Merge remote-tracking branch 'arm/for-next'
[linux-2.6/next.git] / sound / soc / ep93xx / ep93xx-ac97.c
blobc7417c76552b50a10e45b0ff7949309e2c945850
1 /*
2 * ASoC driver for Cirrus Logic EP93xx AC97 controller.
4 * Copyright (c) 2010 Mika Westerberg
6 * Based on s3c-ac97 ASoC driver by Jaswinder Singh.
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License version 2 as
10 * published by the Free Software Foundation.
13 #include <linux/delay.h>
14 #include <linux/io.h>
15 #include <linux/init.h>
16 #include <linux/module.h>
17 #include <linux/platform_device.h>
18 #include <linux/slab.h>
20 #include <sound/core.h>
21 #include <sound/ac97_codec.h>
22 #include <sound/soc.h>
24 #include <mach/dma.h>
25 #include "ep93xx-pcm.h"
28 * Per channel (1-4) registers.
30 #define AC97CH(n) (((n) - 1) * 0x20)
32 #define AC97DR(n) (AC97CH(n) + 0x0000)
34 #define AC97RXCR(n) (AC97CH(n) + 0x0004)
35 #define AC97RXCR_REN BIT(0)
36 #define AC97RXCR_RX3 BIT(3)
37 #define AC97RXCR_RX4 BIT(4)
38 #define AC97RXCR_CM BIT(15)
40 #define AC97TXCR(n) (AC97CH(n) + 0x0008)
41 #define AC97TXCR_TEN BIT(0)
42 #define AC97TXCR_TX3 BIT(3)
43 #define AC97TXCR_TX4 BIT(4)
44 #define AC97TXCR_CM BIT(15)
46 #define AC97SR(n) (AC97CH(n) + 0x000c)
47 #define AC97SR_TXFE BIT(1)
48 #define AC97SR_TXUE BIT(6)
50 #define AC97RISR(n) (AC97CH(n) + 0x0010)
51 #define AC97ISR(n) (AC97CH(n) + 0x0014)
52 #define AC97IE(n) (AC97CH(n) + 0x0018)
55 * Global AC97 controller registers.
57 #define AC97S1DATA 0x0080
58 #define AC97S2DATA 0x0084
59 #define AC97S12DATA 0x0088
61 #define AC97RGIS 0x008c
62 #define AC97GIS 0x0090
63 #define AC97IM 0x0094
65 * Common bits for RGIS, GIS and IM registers.
67 #define AC97_SLOT2RXVALID BIT(1)
68 #define AC97_CODECREADY BIT(5)
69 #define AC97_SLOT2TXCOMPLETE BIT(6)
71 #define AC97EOI 0x0098
72 #define AC97EOI_WINT BIT(0)
73 #define AC97EOI_CODECREADY BIT(1)
75 #define AC97GCR 0x009c
76 #define AC97GCR_AC97IFE BIT(0)
78 #define AC97RESET 0x00a0
79 #define AC97RESET_TIMEDRESET BIT(0)
81 #define AC97SYNC 0x00a4
82 #define AC97SYNC_TIMEDSYNC BIT(0)
84 #define AC97_TIMEOUT msecs_to_jiffies(5)
86 /**
87 * struct ep93xx_ac97_info - EP93xx AC97 controller info structure
88 * @lock: mutex serializing access to the bus (slot 1 & 2 ops)
89 * @dev: pointer to the platform device dev structure
90 * @mem: physical memory resource for the registers
91 * @regs: mapped AC97 controller registers
92 * @irq: AC97 interrupt number
93 * @done: bus ops wait here for an interrupt
95 struct ep93xx_ac97_info {
96 struct mutex lock;
97 struct device *dev;
98 struct resource *mem;
99 void __iomem *regs;
100 int irq;
101 struct completion done;
104 /* currently ALSA only supports a single AC97 device */
105 static struct ep93xx_ac97_info *ep93xx_ac97_info;
107 static struct ep93xx_pcm_dma_params ep93xx_ac97_pcm_out = {
108 .name = "ac97-pcm-out",
109 .dma_port = EP93XX_DMA_AAC1,
112 static struct ep93xx_pcm_dma_params ep93xx_ac97_pcm_in = {
113 .name = "ac97-pcm-in",
114 .dma_port = EP93XX_DMA_AAC1,
117 static inline unsigned ep93xx_ac97_read_reg(struct ep93xx_ac97_info *info,
