drivers/scsi/blz2060.c

   1 /* blz2060.c: Driver for Blizzard 2060 SCSI Controller.
   2  *
   3  * Copyright (C) 1996 Jesper Skov (jskov@cygnus.co.uk)
   4  *
   5  * This driver is based on the CyberStorm driver, hence the occasional
   6  * reference to CyberStorm.
   7  */
   8
   9 /* TODO:
  10  *
  11  * 1) Figure out how to make a cleaner merge with the sparc driver with regard
  12  *    to the caches and the Sparc MMU mapping.
  13  * 2) Make as few routines required outside the generic driver. A lot of the
  14  *    routines in this file used to be inline!
  15  */
  16
  17 #include <linux/module.h>
  18
  19 #include <linux/init.h>
  20 #include <linux/kernel.h>
  21 #include <linux/delay.h>
  22 #include <linux/types.h>
  23 #include <linux/string.h>
  24 #include <linux/slab.h>
  25 #include <linux/blkdev.h>
  26 #include <linux/proc_fs.h>
  27 #include <linux/stat.h>
  28 #include <linux/interrupt.h>
  29
  30 #include "scsi.h"
  31 #include <scsi/scsi_host.h>
  32 #include "NCR53C9x.h"
  33
  34 #include <linux/zorro.h>
  35 #include <asm/irq.h>
  36 #include <asm/amigaints.h>
  37 #include <asm/amigahw.h>
  38
  39 #include <asm/pgtable.h>
  40
  41 /* The controller registers can be found in the Z2 config area at these
  42  * offsets:
  43  */
  44 #define BLZ2060_ESP_ADDR 0x1ff00
  45 #define BLZ2060_DMA_ADDR 0x1ffe0
  46
  47
  48 /* The Blizzard 2060 DMA interface
  49  * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  50  * Only two things can be programmed in the Blizzard DMA:
  51  *  1) The data direction is controlled by the status of bit 31 (1 = write)
  52  *  2) The source/dest address (word aligned, shifted one right) in bits 30-0
  53  *
  54  * Figure out interrupt status by reading the ESP status byte.
  55  */
  56 struct blz2060_dma_registers {
  57         volatile unsigned char dma_led_ctrl;    /* DMA led control   [0x000] */
  58         unsigned char dmapad1[0x0f];
  59         volatile unsigned char dma_addr0;       /* DMA address (MSB) [0x010] */
  60         unsigned char dmapad2[0x03];
  61         volatile unsigned char dma_addr1;       /* DMA address       [0x014] */
  62         unsigned char dmapad3[0x03];
  63         volatile unsigned char dma_addr2;       /* DMA address       [0x018] */
  64         unsigned char dmapad4[0x03];
  65         volatile unsigned char dma_addr3;       /* DMA address (LSB) [0x01c] */
  66 };
  67
  68 #define BLZ2060_DMA_WRITE 0x80000000
  69
  70 /* DMA control bits */
  71 #define BLZ2060_DMA_LED    0x02         /* HD led control 1 = off */
  72
  73 static int  dma_bytes_sent(struct NCR_ESP *esp, int fifo_count);
  74 static int  dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp);
  75 static void dma_dump_state(struct NCR_ESP *esp);
  76 static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length);
  77 static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length);
  78 static void dma_ints_off(struct NCR_ESP *esp);
  79 static void dma_ints_on(struct NCR_ESP *esp);
  80 static int  dma_irq_p(struct NCR_ESP *esp);
  81 static void dma_led_off(struct NCR_ESP *esp);
  82 static void dma_led_on(struct NCR_ESP *esp);
  83 static int  dma_ports_p(struct NCR_ESP *esp);
  84 static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write);
  85
  86 static volatile unsigned char cmd_buffer[16];
  87                                 /* This is where all commands are put
  88                                  * before they are transferred to the ESP chip
  89                                  * via PIO.
