V4L/DVB (6715): ivtv: Remove unnecessary register update

[linux-2.6/verdex.git] / drivers / video / sa1100fb.c

/*
 *  linux/drivers/video/sa1100fb.c
 *
 *  Copyright (C) 1999 Eric A. Thomas
 *   Based on acornfb.c Copyright (C) Russell King.
 *
 * This file is subject to the terms and conditions of the GNU General Public
 * License.  See the file COPYING in the main directory of this archive for
 * more details.
 *
 *              StrongARM 1100 LCD Controller Frame Buffer Driver
 *
 * Please direct your questions and comments on this driver to the following
 * email address:
 *
 *      linux-arm-kernel@lists.arm.linux.org.uk
 *
 * Clean patches should be sent to the ARM Linux Patch System.  Please see the
 * following web page for more information:
 *
 *      http://www.arm.linux.org.uk/developer/patches/info.shtml
 *
 * Thank you.
 *
 * Known problems:
 *      - With the Neponset plugged into an Assabet, LCD powerdown
 *        doesn't work (LCD stays powered up).  Therefore we shouldn't
 *        blank the screen.
 *      - We don't limit the CPU clock rate nor the mode selection
 *        according to the available SDRAM bandwidth.
 *
 * Other notes:
 *      - Linear grayscale palettes and the kernel.
 *        Such code does not belong in the kernel.  The kernel frame buffer
 *        drivers do not expect a linear colourmap, but a colourmap based on
 *        the VT100 standard mapping.
 *
 *        If your _userspace_ requires a linear colourmap, then the setup of
 *        such a colourmap belongs _in userspace_, not in the kernel.  Code
 *        to set the colourmap correctly from user space has been sent to
 *        David Neuer.  It's around 8 lines of C code, plus another 4 to
 *        detect if we are using grayscale.
 *
 *      - The following must never be specified in a panel definition:
 *           LCCR0_LtlEnd, LCCR3_PixClkDiv, LCCR3_VrtSnchL, LCCR3_HorSnchL
 *
 *      - The following should be specified:
 *           either LCCR0_Color or LCCR0_Mono
 *           either LCCR0_Sngl or LCCR0_Dual
 *           either LCCR0_Act or LCCR0_Pas
 *           either LCCR3_OutEnH or LCCD3_OutEnL
 *           either LCCR3_PixRsEdg or LCCR3_PixFlEdg
 *           either LCCR3_ACBsDiv or LCCR3_ACBsCntOff
 *
 * Code Status:
 * 1999/04/01:
 *      - Driver appears to be working for Brutus 320x200x8bpp mode.  Other
 *        resolutions are working, but only the 8bpp mode is supported.
 *        Changes need to be made to the palette encode and decode routines
 *        to support 4 and 16 bpp modes.  
 *        Driver is not designed to be a module.  The FrameBuffer is statically
 *        allocated since dynamic allocation of a 300k buffer cannot be 
 *        guaranteed. 
 *
 * 1999/06/17:
 *      - FrameBuffer memory is now allocated at run-time when the
 *        driver is initialized.    
 *
 * 2000/04/10: Nicolas Pitre <nico@cam.org>
 *      - Big cleanup for dynamic selection of machine type at run time.
 *
 * 2000/07/19: Jamey Hicks <jamey@crl.dec.com>
 *      - Support for Bitsy aka Compaq iPAQ H3600 added.
 *
 * 2000/08/07: Tak-Shing Chan <tchan.rd@idthk.com>
 *             Jeff Sutherland <jsutherland@accelent.com>
 *      - Resolved an issue caused by a change made to the Assabet's PLD 
 *        earlier this year which broke the framebuffer driver for newer 
 *        Phase 4 Assabets.  Some other parameters were changed to optimize
 *        for the Sharp display.
 *
 * 2000/08/09: Kunihiko IMAI <imai@vasara.co.jp>
 *      - XP860 support added
 *
 * 2000/08/19: Mark Huang <mhuang@livetoy.com>
 *      - Allows standard options to be passed on the kernel command line
 *        for most common passive displays.
 *
 * 2000/08/29:
 *      - s/save_flags_cli/local_irq_save/
 *      - remove unneeded extra save_flags_cli in sa1100fb_enable_lcd_controller
 *
 * 2000/10/10: Erik Mouw <J.A.K.Mouw@its.tudelft.nl>
 *      - Updated LART stuff. Fixed some minor bugs.
 *
 * 2000/10/30: Murphy Chen <murphy@mail.dialogue.com.tw>
 *      - Pangolin support added
 *
 * 2000/10/31: Roman Jordan <jor@hoeft-wessel.de>
 *      - Huw Webpanel support added
 *
 * 2000/11/23: Eric Peng <ericpeng@coventive.com>
 *      - Freebird add
 *
 * 2001/02/07: Jamey Hicks <jamey.hicks@compaq.com> 
 *             Cliff Brake <cbrake@accelent.com>
 *      - Added PM callback
 *
 * 2001/05/26: <rmk@arm.linux.org.uk>
 *      - Fix 16bpp so that (a) we use the right colours rather than some
 *        totally random colour depending on what was in page 0, and (b)
 *        we don't de-reference a NULL pointer.
 *      - remove duplicated implementation of consistent_alloc()
 *      - convert dma address types to dma_addr_t
 *      - remove unused 'montype' stuff
 *      - remove redundant zero inits of init_var after the initial
 *        memzero.
 *      - remove allow_modeset (acornfb idea does not belong here)
 *
 * 2001/05/28: <rmk@arm.linux.org.uk>
 *      - massive cleanup - move machine dependent data into structures
 *      - I've left various #warnings in - if you see one, and know
 *        the hardware concerned, please get in contact with me.
 *
 * 2001/05/31: <rmk@arm.linux.org.uk>
 *      - Fix LCCR1 HSW value, fix all machine type specifications to
 *        keep values in line.  (Please check your machine type specs)
 *
 * 2001/06/10: <rmk@arm.linux.org.uk>
 *      - Fiddle with the LCD controller from task context only; mainly
 *        so that we can run with interrupts on, and sleep.
 *      - Convert #warnings into #errors.  No pain, no gain. ;)
 *
 * 2001/06/14: <rmk@arm.linux.org.uk>
 *      - Make the palette BPS value for 12bpp come out correctly.
 *      - Take notice of "greyscale" on any colour depth.
 *      - Make truecolor visuals use the RGB channel encoding information.
 *
 * 2001/07/02: <rmk@arm.linux.org.uk>
 *      - Fix colourmap problems.
 *
 * 2001/07/13: <abraham@2d3d.co.za>
 *      - Added support for the ICP LCD-Kit01 on LART. This LCD is
 *        manufactured by Prime View, model no V16C6448AB
 *
 * 2001/07/23: <rmk@arm.linux.org.uk>
 *      - Hand merge version from handhelds.org CVS tree.  See patch
 *        notes for 595/1 for more information.
 *      - Drop 12bpp (it's 16bpp with different colour register mappings).
 *      - This hardware can not do direct colour.  Therefore we don't
 *        support it.
 *
 * 2001/07/27: <rmk@arm.linux.org.uk>
 *      - Halve YRES on dual scan LCDs.
 *
 * 2001/08/22: <rmk@arm.linux.org.uk>
 *      - Add b/w iPAQ pixclock value.
 *
 * 2001/10/12: <rmk@arm.linux.org.uk>
 *      - Add patch 681/1 and clean up stork definitions.
 */

