V4L/DVB (6715): ivtv: Remove unnecessary register update
[linux-2.6/verdex.git] / drivers / input / serio / hp_sdc.c
blob02b3ad8c082673efaf5e0ee39dd1365c08bae75f
1 /*
2 * HP i8042-based System Device Controller driver.
4 * Copyright (c) 2001 Brian S. Julin
5 * All rights reserved.
7 * Redistribution and use in source and binary forms, with or without
8 * modification, are permitted provided that the following conditions
9 * are met:
10 * 1. Redistributions of source code must retain the above copyright
11 * notice, this list of conditions, and the following disclaimer,
12 * without modification.
13 * 2. The name of the author may not be used to endorse or promote products
14 * derived from this software without specific prior written permission.
16 * Alternatively, this software may be distributed under the terms of the
17 * GNU General Public License ("GPL").
19 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
20 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
21 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
22 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
23 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
24 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
25 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
26 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
27 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
29 * References:
30 * System Device Controller Microprocessor Firmware Theory of Operation
31 * for Part Number 1820-4784 Revision B. Dwg No. A-1820-4784-2
32 * Helge Deller's original hilkbd.c port for PA-RISC.
35 * Driver theory of operation:
37 * hp_sdc_put does all writing to the SDC. ISR can run on a different
38 * CPU than hp_sdc_put, but only one CPU runs hp_sdc_put at a time
39 * (it cannot really benefit from SMP anyway.) A tasket fit this perfectly.
41 * All data coming back from the SDC is sent via interrupt and can be read
42 * fully in the ISR, so there are no latency/throughput problems there.
43 * The problem is with output, due to the slow clock speed of the SDC
44 * compared to the CPU. This should not be too horrible most of the time,
45 * but if used with HIL devices that support the multibyte transfer command,
46 * keeping outbound throughput flowing at the 6500KBps that the HIL is
47 * capable of is more than can be done at HZ=100.
49 * Busy polling for IBF clear wastes CPU cycles and bus cycles. hp_sdc.ibf
50 * is set to 0 when the IBF flag in the status register has cleared. ISR
51 * may do this, and may also access the parts of queued transactions related
52 * to reading data back from the SDC, but otherwise will not touch the
53 * hp_sdc state. Whenever a register is written hp_sdc.ibf is set to 1.
55 * The i8042 write index and the values in the 4-byte input buffer
56 * starting at 0x70 are kept track of in hp_sdc.wi, and .r7[], respectively,
57 * to minimize the amount of IO needed to the SDC. However these values
58 * do not need to be locked since they are only ever accessed by hp_sdc_put.
60 * A timer task schedules the tasklet once per second just to make
61 * sure it doesn't freeze up and to allow for bad reads to time out.
64 #include <linux/hp_sdc.h>
65 #include <linux/errno.h>
66 #include <linux/init.h>
67 #include <linux/module.h>
68 #include <linux/ioport.h>
69 #include <linux/time.h>
70 #include <linux/slab.h>
71 #include <linux/hil.h>
72 #include <asm/io.h>
73 #include <asm/system.h>
75 /* Machine-specific abstraction */
77 #if defined(__hppa__)
78 # include <asm/parisc-device.h>
79 # define sdc_readb(p) gsc_readb(p)
80 # define sdc_writeb(v,p) gsc_writeb((v),(p))
81 #elif defined(__mc68000__)
82 # include <asm/uaccess.h>
83 # define sdc_readb(p) in_8(p)
84 # define sdc_writeb(v,p) out_8((p),(v))
85 #else
86 # error "HIL is not supported on this platform"
87 #endif
89 #define PREFIX "HP SDC: "
91 MODULE_AUTHOR("Brian S. Julin <bri@calyx.com>");
92 MODULE_DESCRIPTION("HP i8042-based SDC Driver");
93 MODULE_LICENSE("Dual BSD/GPL");
95 EXPORT_SYMBOL(hp_sdc_request_timer_irq);
96 EXPORT_SYMBOL(hp_sdc_request_hil_irq);
97 EXPORT_SYMBOL(hp_sdc_request_cooked_irq);
99 EXPORT_SYMBOL(hp_sdc_release_timer_irq);
100 EXPORT_SYMBOL(hp_sdc_release_hil_irq);
101 EXPORT_SYMBOL(hp_sdc_release_cooked_irq);
103 EXPORT_SYMBOL(__hp_sdc_enqueue_transaction);
104 EXPORT_SYMBOL(hp_sdc_enqueue_transaction);
105 EXPORT_SYMBOL(hp_sdc_dequeue_transaction);
107 static hp_i8042_sdc hp_sdc; /* All driver state is kept in here. */
109 /*************** primitives for use in any context *********************/
110 static inline uint8_t hp_sdc_status_in8(void)
112 uint8_t status;
113 unsigned long flags;
115 write_lock_irqsave(&hp_sdc.ibf_lock, flags);
116 status = sdc_readb(hp_sdc.status_io);
117 if (!(status & HP_SDC_STATUS_IBF))
118 hp_sdc.ibf = 0;
119 write_unlock_irqrestore(&hp_sdc.ibf_lock, flags);
121 return status;
124 static inline uint8_t hp_sdc_data_in8(void)
126 return sdc_readb(hp_sdc.data_io);
129 static inline void hp_sdc_status_out8(uint8_t val)
131 unsigned long flags;
133 write_lock_irqsave(&hp_sdc.ibf_lock, flags);
134 hp_sdc.ibf = 1;
135 if ((val & 0xf0) == 0xe0)
136 hp_sdc.wi = 0xff;
137 sdc_writeb(val, hp_sdc.status_io);
138 write_unlock_irqrestore(&hp_sdc.ibf_lock, flags);
141 static inline void hp_sdc_data_out8(uint8_t val)
143 unsigned long flags;
145 write_lock_irqsave(&hp_sdc.ibf_lock, flags);
146 hp_sdc.ibf = 1;
147 sdc_writeb(val, hp_sdc.data_io);
148 write_unlock_irqrestore(&hp_sdc.ibf_lock, flags);
151 /* Care must be taken to only invoke hp_sdc_spin_ibf when
152 * absolutely needed, or in rarely invoked subroutines.