  90                                  */
  91
  92 /***************************************************************** Detection */
  93 int __init blz2060_esp_detect(struct scsi_host_template *tpnt)
  94 {
  95         struct NCR_ESP *esp;
  96         struct zorro_dev *z = NULL;
  97         unsigned long address;
  98
  99         if ((z = zorro_find_device(ZORRO_PROD_PHASE5_BLIZZARD_2060, z))) {
 100             unsigned long board = z->resource.start;
 101             if (request_mem_region(board+BLZ2060_ESP_ADDR,
 102                                    sizeof(struct ESP_regs), "NCR53C9x")) {
 103                 esp = esp_allocate(tpnt, (void *)board + BLZ2060_ESP_ADDR, 0);
 104
 105                 /* Do command transfer with programmed I/O */
 106                 esp->do_pio_cmds = 1;
 107
 108                 /* Required functions */
 109                 esp->dma_bytes_sent = &dma_bytes_sent;
 110                 esp->dma_can_transfer = &dma_can_transfer;
 111                 esp->dma_dump_state = &dma_dump_state;
 112                 esp->dma_init_read = &dma_init_read;
 113                 esp->dma_init_write = &dma_init_write;
 114                 esp->dma_ints_off = &dma_ints_off;
 115                 esp->dma_ints_on = &dma_ints_on;
 116                 esp->dma_irq_p = &dma_irq_p;
 117                 esp->dma_ports_p = &dma_ports_p;
 118                 esp->dma_setup = &dma_setup;
 119
 120                 /* Optional functions */
 121                 esp->dma_barrier = 0;
 122                 esp->dma_drain = 0;
 123                 esp->dma_invalidate = 0;
 124                 esp->dma_irq_entry = 0;
 125                 esp->dma_irq_exit = 0;
 126                 esp->dma_led_on = &dma_led_on;
 127                 esp->dma_led_off = &dma_led_off;
 128                 esp->dma_poll = 0;
 129                 esp->dma_reset = 0;
 130
 131                 /* SCSI chip speed */
 132                 esp->cfreq = 40000000;
 133
 134                 /* The DMA registers on the Blizzard are mapped
 135                  * relative to the device (i.e. in the same Zorro
 136                  * I/O block).
 137                  */
 138                 address = (unsigned long)ZTWO_VADDR(board);
 139                 esp->dregs = (void *)(address + BLZ2060_DMA_ADDR);
 140
 141                 /* ESP register base */
 142                 esp->eregs = (struct ESP_regs *)(address + BLZ2060_ESP_ADDR);
 143
 144                 /* Set the command buffer */
 145                 esp->esp_command = cmd_buffer;
 146                 esp->esp_command_dvma = virt_to_bus((void *)cmd_buffer);
 147
 148                 esp->irq = IRQ_AMIGA_PORTS;
 149                 request_irq(IRQ_AMIGA_PORTS, esp_intr, IRQF_SHARED,
 150                             "Blizzard 2060 SCSI", esp->ehost);
 151
 152                 /* Figure out our scsi ID on the bus */
 153                 esp->scsi_id = 7;
 154
 155                 /* We don't have a differential SCSI-bus. */
 156                 esp->diff = 0;
 157
 158                 esp_initialize(esp);
 159
 160                 printk("ESP: Total of %d ESP hosts found, %d actually in use.\n", nesps, esps_in_use);
 161                 esps_running = esps_in_use;
 162                 return esps_in_use;
 163             }
 164         }
 165         return 0;
 166 }
 167
 168 /************************************************************* DMA Functions */
 169 static int dma_bytes_sent(struct NCR_ESP *esp, int fifo_count)
 170 {
 171         /* Since the Blizzard DMA is fully dedicated to the ESP chip,
 172          * the number of bytes sent (to the ESP chip) equals the number
 173          * of bytes in the FIFO - there is no buffering in the DMA controller.
 174          * XXXX Do I read this right? It is from host to ESP, right?
 175          */
 176         return fifo_count;
 177 }
 178
 179 static int dma_can_transfer(struct NCR_ESP *esp, Scsi_Cmnd *sp)
 180 {
 181         /* I don't think there's any limit on the Blizzard DMA. So we use what
 182          * the ESP chip can handle (24 bit).
