1 /*******************************************************************************
3 Intel 10 Gigabit PCI Express Linux driver
4 Copyright(c) 1999 - 2011 Intel Corporation.
6 This program is free software; you can redistribute it and/or modify it
7 under the terms and conditions of the GNU General Public License,
8 version 2, as published by the Free Software Foundation.
10 This program is distributed in the hope it will be useful, but WITHOUT
11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
15 You should have received a copy of the GNU General Public License along with
16 this program; if not, write to the Free Software Foundation, Inc.,
17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
19 The full GNU General Public License is included in this distribution in
20 the file called "COPYING".
23 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
24 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
26 *******************************************************************************/
28 #include <linux/pci.h>
29 #include <linux/delay.h>
30 #include <linux/sched.h>
33 #include "ixgbe_phy.h"
35 #define IXGBE_82598_MAX_TX_QUEUES 32
36 #define IXGBE_82598_MAX_RX_QUEUES 64
37 #define IXGBE_82598_RAR_ENTRIES 16
38 #define IXGBE_82598_MC_TBL_SIZE 128
39 #define IXGBE_82598_VFT_TBL_SIZE 128
40 #define IXGBE_82598_RX_PB_SIZE 512
42 static s32
ixgbe_setup_copper_link_82598(struct ixgbe_hw
*hw
,
43 ixgbe_link_speed speed
,
45 bool autoneg_wait_to_complete
);
46 static s32
ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw
*hw
, u8 byte_offset
,
50 * ixgbe_set_pcie_completion_timeout - set pci-e completion timeout
51 * @hw: pointer to the HW structure
53 * The defaults for 82598 should be in the range of 50us to 50ms,
54 * however the hardware default for these parts is 500us to 1ms which is less
55 * than the 10ms recommended by the pci-e spec. To address this we need to
56 * increase the value to either 10ms to 250ms for capability version 1 config,
57 * or 16ms to 55ms for version 2.
59 static void ixgbe_set_pcie_completion_timeout(struct ixgbe_hw
*hw
)
61 struct ixgbe_adapter
*adapter
= hw
->back
;
62 u32 gcr
= IXGBE_READ_REG(hw
, IXGBE_GCR
);
65 /* only take action if timeout value is defaulted to 0 */
66 if (gcr
& IXGBE_GCR_CMPL_TMOUT_MASK
)
70 * if capababilities version is type 1 we can write the
71 * timeout of 10ms to 250ms through the GCR register
73 if (!(gcr
& IXGBE_GCR_CAP_VER2
)) {
74 gcr
|= IXGBE_GCR_CMPL_TMOUT_10ms
;
79 * for version 2 capabilities we need to write the config space
80 * directly in order to set the completion timeout value for
83 pci_read_config_word(adapter
->pdev
,
84 IXGBE_PCI_DEVICE_CONTROL2
, &pcie_devctl2
);
85 pcie_devctl2
|= IXGBE_PCI_DEVICE_CONTROL2_16ms
;
86 pci_write_config_word(adapter
->pdev
,
87 IXGBE_PCI_DEVICE_CONTROL2
, pcie_devctl2
);
89 /* disable completion timeout resend */
90 gcr
&= ~IXGBE_GCR_CMPL_TMOUT_RESEND
;
91 IXGBE_WRITE_REG(hw
, IXGBE_GCR
, gcr
);
95 * ixgbe_get_pcie_msix_count_82598 - Gets MSI-X vector count
96 * @hw: pointer to hardware structure
98 * Read PCIe configuration space, and get the MSI-X vector count from
99 * the capabilities table.
101 static u16
ixgbe_get_pcie_msix_count_82598(struct ixgbe_hw
*hw
)
103 struct ixgbe_adapter
*adapter
= hw
->back
;
105 pci_read_config_word(adapter
->pdev
, IXGBE_PCIE_MSIX_82598_CAPS
,
107 msix_count
&= IXGBE_PCIE_MSIX_TBL_SZ_MASK
;
109 /* MSI-X count is zero-based in HW, so increment to give proper value */
117 static s32
ixgbe_get_invariants_82598(struct ixgbe_hw
*hw
)
119 struct ixgbe_mac_info
*mac
= &hw
->mac
;
121 /* Call PHY identify routine to get the phy type */
122 ixgbe_identify_phy_generic(hw
);
124 mac
->mcft_size
= IXGBE_82598_MC_TBL_SIZE
;
125 mac
->vft_size
= IXGBE_82598_VFT_TBL_SIZE
;
126 mac
->num_rar_entries
= IXGBE_82598_RAR_ENTRIES
;
127 mac
->max_rx_queues
= IXGBE_82598_MAX_RX_QUEUES
;
128 mac
->max_tx_queues
= IXGBE_82598_MAX_TX_QUEUES
;
129 mac
->max_msix_vectors
= ixgbe_get_pcie_msix_count_82598(hw
);
135 * ixgbe_init_phy_ops_82598 - PHY/SFP specific init
136 * @hw: pointer to hardware structure
138 * Initialize any function pointers that were not able to be
139 * set during get_invariants because the PHY/SFP type was
140 * not known. Perform the SFP init if necessary.
143 static s32
ixgbe_init_phy_ops_82598(struct ixgbe_hw
*hw
)
145 struct ixgbe_mac_info
*mac
= &hw
->mac
;
146 struct ixgbe_phy_info
*phy
= &hw
->phy
;
148 u16 list_offset
, data_offset
;
150 /* Identify the PHY */
151 phy
->ops
.identify(hw
);
153 /* Overwrite the link function pointers if copper PHY */
154 if (mac
->ops
.get_media_type(hw
) == ixgbe_media_type_copper
) {
155 mac
->ops
.setup_link
= &ixgbe_setup_copper_link_82598
;
156 mac
->ops
.get_link_capabilities
=
157 &ixgbe_get_copper_link_capabilities_generic
;
160 switch (hw
->phy
.type
) {
162 phy
->ops
.setup_link
= &ixgbe_setup_phy_link_tnx
;
163 phy
->ops
.check_link
= &ixgbe_check_phy_link_tnx
;
164 phy
->ops
.get_firmware_version
=
165 &ixgbe_get_phy_firmware_version_tnx
;
168 phy
->ops
.reset
= &ixgbe_reset_phy_nl
;
170 /* Call SFP+ identify routine to get the SFP+ module type */
171 ret_val
= phy
->ops
.identify_sfp(hw
);
174 else if (hw
->phy
.sfp_type
== ixgbe_sfp_type_unknown
) {
175 ret_val
= IXGBE_ERR_SFP_NOT_SUPPORTED
;
179 /* Check to see if SFP+ module is supported */
180 ret_val
= ixgbe_get_sfp_init_sequence_offsets(hw
,
184 ret_val
= IXGBE_ERR_SFP_NOT_SUPPORTED
;
197 * ixgbe_start_hw_82598 - Prepare hardware for Tx/Rx
198 * @hw: pointer to hardware structure
200 * Starts the hardware using the generic start_hw function.
