2 * Freescale USB device/endpoint management registers
4 #ifndef __FSL_USB2_UDC_H
5 #define __FSL_USB2_UDC_H
7 /* ### define USB registers here
9 #define USB_MAX_CTRL_PAYLOAD 64
10 #define USB_DR_SYS_OFFSET 0x400
12 /* USB DR device mode registers (Little Endian) */
13 struct usb_dr_device
{
14 /* Capability register */
16 u16 caplength
; /* Capability Register Length */
17 u16 hciversion
; /* Host Controller Interface Version */
18 u32 hcsparams
; /* Host Controller Structural Parameters */
19 u32 hccparams
; /* Host Controller Capability Parameters */
21 u32 dciversion
; /* Device Controller Interface Version */
22 u32 dccparams
; /* Device Controller Capability Parameters */
24 /* Operation register */
25 u32 usbcmd
; /* USB Command Register */
26 u32 usbsts
; /* USB Status Register */
27 u32 usbintr
; /* USB Interrupt Enable Register */
28 u32 frindex
; /* Frame Index Register */
30 u32 deviceaddr
; /* Device Address */
31 u32 endpointlistaddr
; /* Endpoint List Address Register */
33 u32 burstsize
; /* Master Interface Data Burst Size Register */
34 u32 txttfilltuning
; /* Transmit FIFO Tuning Controls Register */
36 u32 configflag
; /* Configure Flag Register */
37 u32 portsc1
; /* Port 1 Status and Control Register */
39 u32 otgsc
; /* On-The-Go Status and Control */
40 u32 usbmode
; /* USB Mode Register */
41 u32 endptsetupstat
; /* Endpoint Setup Status Register */
42 u32 endpointprime
; /* Endpoint Initialization Register */
43 u32 endptflush
; /* Endpoint Flush Register */
44 u32 endptstatus
; /* Endpoint Status Register */
45 u32 endptcomplete
; /* Endpoint Complete Register */
46 u32 endptctrl
[6]; /* Endpoint Control Registers */
49 /* USB DR host mode registers (Little Endian) */
51 /* Capability register */
53 u16 caplength
; /* Capability Register Length */
54 u16 hciversion
; /* Host Controller Interface Version */
55 u32 hcsparams
; /* Host Controller Structural Parameters */
56 u32 hccparams
; /* Host Controller Capability Parameters */
58 u32 dciversion
; /* Device Controller Interface Version */
59 u32 dccparams
; /* Device Controller Capability Parameters */
61 /* Operation register */
62 u32 usbcmd
; /* USB Command Register */
63 u32 usbsts
; /* USB Status Register */
64 u32 usbintr
; /* USB Interrupt Enable Register */
65 u32 frindex
; /* Frame Index Register */
67 u32 periodiclistbase
; /* Periodic Frame List Base Address Register */
68 u32 asynclistaddr
; /* Current Asynchronous List Address Register */
70 u32 burstsize
; /* Master Interface Data Burst Size Register */
71 u32 txttfilltuning
; /* Transmit FIFO Tuning Controls Register */
73 u32 configflag
; /* Configure Flag Register */
74 u32 portsc1
; /* Port 1 Status and Control Register */
76 u32 otgsc
; /* On-The-Go Status and Control */
77 u32 usbmode
; /* USB Mode Register */
78 u32 endptsetupstat