153 * Not only does it waste CPU cycles, it also wastes bus cycles.
155 static inline void hp_sdc_spin_ibf(void)
157 unsigned long flags;
158 rwlock_t *lock;
160 lock = &hp_sdc.ibf_lock;
162 read_lock_irqsave(lock, flags);
163 if (!hp_sdc.ibf) {
164 read_unlock_irqrestore(lock, flags);
165 return;
167 read_unlock(lock);
168 write_lock(lock);
169 while (sdc_readb(hp_sdc.status_io) & HP_SDC_STATUS_IBF)
171 hp_sdc.ibf = 0;
172 write_unlock_irqrestore(lock, flags);
176 /************************ Interrupt context functions ************************/
177 static void hp_sdc_take(int irq, void *dev_id, uint8_t status, uint8_t data)
179 hp_sdc_transaction *curr;
181 read_lock(&hp_sdc.rtq_lock);
182 if (hp_sdc.rcurr < 0) {
183 read_unlock(&hp_sdc.rtq_lock);
184 return;
186 curr = hp_sdc.tq[hp_sdc.rcurr];
187 read_unlock(&hp_sdc.rtq_lock);
189 curr->seq[curr->idx++] = status;
190 curr->seq[curr->idx++] = data;
191 hp_sdc.rqty -= 2;
192 do_gettimeofday(&hp_sdc.rtv);
194 if (hp_sdc.rqty <= 0) {
195 /* All data has been gathered. */
196 if (curr->seq[curr->actidx] & HP_SDC_ACT_SEMAPHORE)
197 if (curr->act.semaphore)
198 up(curr->act.semaphore);
200 if (curr->seq[curr->actidx] & HP_SDC_ACT_CALLBACK)
201 if (curr->act.irqhook)
202 curr->act.irqhook(irq, dev_id, status, data);
204 curr->actidx = curr->idx;
205 curr->idx++;
206 /* Return control of this transaction */
207 write_lock(&hp_sdc.rtq_lock);
208 hp_sdc.rcurr = -1;
209 hp_sdc.rqty = 0;
210 write_unlock(&hp_sdc.rtq_lock);
211 tasklet_schedule(&hp_sdc.task);
215 static irqreturn_t hp_sdc_isr(int irq, void *dev_id)
217 uint8_t status, data;
219 status = hp_sdc_status_in8();
220 /* Read data unconditionally to advance i8042. */
221 data = hp_sdc_data_in8();
223 /* For now we are ignoring these until we get the SDC to behave. */
224 if (((status & 0xf1) == 0x51) && data == 0x82)
225 return IRQ_HANDLED;
227 switch (status & HP_SDC_STATUS_IRQMASK) {
228 case 0: /* This case is not documented. */
229 break;
231 case HP_SDC_STATUS_USERTIMER:
232 case HP_SDC_STATUS_PERIODIC:
233 case HP_SDC_STATUS_TIMER:
234 read_lock(&hp_sdc.hook_lock);
235 if (hp_sdc.timer != NULL)
236 hp_sdc.timer(irq, dev_id, status, data);
237 read_unlock(&hp_sdc.hook_lock);
238 break;
240 case HP_SDC_STATUS_REG:
241 hp_sdc_take(irq, dev_id, status, data);
242 break;
244 case HP_SDC_STATUS_HILCMD:
245 case HP_SDC_STATUS_HILDATA:
246 read_lock(&hp_sdc.hook_lock);
247 if (hp_sdc.hil != NULL)
248 hp_sdc.hil(irq, dev_id, status, data);
249 read_unlock(&hp_sdc.hook_lock);
250 break;
252 case HP_SDC_STATUS_PUP:
253 read_lock(&hp_sdc.hook_lock);
254 if (hp_sdc.pup != NULL)
255 hp_sdc.pup(irq, dev_id, status, data);
256 else
257 printk(KERN_INFO PREFIX "HP SDC reports successful PUP.\n");
258 read_unlock(&hp_sdc.hook_lock);
259 break;
261 default:
262 read_lock(&hp_sdc.hook_lock);
263 if (hp_sdc.cooked != NULL)
264 hp_sdc.cooked(irq, dev_id, status, data);
265 read_unlock(&hp_sdc.hook_lock);
266 break;
269 return IRQ_HANDLED;
273 static irqreturn_t hp_sdc_nmisr(int irq, void *dev_id)
275 int status;
277 status = hp_sdc_status_in8();
278 printk(KERN_WARNING PREFIX "NMI !\n");
280 #if 0
281 if (status & HP_SDC_NMISTATUS_FHS) {
282 read_lock(&hp_sdc.hook_lock);
283 if (hp_sdc.timer != NULL)
284 hp_sdc.timer(irq, dev_id, status, 0);
285 read_unlock(&hp_sdc.hook_lock);
286 } else {
287 /* TODO: pass this on to the HIL handler, or do SAK here? */