201 * Disables relaxed ordering Then set pcie completion timeout
204 static s32
ixgbe_start_hw_82598(struct ixgbe_hw
*hw
)
210 ret_val
= ixgbe_start_hw_generic(hw
);
212 /* Disable relaxed ordering */
213 for (i
= 0; ((i
< hw
->mac
.max_tx_queues
) &&
214 (i
< IXGBE_DCA_MAX_QUEUES_82598
)); i
++) {
215 regval
= IXGBE_READ_REG(hw
, IXGBE_DCA_TXCTRL(i
));
216 regval
&= ~IXGBE_DCA_TXCTRL_TX_WB_RO_EN
;
217 IXGBE_WRITE_REG(hw
, IXGBE_DCA_TXCTRL(i
), regval
);
220 for (i
= 0; ((i
< hw
->mac
.max_rx_queues
) &&
221 (i
< IXGBE_DCA_MAX_QUEUES_82598
)); i
++) {
222 regval
= IXGBE_READ_REG(hw
, IXGBE_DCA_RXCTRL(i
));
223 regval
&= ~(IXGBE_DCA_RXCTRL_DESC_WRO_EN
|
224 IXGBE_DCA_RXCTRL_DESC_HSRO_EN
);
225 IXGBE_WRITE_REG(hw
, IXGBE_DCA_RXCTRL(i
), regval
);
228 hw
->mac
.rx_pb_size
= IXGBE_82598_RX_PB_SIZE
;
230 /* set the completion timeout for interface */
232 ixgbe_set_pcie_completion_timeout(hw
);
238 * ixgbe_get_link_capabilities_82598 - Determines link capabilities
239 * @hw: pointer to hardware structure
240 * @speed: pointer to link speed
241 * @autoneg: boolean auto-negotiation value
243 * Determines the link capabilities by reading the AUTOC register.
245 static s32
ixgbe_get_link_capabilities_82598(struct ixgbe_hw
*hw
,
246 ixgbe_link_speed
*speed
,
253 * Determine link capabilities based on the stored value of AUTOC,
254 * which represents EEPROM defaults. If AUTOC value has not been
255 * stored, use the current register value.
257 if (hw
->mac
.orig_link_settings_stored
)
258 autoc
= hw
->mac
.orig_autoc
;
260 autoc
= IXGBE_READ_REG(hw
, IXGBE_AUTOC
);
262 switch (autoc
& IXGBE_AUTOC_LMS_MASK
) {
263 case IXGBE_AUTOC_LMS_1G_LINK_NO_AN
:
264 *speed
= IXGBE_LINK_SPEED_1GB_FULL
;
268 case IXGBE_AUTOC_LMS_10G_LINK_NO_AN
:
269 *speed
= IXGBE_LINK_SPEED_10GB_FULL
;
273 case IXGBE_AUTOC_LMS_1G_AN
:
274 *speed
= IXGBE_LINK_SPEED_1GB_FULL
;
278 case IXGBE_AUTOC_LMS_KX4_AN
:
279 case IXGBE_AUTOC_LMS_KX4_AN_1G_AN
:
280 *speed
= IXGBE_LINK_SPEED_UNKNOWN
;
281 if (autoc
& IXGBE_AUTOC_KX4_SUPP
)
282 *speed
|= IXGBE_LINK_SPEED_10GB_FULL
;
283 if (autoc
& IXGBE_AUTOC_KX_SUPP
)
284 *speed
|= IXGBE_LINK_SPEED_1GB_FULL
;
289 status
= IXGBE_ERR_LINK_SETUP
;
297 * ixgbe_get_media_type_82598 - Determines media type
298 * @hw: pointer to hardware structure
300 * Returns the media type (fiber, copper, backplane)
302 static enum ixgbe_media_type
ixgbe_get_media_type_82598(struct ixgbe_hw
*hw
)
304 enum ixgbe_media_type media_type
;
306 /* Detect if there is a copper PHY attached. */
307 switch (hw
->phy
.type
) {
308 case ixgbe_phy_cu_unknown
:
311 media_type
= ixgbe_media_type_copper
;
317 /* Media type for I82598 is based on device ID */
318 switch (hw
->device_id
) {
319 case IXGBE_DEV_ID_82598
:
320 case IXGBE_DEV_ID_82598_BX
:
321 /* Default device ID is mezzanine card KX/KX4 */
322 media_type
= ixgbe_media_type_backplane
;
324 case IXGBE_DEV_ID_82598AF_DUAL_PORT
:
325 case IXGBE_DEV_ID_82598AF_SINGLE_PORT
:
326 case IXGBE_DEV_ID_82598_DA_DUAL_PORT
:
327 case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM
:
328 case IXGBE_DEV_ID_82598EB_XF_LR
:
329 case IXGBE_DEV_ID_82598EB_SFP_LOM
:
330 media_type
= ixgbe_media_type_fiber
;
332 case IXGBE_DEV_ID_82598EB_CX4
:
333 case IXGBE_DEV_ID_82598_CX4_DUAL_PORT
:
334 media_type
= ixgbe_media_type_cx4
;
336 case IXGBE_DEV_ID_82598AT
:
337 case IXGBE_DEV_ID_82598AT2
:
338 media_type
= ixgbe_media_type_copper
;
341 media_type
= ixgbe_media_type_unknown
;
349 * ixgbe_fc_enable_82598 - Enable flow control
350 * @hw: pointer to hardware structure
351 * @packetbuf_num: packet buffer number (0-7)
353 * Enable flow control according to the current settings.
355 static s32
ixgbe_fc_enable_82598(struct ixgbe_hw
*hw
, s32 packetbuf_num
)
366 if (hw
->fc
.requested_mode
== ixgbe_fc_pfc
)
369 #endif /* CONFIG_DCB */
371 * On 82598 having Rx FC on causes resets while doing 1G
372 * so if it's on turn it off once we know link_speed. For
373 * more details see 82598 Specification update.
