drivers/net/irda/irda-usb.c

   1 /*****************************************************************************
   2  *
   3  * Filename:      irda-usb.c
   4  * Version:       0.10
   5  * Description:   IrDA-USB Driver
   6  * Status:        Experimental
   7  * Author:        Dag Brattli <dag@brattli.net>
   8  *
   9  *      Copyright (C) 2000, Roman Weissgaerber <weissg@vienna.at>
  10  *      Copyright (C) 2001, Dag Brattli <dag@brattli.net>
  11  *      Copyright (C) 2001, Jean Tourrilhes <jt@hpl.hp.com>
  12  *      Copyright (C) 2004, SigmaTel, Inc. <irquality@sigmatel.com>
  13  *      Copyright (C) 2005, Milan Beno <beno@pobox.sk>
  14  *      Copyright (C) 2006, Nick Fedchik <nick@fedchik.org.ua>
  15  *
  16  *      This program is free software; you can redistribute it and/or modify
  17  *      it under the terms of the GNU General Public License as published by
  18  *      the Free Software Foundation; either version 2 of the License, or
  19  *      (at your option) any later version.
  20  *
  21  *      This program is distributed in the hope that it will be useful,
  22  *      but WITHOUT ANY WARRANTY; without even the implied warranty of
  23  *      MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  24  *      GNU General Public License for more details.
  25  *
  26  *      You should have received a copy of the GNU General Public License
  27  *      along with this program; if not, write to the Free Software
  28  *      Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  29  *
  30  *****************************************************************************/
  31
  32 /*
  33  *                          IMPORTANT NOTE
  34  *                          --------------
  35  *
  36  * As of kernel 2.5.20, this is the state of compliance and testing of
  37  * this driver (irda-usb) with regards to the USB low level drivers...
  38  *
  39  * This driver has been tested SUCCESSFULLY with the following drivers :
  40  *      o usb-uhci-hcd  (For Intel/Via USB controllers)
  41  *      o uhci-hcd      (Alternate/JE driver for Intel/Via USB controllers)
  42  *      o ohci-hcd      (For other USB controllers)
  43  *
  44  * This driver has NOT been tested with the following drivers :
  45  *      o ehci-hcd      (USB 2.0 controllers)
  46  *
  47  * Note that all HCD drivers do URB_ZERO_PACKET and timeout properly,
  48  * so we don't have to worry about that anymore.
  49  * One common problem is the failure to set the address on the dongle,
  50  * but this happens before the driver gets loaded...
  51  *
  52  * Jean II
  53  */
  54
  55 /*------------------------------------------------------------------*/
  56
  57 #include <linux/module.h>
  58 #include <linux/moduleparam.h>
  59 #include <linux/kernel.h>
  60 #include <linux/types.h>
  61 #include <linux/init.h>
  62 #include <linux/skbuff.h>
  63 #include <linux/netdevice.h>
  64 #include <linux/slab.h>
  65 #include <linux/rtnetlink.h>
  66 #include <linux/usb.h>
  67 #include <linux/firmware.h>
  68
  69 #include "irda-usb.h"
  70
  71 /*------------------------------------------------------------------*/
  72
  73 static int qos_mtt_bits = 0;
  74
  75 /* These are the currently known IrDA USB dongles. Add new dongles here */
  76 static struct usb_device_id dongles[] = {
  77         /* ACTiSYS Corp.,  ACT-IR2000U FIR-USB Adapter */
  78         { USB_DEVICE(0x9c4, 0x011), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  79         /* Look like ACTiSYS, Report : IBM Corp., IBM UltraPort IrDA */
  80         { USB_DEVICE(0x4428, 0x012), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  81         /* KC Technology Inc.,  KC-180 USB IrDA Device */
  82         { USB_DEVICE(0x50f, 0x180), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  83         /* Extended Systems, Inc.,  XTNDAccess IrDA USB (ESI-9685) */
  84         { USB_DEVICE(0x8e9, 0x100), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  85         /* SigmaTel STIR4210/4220/4116 USB IrDA (VFIR) Bridge */
  86         { USB_DEVICE(0x66f, 0x4210), .driver_info = IUC_STIR421X | IUC_SPEED_BUG },
  87         { USB_DEVICE(0x66f, 0x4220), .driver_info = IUC_STIR421X | IUC_SPEED_BUG },
  88         { USB_DEVICE(0x66f, 0x4116), .driver_info = IUC_STIR421X | IUC_SPEED_BUG },
  89         { .match_flags = USB_DEVICE_ID_MATCH_INT_CLASS |
  90           USB_DEVICE_ID_MATCH_INT_SUBCLASS,
  91           .bInterfaceClass = USB_CLASS_APP_SPEC,
  92           .bInterfaceSubClass = USB_CLASS_IRDA,
  93           .driver_info = IUC_DEFAULT, },
  94         { }, /* The end */
  95 };
  96
  97 /*
  98  * Important note :
  99  * Devices based on the SigmaTel chipset (0x66f, 0x4200) are not designed
 100  * using the "USB-IrDA specification" (yes, there exist such a thing), and
 101  * therefore not supported by this driver (don't add them above).
