2 * drivers/net/wan/dscc4/dscc4.c: a DSCC4 HDLC driver for Linux
4 * This software may be used and distributed according to the terms of the
5 * GNU General Public License.
7 * The author may be reached as romieu@cogenit.fr.
8 * Specific bug reports/asian food will be welcome.
10 * Special thanks to the nice people at CS-Telecom for the hardware and the
11 * access to the test/measure tools.
16 * I. Board Compatibility
18 * This device driver is designed for the Siemens PEB20534 4 ports serial
19 * controller as found on Etinc PCISYNC cards. The documentation for the
20 * chipset is available at http://www.infineon.com:
21 * - Data Sheet "DSCC4, DMA Supported Serial Communication Controller with
22 * 4 Channels, PEB 20534 Version 2.1, PEF 20534 Version 2.1";
23 * - Application Hint "Management of DSCC4 on-chip FIFO resources".
24 * - Errata sheet DS5 (courtesy of Michael Skerritt).
25 * Jens David has built an adapter based on the same chipset. Take a look
26 * at http://www.afthd.tu-darmstadt.de/~dg1kjd/pciscc4 for a specific
28 * Sample code (2 revisions) is available at Infineon.
30 * II. Board-specific settings
32 * Pcisync can transmit some clock signal to the outside world on the
33 * *first two* ports provided you put a quartz and a line driver on it and
34 * remove the jumpers. The operation is described on Etinc web site. If you
35 * go DCE on these ports, don't forget to use an adequate cable.
37 * Sharing of the PCI interrupt line for this board is possible.
39 * III. Driver operation
41 * The rx/tx operations are based on a linked list of descriptors. The driver
42 * doesn't use HOLD mode any more. HOLD mode is definitely buggy and the more
43 * I tried to fix it, the more it started to look like (convoluted) software
44 * mutation of LxDA method. Errata sheet DS5 suggests to use LxDA: consider
45 * this a rfc2119 MUST.
48 * When the tx ring is full, the xmit routine issues a call to netdev_stop.
49 * The device is supposed to be enabled again during an ALLS irq (we could
50 * use HI but as it's easy to lose events, it's fscked).
53 * The received frames aren't supposed to span over multiple receiving areas.
54 * I may implement it some day but it isn't the highest ranked item.
57 * The current error (XDU, RFO) recovery code is untested.
58 * So far, RDO takes his RX channel down and the right sequence to enable it
59 * again is still a mistery. If RDO happens, plan a reboot. More details
60 * in the code (NB: as this happens, TX still works).
61 * Don't mess the cables during operation, especially on DTE ports. I don't
62 * suggest it for DCE either but at least one can get some messages instead
63 * of a complete instant freeze.
64 * Tests are done on Rev. 20 of the silicium. The RDO handling changes with
65 * the documentation/chipset releases.
69 * - use polling at high irq/s,
70 * - performance analysis,
73 * 2001/12/10 Daniela Squassoni <daniela@cyclades.com>
74 * - Contribution to support the new generic HDLC layer.
77 * - old style interface removal
78 * - dscc4_release_ring fix (related to DMA mapping)
79 * - hard_start_xmit fix (hint: TxSizeMax)
83 #include <linux/module.h>
84 #include <linux/types.h>
85 #include <linux/errno.h>
86 #include <linux/list.h>
87 #include <linux/ioport.h>
88 #include <linux/pci.h>
89 #include <linux/kernel.h>
92 #include <asm/system.h>
93 #include <asm/cache.h>
94 #include <asm/byteorder.h>
95 #include <asm/uaccess.h>
99 #include <linux/init.h>
100 #include <linux/string.h>
102 #include <linux/if_arp.h>
103 #include <linux/netdevice.h>
104 #include <linux/skbuff.h>
105 #include <linux/delay.h>
106 #include <net/syncppp.h>
107 #include <linux/hdlc.h>
110 static const char version
[] = "$Id: dscc4.c,v 1.173 2003/09/20 23:55:34 romieu Exp $ for Linux\n";
114 #ifdef CONFIG_DSCC4_PCI_RST
115 static DECLARE_MUTEX(dscc4_sem
);
116 static u32 dscc4_pci_config_store
[16];
119 #define DRV_NAME "dscc4"
123 /* Module parameters */
125 MODULE_AUTHOR("Maintainer: Francois Romieu <romieu@cogenit.fr>");
126 MODULE_DESCRIPTION("Siemens PEB20534 PCI Controler");
127 MODULE_LICENSE("GPL");
128 module_param(debug
, int, 0);
129 MODULE_PARM_DESC(debug
,"Enable/disable extra messages");
130 module_param(quartz
, int, 0);
131 MODULE_PARM_DESC(quartz
,"If present, on-board quartz frequency (Hz)");
145 u32 jiffies
; /* Allows sizeof(TxFD) == sizeof(RxFD) + extra hack */
156 #define DUMMY_SKB_SIZE 64
158 #define TX_RING_SIZE 32
159 #define RX_RING_SIZE 32
160 #define TX_TOTAL_SIZE TX_RING_SIZE*sizeof(struct TxFD)
161 #define RX_TOTAL_SIZE RX_RING_SIZE*sizeof(struct RxFD)
162 #define IRQ_RING_SIZE 64 /* Keep it a multiple of 32 */
163 #define TX_TIMEOUT (HZ/10)
164 #define DSCC4_HZ_MAX 33000000
165 #define BRR_DIVIDER_MAX 64*0x00004000 /* Cf errata DS5 p.10 */
166 #define dev_per_card 4
167 #define SCC_REGISTERS_MAX 23 /* Cf errata DS5 p.4 */
169 #define SOURCE_ID(flags) (((flags) >> 28) & 0x03)
170 #define TO_SIZE(state) (((state) >> 16) & 0x1fff)
173 * Given the operating range of Linux HDLC, the 2 defines below could be
174 * made simpler. However they are a fine reminder for the limitations of
175 * the driver: it's better to stay < TxSizeMax and < RxSizeMax.
177 #define TO_STATE_TX(len) cpu_to_le32(((len) & TxSizeMax) << 16)
178 #define TO_STATE_RX(len) cpu_to_le32((RX_MAX(len) % RxSizeMax) << 16)
179 #define RX_MAX(len) ((((len) >> 5) + 1) << 5) /* Cf RLCR */
180 #define SCC_REG_START(dpriv) (SCC_START+(dpriv->dev_id)*SCC_OFFSET)
182 struct dscc4_pci_priv
{
186 struct pci_dev
*pdev
;
188 struct dscc4_dev_priv
*root
;
189 dma_addr_t iqcfg_dma
;
193 struct dscc4_dev_priv
{
194 struct sk_buff
*rx_skbuff
[RX_RING_SIZE
];
195 struct sk_buff
*tx_skbuff
[TX_RING_SIZE
];
202 /* FIXME: check all the volatile are required */
203 volatile u32 tx_current
;
208 volatile u32 tx_dirty
;
213 dma_addr_t tx_fd_dma
;
214 dma_addr_t rx_fd_dma
;
218 u32 scc_regs
[SCC_REGISTERS_MAX
]; /* Cf errata DS5 p.4 */
220 struct timer_list timer
;
222 struct dscc4_pci_priv
*pci_priv
;
229 unsigned short encoding
;
230 unsigned short parity
;
231 struct net_device
*dev
;
232 sync_serial_settings settings
;
233 void __iomem
*base_addr
;
234 u32 __pad
__attribute__ ((aligned (4)));
237 /* GLOBAL registers definitions */
258 /* SCC registers definitions */
259 #define SCC_START 0x0100
260 #define SCC_OFFSET 0x80
272 #define GPDATA 0x0404
276 #define EncodingMask 0x00700000
277 #define CrcMask 0x00000003
279 #define IntRxScc0 0x10000000