; /* Endpoint Setup Status Register */
79 u32 endpointprime
; /* Endpoint Initialization Register */
80 u32 endptflush
; /* Endpoint Flush Register */
81 u32 endptstatus
; /* Endpoint Status Register */
82 u32 endptcomplete
; /* Endpoint Complete Register */
83 u32 endptctrl
[6]; /* Endpoint Control Registers */
86 /* non-EHCI USB system interface registers (Big Endian) */
87 struct usb_sys_interface
{
90 u32 age_cnt_thresh
; /* Age Count Threshold Register */
91 u32 pri_ctrl
; /* Priority Control Register */
92 u32 si_ctrl
; /* System Interface Control Register */
94 u32 control
; /* General Purpose Control Register */
97 /* ep0 transfer state */
98 #define WAIT_FOR_SETUP 0
99 #define DATA_STATE_XMIT 1
100 #define DATA_STATE_NEED_ZLP 2
101 #define WAIT_FOR_OUT_STATUS 3
102 #define DATA_STATE_RECV 4
104 /* Device Controller Capability Parameter register */
105 #define DCCPARAMS_DC 0x00000080
106 #define DCCPARAMS_DEN_MASK 0x0000001f
108 /* Frame Index Register Bit Masks */
109 #define USB_FRINDEX_MASKS 0x3fff
110 /* USB CMD Register Bit Masks */
111 #define USB_CMD_RUN_STOP 0x00000001
112 #define USB_CMD_CTRL_RESET 0x00000002
113 #define USB_CMD_PERIODIC_SCHEDULE_EN 0x00000010
114 #define USB_CMD_ASYNC_SCHEDULE_EN 0x00000020
115 #define USB_CMD_INT_AA_DOORBELL 0x00000040
116 #define USB_CMD_ASP 0x00000300
117 #define USB_CMD_ASYNC_SCH_PARK_EN 0x00000800
118 #define USB_CMD_SUTW 0x00002000
119 #define USB_CMD_ATDTW 0x00004000
120 #define USB_CMD_ITC 0x00FF0000
122 /* bit 15,3,2 are frame list size */
123 #define USB_CMD_FRAME_SIZE_1024 0x00000000
124 #define USB_CMD_FRAME_SIZE_512 0x00000004
125 #define USB_CMD_FRAME_SIZE_256 0x00000008
126 #define USB_CMD_FRAME_SIZE_128 0x0000000C
127 #define USB_CMD_FRAME_SIZE_64 0x00008000
128 #define USB_CMD_FRAME_SIZE_32 0x00008004
129 #define USB_CMD_FRAME_SIZE_16 0x00008008
130 #define USB_CMD_FRAME_SIZE_8 0x0000800C
132 /* bit 9-8 are async schedule park mode count */
133 #define USB_CMD_ASP_00 0x00000000
134 #define USB_CMD_ASP_01 0x00000100
135 #define USB_CMD_ASP_10 0x00000200
136 #define USB_CMD_ASP_11 0x00000300
137 #define USB_CMD_ASP_BIT_POS 8
139 /* bit 23-16 are interrupt threshold control */
140 #define USB_CMD_ITC_NO_THRESHOLD 0x00000000
141 #define USB_CMD_ITC_1_MICRO_FRM 0x00010000
142 #define USB_CMD_ITC_2_MICRO_FRM 0x00020000
143 #define USB_CMD_ITC_4_MICRO_FRM 0x00040000
144 #define USB_CMD_ITC_8_MICRO_FRM 0x00080000
145 #define USB_CMD_ITC_16_MICRO_FRM 0x00100000
146 #define USB_CMD_ITC_32_MICRO_FRM 0x00200000
147 #define USB_CMD_ITC_64_MICRO_FRM 0x00400000
148 #define USB_CMD_ITC_BIT_POS 16
150 /* USB STS Register Bit Masks */
151 #define USB_STS_INT 0x00000001
152 #define USB_STS_ERR 0x00000002
153 #define USB_STS_PORT_CHANGE 0x00000004
154 #define USB_STS_FRM_LST_ROLL 0x00000008
155 #define USB_STS_SYS_ERR 0x00000010