375 hw
->mac
.ops
.check_link(hw
, &link_speed
, &link_up
, false);
376 if (link_up
&& link_speed
== IXGBE_LINK_SPEED_1GB_FULL
) {
377 switch (hw
->fc
.requested_mode
) {
379 hw
->fc
.requested_mode
= ixgbe_fc_tx_pause
;
381 case ixgbe_fc_rx_pause
:
382 hw
->fc
.requested_mode
= ixgbe_fc_none
;
390 /* Negotiate the fc mode to use */
391 ret_val
= ixgbe_fc_autoneg(hw
);
392 if (ret_val
== IXGBE_ERR_FLOW_CONTROL
)
395 /* Disable any previous flow control settings */
396 fctrl_reg
= IXGBE_READ_REG(hw
, IXGBE_FCTRL
);
397 fctrl_reg
&= ~(IXGBE_FCTRL_RFCE
| IXGBE_FCTRL_RPFCE
);
399 rmcs_reg
= IXGBE_READ_REG(hw
, IXGBE_RMCS
);
400 rmcs_reg
&= ~(IXGBE_RMCS_TFCE_PRIORITY
| IXGBE_RMCS_TFCE_802_3X
);
403 * The possible values of fc.current_mode are:
404 * 0: Flow control is completely disabled
405 * 1: Rx flow control is enabled (we can receive pause frames,
406 * but not send pause frames).
407 * 2: Tx flow control is enabled (we can send pause frames but
408 * we do not support receiving pause frames).
409 * 3: Both Rx and Tx flow control (symmetric) are enabled.
411 * 4: Priority Flow Control is enabled.
415 switch (hw
->fc
.current_mode
) {
418 * Flow control is disabled by software override or autoneg.
419 * The code below will actually disable it in the HW.
422 case ixgbe_fc_rx_pause
:
424 * Rx Flow control is enabled and Tx Flow control is
425 * disabled by software override. Since there really
426 * isn't a way to advertise that we are capable of RX
427 * Pause ONLY, we will advertise that we support both
428 * symmetric and asymmetric Rx PAUSE. Later, we will
429 * disable the adapter's ability to send PAUSE frames.
431 fctrl_reg
|= IXGBE_FCTRL_RFCE
;
433 case ixgbe_fc_tx_pause
:
435 * Tx Flow control is enabled, and Rx Flow control is
436 * disabled by software override.
438 rmcs_reg
|= IXGBE_RMCS_TFCE_802_3X
;
441 /* Flow control (both Rx and Tx) is enabled by SW override. */
442 fctrl_reg
|= IXGBE_FCTRL_RFCE
;
443 rmcs_reg
|= IXGBE_RMCS_TFCE_802_3X
;
449 #endif /* CONFIG_DCB */
451 hw_dbg(hw
, "Flow control param set incorrectly\n");
452 ret_val
= IXGBE_ERR_CONFIG
;
457 /* Set 802.3x based flow control settings. */
458 fctrl_reg
|= IXGBE_FCTRL_DPF
;
459 IXGBE_WRITE_REG(hw
, IXGBE_FCTRL
, fctrl_reg
);
460 IXGBE_WRITE_REG(hw
, IXGBE_RMCS
, rmcs_reg
);
462 /* Set up and enable Rx high/low water mark thresholds, enable XON. */
463 if (hw
->fc
.current_mode
& ixgbe_fc_tx_pause
) {
464 rx_pba_size
= IXGBE_READ_REG(hw
, IXGBE_RXPBSIZE(packetbuf_num
));
465 rx_pba_size
>>= IXGBE_RXPBSIZE_SHIFT
;
467 reg
= (rx_pba_size
- hw
->fc
.low_water
) << 6;
469 reg
|= IXGBE_FCRTL_XONE
;
471 IXGBE_WRITE_REG(hw
, IXGBE_FCRTL(packetbuf_num
), reg
);
473 reg
= (rx_pba_size
- hw
->fc
.high_water
) << 6;
474 reg
|= IXGBE_FCRTH_FCEN
;
476 IXGBE_WRITE_REG(hw
, IXGBE_FCRTH(packetbuf_num
), reg
);
479 /* Configure pause time (2 TCs per register) */
480 reg
= IXGBE_READ_REG(hw
, IXGBE_FCTTV(packetbuf_num
/ 2));
481 if ((packetbuf_num
& 1) == 0)
482 reg
= (reg
& 0xFFFF0000) | hw
->fc
.pause_time
;
484 reg
= (reg
& 0x0000FFFF) | (hw
->fc
.pause_time
<< 16);
485 IXGBE_WRITE_REG(hw
, IXGBE_FCTTV(packetbuf_num
/ 2), reg
);
487 IXGBE_WRITE_REG(hw
, IXGBE_FCRTV
, (hw
->fc
.pause_time
>> 1));
494 * ixgbe_start_mac_link_82598 - Configures MAC link settings
495 * @hw: pointer to hardware structure
497 * Configures link settings based on values in the ixgbe_hw struct.
498 * Restarts the link. Performs autonegotiation if needed.
500 static s32
ixgbe_start_mac_link_82598(struct ixgbe_hw
*hw
,
501 bool autoneg_wait_to_complete
)
509 autoc_reg
= IXGBE_READ_REG(hw
, IXGBE_AUTOC
);
510 autoc_reg
|= IXGBE_AUTOC_AN_RESTART
;
511 IXGBE_WRITE_REG(hw
, IXGBE_AUTOC
, autoc_reg
);
513 /* Only poll for autoneg to complete if specified to do so */
514 if (autoneg_wait_to_complete
) {
515 if ((autoc_reg
& IXGBE_AUTOC_LMS_MASK
) ==
516 IXGBE_AUTOC_LMS_KX4_AN
||
517 (autoc_reg
& IXGBE_AUTOC_LMS_MASK
) ==
518 IXGBE_AUTOC_LMS_KX4_AN_1G_AN
) {
519 links_reg
= 0; /* Just in case Autoneg time = 0 */
520 for (i
= 0; i
< IXGBE_AUTO_NEG_TIME
; i
++) {
521 links_reg
= IXGBE_READ_REG(hw
, IXGBE_LINKS
);
522 if (links_reg
& IXGBE_LINKS_KX_AN_COMP
)
526 if (!(links_reg
& IXGBE_LINKS_KX_AN_COMP
)) {
527 status
= IXGBE_ERR_AUTONEG_NOT_COMPLETE
;
528 hw_dbg(hw
, "Autonegotiation did not complete.\n");
533 /* Add delay to filter out noises during initial link setup */
540 * ixgbe_validate_link_ready - Function looks for phy link
541 * @hw: pointer to hardware structure
543 * Function indicates success when phy link is available. If phy is not ready
544 * within 5 seconds of MAC indicating link, the function returns error.