280 #define IntTxScc0 0x01000000
282 #define TxPollCmd 0x00000400
283 #define RxActivate 0x08000000
284 #define MTFi 0x04000000
285 #define Rdr 0x00400000
286 #define Rdt 0x00200000
287 #define Idr 0x00100000
288 #define Idt 0x00080000
289 #define TxSccRes 0x01000000
290 #define RxSccRes 0x00010000
291 #define TxSizeMax 0x1fff /* Datasheet DS1 - 11.1.1.1 */
292 #define RxSizeMax 0x1ffc /* Datasheet DS1 - 11.1.2.1 */
294 #define Ccr0ClockMask 0x0000003f
295 #define Ccr1LoopMask 0x00000200
296 #define IsrMask 0x000fffff
297 #define BrrExpMask 0x00000f00
298 #define BrrMultMask 0x0000003f
299 #define EncodingMask 0x00700000
300 #define Hold 0x40000000
301 #define SccBusy 0x10000000
302 #define PowerUp 0x80000000
303 #define Vis 0x00001000
304 #define FrameOk (FrameVfr | FrameCrc)
305 #define FrameVfr 0x80
306 #define FrameRdo 0x40
307 #define FrameCrc 0x20
308 #define FrameRab 0x10
309 #define FrameAborted 0x00000200
310 #define FrameEnd 0x80000000
311 #define DataComplete 0x40000000
312 #define LengthCheck 0x00008000
313 #define SccEvt 0x02000000
314 #define NoAck 0x00000200
315 #define Action 0x00000001
316 #define HiDesc 0x20000000
319 #define RxEvt 0xf0000000
320 #define TxEvt 0x0f000000
321 #define Alls 0x00040000
322 #define Xdu 0x00010000
323 #define Cts 0x00004000
324 #define Xmr 0x00002000
325 #define Xpr 0x00001000
326 #define Rdo 0x00000080
327 #define Rfs 0x00000040
328 #define Cd 0x00000004
329 #define Rfo 0x00000002
330 #define Flex 0x00000001
332 /* DMA core events */
333 #define Cfg 0x00200000
334 #define Hi 0x00040000
335 #define Fi 0x00020000
336 #define Err 0x00010000
337 #define Arf 0x00000002
338 #define ArAck 0x00000001
341 #define Ready 0x00000000
342 #define NeedIDR 0x00000001
343 #define NeedIDT 0x00000002
344 #define RdoSet 0x00000004
345 #define FakeReset 0x00000008
347 /* Don't mask RDO. Ever. */
349 #define EventsMask 0xfffeef7f
351 #define EventsMask 0xfffa8f7a
354 /* Functions prototypes */
355 static void dscc4_rx_irq(struct dscc4_pci_priv
*, struct dscc4_dev_priv
*);
356 static void dscc4_tx_irq(struct dscc4_pci_priv
*, struct dscc4_dev_priv
*);
357 static int dscc4_found1(struct pci_dev
*, void __iomem
*ioaddr
);
358 static int dscc4_init_one(struct pci_dev
*, const struct pci_device_id
*ent
);
359 static int dscc4_open(struct net_device
*);
360 static int dscc4_start_xmit(struct sk_buff
*, struct net_device
*);
361 static int dscc4_close(struct net_device
*);
362 static int dscc4_ioctl(struct net_device
*dev
, struct ifreq
*rq
, int cmd
);
363 static int dscc4_init_ring(struct net_device
*);
364 static void dscc4_release_ring(struct dscc4_dev_priv
*);
365 static void dscc4_timer(unsigned long);
366 static void dscc4_tx_timeout(struct net_device
*);
367 static irqreturn_t
dscc4_irq(int irq
, void *dev_id
, struct pt_regs
*ptregs
);
368 static int dscc4_hdlc_attach(struct net_device
*, unsigned short, unsigned short);
369 static int dscc4_set_iface(struct dscc4_dev_priv
*, struct net_device
*);
371 static int dscc4_tx_poll(struct dscc4_dev_priv
*, struct net_device
*);
374 static inline struct dscc4_dev_priv
*dscc4_priv(struct net_device
*dev
)
376 return dev_to_hdlc(dev
)->priv
;
379 static inline struct net_device
*dscc4_to_dev(struct dscc4_dev_priv
*p
)
384 static void scc_patchl(u32 mask
, u32 value
, struct dscc4_dev_priv
*dpriv
,
385 struct net_device
*dev
, int offset
)
389 /* Cf scc_writel for concern regarding thread-safety */
390 state
= dpriv
->scc_regs
[offset
>> 2];
393 dpriv
->scc_regs
[offset
>> 2] = state
;
394 writel(state
, dpriv
->base_addr
+ SCC_REG_START(dpriv
) + offset
);
397 static void scc_writel(u32 bits
, struct dscc4_dev_priv
*dpriv
,
398 struct net_device
*dev
, int offset
)
402 * As of 2002/02/16, there are no thread racing for access.
404 dpriv
->scc_regs
[offset
>> 2] = bits
;
405 writel(bits
, dpriv
->base_addr
+ SCC_REG_START(dpriv
) + offset
);
408 static inline u32
scc_readl(struct dscc4_dev_priv
*dpriv
, int offset
)
410 return dpriv
->scc_regs
[offset
>> 2];
413 static u32
scc_readl_star(struct dscc4_dev_priv
*dpriv
, struct net_device
*dev
)
415 /* Cf errata DS5 p.4 */
416 readl(dpriv
->base_addr
+ SCC_REG_START(dpriv
) + STAR
);
417 return readl(dpriv
->base_addr
+ SCC_REG_START(dpriv
) + STAR
);
420 static inline void dscc4_do_tx(struct dscc4_dev_priv
*dpriv
,
421 struct net_device
*dev
)
423 dpriv
->ltda
= dpriv
->tx_fd_dma
+
424 ((dpriv
->tx_current
-1)%TX_RING_SIZE
)*sizeof(struct TxFD
);
425 writel(dpriv
->ltda
, dpriv
->base_addr
+ CH0LTDA
+ dpriv
->dev_id
*4);
426 /* Flush posted writes *NOW* */
427 readl(dpriv
->base_addr
+ CH0LTDA
+ dpriv
->dev_id
*4);
430 static inline void dscc4_rx_update(struct dscc4_dev_priv
*dpriv
,
431 struct net_device
*dev
)
433 dpriv
->lrda
= dpriv
->rx_fd_dma
+
434 ((dpriv
->rx_dirty
- 1)%RX_RING_SIZE
)*sizeof(struct RxFD
);
435 writel(dpriv
->lrda
, dpriv
->base_addr
+ CH0LRDA
+ dpriv
->dev_id
*4);
438 static inline unsigned int dscc4_tx_done(struct dscc4_dev_priv
*dpriv
)
440 return dpriv
->tx_current
== dpriv
->tx_dirty
;
443 static inline unsigned int dscc4_tx_quiescent(struct dscc4_dev_priv
*dpriv
,
444 struct net_device
*dev
)
446 return readl(dpriv
->base_addr
+ CH0FTDA
+ dpriv
->dev_id
*4) == dpriv
->ltda
;
449 static int state_check(u32 state
, struct dscc4_dev_priv
*dpriv
,
450 struct net_device
*dev
, const char *msg
)
455 if (SOURCE_ID(state
) != dpriv
->dev_id
) {
456 printk(KERN_DEBUG
"%s (%s): Source Id=%d, state=%08x\n",
457 dev
->name
, msg
, SOURCE_ID(state
), state
);
460 if (state
& 0x0df80c00) {
461 printk(KERN_DEBUG
"%s (%s): state=%08x (UFO alert)\n",
462 dev
->name
, msg
, state
);
469 static void dscc4_tx_print(struct net_device
*dev
,
470 struct dscc4_dev_priv
*dpriv
,
473 printk(KERN_DEBUG
"%s: tx_current=%02d tx_dirty=%02d (%s)\n",
474 dev
->name
, dpriv
->tx_current
, dpriv
->tx_dirty
, msg
);
477 static void dscc4_release_ring(struct dscc4_dev_priv
*dpriv
)
479 struct pci_dev
*pdev
= dpriv
->pci_priv
->pdev
;
480 struct TxFD
*tx_fd
= dpriv
->tx_fd
;
481 struct RxFD
*rx_fd
= dpriv
->rx_fd
;
482 struct sk_buff
**skbuff
;
485 pci_free_consistent(pdev
, TX_TOTAL_SIZE
, tx_fd
, dpriv
->tx_fd_dma
);
486 pci_free_consistent(pdev
, RX_TOTAL_SIZE
, rx_fd
, dpriv
->rx_fd_dma
);
488 skbuff
= dpriv
->tx_skbuff
;
489 for (i
= 0; i
< TX_RING_SIZE
; i
++) {
491 pci_unmap_single(pdev
, tx_fd
->data
, (*skbuff
)->len
,
493 dev_kfree_skb(*skbuff
);
499 skbuff
= dpriv
->rx_skbuff
;
500 for (i
= 0; i
< RX_RING_SIZE
; i
++) {