288 printk(KERN_WARNING PREFIX "HIL NMI\n");
290 #endif
292 return IRQ_HANDLED;
296 /***************** Kernel (tasklet) context functions ****************/
298 unsigned long hp_sdc_put(void);
300 static void hp_sdc_tasklet(unsigned long foo)
302 write_lock_irq(&hp_sdc.rtq_lock);
304 if (hp_sdc.rcurr >= 0) {
305 struct timeval tv;
307 do_gettimeofday(&tv);
308 if (tv.tv_sec > hp_sdc.rtv.tv_sec)
309 tv.tv_usec += USEC_PER_SEC;
311 if (tv.tv_usec - hp_sdc.rtv.tv_usec > HP_SDC_MAX_REG_DELAY) {
312 hp_sdc_transaction *curr;
313 uint8_t tmp;
315 curr = hp_sdc.tq[hp_sdc.rcurr];
316 /* If this turns out to be a normal failure mode
317 * we'll need to figure out a way to communicate
318 * it back to the application. and be less verbose.
320 printk(KERN_WARNING PREFIX "read timeout (%ius)!\n",
321 tv.tv_usec - hp_sdc.rtv.tv_usec);
322 curr->idx += hp_sdc.rqty;
323 hp_sdc.rqty = 0;
324 tmp = curr->seq[curr->actidx];
325 curr->seq[curr->actidx] |= HP_SDC_ACT_DEAD;
326 if (tmp & HP_SDC_ACT_SEMAPHORE)
327 if (curr->act.semaphore)
328 up(curr->act.semaphore);
330 if (tmp & HP_SDC_ACT_CALLBACK) {
331 /* Note this means that irqhooks may be called
332 * in tasklet/bh context.
334 if (curr->act.irqhook)
335 curr->act.irqhook(0, NULL, 0, 0);
338 curr->actidx = curr->idx;
339 curr->idx++;
340 hp_sdc.rcurr = -1;
343 write_unlock_irq(&hp_sdc.rtq_lock);
344 hp_sdc_put();
347 unsigned long hp_sdc_put(void)
349 hp_sdc_transaction *curr;
350 uint8_t act;
351 int idx, curridx;
353 int limit = 0;
355 write_lock(&hp_sdc.lock);
357 /* If i8042 buffers are full, we cannot do anything that
358 requires output, so we skip to the administrativa. */
359 if (hp_sdc.ibf) {
360 hp_sdc_status_in8();
361 if (hp_sdc.ibf)
362 goto finish;
365 anew:
366 /* See if we are in the middle of a sequence. */
367 if (hp_sdc.wcurr < 0)
368 hp_sdc.wcurr = 0;
369 read_lock_irq(&hp_sdc.rtq_lock);
370 if (hp_sdc.rcurr == hp_sdc.wcurr)
371 hp_sdc.wcurr++;
372 read_unlock_irq(&hp_sdc.rtq_lock);
373 if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN)
374 hp_sdc.wcurr = 0;
375 curridx = hp_sdc.wcurr;
377 if (hp_sdc.tq[curridx] != NULL)
378 goto start;
380 while (++curridx != hp_sdc.wcurr) {
381 if (curridx >= HP_SDC_QUEUE_LEN) {
382 curridx = -1; /* Wrap to top */
383 continue;
385 read_lock_irq(&hp_sdc.rtq_lock);
386 if (hp_sdc.rcurr == curridx) {
387 read_unlock_irq(&hp_sdc.rtq_lock);
388 continue;
390 read_unlock_irq(&hp_sdc.rtq_lock);
391 if (hp_sdc.tq[curridx] != NULL)
392 break; /* Found one. */
394 if (curridx == hp_sdc.wcurr) { /* There's nothing queued to do. */
395 curridx = -1;
397 hp_sdc.wcurr = curridx;
399 start:
401 /* Check to see if the interrupt mask needs to be set. */
402 if (hp_sdc.set_im) {
403 hp_sdc_status_out8(hp_sdc.im | HP_SDC_CMD_SET_IM);
404 hp_sdc.set_im = 0;
405 goto finish;
408 if (hp_sdc.wcurr == -1)
409 goto done;
411 curr = hp_sdc.tq[curridx];
412 idx = curr->actidx;
414 if (curr->actidx >= curr->endidx) {
415 hp_sdc.tq[curridx] = NULL;
416 /* Interleave outbound data between the transactions. */
417 hp_sdc.wcurr++;
418 if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN)
419 hp_sdc.wcurr = 0;
420 goto finish;
423 act = curr->seq[idx];
424 idx++;
426 if (curr->idx >= curr->endidx) {
427 if (act & HP_SDC_ACT_DEALLOC)
428 kfree(curr);
429 hp_sdc.tq[curridx] = NULL;
430 /* Interleave outbound data between the transactions. */
431 hp_sdc.wcurr++;
432 if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN)