156 #define USB_STS_IAA 0x00000020
157 #define USB_STS_RESET 0x00000040
158 #define USB_STS_SOF 0x00000080
159 #define USB_STS_SUSPEND 0x00000100
160 #define USB_STS_HC_HALTED 0x00001000
161 #define USB_STS_RCL 0x00002000
162 #define USB_STS_PERIODIC_SCHEDULE 0x00004000
163 #define USB_STS_ASYNC_SCHEDULE 0x00008000
165 /* USB INTR Register Bit Masks */
166 #define USB_INTR_INT_EN 0x00000001
167 #define USB_INTR_ERR_INT_EN 0x00000002
168 #define USB_INTR_PTC_DETECT_EN 0x00000004
169 #define USB_INTR_FRM_LST_ROLL_EN 0x00000008
170 #define USB_INTR_SYS_ERR_EN 0x00000010
171 #define USB_INTR_ASYN_ADV_EN 0x00000020
172 #define USB_INTR_RESET_EN 0x00000040
173 #define USB_INTR_SOF_EN 0x00000080
174 #define USB_INTR_DEVICE_SUSPEND 0x00000100
176 /* Device Address bit masks */
177 #define USB_DEVICE_ADDRESS_MASK 0xFE000000
178 #define USB_DEVICE_ADDRESS_BIT_POS 25
180 /* endpoint list address bit masks */
181 #define USB_EP_LIST_ADDRESS_MASK 0xfffff800
183 /* PORTSCX Register Bit Masks */
184 #define PORTSCX_CURRENT_CONNECT_STATUS 0x00000001
185 #define PORTSCX_CONNECT_STATUS_CHANGE 0x00000002
186 #define PORTSCX_PORT_ENABLE 0x00000004
187 #define PORTSCX_PORT_EN_DIS_CHANGE 0x00000008
188 #define PORTSCX_OVER_CURRENT_ACT 0x00000010
189 #define PORTSCX_OVER_CURRENT_CHG 0x00000020
190 #define PORTSCX_PORT_FORCE_RESUME 0x00000040
191 #define PORTSCX_PORT_SUSPEND 0x00000080
192 #define PORTSCX_PORT_RESET 0x00000100
193 #define PORTSCX_LINE_STATUS_BITS 0x00000C00
194 #define PORTSCX_PORT_POWER 0x00001000
195 #define PORTSCX_PORT_INDICTOR_CTRL 0x0000C000
196 #define PORTSCX_PORT_TEST_CTRL 0x000F0000
197 #define PORTSCX_WAKE_ON_CONNECT_EN 0x00100000
198 #define PORTSCX_WAKE_ON_CONNECT_DIS 0x00200000
199 #define PORTSCX_WAKE_ON_OVER_CURRENT 0x00400000
200 #define PORTSCX_PHY_LOW_POWER_SPD 0x00800000
201 #define PORTSCX_PORT_FORCE_FULL_SPEED 0x01000000
202 #define PORTSCX_PORT_SPEED_MASK 0x0C000000
203 #define PORTSCX_PORT_WIDTH 0x10000000
204 #define PORTSCX_PHY_TYPE_SEL 0xC0000000
206 /* bit 11-10 are line status */
207 #define PORTSCX_LINE_STATUS_SE0 0x00000000
208 #define PORTSCX_LINE_STATUS_JSTATE 0x00000400
209 #define PORTSCX_LINE_STATUS_KSTATE 0x00000800
210 #define PORTSCX_LINE_STATUS_UNDEF 0x00000C00
211 #define PORTSCX_LINE_STATUS_BIT_POS 10
213 /* bit 15-14 are port indicator control */
214 #define PORTSCX_PIC_OFF 0x00000000
215 #define PORTSCX_PIC_AMBER 0x00004000
216 #define PORTSCX_PIC_GREEN 0x00008000
217 #define PORTSCX_PIC_UNDEF 0x0000C000
218 #define PORTSCX_PIC_BIT_POS 14
220 /* bit 19-16 are port test control */
221 #define PORTSCX_PTC_DISABLE 0x00000000
222 #define PORTSCX_PTC_JSTATE 0x00010000
223 #define PORTSCX_PTC_KSTATE 0x00020000
224 #define PORTSCX_PTC_SEQNAK 0x00030000
225 #define PORTSCX_PTC_PACKET 0x00040000
226 #define PORTSCX_PTC_FORCE_EN 0x00050000
227 #define PORTSCX_PTC_BIT_POS 16