502 pci_unmap_single(pdev
, rx_fd
->data
,
503 RX_MAX(HDLC_MAX_MRU
), PCI_DMA_FROMDEVICE
);
504 dev_kfree_skb(*skbuff
);
511 static inline int try_get_rx_skb(struct dscc4_dev_priv
*dpriv
,
512 struct net_device
*dev
)
514 unsigned int dirty
= dpriv
->rx_dirty
%RX_RING_SIZE
;
515 struct RxFD
*rx_fd
= dpriv
->rx_fd
+ dirty
;
516 const int len
= RX_MAX(HDLC_MAX_MRU
);
520 skb
= dev_alloc_skb(len
);
521 dpriv
->rx_skbuff
[dirty
] = skb
;
523 skb
->protocol
= hdlc_type_trans(skb
, dev
);
524 rx_fd
->data
= pci_map_single(dpriv
->pci_priv
->pdev
, skb
->data
,
525 len
, PCI_DMA_FROMDEVICE
);
527 rx_fd
->data
= (u32
) NULL
;
534 * IRQ/thread/whatever safe
536 static int dscc4_wait_ack_cec(struct dscc4_dev_priv
*dpriv
,
537 struct net_device
*dev
, char *msg
)
542 if (!(scc_readl_star(dpriv
, dev
) & SccBusy
)) {
543 printk(KERN_DEBUG
"%s: %s ack (%d try)\n", dev
->name
,
547 schedule_timeout_uninterruptible(10);
550 printk(KERN_ERR
"%s: %s timeout\n", dev
->name
, msg
);
552 return (i
>= 0) ? i
: -EAGAIN
;
555 static int dscc4_do_action(struct net_device
*dev
, char *msg
)
557 void __iomem
*ioaddr
= dscc4_priv(dev
)->base_addr
;
560 writel(Action
, ioaddr
+ GCMDR
);
563 u32 state
= readl(ioaddr
);
566 printk(KERN_DEBUG
"%s: %s ack\n", dev
->name
, msg
);
567 writel(ArAck
, ioaddr
);
569 } else if (state
& Arf
) {
570 printk(KERN_ERR
"%s: %s failed\n", dev
->name
, msg
);
577 printk(KERN_ERR
"%s: %s timeout\n", dev
->name
, msg
);
582 static inline int dscc4_xpr_ack(struct dscc4_dev_priv
*dpriv
)
584 int cur
= dpriv
->iqtx_current
%IRQ_RING_SIZE
;
588 if (!(dpriv
->flags
& (NeedIDR
| NeedIDT
)) ||
589 (dpriv
->iqtx
[cur
] & Xpr
))
592 schedule_timeout_uninterruptible(10);
595 return (i
>= 0 ) ? i
: -EAGAIN
;
598 #if 0 /* dscc4_{rx/tx}_reset are both unreliable - more tweak needed */
599 static void dscc4_rx_reset(struct dscc4_dev_priv
*dpriv
, struct net_device
*dev
)
603 spin_lock_irqsave(&dpriv
->pci_priv
->lock
, flags
);
604 /* Cf errata DS5 p.6 */
605 writel(0x00000000, dpriv
->base_addr
+ CH0LRDA
+ dpriv
->dev_id
*4);
606 scc_patchl(PowerUp
, 0, dpriv
, dev
, CCR0
);
607 readl(dpriv
->base_addr
+ CH0LRDA
+ dpriv
->dev_id
*4);
608 writel(MTFi
|Rdr
, dpriv
->base_addr
+ dpriv
->dev_id
*0x0c + CH0CFG
);
609 writel(Action
, dpriv
->base_addr
+ GCMDR
);
610 spin_unlock_irqrestore(&dpriv
->pci_priv
->lock
, flags
);
616 static void dscc4_tx_reset(struct dscc4_dev_priv
*dpriv
, struct net_device
*dev
)
620 /* Cf errata DS5 p.7 */
621 scc_patchl(PowerUp
, 0, dpriv
, dev
, CCR0
);
622 scc_writel(0x00050000, dpriv
, dev
, CCR2
);
624 * Must be longer than the time required to fill the fifo.
626 while (!dscc4_tx_quiescent(dpriv
, dev
) && ++i
) {
631 writel(MTFi
|Rdt
, dpriv
->base_addr
+ dpriv
->dev_id
*0x0c + CH0CFG
);
632 if (dscc4_do_action(dev
, "Rdt") < 0)
633 printk(KERN_ERR
"%s: Tx reset failed\n", dev
->name
);
637 /* TODO: (ab)use this function to refill a completely depleted RX ring. */
638 static inline void dscc4_rx_skb(struct dscc4_dev_priv
*dpriv
,
639 struct net_device
*dev
)
641 struct RxFD
*rx_fd
= dpriv
->rx_fd
+ dpriv
->rx_current
%RX_RING_SIZE
;
642 struct net_device_stats
*stats
= hdlc_stats(dev
);
643 struct pci_dev
*pdev
= dpriv
->pci_priv
->pdev
;
647 skb
= dpriv
->rx_skbuff
[dpriv
->rx_current
++%RX_RING_SIZE
];
649 printk(KERN_DEBUG
"%s: skb=0 (%s)\n", dev
->name
, __FUNCTION__
);
652 pkt_len
= TO_SIZE(rx_fd
->state2
);
653 pci_unmap_single(pdev
, rx_fd
->data
, RX_MAX(HDLC_MAX_MRU
), PCI_DMA_FROMDEVICE
);
654 if ((skb
->data
[--pkt_len
] & FrameOk
) == FrameOk
) {
656 stats
->rx_bytes
+= pkt_len
;
657 skb_put(skb
, pkt_len
);
658 if (netif_running(dev
))
659 skb
->protocol
= hdlc_type_trans(skb
, dev
);
660 skb
->dev
->last_rx
= jiffies
;
663 if (skb
->data
[pkt_len
] & FrameRdo
)
664 stats
->rx_fifo_errors
++;
665 else if (!(skb
->data
[pkt_len
] | ~FrameCrc
))
666 stats
->rx_crc_errors
++;
667 else if (!(skb
->data
[pkt_len
] | ~(FrameVfr
| FrameRab
)))
668 stats
->rx_length_errors
++;
671 dev_kfree_skb_irq(skb
);
674 while ((dpriv
->rx_dirty
- dpriv
->rx_current
) % RX_RING_SIZE
) {
675 if (try_get_rx_skb(dpriv
, dev
) < 0)
679 dscc4_rx_update(dpriv
, dev
);
680 rx_fd
->state2
= 0x00000000;
681 rx_fd
->end
= 0xbabeface;
684 static void dscc4_free1(struct pci_dev
*pdev
)
686 struct dscc4_pci_priv
*ppriv
;
687 struct dscc4_dev_priv
*root
;
690 ppriv
= pci_get_drvdata(pdev
);
693 for (i
= 0; i
< dev_per_card
; i
++)
694 unregister_hdlc_device(dscc4_to_dev(root
+ i
));
696 pci_set_drvdata(pdev
, NULL
);
698 for (i
= 0; i
< dev_per_card
; i
++)
699 free_netdev(root
[i
].dev
);
704 static int __devinit
dscc4_init_one(struct pci_dev
*pdev
,
705 const struct pci_device_id
*ent
)
707 struct dscc4_pci_priv
*priv
;
708 struct dscc4_dev_priv
*dpriv
;
709 void __iomem
*ioaddr
;
712 printk(KERN_DEBUG
"%s", version
);
714 rc
= pci_enable_device(pdev
);
718 rc
= pci_request_region(pdev
, 0, "registers");
720 printk(KERN_ERR
"%s: can't reserve MMIO region (regs)\n",
724 rc
= pci_request_region(pdev
, 1, "LBI interface");
726 printk(KERN_ERR
"%s: can't reserve MMIO region (lbi)\n",
728 goto err_free_mmio_region_1
;
731 ioaddr
= ioremap(pci_resource_start(pdev
, 0),
732 pci_resource_len(pdev
, 0));
734 printk(KERN_ERR
"%s: cannot remap MMIO region %lx @ %lx\n",
735 DRV_NAME
, pci_resource_len(pdev
, 0),
736 pci_resource_start(pdev
, 0));
738 goto err_free_mmio_regions_2
;
740 printk(KERN_DEBUG
"Siemens DSCC4, MMIO at %#lx (regs), %#lx (lbi), IRQ %d\n",
741 pci_resource_start(pdev
, 0),
742 pci_resource_start(pdev
, 1), pdev
->irq
);
744 /* Cf errata DS5 p.2 */
745 pci_write_config_byte(pdev
, PCI_LATENCY_TIMER
, 0xf8);
746 pci_set_master(pdev
);
748 rc
= dscc4_found1(pdev
, ioaddr
);
752 priv
= pci_get_drvdata(pdev
);
754 rc
= request_irq(pdev
->irq
, dscc4_irq
, SA_SHIRQ
, DRV_NAME
, priv
->root
);
756 printk(KERN_WARNING
"%s: IRQ %d busy\n", DRV_NAME
, pdev
->irq
);
760 /* power up/little endian/dma core controlled via lrda/ltda */
761 writel(0x00000001, ioaddr
+ GMODE
);
762 /* Shared interrupt queue */
766 bits
= (IRQ_RING_SIZE
>> 5) - 1;
770 writel(bits
, ioaddr
+ IQLENR0
);
772 /* Global interrupt queue */
773 writel((u32
)(((IRQ_RING_SIZE
>> 5) - 1) << 20), ioaddr
+ IQLENR1
);
774 priv
->iqcfg
= (u32
*) pci_alloc_consistent(pdev
,
775 IRQ_RING_SIZE
*sizeof(u32
), &priv
->iqcfg_dma
);
778 writel(priv
->iqcfg_dma
, ioaddr
+ IQCFG
);
783 * SCC 0-3 private rx/tx irq structures
784 * IQRX/TXi needs to be set soon. Learned it the hard way...