433 hp_sdc.wcurr = 0;
434 goto finish;
437 while (act & HP_SDC_ACT_PRECMD) {
438 if (curr->idx != idx) {
439 idx++;
440 act &= ~HP_SDC_ACT_PRECMD;
441 break;
443 hp_sdc_status_out8(curr->seq[idx]);
444 curr->idx++;
445 /* act finished? */
446 if ((act & HP_SDC_ACT_DURING) == HP_SDC_ACT_PRECMD)
447 goto actdone;
448 /* skip quantity field if data-out sequence follows. */
449 if (act & HP_SDC_ACT_DATAOUT)
450 curr->idx++;
451 goto finish;
453 if (act & HP_SDC_ACT_DATAOUT) {
454 int qty;
456 qty = curr->seq[idx];
457 idx++;
458 if (curr->idx - idx < qty) {
459 hp_sdc_data_out8(curr->seq[curr->idx]);
460 curr->idx++;
461 /* act finished? */
462 if (curr->idx - idx >= qty &&
463 (act & HP_SDC_ACT_DURING) == HP_SDC_ACT_DATAOUT)
464 goto actdone;
465 goto finish;
467 idx += qty;
468 act &= ~HP_SDC_ACT_DATAOUT;
469 } else
470 while (act & HP_SDC_ACT_DATAREG) {
471 int mask;
472 uint8_t w7[4];
474 mask = curr->seq[idx];
475 if (idx != curr->idx) {
476 idx++;
477 idx += !!(mask & 1);
478 idx += !!(mask & 2);
479 idx += !!(mask & 4);
480 idx += !!(mask & 8);
481 act &= ~HP_SDC_ACT_DATAREG;
482 break;
485 w7[0] = (mask & 1) ? curr->seq[++idx] : hp_sdc.r7[0];
486 w7[1] = (mask & 2) ? curr->seq[++idx] : hp_sdc.r7[1];
487 w7[2] = (mask & 4) ? curr->seq[++idx] : hp_sdc.r7[2];
488 w7[3] = (mask & 8) ? curr->seq[++idx] : hp_sdc.r7[3];
490 if (hp_sdc.wi > 0x73 || hp_sdc.wi < 0x70 ||
491 w7[hp_sdc.wi - 0x70] == hp_sdc.r7[hp_sdc.wi - 0x70]) {
492 int i = 0;
494 /* Need to point the write index register */
495 while (i < 4 && w7[i] == hp_sdc.r7[i])
496 i++;
498 if (i < 4) {
499 hp_sdc_status_out8(HP_SDC_CMD_SET_D0 + i);
500 hp_sdc.wi = 0x70 + i;
501 goto finish;
504 idx++;
505 if ((act & HP_SDC_ACT_DURING) == HP_SDC_ACT_DATAREG)
506 goto actdone;
508 curr->idx = idx;
509 act &= ~HP_SDC_ACT_DATAREG;
510 break;
513 hp_sdc_data_out8(w7[hp_sdc.wi - 0x70]);
514 hp_sdc.r7[hp_sdc.wi - 0x70] = w7[hp_sdc.wi - 0x70];
515 hp_sdc.wi++; /* write index register autoincrements */
517 int i = 0;
519 while ((i < 4) && w7[i] == hp_sdc.r7[i])
520 i++;
521 if (i >= 4) {
522 curr->idx = idx + 1;
523 if ((act & HP_SDC_ACT_DURING) ==
524 HP_SDC_ACT_DATAREG)
525 goto actdone;
528 goto finish;
530 /* We don't go any further in the command if there is a pending read,
531 because we don't want interleaved results. */
532 read_lock_irq(&hp_sdc.rtq_lock);
533 if (hp_sdc.rcurr >= 0) {
534 read_unlock_irq(&hp_sdc.rtq_lock);
535 goto finish;
537 read_unlock_irq(&hp_sdc.rtq_lock);
540 if (act & HP_SDC_ACT_POSTCMD) {
541 uint8_t postcmd;
543 /* curr->idx should == idx at this point. */
544 postcmd = curr->seq[idx];
545 curr->idx++;
546 if (act & HP_SDC_ACT_DATAIN) {
548 /* Start a new read */
549 hp_sdc.rqty = curr->seq[curr->idx];
550 do_gettimeofday(&hp_sdc.rtv);
551 curr->idx++;
552 /* Still need to lock here in case of spurious irq. */
553 write_lock_irq(&hp_sdc.rtq_lock);
554 hp_sdc.rcurr = curridx;
555 write_unlock_irq(&hp_sdc.rtq_lock);
556 hp_sdc_status_out8(postcmd);
557 goto finish;
559 hp_sdc_status_out8(postcmd);
560 goto actdone;
563 actdone:
564 if (act & HP_SDC_ACT_SEMAPHORE)
565 up(curr->act.semaphore);
566 else if (act & HP_SDC_ACT_CALLBACK)
567 curr->act.irqhook(0,NULL,0,0);
569 if (curr->idx >= curr->endidx) { /* This transaction is over. */
570 if (act & HP_SDC_ACT_DEALLOC)
571 kfree(curr);
572 hp_sdc.tq[curridx] = NULL;
573 } else {
574 curr->actidx = idx + 1;
575 curr->idx = idx + 2;
