Add linux-next specific files for 20110831
[linux-2.6/next.git] / drivers / media / video / em28xx / em28xx-reg.h
blob66f792361b97dee12d7b91c9839c12f71600f8a2
1 #define EM_GPIO_0 (1 << 0)
2 #define EM_GPIO_1 (1 << 1)
3 #define EM_GPIO_2 (1 << 2)
4 #define EM_GPIO_3 (1 << 3)
5 #define EM_GPIO_4 (1 << 4)
6 #define EM_GPIO_5 (1 << 5)
7 #define EM_GPIO_6 (1 << 6)
8 #define EM_GPIO_7 (1 << 7)
10 #define EM_GPO_0 (1 << 0)
11 #define EM_GPO_1 (1 << 1)
12 #define EM_GPO_2 (1 << 2)
13 #define EM_GPO_3 (1 << 3)
15 /* em2800 registers */
16 #define EM2800_R08_AUDIOSRC 0x08
18 /* em28xx registers */
20 #define EM28XX_R00_CHIPCFG 0x00
22 /* em28xx Chip Configuration 0x00 */
23 #define EM28XX_CHIPCFG_VENDOR_AUDIO 0x80
24 #define EM28XX_CHIPCFG_I2S_VOLUME_CAPABLE 0x40
25 #define EM28XX_CHIPCFG_I2S_5_SAMPRATES 0x30
26 #define EM28XX_CHIPCFG_I2S_3_SAMPRATES 0x20
27 #define EM28XX_CHIPCFG_AC97 0x10
28 #define EM28XX_CHIPCFG_AUDIOMASK 0x30
30 #define EM28XX_R01_CHIPCFG2 0x01
32 /* em28xx Chip Configuration 2 0x01 */
33 #define EM28XX_CHIPCFG2_TS_PRESENT 0x10
34 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_MASK 0x0c /* bits 3-2 */
35 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_1MF 0x00
36 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_2MF 0x04
37 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_4MF 0x08
38 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_8MF 0x0c
39 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_MASK 0x03 /* bits 0-1 */
40 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_188 0x00
41 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_376 0x01
42 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_564 0x02
43 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_752 0x03
46 /* GPIO/GPO registers */
47 #define EM2880_R04_GPO 0x04 /* em2880-em2883 only */
48 #define EM28XX_R08_GPIO 0x08 /* em2820 or upper */
50 #define EM28XX_R06_I2C_CLK 0x06
52 /* em28xx I2C Clock Register (0x06) */
53 #define EM28XX_I2C_CLK_ACK_LAST_READ 0x80
54 #define EM28XX_I2C_CLK_WAIT_ENABLE 0x40
55 #define EM28XX_I2C_EEPROM_ON_BOARD 0x08
56 #define EM28XX_I2C_EEPROM_KEY_VALID 0x04
57 #define EM2874_I2C_SECONDARY_BUS_SELECT 0x04 /* em2874 has two i2c busses */
58 #define EM28XX_I2C_FREQ_1_5_MHZ 0x03 /* bus frequency (bits [1-0]) */
59 #define EM28XX_I2C_FREQ_25_KHZ 0x02
60 #define EM28XX_I2C_FREQ_400_KHZ 0x01
61 #define EM28XX_I2C_FREQ_100_KHZ 0x00
64 #define EM28XX_R0A_CHIPID 0x0a
65 #define EM28XX_R0C_USBSUSP 0x0c /* */
67 #define EM28XX_R0E_AUDIOSRC 0x0e
68 #define EM28XX_R0F_XCLK 0x0f
70 /* em28xx XCLK Register (0x0f) */
71 #define EM28XX_XCLK_AUDIO_UNMUTE 0x80 /* otherwise audio muted */
72 #define EM28XX_XCLK_I2S_MSB_TIMING 0x40 /* otherwise standard timing */
73 #define EM28XX_XCLK_IR_RC5_MODE 0x20 /* otherwise NEC mode */
74 #define EM28XX_XCLK_IR_NEC_CHK_PARITY 0x10
75 #define EM28XX_XCLK_FREQUENCY_30MHZ 0x00 /* Freq. select (bits [3-0]) */
76 #define EM28XX_XCLK_FREQUENCY_15MHZ 0x01
77 #define EM28XX_XCLK_FREQUENCY_10MHZ 0x02
