include/scsi/scsi.h

   1 /*
   2  * This header file contains public constants and structures used by
   3  * the scsi code for linux.
   4  *
   5  * For documentation on the OPCODES, MESSAGES, and SENSE values,
   6  * please consult the SCSI standard.
   7  */
   8 #ifndef _SCSI_SCSI_H
   9 #define _SCSI_SCSI_H
  10
  11 #include <linux/types.h>
  12
  13 /*
  14  * The maximum number of SG segments that we will put inside a
  15  * scatterlist (unless chaining is used). Should ideally fit inside a
  16  * single page, to avoid a higher order allocation.  We could define this
  17  * to SG_MAX_SINGLE_ALLOC to pack correctly at the highest order.  The
  18  * minimum value is 32
  19  */
  20 #define SCSI_MAX_SG_SEGMENTS    128
  21
  22 /*
  23  * Like SCSI_MAX_SG_SEGMENTS, but for archs that have sg chaining. This limit
  24  * is totally arbitrary, a setting of 2048 will get you at least 8mb ios.
  25  */
  26 #ifdef ARCH_HAS_SG_CHAIN
  27 #define SCSI_MAX_SG_CHAIN_SEGMENTS      2048
  28 #else
  29 #define SCSI_MAX_SG_CHAIN_SEGMENTS      SCSI_MAX_SG_SEGMENTS
  30 #endif
  31
  32 /*
  33  * Special value for scanning to specify scanning or rescanning of all
  34  * possible channels, (target) ids, or luns on a given shost.
  35  */
  36 #define SCAN_WILD_CARD  ~0
  37
  38 /*
  39  *      SCSI opcodes
  40  */
  41
  42 #define TEST_UNIT_READY       0x00
  43 #define REZERO_UNIT           0x01
  44 #define REQUEST_SENSE         0x03
  45 #define FORMAT_UNIT           0x04
  46 #define READ_BLOCK_LIMITS     0x05
  47 #define REASSIGN_BLOCKS       0x07
  48 #define INITIALIZE_ELEMENT_STATUS 0x07
  49 #define READ_6                0x08
  50 #define WRITE_6               0x0a
  51 #define SEEK_6                0x0b
  52 #define READ_REVERSE          0x0f
  53 #define WRITE_FILEMARKS       0x10
  54 #define SPACE                 0x11
  55 #define INQUIRY               0x12
  56 #define RECOVER_BUFFERED_DATA 0x14
  57 #define MODE_SELECT           0x15
  58 #define RESERVE               0x16
  59 #define RELEASE               0x17
  60 #define COPY                  0x18
  61 #define ERASE                 0x19
  62 #define MODE_SENSE            0x1a
  63 #define START_STOP            0x1b
  64 #define RECEIVE_DIAGNOSTIC    0x1c
  65 #define SEND_DIAGNOSTIC       0x1d
  66 #define ALLOW_MEDIUM_REMOVAL  0x1e
  67
  68 #define SET_WINDOW            0x24
  69 #define READ_CAPACITY         0x25
  70 #define READ_10               0x28
  71 #define WRITE_10              0x2a
  72 #define SEEK_10               0x2b
  73 #define POSITION_TO_ELEMENT   0x2b
  74 #define WRITE_VERIFY          0x2e
  75 #define VERIFY                0x2f
  76 #define SEARCH_HIGH           0x30
  77 #define SEARCH_EQUAL          0x31
  78 #define SEARCH_LOW            0x32
  79 #define SET_LIMITS            0x33
  80 #define PRE_FETCH             0x34
  81 #define READ_POSITION         0x34
  82 #define SYNCHRONIZE_CACHE     0x35
  83 #define LOCK_UNLOCK_CACHE     0x36
  84 #define READ_DEFECT_DATA      0x37