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/errno.h>
#include <linux/string.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
#include <linux/fb.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/cpufreq.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>

#include <asm/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include <asm/arch/assabet.h>
#include <asm/arch/shannon.h>

/*
 * debugging?
 */
#define DEBUG 0
/*
 * Complain if VAR is out of range.
 */
#define DEBUG_VAR 1

#undef ASSABET_PAL_VIDEO

#include "sa1100fb.h"

extern void (*sa1100fb_backlight_power)(int on);
extern void (*sa1100fb_lcd_power)(int on);

/*
 * IMHO this looks wrong.  In 8BPP, length should be 8.
 */
static struct sa1100fb_rgb rgb_8 = {
        .red    = { .offset = 0,  .length = 4, },
        .green  = { .offset = 0,  .length = 4, },
        .blue   = { .offset = 0,  .length = 4, },
        .transp = { .offset = 0,  .length = 0, },
};

static struct sa1100fb_rgb def_rgb_16 = {
        .red    = { .offset = 11, .length = 5, },
        .green  = { .offset = 5,  .length = 6, },
        .blue   = { .offset = 0,  .length = 5, },
        .transp = { .offset = 0,  .length = 0, },
};

#ifdef CONFIG_SA1100_ASSABET
#ifndef ASSABET_PAL_VIDEO
/*
 * The assabet uses a sharp LQ039Q2DS54 LCD module.  It is actually
 * takes an RGB666 signal, but we provide it with an RGB565 signal
 * instead (def_rgb_16).
 */
static struct sa1100fb_mach_info lq039q2ds54_info __initdata = {
        .pixclock       = 171521,       .bpp            = 16,
        .xres           = 320,          .yres           = 240,

        .hsync_len      = 5,            .vsync_len      = 1,
        .left_margin    = 61,           .upper_margin   = 3,
        .right_margin   = 9,            .lower_margin   = 0,

        .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,

        .lccr0          = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
        .lccr3          = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
};
#else
static struct sa1100fb_mach_info pal_info __initdata = {
        .pixclock       = 67797,        .bpp            = 16,
        .xres           = 640,          .yres           = 512,

        .hsync_len      = 64,           .vsync_len      = 6,
        .left_margin    = 125,          .upper_margin   = 70,
        .right_margin   = 115,          .lower_margin   = 36,

        .lccr0          = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
        .lccr3          = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
};
#endif
#endif

#ifdef CONFIG_SA1100_H3800
static struct sa1100fb_mach_info h3800_info __initdata = {
        .pixclock       = 174757,       .bpp            = 16,
        .xres           = 320,          .yres           = 240,

        .hsync_len      = 3,            .vsync_len      = 3,
        .left_margin    = 12,           .upper_margin   = 10,
        .right_margin   = 17,           .lower_margin   = 1,

        .cmap_static    = 1,

        .lccr0          = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
        .lccr3          = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
};
#endif

#ifdef CONFIG_SA1100_H3600
static struct sa1100fb_mach_info h3600_info __initdata = {
        .pixclock       = 174757,       .bpp            = 16,
        .xres           = 320,          .yres           = 240,

        .hsync_len      = 3,            .vsync_len      = 3,
        .left_margin    = 12,           .upper_margin   = 10,
        .right_margin   = 17,           .lower_margin   = 1,

        .cmap_static    = 1,

        .lccr0          = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
        .lccr3          = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
};

static struct sa1100fb_rgb h3600_rgb_16 = {
        .red    = { .offset = 12, .length = 4, },
        .green  = { .offset = 7,  .length = 4, },
        .blue   = { .offset = 1,  .length = 4, },
        .transp = { .offset = 0,  .length = 0, },
};
#endif

#ifdef CONFIG_SA1100_H3100
static struct sa1100fb_mach_info h3100_info __initdata = {
        .pixclock       = 406977,       .bpp            = 4,
        .xres           = 320,          .yres           = 240,

        .hsync_len      = 26,           .vsync_len      = 41,
        .left_margin    = 4,            .upper_margin   = 0,
        .right_margin   = 4,            .lower_margin   = 0,

        .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
        .cmap_greyscale = 1,
        .cmap_inverse   = 1,

        .lccr0          = LCCR0_Mono | LCCR0_4PixMono | LCCR0_Sngl | LCCR0_Pas,
        .lccr3          = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
};
#endif

#ifdef CONFIG_SA1100_COLLIE
static struct sa1100fb_mach_info collie_info __initdata = {
        .pixclock       = 171521,       .bpp            = 16,
        .xres           = 320,          .yres           = 240,

        .hsync_len      = 5,            .vsync_len      = 1,
        .left_margin    = 11,           .upper_margin   = 2,
        .right_margin   = 30,           .lower_margin   = 0,

        .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,

        .lccr0          = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
        .lccr3          = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
};
#endif

#ifdef LART_GREY_LCD
static struct sa1100fb_mach_info lart_grey_info __initdata = {
        .pixclock       = 150000,       .bpp            = 4,
        .xres           = 320,          .yres           = 240,

        .hsync_len      = 1,            .vsync_len      = 1,
        .left_margin    = 4,            .upper_margin   = 0,
        .right_margin   = 2,            .lower_margin   = 0,

        .cmap_greyscale = 1,
        .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,

        .lccr0          = LCCR0_Mono | LCCR0_Sngl | LCCR0_Pas | LCCR0_4PixMono,
        .lccr3          = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
};
#endif
#ifdef LART_COLOR_LCD
static struct sa1100fb_mach_info lart_color_info __initdata = {
        .pixclock       = 150000,       .bpp            = 16,
        .xres           = 320,          .yres           = 240,

        .hsync_len      = 2,            .vsync_len      = 3,
        .left_margin    = 69,           .upper_margin   = 14,
        .right_margin   = 8,            .lower_margin   = 4,

        .lccr0          = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
        .lccr3          = LCCR3_OutEnH | LCCR3_PixFlEdg | LCCR3_ACBsDiv(512),
};
#endif
#ifdef LART_VIDEO_OUT
static struct sa1100fb_mach_info lart_video_info __initdata = {
        .pixclock       = 39721,        .bpp            = 16,
        .xres           = 640,          .yres           = 480,

        .hsync_len      = 95,           .vsync_len      = 2,
        .left_margin    = 40,           .upper_margin   = 32,
        .right_margin   = 24,           .lower_margin   = 11,

        .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,

        .lccr0          = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
        .lccr3          = LCCR3_OutEnL | LCCR3_PixFlEdg | LCCR3_ACBsDiv(512),
};
#endif

#ifdef LART_KIT01_LCD
static struct sa1100fb_mach_info lart_kit01_info __initdata = {
        .pixclock       = 63291,        .bpp            = 16,
        .xres           = 640,          .yres           = 480,