786 for (i
= 0; i
< dev_per_card
; i
++) {
787 dpriv
= priv
->root
+ i
;
788 dpriv
->iqtx
= (u32
*) pci_alloc_consistent(pdev
,
789 IRQ_RING_SIZE
*sizeof(u32
), &dpriv
->iqtx_dma
);
791 goto err_free_iqtx_6
;
792 writel(dpriv
->iqtx_dma
, ioaddr
+ IQTX0
+ i
*4);
794 for (i
= 0; i
< dev_per_card
; i
++) {
795 dpriv
= priv
->root
+ i
;
796 dpriv
->iqrx
= (u32
*) pci_alloc_consistent(pdev
,
797 IRQ_RING_SIZE
*sizeof(u32
), &dpriv
->iqrx_dma
);
799 goto err_free_iqrx_7
;
800 writel(dpriv
->iqrx_dma
, ioaddr
+ IQRX0
+ i
*4);
803 /* Cf application hint. Beware of hard-lock condition on threshold. */
804 writel(0x42104000, ioaddr
+ FIFOCR1
);
805 //writel(0x9ce69800, ioaddr + FIFOCR2);
806 writel(0xdef6d800, ioaddr
+ FIFOCR2
);
807 //writel(0x11111111, ioaddr + FIFOCR4);
808 writel(0x18181818, ioaddr
+ FIFOCR4
);
809 // FIXME: should depend on the chipset revision
810 writel(0x0000000e, ioaddr
+ FIFOCR3
);
812 writel(0xff200001, ioaddr
+ GCMDR
);
820 dpriv
= priv
->root
+ i
;
821 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
),
822 dpriv
->iqrx
, dpriv
->iqrx_dma
);
827 dpriv
= priv
->root
+ i
;
828 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
),
829 dpriv
->iqtx
, dpriv
->iqtx_dma
);
831 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
), priv
->iqcfg
,
834 free_irq(pdev
->irq
, priv
->root
);
839 err_free_mmio_regions_2
:
840 pci_release_region(pdev
, 1);
841 err_free_mmio_region_1
:
842 pci_release_region(pdev
, 0);
844 pci_disable_device(pdev
);
849 * Let's hope the default values are decent enough to protect my
850 * feet from the user's gun - Ueimor
852 static void dscc4_init_registers(struct dscc4_dev_priv
*dpriv
,
853 struct net_device
*dev
)
855 /* No interrupts, SCC core disabled. Let's relax */
856 scc_writel(0x00000000, dpriv
, dev
, CCR0
);
858 scc_writel(LengthCheck
| (HDLC_MAX_MRU
>> 5), dpriv
, dev
, RLCR
);
861 * No address recognition/crc-CCITT/cts enabled
862 * Shared flags transmission disabled - cf errata DS5 p.11
863 * Carrier detect disabled - cf errata p.14
864 * FIXME: carrier detection/polarity may be handled more gracefully.
866 scc_writel(0x02408000, dpriv
, dev
, CCR1
);
868 /* crc not forwarded - Cf errata DS5 p.11 */
869 scc_writel(0x00050008 & ~RxActivate
, dpriv
, dev
, CCR2
);
871 //scc_writel(0x00250008 & ~RxActivate, dpriv, dev, CCR2);
874 static inline int dscc4_set_quartz(struct dscc4_dev_priv
*dpriv
, int hz
)
878 if ((hz
< 0) || (hz
> DSCC4_HZ_MAX
))
881 dpriv
->pci_priv
->xtal_hz
= hz
;
886 static int dscc4_found1(struct pci_dev
*pdev
, void __iomem
*ioaddr
)
888 struct dscc4_pci_priv
*ppriv
;
889 struct dscc4_dev_priv
*root
;
890 int i
, ret
= -ENOMEM
;
892 root
= kmalloc(dev_per_card
*sizeof(*root
), GFP_KERNEL
);
894 printk(KERN_ERR
"%s: can't allocate data\n", DRV_NAME
);
897 memset(root
, 0, dev_per_card
*sizeof(*root
));
899 for (i
= 0; i
< dev_per_card
; i
++) {
900 root
[i
].dev
= alloc_hdlcdev(root
+ i
);
905 ppriv
= kmalloc(sizeof(*ppriv
), GFP_KERNEL
);
907 printk(KERN_ERR
"%s: can't allocate private data\n", DRV_NAME
);
910 memset(ppriv
, 0, sizeof(struct dscc4_pci_priv
));
913 spin_lock_init(&ppriv
->lock
);
915 for (i
= 0; i
< dev_per_card
; i
++) {
916 struct dscc4_dev_priv
*dpriv
= root
+ i
;
917 struct net_device
*d
= dscc4_to_dev(dpriv
);
918 hdlc_device
*hdlc
= dev_to_hdlc(d
);
920 d
->base_addr
= (unsigned long)ioaddr
;
923 d
->open
= dscc4_open
;
924 d
->stop
= dscc4_close
;
925 d
->set_multicast_list
= NULL
;
926 d
->do_ioctl
= dscc4_ioctl
;
927 d
->tx_timeout
= dscc4_tx_timeout
;
928 d
->watchdog_timeo
= TX_TIMEOUT
;
930 SET_NETDEV_DEV(d
, &pdev
->dev
);
933 dpriv
->pci_priv
= ppriv
;
934 dpriv
->base_addr
= ioaddr
;
935 spin_lock_init(&dpriv
->lock
);
937 hdlc
->xmit
= dscc4_start_xmit
;
938 hdlc
->attach
= dscc4_hdlc_attach
;
940 dscc4_init_registers(dpriv
, d
);
941 dpriv
->parity
= PARITY_CRC16_PR0_CCITT
;
942 dpriv
->encoding
= ENCODING_NRZ
;
944 ret
= dscc4_init_ring(d
);
948 ret
= register_hdlc_device(d
);
950 printk(KERN_ERR
"%s: unable to register\n", DRV_NAME
);
951 dscc4_release_ring(dpriv
);
956 ret
= dscc4_set_quartz(root
, quartz
);
960 pci_set_drvdata(pdev
, ppriv
);
965 dscc4_release_ring(root
+ i
);
966 unregister_hdlc_device(dscc4_to_dev(root
+ i
));
972 free_netdev(root
[i
].dev
);
978 /* FIXME: get rid of the unneeded code */
979 static void dscc4_timer(unsigned long data
)
981 struct net_device
*dev
= (struct net_device
*)data
;
982 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
983 // struct dscc4_pci_priv *ppriv;
987 dpriv
->timer
.expires
= jiffies
+ TX_TIMEOUT
;
988 add_timer(&dpriv
->timer
);
991 static void dscc4_tx_timeout(struct net_device
*dev
)
993 /* FIXME: something is missing there */
996 static int dscc4_loopback_check(struct dscc4_dev_priv
*dpriv
)
998 sync_serial_settings
*settings
= &dpriv
->settings
;
1000 if (settings
->loopback
&& (settings
->clock_type
!= CLOCK_INT
)) {
1001 struct net_device
*dev
= dscc4_to_dev(dpriv
);
1003 printk(KERN_INFO
"%s: loopback requires clock\n", dev
->name
);
1009 #ifdef CONFIG_DSCC4_PCI_RST
1011 * Some DSCC4-based cards wires the GPIO port and the PCI #RST pin together
1012 * so as to provide a safe way to reset the asic while not the whole machine
1015 * This code doesn't need to be efficient. Keep It Simple
1017 static void dscc4_pci_reset(struct pci_dev
*pdev
, void __iomem
*ioaddr
)
1022 for (i
= 0; i
< 16; i
++)
1023 pci_read_config_dword(pdev
, i
<< 2, dscc4_pci_config_store
+ i
);
1025 /* Maximal LBI clock divider (who cares ?) and whole GPIO range. */
1026 writel(0x001c0000, ioaddr
+ GMODE
);
1027 /* Configure GPIO port as output */
1028 writel(0x0000ffff, ioaddr
+ GPDIR
);
1029 /* Disable interruption */
1030 writel(0x0000ffff, ioaddr
+ GPIM
);
1032 writel(0x0000ffff, ioaddr
+ GPDATA
);
1033 writel(0x00000000, ioaddr
+ GPDATA
);
1035 /* Flush posted writes */
1036 readl(ioaddr
+ GSTAR
);
1038 schedule_timeout_uninterruptible(10);
1040 for (i
= 0; i
< 16; i
++)
1041 pci_write_config_dword(pdev
, i
<< 2, dscc4_pci_config_store
[i
]);
1045 #define dscc4_pci_reset(pdev,ioaddr) do {} while (0)
1046 #endif /* CONFIG_DSCC4_PCI_RST */
1048 static int dscc4_open(struct net_device
*dev
)
1050 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1051 struct dscc4_pci_priv
*ppriv
;
1054 if ((dscc4_loopback_check(dpriv
) < 0) || !dev
->hard_start_xmit
)
1057 if ((ret
= hdlc_open(dev
)))
1060 ppriv
= dpriv
->pci_priv
;
1063 * Due to various bugs, there is no way to reliably reset a
1064 * specific port (manufacturer's dependant special PCI #RST wiring
1065 * apart: it affects all ports). Thus the device goes in the best
1066 * silent mode possible at dscc4_close() time and simply claims to
1067 * be up if it's opened again. It still isn't possible to change
1068 * the HDLC configuration without rebooting but at least the ports
1069 * can be up/down ifconfig'ed without killing the host.