 102  * There is a Linux driver, stir4200, that support those USB devices.
 103  * Jean II
 104  */
 105
 106 MODULE_DEVICE_TABLE(usb, dongles);
 107
 108 /*------------------------------------------------------------------*/
 109
 110 static void irda_usb_init_qos(struct irda_usb_cb *self) ;
 111 static struct irda_class_desc *irda_usb_find_class_desc(struct usb_interface *intf);
 112 static void irda_usb_disconnect(struct usb_interface *intf);
 113 static void irda_usb_change_speed_xbofs(struct irda_usb_cb *self);
 114 static netdev_tx_t irda_usb_hard_xmit(struct sk_buff *skb,
 115                                             struct net_device *dev);
 116 static int irda_usb_open(struct irda_usb_cb *self);
 117 static void irda_usb_close(struct irda_usb_cb *self);
 118 static void speed_bulk_callback(struct urb *urb);
 119 static void write_bulk_callback(struct urb *urb);
 120 static void irda_usb_receive(struct urb *urb);
 121 static void irda_usb_rx_defer_expired(unsigned long data);
 122 static int irda_usb_net_open(struct net_device *dev);
 123 static int irda_usb_net_close(struct net_device *dev);
 124 static int irda_usb_net_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
 125 static void irda_usb_net_timeout(struct net_device *dev);
 126
 127 /************************ TRANSMIT ROUTINES ************************/
 128 /*
 129  * Receive packets from the IrDA stack and send them on the USB pipe.
 130  * Handle speed change, timeout and lot's of ugliness...
 131  */
 132
 133 /*------------------------------------------------------------------*/
 134 /*
 135  * Function irda_usb_build_header(self, skb, header)
 136  *
 137  *   Builds USB-IrDA outbound header
 138  *
 139  * When we send an IrDA frame over an USB pipe, we add to it a 1 byte
 140  * header. This function create this header with the proper values.
 141  *
 142  * Important note : the USB-IrDA spec 1.0 say very clearly in chapter 5.4.2.2
 143  * that the setting of the link speed and xbof number in this outbound header
 144  * should be applied *AFTER* the frame has been sent.
 145  * Unfortunately, some devices are not compliant with that... It seems that
 146  * reading the spec is far too difficult...
 147  * Jean II
 148  */
 149 static void irda_usb_build_header(struct irda_usb_cb *self,
 150                                   __u8 *header,
 151                                   int   force)
 152 {
 153         /* Here we check if we have an STIR421x chip,
 154          * and if either speed or xbofs (or both) needs
 155          * to be changed.
 156          */
 157         if (self->capability & IUC_STIR421X &&
 158             ((self->new_speed != -1) || (self->new_xbofs != -1))) {
 159
 160                 /* With STIR421x, speed and xBOFs must be set at the same
 161                  * time, even if only one of them changes.