577 /* Interleave outbound data between the transactions. */
578 hp_sdc.wcurr++;
579 if (hp_sdc.wcurr >= HP_SDC_QUEUE_LEN)
580 hp_sdc.wcurr = 0;
582 finish:
583 /* If by some quirk IBF has cleared and our ISR has run to
584 see that that has happened, do it all again. */
585 if (!hp_sdc.ibf && limit++ < 20)
586 goto anew;
588 done:
589 if (hp_sdc.wcurr >= 0)
590 tasklet_schedule(&hp_sdc.task);
591 write_unlock(&hp_sdc.lock);
593 return 0;
596 /******* Functions called in either user or kernel context ****/
597 int __hp_sdc_enqueue_transaction(hp_sdc_transaction *this)
599 int i;
601 if (this == NULL) {
602 BUG();
603 return -EINVAL;
606 /* Can't have same transaction on queue twice */
607 for (i = 0; i < HP_SDC_QUEUE_LEN; i++)
608 if (hp_sdc.tq[i] == this)
609 goto fail;
611 this->actidx = 0;
612 this->idx = 1;
614 /* Search for empty slot */
615 for (i = 0; i < HP_SDC_QUEUE_LEN; i++)
616 if (hp_sdc.tq[i] == NULL) {
617 hp_sdc.tq[i] = this;
618 tasklet_schedule(&hp_sdc.task);
619 return 0;
622 printk(KERN_WARNING PREFIX "No free slot to add transaction.\n");
623 return -EBUSY;
625 fail:
626 printk(KERN_WARNING PREFIX "Transaction add failed: transaction already queued?\n");
627 return -EINVAL;
630 int hp_sdc_enqueue_transaction(hp_sdc_transaction *this) {
631 unsigned long flags;
632 int ret;
634 write_lock_irqsave(&hp_sdc.lock, flags);
635 ret = __hp_sdc_enqueue_transaction(this);
636 write_unlock_irqrestore(&hp_sdc.lock,flags);
638 return ret;
641 int hp_sdc_dequeue_transaction(hp_sdc_transaction *this)
643 unsigned long flags;
644 int i;
646 write_lock_irqsave(&hp_sdc.lock, flags);
648 /* TODO: don't remove it if it's not done. */
650 for (i = 0; i < HP_SDC_QUEUE_LEN; i++)
651 if (hp_sdc.tq[i] == this)
652 hp_sdc.tq[i] = NULL;
654 write_unlock_irqrestore(&hp_sdc.lock, flags);
655 return 0;
660 /********************** User context functions **************************/
661 int hp_sdc_request_timer_irq(hp_sdc_irqhook *callback)
663 if (callback == NULL || hp_sdc.dev == NULL)
664 return -EINVAL;
666 write_lock_irq(&hp_sdc.hook_lock);
667 if (hp_sdc.timer != NULL) {
668 write_unlock_irq(&hp_sdc.hook_lock);
669 return -EBUSY;
672 hp_sdc.timer = callback;
673 /* Enable interrupts from the timers */
674 hp_sdc.im &= ~HP_SDC_IM_FH;
675 hp_sdc.im &= ~HP_SDC_IM_PT;
676 hp_sdc.im &= ~HP_SDC_IM_TIMERS;
677 hp_sdc.set_im = 1;
678 write_unlock_irq(&hp_sdc.hook_lock);
680 tasklet_schedule(&hp_sdc.task);
682 return 0;
685 int hp_sdc_request_hil_irq(hp_sdc_irqhook *callback)
687 if (callback == NULL || hp_sdc.dev == NULL)
688 return -EINVAL;
690 write_lock_irq(&hp_sdc.hook_lock);
691 if (hp_sdc.hil != NULL) {
692 write_unlock_irq(&hp_sdc.hook_lock);
693 return -EBUSY;
696 hp_sdc.hil = callback;
697 hp_sdc.im &= ~(HP_SDC_IM_HIL | HP_SDC_IM_RESET);
698 hp_sdc.set_im = 1;
699 write_unlock_irq(&hp_sdc.hook_lock);
701 tasklet_schedule(&hp_sdc.task);
703 return 0;
706 int hp_sdc_request_cooked_irq(hp_sdc_irqhook *callback)
708 if (callback == NULL || hp_sdc.dev == NULL)
709 return -EINVAL;
711 write_lock_irq(&hp_sdc.hook_lock);
712 if (hp_sdc.cooked != NULL) {
713 write_unlock_irq(&hp_sdc.hook_lock);
714 return -EBUSY;
717 /* Enable interrupts from the HIL MLC */
718 hp_sdc.cooked = callback;
719 hp_sdc.im &= ~(HP_SDC_IM_HIL | HP_SDC_IM_RESET);
720 hp_sdc.set_im = 1;
721 write_unlock_irq(&hp_sdc.hook_lock);
723 tasklet_schedule(&hp_sdc.task);
725 return 0;