1071 if (dpriv
->flags
& FakeReset
) {
1072 dpriv
->flags
&= ~FakeReset
;
1073 scc_patchl(0, PowerUp
, dpriv
, dev
, CCR0
);
1074 scc_patchl(0, 0x00050000, dpriv
, dev
, CCR2
);
1075 scc_writel(EventsMask
, dpriv
, dev
, IMR
);
1076 printk(KERN_INFO
"%s: up again.\n", dev
->name
);
1080 /* IDT+IDR during XPR */
1081 dpriv
->flags
= NeedIDR
| NeedIDT
;
1083 scc_patchl(0, PowerUp
| Vis
, dpriv
, dev
, CCR0
);
1086 * The following is a bit paranoid...
1088 * NB: the datasheet "...CEC will stay active if the SCC is in
1089 * power-down mode or..." and CCR2.RAC = 1 are two different
1092 if (scc_readl_star(dpriv
, dev
) & SccBusy
) {
1093 printk(KERN_ERR
"%s busy. Try later\n", dev
->name
);
1097 printk(KERN_INFO
"%s: available. Good\n", dev
->name
);
1099 scc_writel(EventsMask
, dpriv
, dev
, IMR
);
1101 /* Posted write is flushed in the wait_ack loop */
1102 scc_writel(TxSccRes
| RxSccRes
, dpriv
, dev
, CMDR
);
1104 if ((ret
= dscc4_wait_ack_cec(dpriv
, dev
, "Cec")) < 0)
1105 goto err_disable_scc_events
;
1108 * I would expect XPR near CE completion (before ? after ?).
1109 * At worst, this code won't see a late XPR and people
1110 * will have to re-issue an ifconfig (this is harmless).
1111 * WARNING, a really missing XPR usually means a hardware
1112 * reset is needed. Suggestions anyone ?
1114 if ((ret
= dscc4_xpr_ack(dpriv
)) < 0) {
1115 printk(KERN_ERR
"%s: %s timeout\n", DRV_NAME
, "XPR");
1116 goto err_disable_scc_events
;
1120 dscc4_tx_print(dev
, dpriv
, "Open");
1123 netif_start_queue(dev
);
1125 init_timer(&dpriv
->timer
);
1126 dpriv
->timer
.expires
= jiffies
+ 10*HZ
;
1127 dpriv
->timer
.data
= (unsigned long)dev
;
1128 dpriv
->timer
.function
= &dscc4_timer
;
1129 add_timer(&dpriv
->timer
);
1130 netif_carrier_on(dev
);
1134 err_disable_scc_events
:
1135 scc_writel(0xffffffff, dpriv
, dev
, IMR
);
1136 scc_patchl(PowerUp
| Vis
, 0, dpriv
, dev
, CCR0
);
1143 #ifdef DSCC4_POLLING
1144 static int dscc4_tx_poll(struct dscc4_dev_priv
*dpriv
, struct net_device
*dev
)
1146 /* FIXME: it's gonna be easy (TM), for sure */
1148 #endif /* DSCC4_POLLING */
1150 static int dscc4_start_xmit(struct sk_buff
*skb
, struct net_device
*dev
)
1152 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1153 struct dscc4_pci_priv
*ppriv
= dpriv
->pci_priv
;
1157 next
= dpriv
->tx_current
%TX_RING_SIZE
;
1158 dpriv
->tx_skbuff
[next
] = skb
;
1159 tx_fd
= dpriv
->tx_fd
+ next
;
1160 tx_fd
->state
= FrameEnd
| TO_STATE_TX(skb
->len
);
1161 tx_fd
->data
= pci_map_single(ppriv
->pdev
, skb
->data
, skb
->len
,
1163 tx_fd
->complete
= 0x00000000;
1164 tx_fd
->jiffies
= jiffies
;
1167 #ifdef DSCC4_POLLING
1168 spin_lock(&dpriv
->lock
);
1169 while (dscc4_tx_poll(dpriv
, dev
));
1170 spin_unlock(&dpriv
->lock
);
1173 dev
->trans_start
= jiffies
;
1176 dscc4_tx_print(dev
, dpriv
, "Xmit");
1177 /* To be cleaned(unsigned int)/optimized. Later, ok ? */
1178 if (!((++dpriv
->tx_current
- dpriv
->tx_dirty
)%TX_RING_SIZE
))
1179 netif_stop_queue(dev
);
1181 if (dscc4_tx_quiescent(dpriv
, dev
))
1182 dscc4_do_tx(dpriv
, dev
);
1187 static int dscc4_close(struct net_device
*dev
)
1189 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1191 del_timer_sync(&dpriv
->timer
);
1192 netif_stop_queue(dev
);
1194 scc_patchl(PowerUp
| Vis
, 0, dpriv
, dev
, CCR0
);
1195 scc_patchl(0x00050000, 0, dpriv
, dev
, CCR2
);
1196 scc_writel(0xffffffff, dpriv
, dev
, IMR
);
1198 dpriv
->flags
|= FakeReset
;
1205 static inline int dscc4_check_clock_ability(int port
)
1209 #ifdef CONFIG_DSCC4_PCISYNC
1217 * DS1 p.137: "There are a total of 13 different clocking modes..."
1220 * - by default, assume a clock is provided on pin RxClk/TxClk (clock mode 0a).
1221 * Clock mode 3b _should_ work but the testing seems to make this point
1222 * dubious (DIY testing requires setting CCR0 at 0x00000033).
1223 * This is supposed to provide least surprise "DTE like" behavior.
1224 * - if line rate is specified, clocks are assumed to be locally generated.
1225 * A quartz must be available (on pin XTAL1). Modes 6b/7b are used. Choosing
1226 * between these it automagically done according on the required frequency
1227 * scaling. Of course some rounding may take place.
1228 * - no high speed mode (40Mb/s). May be trivial to do but I don't have an
1229 * appropriate external clocking device for testing.
1230 * - no time-slot/clock mode 5: shameless lazyness.
1232 * The clock signals wiring can be (is ?) manufacturer dependant. Good luck.
1234 * BIG FAT WARNING: if the device isn't provided enough clocking signal, it
1235 * won't pass the init sequence. For example, straight back-to-back DTE without
1236 * external clock will fail when dscc4_open() (<- 'ifconfig hdlcx xxx') is
1239 * Typos lurk in datasheet (missing divier in clock mode 7a figure 51 p.153
1242 * Clock mode related bits of CCR0:
1243 * +------------ TOE: output TxClk (0b/2b/3a/3b/6b/7a/7b only)
1244 * | +---------- SSEL: sub-mode select 0 -> a, 1 -> b
1245 * | | +-------- High Speed: say 0
1246 * | | | +-+-+-- Clock Mode: 0..7
1249 * x|x|5|4|3|2|1|0| lower bits
1251 * Division factor of BRR: k = (N+1)x2^M (total divider = 16xk in mode 6b)
1252 * +-+-+-+------------------ M (0..15)
1253 * | | | | +-+-+-+-+-+-- N (0..63)
1254 * 0 0 0 0 | | | | 0 0 | | | | | |
1255 * ...-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
1256 * f|e|d|c|b|a|9|8|7|6|5|4|3|2|1|0| lower bits
1259 static int dscc4_set_clock(struct net_device
*dev
, u32
*bps
, u32
*state
)
1261 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1265 *state
&= ~Ccr0ClockMask
;
1266 if (*bps
) { /* Clock generated - required for DCE */
1267 u32 n
= 0, m
= 0, divider
;
1270 xtal
= dpriv
->pci_priv
->xtal_hz
;
1273 if (dscc4_check_clock_ability(dpriv
->dev_id
) < 0)
1275 divider
= xtal
/ *bps
;
1276 if (divider
> BRR_DIVIDER_MAX
) {
1278 *state
|= 0x00000036; /* Clock mode 6b (BRG/16) */
1280 *state
|= 0x00000037; /* Clock mode 7b (BRG) */
1281 if (divider
>> 22) {
1284 } else if (divider
) {
1285 /* Extraction of the 6 highest weighted bits */
1287 while (0xffffffc0 & divider
) {
1295 if (!(*state
& 0x00000001)) /* ?b mode mask => clock mode 6b */
1297 *bps
= xtal
/ divider
;
1300 * External clock - DTE
1301 * "state" already reflects Clock mode 0a (CCR0 = 0xzzzzzz00).