 162                  */
 163                 if (self->new_speed == -1)
 164                         self->new_speed = self->speed ;
 165
 166                 if (self->new_xbofs == -1)
 167                         self->new_xbofs = self->xbofs ;
 168         }
 169
 170         /* Set the link speed */
 171         if (self->new_speed != -1) {
 172                 /* Hum... Ugly hack :-(
 173                  * Some device are not compliant with the spec and change
 174                  * parameters *before* sending the frame. - Jean II
 175                  */
 176                 if ((self->capability & IUC_SPEED_BUG) &&
 177                     (!force) && (self->speed != -1)) {
 178                         /* No speed and xbofs change here
 179                          * (we'll do it later in the write callback) */
 180                         IRDA_DEBUG(2, "%s(), not changing speed yet\n", __func__);
 181                         *header = 0;
 182                         return;
 183                 }
 184
 185                 IRDA_DEBUG(2, "%s(), changing speed to %d\n", __func__, self->new_speed);
 186                 self->speed = self->new_speed;
 187                 /* We will do ` self->new_speed = -1; ' in the completion
 188                  * handler just in case the current URB fail - Jean II */
 189
 190                 switch (self->speed) {
 191                 case 2400:
 192                         *header = SPEED_2400;
 193                         break;
 194                 default:
 195                 case 9600:
 196                         *header = SPEED_9600;
 197                         break;
 198                 case 19200:
 199                         *header = SPEED_19200;
 200                         break;
 201                 case 38400:
 202                         *header = SPEED_38400;
 203                         break;
 204                 case 57600:
 205                         *header = SPEED_57600;
 206                         break;
 207                 case 115200:
 208                         *header = SPEED_115200;
 209                         break;
 210                 case 576000:
 211                         *header = SPEED_576000;
 212                         break;
 213                 case 1152000:
 214                         *header = SPEED_1152000;
 215                         break;
 216                 case 4000000:
 217                         *header = SPEED_4000000;
 218                         self->new_xbofs = 0;
 219                         break;
 220                 case 16000000:
 221                         *header = SPEED_16000000;
 222                         self->new_xbofs = 0;
 223                         break;
 224                 }
 225         } else
 226                 /* No change */
 227                 *header = 0;
 228
 229         /* Set the negotiated additional XBOFS */
 230         if (self->new_xbofs != -1) {
 231                 IRDA_DEBUG(2, "%s(), changing xbofs to %d\n", __func__, self->new_xbofs);
 232                 self->xbofs = self->new_xbofs;
 233                 /* We will do ` self->new_xbofs = -1; ' in the completion
 234                  * handler just in case the current URB fail - Jean II */
 235
 236                 switch (self->xbofs) {
 237                 case 48:
 238                         *header |= 0x10;
 239                         break;
 240                 case 28:
 241                 case 24:        /* USB spec 1.0 says 24 */
 242                         *header |= 0x20;
 243                         break;
 244                 default:
 245                 case 12:
 246                         *header |= 0x30;
 247                         break;
 248                 case 5: /* Bug in IrLAP spec? (should be 6) */
 249                 case 6:
 250                         *header |= 0x40;
 251                         break;
 252                 case 3:
 253                         *header |= 0x50;
 254                         break;
 255                 case 2:
 256                         *header |= 0x60;
 257                         break;
 258                 case 1:
 259                         *header |= 0x70;
 260                         break;
 261                 case 0:
 262                         *header |= 0x80;
 263                         break;
 264                 }
 265         }
 266 }
 267
 268 /*
 269 *   calculate turnaround time for SigmaTel header
 270 */
 271 static __u8 get_turnaround_time(struct sk_buff *skb)
 272 {
 273         int turnaround_time = irda_get_mtt(skb);
 274
 275         if ( turnaround_time == 0 )
 276                 return 0;
 277         else if ( turnaround_time <= 10 )
 278                 return 1;
 279         else if ( turnaround_time <= 50 )
 280                 return 2;
 281         else if ( turnaround_time <= 100 )
 282                 return 3;
 283         else if ( turnaround_time <= 500 )
 284                 return 4;
 285         else if ( turnaround_time <= 1000 )
 286                 return 5;
 287         else if ( turnaround_time <= 5000 )
 288                 return 6;
 289         else
 290                 return 7;
 291 }
 292
 293
 294 /*------------------------------------------------------------------*/
 295 /*
 296  * Send a command to change the speed of the dongle
 297  * Need to be called with spinlock on.