118 unsigned reg)
120 return __raw_readl(info->regs + reg);
123 static inline void ep93xx_ac97_write_reg(struct ep93xx_ac97_info *info,
124 unsigned reg, unsigned val)
126 __raw_writel(val, info->regs + reg);
129 static unsigned short ep93xx_ac97_read(struct snd_ac97 *ac97,
130 unsigned short reg)
132 struct ep93xx_ac97_info *info = ep93xx_ac97_info;
133 unsigned short val;
135 mutex_lock(&info->lock);
137 ep93xx_ac97_write_reg(info, AC97S1DATA, reg);
138 ep93xx_ac97_write_reg(info, AC97IM, AC97_SLOT2RXVALID);
139 if (!wait_for_completion_timeout(&info->done, AC97_TIMEOUT)) {
140 dev_warn(info->dev, "timeout reading register %x\n", reg);
141 mutex_unlock(&info->lock);
142 return -ETIMEDOUT;
144 val = (unsigned short)ep93xx_ac97_read_reg(info, AC97S2DATA);
146 mutex_unlock(&info->lock);
147 return val;
150 static void ep93xx_ac97_write(struct snd_ac97 *ac97,
151 unsigned short reg,
152 unsigned short val)
154 struct ep93xx_ac97_info *info = ep93xx_ac97_info;
156 mutex_lock(&info->lock);
159 * Writes to the codec need to be done so that slot 2 is filled in
160 * before slot 1.
162 ep93xx_ac97_write_reg(info, AC97S2DATA, val);
163 ep93xx_ac97_write_reg(info, AC97S1DATA, reg);
165 ep93xx_ac97_write_reg(info, AC97IM, AC97_SLOT2TXCOMPLETE);
166 if (!wait_for_completion_timeout(&info->done, AC97_TIMEOUT))
167 dev_warn(info->dev, "timeout writing register %x\n", reg);
169 mutex_unlock(&info->lock);
172 static void ep93xx_ac97_warm_reset(struct snd_ac97 *ac97)
174 struct ep93xx_ac97_info *info = ep93xx_ac97_info;
176 mutex_lock(&info->lock);
179 * We are assuming that before this functions gets called, the codec
180 * BIT_CLK is stopped by forcing the codec into powerdown mode. We can
181 * control the SYNC signal directly via AC97SYNC register. Using
182 * TIMEDSYNC the controller will keep the SYNC high > 1us.
184 ep93xx_ac97_write_reg(info, AC97SYNC, AC97SYNC_TIMEDSYNC);
185 ep93xx_ac97_write_reg(info, AC97IM, AC97_CODECREADY);
186 if (!wait_for_completion_timeout(&info->done, AC97_TIMEOUT))
187 dev_warn(info->dev, "codec warm reset timeout\n");
189 mutex_unlock(&info->lock);
192 static void ep93xx_ac97_cold_reset(struct snd_ac97 *ac97)
194 struct ep93xx_ac97_info *info = ep93xx_ac97_info;
196 mutex_lock(&info->lock);
199 * For doing cold reset, we disable the AC97 controller interface, clear
200 * WINT and CODECREADY bits, and finally enable the interface again.
202 ep93xx_ac97_write_reg(info, AC97GCR, 0);
203 ep93xx_ac97_write_reg(info, AC97EOI, AC97EOI_CODECREADY | AC97EOI_WINT);
204 ep93xx_ac97_write_reg(info, AC97GCR, AC97GCR_AC97IFE);
207 * Now, assert the reset and wait for the codec to become ready.
209 ep93xx_ac97_write_reg(info, AC97RESET, AC97RESET_TIMEDRESET);
210 ep93xx_ac97_write_reg(info, AC97IM, AC97_CODECREADY);
211 if (!wait_for_completion_timeout(&info->done, AC97_TIMEOUT))
212 dev_warn(info->dev, "codec cold reset timeout\n");
215 * Give the codec some time to come fully out from the reset. This way
216 * we ensure that the subsequent reads/writes will work.
