arch/mips/au1000/pb1500/board_setup.c

   1 /*
   2  * Copyright 2000 MontaVista Software Inc.
   3  * Author: MontaVista Software, Inc.
   4  *              ppopov@mvista.com or source@mvista.com
   5  *
   6  *  This program is free software; you can redistribute  it and/or modify it
   7  *  under  the terms of  the GNU General  Public License as published by the
   8  *  Free Software Foundation;  either version 2 of the  License, or (at your
   9  *  option) any later version.
  10  *
  11  *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
  12  *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
  13  *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
  14  *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
  15  *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
  16  *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
  17  *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
  18  *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
  19  *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
  20  *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  21  *
  22  *  You should have received a copy of the  GNU General Public License along
  23  *  with this program; if not, write  to the Free Software Foundation, Inc.,
  24  *  675 Mass Ave, Cambridge, MA 02139, USA.
  25  */
  26 #include <linux/config.h>
  27 #include <linux/init.h>
  28 #include <linux/sched.h>
  29 #include <linux/ioport.h>
  30 #include <linux/mm.h>
  31 #include <linux/console.h>
  32 #include <linux/delay.h>
  33
  34 #include <asm/cpu.h>
  35 #include <asm/bootinfo.h>
  36 #include <asm/irq.h>
  37 #include <asm/mipsregs.h>
  38 #include <asm/reboot.h>
  39 #include <asm/pgtable.h>
  40 #include <asm/mach-au1x00/au1000.h>
  41 #include <asm/mach-pb1x00/pb1500.h>
  42
  43 void board_reset (void)
  44 {
  45     /* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
  46     au_writel(0x00000000, 0xAE00001C);
  47 }
  48
  49 void __init board_setup(void)
  50 {
  51         u32 pin_func;
  52         u32 sys_freqctrl, sys_clksrc;
  53
  54         sys_clksrc = sys_freqctrl = pin_func = 0;
  55         // set AUX clock to 12MHz * 8 = 96 MHz
  56         au_writel(8, SYS_AUXPLL);
  57         au_writel(0, SYS_PINSTATERD);
  58         udelay(100);
  59
  60 #if defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE)
  61
  62         /* GPIO201 is input for PCMCIA card detect */
  63         /* GPIO203 is input for PCMCIA interrupt request */
  64         au_writel(au_readl(GPIO2_DIR) & (u32)(~((1<<1)|(1<<3))), GPIO2_DIR);
  65
  66         /* zero and disable FREQ2 */
  67         sys_freqctrl = au_readl(SYS_FREQCTRL0);
  68         sys_freqctrl &= ~0xFFF00000;
  69         au_writel(sys_freqctrl, SYS_FREQCTRL0);
  70
  71         /* zero and disable USBH/USBD clocks */
  72         sys_clksrc = au_readl(SYS_CLKSRC);
  73         sys_clksrc &= ~0x00007FE0;
  74         au_writel(sys_clksrc, SYS_CLKSRC);
  75
  76         sys_freqctrl = au_readl(SYS_FREQCTRL0);
  77         sys_freqctrl &= ~0xFFF00000;
  78
  79         sys_clksrc = au_readl(SYS_CLKSRC);
  80         sys_clksrc &= ~0x00007FE0;
  81
  82         // FREQ2 = aux/2 = 48 MHz
  83         sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
  84         au_writel(sys_freqctrl, SYS_FREQCTRL0);
  85
  86         /*
  87          * Route 48MHz FREQ2 into USB Host and/or Device
  88          */
  89 #ifdef CONFIG_USB_OHCI
  90         sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
  91 #endif
  92 #ifdef CONFIG_AU1X00_USB_DEVICE
  93         sys_clksrc |= ((4<<7) | (0<<6) | (0<<5));
  94 #endif
  95         au_writel(sys_clksrc, SYS_CLKSRC);
  96
  97
  98         pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000);
  99 #ifndef CONFIG_AU1X00_USB_DEVICE
 100         // 2nd USB port is USB host
 101         pin_func |= 0x8000;
 102 #endif
 103         au_writel(pin_func, SYS_PINFUNC);
 104 #endif // defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE)
 105
 106
 107
 108 #ifdef CONFIG_PCI
 109         // Setup PCI bus controller
 110         au_writel(0, Au1500_PCI_CMEM);
 111         au_writel(0x00003fff, Au1500_CFG_BASE);
 112 #if defined(__MIPSEB__)
 113         au_writel(0xf | (2<<6) | (1<<4), Au1500_PCI_CFG);
 114 #else
 115         au_writel(0xf, Au1500_PCI_CFG);
 116 #endif
 117         au_writel(0xf0000000, Au1500_PCI_MWMASK_DEV);
 118         au_writel(0, Au1500_PCI_MWBASE_REV_CCL);
 119         au_writel(0x02a00356, Au1500_PCI_STATCMD);
 120         au_writel(0x00003c04, Au1500_PCI_HDRTYPE);
 121         au_writel(0x00000008, Au1500_PCI_MBAR);
 122         au_sync();
 123 #endif
 124
 125         /* Enable sys bus clock divider when IDLE state or no bus activity. */
 126         au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
 127
 128         /* Enable the RTC if not already enabled */
 129         if (!(au_readl(0xac000028) & 0x20)) {
 130                 printk("enabling clock ...\n");
 131                 au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
 132         }
 133         /* Put the clock in BCD mode */
 134         if (readl(0xac00002C) & 0x4) { /* reg B */
 135                 au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
 136                 au_sync();
 137         }
 138 }