546 static s32
ixgbe_validate_link_ready(struct ixgbe_hw
*hw
)
551 if (hw
->device_id
!= IXGBE_DEV_ID_82598AT2
)
555 timeout
< IXGBE_VALIDATE_LINK_READY_TIMEOUT
; timeout
++) {
556 hw
->phy
.ops
.read_reg(hw
, MDIO_STAT1
, MDIO_MMD_AN
, &an_reg
);
558 if ((an_reg
& MDIO_AN_STAT1_COMPLETE
) &&
559 (an_reg
& MDIO_STAT1_LSTATUS
))
565 if (timeout
== IXGBE_VALIDATE_LINK_READY_TIMEOUT
) {
566 hw_dbg(hw
, "Link was indicated but link is down\n");
567 return IXGBE_ERR_LINK_SETUP
;
574 * ixgbe_check_mac_link_82598 - Get link/speed status
575 * @hw: pointer to hardware structure
576 * @speed: pointer to link speed
577 * @link_up: true is link is up, false otherwise
578 * @link_up_wait_to_complete: bool used to wait for link up or not
580 * Reads the links register to determine if link is up and the current speed
582 static s32
ixgbe_check_mac_link_82598(struct ixgbe_hw
*hw
,
583 ixgbe_link_speed
*speed
, bool *link_up
,
584 bool link_up_wait_to_complete
)
588 u16 link_reg
, adapt_comp_reg
;
591 * SERDES PHY requires us to read link status from register 0xC79F.
592 * Bit 0 set indicates link is up/ready; clear indicates link down.
593 * 0xC00C is read to check that the XAUI lanes are active. Bit 0
594 * clear indicates active; set indicates inactive.
596 if (hw
->phy
.type
== ixgbe_phy_nl
) {
597 hw
->phy
.ops
.read_reg(hw
, 0xC79F, MDIO_MMD_PMAPMD
, &link_reg
);
598 hw
->phy
.ops
.read_reg(hw
, 0xC79F, MDIO_MMD_PMAPMD
, &link_reg
);
599 hw
->phy
.ops
.read_reg(hw
, 0xC00C, MDIO_MMD_PMAPMD
,
601 if (link_up_wait_to_complete
) {
602 for (i
= 0; i
< IXGBE_LINK_UP_TIME
; i
++) {
603 if ((link_reg
& 1) &&
604 ((adapt_comp_reg
& 1) == 0)) {
611 hw
->phy
.ops
.read_reg(hw
, 0xC79F,
614 hw
->phy
.ops
.read_reg(hw
, 0xC00C,
619 if ((link_reg
& 1) && ((adapt_comp_reg
& 1) == 0))
625 if (*link_up
== false)
629 links_reg
= IXGBE_READ_REG(hw
, IXGBE_LINKS
);
630 if (link_up_wait_to_complete
) {
631 for (i
= 0; i
< IXGBE_LINK_UP_TIME
; i
++) {
632 if (links_reg
& IXGBE_LINKS_UP
) {
639 links_reg
= IXGBE_READ_REG(hw
, IXGBE_LINKS
);
642 if (links_reg
& IXGBE_LINKS_UP
)
648 if (links_reg
& IXGBE_LINKS_SPEED
)
649 *speed
= IXGBE_LINK_SPEED_10GB_FULL
;
651 *speed
= IXGBE_LINK_SPEED_1GB_FULL
;
653 if ((hw
->device_id
== IXGBE_DEV_ID_82598AT2
) && (*link_up
== true) &&
654 (ixgbe_validate_link_ready(hw
) != 0))
657 /* if link is down, zero out the current_mode */
658 if (*link_up
== false) {
659 hw
->fc
.current_mode
= ixgbe_fc_none
;
660 hw
->fc
.fc_was_autonegged
= false;
667 * ixgbe_setup_mac_link_82598 - Set MAC link speed
668 * @hw: pointer to hardware structure
669 * @speed: new link speed
670 * @autoneg: true if auto-negotiation enabled
671 * @autoneg_wait_to_complete: true when waiting for completion is needed
673 * Set the link speed in the AUTOC register and restarts link.
675 static s32
ixgbe_setup_mac_link_82598(struct ixgbe_hw
*hw
,
676 ixgbe_link_speed speed
, bool autoneg
,
677 bool autoneg_wait_to_complete
)
680 ixgbe_link_speed link_capabilities
= IXGBE_LINK_SPEED_UNKNOWN
;
681 u32 curr_autoc
= IXGBE_READ_REG(hw
, IXGBE_AUTOC
);
682 u32 autoc
= curr_autoc
;
683 u32 link_mode
= autoc
& IXGBE_AUTOC_LMS_MASK
;
685 /* Check to see if speed passed in is supported. */
686 ixgbe_get_link_capabilities_82598(hw
, &link_capabilities
, &autoneg
);
687 speed
&= link_capabilities
;
689 if (speed
== IXGBE_LINK_SPEED_UNKNOWN
)
690 status
= IXGBE_ERR_LINK_SETUP
;
692 /* Set KX4/KX support according to speed requested */
693 else if (link_mode
== IXGBE_AUTOC_LMS_KX4_AN
||
694 link_mode
== IXGBE_AUTOC_LMS_KX4_AN_1G_AN
) {
695 autoc
&= ~IXGBE_AUTOC_KX4_KX_SUPP_MASK
;
696 if (speed
& IXGBE_LINK_SPEED_10GB_FULL
)
697 autoc
|= IXGBE_AUTOC_KX4_SUPP
;
698 if (speed
& IXGBE_LINK_SPEED_1GB_FULL
)
699 autoc
|= IXGBE_AUTOC_KX_SUPP
;
700 if (autoc
!= curr_autoc
)
701 IXGBE_WRITE_REG(hw
, IXGBE_AUTOC
, autoc
);
706 * Setup and restart the link based on the new values in
707 * ixgbe_hw This will write the AUTOC register based on the new
710 status
= ixgbe_start_mac_link_82598(hw
,
711 autoneg_wait_to_complete
);
719 * ixgbe_setup_copper_link_82598 - Set the PHY autoneg advertised field
720 * @hw: pointer to hardware structure
721 * @speed: new link speed
722 * @autoneg: true if autonegotiation enabled
723 * @autoneg_wait_to_complete: true if waiting is needed to complete
725 * Sets the link speed in the AUTOC register in the MAC and restarts link.