  85 #define MEDIUM_SCAN           0x38
  86 #define COMPARE               0x39
  87 #define COPY_VERIFY           0x3a
  88 #define WRITE_BUFFER          0x3b
  89 #define READ_BUFFER           0x3c
  90 #define UPDATE_BLOCK          0x3d
  91 #define READ_LONG             0x3e
  92 #define WRITE_LONG            0x3f
  93 #define CHANGE_DEFINITION     0x40
  94 #define WRITE_SAME            0x41
  95 #define READ_TOC              0x43
  96 #define LOG_SELECT            0x4c
  97 #define LOG_SENSE             0x4d
  98 #define XDWRITEREAD_10        0x53
  99 #define MODE_SELECT_10        0x55
 100 #define RESERVE_10            0x56
 101 #define RELEASE_10            0x57
 102 #define MODE_SENSE_10         0x5a
 103 #define PERSISTENT_RESERVE_IN 0x5e
 104 #define PERSISTENT_RESERVE_OUT 0x5f
 105 #define VARIABLE_LENGTH_CMD   0x7f
 106 #define REPORT_LUNS           0xa0
 107 #define MAINTENANCE_IN        0xa3
 108 #define MOVE_MEDIUM           0xa5
 109 #define EXCHANGE_MEDIUM       0xa6
 110 #define READ_12               0xa8
 111 #define WRITE_12              0xaa
 112 #define WRITE_VERIFY_12       0xae
 113 #define SEARCH_HIGH_12        0xb0
 114 #define SEARCH_EQUAL_12       0xb1
 115 #define SEARCH_LOW_12         0xb2
 116 #define READ_ELEMENT_STATUS   0xb8
 117 #define SEND_VOLUME_TAG       0xb6
 118 #define WRITE_LONG_2          0xea
 119 #define READ_16               0x88
 120 #define WRITE_16              0x8a
 121 #define VERIFY_16             0x8f
 122 #define SERVICE_ACTION_IN     0x9e
 123 /* values for service action in */
 124 #define SAI_READ_CAPACITY_16  0x10
 125 /* values for maintenance in */
 126 #define MI_REPORT_TARGET_PGS  0x0a
 127
 128 /* Values for T10/04-262r7 */
 129 #define ATA_16                0x85      /* 16-byte pass-thru */
 130 #define ATA_12                0xa1      /* 12-byte pass-thru */
 131
 132 /*
 133  *      SCSI command lengths
 134  */
 135
 136 #define SCSI_MAX_VARLEN_CDB_SIZE 260
 137
 138 /* defined in T10 SCSI Primary Commands-2 (SPC2) */
 139 struct scsi_varlen_cdb_hdr {
 140         u8 opcode;        /* opcode always == VARIABLE_LENGTH_CMD */
 141         u8 control;
 142         u8 misc[5];
 143         u8 additional_cdb_length;         /* total cdb length - 8 */
 144         __be16 service_action;
 145         /* service specific data follows */
 146 };
 147
 148 static inline unsigned
 149 scsi_varlen_cdb_length(const void *hdr)
 150 {
 151         return ((struct scsi_varlen_cdb_hdr *)hdr)->additional_cdb_length + 8;
 152 }
 153
 154 extern const unsigned char scsi_command_size_tbl[8];
 155 #define COMMAND_SIZE(opcode) scsi_command_size_tbl[((opcode) >> 5) & 7]
 156
 157 static inline unsigned
 158 scsi_command_size(const unsigned char *cmnd)
 159 {
 160         return (cmnd[0] == VARIABLE_LENGTH_CMD) ?
 161                 scsi_varlen_cdb_length(cmnd) : COMMAND_SIZE(cmnd[0]);
 162 }
 163
 164 /*
 165  *  SCSI Architecture Model (SAM) Status codes. Taken from SAM-3 draft
 166  *  T10/1561-D Revision 4 Draft dated 7th November 2002.