218 usleep_range(15000, 20000);
220 mutex_unlock(&info->lock);
223 static irqreturn_t ep93xx_ac97_interrupt(int irq, void *dev_id)
225 struct ep93xx_ac97_info *info = dev_id;
226 unsigned status, mask;
229 * Just mask out the interrupt and wake up the waiting thread.
230 * Interrupts are cleared via reading/writing to slot 1 & 2 registers by
231 * the waiting thread.
233 status = ep93xx_ac97_read_reg(info, AC97GIS);
234 mask = ep93xx_ac97_read_reg(info, AC97IM);
235 mask &= ~status;
236 ep93xx_ac97_write_reg(info, AC97IM, mask);
238 complete(&info->done);
239 return IRQ_HANDLED;
242 struct snd_ac97_bus_ops soc_ac97_ops = {
243 .read = ep93xx_ac97_read,
244 .write = ep93xx_ac97_write,
245 .reset = ep93xx_ac97_cold_reset,
246 .warm_reset = ep93xx_ac97_warm_reset,
248 EXPORT_SYMBOL_GPL(soc_ac97_ops);
250 static int ep93xx_ac97_trigger(struct snd_pcm_substream *substream,
251 int cmd, struct snd_soc_dai *dai)
253 struct ep93xx_ac97_info *info = snd_soc_dai_get_drvdata(dai);
254 unsigned v = 0;
256 switch (cmd) {
257 case SNDRV_PCM_TRIGGER_START:
258 case SNDRV_PCM_TRIGGER_RESUME:
259 case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
260 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
262 * Enable compact mode, TX slots 3 & 4, and the TX FIFO
263 * itself.
265 v |= AC97TXCR_CM;
266 v |= AC97TXCR_TX3 | AC97TXCR_TX4;
267 v |= AC97TXCR_TEN;
268 ep93xx_ac97_write_reg(info, AC97TXCR(1), v);
269 } else {
271 * Enable compact mode, RX slots 3 & 4, and the RX FIFO
272 * itself.
274 v |= AC97RXCR_CM;
275 v |= AC97RXCR_RX3 | AC97RXCR_RX4;
276 v |= AC97RXCR_REN;
277 ep93xx_ac97_write_reg(info, AC97RXCR(1), v);
279 break;
281 case SNDRV_PCM_TRIGGER_STOP:
282 case SNDRV_PCM_TRIGGER_SUSPEND:
283 case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
284 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
286 * As per Cirrus EP93xx errata described below:
288 * http://www.cirrus.com/en/pubs/errata/ER667E2B.pdf
290 * we will wait for the TX FIFO to be empty before
291 * clearing the TEN bit.
293 unsigned long timeout = jiffies + AC97_TIMEOUT;
295 do {
296 v = ep93xx_ac97_read_reg(info, AC97SR(1));
297 if (time_after(jiffies, timeout)) {
298 dev_warn(info->dev, "TX timeout\n");
299 break;
301 } while (!(v & (AC97SR_TXFE | AC97SR_TXUE)));
303 /* disable the TX FIFO */
304 ep93xx_ac97_write_reg(info, AC97TXCR(1), 0);
305 } else {
306 /* disable the RX FIFO */
307 ep93xx_ac97_write_reg(info, AC97RXCR(1), 0);
309 break;
311 default:
312 dev_warn(info->dev, "unknown command %d\n", cmd);
313 return -EINVAL;
316 return 0;
319 static int ep93xx_ac97_startup(struct snd_pcm_substream *substream,
320 struct snd_soc_dai *dai)
322 struct ep93xx_pcm_dma_params *dma_data;
324 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
325 dma_data = &ep93xx_ac97_pcm_out;
326 else
327 dma_data = &ep93xx_ac97_pcm_in;
329 snd_soc_dai_set_dma_data(dai, substream, dma_data);
330 return 0;
333 static struct snd_soc_dai_ops ep93xx_ac97_dai_ops = {
334 .startup = ep93xx_ac97_startup,
335 .trigger = ep93xx_ac97_trigger,