78 #define EM28XX_XCLK_FREQUENCY_7_5MHZ 0x03
79 #define EM28XX_XCLK_FREQUENCY_6MHZ 0x04
80 #define EM28XX_XCLK_FREQUENCY_5MHZ 0x05
81 #define EM28XX_XCLK_FREQUENCY_4_3MHZ 0x06
82 #define EM28XX_XCLK_FREQUENCY_12MHZ 0x07
83 #define EM28XX_XCLK_FREQUENCY_20MHZ 0x08
84 #define EM28XX_XCLK_FREQUENCY_20MHZ_2 0x09
85 #define EM28XX_XCLK_FREQUENCY_48MHZ 0x0a
86 #define EM28XX_XCLK_FREQUENCY_24MHZ 0x0b
88 #define EM28XX_R10_VINMODE 0x10
90 #define EM28XX_R11_VINCTRL 0x11
92 /* em28xx Video Input Control Register 0x11 */
93 #define EM28XX_VINCTRL_VBI_SLICED 0x80
94 #define EM28XX_VINCTRL_VBI_RAW 0x40
95 #define EM28XX_VINCTRL_VOUT_MODE_IN 0x20 /* HREF,VREF,VACT in output */
96 #define EM28XX_VINCTRL_CCIR656_ENABLE 0x10
97 #define EM28XX_VINCTRL_VBI_16BIT_RAW 0x08 /* otherwise 8-bit raw */
98 #define EM28XX_VINCTRL_FID_ON_HREF 0x04
99 #define EM28XX_VINCTRL_DUAL_EDGE_STROBE 0x02
100 #define EM28XX_VINCTRL_INTERLACED 0x01
102 #define EM28XX_R12_VINENABLE 0x12 /* */
104 #define EM28XX_R14_GAMMA 0x14
105 #define EM28XX_R15_RGAIN 0x15
106 #define EM28XX_R16_GGAIN 0x16
107 #define EM28XX_R17_BGAIN 0x17
108 #define EM28XX_R18_ROFFSET 0x18
109 #define EM28XX_R19_GOFFSET 0x19
110 #define EM28XX_R1A_BOFFSET 0x1a
112 #define EM28XX_R1B_OFLOW 0x1b
113 #define EM28XX_R1C_HSTART 0x1c
114 #define EM28XX_R1D_VSTART 0x1d
115 #define EM28XX_R1E_CWIDTH 0x1e
116 #define EM28XX_R1F_CHEIGHT 0x1f
118 #define EM28XX_R20_YGAIN 0x20
119 #define EM28XX_R21_YOFFSET 0x21
120 #define EM28XX_R22_UVGAIN 0x22
121 #define EM28XX_R23_UOFFSET 0x23
122 #define EM28XX_R24_VOFFSET 0x24
123 #define EM28XX_R25_SHARPNESS 0x25
125 #define EM28XX_R26_COMPR 0x26
126 #define EM28XX_R27_OUTFMT 0x27
128 /* em28xx Output Format Register (0x27) */
129 #define EM28XX_OUTFMT_RGB_8_RGRG 0x00
130 #define EM28XX_OUTFMT_RGB_8_GRGR 0x01
131 #define EM28XX_OUTFMT_RGB_8_GBGB 0x02
132 #define EM28XX_OUTFMT_RGB_8_BGBG 0x03
133 #define EM28XX_OUTFMT_RGB_16_656 0x04
134 #define EM28XX_OUTFMT_RGB_8_BAYER 0x08 /* Pattern in Reg 0x10[1-0] */
135 #define EM28XX_OUTFMT_YUV211 0x10
136 #define EM28XX_OUTFMT_YUV422_Y0UY1V 0x14
137 #define EM28XX_OUTFMT_YUV422_Y1UY0V 0x15
138 #define EM28XX_OUTFMT_YUV411 0x18
141 #define EM28XX_R28_XMIN 0x28
142 #define EM28XX_R29_XMAX 0x29
143 #define EM28XX_R2A_YMIN 0x2a
144 #define EM28XX_R2B_YMAX 0x2b
146 #define EM28XX_R30_HSCALELOW 0x30
147 #define EM28XX_R31_HSCALEHIGH 0x31
148 #define EM28XX_R32_VSCALELOW 0x32
149 #define EM28XX_R33_VSCALEHIGH 0x33
150 #define EM28XX_R34_VBI_START_H 0x34
151 #define EM28XX_R35_VBI_START_V 0x35
152 #define EM28XX_R36_VBI_WIDTH 0x36
153 #define EM28XX_R37_VBI_HEIGHT 0x37
155 #define EM28XX_R40_AC97LSB 0x40
156 #define EM28XX_R41_AC97MSB 0x41
157 #define EM28XX_R42_AC97ADDR 0x42
158 #define EM28XX_R43_AC97BUSY 0x43
160 #define EM28XX_R45_IR 0x45
161 /* 0x45 bit 7 - parity bit
162 bits 6-0 - count
163 0x46 IR brand
164 0x47 IR data
167 /* em2874 registers */
168 #define EM2874_R50_IR_CONFIG 0x50
169 #define EM2874_R51_IR 0x51