229 /* bit 27-26 are port speed */
230 #define PORTSCX_PORT_SPEED_FULL 0x00000000
231 #define PORTSCX_PORT_SPEED_LOW 0x04000000
232 #define PORTSCX_PORT_SPEED_HIGH 0x08000000
233 #define PORTSCX_PORT_SPEED_UNDEF 0x0C000000
234 #define PORTSCX_SPEED_BIT_POS 26
236 /* bit 28 is parallel transceiver width for UTMI interface */
237 #define PORTSCX_PTW 0x10000000
238 #define PORTSCX_PTW_8BIT 0x00000000
239 #define PORTSCX_PTW_16BIT 0x10000000
241 /* bit 31-30 are port transceiver select */
242 #define PORTSCX_PTS_UTMI 0x00000000
243 #define PORTSCX_PTS_ULPI 0x80000000
244 #define PORTSCX_PTS_FSLS 0xC0000000
245 #define PORTSCX_PTS_BIT_POS 30
247 /* otgsc Register Bit Masks */
248 #define OTGSC_CTRL_VUSB_DISCHARGE 0x00000001
249 #define OTGSC_CTRL_VUSB_CHARGE 0x00000002
250 #define OTGSC_CTRL_OTG_TERM 0x00000008
251 #define OTGSC_CTRL_DATA_PULSING 0x00000010
252 #define OTGSC_STS_USB_ID 0x00000100
253 #define OTGSC_STS_A_VBUS_VALID 0x00000200
254 #define OTGSC_STS_A_SESSION_VALID 0x00000400
255 #define OTGSC_STS_B_SESSION_VALID 0x00000800
256 #define OTGSC_STS_B_SESSION_END 0x00001000
257 #define OTGSC_STS_1MS_TOGGLE 0x00002000
258 #define OTGSC_STS_DATA_PULSING 0x00004000
259 #define OTGSC_INTSTS_USB_ID 0x00010000
260 #define OTGSC_INTSTS_A_VBUS_VALID 0x00020000
261 #define OTGSC_INTSTS_A_SESSION_VALID 0x00040000
262 #define OTGSC_INTSTS_B_SESSION_VALID 0x00080000
263 #define OTGSC_INTSTS_B_SESSION_END 0x00100000
264 #define OTGSC_INTSTS_1MS 0x00200000
265 #define OTGSC_INTSTS_DATA_PULSING 0x00400000
266 #define OTGSC_INTR_USB_ID 0x01000000
267 #define OTGSC_INTR_A_VBUS_VALID 0x02000000
268 #define OTGSC_INTR_A_SESSION_VALID 0x04000000
269 #define OTGSC_INTR_B_SESSION_VALID 0x08000000
270 #define OTGSC_INTR_B_SESSION_END 0x10000000
271 #define OTGSC_INTR_1MS_TIMER 0x20000000
272 #define OTGSC_INTR_DATA_PULSING 0x40000000
274 /* USB MODE Register Bit Masks */
275 #define USB_MODE_CTRL_MODE_IDLE 0x00000000
276 #define USB_MODE_CTRL_MODE_DEVICE 0x00000002
277 #define USB_MODE_CTRL_MODE_HOST 0x00000003
278 #define USB_MODE_CTRL_MODE_MASK 0x00000003
279 #define USB_MODE_CTRL_MODE_RSV 0x00000001
280 #define USB_MODE_ES 0x00000004 /* Endian Select */
281 #define USB_MODE_SETUP_LOCK_OFF 0x00000008
282 #define USB_MODE_STREAM_DISABLE 0x00000010
283 /* Endpoint Flush Register */
284 #define EPFLUSH_TX_OFFSET 0x00010000
285 #define EPFLUSH_RX_OFFSET 0x00000000
287 /* Endpoint Setup Status bit masks */
288 #define EP_SETUP_STATUS_MASK 0x0000003F
289 #define EP_SETUP_STATUS_EP0 0x00000001
291 /* ENDPOINTCTRLx Register Bit Masks */
292 #define EPCTRL_TX_ENABLE 0x00800000
293 #define EPCTRL_TX_DATA_TOGGLE_RST 0x00400000 /* Not EP0 */
294 #define EPCTRL_TX_DATA_TOGGLE_INH 0x00200000 /* Not EP0 */
295 #define EPCTRL_TX_TYPE 0x000C0000
296 #define EPCTRL_TX_DATA_SOURCE 0x00020000 /* Not EP0 */
