Merge remote-tracking branch 'cleancache/linux-next'
[linux-2.6/next.git] / drivers / mfd / sm501.c
blobdf3702c1756df9aae08dcfbbf1bde345d7520172
1 /* linux/drivers/mfd/sm501.c
3 * Copyright (C) 2006 Simtec Electronics
4 * Ben Dooks <ben@simtec.co.uk>
5 * Vincent Sanders <vince@simtec.co.uk>
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License version 2 as
9 * published by the Free Software Foundation.
11 * SM501 MFD driver
14 #include <linux/kernel.h>
15 #include <linux/module.h>
16 #include <linux/delay.h>
17 #include <linux/init.h>
18 #include <linux/list.h>
19 #include <linux/device.h>
20 #include <linux/platform_device.h>
21 #include <linux/pci.h>
22 #include <linux/i2c-gpio.h>
23 #include <linux/slab.h>
25 #include <linux/sm501.h>
26 #include <linux/sm501-regs.h>
27 #include <linux/serial_8250.h>
29 #include <linux/io.h>
31 struct sm501_device {
32 struct list_head list;
33 struct platform_device pdev;
36 struct sm501_gpio;
38 #ifdef CONFIG_MFD_SM501_GPIO
39 #include <linux/gpio.h>
41 struct sm501_gpio_chip {
42 struct gpio_chip gpio;
43 struct sm501_gpio *ourgpio; /* to get back to parent. */
44 void __iomem *regbase;
45 void __iomem *control; /* address of control reg. */
48 struct sm501_gpio {
49 struct sm501_gpio_chip low;
50 struct sm501_gpio_chip high;
51 spinlock_t lock;
53 unsigned int registered : 1;
54 void __iomem *regs;
55 struct resource *regs_res;
57 #else
58 struct sm501_gpio {
59 /* no gpio support, empty definition for sm501_devdata. */
61 #endif
63 struct sm501_devdata {
64 spinlock_t reg_lock;
65 struct mutex clock_lock;
66 struct list_head devices;
67 struct sm501_gpio gpio;
69 struct device *dev;
70 struct resource *io_res;
71 struct resource *mem_res;
72 struct resource *regs_claim;
73 struct sm501_platdata *platdata;
76 unsigned int in_suspend;
77 unsigned long pm_misc;
79 int unit_power[20];
80 unsigned int pdev_id;
81 unsigned int irq;
82 void __iomem *regs;
83 unsigned int rev;
87 #define MHZ (1000 * 1000)
89 #ifdef DEBUG
90 static const unsigned int div_tab[] = {
91 [0] = 1,
92 [1] = 2,
93 [2] = 4,
94 [3] = 8,
95 [4] = 16,
96 [5] = 32,
97 [6] = 64,
98 [7] = 128,
99 [8] = 3,
100 [9] = 6,
101 [10] = 12,
102 [11] = 24,
103 [12] = 48,
104 [13] = 96,
105 [14] = 192,
106 [15] = 384,
107 [16] = 5,
108 [17] = 10,
109 [18] = 20,
110 [19] = 40,
111 [20] = 80,
112 [21] = 160,
113 [22] = 320,
114 [23] = 604,
117 static unsigned long decode_div(unsigned long pll2, unsigned long val,
118 unsigned int lshft, unsigned int selbit,
119 unsigned long mask)
121 if (val & selbit)
122 pll2 = 288 * MHZ;
124 return pll2 / div_tab[(val >> lshft) & mask];
127 #define fmt_freq(x) ((x) / MHZ), ((x) % MHZ), (x)
129 /* sm501_dump_clk
131 * Print out the current clock configuration for the device
134 static void sm501_dump_clk(struct sm501_devdata *sm)
136 unsigned long misct = smc501_readl(sm->regs + SM501_MISC_TIMING);
137 unsigned long pm0 = smc501_readl(sm->regs + SM501_POWER_MODE_0_CLOCK);
138 unsigned long pm1 = smc501_readl(sm->regs + SM501_POWER_MODE_1_CLOCK);
139 unsigned long pmc = smc501_readl(sm->regs + SM501_POWER_MODE_CONTROL);
140 unsigned long sdclk0, sdclk1;
141 unsigned long pll2 = 0;
143 switch (misct & 0x30) {
144 case 0x00:
145 pll2 = 336 * MHZ;
146 break;
147 case 0x10:
148 pll2 = 288 * MHZ;
149 break;
150 case 0x20:
151 pll2 = 240 * MHZ;
152 break;
153 case 0x30:
154 pll2 = 192 * MHZ;
155 break;
158 sdclk0 = (misct & (1<<12)) ? pll2 : 288 * MHZ;
159 sdclk0 /= div_tab[((misct >> 8) & 0xf)];
161 sdclk1 = (misct & (1<<20)) ? pll2 : 288 * MHZ;
162 sdclk1 /= div_tab[((misct >> 16) & 0xf)];
164 dev_dbg(sm->dev, "MISCT=%08lx, PM0=%08lx, PM1=%08lx\n",
165 misct, pm0, pm1);
167 dev_dbg(sm->dev, "PLL2 = %ld.%ld MHz (%ld), SDCLK0=%08lx, SDCLK1=%08lx\n",
168 fmt_freq(pll2), sdclk0, sdclk1);
170 dev_dbg(sm->dev, "SDRAM: PM0=%ld, PM1=%ld\n", sdclk0, sdclk1);
172 dev_dbg(sm->dev, "PM0[%c]: "
173 "P2 %ld.%ld MHz (%ld), V2 %ld.%ld (%ld), "
174 "M %ld.%ld (%ld), MX1 %ld.%ld (%ld)\n",
175 (pmc & 3 ) == 0 ? '*' : '-',
176 fmt_freq(decode_div(pll2, pm0, 24, 1<<29, 31)),
177 fmt_freq(decode_div(pll2, pm0, 16, 1<<20, 15)),
178 fmt_freq(decode_div(pll2, pm0, 8, 1<<12, 15)),
179 fmt_freq(decode_div(pll2, pm0, 0, 1<<4, 15)));
181 dev_dbg(sm->dev, "PM1[%c]: "
182 "P2 %ld.%ld MHz (%ld), V2 %ld.%ld (%ld), "
183 "M %ld.%ld (%ld), MX1 %ld.%ld (%ld)\n",
184 (pmc & 3 ) == 1 ? '*' : '-',
185 fmt_freq(decode_div(pll2, pm1, 24, 1<<29, 31)),
186 fmt_freq(decode_div(pll2, pm1, 16, 1<<20, 15)),
187 fmt_freq(decode_div(pll2, pm1, 8, 1<<12, 15)),
188 fmt_freq(decode_div(pll2, pm1, 0, 1<<4, 15)));
191 static void sm501_dump_regs(struct sm501_devdata *sm)
193 void __iomem *regs = sm->regs;
195 dev_info(sm->dev, "System Control %08x\n",
196 smc501_readl(regs + SM501_SYSTEM_CONTROL));
197 dev_info(sm->dev, "Misc Control %08x\n",
198 smc501_readl(regs + SM501_MISC_CONTROL));
199 dev_info(sm->dev, "GPIO Control Low %08x\n",
200 smc501_readl(regs + SM501_GPIO31_0_CONTROL));
201 dev_info(sm->dev, "GPIO Control Hi %08x\n",
202 smc501_readl(regs + SM501_GPIO63_32_CONTROL));
203 dev_info(sm->dev, "DRAM Control %08x\n",
204 smc501_readl(regs + SM501_DRAM_CONTROL));
205 dev_info(sm->dev, "Arbitration Ctrl %08x\n",
206 smc501_readl(regs + SM501_ARBTRTN_CONTROL));
207 dev_info(sm->dev, "Misc Timing %08x\n",
208 smc501_readl(regs + SM501_MISC_TIMING));
211 static void sm501_dump_gate(struct sm501_devdata *sm)
213 dev_info(sm->dev, "CurrentGate %08x\n",
214 smc501_readl(sm->regs + SM501_CURRENT_GATE));