1302 * Nothing more to be done
1306 scc_writel(brr
, dpriv
, dev
, BRR
);
1312 static int dscc4_ioctl(struct net_device
*dev
, struct ifreq
*ifr
, int cmd
)
1314 sync_serial_settings __user
*line
= ifr
->ifr_settings
.ifs_ifsu
.sync
;
1315 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1316 const size_t size
= sizeof(dpriv
->settings
);
1319 if (dev
->flags
& IFF_UP
)
1322 if (cmd
!= SIOCWANDEV
)
1325 switch(ifr
->ifr_settings
.type
) {
1327 ifr
->ifr_settings
.type
= IF_IFACE_SYNC_SERIAL
;
1328 if (ifr
->ifr_settings
.size
< size
) {
1329 ifr
->ifr_settings
.size
= size
; /* data size wanted */
1332 if (copy_to_user(line
, &dpriv
->settings
, size
))
1336 case IF_IFACE_SYNC_SERIAL
:
1337 if (!capable(CAP_NET_ADMIN
))
1340 if (dpriv
->flags
& FakeReset
) {
1341 printk(KERN_INFO
"%s: please reset the device"
1342 " before this command\n", dev
->name
);
1345 if (copy_from_user(&dpriv
->settings
, line
, size
))
1347 ret
= dscc4_set_iface(dpriv
, dev
);
1351 ret
= hdlc_ioctl(dev
, ifr
, cmd
);
1358 static int dscc4_match(struct thingie
*p
, int value
)
1362 for (i
= 0; p
[i
].define
!= -1; i
++) {
1363 if (value
== p
[i
].define
)
1366 if (p
[i
].define
== -1)
1372 static int dscc4_clock_setting(struct dscc4_dev_priv
*dpriv
,
1373 struct net_device
*dev
)
1375 sync_serial_settings
*settings
= &dpriv
->settings
;
1376 int ret
= -EOPNOTSUPP
;
1379 bps
= settings
->clock_rate
;
1380 state
= scc_readl(dpriv
, CCR0
);
1381 if (dscc4_set_clock(dev
, &bps
, &state
) < 0)
1383 if (bps
) { /* DCE */
1384 printk(KERN_DEBUG
"%s: generated RxClk (DCE)\n", dev
->name
);
1385 if (settings
->clock_rate
!= bps
) {
1386 printk(KERN_DEBUG
"%s: clock adjusted (%08d -> %08d)\n",
1387 dev
->name
, settings
->clock_rate
, bps
);
1388 settings
->clock_rate
= bps
;
1391 state
|= PowerUp
| Vis
;
1392 printk(KERN_DEBUG
"%s: external RxClk (DTE)\n", dev
->name
);
1394 scc_writel(state
, dpriv
, dev
, CCR0
);
1400 static int dscc4_encoding_setting(struct dscc4_dev_priv
*dpriv
,
1401 struct net_device
*dev
)
1403 struct thingie encoding
[] = {
1404 { ENCODING_NRZ
, 0x00000000 },
1405 { ENCODING_NRZI
, 0x00200000 },
1406 { ENCODING_FM_MARK
, 0x00400000 },
1407 { ENCODING_FM_SPACE
, 0x00500000 },
1408 { ENCODING_MANCHESTER
, 0x00600000 },
1413 i
= dscc4_match(encoding
, dpriv
->encoding
);
1415 scc_patchl(EncodingMask
, encoding
[i
].bits
, dpriv
, dev
, CCR0
);
1421 static int dscc4_loopback_setting(struct dscc4_dev_priv
*dpriv
,
1422 struct net_device
*dev
)
1424 sync_serial_settings
*settings
= &dpriv
->settings
;
1427 state
= scc_readl(dpriv
, CCR1
);
1428 if (settings
->loopback
) {
1429 printk(KERN_DEBUG
"%s: loopback\n", dev
->name
);
1430 state
|= 0x00000100;
1432 printk(KERN_DEBUG
"%s: normal\n", dev
->name
);
1433 state
&= ~0x00000100;
1435 scc_writel(state
, dpriv
, dev
, CCR1
);
1439 static int dscc4_crc_setting(struct dscc4_dev_priv
*dpriv
,
1440 struct net_device
*dev
)
1442 struct thingie crc
[] = {
1443 { PARITY_CRC16_PR0_CCITT
, 0x00000010 },
1444 { PARITY_CRC16_PR1_CCITT
, 0x00000000 },
1445 { PARITY_CRC32_PR0_CCITT
, 0x00000011 },
1446 { PARITY_CRC32_PR1_CCITT
, 0x00000001 }
1450 i
= dscc4_match(crc
, dpriv
->parity
);
1452 scc_patchl(CrcMask
, crc
[i
].bits
, dpriv
, dev
, CCR1
);
1458 static int dscc4_set_iface(struct dscc4_dev_priv
*dpriv
, struct net_device
*dev
)
1461 int (*action
)(struct dscc4_dev_priv
*, struct net_device
*);
1462 } *p
, do_setting
[] = {
1463 { dscc4_encoding_setting
},
1464 { dscc4_clock_setting
},
1465 { dscc4_loopback_setting
},
1466 { dscc4_crc_setting
},
1471 for (p
= do_setting
; p
->action
; p
++) {
1472 if ((ret
= p
->action(dpriv
, dev
)) < 0)
1478 static irqreturn_t
dscc4_irq(int irq
, void *token
, struct pt_regs
*ptregs
)
1480 struct dscc4_dev_priv
*root
= token
;
1481 struct dscc4_pci_priv
*priv
;
1482 struct net_device
*dev
;
1483 void __iomem
*ioaddr
;
1485 unsigned long flags
;
1488 priv
= root
->pci_priv
;
1489 dev
= dscc4_to_dev(root
);
1491 spin_lock_irqsave(&priv
->lock
, flags
);
1493 ioaddr
= root
->base_addr
;
1495 state
= readl(ioaddr
+ GSTAR
);
1501 printk(KERN_DEBUG
"%s: GSTAR = 0x%08x\n", DRV_NAME
, state
);
1502 writel(state
, ioaddr
+ GSTAR
);
1505 printk(KERN_ERR
"%s: failure (Arf). Harass the maintener\n",
1512 printk(KERN_DEBUG
"%s: CfgIV\n", DRV_NAME
);
1513 if (priv
->iqcfg
[priv
->cfg_cur
++%IRQ_RING_SIZE
] & Arf
)
1514 printk(KERN_ERR
"%s: %s failed\n", dev
->name
, "CFG");
1515 if (!(state
&= ~Cfg
))
1518 if (state
& RxEvt
) {
1519 i
= dev_per_card
- 1;
1521 dscc4_rx_irq(priv
, root
+ i
);
1525 if (state
& TxEvt
) {
1526 i
= dev_per_card
- 1;
1528 dscc4_tx_irq(priv
, root
+ i
);
1533 spin_unlock_irqrestore(&priv
->lock
, flags
);
1534 return IRQ_RETVAL(handled
);
1537 static void dscc4_tx_irq(struct dscc4_pci_priv
*ppriv
,
1538 struct dscc4_dev_priv
*dpriv
)
1540 struct net_device
*dev
= dscc4_to_dev(dpriv
);
1545 cur
= dpriv
->iqtx_current
%IRQ_RING_SIZE
;
1546 state
= dpriv
->iqtx
[cur
];
1549 printk(KERN_DEBUG
"%s: Tx ISR = 0x%08x\n", dev
->name
,
1551 if ((debug
> 1) && (loop
> 1))
1552 printk(KERN_DEBUG
"%s: Tx irq loop=%d\n", dev
->name
, loop
);
1553 if (loop
&& netif_queue_stopped(dev
))
1554 if ((dpriv
->tx_current
- dpriv
->tx_dirty
)%TX_RING_SIZE
)
1555 netif_wake_queue(dev
);
1557 if (netif_running(dev
) && dscc4_tx_quiescent(dpriv
, dev
) &&
1558 !dscc4_tx_done(dpriv
))
1559 dscc4_do_tx(dpriv
, dev
);
1563 dpriv
->iqtx
[cur
] = 0;
1564 dpriv
->iqtx_current
++;
1566 if (state_check(state
, dpriv
, dev
, "Tx") < 0)
1569 if (state
& SccEvt
) {
1571 struct net_device_stats
*stats
= hdlc_stats(dev
);
1572 struct sk_buff
*skb
;
1576 dscc4_tx_print(dev
, dpriv
, "Alls");
1578 * DataComplete can't be trusted for Tx completion.
