drivers/ata/pata_it8213.c

   1 /*
   2  *    pata_it8213.c - iTE Tech. Inc.  IT8213 PATA driver
   3  *
   4  *    The IT8213 is a very Intel ICH like device for timing purposes, having
   5  *    a similar register layout and the same split clock arrangement. Cable
   6  *    detection is different, and it does not have slave channels or all the
   7  *    clutter of later ICH/SATA setups.
   8  */
   9
  10 #include <linux/kernel.h>
  11 #include <linux/module.h>
  12 #include <linux/pci.h>
  13 #include <linux/init.h>
  14 #include <linux/blkdev.h>
  15 #include <linux/delay.h>
  16 #include <linux/device.h>
  17 #include <scsi/scsi_host.h>
  18 #include <linux/libata.h>
  19 #include <linux/ata.h>
  20
  21 #define DRV_NAME        "pata_it8213"
  22 #define DRV_VERSION     "0.0.3"
  23
  24 /**
  25  *      it8213_pre_reset        -       probe begin
  26  *      @link: link
  27  *      @deadline: deadline jiffies for the operation
  28  *
  29  *      Filter out ports by the enable bits before doing the normal reset
  30  *      and probe.
  31  */
  32
  33 static int it8213_pre_reset(struct ata_link *link, unsigned long deadline)
  34 {
  35         static const struct pci_bits it8213_enable_bits[] = {
  36                 { 0x41U, 1U, 0x80UL, 0x80UL },  /* port 0 */
  37         };
  38         struct ata_port *ap = link->ap;
  39         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  40         if (!pci_test_config_bits(pdev, &it8213_enable_bits[ap->port_no]))
  41                 return -ENOENT;
  42
  43         return ata_sff_prereset(link, deadline);
  44 }
  45
  46 /**
  47  *      it8213_cable_detect     -       check for 40/80 pin
  48  *      @ap: Port
  49  *
  50  *      Perform cable detection for the 8213 ATA interface. This is
  51  *      different to the PIIX arrangement
  52  */
  53
  54 static int it8213_cable_detect(struct ata_port *ap)
  55 {
  56         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  57         u8 tmp;
  58         pci_read_config_byte(pdev, 0x42, &tmp);
  59         if (tmp & 2)    /* The initial docs are incorrect */
  60                 return ATA_CBL_PATA40;
  61         return ATA_CBL_PATA80;
  62 }
  63
  64 /**
  65  *      it8213_set_piomode - Initialize host controller PATA PIO timings
  66  *      @ap: Port whose timings we are configuring
  67  *      @adev: Device whose timings we are configuring
  68  *
  69  *      Set PIO mode for device, in host controller PCI config space.
  70  *
  71  *      LOCKING:
  72  *      None (inherited from caller).
  73  */
  74
  75 static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev)
  76 {
  77         unsigned int pio        = adev->pio_mode - XFER_PIO_0;
  78         struct pci_dev *dev     = to_pci_dev(ap->host->dev);
  79         unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
  80         u16 idetm_data;
  81         int control = 0;
  82
  83         /*
  84          *      See Intel Document 298600-004 for the timing programing rules
  85          *      for PIIX/ICH. The 8213 is a clone so very similar
  86          */
  87
  88         static const     /* ISP  RTC */
  89         u8 timings[][2] = { { 0, 0 },
  90                             { 0, 0 },
  91                             { 1, 0 },
  92                             { 2, 1 },
  93                             { 2, 3 }, };
  94
  95         if (pio > 1)
  96                 control |= 1;   /* TIME */
  97         if (ata_pio_need_iordy(adev))   /* PIO 3/4 require IORDY */
  98                 control |= 2;   /* IE */
  99         /* Bit 2 is set for ATAPI on the IT8213 - reverse of ICH/PIIX */
 100         if (adev->class != ATA_DEV_ATA)
 101                 control |= 4;   /* PPE */
 102
 103         pci_read_config_word(dev, idetm_port, &idetm_data);
 104
 105         /* Set PPE, IE, and TIME as appropriate */
 106         if (adev->devno == 0) {
 107                 idetm_data &= 0xCCF0;
 108                 idetm_data |= control;
 109                 idetm_data |= (timings[pio][0] << 12) |
 110                         (timings[pio][1] << 8);
 111         } else {
 112                 u8 slave_data;
 113
 114                 idetm_data &= 0xFF0F;
 115                 idetm_data |= (control << 4);
 116
 117                 /* Slave timing in separate register */
 118                 pci_read_config_byte(dev, 0x44, &slave_data);
 119                 slave_data &= 0xF0;
 120                 slave_data |= (timings[pio][0] << 2) | timings[pio][1];
 121                 pci_write_config_byte(dev, 0x44, slave_data);
 122         }
 123
 124         idetm_data |= 0x4000;   /* Ensure SITRE is set */
 125         pci_write_config_word(dev, idetm_port, idetm_data);
 126 }
 127
 128 /**
 129  *      it8213_set_dmamode - Initialize host controller PATA DMA timings
 130  *      @ap: Port whose timings we are configuring
 131  *      @adev: Device to program
 132  *
 133  *      Set UDMA/MWDMA mode for device, in host controller PCI config space.