215 dev_info(sm->dev, "CurrentClock %08x\n",
216 smc501_readl(sm->regs + SM501_CURRENT_CLOCK));
217 dev_info(sm->dev, "PowerModeControl %08x\n",
218 smc501_readl(sm->regs + SM501_POWER_MODE_CONTROL));
221 #else
222 static inline void sm501_dump_gate(struct sm501_devdata *sm) { }
223 static inline void sm501_dump_regs(struct sm501_devdata *sm) { }
224 static inline void sm501_dump_clk(struct sm501_devdata *sm) { }
225 #endif
227 /* sm501_sync_regs
229 * ensure the
232 static void sm501_sync_regs(struct sm501_devdata *sm)
234 smc501_readl(sm->regs);
237 static inline void sm501_mdelay(struct sm501_devdata *sm, unsigned int delay)
239 /* during suspend/resume, we are currently not allowed to sleep,
240 * so change to using mdelay() instead of msleep() if we
241 * are in one of these paths */
243 if (sm->in_suspend)
244 mdelay(delay);
245 else
246 msleep(delay);
249 /* sm501_misc_control
251 * alters the miscellaneous control parameters
254 int sm501_misc_control(struct device *dev,
255 unsigned long set, unsigned long clear)
257 struct sm501_devdata *sm = dev_get_drvdata(dev);
258 unsigned long misc;
259 unsigned long save;
260 unsigned long to;
262 spin_lock_irqsave(&sm->reg_lock, save);
264 misc = smc501_readl(sm->regs + SM501_MISC_CONTROL);
265 to = (misc & ~clear) | set;
267 if (to != misc) {
268 smc501_writel(to, sm->regs + SM501_MISC_CONTROL);
269 sm501_sync_regs(sm);
271 dev_dbg(sm->dev, "MISC_CONTROL %08lx\n", misc);
274 spin_unlock_irqrestore(&sm->reg_lock, save);
275 return to;
278 EXPORT_SYMBOL_GPL(sm501_misc_control);
280 /* sm501_modify_reg
282 * Modify a register in the SM501 which may be shared with other
283 * drivers.
286 unsigned long sm501_modify_reg(struct device *dev,
287 unsigned long reg,
288 unsigned long set,
289 unsigned long clear)
291 struct sm501_devdata *sm = dev_get_drvdata(dev);
292 unsigned long data;
293 unsigned long save;
295 spin_lock_irqsave(&sm->reg_lock, save);
297 data = smc501_readl(sm->regs + reg);
298 data |= set;
299 data &= ~clear;
301 smc501_writel(data, sm->regs + reg);
302 sm501_sync_regs(sm);
304 spin_unlock_irqrestore(&sm->reg_lock, save);
306 return data;
309 EXPORT_SYMBOL_GPL(sm501_modify_reg);
311 /* sm501_unit_power
313 * alters the power active gate to set specific units on or off
316 int sm501_unit_power(struct device *dev, unsigned int unit, unsigned int to)
318 struct sm501_devdata *sm = dev_get_drvdata(dev);
319 unsigned long mode;
320 unsigned long gate;
321 unsigned long clock;
323 mutex_lock(&sm->clock_lock);
325 mode = smc501_readl(sm->regs + SM501_POWER_MODE_CONTROL);
326 gate = smc501_readl(sm->regs + SM501_CURRENT_GATE);
327 clock = smc501_readl(sm->regs + SM501_CURRENT_CLOCK);
329 mode &= 3; /* get current power mode */
331 if (unit >= ARRAY_SIZE(sm->unit_power)) {
332 dev_err(dev, "%s: bad unit %d\n", __func__, unit);
333 goto already;
336 dev_dbg(sm->dev, "%s: unit %d, cur %d, to %d\n", __func__, unit,
337 sm->unit_power[unit], to);
339 if (to == 0 && sm->unit_power[unit] == 0) {
340 dev_err(sm->dev, "unit %d is already shutdown\n", unit);
341 goto already;
344 sm->unit_power[unit] += to ? 1 : -1;
345 to = sm->unit_power[unit] ? 1 : 0;
347 if (to) {
348 if (gate & (1 << unit))
349 goto already;
350 gate |= (1 << unit);
351 } else {
352 if (!(gate & (1 << unit)))
353 goto already;
354 gate &= ~(1 << unit);
357 switch (mode) {
358 case 1:
359 smc501_writel(gate, sm->regs + SM501_POWER_MODE_0_GATE);
360 smc501_writel(clock, sm->regs + SM501_POWER_MODE_0_CLOCK);
361 mode = 0;
362 break;
363 case 2:
364 case 0:
365 smc501_writel(gate, sm->regs + SM501_POWER_MODE_1_GATE);
366 smc501_writel(clock, sm->regs + SM501_POWER_MODE_1_CLOCK);
367 mode = 1;
368 break;
370 default:
371 gate = -1;
372 goto already;
375 smc501_writel(mode, sm->regs + SM501_POWER_MODE_CONTROL);
376 sm501_sync_regs(sm);
378 dev_dbg(sm->dev, "gate %08lx, clock %08lx, mode %08lx\n",
379 gate, clock, mode);
381 sm501_mdelay(sm, 16);
383 already:
384 mutex_unlock(&sm->clock_lock);
385 return gate;
388 EXPORT_SYMBOL_GPL(sm501_unit_power);
391 /* Perform a rounded division. */
392 static long sm501fb_round_div(long num, long denom)
394 /* n / d + 1 / 2 = (2n + d) / 2d */
395 return (2 * num + denom) / (2 * denom);
398 /* clock value structure. */
399 struct sm501_clock {
400 unsigned long mclk;
401 int divider;
402 int shift;
403 unsigned int m, n, k;
406 /* sm501_calc_clock
408 * Calculates the nearest discrete clock frequency that
409 * can be achieved with the specified input clock.
410 * the maximum divisor is 3 or 5
413 static int sm501_calc_clock(unsigned long freq,
414 struct sm501_clock *clock,
415 int max_div,
416 unsigned long mclk,
417 long *best_diff)
419 int ret = 0;
420 int divider;
421 int shift;
422 long diff;
424 /* try dividers 1 and 3 for CRT and for panel,
425 try divider 5 for panel only.*/
427 for (divider = 1; divider <= max_div; divider += 2) {
428 /* try all 8 shift values.*/
429 for (shift = 0; shift < 8; shift++) {
430 /* Calculate difference to requested clock */
431 diff = sm501fb_round_div(mclk, divider << shift) - freq;
432 if (diff < 0)
433 diff = -diff;
435 /* If it is less than the current, use it */
436 if (diff < *best_diff) {
437 *best_diff = diff;
439 clock->mclk = mclk;
440 clock->divider = divider;
441 clock->shift = shift;
442 ret = 1;
447 return ret;
450 /* sm501_calc_pll
452 * Calculates the nearest discrete clock frequency that can be
453 * achieved using the programmable PLL.