728 int hp_sdc_release_timer_irq(hp_sdc_irqhook *callback)
730 write_lock_irq(&hp_sdc.hook_lock);
731 if ((callback != hp_sdc.timer) ||
732 (hp_sdc.timer == NULL)) {
733 write_unlock_irq(&hp_sdc.hook_lock);
734 return -EINVAL;
737 /* Disable interrupts from the timers */
738 hp_sdc.timer = NULL;
739 hp_sdc.im |= HP_SDC_IM_TIMERS;
740 hp_sdc.im |= HP_SDC_IM_FH;
741 hp_sdc.im |= HP_SDC_IM_PT;
742 hp_sdc.set_im = 1;
743 write_unlock_irq(&hp_sdc.hook_lock);
744 tasklet_schedule(&hp_sdc.task);
746 return 0;
749 int hp_sdc_release_hil_irq(hp_sdc_irqhook *callback)
751 write_lock_irq(&hp_sdc.hook_lock);
752 if ((callback != hp_sdc.hil) ||
753 (hp_sdc.hil == NULL)) {
754 write_unlock_irq(&hp_sdc.hook_lock);
755 return -EINVAL;
758 hp_sdc.hil = NULL;
759 /* Disable interrupts from HIL only if there is no cooked driver. */
760 if(hp_sdc.cooked == NULL) {
761 hp_sdc.im |= (HP_SDC_IM_HIL | HP_SDC_IM_RESET);
762 hp_sdc.set_im = 1;
764 write_unlock_irq(&hp_sdc.hook_lock);
765 tasklet_schedule(&hp_sdc.task);
767 return 0;
770 int hp_sdc_release_cooked_irq(hp_sdc_irqhook *callback)
772 write_lock_irq(&hp_sdc.hook_lock);
773 if ((callback != hp_sdc.cooked) ||
774 (hp_sdc.cooked == NULL)) {
775 write_unlock_irq(&hp_sdc.hook_lock);
776 return -EINVAL;
779 hp_sdc.cooked = NULL;
780 /* Disable interrupts from HIL only if there is no raw HIL driver. */
781 if(hp_sdc.hil == NULL) {
782 hp_sdc.im |= (HP_SDC_IM_HIL | HP_SDC_IM_RESET);
783 hp_sdc.set_im = 1;
785 write_unlock_irq(&hp_sdc.hook_lock);
786 tasklet_schedule(&hp_sdc.task);
788 return 0;
791 /************************* Keepalive timer task *********************/
793 void hp_sdc_kicker (unsigned long data)
795 tasklet_schedule(&hp_sdc.task);
796 /* Re-insert the periodic task. */
797 mod_timer(&hp_sdc.kicker, jiffies + HZ);
800 /************************** Module Initialization ***************************/
802 #if defined(__hppa__)
804 static const struct parisc_device_id hp_sdc_tbl[] = {
806 .hw_type = HPHW_FIO,
807 .hversion_rev = HVERSION_REV_ANY_ID,
808 .hversion = HVERSION_ANY_ID,
809 .sversion = 0x73,
811 { 0, }
814 MODULE_DEVICE_TABLE(parisc, hp_sdc_tbl);
816 static int __init hp_sdc_init_hppa(struct parisc_device *d);
818 static struct parisc_driver hp_sdc_driver = {
819 .name = "hp_sdc",
820 .id_table = hp_sdc_tbl,
821 .probe = hp_sdc_init_hppa,
824 #endif /* __hppa__ */
826 static int __init hp_sdc_init(void)
828 char *errstr;
829 hp_sdc_transaction t_sync;
830 uint8_t ts_sync[6];
831 struct semaphore s_sync;
833 rwlock_init(&hp_sdc.lock);
834 rwlock_init(&hp_sdc.ibf_lock);
835 rwlock_init(&hp_sdc.rtq_lock);
836 rwlock_init(&hp_sdc.hook_lock);
838 hp_sdc.timer = NULL;
839 hp_sdc.hil = NULL;
840 hp_sdc.pup = NULL;
841 hp_sdc.cooked = NULL;
842 hp_sdc.im = HP_SDC_IM_MASK; /* Mask maskable irqs */
843 hp_sdc.set_im = 1;
844 hp_sdc.wi = 0xff;
845 hp_sdc.r7[0] = 0xff;
846 hp_sdc.r7[1] = 0xff;
847 hp_sdc.r7[2] = 0xff;
848 hp_sdc.r7[3] = 0xff;
849 hp_sdc.ibf = 1;
851 memset(&hp_sdc.tq, 0, sizeof(hp_sdc.tq));
853 hp_sdc.wcurr = -1;
854 hp_sdc.rcurr = -1;
855 hp_sdc.rqty = 0;
857 hp_sdc.dev_err = -ENODEV;
859 errstr = "IO not found for";
860 if (!hp_sdc.base_io)
861 goto err0;
863 errstr = "IRQ not found for";
864 if (!hp_sdc.irq)
865 goto err0;
867 hp_sdc.dev_err = -EBUSY;
869 #if defined(__hppa__)
870 errstr = "IO not available for";
871 if (request_region(hp_sdc.data_io, 2, hp_sdc_driver.name))
872 goto err0;
873 #endif