170 #define EM2874_R5F_TS_ENABLE 0x5f
171 #define EM2874_R80_GPIO 0x80
173 /* em2874 IR config register (0x50) */
174 #define EM2874_IR_NEC 0x00
175 #define EM2874_IR_RC5 0x04
176 #define EM2874_IR_RC6_MODE_0 0x08
177 #define EM2874_IR_RC6_MODE_6A 0x0b
179 /* em2874 Transport Stream Enable Register (0x5f) */
180 #define EM2874_TS1_CAPTURE_ENABLE (1 << 0)
181 #define EM2874_TS1_FILTER_ENABLE (1 << 1)
182 #define EM2874_TS1_NULL_DISCARD (1 << 2)
183 #define EM2874_TS2_CAPTURE_ENABLE (1 << 4)
184 #define EM2874_TS2_FILTER_ENABLE (1 << 5)
185 #define EM2874_TS2_NULL_DISCARD (1 << 6)
187 /* register settings */
188 #define EM2800_AUDIO_SRC_TUNER 0x0d
189 #define EM2800_AUDIO_SRC_LINE 0x0c
190 #define EM28XX_AUDIO_SRC_TUNER 0xc0
191 #define EM28XX_AUDIO_SRC_LINE 0x80
193 /* FIXME: Need to be populated with the other chip ID's */
194 enum em28xx_chip_id {
195 CHIP_ID_EM2800 = 7,
196 CHIP_ID_EM2710 = 17,
197 CHIP_ID_EM2820 = 18, /* Also used by some em2710 */
198 CHIP_ID_EM2840 = 20,
199 CHIP_ID_EM2750 = 33,
200 CHIP_ID_EM2860 = 34,
201 CHIP_ID_EM2870 = 35,
202 CHIP_ID_EM2883 = 36,
203 CHIP_ID_EM2874 = 65,
204 CHIP_ID_EM2884 = 68,
205 CHIP_ID_EM28174 = 113,
209 * Registers used by em202 and other AC97 chips
212 /* Standard AC97 registers */
213 #define AC97_RESET 0x00
215 /* Output volumes */
216 #define AC97_MASTER_VOL 0x02
217 #define AC97_LINE_LEVEL_VOL 0x04 /* Some devices use for headphones */
218 #define AC97_MASTER_MONO_VOL 0x06
220 /* Input volumes */
221 #define AC97_PC_BEEP_VOL 0x0a
222 #define AC97_PHONE_VOL 0x0c
223 #define AC97_MIC_VOL 0x0e
224 #define AC97_LINEIN_VOL 0x10
225 #define AC97_CD_VOL 0x12
226 #define AC97_VIDEO_VOL 0x14
227 #define AC97_AUX_VOL 0x16
228 #define AC97_PCM_OUT_VOL 0x18
230 /* capture registers */
231 #define AC97_RECORD_SELECT 0x1a
232 #define AC97_RECORD_GAIN 0x1c
234 /* control registers */
235 #define AC97_GENERAL_PURPOSE 0x20
236 #define AC97_3D_CTRL 0x22
237 #define AC97_AUD_INT_AND_PAG 0x24
238 #define AC97_POWER_DOWN_CTRL 0x26
239 #define AC97_EXT_AUD_ID 0x28
240 #define AC97_EXT_AUD_CTRL 0x2a
242 /* Supported rate varies for each AC97 device
243 if write an unsupported value, it will return the closest one
245 #define AC97_PCM_OUT_FRONT_SRATE 0x2c
246 #define AC97_PCM_OUT_SURR_SRATE 0x2e
247 #define AC97_PCM_OUT_LFE_SRATE 0x30
248 #define AC97_PCM_IN_SRATE 0x32
250 /* For devices with more than 2 channels, extra output volumes */
251 #define AC97_LFE_MASTER_VOL 0x36
252 #define AC97_SURR_MASTER_VOL 0x38
254 /* Digital SPDIF output control */
255 #define AC97_SPDIF_OUT_CTRL 0x3a
257 /* Vendor ID identifier */
258 #define AC97_VENDOR_ID1 0x7c
259 #define AC97_VENDOR_ID2 0x7e
261 /* EMP202 vendor registers */
262 #define EM202_EXT_MODEM_CTRL 0x3e
263 #define EM202_GPIO_CONF 0x4c
264 #define EM202_GPIO_POLARITY 0x4e
265 #define EM202_GPIO_STICKY 0x50
266 #define EM202_GPIO_MASK 0x52
267 #define EM202_GPIO_STATUS 0x54
268 #define EM202_SPDIF_OUT_SEL 0x6a
269 #define EM202_ANTIPOP 0x72
270 #define EM202_EAPD_GPIO_ACCESS 0x74