 134  *      This device is basically an ICH alike.
 135  *
 136  *      LOCKING:
 137  *      None (inherited from caller).
 138  */
 139
 140 static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 141 {
 142         struct pci_dev *dev     = to_pci_dev(ap->host->dev);
 143         u16 master_data;
 144         u8 speed                = adev->dma_mode;
 145         int devid               = adev->devno;
 146         u8 udma_enable;
 147
 148         static const     /* ISP  RTC */
 149         u8 timings[][2] = { { 0, 0 },
 150                             { 0, 0 },
 151                             { 1, 0 },
 152                             { 2, 1 },
 153                             { 2, 3 }, };
 154
 155         pci_read_config_word(dev, 0x40, &master_data);
 156         pci_read_config_byte(dev, 0x48, &udma_enable);
 157
 158         if (speed >= XFER_UDMA_0) {
 159                 unsigned int udma = adev->dma_mode - XFER_UDMA_0;
 160                 u16 udma_timing;
 161                 u16 ideconf;
 162                 int u_clock, u_speed;
 163
 164                 /* Clocks follow the PIIX style */
 165                 u_speed = min(2 - (udma & 1), udma);
 166                 if (udma == 5)
 167                         u_clock = 0x1000;       /* 100Mhz */
 168                 else if (udma > 2)
 169                         u_clock = 1;            /* 66Mhz */
 170                 else
 171                         u_clock = 0;            /* 33Mhz */
 172
 173                 udma_enable |= (1 << devid);
 174
 175                 /* Load the UDMA cycle time */
 176                 pci_read_config_word(dev, 0x4A, &udma_timing);
 177                 udma_timing &= ~(3 << (4 * devid));
 178                 udma_timing |= u_speed << (4 * devid);
 179                 pci_write_config_word(dev, 0x4A, udma_timing);
 180
 181                 /* Load the clock selection */
 182                 pci_read_config_word(dev, 0x54, &ideconf);
 183                 ideconf &= ~(0x1001 << devid);
 184                 ideconf |= u_clock << devid;
 185                 pci_write_config_word(dev, 0x54, ideconf);
 186         } else {
 187                 /*
 188                  * MWDMA is driven by the PIO timings. We must also enable
 189                  * IORDY unconditionally along with TIME1. PPE has already
 190                  * been set when the PIO timing was set.