 167  */
 168 #define SAM_STAT_GOOD            0x00
 169 #define SAM_STAT_CHECK_CONDITION 0x02
 170 #define SAM_STAT_CONDITION_MET   0x04
 171 #define SAM_STAT_BUSY            0x08
 172 #define SAM_STAT_INTERMEDIATE    0x10
 173 #define SAM_STAT_INTERMEDIATE_CONDITION_MET 0x14
 174 #define SAM_STAT_RESERVATION_CONFLICT 0x18
 175 #define SAM_STAT_COMMAND_TERMINATED 0x22        /* obsolete in SAM-3 */
 176 #define SAM_STAT_TASK_SET_FULL   0x28
 177 #define SAM_STAT_ACA_ACTIVE      0x30
 178 #define SAM_STAT_TASK_ABORTED    0x40
 179
 180 /** scsi_status_is_good - check the status return.
 181  *
 182  * @status: the status passed up from the driver (including host and
 183  *          driver components)
 184  *
 185  * This returns true for known good conditions that may be treated as
 186  * command completed normally
 187  */
 188 static inline int scsi_status_is_good(int status)
 189 {
 190         /*
 191          * FIXME: bit0 is listed as reserved in SCSI-2, but is
 192          * significant in SCSI-3.  For now, we follow the SCSI-2
 193          * behaviour and ignore reserved bits.
 194          */
 195         status &= 0xfe;
 196         return ((status == SAM_STAT_GOOD) ||
 197                 (status == SAM_STAT_INTERMEDIATE) ||
 198                 (status == SAM_STAT_INTERMEDIATE_CONDITION_MET) ||
 199                 /* FIXME: this is obsolete in SAM-3 */
 200                 (status == SAM_STAT_COMMAND_TERMINATED));
 201 }
 202
 203 /*
 204  *  Status codes. These are deprecated as they are shifted 1 bit right
 205  *  from those found in the SCSI standards. This causes confusion for
 206  *  applications that are ported to several OSes. Prefer SAM Status codes
 207  *  above.
 208  */
 209
 210 #define GOOD                 0x00
 211 #define CHECK_CONDITION      0x01
 212 #define CONDITION_GOOD       0x02
 213 #define BUSY                 0x04
 214 #define INTERMEDIATE_GOOD    0x08
 215 #define INTERMEDIATE_C_GOOD  0x0a
 216 #define RESERVATION_CONFLICT 0x0c
 217 #define COMMAND_TERMINATED   0x11
 218 #define QUEUE_FULL           0x14
 219 #define ACA_ACTIVE           0x18
 220 #define TASK_ABORTED         0x20
 221
 222 #define STATUS_MASK          0xfe
 223
 224 /*
 225  *  SENSE KEYS
 226  */
 227
 228 #define NO_SENSE            0x00
 229 #define RECOVERED_ERROR     0x01
 230 #define NOT_READY           0x02
 231 #define MEDIUM_ERROR        0x03
 232 #define HARDWARE_ERROR      0x04
 233 #define ILLEGAL_REQUEST     0x05
 234 #define UNIT_ATTENTION      0x06
 235 #define DATA_PROTECT        0x07
 236 #define BLANK_CHECK         0x08
 237 #define COPY_ABORTED        0x0a
 238 #define ABORTED_COMMAND     0x0b
 239 #define VOLUME_OVERFLOW     0x0d
 240 #define MISCOMPARE          0x0e
 241
 242
 243 /*
 244  *  DEVICE TYPES
 245  *  Please keep them in 0x%02x format for $MODALIAS to work
 246  */
 247
 248 #define TYPE_DISK           0x00
 249 #define TYPE_TAPE           0x01
 250 #define TYPE_PRINTER        0x02
 251 #define TYPE_PROCESSOR      0x03    /* HP scanners use this */
 252 #define TYPE_WORM           0x04    /* Treated as ROM by our system */
 253 #define TYPE_ROM            0x05
 254 #define TYPE_SCANNER        0x06