875 errstr = "IRQ not available for";
876 if (request_irq(hp_sdc.irq, &hp_sdc_isr, IRQF_SHARED|IRQF_SAMPLE_RANDOM,
877 "HP SDC", &hp_sdc))
878 goto err1;
880 errstr = "NMI not available for";
881 if (request_irq(hp_sdc.nmi, &hp_sdc_nmisr, IRQF_SHARED,
882 "HP SDC NMI", &hp_sdc))
883 goto err2;
885 printk(KERN_INFO PREFIX "HP SDC at 0x%p, IRQ %d (NMI IRQ %d)\n",
886 (void *)hp_sdc.base_io, hp_sdc.irq, hp_sdc.nmi);
888 hp_sdc_status_in8();
889 hp_sdc_data_in8();
891 tasklet_init(&hp_sdc.task, hp_sdc_tasklet, 0);
893 /* Sync the output buffer registers, thus scheduling hp_sdc_tasklet. */
894 t_sync.actidx = 0;
895 t_sync.idx = 1;
896 t_sync.endidx = 6;
897 t_sync.seq = ts_sync;
898 ts_sync[0] = HP_SDC_ACT_DATAREG | HP_SDC_ACT_SEMAPHORE;
899 ts_sync[1] = 0x0f;
900 ts_sync[2] = ts_sync[3] = ts_sync[4] = ts_sync[5] = 0;
901 t_sync.act.semaphore = &s_sync;
902 init_MUTEX_LOCKED(&s_sync);
903 hp_sdc_enqueue_transaction(&t_sync);
904 down(&s_sync); /* Wait for t_sync to complete */
906 /* Create the keepalive task */
907 init_timer(&hp_sdc.kicker);
908 hp_sdc.kicker.expires = jiffies + HZ;
909 hp_sdc.kicker.function = &hp_sdc_kicker;
910 add_timer(&hp_sdc.kicker);
912 hp_sdc.dev_err = 0;
913 return 0;
914 err2:
915 free_irq(hp_sdc.irq, &hp_sdc);
916 err1:
917 release_region(hp_sdc.data_io, 2);
918 err0:
919 printk(KERN_WARNING PREFIX ": %s SDC IO=0x%p IRQ=0x%x NMI=0x%x\n",
920 errstr, (void *)hp_sdc.base_io, hp_sdc.irq, hp_sdc.nmi);
921 hp_sdc.dev = NULL;
923 return hp_sdc.dev_err;
926 #if defined(__hppa__)
928 static int __init hp_sdc_init_hppa(struct parisc_device *d)
930 if (!d)
931 return 1;
932 if (hp_sdc.dev != NULL)
933 return 1; /* We only expect one SDC */
935 hp_sdc.dev = d;
936 hp_sdc.irq = d->irq;
937 hp_sdc.nmi = d->aux_irq;
938 hp_sdc.base_io = d->hpa.start;
939 hp_sdc.data_io = d->hpa.start + 0x800;
940 hp_sdc.status_io = d->hpa.start + 0x801;
942 return hp_sdc_init();
945 #endif /* __hppa__ */
947 static void hp_sdc_exit(void)
949 write_lock_irq(&hp_sdc.lock);
951 /* Turn off all maskable "sub-function" irq's. */
952 hp_sdc_spin_ibf();
953 sdc_writeb(HP_SDC_CMD_SET_IM | HP_SDC_IM_MASK, hp_sdc.status_io);
955 /* Wait until we know this has been processed by the i8042 */
956 hp_sdc_spin_ibf();
958 free_irq(hp_sdc.nmi, &hp_sdc);
959 free_irq(hp_sdc.irq, &hp_sdc);
960 write_unlock_irq(&hp_sdc.lock);
962 del_timer(&hp_sdc.kicker);
964 tasklet_kill(&hp_sdc.task);
966 #if defined(__hppa__)
967 if (unregister_parisc_driver(&hp_sdc_driver))
968 printk(KERN_WARNING PREFIX "Error unregistering HP SDC");
969 #endif
972 static int __init hp_sdc_register(void)
974 hp_sdc_transaction tq_init;
975 uint8_t tq_init_seq[5];
976 struct semaphore tq_init_sem;
977 #if defined(__mc68000__)
978 mm_segment_t fs;
979 unsigned char i;
980 #endif
982 hp_sdc.dev = NULL;
983 hp_sdc.dev_err = 0;
984 #if defined(__hppa__)
985 if (register_parisc_driver(&hp_sdc_driver)) {
986 printk(KERN_WARNING PREFIX "Error registering SDC with system bus tree.\n");
987 return -ENODEV;
989 #elif defined(__mc68000__)
990 if (!MACH_IS_HP300)
991 return -ENODEV;
993 hp_sdc.irq = 1;
994 hp_sdc.nmi = 7;
995 hp_sdc.base_io = (unsigned long) 0xf0428000;
996 hp_sdc.data_io = (unsigned long) hp_sdc.base_io + 1;
997 hp_sdc.status_io = (unsigned long) hp_sdc.base_io + 3;
998 fs = get_fs();
999 set_fs(KERNEL_DS);
1000 if (!get_user(i, (unsigned char *)hp_sdc.data_io))
1001 hp_sdc.dev = (void *)1;
1002 set_fs(fs);