 191                  */
 192                 unsigned int mwdma      = adev->dma_mode - XFER_MW_DMA_0;
 193                 unsigned int control;
 194                 u8 slave_data;
 195                 static const unsigned int needed_pio[3] = {
 196                         XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
 197                 };
 198                 int pio = needed_pio[mwdma] - XFER_PIO_0;
 199
 200                 control = 3;    /* IORDY|TIME1 */
 201
 202                 /* If the drive MWDMA is faster than it can do PIO then
 203                    we must force PIO into PIO0 */
 204
 205                 if (adev->pio_mode < needed_pio[mwdma])
 206                         /* Enable DMA timing only */
 207                         control |= 8;   /* PIO cycles in PIO0 */
 208
 209                 if (devid) {    /* Slave */
 210                         master_data &= 0xFF4F;  /* Mask out IORDY|TIME1|DMAONLY */
 211                         master_data |= control << 4;
 212                         pci_read_config_byte(dev, 0x44, &slave_data);
 213                         slave_data &= 0xF0;
 214                         /* Load the matching timing */
 215                         slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
 216                         pci_write_config_byte(dev, 0x44, slave_data);
 217                 } else {        /* Master */
 218                         master_data &= 0xCCF4;  /* Mask out IORDY|TIME1|DMAONLY
 219                                                    and master timing bits */
 220                         master_data |= control;
 221                         master_data |=
 222                                 (timings[pio][0] << 12) |
 223                                 (timings[pio][1] << 8);
 224                 }
 225                 udma_enable &= ~(1 << devid);
 226                 pci_write_config_word(dev, 0x40, master_data);
 227         }
 228         pci_write_config_byte(dev, 0x48, udma_enable);
 229 }
 230
 231 static struct scsi_host_template it8213_sht = {
 232         ATA_BMDMA_SHT(DRV_NAME),
 233 };
 234
 235
 236 static struct ata_port_operations it8213_ops = {
 237         .inherits               = &ata_bmdma_port_ops,
 238         .cable_detect           = it8213_cable_detect,
 239         .set_piomode            = it8213_set_piomode,
 240         .set_dmamode            = it8213_set_dmamode,
 241         .prereset               = it8213_pre_reset,
 242 };
 243
 244
 245 /**
 246  *      it8213_init_one - Register 8213 ATA PCI device with kernel services
 247  *      @pdev: PCI device to register
 248  *      @ent: Entry in it8213_pci_tbl matching with @pdev
 249  *
 250  *      Called from kernel PCI layer.
 251  *
 252  *      LOCKING:
 253  *      Inherited from PCI layer (may sleep).
 254  *
 255  *      RETURNS:
 256  *      Zero on success, or -ERRNO value.
 257  */
 258
 259 static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 260 {
 261         static const struct ata_port_info info = {
 262                 .flags          = ATA_FLAG_SLAVE_POSS,
 263                 .pio_mask       = ATA_PIO4,
 264                 .mwdma_mask     = ATA_MWDMA12_ONLY,
 265                 .udma_mask      = ATA_UDMA4, /* FIXME: want UDMA 100? */
 266                 .port_ops       = &it8213_ops,
 267         };
 268         /* Current IT8213 stuff is single port */
 269         const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
 270
 271         ata_print_version_once(&pdev->dev, DRV_VERSION);
 272
 273         return ata_pci_bmdma_init_one(pdev, ppi, &it8213_sht, NULL, 0);
 274 }
 275
 276 static const struct pci_device_id it8213_pci_tbl[] = {
 277         { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8213), },
 278
 279         { }     /* terminate list */
 280 };
 281
 282 static struct pci_driver it8213_pci_driver = {
 283         .name                   = DRV_NAME,
 284         .id_table               = it8213_pci_tbl,
 285         .probe                  = it8213_init_one,
 286         .remove                 = ata_pci_remove_one,
 287 #ifdef CONFIG_PM
 288         .suspend                = ata_pci_device_suspend,
 289         .resume                 = ata_pci_device_resume,
 290 #endif
 291 };
 292
 293 static int __init it8213_init(void)
 294 {
 295         return pci_register_driver(&it8213_pci_driver);
 296 }
 297
 298 static void __exit it8213_exit(void)
 299 {
 300         pci_unregister_driver(&it8213_pci_driver);
 301 }
 302
 303 module_init(it8213_init);
 304 module_exit(it8213_exit);
 305
 306 MODULE_AUTHOR("Alan Cox");
 307 MODULE_DESCRIPTION("SCSI low-level driver for the ITE 8213");
 308 MODULE_LICENSE("GPL");
 309 MODULE_DEVICE_TABLE(pci, it8213_pci_tbl);
 310 MODULE_VERSION(DRV_VERSION);