 183          */
 184         unsigned long sz = sp->SCp.this_residual;
 185         if(sz > 0x1000000)
 186                 sz = 0x1000000;
 187         return sz;
 188 }
 189
 190 static void dma_dump_state(struct NCR_ESP *esp)
 191 {
 192         ESPLOG(("intreq:<%04x>, intena:<%04x>\n",
 193                 amiga_custom.intreqr, amiga_custom.intenar));
 194 }
 195
 196 static void dma_init_read(struct NCR_ESP *esp, __u32 addr, int length)
 197 {
 198         struct blz2060_dma_registers *dregs =
 199                 (struct blz2060_dma_registers *) (esp->dregs);
 200
 201         cache_clear(addr, length);
 202
 203         addr >>= 1;
 204         addr &= ~(BLZ2060_DMA_WRITE);
 205         dregs->dma_addr3 = (addr      ) & 0xff;
 206         dregs->dma_addr2 = (addr >>  8) & 0xff;
 207         dregs->dma_addr1 = (addr >> 16) & 0xff;
 208         dregs->dma_addr0 = (addr >> 24) & 0xff;
 209 }
 210
 211 static void dma_init_write(struct NCR_ESP *esp, __u32 addr, int length)
 212 {
 213         struct blz2060_dma_registers *dregs =
 214                 (struct blz2060_dma_registers *) (esp->dregs);
 215
 216         cache_push(addr, length);
 217
 218         addr >>= 1;
 219         addr |= BLZ2060_DMA_WRITE;
 220         dregs->dma_addr3 = (addr      ) & 0xff;
 221         dregs->dma_addr2 = (addr >>  8) & 0xff;
 222         dregs->dma_addr1 = (addr >> 16) & 0xff;
 223         dregs->dma_addr0 = (addr >> 24) & 0xff;
 224 }
 225
 226 static void dma_ints_off(struct NCR_ESP *esp)
 227 {
 228         disable_irq(esp->irq);
 229 }
 230
 231 static void dma_ints_on(struct NCR_ESP *esp)
 232 {
 233         enable_irq(esp->irq);
 234 }
 235
 236 static int dma_irq_p(struct NCR_ESP *esp)
 237 {
 238         return (esp_read(esp->eregs->esp_status) & ESP_STAT_INTR);
 239 }
 240
 241 static void dma_led_off(struct NCR_ESP *esp)
 242 {
 243         ((struct blz2060_dma_registers *) (esp->dregs))->dma_led_ctrl =
 244                 BLZ2060_DMA_LED;
 245 }
 246
 247 static void dma_led_on(struct NCR_ESP *esp)
 248 {
 249         ((struct blz2060_dma_registers *) (esp->dregs))->dma_led_ctrl = 0;
 250 }
 251
 252 static int dma_ports_p(struct NCR_ESP *esp)
 253 {
 254         return ((amiga_custom.intenar) & IF_PORTS);
 255 }
 256
 257 static void dma_setup(struct NCR_ESP *esp, __u32 addr, int count, int write)
 258 {
 259         /* On the Sparc, DMA_ST_WRITE means "move data from device to memory"
 260          * so when (write) is true, it actually means READ!
 261          */
 262         if(write){
 263                 dma_init_read(esp, addr, count);
 264         } else {
 265                 dma_init_write(esp, addr, count);
 266         }
 267 }
 268
 269 #define HOSTS_C
 270
 271 int blz2060_esp_release(struct Scsi_Host *instance)
 272 {
 273 #ifdef MODULE
 274         unsigned long address = (unsigned long)((struct NCR_ESP *)instance->hostdata)->edev;
 275
 276         esp_deallocate((struct NCR_ESP *)instance->hostdata);
 277         esp_release();
 278         release_mem_region(address, sizeof(struct ESP_regs));
 279         free_irq(IRQ_AMIGA_PORTS, esp_intr);
 280 #endif
 281         return 1;
 282 }
 283
 284
 285 static struct scsi_host_template driver_template = {
 286         .proc_name              = "esp-blz2060",
 287         .proc_info              = esp_proc_info,
 288         .name                   = "Blizzard2060 SCSI",
 289         .detect                 = blz2060_esp_detect,
 290         .slave_alloc            = esp_slave_alloc,
 291         .slave_destroy          = esp_slave_destroy,
 292         .release                = blz2060_esp_release,
 293         .queuecommand           = esp_queue,
 294         .eh_abort_handler       = esp_abort,
 295         .eh_bus_reset_handler   = esp_reset,
 296         .can_queue              = 7,
 297         .this_id                = 7,
 298         .sg_tablesize           = SG_ALL,
 299         .cmd_per_lun            = 1,
 300         .use_clustering         = ENABLE_CLUSTERING
 301 };
 302
 303
 304 #include "scsi_module.c"
 305
 306 MODULE_LICENSE("GPL");