338 struct snd_soc_dai_driver ep93xx_ac97_dai = {
339 .name = "ep93xx-ac97",
340 .id = 0,
341 .ac97_control = 1,
342 .playback = {
343 .stream_name = "AC97 Playback",
344 .channels_min = 2,
345 .channels_max = 2,
346 .rates = SNDRV_PCM_RATE_8000_48000,
347 .formats = SNDRV_PCM_FMTBIT_S16_LE,
349 .capture = {
350 .stream_name = "AC97 Capture",
351 .channels_min = 2,
352 .channels_max = 2,
353 .rates = SNDRV_PCM_RATE_8000_48000,
354 .formats = SNDRV_PCM_FMTBIT_S16_LE,
356 .ops = &ep93xx_ac97_dai_ops,
359 static int __devinit ep93xx_ac97_probe(struct platform_device *pdev)
361 struct ep93xx_ac97_info *info;
362 int ret;
364 info = kzalloc(sizeof(struct ep93xx_ac97_info), GFP_KERNEL);
365 if (!info)
366 return -ENOMEM;
368 dev_set_drvdata(&pdev->dev, info);
370 mutex_init(&info->lock);
371 init_completion(&info->done);
372 info->dev = &pdev->dev;
374 info->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
375 if (!info->mem) {
376 ret = -ENXIO;
377 goto fail_free_info;
380 info->irq = platform_get_irq(pdev, 0);
381 if (!info->irq) {
382 ret = -ENXIO;
383 goto fail_free_info;
386 if (!request_mem_region(info->mem->start, resource_size(info->mem),
387 pdev->name)) {
388 ret = -EBUSY;
389 goto fail_free_info;
392 info->regs = ioremap(info->mem->start, resource_size(info->mem));
393 if (!info->regs) {
394 ret = -ENOMEM;
395 goto fail_release_mem;
398 ret = request_irq(info->irq, ep93xx_ac97_interrupt, IRQF_TRIGGER_HIGH,
399 pdev->name, info);
400 if (ret)
401 goto fail_unmap_mem;
403 ep93xx_ac97_info = info;
404 platform_set_drvdata(pdev, info);
406 ret = snd_soc_register_dai(&pdev->dev, &ep93xx_ac97_dai);
407 if (ret)
408 goto fail_free_irq;
410 return 0;
412 fail_free_irq:
413 platform_set_drvdata(pdev, NULL);
414 free_irq(info->irq, info);
415 fail_unmap_mem:
416 iounmap(info->regs);
417 fail_release_mem:
418 release_mem_region(info->mem->start, resource_size(info->mem));
419 fail_free_info:
420 kfree(info);
422 return ret;
425 static int __devexit ep93xx_ac97_remove(struct platform_device *pdev)
427 struct ep93xx_ac97_info *info = platform_get_drvdata(pdev);
429 snd_soc_unregister_dai(&pdev->dev);
431 /* disable the AC97 controller */
432 ep93xx_ac97_write_reg(info, AC97GCR, 0);
434 free_irq(info->irq, info);
435 iounmap(info->regs);
436 release_mem_region(info->mem->start, resource_size(info->mem));
437 platform_set_drvdata(pdev, NULL);
438 kfree(info);
440 return 0;
443 static struct platform_driver ep93xx_ac97_driver = {
444 .probe = ep93xx_ac97_probe,
445 .remove = __devexit_p(ep93xx_ac97_remove),
446 .driver = {
447 .name = "ep93xx-ac97",
448 .owner = THIS_MODULE,
452 static int __init ep93xx_ac97_init(void)
454 return platform_driver_register(&ep93xx_ac97_driver);
456 module_init(ep93xx_ac97_init);
458 static void __exit ep93xx_ac97_exit(void)
460 platform_driver_unregister(&ep93xx_ac97_driver);
462 module_exit(ep93xx_ac97_exit);
464 MODULE_DESCRIPTION("EP93xx AC97 ASoC Driver");
465 MODULE_AUTHOR("Mika Westerberg <mika.westerberg@iki.fi>");
466 MODULE_LICENSE("GPL");
467 MODULE_ALIAS("platform:ep93xx-ac97");