454 * the maximum divisor is 3 or 5
457 static unsigned long sm501_calc_pll(unsigned long freq,
458 struct sm501_clock *clock,
459 int max_div)
461 unsigned long mclk;
462 unsigned int m, n, k;
463 long best_diff = 999999999;
466 * The SM502 datasheet doesn't specify the min/max values for M and N.
467 * N = 1 at least doesn't work in practice.
469 for (m = 2; m <= 255; m++) {
470 for (n = 2; n <= 127; n++) {
471 for (k = 0; k <= 1; k++) {
472 mclk = (24000000UL * m / n) >> k;
474 if (sm501_calc_clock(freq, clock, max_div,
475 mclk, &best_diff)) {
476 clock->m = m;
477 clock->n = n;
478 clock->k = k;
484 /* Return best clock. */
485 return clock->mclk / (clock->divider << clock->shift);
488 /* sm501_select_clock
490 * Calculates the nearest discrete clock frequency that can be
491 * achieved using the 288MHz and 336MHz PLLs.
492 * the maximum divisor is 3 or 5
495 static unsigned long sm501_select_clock(unsigned long freq,
496 struct sm501_clock *clock,
497 int max_div)
499 unsigned long mclk;
500 long best_diff = 999999999;
502 /* Try 288MHz and 336MHz clocks. */
503 for (mclk = 288000000; mclk <= 336000000; mclk += 48000000) {
504 sm501_calc_clock(freq, clock, max_div, mclk, &best_diff);
507 /* Return best clock. */
508 return clock->mclk / (clock->divider << clock->shift);
511 /* sm501_set_clock
513 * set one of the four clock sources to the closest available frequency to
514 * the one specified
517 unsigned long sm501_set_clock(struct device *dev,
518 int clksrc,
519 unsigned long req_freq)
521 struct sm501_devdata *sm = dev_get_drvdata(dev);
522 unsigned long mode = smc501_readl(sm->regs + SM501_POWER_MODE_CONTROL);
523 unsigned long gate = smc501_readl(sm->regs + SM501_CURRENT_GATE);
524 unsigned long clock = smc501_readl(sm->regs + SM501_CURRENT_CLOCK);
525 unsigned char reg;
526 unsigned int pll_reg = 0;
527 unsigned long sm501_freq; /* the actual frequency achieved */
529 struct sm501_clock to;
531 /* find achivable discrete frequency and setup register value
532 * accordingly, V2XCLK, MCLK and M1XCLK are the same P2XCLK
533 * has an extra bit for the divider */
535 switch (clksrc) {
536 case SM501_CLOCK_P2XCLK:
537 /* This clock is divided in half so to achieve the
538 * requested frequency the value must be multiplied by
539 * 2. This clock also has an additional pre divisor */
541 if (sm->rev >= 0xC0) {
542 /* SM502 -> use the programmable PLL */
543 sm501_freq = (sm501_calc_pll(2 * req_freq,
544 &to, 5) / 2);
545 reg = to.shift & 0x07;/* bottom 3 bits are shift */
546 if (to.divider == 3)
547 reg |= 0x08; /* /3 divider required */
548 else if (to.divider == 5)
549 reg |= 0x10; /* /5 divider required */
550 reg |= 0x40; /* select the programmable PLL */
551 pll_reg = 0x20000 | (to.k << 15) | (to.n << 8) | to.m;
552 } else {
553 sm501_freq = (sm501_select_clock(2 * req_freq,
554 &to, 5) / 2);
555 reg = to.shift & 0x07;/* bottom 3 bits are shift */
556 if (to.divider == 3)
557 reg |= 0x08; /* /3 divider required */
558 else if (to.divider == 5)
559 reg |= 0x10; /* /5 divider required */
560 if (to.mclk != 288000000)
561 reg |= 0x20; /* which mclk pll is source */
563 break;
565 case SM501_CLOCK_V2XCLK:
566 /* This clock is divided in half so to achieve the
567 * requested frequency the value must be multiplied by 2. */
569 sm501_freq = (sm501_select_clock(2 * req_freq, &to, 3) / 2);
570 reg=to.shift & 0x07; /* bottom 3 bits are shift */
571 if (to.divider == 3)
572 reg |= 0x08; /* /3 divider required */
573 if (to.mclk != 288000000)
574 reg |= 0x10; /* which mclk pll is source */
575 break;
577 case SM501_CLOCK_MCLK:
578 case SM501_CLOCK_M1XCLK:
579 /* These clocks are the same and not further divided */
581 sm501_freq = sm501_select_clock( req_freq, &to, 3);
582 reg=to.shift & 0x07; /* bottom 3 bits are shift */
583 if (to.divider == 3)
584 reg |= 0x08; /* /3 divider required */
585 if (to.mclk != 288000000)
586 reg |= 0x10; /* which mclk pll is source */
587 break;
589 default:
590 return 0; /* this is bad */
593 mutex_lock(&sm->clock_lock);
595 mode = smc501_readl(sm->regs + SM501_POWER_MODE_CONTROL);
596 gate = smc501_readl(sm->regs + SM501_CURRENT_GATE);
597 clock = smc501_readl(sm->regs + SM501_CURRENT_CLOCK);
599 clock = clock & ~(0xFF << clksrc);
600 clock |= reg<<clksrc;
602 mode &= 3; /* find current mode */
604 switch (mode) {
605 case 1:
606 smc501_writel(gate, sm->regs + SM501_POWER_MODE_0_GATE);
607 smc501_writel(clock, sm->regs + SM501_POWER_MODE_0_CLOCK);
608 mode = 0;
609 break;
610 case 2:
611 case 0:
612 smc501_writel(gate, sm->regs + SM501_POWER_MODE_1_GATE);
613 smc501_writel(clock, sm->regs + SM501_POWER_MODE_1_CLOCK);
614 mode = 1;
615 break;
617 default:
618 mutex_unlock(&sm->clock_lock);
619 return -1;
622 smc501_writel(mode, sm->regs + SM501_POWER_MODE_CONTROL);
624 if (pll_reg)
625 smc501_writel(pll_reg,
626 sm->regs + SM501_PROGRAMMABLE_PLL_CONTROL);
628 sm501_sync_regs(sm);
630 dev_dbg(sm->dev, "gate %08lx, clock %08lx, mode %08lx\n",
631 gate, clock, mode);
633 sm501_mdelay(sm, 16);
634 mutex_unlock(&sm->clock_lock);
636 sm501_dump_clk(sm);
638 return sm501_freq;
641 EXPORT_SYMBOL_GPL(sm501_set_clock);
643 /* sm501_find_clock
645 * finds the closest available frequency for a given clock
648 unsigned long sm501_find_clock(struct device *dev,
649 int clksrc,
650 unsigned long req_freq)
652 struct sm501_devdata *sm = dev_get_drvdata(dev);
653 unsigned long sm501_freq; /* the frequency achieveable by the 501 */