1581 cur
= dpriv
->tx_dirty
%TX_RING_SIZE
;
1582 tx_fd
= dpriv
->tx_fd
+ cur
;
1583 skb
= dpriv
->tx_skbuff
[cur
];
1585 pci_unmap_single(ppriv
->pdev
, tx_fd
->data
,
1586 skb
->len
, PCI_DMA_TODEVICE
);
1587 if (tx_fd
->state
& FrameEnd
) {
1588 stats
->tx_packets
++;
1589 stats
->tx_bytes
+= skb
->len
;
1591 dev_kfree_skb_irq(skb
);
1592 dpriv
->tx_skbuff
[cur
] = NULL
;
1596 printk(KERN_ERR
"%s Tx: NULL skb %d\n",
1600 * If the driver ends sending crap on the wire, it
1601 * will be way easier to diagnose than the (not so)
1602 * random freeze induced by null sized tx frames.
1604 tx_fd
->data
= tx_fd
->next
;
1605 tx_fd
->state
= FrameEnd
| TO_STATE_TX(2*DUMMY_SKB_SIZE
);
1606 tx_fd
->complete
= 0x00000000;
1609 if (!(state
&= ~Alls
))
1613 * Transmit Data Underrun
1616 printk(KERN_ERR
"%s: XDU. Ask maintainer\n", DRV_NAME
);
1617 dpriv
->flags
= NeedIDT
;
1620 dpriv
->base_addr
+ 0x0c*dpriv
->dev_id
+ CH0CFG
);
1621 writel(Action
, dpriv
->base_addr
+ GCMDR
);
1625 printk(KERN_INFO
"%s: CTS transition\n", dev
->name
);
1626 if (!(state
&= ~Cts
)) /* DEBUG */
1630 /* Frame needs to be sent again - FIXME */
1631 printk(KERN_ERR
"%s: Xmr. Ask maintainer\n", DRV_NAME
);
1632 if (!(state
&= ~Xmr
)) /* DEBUG */
1636 void __iomem
*scc_addr
;
1641 * - the busy condition happens (sometimes);
1642 * - it doesn't seem to make the handler unreliable.
1644 for (i
= 1; i
; i
<<= 1) {
1645 if (!(scc_readl_star(dpriv
, dev
) & SccBusy
))
1649 printk(KERN_INFO
"%s busy in irq\n", dev
->name
);
1651 scc_addr
= dpriv
->base_addr
+ 0x0c*dpriv
->dev_id
;
1652 /* Keep this order: IDT before IDR */
1653 if (dpriv
->flags
& NeedIDT
) {
1655 dscc4_tx_print(dev
, dpriv
, "Xpr");
1656 ring
= dpriv
->tx_fd_dma
+
1657 (dpriv
->tx_dirty
%TX_RING_SIZE
)*
1658 sizeof(struct TxFD
);
1659 writel(ring
, scc_addr
+ CH0BTDA
);
1660 dscc4_do_tx(dpriv
, dev
);
1661 writel(MTFi
| Idt
, scc_addr
+ CH0CFG
);
1662 if (dscc4_do_action(dev
, "IDT") < 0)
1664 dpriv
->flags
&= ~NeedIDT
;
1666 if (dpriv
->flags
& NeedIDR
) {
1667 ring
= dpriv
->rx_fd_dma
+
1668 (dpriv
->rx_current
%RX_RING_SIZE
)*
1669 sizeof(struct RxFD
);
1670 writel(ring
, scc_addr
+ CH0BRDA
);
1671 dscc4_rx_update(dpriv
, dev
);
1672 writel(MTFi
| Idr
, scc_addr
+ CH0CFG
);
1673 if (dscc4_do_action(dev
, "IDR") < 0)
1675 dpriv
->flags
&= ~NeedIDR
;
1677 /* Activate receiver and misc */
1678 scc_writel(0x08050008, dpriv
, dev
, CCR2
);
1681 if (!(state
&= ~Xpr
))
1686 printk(KERN_INFO
"%s: CD transition\n", dev
->name
);
1687 if (!(state
&= ~Cd
)) /* DEBUG */
1690 } else { /* ! SccEvt */
1692 #ifdef DSCC4_POLLING
1693 while (!dscc4_tx_poll(dpriv
, dev
));
1695 printk(KERN_INFO
"%s: Tx Hi\n", dev
->name
);
1699 printk(KERN_INFO
"%s: Tx ERR\n", dev
->name
);
1700 hdlc_stats(dev
)->tx_errors
++;
1707 static void dscc4_rx_irq(struct dscc4_pci_priv
*priv
,
1708 struct dscc4_dev_priv
*dpriv
)
1710 struct net_device
*dev
= dscc4_to_dev(dpriv
);
1715 cur
= dpriv
->iqrx_current
%IRQ_RING_SIZE
;
1716 state
= dpriv
->iqrx
[cur
];
1719 dpriv
->iqrx
[cur
] = 0;
1720 dpriv
->iqrx_current
++;
1722 if (state_check(state
, dpriv
, dev
, "Rx") < 0)
1725 if (!(state
& SccEvt
)){
1729 printk(KERN_DEBUG
"%s: Rx ISR = 0x%08x\n", dev
->name
,
1731 state
&= 0x00ffffff;
1732 if (state
& Err
) { /* Hold or reset */
1733 printk(KERN_DEBUG
"%s: Rx ERR\n", dev
->name
);
1734 cur
= dpriv
->rx_current
%RX_RING_SIZE
;
1735 rx_fd
= dpriv
->rx_fd
+ cur
;
1737 * Presume we're not facing a DMAC receiver reset.
1738 * As We use the rx size-filtering feature of the
1739 * DSCC4, the beginning of a new frame is waiting in
1740 * the rx fifo. I bet a Receive Data Overflow will
1741 * happen most of time but let's try and avoid it.
1742 * Btw (as for RDO) if one experiences ERR whereas
1743 * the system looks rather idle, there may be a
1744 * problem with latency. In this case, increasing
1745 * RX_RING_SIZE may help.
1747 //while (dpriv->rx_needs_refill) {
1748 while (!(rx_fd
->state1
& Hold
)) {
1751 if (!(cur
= cur
%RX_RING_SIZE
))
1752 rx_fd
= dpriv
->rx_fd
;
1754 //dpriv->rx_needs_refill--;
1755 try_get_rx_skb(dpriv
, dev
);
1758 rx_fd
->state1
&= ~Hold
;
1759 rx_fd
->state2
= 0x00000000;
1760 rx_fd
->end
= 0xbabeface;
1765 dscc4_rx_skb(dpriv
, dev
);
1768 if (state
& Hi
) { /* HI bit */
1769 printk(KERN_INFO
"%s: Rx Hi\n", dev
->name
);
1773 } else { /* SccEvt */
1775 //FIXME: verifier la presence de tous les evenements
1778 const char *irq_name
;
1780 { 0x00008000, "TIN"},
1781 { 0x00000020, "RSC"},
1782 { 0x00000010, "PCE"},
1783 { 0x00000008, "PLLA"},
1787 for (evt
= evts
; evt
->irq_name
; evt
++) {
1788 if (state
& evt
->mask
) {
1789 printk(KERN_DEBUG
"%s: %s\n",
1790 dev
->name
, evt
->irq_name
);
1791 if (!(state
&= ~evt
->mask
))
1796 if (!(state
&= ~0x0000c03c))
1800 printk(KERN_INFO
"%s: CTS transition\n", dev
->name
);
1801 if (!(state
&= ~Cts
)) /* DEBUG */
1805 * Receive Data Overflow (FIXME: fscked)
1809 void __iomem
*scc_addr
;
1813 // dscc4_rx_dump(dpriv);
1814 scc_addr
= dpriv
->base_addr
+ 0x0c*dpriv
->dev_id
;
1816 scc_patchl(RxActivate
, 0, dpriv
, dev
, CCR2
);
1818 * This has no effect. Why ?
1819 * ORed with TxSccRes, one sees the CFG ack (for
1820 * the TX part only).
1822 scc_writel(RxSccRes
, dpriv
, dev
, CMDR
);
1823 dpriv
->flags
|= RdoSet
;
1826 * Let's try and save something in the received data.
1827 * rx_current must be incremented at least once to
1828 * avoid HOLD in the BRDA-to-be-pointed desc.
1831 cur
= dpriv
->rx_current
++%RX_RING_SIZE
;
1832 rx_fd
= dpriv
->rx_fd
+ cur
;
1833 if (!(rx_fd
->state2
& DataComplete
))
1835 if (rx_fd
->state2
& FrameAborted
) {
1836 hdlc_stats(dev
)->rx_over_errors
++;
1837 rx_fd
->state1
|= Hold
;
1838 rx_fd
->state2
= 0x00000000;
1839 rx_fd
->end
= 0xbabeface;
1841 dscc4_rx_skb(dpriv
, dev
);
1845 if (dpriv
->flags
& RdoSet
)
1847 "%s: no RDO in Rx data\n", DRV_NAME
);
1849 #ifdef DSCC4_RDO_EXPERIMENTAL_RECOVERY
1851 * FIXME: must the reset be this violent ?