297 #define EPCTRL_TX_EP_STALL 0x00010000
298 #define EPCTRL_RX_ENABLE 0x00000080
299 #define EPCTRL_RX_DATA_TOGGLE_RST 0x00000040 /* Not EP0 */
300 #define EPCTRL_RX_DATA_TOGGLE_INH 0x00000020 /* Not EP0 */
301 #define EPCTRL_RX_TYPE 0x0000000C
302 #define EPCTRL_RX_DATA_SINK 0x00000002 /* Not EP0 */
303 #define EPCTRL_RX_EP_STALL 0x00000001
305 /* bit 19-18 and 3-2 are endpoint type */
306 #define EPCTRL_EP_TYPE_CONTROL 0
307 #define EPCTRL_EP_TYPE_ISO 1
308 #define EPCTRL_EP_TYPE_BULK 2
309 #define EPCTRL_EP_TYPE_INTERRUPT 3
310 #define EPCTRL_TX_EP_TYPE_SHIFT 18
311 #define EPCTRL_RX_EP_TYPE_SHIFT 2
313 /* SNOOPn Register Bit Masks */
314 #define SNOOP_ADDRESS_MASK 0xFFFFF000
315 #define SNOOP_SIZE_ZERO 0x00 /* snooping disable */
316 #define SNOOP_SIZE_4KB 0x0B /* 4KB snoop size */
317 #define SNOOP_SIZE_8KB 0x0C
318 #define SNOOP_SIZE_16KB 0x0D
319 #define SNOOP_SIZE_32KB 0x0E
320 #define SNOOP_SIZE_64KB 0x0F
321 #define SNOOP_SIZE_128KB 0x10
322 #define SNOOP_SIZE_256KB 0x11
323 #define SNOOP_SIZE_512KB 0x12
324 #define SNOOP_SIZE_1MB 0x13
325 #define SNOOP_SIZE_2MB 0x14
326 #define SNOOP_SIZE_4MB 0x15
327 #define SNOOP_SIZE_8MB 0x16
328 #define SNOOP_SIZE_16MB 0x17
329 #define SNOOP_SIZE_32MB 0x18
330 #define SNOOP_SIZE_64MB 0x19
331 #define SNOOP_SIZE_128MB 0x1A
332 #define SNOOP_SIZE_256MB 0x1B
333 #define SNOOP_SIZE_512MB 0x1C
334 #define SNOOP_SIZE_1GB 0x1D
335 #define SNOOP_SIZE_2GB 0x1E /* 2GB snoop size */
337 /* pri_ctrl Register Bit Masks */
338 #define PRI_CTRL_PRI_LVL1 0x0000000C
339 #define PRI_CTRL_PRI_LVL0 0x00000003
341 /* si_ctrl Register Bit Masks */
342 #define SI_CTRL_ERR_DISABLE 0x00000010
343 #define SI_CTRL_IDRC_DISABLE 0x00000008
344 #define SI_CTRL_RD_SAFE_EN 0x00000004
345 #define SI_CTRL_RD_PREFETCH_DISABLE 0x00000002
346 #define SI_CTRL_RD_PREFEFETCH_VAL 0x00000001
348 /* control Register Bit Masks */
349 #define USB_CTRL_IOENB 0x00000004
350 #define USB_CTRL_ULPI_INT0EN 0x00000001
352 /* Endpoint Queue Head data struct
353 * Rem: all the variables of qh are LittleEndian Mode
354 * and NEXT_POINTER_MASK should operate on a LittleEndian, Phy Addr
356 struct ep_queue_head
{
357 u32 max_pkt_length
; /* Mult(31-30) , Zlt(29) , Max Pkt len
359 u32 curr_dtd_ptr
; /* Current dTD Pointer(31-5) */
360 u32 next_dtd_ptr
; /* Next dTD Pointer(31-5), T(0) */
361 u32 size_ioc_int_sts
; /* Total bytes (30-16), IOC (15),
362 MultO(11-10), STS (7-0) */
363 u32 buff_ptr0
; /* Buffer pointer Page 0 (31-12) */
364 u32 buff_ptr1
; /* Buffer pointer Page 1 (31-12) */
365 u32 buff_ptr2
; /* Buffer pointer Page 2 (31-12) */
366 u32 buff_ptr3
; /* Buffer pointer Page 3 (31-12) */
367 u32 buff_ptr4
; /* Buffer pointer Page 4 (31-12) */
369 u8 setup_buffer
[8]; /* Setup data 8 bytes */
373 /* Endpoint Queue Head Bit Masks */
374 #define EP_QUEUE_HEAD_MULT_POS 30
375 #define EP_QUEUE_HEAD_ZLT_SEL 0x20000000