654 struct sm501_clock to;
656 switch (clksrc) {
657 case SM501_CLOCK_P2XCLK:
658 if (sm->rev >= 0xC0) {
659 /* SM502 -> use the programmable PLL */
660 sm501_freq = (sm501_calc_pll(2 * req_freq,
661 &to, 5) / 2);
662 } else {
663 sm501_freq = (sm501_select_clock(2 * req_freq,
664 &to, 5) / 2);
666 break;
668 case SM501_CLOCK_V2XCLK:
669 sm501_freq = (sm501_select_clock(2 * req_freq, &to, 3) / 2);
670 break;
672 case SM501_CLOCK_MCLK:
673 case SM501_CLOCK_M1XCLK:
674 sm501_freq = sm501_select_clock(req_freq, &to, 3);
675 break;
677 default:
678 sm501_freq = 0; /* error */
681 return sm501_freq;
684 EXPORT_SYMBOL_GPL(sm501_find_clock);
686 static struct sm501_device *to_sm_device(struct platform_device *pdev)
688 return container_of(pdev, struct sm501_device, pdev);
691 /* sm501_device_release
693 * A release function for the platform devices we create to allow us to
694 * free any items we allocated
697 static void sm501_device_release(struct device *dev)
699 kfree(to_sm_device(to_platform_device(dev)));
702 /* sm501_create_subdev
704 * Create a skeleton platform device with resources for passing to a
705 * sub-driver
708 static struct platform_device *
709 sm501_create_subdev(struct sm501_devdata *sm, char *name,
710 unsigned int res_count, unsigned int platform_data_size)
712 struct sm501_device *smdev;
714 smdev = kzalloc(sizeof(struct sm501_device) +
715 (sizeof(struct resource) * res_count) +
716 platform_data_size, GFP_KERNEL);
717 if (!smdev)
718 return NULL;
720 smdev->pdev.dev.release = sm501_device_release;
722 smdev->pdev.name = name;
723 smdev->pdev.id = sm->pdev_id;
724 smdev->pdev.dev.parent = sm->dev;
726 if (res_count) {
727 smdev->pdev.resource = (struct resource *)(smdev+1);
728 smdev->pdev.num_resources = res_count;
730 if (platform_data_size)
731 smdev->pdev.dev.platform_data = (void *)(smdev+1);
733 return &smdev->pdev;
736 /* sm501_register_device
738 * Register a platform device created with sm501_create_subdev()
741 static int sm501_register_device(struct sm501_devdata *sm,
742 struct platform_device *pdev)
744 struct sm501_device *smdev = to_sm_device(pdev);
745 int ptr;
746 int ret;
748 for (ptr = 0; ptr < pdev->num_resources; ptr++) {
749 printk(KERN_DEBUG "%s[%d] %pR\n",
750 pdev->name, ptr, &pdev->resource[ptr]);
753 ret = platform_device_register(pdev);
755 if (ret >= 0) {
756 dev_dbg(sm->dev, "registered %s\n", pdev->name);
757 list_add_tail(&smdev->list, &sm->devices);
758 } else
759 dev_err(sm->dev, "error registering %s (%d)\n",
760 pdev->name, ret);
762 return ret;
765 /* sm501_create_subio
767 * Fill in an IO resource for a sub device
770 static void sm501_create_subio(struct sm501_devdata *sm,
771 struct resource *res,
772 resource_size_t offs,
773 resource_size_t size)
775 res->flags = IORESOURCE_MEM;
776 res->parent = sm->io_res;
777 res->start = sm->io_res->start + offs;
778 res->end = res->start + size - 1;
781 /* sm501_create_mem
783 * Fill in an MEM resource for a sub device
786 static void sm501_create_mem(struct sm501_devdata *sm,
787 struct resource *res,
788 resource_size_t *offs,
789 resource_size_t size)
791 *offs -= size; /* adjust memory size */
793 res->flags = IORESOURCE_MEM;
794 res->parent = sm->mem_res;
795 res->start = sm->mem_res->start + *offs;
796 res->end = res->start + size - 1;
799 /* sm501_create_irq
801 * Fill in an IRQ resource for a sub device
804 static void sm501_create_irq(struct sm501_devdata *sm,
805 struct resource *res)
807 res->flags = IORESOURCE_IRQ;
808 res->parent = NULL;
809 res->start = res->end = sm->irq;
812 static int sm501_register_usbhost(struct sm501_devdata *sm,
813 resource_size_t *mem_avail)
815 struct platform_device *pdev;
817 pdev = sm501_create_subdev(sm, "sm501-usb", 3, 0);
818 if (!pdev)
819 return -ENOMEM;
821 sm501_create_subio(sm, &pdev->resource[0], 0x40000, 0x20000);
822 sm501_create_mem(sm, &pdev->resource[1], mem_avail, 256*1024);
823 sm501_create_irq(sm, &pdev->resource[2]);
825 return sm501_register_device(sm, pdev);
828 static void sm501_setup_uart_data(struct sm501_devdata *sm,
829 struct plat_serial8250_port *uart_data,
830 unsigned int offset)
832 uart_data->membase = sm->regs + offset;
833 uart_data->mapbase = sm->io_res->start + offset;
834 uart_data->iotype = UPIO_MEM;
835 uart_data->irq = sm->irq;
836 uart_data->flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
837 uart_data->regshift = 2;
838 uart_data->uartclk = (9600 * 16);
841 static int sm501_register_uart(struct sm501_devdata *sm, int devices)
843 struct platform_device *pdev;
844 struct plat_serial8250_port *uart_data;
846 pdev = sm501_create_subdev(sm, "serial8250", 0,
847 sizeof(struct plat_serial8250_port) * 3);
848 if (!pdev)
849 return -ENOMEM;
851 uart_data = pdev->dev.platform_data;
853 if (devices & SM501_USE_UART0) {
854 sm501_setup_uart_data(sm, uart_data++, 0x30000);
855 sm501_unit_power(sm->dev, SM501_GATE_UART0, 1);
856 sm501_modify_reg(sm->dev, SM501_IRQ_MASK, 1 << 12, 0);
857 sm501_modify_reg(sm->dev, SM501_GPIO63_32_CONTROL, 0x01e0, 0);
859 if (devices & SM501_USE_UART1) {
860 sm501_setup_uart_data(sm, uart_data++, 0x30020);
861 sm501_unit_power(sm->dev, SM501_GATE_UART1, 1);
862 sm501_modify_reg(sm->dev, SM501_IRQ_MASK, 1 << 13, 0);
863 sm501_modify_reg(sm->dev, SM501_GPIO63_32_CONTROL, 0x1e00, 0);
866 pdev->id = PLAT8250_DEV_SM501;
868 return sm501_register_device(sm, pdev);
871 static int sm501_register_display(struct sm501_devdata *sm,
872 resource_size_t *mem_avail)
