5200_fix_port_config(void)
  92 {
  93         struct device_node *np;
  94         struct mpc52xx_gpio __iomem *gpio;
  95         u32 port_config;
  96
  97         np = of_find_matching_node(NULL, mpc5200_gpio_ids);
  98         gpio = of_iomap(np, 0);
  99         of_node_put(np);
 100         if (!gpio) {
 101                 printk(KERN_ERR "%s() failed. expect abnormal behavior\n",
 102                        __func__);
 103                 return;
 104         }
 105
 106         /* Set port config */
 107         port_config = in_be32(&gpio->port_config);
 108
 109         port_config &= ~0x00800000;     /* 48Mhz internal, pin is GPIO  */
 110
 111         port_config &= ~0x00007000;     /* USB port : Differential mode */
 112         port_config |=  0x00001000;     /*            USB 1 only        */
 113
 114         port_config &= ~0x03000000;     /* ATA CS is on csb_4/5         */
 115         port_config |=  0x01000000;
 116
 117         pr_debug("port_config: old:%x new:%x\n",
 118                  in_be32(&gpio->port_config), port_config);
 119         out_be32(&gpio->port_config, port_config);
 120
 121         /* Unmap zone */
 122         iounmap(gpio);
 123 }
 124
 125 #ifdef CONFIG_PM
 126 static void lite5200_suspend_prepare(void __iomem *mbar)
 127 {
 128         u8 pin = 1;     /* GPIO_WKUP_1 (GPIO_PSC2_4) */
 129         u8 level = 0;   /* wakeup on low level */
 130         mpc52xx_set_wakeup_gpio(pin, level);
 131
 132         /*
 133          * power down usb port
 134          * this needs to be called before of-ohci suspend code
 135          */
 136
 137         /* set ports to "power switched" and "powered at the same time"
 138          * USB Rh descriptor A: NPS = 0, PSM = 0 */
 139         out_be32(mbar + 0x1048, in_be32(mbar + 0x1048) & ~0x300);
 140         /* USB Rh status: LPS = 1 - turn off power */
 141         out_be32(mbar + 0x1050, 0x00000001);
 142 }
 143
 144 static void lite5200_resume_finish(void __iomem *mbar)
 145 {
 146         /* USB Rh status: LPSC = 1 - turn on power */
 147         out_be32(mbar + 0x1050, 0x00010000);
 148 }
 149 #endif
 150
 151 static void __init lite5200_setup_arch(void)
 152 {
 153         if (ppc_md.progress)
 154                 ppc_md.progress("lite5200_setup_arch()", 0);
 155
 156         /* Map important registers from the internal memory map */
 157         mpc52xx_map_common_devices();
 158
 159         /* Some mpc5200 & mpc5200b related configuration */
 160         mpc5200_setup_xlb_arbiter();
 161
 162         /* Fix things that firmware should have done. */
 163         lite5200_fix_clock_config();
 164         lite5200_fix_port_config();
 165
 166 #ifdef CONFIG_PM
 167         mpc52xx_suspend.board_suspend_prepare = lite5200_suspend_prepare;
 168         mpc52xx_suspend.board_resume_finish = lite5200_resume_finish;
 169         lite5200_pm_init();
 170 #endif
 171
 172         mpc52xx_setup_pci();
 173 }
 174
 175 static const char *board[] __initdata = {
 176         "fsl,lite5200",
 177         "fsl,lite5200b",
 178         NULL,
 179 };
 180
 181 /*
 182  * Called very early, MMU is off, device-tree isn't unflattened
 183  */
 184 static int __init lite5200_probe(void)
 185 {
 186         return of_flat_dt_match(of_get_flat_dt_root(), board);
 187 }
 188
 189 define_machine(lite5200) {
 190         .name           = "lite5200",
 191         .probe          = lite5200_probe,
 192         .setup_arch     = lite5200_setup_arch,
 193         .init           = mpc52xx_declare_of_platform_devices,
 194         .init_IRQ       = mpc52xx_init_irq,
 195         .get_irq        = mpc52xx_get_irq,
 196         .restart        = mpc52xx_restart,
 197         .calibrate_decr = generic_calibrate_decr,
 198 };