        .hsync_len      = 64,           .vsync_len      = 3,
        .left_margin    = 122,          .upper_margin   = 45,
        .right_margin   = 10,           .lower_margin   = 10,

        .lccr0          = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
        .lccr3          = LCCR3_OutEnH | LCCR3_PixFlEdg
};
#endif

#ifdef CONFIG_SA1100_SHANNON
static struct sa1100fb_mach_info shannon_info __initdata = {
        .pixclock       = 152500,       .bpp            = 8,
        .xres           = 640,          .yres           = 480,

        .hsync_len      = 4,            .vsync_len      = 3,
        .left_margin    = 2,            .upper_margin   = 0,
        .right_margin   = 1,            .lower_margin   = 0,

        .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,

        .lccr0          = LCCR0_Color | LCCR0_Dual | LCCR0_Pas,
        .lccr3          = LCCR3_ACBsDiv(512),
};
#endif



static struct sa1100fb_mach_info * __init
sa1100fb_get_machine_info(struct sa1100fb_info *fbi)
{
        struct sa1100fb_mach_info *inf = NULL;

        /*
         *            R        G       B       T
         * default  {11,5}, { 5,6}, { 0,5}, { 0,0}
         * h3600    {12,4}, { 7,4}, { 1,4}, { 0,0}
         * freebird { 8,4}, { 4,4}, { 0,4}, {12,4}
         */
#ifdef CONFIG_SA1100_ASSABET
        if (machine_is_assabet()) {
#ifndef ASSABET_PAL_VIDEO
                inf = &lq039q2ds54_info;
#else
                inf = &pal_info;
#endif
        }
#endif
#ifdef CONFIG_SA1100_H3100
        if (machine_is_h3100()) {
                inf = &h3100_info;
        }
#endif
#ifdef CONFIG_SA1100_H3600
        if (machine_is_h3600()) {
                inf = &h3600_info;
                fbi->rgb[RGB_16] = &h3600_rgb_16;
        }
#endif
#ifdef CONFIG_SA1100_H3800
        if (machine_is_h3800()) {
                inf = &h3800_info;
        }
#endif
#ifdef CONFIG_SA1100_COLLIE
        if (machine_is_collie()) {
                inf = &collie_info;
        }
#endif
#ifdef CONFIG_SA1100_LART
        if (machine_is_lart()) {
#ifdef LART_GREY_LCD
                inf = &lart_grey_info;
#endif
#ifdef LART_COLOR_LCD
                inf = &lart_color_info;
#endif
#ifdef LART_VIDEO_OUT
                inf = &lart_video_info;
#endif
#ifdef LART_KIT01_LCD
                inf = &lart_kit01_info;
#endif
        }
#endif
#ifdef CONFIG_SA1100_SHANNON
        if (machine_is_shannon()) {
                inf = &shannon_info;
        }
#endif
        return inf;
}

static int sa1100fb_activate_var(struct fb_var_screeninfo *var, struct sa1100fb_info *);
static void set_ctrlr_state(struct sa1100fb_info *fbi, u_int state);

static inline void sa1100fb_schedule_work(struct sa1100fb_info *fbi, u_int state)
{
        unsigned long flags;

        local_irq_save(flags);
        /*
         * We need to handle two requests being made at the same time.
         * There are two important cases:
         *  1. When we are changing VT (C_REENABLE) while unblanking (C_ENABLE)
         *     We must perform the unblanking, which will do our REENABLE for us.
         *  2. When we are blanking, but immediately unblank before we have
         *     blanked.  We do the "REENABLE" thing here as well, just to be sure.
         */
        if (fbi->task_state == C_ENABLE && state == C_REENABLE)
                state = (u_int) -1;
        if (fbi->task_state == C_DISABLE && state == C_ENABLE)
                state = C_REENABLE;

        if (state != (u_int)-1) {
                fbi->task_state = state;
                schedule_work(&fbi->task);
        }
        local_irq_restore(flags);
}

static inline u_int chan_to_field(u_int chan, struct fb_bitfield *bf)
{
        chan &= 0xffff;
        chan >>= 16 - bf->length;
        return chan << bf->offset;
}

/*
 * Convert bits-per-pixel to a hardware palette PBS value.
 */
static inline u_int palette_pbs(struct fb_var_screeninfo *var)
{
        int ret = 0;
        switch (var->bits_per_pixel) {
        case 4:  ret = 0 << 12; break;
        case 8:  ret = 1 << 12; break;
        case 16: ret = 2 << 12; break;
        }
        return ret;
}

static int
sa1100fb_setpalettereg(u_int regno, u_int red, u_int green, u_int blue,
                       u_int trans, struct fb_info *info)
{
        struct sa1100fb_info *fbi = (struct sa1100fb_info *)info;
        u_int val, ret = 1;

        if (regno < fbi->palette_size) {
                val = ((red >> 4) & 0xf00);
                val |= ((green >> 8) & 0x0f0);
                val |= ((blue >> 12) & 0x00f);

                if (regno == 0)
                        val |= palette_pbs(&fbi->fb.var);

                fbi->palette_cpu[regno] = val;
                ret = 0;
        }
        return ret;
}

static int
sa1100fb_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
                   u_int trans, struct fb_info *info)
{
        struct sa1100fb_info *fbi = (struct sa1100fb_info *)info;
        unsigned int val;
        int ret = 1;

        /*
         * If inverse mode was selected, invert all the colours
         * rather than the register number.  The register number
         * is what you poke into the framebuffer to produce the
         * colour you requested.
         */
        if (fbi->cmap_inverse) {
                red   = 0xffff - red;
                green = 0xffff - green;
                blue  = 0xffff - blue;
        }

        /*
         * If greyscale is true, then we convert the RGB value
         * to greyscale no mater what visual we are using.
         */
        if (fbi->fb.var.grayscale)
                red = green = blue = (19595 * red + 38470 * green +
                                        7471 * blue) >> 16;

        switch (fbi->fb.fix.visual) {
        case FB_VISUAL_TRUECOLOR:
                /*
                 * 12 or 16-bit True Colour.  We encode the RGB value
                 * according to the RGB bitfield information.
                 */
                if (regno < 16) {
                        u32 *pal = fbi->fb.pseudo_palette;

                        val  = chan_to_field(red, &fbi->fb.var.red);
                        val |= chan_to_field(green, &fbi->fb.var.green);
                        val |= chan_to_field(blue, &fbi->fb.var.blue);

                        pal[regno] = val;
                        ret = 0;
                }
                break;

        case FB_VISUAL_STATIC_PSEUDOCOLOR:
        case FB_VISUAL_PSEUDOCOLOR:
                ret = sa1100fb_setpalettereg(regno, red, green, blue, trans, info);
                break;
        }

        return ret;
}

#ifdef CONFIG_CPU_FREQ
/*
 *  sa1100fb_display_dma_period()
 *    Calculate the minimum period (in picoseconds) between two DMA
 *    requests for the LCD controller.  If we hit this, it means we're
 *    doing nothing but LCD DMA.
 */
static inline unsigned int sa1100fb_display_dma_period(struct fb_var_screeninfo *var)
{
        /*
         * Period = pixclock * bits_per_byte * bytes_per_transfer
         *              / memory_bits_per_pixel;
         */
        return var->pixclock * 8 * 16 / var->bits_per_pixel;
}
#endif