727 static s32
ixgbe_setup_copper_link_82598(struct ixgbe_hw
*hw
,
728 ixgbe_link_speed speed
,
730 bool autoneg_wait_to_complete
)
734 /* Setup the PHY according to input speed */
735 status
= hw
->phy
.ops
.setup_link_speed(hw
, speed
, autoneg
,
736 autoneg_wait_to_complete
);
738 ixgbe_start_mac_link_82598(hw
, autoneg_wait_to_complete
);
744 * ixgbe_reset_hw_82598 - Performs hardware reset
745 * @hw: pointer to hardware structure
747 * Resets the hardware by resetting the transmit and receive units, masks and
748 * clears all interrupts, performing a PHY reset, and performing a link (MAC)
751 static s32
ixgbe_reset_hw_82598(struct ixgbe_hw
*hw
)
761 /* Call adapter stop to disable tx/rx and clear interrupts */
762 hw
->mac
.ops
.stop_adapter(hw
);
765 * Power up the Atlas Tx lanes if they are currently powered down.
766 * Atlas Tx lanes are powered down for MAC loopback tests, but
767 * they are not automatically restored on reset.
769 hw
->mac
.ops
.read_analog_reg8(hw
, IXGBE_ATLAS_PDN_LPBK
, &analog_val
);
770 if (analog_val
& IXGBE_ATLAS_PDN_TX_REG_EN
) {
771 /* Enable Tx Atlas so packets can be transmitted again */
772 hw
->mac
.ops
.read_analog_reg8(hw
, IXGBE_ATLAS_PDN_LPBK
,
774 analog_val
&= ~IXGBE_ATLAS_PDN_TX_REG_EN
;
775 hw
->mac
.ops
.write_analog_reg8(hw
, IXGBE_ATLAS_PDN_LPBK
,
778 hw
->mac
.ops
.read_analog_reg8(hw
, IXGBE_ATLAS_PDN_10G
,
780 analog_val
&= ~IXGBE_ATLAS_PDN_TX_10G_QL_ALL
;
781 hw
->mac
.ops
.write_analog_reg8(hw
, IXGBE_ATLAS_PDN_10G
,
784 hw
->mac
.ops
.read_analog_reg8(hw
, IXGBE_ATLAS_PDN_1G
,
786 analog_val
&= ~IXGBE_ATLAS_PDN_TX_1G_QL_ALL
;
787 hw
->mac
.ops
.write_analog_reg8(hw
, IXGBE_ATLAS_PDN_1G
,
790 hw
->mac
.ops
.read_analog_reg8(hw
, IXGBE_ATLAS_PDN_AN
,
792 analog_val
&= ~IXGBE_ATLAS_PDN_TX_AN_QL_ALL
;
793 hw
->mac
.ops
.write_analog_reg8(hw
, IXGBE_ATLAS_PDN_AN
,
798 if (hw
->phy
.reset_disable
== false) {
799 /* PHY ops must be identified and initialized prior to reset */
801 /* Init PHY and function pointers, perform SFP setup */
802 phy_status
= hw
->phy
.ops
.init(hw
);
803 if (phy_status
== IXGBE_ERR_SFP_NOT_SUPPORTED
)
805 else if (phy_status
== IXGBE_ERR_SFP_NOT_PRESENT
)
808 hw
->phy
.ops
.reset(hw
);
813 * Prevent the PCI-E bus from from hanging by disabling PCI-E master
814 * access and verify no pending requests before reset
816 ixgbe_disable_pcie_master(hw
);
820 * Issue global reset to the MAC. This needs to be a SW reset.
821 * If link reset is used, it might reset the MAC when mng is using it
823 ctrl
= IXGBE_READ_REG(hw
, IXGBE_CTRL
);
824 IXGBE_WRITE_REG(hw
, IXGBE_CTRL
, (ctrl
| IXGBE_CTRL_RST
));
825 IXGBE_WRITE_FLUSH(hw
);
827 /* Poll for reset bit to self-clear indicating reset is complete */
828 for (i
= 0; i
< 10; i
++) {
830 ctrl
= IXGBE_READ_REG(hw
, IXGBE_CTRL
);
831 if (!(ctrl
& IXGBE_CTRL_RST
))
834 if (ctrl
& IXGBE_CTRL_RST
) {
835 status
= IXGBE_ERR_RESET_FAILED
;
836 hw_dbg(hw
, "Reset polling failed to complete.\n");
840 * Double resets are required for recovery from certain error
841 * conditions. Between resets, it is necessary to stall to allow time
842 * for any pending HW events to complete. We use 1usec since that is
843 * what is needed for ixgbe_disable_pcie_master(). The second reset
844 * then clears out any effects of those events.
846 if (hw
->mac
.flags
& IXGBE_FLAGS_DOUBLE_RESET_REQUIRED
) {
847 hw
->mac
.flags
&= ~IXGBE_FLAGS_DOUBLE_RESET_REQUIRED
;
854 gheccr
= IXGBE_READ_REG(hw
, IXGBE_GHECCR
);
855 gheccr
&= ~((1 << 21) | (1 << 18) | (1 << 9) | (1 << 6));
856 IXGBE_WRITE_REG(hw
, IXGBE_GHECCR
, gheccr
);
859 * Store the original AUTOC value if it has not been
860 * stored off yet. Otherwise restore the stored original
861 * AUTOC value since the reset operation sets back to deaults.