376 #define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16
377 #define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff)
378 #define EP_QUEUE_HEAD_IOS 0x00008000
379 #define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001
380 #define EP_QUEUE_HEAD_IOC 0x00008000
381 #define EP_QUEUE_HEAD_MULTO 0x00000C00
382 #define EP_QUEUE_HEAD_STATUS_HALT 0x00000040
383 #define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080
384 #define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF
385 #define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0
386 #define EP_QUEUE_FRINDEX_MASK 0x000007FF
387 #define EP_MAX_LENGTH_TRANSFER 0x4000
389 /* Endpoint Transfer Descriptor data struct */
390 /* Rem: all the variables of td are LittleEndian Mode */
391 struct ep_td_struct
{
392 u32 next_td_ptr
; /* Next TD pointer(31-5), T(0) set
394 u32 size_ioc_sts
; /* Total bytes (30-16), IOC (15),
395 MultO(11-10), STS (7-0) */
396 u32 buff_ptr0
; /* Buffer pointer Page 0 */
397 u32 buff_ptr1
; /* Buffer pointer Page 1 */
398 u32 buff_ptr2
; /* Buffer pointer Page 2 */
399 u32 buff_ptr3
; /* Buffer pointer Page 3 */
400 u32 buff_ptr4
; /* Buffer pointer Page 4 */
403 dma_addr_t td_dma
; /* dma address for this td */
404 /* virtual address of next td specified in next_td_ptr */
405 struct ep_td_struct
*next_td_virt
;
408 /* Endpoint Transfer Descriptor bit Masks */
409 #define DTD_NEXT_TERMINATE 0x00000001
410 #define DTD_IOC 0x00008000
411 #define DTD_STATUS_ACTIVE 0x00000080
412 #define DTD_STATUS_HALTED 0x00000040
413 #define DTD_STATUS_DATA_BUFF_ERR 0x00000020
414 #define DTD_STATUS_TRANSACTION_ERR 0x00000008
415 #define DTD_RESERVED_FIELDS 0x80007300
416 #define DTD_ADDR_MASK 0xFFFFFFE0
417 #define DTD_PACKET_SIZE 0x7FFF0000
418 #define DTD_LENGTH_BIT_POS 16
419 #define DTD_ERROR_MASK (DTD_STATUS_HALTED | \
420 DTD_STATUS_DATA_BUFF_ERR | \
421 DTD_STATUS_TRANSACTION_ERR)
422 /* Alignment requirements; must be a power of two */
423 #define DTD_ALIGNMENT 0x20
424 #define QH_ALIGNMENT 2048
426 /* Controller dma boundary */
427 #define UDC_DMA_BOUNDARY 0x1000
429 /*-------------------------------------------------------------------------*/
431 /* ### driver private data
434 struct usb_request req
;
435 struct list_head queue
;
436 /* ep_queue() func will add
437 a request->queue into a udc_ep->queue 'd tail */
441 struct ep_td_struct
*head
, *tail
; /* For dTD List
442 cpu endian Virtual addr */
443 unsigned int dtd_count
;
446 #define REQ_UNCOMPLETE 1
450 struct list_head queue
;
452 struct ep_queue_head
*qh
;
453 const struct usb_endpoint_descriptor
*desc
;
454 struct usb_gadget
*gadget
;
464 struct usb_gadget gadget
;
465 struct usb_gadget_driver
*driver
;
466 struct fsl_usb2_platform_data
*pdata
;
467 struct completion
*done
; /* to make sure release() is done */