/*
 *  sa1100fb_check_var():
 *    Round up in the following order: bits_per_pixel, xres,
 *    yres, xres_virtual, yres_virtual, xoffset, yoffset, grayscale,
 *    bitfields, horizontal timing, vertical timing.
 */
static int
sa1100fb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
{
        struct sa1100fb_info *fbi = (struct sa1100fb_info *)info;
        int rgbidx;

        if (var->xres < MIN_XRES)
                var->xres = MIN_XRES;
        if (var->yres < MIN_YRES)
                var->yres = MIN_YRES;
        if (var->xres > fbi->max_xres)
                var->xres = fbi->max_xres;
        if (var->yres > fbi->max_yres)
                var->yres = fbi->max_yres;
        var->xres_virtual = max(var->xres_virtual, var->xres);
        var->yres_virtual = max(var->yres_virtual, var->yres);

        DPRINTK("var->bits_per_pixel=%d\n", var->bits_per_pixel);
        switch (var->bits_per_pixel) {
        case 4:
                rgbidx = RGB_8;
                break;
        case 8:
                rgbidx = RGB_8;
                break;
        case 16:
                rgbidx = RGB_16;
                break;
        default:
                return -EINVAL;
        }

        /*
         * Copy the RGB parameters for this display
         * from the machine specific parameters.
         */
        var->red    = fbi->rgb[rgbidx]->red;
        var->green  = fbi->rgb[rgbidx]->green;
        var->blue   = fbi->rgb[rgbidx]->blue;
        var->transp = fbi->rgb[rgbidx]->transp;

        DPRINTK("RGBT length = %d:%d:%d:%d\n",
                var->red.length, var->green.length, var->blue.length,
                var->transp.length);

        DPRINTK("RGBT offset = %d:%d:%d:%d\n",
                var->red.offset, var->green.offset, var->blue.offset,
                var->transp.offset);

#ifdef CONFIG_CPU_FREQ
        printk(KERN_DEBUG "dma period = %d ps, clock = %d kHz\n",
                sa1100fb_display_dma_period(var),
                cpufreq_get(smp_processor_id()));
#endif

        return 0;
}

static inline void sa1100fb_set_truecolor(u_int is_true_color)
{
        if (machine_is_assabet()) {
#if 1           // phase 4 or newer Assabet's
                if (is_true_color)
                        ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
                else
                        ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
#else
                // older Assabet's
                if (is_true_color)
                        ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
                else
                        ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
#endif
        }
}

/*
 * sa1100fb_set_par():
 *      Set the user defined part of the display for the specified console
 */
static int sa1100fb_set_par(struct fb_info *info)
{
        struct sa1100fb_info *fbi = (struct sa1100fb_info *)info;
        struct fb_var_screeninfo *var = &info->var;
        unsigned long palette_mem_size;

        DPRINTK("set_par\n");

        if (var->bits_per_pixel == 16)
                fbi->fb.fix.visual = FB_VISUAL_TRUECOLOR;
        else if (!fbi->cmap_static)
                fbi->fb.fix.visual = FB_VISUAL_PSEUDOCOLOR;
        else {
                /*
                 * Some people have weird ideas about wanting static
                 * pseudocolor maps.  I suspect their user space
                 * applications are broken.
                 */
                fbi->fb.fix.visual = FB_VISUAL_STATIC_PSEUDOCOLOR;
        }

        fbi->fb.fix.line_length = var->xres_virtual *
                                  var->bits_per_pixel / 8;
        fbi->palette_size = var->bits_per_pixel == 8 ? 256 : 16;

        palette_mem_size = fbi->palette_size * sizeof(u16);

        DPRINTK("palette_mem_size = 0x%08lx\n", (u_long) palette_mem_size);

        fbi->palette_cpu = (u16 *)(fbi->map_cpu + PAGE_SIZE - palette_mem_size);
        fbi->palette_dma = fbi->map_dma + PAGE_SIZE - palette_mem_size;

        /*
         * Set (any) board control register to handle new color depth
         */
        sa1100fb_set_truecolor(fbi->fb.fix.visual == FB_VISUAL_TRUECOLOR);
        sa1100fb_activate_var(var, fbi);

        return 0;
}

#if 0
static int
sa1100fb_set_cmap(struct fb_cmap *cmap, int kspc, int con,
                  struct fb_info *info)
{
        struct sa1100fb_info *fbi = (struct sa1100fb_info *)info;

        /*
         * Make sure the user isn't doing something stupid.
         */
        if (!kspc && (fbi->fb.var.bits_per_pixel == 16 || fbi->cmap_static))
                return -EINVAL;

        return gen_set_cmap(cmap, kspc, con, info);
}
#endif

/*
 * Formal definition of the VESA spec:
 *  On
 *      This refers to the state of the display when it is in full operation
 *  Stand-By
 *      This defines an optional operating state of minimal power reduction with
 *      the shortest recovery time
 *  Suspend
 *      This refers to a level of power management in which substantial power
 *      reduction is achieved by the display.  The display can have a longer 
 *      recovery time from this state than from the Stand-by state
 *  Off
 *      This indicates that the display is consuming the lowest level of power
 *      and is non-operational. Recovery from this state may optionally require
 *      the user to manually power on the monitor
 *
 *  Now, the fbdev driver adds an additional state, (blank), where they
 *  turn off the video (maybe by colormap tricks), but don't mess with the
 *  video itself: think of it semantically between on and Stand-By.
 *
 *  So here's what we should do in our fbdev blank routine:
 *
 *      VESA_NO_BLANKING (mode 0)       Video on,  front/back light on
 *      VESA_VSYNC_SUSPEND (mode 1)     Video on,  front/back light off
 *      VESA_HSYNC_SUSPEND (mode 2)     Video on,  front/back light off
 *      VESA_POWERDOWN (mode 3)         Video off, front/back light off
 *
 *  This will match the matrox implementation.
 */
/*
 * sa1100fb_blank():
 *      Blank the display by setting all palette values to zero.  Note, the 
 *      12 and 16 bpp modes don't really use the palette, so this will not
 *      blank the display in all modes.  
 */
static int sa1100fb_blank(int blank, struct fb_info *info)
{
        struct sa1100fb_info *fbi = (struct sa1100fb_info *)info;
        int i;

