2 * DM355 leopard board support
4 * Based on board-dm355-evm.c
6 * This file is licensed under the terms of the GNU General Public
7 * License version 2. This program is licensed "as is" without any
8 * warranty of any kind, whether express or implied.
10 #include <linux/kernel.h>
11 #include <linux/init.h>
12 #include <linux/err.h>
13 #include <linux/platform_device.h>
14 #include <linux/mtd/mtd.h>
15 #include <linux/mtd/partitions.h>
16 #include <linux/mtd/nand.h>
17 #include <linux/i2c.h>
18 #include <linux/gpio.h>
19 #include <linux/clk.h>
20 #include <linux/spi/spi.h>
21 #include <linux/spi/eeprom.h>
23 #include <asm/mach-types.h>
24 #include <asm/mach/arch.h>
26 #include <mach/dm355.h>
28 #include <mach/serial.h>
29 #include <mach/nand.h>
33 /* NOTE: this is geared for the standard config, with a socketed
34 * 2 GByte Micron NAND (MT29F16G08FAA) using 128KB sectors. If you
35 * swap chips, maybe with a different block size, partitioning may
38 #define NAND_BLOCK_SIZE SZ_128K
40 static struct mtd_partition davinci_nand_partitions
[] = {
42 /* UBL (a few copies) plus U-Boot */
45 .size
= 15 * NAND_BLOCK_SIZE
,
46 .mask_flags
= MTD_WRITEABLE
, /* force read-only */
48 /* U-Boot environment */
50 .offset
= MTDPART_OFS_APPEND
,
51 .size
= 1 * NAND_BLOCK_SIZE
,
55 .offset
= MTDPART_OFS_APPEND
,
59 .name
= "filesystem1",
60 .offset
= MTDPART_OFS_APPEND
,
64 .name
= "filesystem2",
65 .offset
= MTDPART_OFS_APPEND
,
66 .size
= MTDPART_SIZ_FULL
,
69 /* two blocks with bad block table (and mirror) at the end */
72 static struct davinci_nand_pdata davinci_nand_data
= {
73 .mask_chipsel
= BIT(14),
74 .parts
= davinci_nand_partitions
,
75 .nr_parts
= ARRAY_SIZE(davinci_nand_partitions
),
76 .ecc_mode
= NAND_ECC_HW_SYNDROME
,
77 .options
= NAND_USE_FLASH_BBT
,
80 static struct resource davinci_nand_resources
[] = {
82 .start
= DM355_ASYNC_EMIF_DATA_CE0_BASE
,
83 .end
= DM355_ASYNC_EMIF_DATA_CE0_BASE
+ SZ_32M
- 1,
84 .flags
= IORESOURCE_MEM
,
86 .start
= DM355_ASYNC_EMIF_CONTROL_BASE
,
87 .end
= DM355_ASYNC_EMIF_CONTROL_BASE
+ SZ_4K
- 1,
88 .flags
= IORESOURCE_MEM
,
92 static struct platform_device davinci_nand_device
= {
93 .name
= "davinci_nand",
96 .num_resources
= ARRAY_SIZE(davinci_nand_resources
),
97 .resource
= davinci_nand_resources
,
100 .platform_data
= &davinci_nand_data
,
104 static struct davinci_i2c_platform_data i2c_pdata
= {
105 .bus_freq
= 400 /* kHz */,
106 .bus_delay
= 0 /* usec */,
109 static int leopard_mmc_gpio
= -EINVAL
;
111 static void dm355leopard_mmcsd_gpios(unsigned gpio
)
113 gpio_request(gpio
+ 0, "mmc0_ro");
114 gpio_request(gpio
+ 1, "mmc0_cd");
115 gpio_request(gpio
+ 2, "mmc1_ro");
116 gpio_request(gpio
+ 3, "mmc1_cd");
118 /* we "know" these are input-only so we don't
119 * need to call gpio_direction_input()
122 leopard_mmc_gpio
= gpio
;
125 static struct i2c_board_info dm355leopard_i2c_info
[] = {
126 { I2C_BOARD_INFO("dm355leopard_msp", 0x25),
127 .platform_data
= dm355leopard_mmcsd_gpios
,
129 /* { I2C_BOARD_INFO("tlv320aic3x", 0x1b), }, */
130 /* { I2C_BOARD_INFO("tvp5146", 0x5d), }, */
133 static void __init
leopard_init_i2c(void)
135 davinci_init_i2c(&i2c_pdata
);
137 gpio_request(5, "dm355leopard_msp");
138 gpio_direction_input(5);
139 dm355leopard_i2c_info