874 struct platform_device *pdev;
876 pdev = sm501_create_subdev(sm, "sm501-fb", 4, 0);
877 if (!pdev)
878 return -ENOMEM;
880 sm501_create_subio(sm, &pdev->resource[0], 0x80000, 0x10000);
881 sm501_create_subio(sm, &pdev->resource[1], 0x100000, 0x50000);
882 sm501_create_mem(sm, &pdev->resource[2], mem_avail, *mem_avail);
883 sm501_create_irq(sm, &pdev->resource[3]);
885 return sm501_register_device(sm, pdev);
888 #ifdef CONFIG_MFD_SM501_GPIO
890 static inline struct sm501_gpio_chip *to_sm501_gpio(struct gpio_chip *gc)
892 return container_of(gc, struct sm501_gpio_chip, gpio);
895 static inline struct sm501_devdata *sm501_gpio_to_dev(struct sm501_gpio *gpio)
897 return container_of(gpio, struct sm501_devdata, gpio);
900 static int sm501_gpio_get(struct gpio_chip *chip, unsigned offset)
903 struct sm501_gpio_chip *smgpio = to_sm501_gpio(chip);
904 unsigned long result;
906 result = smc501_readl(smgpio->regbase + SM501_GPIO_DATA_LOW);
907 result >>= offset;
909 return result & 1UL;
912 static void sm501_gpio_ensure_gpio(struct sm501_gpio_chip *smchip,
913 unsigned long bit)
915 unsigned long ctrl;
917 /* check and modify if this pin is not set as gpio. */
919 if (smc501_readl(smchip->control) & bit) {
920 dev_info(sm501_gpio_to_dev(smchip->ourgpio)->dev,
921 "changing mode of gpio, bit %08lx\n", bit);
923 ctrl = smc501_readl(smchip->control);
924 ctrl &= ~bit;
925 smc501_writel(ctrl, smchip->control);
927 sm501_sync_regs(sm501_gpio_to_dev(smchip->ourgpio));
931 static void sm501_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
934 struct sm501_gpio_chip *smchip = to_sm501_gpio(chip);
935 struct sm501_gpio *smgpio = smchip->ourgpio;
936 unsigned long bit = 1 << offset;
937 void __iomem *regs = smchip->regbase;
938 unsigned long save;
939 unsigned long val;
941 dev_dbg(sm501_gpio_to_dev(smgpio)->dev, "%s(%p,%d)\n",
942 __func__, chip, offset);
944 spin_lock_irqsave(&smgpio->lock, save);
946 val = smc501_readl(regs + SM501_GPIO_DATA_LOW) & ~bit;
947 if (value)
948 val |= bit;
949 smc501_writel(val, regs);
951 sm501_sync_regs(sm501_gpio_to_dev(smgpio));
952 sm501_gpio_ensure_gpio(smchip, bit);
954 spin_unlock_irqrestore(&smgpio->lock, save);
957 static int sm501_gpio_input(struct gpio_chip *chip, unsigned offset)
959 struct sm501_gpio_chip *smchip = to_sm501_gpio(chip);
960 struct sm501_gpio *smgpio = smchip->ourgpio;
961 void __iomem *regs = smchip->regbase;
962 unsigned long bit = 1 << offset;
963 unsigned long save;
964 unsigned long ddr;
966 dev_dbg(sm501_gpio_to_dev(smgpio)->dev, "%s(%p,%d)\n",
967 __func__, chip, offset);
969 spin_lock_irqsave(&smgpio->lock, save);
971 ddr = smc501_readl(regs + SM501_GPIO_DDR_LOW);
972 smc501_writel(ddr & ~bit, regs + SM501_GPIO_DDR_LOW);
974 sm501_sync_regs(sm501_gpio_to_dev(smgpio));
975 sm501_gpio_ensure_gpio(smchip, bit);
977 spin_unlock_irqrestore(&smgpio->lock, save);
979 return 0;
982 static int sm501_gpio_output(struct gpio_chip *chip,
983 unsigned offset, int value)
985 struct sm501_gpio_chip *smchip = to_sm501_gpio(chip);
986 struct sm501_gpio *smgpio = smchip->ourgpio;
987 unsigned long bit = 1 << offset;
988 void __iomem *regs = smchip->regbase;
989 unsigned long save;
990 unsigned long val;
991 unsigned long ddr;
993 dev_dbg(sm501_gpio_to_dev(smgpio)->dev, "%s(%p,%d,%d)\n",
994 __func__, chip, offset, value);
996 spin_lock_irqsave(&smgpio->lock, save);
998 val = smc501_readl(regs + SM501_GPIO_DATA_LOW);
999 if (value)
1000 val |= bit;
1001 else
1002 val &= ~bit;
1003 smc501_writel(val, regs);
1005 ddr = smc501_readl(regs + SM501_GPIO_DDR_LOW);
1006 smc501_writel(ddr | bit, regs + SM501_GPIO_DDR_LOW);
1008 sm501_sync_regs(sm501_gpio_to_dev(smgpio));
1009 smc501_writel(val, regs + SM501_GPIO_DATA_LOW);
1011 sm501_sync_regs(sm501_gpio_to_dev(smgpio));
1012 spin_unlock_irqrestore(&smgpio->lock, save);
1014 return 0;
1017 static struct gpio_chip gpio_chip_template = {
1018 .ngpio = 32,
1019 .direction_input = sm501_gpio_input,
1020 .direction_output = sm501_gpio_output,
1021 .set = sm501_gpio_set,
1022 .get = sm501_gpio_get,
1025 static int __devinit sm501_gpio_register_chip(struct sm501_devdata *sm,
1026 struct sm501_gpio *gpio,
1027 struct sm501_gpio_chip *chip)
1029 struct sm501_platdata *pdata = sm->platdata;
1030 struct gpio_chip *gchip = &chip->gpio;
1031 int base = pdata->gpio_base;
1033 chip->gpio = gpio_chip_template;
1035 if (chip == &gpio->high) {
1036 if (base > 0)
1037 base += 32;
1038 chip->regbase = gpio->regs + SM501_GPIO_DATA_HIGH;
1039 chip->control = sm->regs + SM501_GPIO63_32_CONTROL;
1040 gchip->label = "SM501-HIGH";
1041 } else {
1042 chip->regbase = gpio->regs + SM501_GPIO_DATA_LOW;
1043 chip->control = sm->regs + SM501_GPIO31_0_CONTROL;
1044 gchip->label = "SM501-LOW";
1047 gchip->base = base;
1048 chip->ourgpio = gpio;
1050 return gpiochip_add(gchip);
1053 static int __devinit sm501_register_gpio(struct sm501_devdata *sm)
1055 struct sm501_gpio *gpio = &sm->gpio;
1056 resource_size_t iobase = sm->io_res->start + SM501_GPIO;
1057 int ret;
1058 int tmp;
1060 dev_dbg(sm->dev, "registering gpio block %08llx\n",
1061 (unsigned long long)iobase);
1063 spin_lock_init(&gpio->lock);
1065 gpio->regs_res = request_mem_region(iobase, 0x20, "sm501-gpio");
1066 if (gpio->regs_res == NULL) {
1067 dev_err(sm->dev, "gpio: failed to request region\n");
1068 return -ENXIO;
1071 gpio->regs = ioremap(iobase, 0x20);
1072 if (gpio->regs == NULL) {
1073 dev_err(sm->dev, "gpio: failed to remap registers\n");
1074 ret = -ENXIO;
