drivers/pcmcia/sa1100_generic.c

   1 /*======================================================================
   2
   3     Device driver for the PCMCIA control functionality of StrongARM
   4     SA-1100 microprocessors.
   5
   6     The contents of this file are subject to the Mozilla Public
   7     License Version 1.1 (the "License"); you may not use this file
   8     except in compliance with the License. You may obtain a copy of
   9     the License at http://www.mozilla.org/MPL/
  10
  11     Software distributed under the License is distributed on an "AS
  12     IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
  13     implied. See the License for the specific language governing
  14     rights and limitations under the License.
  15
  16     The initial developer of the original code is John G. Dorsey
  17     <john+@cs.cmu.edu>.  Portions created by John G. Dorsey are
  18     Copyright (C) 1999 John G. Dorsey.  All Rights Reserved.
  19
  20     Alternatively, the contents of this file may be used under the
  21     terms of the GNU Public License version 2 (the "GPL"), in which
  22     case the provisions of the GPL are applicable instead of the
  23     above.  If you wish to allow the use of your version of this file
  24     only under the terms of the GPL and not to allow others to use
  25     your version of this file under the MPL, indicate your decision
  26     by deleting the provisions above and replace them with the notice
  27     and other provisions required by the GPL.  If you do not delete
  28     the provisions above, a recipient may use your version of this
  29     file under either the MPL or the GPL.
  30
  31 ======================================================================*/
  32
  33 #include <linux/module.h>
  34 #include <linux/init.h>
  35 #include <linux/config.h>
  36 #include <linux/platform_device.h>
  37
  38 #include <pcmcia/cs_types.h>
  39 #include <pcmcia/cs.h>
  40 #include <pcmcia/ss.h>
  41
  42 #include <asm/hardware/scoop.h>
  43
  44 #include "sa1100_generic.h"
  45
  46 int __init pcmcia_collie_init(struct device *dev);
  47
  48 static int (*sa11x0_pcmcia_hw_init[])(struct device *dev) = {
  49 #ifdef CONFIG_SA1100_ASSABET
  50         pcmcia_assabet_init,
  51 #endif
  52 #ifdef CONFIG_SA1100_CERF
  53         pcmcia_cerf_init,
  54 #endif
  55 #ifdef CONFIG_SA1100_H3600
  56         pcmcia_h3600_init,
  57 #endif
  58 #ifdef CONFIG_SA1100_SHANNON
  59         pcmcia_shannon_init,
  60 #endif
  61 #ifdef CONFIG_SA1100_SIMPAD
  62         pcmcia_simpad_init,
  63 #endif
  64 #ifdef CONFIG_SA1100_COLLIE
  65        pcmcia_collie_init,
  66 #endif
  67 };
  68
  69 static int sa11x0_drv_pcmcia_probe(struct device *dev)
  70 {
  71         int i, ret = -ENODEV;
  72
  73         /*
  74          * Initialise any "on-board" PCMCIA sockets.
  75          */
  76         for (i = 0; i < ARRAY_SIZE(sa11x0_pcmcia_hw_init); i++) {
  77                 ret = sa11x0_pcmcia_hw_init[i](dev);
  78                 if (ret == 0)
  79                         break;
  80         }
  81
  82         return ret;
  83 }
  84
  85 static struct device_driver sa11x0_pcmcia_driver = {
  86         .probe          = sa11x0_drv_pcmcia_probe,
  87         .remove         = soc_common_drv_pcmcia_remove,
  88         .name           = "sa11x0-pcmcia",
  89         .bus            = &platform_bus_type,
  90         .suspend        = pcmcia_socket_dev_suspend,
  91         .resume         = pcmcia_socket_dev_resume,
  92 };
  93
  94 /* sa11x0_pcmcia_init()
  95  * ^^^^^^^^^^^^^^^^^^^^
  96  *
  97  * This routine performs low-level PCMCIA initialization and then
  98  * registers this socket driver with Card Services.
  99  *
 100  * Returns: 0 on success, -ve error code on failure
 101  */
 102 static int __init sa11x0_pcmcia_init(void)
 103 {
 104         return driver_register(&sa11x0_pcmcia_driver);
 105 }
 106
 107 /* sa11x0_pcmcia_exit()
 108  * ^^^^^^^^^^^^^^^^^^^^
 109  * Invokes the low-level kernel service to free IRQs associated with this
 110  * socket controller and reset GPIO edge detection.
 111  */
 112 static void __exit sa11x0_pcmcia_exit(void)
 113 {
 114         driver_unregister(&sa11x0_pcmcia_driver);
 115 }
 116
 117 MODULE_AUTHOR("John Dorsey <john+@cs.cmu.edu>");
 118 MODULE_DESCRIPTION("Linux PCMCIA Card Services: SA-11x0 Socket Controller");
 119 MODULE_LICENSE("Dual MPL/GPL");
 120
 121 fs_initcall(sa11x0_pcmcia_init);
 122 module_exit(sa11x0_pcmcia_exit);