1853 #warning "FIXME: CH0BRDA"
1854 writel(dpriv
->rx_fd_dma
+
1855 (dpriv
->rx_current
%RX_RING_SIZE
)*
1856 sizeof(struct RxFD
), scc_addr
+ CH0BRDA
);
1857 writel(MTFi
|Rdr
|Idr
, scc_addr
+ CH0CFG
);
1858 if (dscc4_do_action(dev
, "RDR") < 0) {
1859 printk(KERN_ERR
"%s: RDO recovery failed(%s)\n",
1863 writel(MTFi
|Idr
, scc_addr
+ CH0CFG
);
1864 if (dscc4_do_action(dev
, "IDR") < 0) {
1865 printk(KERN_ERR
"%s: RDO recovery failed(%s)\n",
1871 scc_patchl(0, RxActivate
, dpriv
, dev
, CCR2
);
1875 printk(KERN_INFO
"%s: CD transition\n", dev
->name
);
1876 if (!(state
&= ~Cd
)) /* DEBUG */
1880 printk(KERN_DEBUG
"%s: Flex. Ttttt...\n", DRV_NAME
);
1881 if (!(state
&= ~Flex
))
1888 * I had expected the following to work for the first descriptor
1889 * (tx_fd->state = 0xc0000000)
1890 * - Hold=1 (don't try and branch to the next descripto);
1891 * - No=0 (I want an empty data section, i.e. size=0);
1892 * - Fe=1 (required by No=0 or we got an Err irq and must reset).
1893 * It failed and locked solid. Thus the introduction of a dummy skb.
1894 * Problem is acknowledged in errata sheet DS5. Joy :o/
1896 static struct sk_buff
*dscc4_init_dummy_skb(struct dscc4_dev_priv
*dpriv
)
1898 struct sk_buff
*skb
;
1900 skb
= dev_alloc_skb(DUMMY_SKB_SIZE
);
1902 int last
= dpriv
->tx_dirty
%TX_RING_SIZE
;
1903 struct TxFD
*tx_fd
= dpriv
->tx_fd
+ last
;
1905 skb
->len
= DUMMY_SKB_SIZE
;
1906 memcpy(skb
->data
, version
, strlen(version
)%DUMMY_SKB_SIZE
);
1907 tx_fd
->state
= FrameEnd
| TO_STATE_TX(DUMMY_SKB_SIZE
);
1908 tx_fd
->data
= pci_map_single(dpriv
->pci_priv
->pdev
, skb
->data
,
1909 DUMMY_SKB_SIZE
, PCI_DMA_TODEVICE
);
1910 dpriv
->tx_skbuff
[last
] = skb
;
1915 static int dscc4_init_ring(struct net_device
*dev
)
1917 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1918 struct pci_dev
*pdev
= dpriv
->pci_priv
->pdev
;
1924 ring
= pci_alloc_consistent(pdev
, RX_TOTAL_SIZE
, &dpriv
->rx_fd_dma
);
1927 dpriv
->rx_fd
= rx_fd
= (struct RxFD
*) ring
;
1929 ring
= pci_alloc_consistent(pdev
, TX_TOTAL_SIZE
, &dpriv
->tx_fd_dma
);
1931 goto err_free_dma_rx
;
1932 dpriv
->tx_fd
= tx_fd
= (struct TxFD
*) ring
;
1934 memset(dpriv
->tx_skbuff
, 0, sizeof(struct sk_buff
*)*TX_RING_SIZE
);
1935 dpriv
->tx_dirty
= 0xffffffff;
1936 i
= dpriv
->tx_current
= 0;
1938 tx_fd
->state
= FrameEnd
| TO_STATE_TX(2*DUMMY_SKB_SIZE
);
1939 tx_fd
->complete
= 0x00000000;
1940 /* FIXME: NULL should be ok - to be tried */
1941 tx_fd
->data
= dpriv
->tx_fd_dma
;
1942 (tx_fd
++)->next
= (u32
)(dpriv
->tx_fd_dma
+
1943 (++i
%TX_RING_SIZE
)*sizeof(*tx_fd
));
1944 } while (i
< TX_RING_SIZE
);
1946 if (dscc4_init_dummy_skb(dpriv
) < 0)
1947 goto err_free_dma_tx
;
1949 memset(dpriv
->rx_skbuff
, 0, sizeof(struct sk_buff
*)*RX_RING_SIZE
);
1950 i
= dpriv
->rx_dirty
= dpriv
->rx_current
= 0;
1952 /* size set by the host. Multiple of 4 bytes please */
1953 rx_fd
->state1
= HiDesc
;
1954 rx_fd
->state2
= 0x00000000;
1955 rx_fd
->end
= 0xbabeface;
1956 rx_fd
->state1
|= TO_STATE_RX(HDLC_MAX_MRU
);
1957 // FIXME: return value verifiee mais traitement suspect
1958 if (try_get_rx_skb(dpriv
, dev
) >= 0)
1960 (rx_fd
++)->next
= (u32
)(dpriv
->rx_fd_dma
+
1961 (++i
%RX_RING_SIZE
)*sizeof(*rx_fd
));
1962 } while (i
< RX_RING_SIZE
);
1967 pci_free_consistent(pdev
, TX_TOTAL_SIZE
, ring
, dpriv
->tx_fd_dma
);
1969 pci_free_consistent(pdev
, RX_TOTAL_SIZE
, rx_fd
, dpriv
->rx_fd_dma
);
1974 static void __devexit
dscc4_remove_one(struct pci_dev
*pdev
)
1976 struct dscc4_pci_priv
*ppriv
;
1977 struct dscc4_dev_priv
*root
;
1978 void __iomem
*ioaddr
;
1981 ppriv
= pci_get_drvdata(pdev
);
1984 ioaddr
= root
->base_addr
;
1986 dscc4_pci_reset(pdev
, ioaddr
);
1988 free_irq(pdev
->irq
, root
);
1989 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
), ppriv
->iqcfg
,
1991 for (i
= 0; i
< dev_per_card
; i
++) {
1992 struct dscc4_dev_priv
*dpriv
= root
+ i
;
1994 dscc4_release_ring(dpriv
);
1995 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
),
1996 dpriv
->iqrx
, dpriv
->iqrx_dma
);
1997 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
),
1998 dpriv
->iqtx
, dpriv
->iqtx_dma
);
2005 pci_release_region(pdev
, 1);
2006 pci_release_region(pdev
, 0);
2008 pci_disable_device(pdev
);
2011 static int dscc4_hdlc_attach(struct net_device
*dev
, unsigned short encoding
,
2012 unsigned short parity
)
2014 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
2016 if (encoding
!= ENCODING_NRZ
&&
2017 encoding
!= ENCODING_NRZI
&&
2018 encoding
!= ENCODING_FM_MARK
&&
2019 encoding
!= ENCODING_FM_SPACE
&&
2020 encoding
!= ENCODING_MANCHESTER
)
2023 if (parity
!= PARITY_NONE
&&
2024 parity
!= PARITY_CRC16_PR0_CCITT
&&
2025 parity
!= PARITY_CRC16_PR1_CCITT
&&
2026 parity
!= PARITY_CRC32_PR0_CCITT
&&
2027 parity
!= PARITY_CRC32_PR1_CCITT
)
2030 dpriv
->encoding
= encoding
;
2031 dpriv
->parity
= parity
;
2036 static int __init
dscc4_setup(char *str
)
2038 int *args
[] = { &debug
, &quartz
, NULL
}, **p
= args
;
2040 while (*p
&& (get_option(&str
, *p
) == 2))
2045 __setup("dscc4.setup=", dscc4_setup
);
2048 static struct pci_device_id dscc4_pci_tbl
[] = {
2049 { PCI_VENDOR_ID_SIEMENS
, PCI_DEVICE_ID_SIEMENS_DSCC4
,
2050 PCI_ANY_ID
, PCI_ANY_ID
, },
2053 MODULE_DEVICE_TABLE(pci
, dscc4_pci_tbl
);
2055 static struct pci_driver dscc4_driver
= {
2057 .id_table
= dscc4_pci_tbl
,
2058 .probe
= dscc4_init_one
,
2059 .remove
= __devexit_p(dscc4_remove_one
),
2062 static int __init
dscc4_init_module(void)
2064 return pci_module_init(&dscc4_driver
);
2067 static void __exit
dscc4_cleanup_module(void)
2069 pci_unregister_driver(&dscc4_driver
);
2072 module_init(dscc4_init_module
);
2073 module_exit(dscc4_cleanup_module
);