1075 goto err_claimed;
1078 /* Register both our chips. */
1080 ret = sm501_gpio_register_chip(sm, gpio, &gpio->low);
1081 if (ret) {
1082 dev_err(sm->dev, "failed to add low chip\n");
1083 goto err_mapped;
1086 ret = sm501_gpio_register_chip(sm, gpio, &gpio->high);
1087 if (ret) {
1088 dev_err(sm->dev, "failed to add high chip\n");
1089 goto err_low_chip;
1092 gpio->registered = 1;
1094 return 0;
1096 err_low_chip:
1097 tmp = gpiochip_remove(&gpio->low.gpio);
1098 if (tmp) {
1099 dev_err(sm->dev, "cannot remove low chip, cannot tidy up\n");
1100 return ret;
1103 err_mapped:
1104 iounmap(gpio->regs);
1106 err_claimed:
1107 release_resource(gpio->regs_res);
1108 kfree(gpio->regs_res);
1110 return ret;
1113 static void sm501_gpio_remove(struct sm501_devdata *sm)
1115 struct sm501_gpio *gpio = &sm->gpio;
1116 int ret;
1118 if (!sm->gpio.registered)
1119 return;
1121 ret = gpiochip_remove(&gpio->low.gpio);
1122 if (ret)
1123 dev_err(sm->dev, "cannot remove low chip, cannot tidy up\n");
1125 ret = gpiochip_remove(&gpio->high.gpio);
1126 if (ret)
1127 dev_err(sm->dev, "cannot remove high chip, cannot tidy up\n");
1129 iounmap(gpio->regs);
1130 release_resource(gpio->regs_res);
1131 kfree(gpio->regs_res);
1134 static inline int sm501_gpio_pin2nr(struct sm501_devdata *sm, unsigned int pin)
1136 struct sm501_gpio *gpio = &sm->gpio;
1137 int base = (pin < 32) ? gpio->low.gpio.base : gpio->high.gpio.base;
1139 return (pin % 32) + base;
1142 static inline int sm501_gpio_isregistered(struct sm501_devdata *sm)
1144 return sm->gpio.registered;
1146 #else
1147 static inline int sm501_register_gpio(struct sm501_devdata *sm)
1149 return 0;
1152 static inline void sm501_gpio_remove(struct sm501_devdata *sm)
1156 static inline int sm501_gpio_pin2nr(struct sm501_devdata *sm, unsigned int pin)
1158 return -1;
1161 static inline int sm501_gpio_isregistered(struct sm501_devdata *sm)
1163 return 0;
1165 #endif
1167 static int sm501_register_gpio_i2c_instance(struct sm501_devdata *sm,
1168 struct sm501_platdata_gpio_i2c *iic)
1170 struct i2c_gpio_platform_data *icd;
1171 struct platform_device *pdev;
1173 pdev = sm501_create_subdev(sm, "i2c-gpio", 0,
1174 sizeof(struct i2c_gpio_platform_data));
1175 if (!pdev)
1176 return -ENOMEM;
1178 icd = pdev->dev.platform_data;
1180 /* We keep the pin_sda and pin_scl fields relative in case the
1181 * same platform data is passed to >1 SM501.
1184 icd->sda_pin = sm501_gpio_pin2nr(sm, iic->pin_sda);
1185 icd->scl_pin = sm501_gpio_pin2nr(sm, iic->pin_scl);
1186 icd->timeout = iic->timeout;
1187 icd->udelay = iic->udelay;
1189 /* note, we can't use either of the pin numbers, as the i2c-gpio
1190 * driver uses the platform.id field to generate the bus number
1191 * to register with the i2c core; The i2c core doesn't have enough
1192 * entries to deal with anything we currently use.
1195 pdev->id = iic->bus_num;
1197 dev_info(sm->dev, "registering i2c-%d: sda=%d (%d), scl=%d (%d)\n",
1198 iic->bus_num,
1199 icd->sda_pin, iic->pin_sda, icd->scl_pin, iic->pin_scl);
1201 return sm501_register_device(sm, pdev);
1204 static int sm501_register_gpio_i2c(struct sm501_devdata *sm,
1205 struct sm501_platdata *pdata)
1207 struct sm501_platdata_gpio_i2c *iic = pdata->gpio_i2c;
1208 int index;
1209 int ret;
1211 for (index = 0; index < pdata->gpio_i2c_nr; index++, iic++) {
1212 ret = sm501_register_gpio_i2c_instance(sm, iic);
1213 if (ret < 0)
1214 return ret;
1217 return 0;
1220 /* sm501_dbg_regs
1222 * Debug attribute to attach to parent device to show core registers
1225 static ssize_t sm501_dbg_regs(struct device *dev,
1226 struct device_attribute *attr, char *buff)
1228 struct sm501_devdata *sm = dev_get_drvdata(dev) ;
1229 unsigned int reg;
1230 char *ptr = buff;
1231 int ret;
1233 for (reg = 0x00; reg < 0x70; reg += 4) {
1234 ret = sprintf(ptr, "%08x = %08x\n",
1235 reg, smc501_readl(sm->regs + reg));
1236 ptr += ret;
1239 return ptr - buff;
1243 static DEVICE_ATTR(dbg_regs, 0666, sm501_dbg_regs, NULL);
1245 /* sm501_init_reg
1247 * Helper function for the init code to setup a register
1249 * clear the bits which are set in r->mask, and then set
1250 * the bits set in r->set.
1253 static inline void sm501_init_reg(struct sm501_devdata *sm,
1254 unsigned long reg,
1255 struct sm501_reg_init *r)
1257 unsigned long tmp;
1259 tmp = smc501_readl(sm->regs + reg);
1260 tmp &= ~r->mask;
1261 tmp |= r->set;
1262 smc501_writel(tmp, sm->regs + reg);
1265 /* sm501_init_regs
1267 * Setup core register values
1270 static void sm501_init_regs(struct sm501_devdata *sm,
1271 struct sm501_initdata *init)
1273 sm501_misc_control(sm->dev,
1274 init->misc_control.set,
1275 init->misc_control.mask);
1277 sm501_init_reg(sm, SM501_MISC_TIMING, &init->misc_timing);
1278 sm501_init_reg(sm, SM501_GPIO31_0_CONTROL, &init->gpio_low);
1279 sm501_init_reg(sm, SM501_GPIO63_32_CONTROL, &init->gpio_high);
1281 if (init->m1xclk) {
1282 dev_info(sm->dev, "setting M1XCLK to %ld\n", init->m1xclk);
1283 sm501_set_clock(sm->dev, SM501_CLOCK_M1XCLK, init->m1xclk);
1286 if (init->mclk) {
1287 dev_info(sm->dev, "setting MCLK to %ld\n", init->mclk);
1288 sm501_set_clock(sm->dev, SM501_CLOCK_MCLK, init->mclk);
1293 /* Check the PLL sources for the M1CLK and M1XCLK
1295 * If the M1CLK and M1XCLKs are not sourced from the same PLL, then
1296 * there is a risk (see errata AB-5) that the SM501 will cease proper
1297 * function. If this happens, then it is likely the SM501 will
1298 * hang the system.