472 struct usb_ctrlrequest local_setup_buff
;
474 struct otg_transceiver
*transceiver
;
475 unsigned softconnect
:1;
476 unsigned vbus_active
:1;
478 unsigned remote_wakeup
:1;
479 unsigned already_stopped
:1;
480 unsigned big_endian_desc
:1;
482 struct ep_queue_head
*ep_qh
; /* Endpoints Queue-Head */
483 struct fsl_req
*status_req
; /* ep0 status request */
484 struct dma_pool
*td_pool
; /* dma pool for DTD */
485 enum fsl_usb2_phy_modes phy_mode
;
487 size_t ep_qh_size
; /* size after alignment adjustment*/
488 dma_addr_t ep_qh_dma
; /* dma address of QH */
490 u32 max_pipes
; /* Device max pipes */
491 u32 bus_reset
; /* Device is bus resetting */
492 u32 resume_state
; /* USB state to resume */
493 u32 usb_state
; /* USB current state */
494 u32 ep0_state
; /* Endpoint zero state */
495 u32 ep0_dir
; /* Endpoint zero direction: can be
496 USB_DIR_IN or USB_DIR_OUT */
497 u8 device_address
; /* Device USB address */
500 /*-------------------------------------------------------------------------*/
503 #define DBG(fmt, args...) printk(KERN_DEBUG "[%s] " fmt "\n", \
506 #define DBG(fmt, args...) do{}while(0)
510 static void dump_msg(const char *label
, const u8
* buf
, unsigned int length
)
512 unsigned int start
, num
, i
;
517 DBG("%s, length %u:\n", label
, length
);
520 num
= min(length
, 16u);
522 for (i
= 0; i
< num
; ++i
) {
525 sprintf(p
, " %02x", buf
[i
]);
529 printk(KERN_DEBUG
"%6x: %s\n", start
, line
);
540 #define VDBG(stuff...) do{}while(0)
543 #define ERR(stuff...) pr_err("udc: " stuff)
544 #define WARNING(stuff...) pr_warning("udc: " stuff)
545 #define INFO(stuff...) pr_info("udc: " stuff)
547 /*-------------------------------------------------------------------------*/
549 /* ### Add board specific defines here
553 * ### pipe direction macro from device view
555 #define USB_RECV 0 /* OUT EP */
556 #define USB_SEND 1 /* IN EP */
559 * ### internal used help routines.
561 #define ep_index(EP) ((EP)->desc->bEndpointAddress&0xF)
562 #define ep_maxpacket(EP) ((EP)->ep.maxpacket)
563 #define ep_is_in(EP) ( (ep_index(EP) == 0) ? (EP->udc->ep0_dir == \
564 USB_DIR_IN ):((EP)->desc->bEndpointAddress \
565 & USB_DIR_IN)==USB_DIR_IN)
566 #define get_ep_by_pipe(udc, pipe) ((pipe == 1)? &udc->eps[0]: \
568 #define get_pipe_by_windex(windex) ((windex & USB_ENDPOINT_NUMBER_MASK) \
569 * 2 + ((windex & USB_DIR_IN) ? 1 : 0))
570 #define get_pipe_by_ep(EP) (ep_index(EP) * 2 + ep_is_in(EP))
572 struct platform_device
;
573 #ifdef CONFIG_ARCH_MXC
574 int fsl_udc_clk_init(struct platform_device
*pdev
);
575 void fsl_udc_clk_finalize(struct platform_device
*pdev
);
576 void fsl_udc_clk_release(void);
578 static inline int fsl_udc_clk_init(struct platform_device
*pdev
)
582 static inline void fsl_udc_clk_finalize(struct platform_device
*pdev
)
585 static inline void fsl_udc_clk_release(void)