 255 #define TYPE_MOD            0x07    /* Magneto-optical disk -
 256                                      * - treated as TYPE_DISK */
 257 #define TYPE_MEDIUM_CHANGER 0x08
 258 #define TYPE_COMM           0x09    /* Communications device */
 259 #define TYPE_RAID           0x0c
 260 #define TYPE_ENCLOSURE      0x0d    /* Enclosure Services Device */
 261 #define TYPE_RBC            0x0e
 262 #define TYPE_NO_LUN         0x7f
 263
 264 /* SCSI protocols; these are taken from SPC-3 section 7.5 */
 265 enum scsi_protocol {
 266         SCSI_PROTOCOL_FCP = 0,  /* Fibre Channel */
 267         SCSI_PROTOCOL_SPI = 1,  /* parallel SCSI */
 268         SCSI_PROTOCOL_SSA = 2,  /* Serial Storage Architecture - Obsolete */
 269         SCSI_PROTOCOL_SBP = 3,  /* firewire */
 270         SCSI_PROTOCOL_SRP = 4,  /* Infiniband RDMA */
 271         SCSI_PROTOCOL_ISCSI = 5,
 272         SCSI_PROTOCOL_SAS = 6,
 273         SCSI_PROTOCOL_ADT = 7,  /* Media Changers */
 274         SCSI_PROTOCOL_ATA = 8,
 275         SCSI_PROTOCOL_UNSPEC = 0xf, /* No specific protocol */
 276 };
 277
 278 /* Returns a human-readable name for the device */
 279 extern const char * scsi_device_type(unsigned type);
 280
 281 /*
 282  * standard mode-select header prepended to all mode-select commands
 283  */
 284
 285 struct ccs_modesel_head {
 286         __u8 _r1;                       /* reserved */
 287         __u8 medium;            /* device-specific medium type */
 288         __u8 _r2;                       /* reserved */
 289         __u8 block_desc_length; /* block descriptor length */
 290         __u8 density;           /* device-specific density code */
 291         __u8 number_blocks_hi;  /* number of blocks in this block desc */
 292         __u8 number_blocks_med;
 293         __u8 number_blocks_lo;
 294         __u8 _r3;
 295         __u8 block_length_hi;   /* block length for blocks in this desc */
 296         __u8 block_length_med;
 297         __u8 block_length_lo;
 298 };
 299
 300 /*
 301  * ScsiLun: 8 byte LUN.
 302  */
 303 struct scsi_lun {
 304         __u8 scsi_lun[8];
 305 };
 306
 307 /*
 308  *  MESSAGE CODES
 309  */
 310
 311 #define COMMAND_COMPLETE    0x00
 312 #define EXTENDED_MESSAGE    0x01
 313 #define     EXTENDED_MODIFY_DATA_POINTER    0x00
 314 #define     EXTENDED_SDTR                   0x01
 315 #define     EXTENDED_EXTENDED_IDENTIFY      0x02    /* SCSI-I only */
 316 #define     EXTENDED_WDTR                   0x03
 317 #define     EXTENDED_PPR                    0x04
 318 #define     EXTENDED_MODIFY_BIDI_DATA_PTR   0x05
 319 #define SAVE_POINTERS       0x02
 320 #define RESTORE_POINTERS    0x03
 321 #define DISCONNECT          0x04
 322 #define INITIATOR_ERROR     0x05
 323 #define ABORT_TASK_SET      0x06
 324 #define MESSAGE_REJECT      0x07
 325 #define NOP                 0x08
 326 #define MSG_PARITY_ERROR    0x09
 327 #define LINKED_CMD_COMPLETE 0x0a
 328 #define LINKED_FLG_CMD_COMPLETE 0x0b
 329 #define TARGET_RESET        0x0c
 330 #define ABORT_TASK          0x0d
 331 #define CLEAR_TASK_SET      0x0e
 332 #define INITIATE_RECOVERY   0x0f            /* SCSI-II only */
 333 #define RELEASE_RECOVERY    0x10            /* SCSI-II only */
 334 #define CLEAR_ACA           0x16