1301 static int sm501_check_clocks(struct sm501_devdata *sm)
1303 unsigned long pwrmode = smc501_readl(sm->regs + SM501_CURRENT_CLOCK);
1304 unsigned long msrc = (pwrmode & SM501_POWERMODE_M_SRC);
1305 unsigned long m1src = (pwrmode & SM501_POWERMODE_M1_SRC);
1307 return ((msrc == 0 && m1src != 0) || (msrc != 0 && m1src == 0));
1310 static unsigned int sm501_mem_local[] = {
1311 [0] = 4*1024*1024,
1312 [1] = 8*1024*1024,
1313 [2] = 16*1024*1024,
1314 [3] = 32*1024*1024,
1315 [4] = 64*1024*1024,
1316 [5] = 2*1024*1024,
1319 /* sm501_init_dev
1321 * Common init code for an SM501
1324 static int __devinit sm501_init_dev(struct sm501_devdata *sm)
1326 struct sm501_initdata *idata;
1327 struct sm501_platdata *pdata;
1328 resource_size_t mem_avail;
1329 unsigned long dramctrl;
1330 unsigned long devid;
1331 int ret;
1333 mutex_init(&sm->clock_lock);
1334 spin_lock_init(&sm->reg_lock);
1336 INIT_LIST_HEAD(&sm->devices);
1338 devid = smc501_readl(sm->regs + SM501_DEVICEID);
1340 if ((devid & SM501_DEVICEID_IDMASK) != SM501_DEVICEID_SM501) {
1341 dev_err(sm->dev, "incorrect device id %08lx\n", devid);
1342 return -EINVAL;
1345 /* disable irqs */
1346 smc501_writel(0, sm->regs + SM501_IRQ_MASK);
1348 dramctrl = smc501_readl(sm->regs + SM501_DRAM_CONTROL);
1349 mem_avail = sm501_mem_local[(dramctrl >> 13) & 0x7];
1351 dev_info(sm->dev, "SM501 At %p: Version %08lx, %ld Mb, IRQ %d\n",
1352 sm->regs, devid, (unsigned long)mem_avail >> 20, sm->irq);
1354 sm->rev = devid & SM501_DEVICEID_REVMASK;
1356 sm501_dump_gate(sm);
1358 ret = device_create_file(sm->dev, &dev_attr_dbg_regs);
1359 if (ret)
1360 dev_err(sm->dev, "failed to create debug regs file\n");
1362 sm501_dump_clk(sm);
1364 /* check to see if we have some device initialisation */
1366 pdata = sm->platdata;
1367 idata = pdata ? pdata->init : NULL;
1369 if (idata) {
1370 sm501_init_regs(sm, idata);
1372 if (idata->devices & SM501_USE_USB_HOST)
1373 sm501_register_usbhost(sm, &mem_avail);
1374 if (idata->devices & (SM501_USE_UART0 | SM501_USE_UART1))
1375 sm501_register_uart(sm, idata->devices);
1376 if (idata->devices & SM501_USE_GPIO)
1377 sm501_register_gpio(sm);
1380 if (pdata && pdata->gpio_i2c != NULL && pdata->gpio_i2c_nr > 0) {
1381 if (!sm501_gpio_isregistered(sm))
1382 dev_err(sm->dev, "no gpio available for i2c gpio.\n");
1383 else
1384 sm501_register_gpio_i2c(sm, pdata);
1387 ret = sm501_check_clocks(sm);
1388 if (ret) {
1389 dev_err(sm->dev, "M1X and M clocks sourced from different "
1390 "PLLs\n");
1391 return -EINVAL;
1394 /* always create a framebuffer */
1395 sm501_register_display(sm, &mem_avail);
1397 return 0;
1400 static int __devinit sm501_plat_probe(struct platform_device *dev)
1402 struct sm501_devdata *sm;
1403 int ret;
1405 sm = kzalloc(sizeof(struct sm501_devdata), GFP_KERNEL);
1406 if (sm == NULL) {
1407 dev_err(&dev->dev, "no memory for device data\n");
1408 ret = -ENOMEM;
1409 goto err1;
1412 sm->dev = &dev->dev;
1413 sm->pdev_id = dev->id;
1414 sm->platdata = dev->dev.platform_data;
1416 ret = platform_get_irq(dev, 0);
1417 if (ret < 0) {
1418 dev_err(&dev->dev, "failed to get irq resource\n");
1419 goto err_res;
1421 sm->irq = ret;
1423 sm->io_res = platform_get_resource(dev, IORESOURCE_MEM, 1);
1424 sm->mem_res = platform_get_resource(dev, IORESOURCE_MEM, 0);
1426 if (sm->io_res == NULL || sm->mem_res == NULL) {
1427 dev_err(&dev->dev, "failed to get IO resource\n");
1428 ret = -ENOENT;
1429 goto err_res;
1432 sm->regs_claim = request_mem_region(sm->io_res->start,
1433 0x100, "sm501");
1435 if (sm->regs_claim == NULL) {
1436 dev_err(&dev->dev, "cannot claim registers\n");
1437 ret = -EBUSY;
1438 goto err_res;
1441 platform_set_drvdata(dev, sm);
1443 sm->regs = ioremap(sm->io_res->start, resource_size(sm->io_res));
1445 if (sm->regs == NULL) {
1446 dev_err(&dev->dev, "cannot remap registers\n");
1447 ret = -EIO;
1448 goto err_claim;
1451 return sm501_init_dev(sm);
1453 err_claim:
1454 release_resource(sm->regs_claim);
1455 kfree(sm->regs_claim);
1456 err_res:
1457 kfree(sm);
1458 err1:
1459 return ret;
1463 #ifdef CONFIG_PM
1465 /* power management support */
1467 static void sm501_set_power(struct sm501_devdata *sm, int on)
1469 struct sm501_platdata *pd = sm->platdata;
1471 if (pd == NULL)
1472 return;
1474 if (pd->get_power) {
1475 if (pd->get_power(sm->dev) == on) {
1476 dev_dbg(sm->dev, "is already %d\n", on);
1477 return;
1481 if (pd->set_power) {
1482 dev_dbg(sm->dev, "setting power to %d\n", on);
1484 pd->set_power(sm->dev, on);
1485 sm501_mdelay(sm, 10);
1489 static int sm501_plat_suspend(struct platform_device *pdev, pm_message_t state)
1491 struct sm501_devdata *sm = platform_get_drvdata(pdev);
1493 sm->in_suspend = 1;
1494 sm->pm_misc = smc501_readl(sm->regs + SM501_MISC_CONTROL);
1496 sm501_dump_regs(sm);
1498 if (sm->platdata) {
1499 if (sm->platdata->flags & SM501_FLAG_SUSPEND_OFF)
1500 sm501_set_power(sm, 0);
1503 return 0;
1506 static int sm501_plat_resume(struct platform_device *pdev)
1508 struct sm501_devdata *sm = platform_get_drvdata(pdev);
1510 sm501_set_power(sm, 1);
1512 sm501_dump_regs(sm);
1513 sm501_dump_gate(sm);
1514 sm501_dump_clk(sm);
1516 /* check to see if we are in the same state as when suspended */
1518 if (smc501_readl(sm->regs + SM501_MISC_CONTROL) != sm->pm_misc) {
1519 dev_info(sm->dev, "SM501_MISC_CONTROL changed over sleep\n");
1520 smc501_writel(sm->pm_misc, sm->regs + SM501_MISC_CONTROL);
1522 /* our suspend causes the controller state to change,
1523 * either by something attempting setup, power loss,
1524 * or an external reset event on power change */
1526 if (sm->platdata && sm->platdata->init) {
1527 sm501_init_regs(sm, sm->platdata->init);