863 autoc
= IXGBE_READ_REG(hw
, IXGBE_AUTOC
);
864 if (hw
->mac
.orig_link_settings_stored
== false) {
865 hw
->mac
.orig_autoc
= autoc
;
866 hw
->mac
.orig_link_settings_stored
= true;
867 } else if (autoc
!= hw
->mac
.orig_autoc
) {
868 IXGBE_WRITE_REG(hw
, IXGBE_AUTOC
, hw
->mac
.orig_autoc
);
871 /* Store the permanent mac address */
872 hw
->mac
.ops
.get_mac_addr(hw
, hw
->mac
.perm_addr
);
875 * Store MAC address from RAR0, clear receive address registers, and
876 * clear the multicast table
878 hw
->mac
.ops
.init_rx_addrs(hw
);
888 * ixgbe_set_vmdq_82598 - Associate a VMDq set index with a rx address
889 * @hw: pointer to hardware struct
890 * @rar: receive address register index to associate with a VMDq index
891 * @vmdq: VMDq set index
893 static s32
ixgbe_set_vmdq_82598(struct ixgbe_hw
*hw
, u32 rar
, u32 vmdq
)
896 u32 rar_entries
= hw
->mac
.num_rar_entries
;
898 /* Make sure we are using a valid rar index range */
899 if (rar
>= rar_entries
) {
900 hw_dbg(hw
, "RAR index %d is out of range.\n", rar
);
901 return IXGBE_ERR_INVALID_ARGUMENT
;
904 rar_high
= IXGBE_READ_REG(hw
, IXGBE_RAH(rar
));
905 rar_high
&= ~IXGBE_RAH_VIND_MASK
;
906 rar_high
|= ((vmdq
<< IXGBE_RAH_VIND_SHIFT
) & IXGBE_RAH_VIND_MASK
);
907 IXGBE_WRITE_REG(hw
, IXGBE_RAH(rar
), rar_high
);
912 * ixgbe_clear_vmdq_82598 - Disassociate a VMDq set index from an rx address
913 * @hw: pointer to hardware struct
914 * @rar: receive address register index to associate with a VMDq index
915 * @vmdq: VMDq clear index (not used in 82598, but elsewhere)
917 static s32
ixgbe_clear_vmdq_82598(struct ixgbe_hw
*hw
, u32 rar
, u32 vmdq
)
920 u32 rar_entries
= hw
->mac
.num_rar_entries
;
923 /* Make sure we are using a valid rar index range */
924 if (rar
>= rar_entries
) {
925 hw_dbg(hw
, "RAR index %d is out of range.\n", rar
);
926 return IXGBE_ERR_INVALID_ARGUMENT
;
929 rar_high
= IXGBE_READ_REG(hw
, IXGBE_RAH(rar
));
930 if (rar_high
& IXGBE_RAH_VIND_MASK
) {
931 rar_high
&= ~IXGBE_RAH_VIND_MASK
;
932 IXGBE_WRITE_REG(hw
, IXGBE_RAH(rar
), rar_high
);
939 * ixgbe_set_vfta_82598 - Set VLAN filter table
940 * @hw: pointer to hardware structure
941 * @vlan: VLAN id to write to VLAN filter
942 * @vind: VMDq output index that maps queue to VLAN id in VFTA
943 * @vlan_on: boolean flag to turn on/off VLAN in VFTA
945 * Turn on/off specified VLAN in the VLAN filter table.
947 static s32
ixgbe_set_vfta_82598(struct ixgbe_hw
*hw
, u32 vlan
, u32 vind
,
956 return IXGBE_ERR_PARAM
;
958 /* Determine 32-bit word position in array */
959 regindex
= (vlan
>> 5) & 0x7F; /* upper seven bits */
961 /* Determine the location of the (VMD) queue index */
962 vftabyte
= ((vlan
>> 3) & 0x03); /* bits (4:3) indicating byte array */
963 bitindex
= (vlan
& 0x7) << 2; /* lower 3 bits indicate nibble */
965 /* Set the nibble for VMD queue index */
966 bits
= IXGBE_READ_REG(hw
, IXGBE_VFTAVIND(vftabyte
, regindex
));
967 bits
&= (~(0x0F << bitindex
));
968 bits
|= (vind
<< bitindex
);
969 IXGBE_WRITE_REG(hw
, IXGBE_VFTAVIND(vftabyte
, regindex
), bits
);
971 /* Determine the location of the bit for this VLAN id */
972 bitindex
= vlan
& 0x1F; /* lower five bits */
974 bits
= IXGBE_READ_REG(hw
, IXGBE_VFTA(regindex
));
976 /* Turn on this VLAN id */
977 bits
|= (1 << bitindex
);
979 /* Turn off this VLAN id */
980 bits
&= ~(1 << bitindex
);
981 IXGBE_WRITE_REG(hw
, IXGBE_VFTA(regindex
), bits
);
987 * ixgbe_clear_vfta_82598 - Clear VLAN filter table
988 * @hw: pointer to hardware structure
990 * Clears the VLAN filer table, and the VMDq index associated with the filter
992 static s32
ixgbe_clear_vfta_82598(struct ixgbe_hw
*hw
)
997 for (offset
= 0; offset
< hw
->mac
.vft_size
; offset
++)
998 IXGBE_WRITE_REG(hw
, IXGBE_VFTA(offset
), 0);
1000 for (vlanbyte
= 0; vlanbyte
< 4; vlanbyte
++)
1001 for (offset
= 0; offset
< hw
->mac
.vft_size
; offset
++)
1002 IXGBE_WRITE_REG(hw
, IXGBE_VFTAVIND(vlanbyte
, offset
),
1009 * ixgbe_read_analog_reg8_82598 - Reads 8 bit Atlas analog register
1010 * @hw: pointer to hardware structure
1011 * @reg: analog register to read
1014 * Performs read operation to Atlas analog register specified.
1016 static s32
ixgbe_read_analog_reg8_82598(struct ixgbe_hw
*hw
, u32 reg
, u8
*val
)
1020 IXGBE_WRITE_REG(hw
, IXGBE_ATLASCTL
,
1021 IXGBE_ATLASCTL_WRITE_CMD
| (reg
<< 8));
1022 IXGBE_WRITE_FLUSH(hw
);
1024 atlas_ctl
= IXGBE_READ_REG(hw
, IXGBE_ATLASCTL
);
1025 *val
= (u8
)atlas_ctl
;
1031 * ixgbe_write_analog_reg8_82598 - Writes 8 bit Atlas analog register
1032 * @hw: pointer to hardware structure
1033 * @reg: atlas register to write
1034 * @val: value to write
1036 * Performs write operation to Atlas analog register specified.
1038 static s32
ixgbe_write_analog_reg8_82598(struct ixgbe_hw
*hw
, u32 reg
, u8 val
)
1042 atlas_ctl
= (reg
<< 8) | val
;
1043 IXGBE_WRITE_REG(hw
, IXGBE_ATLASCTL
, atlas_ctl
);
1044 IXGBE_WRITE_FLUSH(hw
);
1051 * ixgbe_read_i2c_eeprom_82598 - Reads 8 bit word over I2C interface.
1052 * @hw: pointer to hardware structure
1053 * @byte_offset: EEPROM byte offset to read
1054 * @eeprom_data: value read
1056 * Performs 8 byte read operation to SFP module's EEPROM over I2C interface.
1058 static s32
ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw
*hw
, u8 byte_offset
,
1067 if (hw
->phy
.type
== ixgbe_phy_nl
) {
1069 * phy SDA/SCL registers are at addresses 0xC30A to
1070 * 0xC30D. These registers are used to talk to the SFP+
1071 * module's EEPROM through the SDA/SCL (I2C) interface.