1003 hp_sdc.dev_err = hp_sdc_init();
1004 #endif
1005 if (hp_sdc.dev == NULL) {
1006 printk(KERN_WARNING PREFIX "No SDC found.\n");
1007 return hp_sdc.dev_err;
1010 init_MUTEX_LOCKED(&tq_init_sem);
1012 tq_init.actidx = 0;
1013 tq_init.idx = 1;
1014 tq_init.endidx = 5;
1015 tq_init.seq = tq_init_seq;
1016 tq_init.act.semaphore = &tq_init_sem;
1018 tq_init_seq[0] =
1019 HP_SDC_ACT_POSTCMD | HP_SDC_ACT_DATAIN | HP_SDC_ACT_SEMAPHORE;
1020 tq_init_seq[1] = HP_SDC_CMD_READ_KCC;
1021 tq_init_seq[2] = 1;
1022 tq_init_seq[3] = 0;
1023 tq_init_seq[4] = 0;
1025 hp_sdc_enqueue_transaction(&tq_init);
1027 down(&tq_init_sem);
1028 up(&tq_init_sem);
1030 if ((tq_init_seq[0] & HP_SDC_ACT_DEAD) == HP_SDC_ACT_DEAD) {
1031 printk(KERN_WARNING PREFIX "Error reading config byte.\n");
1032 hp_sdc_exit();
1033 return -ENODEV;
1035 hp_sdc.r11 = tq_init_seq[4];
1036 if (hp_sdc.r11 & HP_SDC_CFG_NEW) {
1037 const char *str;
1038 printk(KERN_INFO PREFIX "New style SDC\n");
1039 tq_init_seq[1] = HP_SDC_CMD_READ_XTD;
1040 tq_init.actidx = 0;
1041 tq_init.idx = 1;
1042 down(&tq_init_sem);
1043 hp_sdc_enqueue_transaction(&tq_init);
1044 down(&tq_init_sem);
1045 up(&tq_init_sem);
1046 if ((tq_init_seq[0] & HP_SDC_ACT_DEAD) == HP_SDC_ACT_DEAD) {
1047 printk(KERN_WARNING PREFIX "Error reading extended config byte.\n");
1048 return -ENODEV;
1050 hp_sdc.r7e = tq_init_seq[4];
1051 HP_SDC_XTD_REV_STRINGS(hp_sdc.r7e & HP_SDC_XTD_REV, str)
1052 printk(KERN_INFO PREFIX "Revision: %s\n", str);
1053 if (hp_sdc.r7e & HP_SDC_XTD_BEEPER)
1054 printk(KERN_INFO PREFIX "TI SN76494 beeper present\n");
1055 if (hp_sdc.r7e & HP_SDC_XTD_BBRTC)
1056 printk(KERN_INFO PREFIX "OKI MSM-58321 BBRTC present\n");
1057 printk(KERN_INFO PREFIX "Spunking the self test register to force PUP "
1058 "on next firmware reset.\n");
1059 tq_init_seq[0] = HP_SDC_ACT_PRECMD |
1060 HP_SDC_ACT_DATAOUT | HP_SDC_ACT_SEMAPHORE;
1061 tq_init_seq[1] = HP_SDC_CMD_SET_STR;
1062 tq_init_seq[2] = 1;
1063 tq_init_seq[3] = 0;
1064 tq_init.actidx = 0;
1065 tq_init.idx = 1;
1066 tq_init.endidx = 4;
1067 down(&tq_init_sem);
1068 hp_sdc_enqueue_transaction(&tq_init);
1069 down(&tq_init_sem);
1070 up(&tq_init_sem);
1071 } else
1072 printk(KERN_INFO PREFIX "Old style SDC (1820-%s).\n",
1073 (hp_sdc.r11 & HP_SDC_CFG_REV) ? "3300" : "2564/3087");
1075 return 0;
1078 module_init(hp_sdc_register);
1079 module_exit(hp_sdc_exit);
1081 /* Timing notes: These measurements taken on my 64MHz 7100-LC (715/64)
1082 * cycles cycles-adj time
1083 * between two consecutive mfctl(16)'s: 4 n/a 63ns
1084 * hp_sdc_spin_ibf when idle: 119 115 1.7us
1085 * gsc_writeb status register: 83 79 1.2us
1086 * IBF to clear after sending SET_IM: 6204 6006 93us
1087 * IBF to clear after sending LOAD_RT: 4467 4352 68us
1088 * IBF to clear after sending two LOAD_RTs: 18974 18859 295us
1089 * READ_T1, read status/data, IRQ, call handler: 35564 n/a 556us
1090 * cmd to ~IBF READ_T1 2nd time right after: 5158403 n/a 81ms
1091 * between IRQ received and ~IBF for above: 2578877 n/a 40ms
1093 * Performance stats after a run of this module configuring HIL and
1094 * receiving a few mouse events:
1096 * status in8 282508 cycles 7128 calls
1097 * status out8 8404 cycles 341 calls
1098 * data out8 1734 cycles 78 calls
1099 * isr 174324 cycles 617 calls (includes take)
1100 * take 1241 cycles 2 calls
1101 * put 1411504 cycles 6937 calls
1102 * task 1655209 cycles 6937 calls (includes put)