 335 #define LOGICAL_UNIT_RESET  0x17
 336 #define SIMPLE_QUEUE_TAG    0x20
 337 #define HEAD_OF_QUEUE_TAG   0x21
 338 #define ORDERED_QUEUE_TAG   0x22
 339 #define IGNORE_WIDE_RESIDUE 0x23
 340 #define ACA                 0x24
 341 #define QAS_REQUEST         0x55
 342
 343 /* Old SCSI2 names, don't use in new code */
 344 #define BUS_DEVICE_RESET    TARGET_RESET
 345 #define ABORT               ABORT_TASK_SET
 346
 347 /*
 348  * Host byte codes
 349  */
 350
 351 #define DID_OK          0x00    /* NO error                                */
 352 #define DID_NO_CONNECT  0x01    /* Couldn't connect before timeout period  */
 353 #define DID_BUS_BUSY    0x02    /* BUS stayed busy through time out period */
 354 #define DID_TIME_OUT    0x03    /* TIMED OUT for other reason              */
 355 #define DID_BAD_TARGET  0x04    /* BAD target.                             */
 356 #define DID_ABORT       0x05    /* Told to abort for some other reason     */
 357 #define DID_PARITY      0x06    /* Parity error                            */
 358 #define DID_ERROR       0x07    /* Internal error                          */
 359 #define DID_RESET       0x08    /* Reset by somebody.                      */
 360 #define DID_BAD_INTR    0x09    /* Got an interrupt we weren't expecting.  */
 361 #define DID_PASSTHROUGH 0x0a    /* Force command past mid-layer            */
 362 #define DID_SOFT_ERROR  0x0b    /* The low level driver just wish a retry  */
 363 #define DID_IMM_RETRY   0x0c    /* Retry without decrementing retry count  */
 364 #define DID_REQUEUE     0x0d    /* Requeue command (no immediate retry) also
 365                                  * without decrementing the retry count    */
 366 #define DRIVER_OK       0x00    /* Driver status                           */
 367
 368 /*
 369  *  These indicate the error that occurred, and what is available.
 370  */
 371
 372 #define DRIVER_BUSY         0x01
 373 #define DRIVER_SOFT         0x02
 374 #define DRIVER_MEDIA        0x03
 375 #define DRIVER_ERROR        0x04
 376
 377 #define DRIVER_INVALID      0x05
 378 #define DRIVER_TIMEOUT      0x06
 379 #define DRIVER_HARD         0x07
 380 #define DRIVER_SENSE        0x08
 381
 382 #define SUGGEST_RETRY       0x10
 383 #define SUGGEST_ABORT       0x20
 384 #define SUGGEST_REMAP       0x30
 385 #define SUGGEST_DIE         0x40
 386 #define SUGGEST_SENSE       0x80
 387 #define SUGGEST_IS_OK       0xff
 388
 389 #define DRIVER_MASK         0x0f
 390 #define SUGGEST_MASK        0xf0
 391
 392 /*
 393  * Internal return values.
 394  */
 395
 396 #define NEEDS_RETRY     0x2001
 397 #define SUCCESS         0x2002
 398 #define FAILED          0x2003
 399 #define QUEUED          0x2004
 400 #define SOFT_ERROR      0x2005
 401 #define ADD_TO_MLQUEUE  0x2006
 402 #define TIMEOUT_ERROR   0x2007
 403
 404 /*
 405  * Midlevel queue return values.
 406  */
 407 #define SCSI_MLQUEUE_HOST_BUSY   0x1055
 408 #define SCSI_MLQUEUE_DEVICE_BUSY 0x1056
 409 #define SCSI_MLQUEUE_EH_RETRY    0x1057
 410
 411 /*
 412  *  Use these to separate status msg and our bytes
 413  *
 414  *  These are set by:
 415  *
 416  *      status byte = set from target device
 417  *      msg_byte    = return status from host adapter itself.