1073 sfp_addr
= (IXGBE_I2C_EEPROM_DEV_ADDR
<< 8) + byte_offset
;
1074 sfp_addr
= (sfp_addr
| IXGBE_I2C_EEPROM_READ_MASK
);
1075 hw
->phy
.ops
.write_reg(hw
,
1076 IXGBE_MDIO_PMA_PMD_SDA_SCL_ADDR
,
1081 for (i
= 0; i
< 100; i
++) {
1082 hw
->phy
.ops
.read_reg(hw
,
1083 IXGBE_MDIO_PMA_PMD_SDA_SCL_STAT
,
1086 sfp_stat
= sfp_stat
& IXGBE_I2C_EEPROM_STATUS_MASK
;
1087 if (sfp_stat
!= IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS
)
1089 usleep_range(10000, 20000);
1092 if (sfp_stat
!= IXGBE_I2C_EEPROM_STATUS_PASS
) {
1093 hw_dbg(hw
, "EEPROM read did not pass.\n");
1094 status
= IXGBE_ERR_SFP_NOT_PRESENT
;
1099 hw
->phy
.ops
.read_reg(hw
, IXGBE_MDIO_PMA_PMD_SDA_SCL_DATA
,
1100 MDIO_MMD_PMAPMD
, &sfp_data
);
1102 *eeprom_data
= (u8
)(sfp_data
>> 8);
1104 status
= IXGBE_ERR_PHY
;
1113 * ixgbe_get_supported_physical_layer_82598 - Returns physical layer type
1114 * @hw: pointer to hardware structure
1116 * Determines physical layer capabilities of the current configuration.
1118 static u32
ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw
*hw
)
1120 u32 physical_layer
= IXGBE_PHYSICAL_LAYER_UNKNOWN
;
1121 u32 autoc
= IXGBE_READ_REG(hw
, IXGBE_AUTOC
);
1122 u32 pma_pmd_10g
= autoc
& IXGBE_AUTOC_10G_PMA_PMD_MASK
;
1123 u32 pma_pmd_1g
= autoc
& IXGBE_AUTOC_1G_PMA_PMD_MASK
;
1124 u16 ext_ability
= 0;
1126 hw
->phy
.ops
.identify(hw
);
1128 /* Copper PHY must be checked before AUTOC LMS to determine correct
1129 * physical layer because 10GBase-T PHYs use LMS = KX4/KX */
1130 switch (hw
->phy
.type
) {
1133 case ixgbe_phy_cu_unknown
:
1134 hw
->phy
.ops
.read_reg(hw
, MDIO_PMA_EXTABLE
,
1135 MDIO_MMD_PMAPMD
, &ext_ability
);
1136 if (ext_ability
& MDIO_PMA_EXTABLE_10GBT
)
1137 physical_layer
|= IXGBE_PHYSICAL_LAYER_10GBASE_T
;
1138 if (ext_ability
& MDIO_PMA_EXTABLE_1000BT
)
1139 physical_layer
|= IXGBE_PHYSICAL_LAYER_1000BASE_T
;
1140 if (ext_ability
& MDIO_PMA_EXTABLE_100BTX
)
1141 physical_layer
|= IXGBE_PHYSICAL_LAYER_100BASE_TX
;
1147 switch (autoc
& IXGBE_AUTOC_LMS_MASK
) {
1148 case IXGBE_AUTOC_LMS_1G_AN
:
1149 case IXGBE_AUTOC_LMS_1G_LINK_NO_AN
:
1150 if (pma_pmd_1g
== IXGBE_AUTOC_1G_KX
)
1151 physical_layer
= IXGBE_PHYSICAL_LAYER_1000BASE_KX
;
1153 physical_layer
= IXGBE_PHYSICAL_LAYER_1000BASE_BX
;
1155 case IXGBE_AUTOC_LMS_10G_LINK_NO_AN
:
1156 if (pma_pmd_10g
== IXGBE_AUTOC_10G_CX4
)
1157 physical_layer
= IXGBE_PHYSICAL_LAYER_10GBASE_CX4
;
1158 else if (pma_pmd_10g
== IXGBE_AUTOC_10G_KX4
)
1159 physical_layer
= IXGBE_PHYSICAL_LAYER_10GBASE_KX4
;
1161 physical_layer
= IXGBE_PHYSICAL_LAYER_UNKNOWN
;
1163 case IXGBE_AUTOC_LMS_KX4_AN
:
1164 case IXGBE_AUTOC_LMS_KX4_AN_1G_AN
:
1165 if (autoc
& IXGBE_AUTOC_KX_SUPP
)
1166 physical_layer
|= IXGBE_PHYSICAL_LAYER_1000BASE_KX
;
1167 if (autoc
& IXGBE_AUTOC_KX4_SUPP
)
1168 physical_layer
|= IXGBE_PHYSICAL_LAYER_10GBASE_KX4
;
1174 if (hw
->phy
.type
== ixgbe_phy_nl
) {
1175 hw
->phy
.ops
.identify_sfp(hw
);
1177 switch (hw
->phy
.sfp_type
) {
1178 case ixgbe_sfp_type_da_cu
:
1179 physical_layer
= IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU
;
1181 case ixgbe_sfp_type_sr
:
1182 physical_layer
= IXGBE_PHYSICAL_LAYER_10GBASE_SR
;
1184 case ixgbe_sfp_type_lr
:
1185 physical_layer
= IXGBE_PHYSICAL_LAYER_10GBASE_LR
;
1188 physical_layer
= IXGBE_PHYSICAL_LAYER_UNKNOWN
;
1193 switch (hw
->device_id
) {
1194 case IXGBE_DEV_ID_82598_DA_DUAL_PORT
:
1195 physical_layer
= IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU
;
1197 case IXGBE_DEV_ID_82598AF_DUAL_PORT
:
1198 case IXGBE_DEV_ID_82598AF_SINGLE_PORT
:
1199 case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM
:
1200 physical_layer
= IXGBE_PHYSICAL_LAYER_10GBASE_SR
;
1202 case IXGBE_DEV_ID_82598EB_XF_LR
:
1203 physical_layer
= IXGBE_PHYSICAL_LAYER_10GBASE_LR
;
1210 return physical_layer
;
1214 * ixgbe_set_lan_id_multi_port_pcie_82598 - Set LAN id for PCIe multiple
1216 * @hw: pointer to the HW structure
1218 * Calls common function and corrects issue with some single port devices
1219 * that enable LAN1 but not LAN0.
1221 static void ixgbe_set_lan_id_multi_port_pcie_82598(struct ixgbe_hw
*hw
)
1223 struct ixgbe_bus_info
*bus
= &hw
->bus
;
1227 ixgbe_set_lan_id_multi_port_pcie(hw
);
1229 /* check if LAN0 is disabled */
1230 hw
->eeprom
.ops
.read(hw
, IXGBE_PCIE_GENERAL_PTR
, &pci_gen
);
1231 if ((pci_gen
!= 0) && (pci_gen
!= 0xFFFF)) {
1233 hw
->eeprom
.ops
.read(hw
, pci_gen
+ IXGBE_PCIE_CTRL2
, &pci_ctrl2
);
1235 /* if LAN0 is completely disabled force function to 0 */
1236 if ((pci_ctrl2
& IXGBE_PCIE_CTRL2_LAN_DISABLE
) &&
1237 !(pci_ctrl2
& IXGBE_PCIE_CTRL2_DISABLE_SELECT
) &&
1238 !(pci_ctrl2
& IXGBE_PCIE_CTRL2_DUMMY_ENABLE
)) {
1246 * ixgbe_set_rxpba_82598 - Configure packet buffers
1247 * @hw: pointer to hardware structure
1248 * @dcb_config: pointer to ixgbe_dcb_config structure
1250 * Configure packet buffers.