        DPRINTK("sa1100fb_blank: blank=%d\n", blank);

        switch (blank) {
        case FB_BLANK_POWERDOWN:
        case FB_BLANK_VSYNC_SUSPEND:
        case FB_BLANK_HSYNC_SUSPEND:
        case FB_BLANK_NORMAL:
                if (fbi->fb.fix.visual == FB_VISUAL_PSEUDOCOLOR ||
                    fbi->fb.fix.visual == FB_VISUAL_STATIC_PSEUDOCOLOR)
                        for (i = 0; i < fbi->palette_size; i++)
                                sa1100fb_setpalettereg(i, 0, 0, 0, 0, info);
                sa1100fb_schedule_work(fbi, C_DISABLE);
                break;

        case FB_BLANK_UNBLANK:
                if (fbi->fb.fix.visual == FB_VISUAL_PSEUDOCOLOR ||
                    fbi->fb.fix.visual == FB_VISUAL_STATIC_PSEUDOCOLOR)
                        fb_set_cmap(&fbi->fb.cmap, info);
                sa1100fb_schedule_work(fbi, C_ENABLE);
        }
        return 0;
}

static int sa1100fb_mmap(struct fb_info *info,
                         struct vm_area_struct *vma)
{
        struct sa1100fb_info *fbi = (struct sa1100fb_info *)info;
        unsigned long start, len, off = vma->vm_pgoff << PAGE_SHIFT;

        if (off < info->fix.smem_len) {
                vma->vm_pgoff += 1; /* skip over the palette */
                return dma_mmap_writecombine(fbi->dev, vma, fbi->map_cpu,
                                             fbi->map_dma, fbi->map_size);
        }

        start = info->fix.mmio_start;
        len = PAGE_ALIGN((start & ~PAGE_MASK) + info->fix.mmio_len);

        if ((vma->vm_end - vma->vm_start + off) > len)
                return -EINVAL;

        off += start & PAGE_MASK;
        vma->vm_pgoff = off >> PAGE_SHIFT;
        vma->vm_flags |= VM_IO;
        vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
        return io_remap_pfn_range(vma, vma->vm_start, off >> PAGE_SHIFT,
                                   vma->vm_end - vma->vm_start,
                                   vma->vm_page_prot);
}

static struct fb_ops sa1100fb_ops = {
        .owner          = THIS_MODULE,
        .fb_check_var   = sa1100fb_check_var,
        .fb_set_par     = sa1100fb_set_par,
//      .fb_set_cmap    = sa1100fb_set_cmap,
        .fb_setcolreg   = sa1100fb_setcolreg,
        .fb_fillrect    = cfb_fillrect,
        .fb_copyarea    = cfb_copyarea,
        .fb_imageblit   = cfb_imageblit,
        .fb_blank       = sa1100fb_blank,
        .fb_mmap        = sa1100fb_mmap,
};

/*
 * Calculate the PCD value from the clock rate (in picoseconds).
 * We take account of the PPCR clock setting.
 */
static inline unsigned int get_pcd(unsigned int pixclock, unsigned int cpuclock)
{
        unsigned int pcd = cpuclock / 100;

        pcd *= pixclock;
        pcd /= 10000000;

        return pcd + 1; /* make up for integer math truncations */
}

/*
 * sa1100fb_activate_var():
 *      Configures LCD Controller based on entries in var parameter.  Settings are      
 *      only written to the controller if changes were made.  
 */
static int sa1100fb_activate_var(struct fb_var_screeninfo *var, struct sa1100fb_info *fbi)
{
        struct sa1100fb_lcd_reg new_regs;
        u_int half_screen_size, yres, pcd;
        u_long flags;

        DPRINTK("Configuring SA1100 LCD\n");

        DPRINTK("var: xres=%d hslen=%d lm=%d rm=%d\n",
                var->xres, var->hsync_len,
                var->left_margin, var->right_margin);
        DPRINTK("var: yres=%d vslen=%d um=%d bm=%d\n",
                var->yres, var->vsync_len,
                var->upper_margin, var->lower_margin);

#if DEBUG_VAR
        if (var->xres < 16        || var->xres > 1024)
                printk(KERN_ERR "%s: invalid xres %d\n",
                        fbi->fb.fix.id, var->xres);
        if (var->hsync_len < 1    || var->hsync_len > 64)
                printk(KERN_ERR "%s: invalid hsync_len %d\n",
                        fbi->fb.fix.id, var->hsync_len);
        if (var->left_margin < 1  || var->left_margin > 255)
                printk(KERN_ERR "%s: invalid left_margin %d\n",
                        fbi->fb.fix.id, var->left_margin);
        if (var->right_margin < 1 || var->right_margin > 255)
                printk(KERN_ERR "%s: invalid right_margin %d\n",
                        fbi->fb.fix.id, var->right_margin);
        if (var->yres < 1         || var->yres > 1024)
                printk(KERN_ERR "%s: invalid yres %d\n",
                        fbi->fb.fix.id, var->yres);
        if (var->vsync_len < 1    || var->vsync_len > 64)
                printk(KERN_ERR "%s: invalid vsync_len %d\n",
                        fbi->fb.fix.id, var->vsync_len);
        if (var->upper_margin < 0 || var->upper_margin > 255)
                printk(KERN_ERR "%s: invalid upper_margin %d\n",
                        fbi->fb.fix.id, var->upper_margin);
        if (var->lower_margin < 0 || var->lower_margin > 255)
                printk(KERN_ERR "%s: invalid lower_margin %d\n",
                        fbi->fb.fix.id, var->lower_margin);
#endif

        new_regs.lccr0 = fbi->lccr0 |
                LCCR0_LEN | LCCR0_LDM | LCCR0_BAM |
                LCCR0_ERM | LCCR0_LtlEnd | LCCR0_DMADel(0);

        new_regs.lccr1 =
                LCCR1_DisWdth(var->xres) +
                LCCR1_HorSnchWdth(var->hsync_len) +
                LCCR1_BegLnDel(var->left_margin) +
                LCCR1_EndLnDel(var->right_margin);

        /*
         * If we have a dual scan LCD, then we need to halve
         * the YRES parameter.
         */
        yres = var->yres;
        if (fbi->lccr0 & LCCR0_Dual)
                yres /= 2;

        new_regs.lccr2 =
                LCCR2_DisHght(yres) +
                LCCR2_VrtSnchWdth(var->vsync_len) +
                LCCR2_BegFrmDel(var->upper_margin) +
                LCCR2_EndFrmDel(var->lower_margin);

        pcd = get_pcd(var->pixclock, cpufreq_get(0));
        new_regs.lccr3 = LCCR3_PixClkDiv(pcd) | fbi->lccr3 |
                (var->sync & FB_SYNC_HOR_HIGH_ACT ? LCCR3_HorSnchH : LCCR3_HorSnchL) |
                (var->sync & FB_SYNC_VERT_HIGH_ACT ? LCCR3_VrtSnchH : LCCR3_VrtSnchL);

        DPRINTK("nlccr0 = 0x%08lx\n", new_regs.lccr0);
        DPRINTK("nlccr1 = 0x%08lx\n", new_regs.lccr1);
        DPRINTK("nlccr2 = 0x%08lx\n", new_regs.lccr2);
        DPRINTK("nlccr3 = 0x%08lx\n", new_regs.lccr3);

        half_screen_size = var->bits_per_pixel;
        half_screen_size = half_screen_size * var->xres * var->yres / 16;

        /* Update shadow copy atomically */
        local_irq_save(flags);
        fbi->dbar1 = fbi->palette_dma;
        fbi->dbar2 = fbi->screen_dma + half_screen_size;

        fbi->reg_lccr0 = new_regs.lccr0;
        fbi->reg_lccr1 = new_regs.lccr1;
        fbi->reg_lccr2 = new_regs.lccr2;
        fbi->reg_lccr3 = new_regs.lccr3;
        local_irq_restore(flags);