 418  *      host_byte   = set by low-level driver to indicate status.
 419  *      driver_byte = set by mid-level.
 420  */
 421 #define status_byte(result) (((result) >> 1) & 0x7f)
 422 #define msg_byte(result)    (((result) >> 8) & 0xff)
 423 #define host_byte(result)   (((result) >> 16) & 0xff)
 424 #define driver_byte(result) (((result) >> 24) & 0xff)
 425 #define suggestion(result)  (driver_byte(result) & SUGGEST_MASK)
 426
 427 #define sense_class(sense)  (((sense) >> 4) & 0x7)
 428 #define sense_error(sense)  ((sense) & 0xf)
 429 #define sense_valid(sense)  ((sense) & 0x80);
 430
 431 /*
 432  * default timeouts
 433 */
 434 #define FORMAT_UNIT_TIMEOUT             (2 * 60 * 60 * HZ)
 435 #define START_STOP_TIMEOUT              (60 * HZ)
 436 #define MOVE_MEDIUM_TIMEOUT             (5 * 60 * HZ)
 437 #define READ_ELEMENT_STATUS_TIMEOUT     (5 * 60 * HZ)
 438 #define READ_DEFECT_DATA_TIMEOUT        (60 * HZ )
 439
 440
 441 #define IDENTIFY_BASE       0x80
 442 #define IDENTIFY(can_disconnect, lun)   (IDENTIFY_BASE |\
 443                      ((can_disconnect) ?  0x40 : 0) |\
 444                      ((lun) & 0x07))
 445
 446 /*
 447  *  struct scsi_device::scsi_level values. For SCSI devices other than those
 448  *  prior to SCSI-2 (i.e. over 12 years old) this value is (resp[2] + 1)
 449  *  where "resp" is a byte array of the response to an INQUIRY. The scsi_level
 450  *  variable is visible to the user via sysfs.
 451  */
 452
 453 #define SCSI_UNKNOWN    0
 454 #define SCSI_1          1
 455 #define SCSI_1_CCS      2
 456 #define SCSI_2          3
 457 #define SCSI_3          4        /* SPC */
 458 #define SCSI_SPC_2      5
 459 #define SCSI_SPC_3      6
 460
 461 /*
 462  * INQ PERIPHERAL QUALIFIERS
 463  */
 464 #define SCSI_INQ_PQ_CON         0x00
 465 #define SCSI_INQ_PQ_NOT_CON     0x01
 466 #define SCSI_INQ_PQ_NOT_CAP     0x03
 467
 468
 469 /*
 470  * Here are some scsi specific ioctl commands which are sometimes useful.
 471  *
 472  * Note that include/linux/cdrom.h also defines IOCTL 0x5300 - 0x5395
 473  */
 474
 475 /* Used to obtain PUN and LUN info.  Conflicts with CDROMAUDIOBUFSIZ */
 476 #define SCSI_IOCTL_GET_IDLUN            0x5382
 477
 478 /* 0x5383 and 0x5384 were used for SCSI_IOCTL_TAGGED_{ENABLE,DISABLE} */
 479
 480 /* Used to obtain the host number of a device. */
 481 #define SCSI_IOCTL_PROBE_HOST           0x5385
 482
 483 /* Used to obtain the bus number for a device */
 484 #define SCSI_IOCTL_GET_BUS_NUMBER       0x5386
 485
 486 /* Used to obtain the PCI location of a device */
 487 #define SCSI_IOCTL_GET_PCI              0x5387
 488
 489 /* Pull a u32 out of a SCSI message (using BE SCSI conventions) */
 490 static inline __u32 scsi_to_u32(__u8 *ptr)
 491 {
 492         return (ptr[0]<<24) + (ptr[1]<<16) + (ptr[2]<<8) + ptr[3];
 493 }
 494
 495 #endif /* _SCSI_SCSI_H */