1252 static void ixgbe_set_rxpba_82598(struct ixgbe_hw
*hw
, int num_pb
, u32 headroom
,
1255 u32 rxpktsize
= IXGBE_RXPBSIZE_64KB
;
1261 /* Setup Rx packet buffer sizes */
1263 case PBA_STRATEGY_WEIGHTED
:
1264 /* Setup the first four at 80KB */
1265 rxpktsize
= IXGBE_RXPBSIZE_80KB
;
1267 IXGBE_WRITE_REG(hw
, IXGBE_RXPBSIZE(i
), rxpktsize
);
1268 /* Setup the last four at 48KB...don't re-init i */
1269 rxpktsize
= IXGBE_RXPBSIZE_48KB
;
1271 case PBA_STRATEGY_EQUAL
:
1273 /* Divide the remaining Rx packet buffer evenly among the TCs */
1274 for (; i
< IXGBE_MAX_PACKET_BUFFERS
; i
++)
1275 IXGBE_WRITE_REG(hw
, IXGBE_RXPBSIZE(i
), rxpktsize
);
1279 /* Setup Tx packet buffer sizes */
1280 for (i
= 0; i
< IXGBE_MAX_PACKET_BUFFERS
; i
++)
1281 IXGBE_WRITE_REG(hw
, IXGBE_TXPBSIZE(i
), IXGBE_TXPBSIZE_40KB
);
1286 static struct ixgbe_mac_operations mac_ops_82598
= {
1287 .init_hw
= &ixgbe_init_hw_generic
,
1288 .reset_hw
= &ixgbe_reset_hw_82598
,
1289 .start_hw
= &ixgbe_start_hw_82598
,
1290 .clear_hw_cntrs
= &ixgbe_clear_hw_cntrs_generic
,
1291 .get_media_type
= &ixgbe_get_media_type_82598
,
1292 .get_supported_physical_layer
= &ixgbe_get_supported_physical_layer_82598
,
1293 .enable_rx_dma
= &ixgbe_enable_rx_dma_generic
,
1294 .get_mac_addr
= &ixgbe_get_mac_addr_generic
,
1295 .stop_adapter
= &ixgbe_stop_adapter_generic
,
1296 .get_bus_info
= &ixgbe_get_bus_info_generic
,
1297 .set_lan_id
= &ixgbe_set_lan_id_multi_port_pcie_82598
,
1298 .read_analog_reg8
= &ixgbe_read_analog_reg8_82598
,
1299 .write_analog_reg8
= &ixgbe_write_analog_reg8_82598
,
1300 .setup_link
= &ixgbe_setup_mac_link_82598
,
1301 .set_rxpba
= &ixgbe_set_rxpba_82598
,
1302 .check_link
= &ixgbe_check_mac_link_82598
,
1303 .get_link_capabilities
= &ixgbe_get_link_capabilities_82598
,
1304 .led_on
= &ixgbe_led_on_generic
,
1305 .led_off
= &ixgbe_led_off_generic
,
1306 .blink_led_start
= &ixgbe_blink_led_start_generic
,
1307 .blink_led_stop
= &ixgbe_blink_led_stop_generic
,
1308 .set_rar
= &ixgbe_set_rar_generic
,
1309 .clear_rar
= &ixgbe_clear_rar_generic
,
1310 .set_vmdq
= &ixgbe_set_vmdq_82598
,
1311 .clear_vmdq
= &ixgbe_clear_vmdq_82598
,
1312 .init_rx_addrs
= &ixgbe_init_rx_addrs_generic
,
1313 .update_mc_addr_list
= &ixgbe_update_mc_addr_list_generic
,
1314 .enable_mc
= &ixgbe_enable_mc_generic
,
1315 .disable_mc
= &ixgbe_disable_mc_generic
,
1316 .clear_vfta
= &ixgbe_clear_vfta_82598
,
1317 .set_vfta
= &ixgbe_set_vfta_82598
,
1318 .fc_enable
= &ixgbe_fc_enable_82598
,
1319 .set_fw_drv_ver
= NULL
,
1320 .acquire_swfw_sync
= &ixgbe_acquire_swfw_sync
,
1321 .release_swfw_sync
= &ixgbe_release_swfw_sync
,
1324 static struct ixgbe_eeprom_operations eeprom_ops_82598
= {
1325 .init_params
= &ixgbe_init_eeprom_params_generic
,
1326 .read
= &ixgbe_read_eerd_generic
,
1327 .read_buffer
= &ixgbe_read_eerd_buffer_generic
,
1328 .calc_checksum
= &ixgbe_calc_eeprom_checksum_generic
,
1329 .validate_checksum
= &ixgbe_validate_eeprom_checksum_generic
,
1330 .update_checksum
= &ixgbe_update_eeprom_checksum_generic
,
1333 static struct ixgbe_phy_operations phy_ops_82598
= {
1334 .identify
= &ixgbe_identify_phy_generic
,
1335 .identify_sfp
= &ixgbe_identify_sfp_module_generic
,
1336 .init
= &ixgbe_init_phy_ops_82598
,
1337 .reset
= &ixgbe_reset_phy_generic
,
1338 .read_reg
= &ixgbe_read_phy_reg_generic
,
1339 .write_reg
= &ixgbe_write_phy_reg_generic
,
1340 .setup_link
= &ixgbe_setup_phy_link_generic
,
1341 .setup_link_speed
= &ixgbe_setup_phy_link_speed_generic
,
1342 .read_i2c_eeprom
= &ixgbe_read_i2c_eeprom_82598
,
1343 .check_overtemp
= &ixgbe_tn_check_overtemp
,
1346 struct ixgbe_info ixgbe_82598_info
= {
1347 .mac
= ixgbe_mac_82598EB
,
1348 .get_invariants
= &ixgbe_get_invariants_82598
,
1349 .mac_ops
= &mac_ops_82598
,
1350 .eeprom_ops
= &eeprom_ops_82598
,
1351 .phy_ops
= &phy_ops_82598
,