        /*
         * Only update the registers if the controller is enabled
         * and something has changed.
         */
        if ((LCCR0 != fbi->reg_lccr0)       || (LCCR1 != fbi->reg_lccr1) ||
            (LCCR2 != fbi->reg_lccr2)       || (LCCR3 != fbi->reg_lccr3) ||
            (DBAR1 != fbi->dbar1) || (DBAR2 != fbi->dbar2))
                sa1100fb_schedule_work(fbi, C_REENABLE);

        return 0;
}

/*
 * NOTE!  The following functions are purely helpers for set_ctrlr_state.
 * Do not call them directly; set_ctrlr_state does the correct serialisation
 * to ensure that things happen in the right way 100% of time time.
 *      -- rmk
 */
static inline void __sa1100fb_backlight_power(struct sa1100fb_info *fbi, int on)
{
        DPRINTK("backlight o%s\n", on ? "n" : "ff");

        if (sa1100fb_backlight_power)
                sa1100fb_backlight_power(on);
}

static inline void __sa1100fb_lcd_power(struct sa1100fb_info *fbi, int on)
{
        DPRINTK("LCD power o%s\n", on ? "n" : "ff");

        if (sa1100fb_lcd_power)
                sa1100fb_lcd_power(on);
}

static void sa1100fb_setup_gpio(struct sa1100fb_info *fbi)
{
        u_int mask = 0;

        /*
         * Enable GPIO<9:2> for LCD use if:
         *  1. Active display, or
         *  2. Color Dual Passive display
         *
         * see table 11.8 on page 11-27 in the SA1100 manual
         *   -- Erik.
         *
         * SA1110 spec update nr. 25 says we can and should
         * clear LDD15 to 12 for 4 or 8bpp modes with active
         * panels.  
         */
        if ((fbi->reg_lccr0 & LCCR0_CMS) == LCCR0_Color &&
            (fbi->reg_lccr0 & (LCCR0_Dual|LCCR0_Act)) != 0) {
                mask = GPIO_LDD11 | GPIO_LDD10 | GPIO_LDD9  | GPIO_LDD8;

                if (fbi->fb.var.bits_per_pixel > 8 ||
                    (fbi->reg_lccr0 & (LCCR0_Dual|LCCR0_Act)) == LCCR0_Dual)
                        mask |= GPIO_LDD15 | GPIO_LDD14 | GPIO_LDD13 | GPIO_LDD12;

        }

        if (mask) {
                GPDR |= mask;
                GAFR |= mask;
        }
}

static void sa1100fb_enable_controller(struct sa1100fb_info *fbi)
{
        DPRINTK("Enabling LCD controller\n");

        /*
         * Make sure the mode bits are present in the first palette entry
         */
        fbi->palette_cpu[0] &= 0xcfff;
        fbi->palette_cpu[0] |= palette_pbs(&fbi->fb.var);

        /* Sequence from 11.7.10 */
        LCCR3 = fbi->reg_lccr3;
        LCCR2 = fbi->reg_lccr2;
        LCCR1 = fbi->reg_lccr1;
        LCCR0 = fbi->reg_lccr0 & ~LCCR0_LEN;
        DBAR1 = fbi->dbar1;
        DBAR2 = fbi->dbar2;
        LCCR0 |= LCCR0_LEN;

        if (machine_is_shannon()) {
                GPDR |= SHANNON_GPIO_DISP_EN;
                GPSR |= SHANNON_GPIO_DISP_EN;
        }

        DPRINTK("DBAR1 = 0x%08x\n", DBAR1);
        DPRINTK("DBAR2 = 0x%08x\n", DBAR2);
        DPRINTK("LCCR0 = 0x%08x\n", LCCR0);
        DPRINTK("LCCR1 = 0x%08x\n", LCCR1);
        DPRINTK("LCCR2 = 0x%08x\n", LCCR2);
        DPRINTK("LCCR3 = 0x%08x\n", LCCR3);
}

static void sa1100fb_disable_controller(struct sa1100fb_info *fbi)
{
        DECLARE_WAITQUEUE(wait, current);

        DPRINTK("Disabling LCD controller\n");

        if (machine_is_shannon()) {
                GPCR |= SHANNON_GPIO_DISP_EN;
        }       

        set_current_state(TASK_UNINTERRUPTIBLE);
        add_wait_queue(&fbi->ctrlr_wait, &wait);

        LCSR = 0xffffffff;      /* Clear LCD Status Register */
        LCCR0 &= ~LCCR0_LDM;    /* Enable LCD Disable Done Interrupt */
        LCCR0 &= ~LCCR0_LEN;    /* Disable LCD Controller */

        schedule_timeout(20 * HZ / 1000);
        remove_wait_queue(&fbi->ctrlr_wait, &wait);
}

/*
 *  sa1100fb_handle_irq: Handle 'LCD DONE' interrupts.
 */
static irqreturn_t sa1100fb_handle_irq(int irq, void *dev_id)
{
        struct sa1100fb_info *fbi = dev_id;
        unsigned int lcsr = LCSR;

        if (lcsr & LCSR_LDD) {
                LCCR0 |= LCCR0_LDM;
                wake_up(&fbi->ctrlr_wait);
        }

        LCSR = lcsr;
        return IRQ_HANDLED;
}

/*
 * This function must be called from task context only, since it will
 * sleep when disabling the LCD controller, or if we get two contending
 * processes trying to alter state.
 */
static void set_ctrlr_state(struct sa1100fb_info *fbi, u_int state)
{
        u_int old_state;

        down(&fbi->ctrlr_sem);

        old_state = fbi->state;

        /*
         * Hack around fbcon initialisation.
         */
        if (old_state == C_STARTUP && state == C_REENABLE)
                state = C_ENABLE;

        switch (state) {
        case C_DISABLE_CLKCHANGE:
                /*
                 * Disable controller for clock change.  If the
                 * controller is already disabled, then do nothing.
                 */
                if (old_state != C_DISABLE && old_state != C_DISABLE_PM) {
                        fbi->state = state;
                        sa1100fb_disable_controller(fbi);
                }
                break;

        case C_DISABLE_PM:
        case C_DISABLE:
                /*
                 * Disable controller
                 */
                if (old_state != C_DISABLE) {
                        fbi->state = state;