[0].irq
= gpio_to_irq(5);
141 i2c_register_board_info(1, dm355leopard_i2c_info
,
142 ARRAY_SIZE(dm355leopard_i2c_info
));
145 static struct resource dm355leopard_dm9000_rsrc
[] = {
150 .flags
= IORESOURCE_MEM
,
155 .flags
= IORESOURCE_MEM
,
157 .flags
= IORESOURCE_IRQ
158 | IORESOURCE_IRQ_HIGHEDGE
/* rising (active high) */,
162 static struct platform_device dm355leopard_dm9000
= {
165 .resource
= dm355leopard_dm9000_rsrc
,
166 .num_resources
= ARRAY_SIZE(dm355leopard_dm9000_rsrc
),
169 static struct platform_device
*davinci_leopard_devices
[] __initdata
= {
170 &dm355leopard_dm9000
,
171 &davinci_nand_device
,
174 static struct davinci_uart_config uart_config __initdata
= {
175 .enabled_uarts
= (1 << 0),
178 static void __init
dm355_leopard_map_io(void)
183 static int dm355leopard_mmc_get_cd(int module
)
185 if (!gpio_is_valid(leopard_mmc_gpio
))
187 /* low == card present */
188 return !gpio_get_value_cansleep(leopard_mmc_gpio
+ 2 * module
+ 1);
191 static int dm355leopard_mmc_get_ro(int module
)
193 if (!gpio_is_valid(leopard_mmc_gpio
))
195 /* high == card's write protect switch active */
196 return gpio_get_value_cansleep(leopard_mmc_gpio
+ 2 * module
+ 0);
199 static struct davinci_mmc_config dm355leopard_mmc_config
= {
200 .get_cd
= dm355leopard_mmc_get_cd
,
201 .get_ro
= dm355leopard_mmc_get_ro
,
203 .max_freq
= 50000000,
204 .caps
= MMC_CAP_MMC_HIGHSPEED
| MMC_CAP_SD_HIGHSPEED
,
207 /* Don't connect anything to J10 unless you're only using USB host
208 * mode *and* have to do so with some kind of gender-bender. If
209 * you have proper Mini-B or Mini-A cables (or Mini-A adapters)
210 * the ID pin won't need any help.
212 #ifdef CONFIG_USB_MUSB_PERIPHERAL
213 #define USB_ID_VALUE 0 /* ID pulled high; *should* float */
215 #define USB_ID_VALUE 1 /* ID pulled low */
218 static struct spi_eeprom at25640a
= {
219 .byte_len
= SZ_64K
/ 8,
225 static struct spi_board_info dm355_leopard_spi_info
[] __initconst
= {
228 .platform_data
= &at25640a
,
229 .max_speed_hz
= 10 * 1000 * 1000, /* at 3v3 */
236 static __init
void dm355_leopard_init(void)
240 gpio_request(9, "dm9000");
241 gpio_direction_input(9);
242 dm355leopard_dm9000_rsrc
[2].start
= gpio_to_irq(9);
244 aemif
= clk_get(&dm355leopard_dm9000
.dev
, "aemif");
246 WARN("%s: unable to get AEMIF clock\n", __func__
);
250 platform_add_devices(davinci_leopard_devices
,
251 ARRAY_SIZE(davinci_leopard_devices
));
253 davinci_serial_init(&uart_config
);
255 /* NOTE: NAND flash timings set by the UBL are slower than
256 * needed by MT29F16G08FAA chips ... EMIF.A1CR is 0x40400204
257 * but could be 0x0400008c for about 25% faster page reads.
260 gpio_request(2, "usb_id_toggle");
261 gpio_direction_output(2, USB_ID_VALUE
);
262 /* irlml6401 switches over 1A in under 8 msec */
263 davinci_setup_usb(1000, 8);
265 davinci_setup_mmc(0, &dm355leopard_mmc_config
);
266 davinci_setup_mmc(1, &dm355leopard_mmc_config
);
268 dm355_init_spi0(BIT(0), dm355_leopard_spi_info
,
269 ARRAY_SIZE(dm355_leopard_spi_info
));
272 MACHINE_START(DM355_LEOPARD
, "DaVinci DM355 leopard")
273 .boot_params
= (0x80000100),
274 .map_io
= dm355_leopard_map_io
,
275 .init_irq
= davinci_irq_init
,
276 .timer
= &davinci_timer
,
277 .init_machine
= dm355_leopard_init
,