1531 /* dump our state from resume */
1533 sm501_dump_regs(sm);
1534 sm501_dump_clk(sm);
1536 sm->in_suspend = 0;
1538 return 0;
1540 #else
1541 #define sm501_plat_suspend NULL
1542 #define sm501_plat_resume NULL
1543 #endif
1545 /* Initialisation data for PCI devices */
1547 static struct sm501_initdata sm501_pci_initdata = {
1548 .gpio_high = {
1549 .set = 0x3F000000, /* 24bit panel */
1550 .mask = 0x0,
1552 .misc_timing = {
1553 .set = 0x010100, /* SDRAM timing */
1554 .mask = 0x1F1F00,
1556 .misc_control = {
1557 .set = SM501_MISC_PNL_24BIT,
1558 .mask = 0,
1561 .devices = SM501_USE_ALL,
1563 /* Errata AB-3 says that 72MHz is the fastest available
1564 * for 33MHZ PCI with proper bus-mastering operation */
1566 .mclk = 72 * MHZ,
1567 .m1xclk = 144 * MHZ,
1570 static struct sm501_platdata_fbsub sm501_pdata_fbsub = {
1571 .flags = (SM501FB_FLAG_USE_INIT_MODE |
1572 SM501FB_FLAG_USE_HWCURSOR |
1573 SM501FB_FLAG_USE_HWACCEL |
1574 SM501FB_FLAG_DISABLE_AT_EXIT),
1577 static struct sm501_platdata_fb sm501_fb_pdata = {
1578 .fb_route = SM501_FB_OWN,
1579 .fb_crt = &sm501_pdata_fbsub,
1580 .fb_pnl = &sm501_pdata_fbsub,
1583 static struct sm501_platdata sm501_pci_platdata = {
1584 .init = &sm501_pci_initdata,
1585 .fb = &sm501_fb_pdata,
1586 .gpio_base = -1,
1589 static int __devinit sm501_pci_probe(struct pci_dev *dev,
1590 const struct pci_device_id *id)
1592 struct sm501_devdata *sm;
1593 int err;
1595 sm = kzalloc(sizeof(struct sm501_devdata), GFP_KERNEL);
1596 if (sm == NULL) {
1597 dev_err(&dev->dev, "no memory for device data\n");
1598 err = -ENOMEM;
1599 goto err1;
1602 /* set a default set of platform data */
1603 dev->dev.platform_data = sm->platdata = &sm501_pci_platdata;
1605 /* set a hopefully unique id for our child platform devices */
1606 sm->pdev_id = 32 + dev->devfn;
1608 pci_set_drvdata(dev, sm);
1610 err = pci_enable_device(dev);
1611 if (err) {
1612 dev_err(&dev->dev, "cannot enable device\n");
1613 goto err2;
1616 sm->dev = &dev->dev;
1617 sm->irq = dev->irq;
1619 #ifdef __BIG_ENDIAN
1620 /* if the system is big-endian, we most probably have a
1621 * translation in the IO layer making the PCI bus little endian
1622 * so make the framebuffer swapped pixels */
1624 sm501_fb_pdata.flags |= SM501_FBPD_SWAP_FB_ENDIAN;
1625 #endif
1627 /* check our resources */
1629 if (!(pci_resource_flags(dev, 0) & IORESOURCE_MEM)) {
1630 dev_err(&dev->dev, "region #0 is not memory?\n");
1631 err = -EINVAL;
1632 goto err3;
1635 if (!(pci_resource_flags(dev, 1) & IORESOURCE_MEM)) {
1636 dev_err(&dev->dev, "region #1 is not memory?\n");
1637 err = -EINVAL;
1638 goto err3;
1641 /* make our resources ready for sharing */
1643 sm->io_res = &dev->resource[1];
1644 sm->mem_res = &dev->resource[0];
1646 sm->regs_claim = request_mem_region(sm->io_res->start,
1647 0x100, "sm501");
1648 if (sm->regs_claim == NULL) {
1649 dev_err(&dev->dev, "cannot claim registers\n");
1650 err= -EBUSY;
1651 goto err3;
1654 sm->regs = pci_ioremap_bar(dev, 1);
1656 if (sm->regs == NULL) {
1657 dev_err(&dev->dev, "cannot remap registers\n");
1658 err = -EIO;
1659 goto err4;
1662 sm501_init_dev(sm);
1663 return 0;
1665 err4:
1666 release_resource(sm->regs_claim);
1667 kfree(sm->regs_claim);
1668 err3:
1669 pci_disable_device(dev);
1670 err2:
1671 pci_set_drvdata(dev, NULL);
1672 kfree(sm);
1673 err1:
1674 return err;
1677 static void sm501_remove_sub(struct sm501_devdata *sm,
1678 struct sm501_device *smdev)
1680 list_del(&smdev->list);
1681 platform_device_unregister(&smdev->pdev);
1684 static void sm501_dev_remove(struct sm501_devdata *sm)
1686 struct sm501_device *smdev, *tmp;
1688 list_for_each_entry_safe(smdev, tmp, &sm->devices, list)
1689 sm501_remove_sub(sm, smdev);
1691 device_remove_file(sm->dev, &dev_attr_dbg_regs);
1693 sm501_gpio_remove(sm);
1696 static void __devexit sm501_pci_remove(struct pci_dev *dev)
1698 struct sm501_devdata *sm = pci_get_drvdata(dev);
1700 sm501_dev_remove(sm);
1701 iounmap(sm->regs);
1703 release_resource(sm->regs_claim);
1704 kfree(sm->regs_claim);
1706 pci_set_drvdata(dev, NULL);
1707 pci_disable_device(dev);
1710 static int sm501_plat_remove(struct platform_device *dev)
1712 struct sm501_devdata *sm = platform_get_drvdata(dev);
1714 sm501_dev_remove(sm);
1715 iounmap(sm->regs);
1717 release_resource(sm->regs_claim);
1718 kfree(sm->regs_claim);
1720 return 0;
1723 static struct pci_device_id sm501_pci_tbl[] = {
1724 { 0x126f, 0x0501, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
1725 { 0, },
1728 MODULE_DEVICE_TABLE(pci, sm501_pci_tbl);
1730 static struct pci_driver sm501_pci_driver = {
1731 .name = "sm501",
1732 .id_table = sm501_pci_tbl,
1733 .probe = sm501_pci_probe,
1734 .remove = __devexit_p(sm501_pci_remove),
1737 MODULE_ALIAS("platform:sm501");
1739 static struct of_device_id __devinitdata of_sm501_match_tbl[] = {
1740 { .compatible = "smi,sm501", },
1741 { /* end */ }
1744 static struct platform_driver sm501_plat_driver = {
1745 .driver = {
1746 .name = "sm501",
1747 .owner = THIS_MODULE,
1748 .of_match_table = of_sm501_match_tbl,
1750 .probe = sm501_plat_probe,
1751 .remove = sm501_plat_remove,
1752 .suspend = sm501_plat_suspend,
1753 .resume = sm501_plat_resume,
1756 static int __init sm501_base_init(void)
1758 platform_driver_register(&sm501_plat_driver);
1759 return pci_register_driver(&sm501_pci_driver);
1762 static void __exit sm501_base_exit(void)
1764 platform_driver_unregister(&sm501_plat_driver);
1765 pci_unregister_driver(&sm501_pci_driver);
1768 module_init(sm501_base_init);
1769 module_exit(sm501_base_exit);
1771 MODULE_DESCRIPTION("SM501 Core Driver");
1772 MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>, Vincent Sanders");
1773 MODULE_LICENSE("GPL v2");