                        __sa1100fb_backlight_power(fbi, 0);
                        if (old_state != C_DISABLE_CLKCHANGE)
                                sa1100fb_disable_controller(fbi);
                        __sa1100fb_lcd_power(fbi, 0);
                }
                break;

        case C_ENABLE_CLKCHANGE:
                /*
                 * Enable the controller after clock change.  Only
                 * do this if we were disabled for the clock change.
                 */
                if (old_state == C_DISABLE_CLKCHANGE) {
                        fbi->state = C_ENABLE;
                        sa1100fb_enable_controller(fbi);
                }
                break;

        case C_REENABLE:
                /*
                 * Re-enable the controller only if it was already
                 * enabled.  This is so we reprogram the control
                 * registers.
                 */
                if (old_state == C_ENABLE) {
                        sa1100fb_disable_controller(fbi);
                        sa1100fb_setup_gpio(fbi);
                        sa1100fb_enable_controller(fbi);
                }
                break;

        case C_ENABLE_PM:
                /*
                 * Re-enable the controller after PM.  This is not
                 * perfect - think about the case where we were doing
                 * a clock change, and we suspended half-way through.
                 */
                if (old_state != C_DISABLE_PM)
                        break;
                /* fall through */

        case C_ENABLE:
                /*
                 * Power up the LCD screen, enable controller, and
                 * turn on the backlight.
                 */
                if (old_state != C_ENABLE) {
                        fbi->state = C_ENABLE;
                        sa1100fb_setup_gpio(fbi);
                        __sa1100fb_lcd_power(fbi, 1);
                        sa1100fb_enable_controller(fbi);
                        __sa1100fb_backlight_power(fbi, 1);
                }
                break;
        }
        up(&fbi->ctrlr_sem);
}

/*
 * Our LCD controller task (which is called when we blank or unblank)
 * via keventd.
 */
static void sa1100fb_task(struct work_struct *w)
{
        struct sa1100fb_info *fbi = container_of(w, struct sa1100fb_info, task);
        u_int state = xchg(&fbi->task_state, -1);

        set_ctrlr_state(fbi, state);
}

#ifdef CONFIG_CPU_FREQ
/*
 * Calculate the minimum DMA period over all displays that we own.
 * This, together with the SDRAM bandwidth defines the slowest CPU
 * frequency that can be selected.
 */
static unsigned int sa1100fb_min_dma_period(struct sa1100fb_info *fbi)
{
#if 0
        unsigned int min_period = (unsigned int)-1;
        int i;

        for (i = 0; i < MAX_NR_CONSOLES; i++) {
                struct display *disp = &fb_display[i];
                unsigned int period;

                /*
                 * Do we own this display?
                 */
                if (disp->fb_info != &fbi->fb)
                        continue;

                /*
                 * Ok, calculate its DMA period
                 */
                period = sa1100fb_display_dma_period(&disp->var);
                if (period < min_period)
                        min_period = period;
        }

        return min_period;
#else
        /*
         * FIXME: we need to verify _all_ consoles.
         */
        return sa1100fb_display_dma_period(&fbi->fb.var);
#endif
}

/*
 * CPU clock speed change handler.  We need to adjust the LCD timing
 * parameters when the CPU clock is adjusted by the power management
 * subsystem.
 */
static int
sa1100fb_freq_transition(struct notifier_block *nb, unsigned long val,
                         void *data)
{
        struct sa1100fb_info *fbi = TO_INF(nb, freq_transition);
        struct cpufreq_freqs *f = data;
        u_int pcd;

        switch (val) {
        case CPUFREQ_PRECHANGE:
                set_ctrlr_state(fbi, C_DISABLE_CLKCHANGE);
                break;

        case CPUFREQ_POSTCHANGE:
                pcd = get_pcd(fbi->fb.var.pixclock, f->new);
                fbi->reg_lccr3 = (fbi->reg_lccr3 & ~0xff) | LCCR3_PixClkDiv(pcd);
                set_ctrlr_state(fbi, C_ENABLE_CLKCHANGE);
                break;
        }
        return 0;
}

static int
sa1100fb_freq_policy(struct notifier_block *nb, unsigned long val,
                     void *data)
{
        struct sa1100fb_info *fbi = TO_INF(nb, freq_policy);
        struct cpufreq_policy *policy = data;

        switch (val) {
        case CPUFREQ_ADJUST:
        case CPUFREQ_INCOMPATIBLE:
                printk(KERN_DEBUG "min dma period: %d ps, "
                        "new clock %d kHz\n", sa1100fb_min_dma_period(fbi),
                        policy->max);
                /* todo: fill in min/max values */
                break;
        case CPUFREQ_NOTIFY:
                do {} while(0);
                /* todo: panic if min/max values aren't fulfilled 
                 * [can't really happen unless there's a bug in the
                 * CPU policy verififcation process *
                 */
                break;
        }
        return 0;
}
#endif

#ifdef CONFIG_PM
/*
 * Power management hooks.  Note that we won't be called from IRQ context,
 * unlike the blank functions above, so we may sleep.
 */
static int sa1100fb_suspend(struct platform_device *dev, pm_message_t state)
{
        struct sa1100fb_info *fbi = platform_get_drvdata(dev);

        set_ctrlr_state(fbi, C_DISABLE_PM);
        return 0;
}

static int sa1100fb_resume(struct platform_device *dev)
{
        struct sa1100fb_info *fbi = platform_get_drvdata(dev);

        set_ctrlr_state(fbi, C_ENABLE_PM);
        return 0;
}
#else
#define sa1100fb_suspend        NULL
#define sa1100fb_resume         NULL
#endif

/*
 * sa1100fb_map_video_memory():
 *      Allocates the DRAM memory for the frame buffer.  This buffer is  
 *      remapped into a non-cached, non-buffered, memory region to  
 *      allow palette and pixel writes to occur without flushing the 
 *      cache.  Once this area is remapped, all virtual memory
 *      access to the video memory should occur at the new region.
 */
static int __init sa1100fb_map_video_memory(struct sa1100fb_info *fbi)
{
        /*
         * We reserve one page for the palette, plus the size
         * of the framebuffer.
         */
        fbi->map_size = PAGE_ALIGN(fbi->fb.fix.smem_len + PAGE_SIZE);
        fbi->map_cpu = dma_alloc_writecombine(fbi->dev, fbi->map_size,
                                              &fbi->map_dma, GFP_KERNEL);

        if (fbi->map_cpu) {
                fbi->fb.screen_base = fbi->map_cpu + PAGE_SIZE;
                fbi->screen_dma = fbi->map_dma + PAGE_SIZE;
                /*
                 * FIXME: this is actually the wrong thing to place in
                 * smem_start.  But fbdev suffers from the problem that
                 * it needs an API which doesn't exist (in this case,
                 * dma_writecombine_mmap)
                 */
                fbi->fb.fix.smem_start = fbi->screen_dma;
        }

        return fbi->map_cpu ? 0 : -ENOMEM;
}

/* Fake monspecs to fill in fbinfo structure */
static struct fb_monspecs monspecs __initdata = {
        .hfmin  = 30000,
        .hfmax  = 70000,
        .vfmin  = 50,
        .vfmax  = 65,
};


static struct sa1100fb_info * __init sa1100fb_init_fbinfo(struct device *dev)
{
        struct sa1100fb_mach_info *inf;
        struct sa1100fb_info *fbi;

        fbi = kmalloc(sizeof(struct sa1100fb_info) + sizeof(u32) * 16,
                      GFP_KERNEL);
        if (!fbi)
                return NULL;

        memset(fbi, 0, sizeof(struct sa1100fb_info));
        fbi->dev = dev;

        strcpy(fbi->fb.fix.id, SA1100_NAME);

        fbi->fb.fix.type        = FB_TYPE_PACKED_PIXELS;
        fbi->fb.fix.type_aux    = 0;
        fbi->fb.fix.xpanstep    = 0;
        fbi->fb.fix.ypanstep    = 0;
        fbi->fb.fix.ywrapstep   = 0;
        fbi->fb.fix.accel       = FB_ACCEL_NONE;

        fbi->fb.var.nonstd      = 0;
        fbi->fb.var.activate    = FB_ACTIVATE_NOW;
        fbi->fb.var.height      = -1;
        fbi->fb.var.width       = -1;
        fbi->fb.var.accel_flags = 0;
        fbi->fb.var.vmode       = FB_VMODE_NONINTERLACED;

        fbi->fb.fbops           = &sa1100fb_ops;
        fbi->fb.flags           = FBINFO_DEFAULT;
        fbi->fb.monspecs        = monspecs;
        fbi->fb.pseudo_palette  = (fbi + 1);

        fbi->rgb[RGB_8]         = &rgb_8;
        fbi->rgb[RGB_16]        = &def_rgb_16;

        inf = sa1100fb_get_machine_info(fbi);

        /*
         * People just don't seem to get this.  We don't support
         * anything but correct entries now, so panic if someone
         * does something stupid.
         */
        if (inf->lccr3 & (LCCR3_VrtSnchL|LCCR3_HorSnchL|0xff) ||
            inf->pixclock == 0)
                panic("sa1100fb error: invalid LCCR3 fields set or zero "
                        "pixclock.");

        fbi->max_xres                   = inf->xres;
        fbi->fb.var.xres                = inf->xres;
        fbi->fb.var.xres_virtual        = inf->xres;
        fbi->max_yres                   = inf->yres;
        fbi->fb.var.yres                = inf->yres;
        fbi->fb.var.yres_virtual        = inf->yres;
        fbi->max_bpp                    = inf->bpp;
        fbi->fb.var.bits_per_pixel      = inf->bpp;
        fbi->fb.var.pixclock            = inf->pixclock;
        fbi->fb.var.hsync_len           = inf->hsync_len;
        fbi->fb.var.left_margin         = inf->left_margin;
        fbi->fb.var.right_margin        = inf->right_margin;
        fbi->fb.var.vsync_len           = inf->vsync_len;
        fbi->fb.var.upper_margin        = inf->upper_margin;
        fbi->fb.var.lower_margin        = inf->lower_margin;
        fbi->fb.var.sync                = inf->sync;
        fbi->fb.var.grayscale           = inf->cmap_greyscale;
        fbi->cmap_inverse               = inf->cmap_inverse;
        fbi->cmap_static                = inf->cmap_static;
        fbi->lccr0                      = inf->lccr0;
        fbi->lccr3                      = inf->lccr3;
        fbi->state                      = C_STARTUP;
        fbi->task_state                 = (u_char)-1;
        fbi->fb.fix.smem_len            = fbi->max_xres * fbi->max_yres *
                                          fbi->max_bpp / 8;

        init_waitqueue_head(&fbi->ctrlr_wait);
        INIT_WORK(&fbi->task, sa1100fb_task);
        init_MUTEX(&fbi->ctrlr_sem);

        return fbi;
}

static int __init sa1100fb_probe(struct platform_device *pdev)
{
        struct sa1100fb_info *fbi;
        int ret, irq;

        irq = platform_get_irq(pdev, 0);
        if (irq < 0)
                return -EINVAL;

        if (!request_mem_region(0xb0100000, 0x10000, "LCD"))
                return -EBUSY;

        fbi = sa1100fb_init_fbinfo(&pdev->dev);
        ret = -ENOMEM;
        if (!fbi)
                goto failed;

        /* Initialize video memory */
        ret = sa1100fb_map_video_memory(fbi);
        if (ret)
                goto failed;

        ret = request_irq(irq, sa1100fb_handle_irq, IRQF_DISABLED,
                          "LCD", fbi);
        if (ret) {
                printk(KERN_ERR "sa1100fb: request_irq failed: %d\n", ret);
                goto failed;
        }

#ifdef ASSABET_PAL_VIDEO
        if (machine_is_assabet())
                ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
#endif

        /*
         * This makes sure that our colour bitfield
         * descriptors are correctly initialised.
         */
        sa1100fb_check_var(&fbi->fb.var, &fbi->fb);

        platform_set_drvdata(pdev, fbi);

        ret = register_framebuffer(&fbi->fb);
        if (ret < 0)
                goto err_free_irq;

#ifdef CONFIG_CPU_FREQ
        fbi->freq_transition.notifier_call = sa1100fb_freq_transition;
        fbi->freq_policy.notifier_call = sa1100fb_freq_policy;
        cpufreq_register_notifier(&fbi->freq_transition, CPUFREQ_TRANSITION_NOTIFIER);
        cpufreq_register_notifier(&fbi->freq_policy, CPUFREQ_POLICY_NOTIFIER);
#endif

        /* This driver cannot be unloaded at the moment */
        return 0;

 err_free_irq:
        free_irq(irq, fbi);
 failed:
        platform_set_drvdata(pdev, NULL);
        kfree(fbi);
        release_mem_region(0xb0100000, 0x10000);
        return ret;
}

static struct platform_driver sa1100fb_driver = {
        .probe          = sa1100fb_probe,
        .suspend        = sa1100fb_suspend,
        .resume         = sa1100fb_resume,
        .driver         = {
                .name   = "sa11x0-fb",
        },
};

int __init sa1100fb_init(void)
{
        if (fb_get_options("sa1100fb", NULL))
                return -ENODEV;

        return platform_driver_register(&sa1100fb_driver);
}

int __init sa1100fb_setup(char *options)
{
#if 0
        char *this_opt;

        if (!options || !*options)
                return 0;

        while ((this_opt = strsep(&options, ",")) != NULL) {

                if (!strncmp(this_opt, "bpp:", 4))
                        current_par.max_bpp =
                            simple_strtoul(this_opt + 4, NULL, 0);

                if (!strncmp(this_opt, "lccr0:", 6))
                        lcd_shadow.lccr0 =
                            simple_strtoul(this_opt + 6, NULL, 0);
                if (!strncmp(this_opt, "lccr1:", 6)) {
                        lcd_shadow.lccr1 =
                            simple_strtoul(this_opt + 6, NULL, 0);
                        current_par.max_xres =
                            (lcd_shadow.lccr1 & 0x3ff) + 16;
                }
                if (!strncmp(this_opt, "lccr2:", 6)) {
                        lcd_shadow.lccr2 =
                            simple_strtoul(this_opt + 6, NULL, 0);
                        current_par.max_yres =
                            (lcd_shadow.
                             lccr0 & LCCR0_SDS) ? ((lcd_shadow.
                                                    lccr2 & 0x3ff) +
                                                   1) *
                            2 : ((lcd_shadow.lccr2 & 0x3ff) + 1);
                }
                if (!strncmp(this_opt, "lccr3:", 6))
                        lcd_shadow.lccr3 =
                            simple_strtoul(this_opt + 6, NULL, 0);
        }
#endif
        return 0;
}

module_init(sa1100fb_init);
MODULE_DESCRIPTION("StrongARM-1100/1110 framebuffer driver");
MODULE_LICENSE("GPL");