 298  */
 299 static void irda_usb_change_speed_xbofs(struct irda_usb_cb *self)
 300 {
 301         __u8 *frame;
 302         struct urb *urb;
 303         int ret;
 304
 305         IRDA_DEBUG(2, "%s(), speed=%d, xbofs=%d\n", __func__,
 306                    self->new_speed, self->new_xbofs);
 307
 308         /* Grab the speed URB */
 309         urb = self->speed_urb;
 310         if (urb->status != 0) {
 311                 IRDA_WARNING("%s(), URB still in use!\n", __func__);
 312                 return;
 313         }
 314
 315         /* Allocate the fake frame */
 316         frame = self->speed_buff;
 317
 318         /* Set the new speed and xbofs in this fake frame */
 319         irda_usb_build_header(self, frame, 1);
 320
 321         if (self->capability & IUC_STIR421X) {
 322                 if (frame[0] == 0) return ; // do nothing if no change
 323                 frame[1] = 0; // other parameters don't change here
 324                 frame[2] = 0;
 325         }
 326
 327         /* Submit the 0 length IrDA frame to trigger new speed settings */
 328         usb_fill_bulk_urb(urb, self->usbdev,
 329                       usb_sndbulkpipe(self->usbdev, self->bulk_out_ep),
 330                       frame, IRDA_USB_SPEED_MTU,
 331                       speed_bulk_callback, self);
 332         urb->transfer_buffer_length = self->header_length;
 333         urb->transfer_flags = 0;
 334
 335         /* Irq disabled -> GFP_ATOMIC */
 336         if ((ret = usb_submit_urb(urb, GFP_ATOMIC))) {
 337                 IRDA_WARNING("%s(), failed Speed URB\n", __func__);
 338         }
 339 }
 340
 341 /*------------------------------------------------------------------*/
 342 /*
 343  * Speed URB callback
 344  * Now, we can only get called for the speed URB.
 345  */
 346 static void speed_bulk_callback(struct urb *urb)
 347 {
 348         struct irda_usb_cb *self = urb->context;
 349
 350         IRDA_DEBUG(2, "%s()\n", __func__);
 351
 352         /* We should always have a context */
 353         IRDA_ASSERT(self != NULL, return;);
 354         /* We should always be called for the speed URB */
 355         IRDA_ASSERT(urb == self->speed_urb, return;);
 356
 357         /* Check for timeout and other USB nasties */
 358         if (urb->status != 0) {
 359                 /* I get a lot of -ECONNABORTED = -103 here - Jean II */
 360                 IRDA_DEBUG(0, "%s(), URB complete status %d, transfer_flags 0x%04X\n", __func__, urb->status, urb->transfer_flags);
 361
 362                 /* Don't do anything here, that might confuse the USB layer.
 363                  * Instead, we will wait for irda_usb_net_timeout(), the
 364                  * network layer watchdog, to fix the situation.
 365                  * Jean II */
 366                 /* A reset of the dongle might be welcomed here - Jean II */
 367                 return;
 368         }
 369
 370         /* urb is now available */
 371         //urb->status = 0; -> tested above
 372
 373         /* New speed and xbof is now commited in hardware */
 374         self->new_speed = -1;
 375         self->new_xbofs = -1;
 376
 377         /* Allow the stack to send more packets */
 378         netif_wake_queue(self->netdev);
 379 }
 380
 381 /*------------------------------------------------------------------*/
 382 /*
 383  * Send an IrDA frame to the USB dongle (for transmission)
 384  */
 385 static netdev_tx_t irda_usb_hard_xmit(struct sk_buff *skb,
 386                                             struct net_device *netdev)
 387 {
 388         struct irda_usb_cb *self = netdev_priv(netdev);
 389         struct urb *urb = self->tx_urb;
 390         unsigned long flags;
 391         s32 speed;
 392         s16 xbofs;
 393         int res, mtt;
 394
 395         IRDA_DEBUG(4, "%s() on %s\n", __func__, netdev->name);
 396
 397         netif_stop_queue(netdev);
 398
 399         /* Protect us from USB callbacks, net watchdog and else. */
 400         spin_lock_irqsave(&self->lock, flags);
 401
 402         /* Check if the device is still there.
 403          * We need to check self->present under the spinlock because
 404          * of irda_usb_disconnect() is synchronous - Jean II */
 405         if (!self->present) {
 406                 IRDA_DEBUG(0, "%s(), Device is gone...\n", __func__);
 407                 goto drop;
 408         }
 409
 410         /* Check if we need to change the number of xbofs */
 411         xbofs = irda_get_next_xbofs(skb);
 412         if ((xbofs != self->xbofs) && (xbofs != -1)) {
 413                 self->new_xbofs = xbofs;
 414         }
 415
 416         /* Check if we need to change the speed */
 417         speed = irda_get_next_speed(skb);
 418         if ((speed != self->speed) && (speed != -1)) {
 419                 /* Set the desired speed */
 420                 self->new_speed = speed;
 421
 422                 /* Check for empty frame */
 423                 if (!skb->len) {
 424                         /* IrLAP send us an empty frame to make us change the
 425                          * speed. Changing speed with the USB adapter is in
 426                          * fact sending an empty frame to the adapter, so we
 427                          * could just let the present function do its job.
 428                          * However, we would wait for min turn time,
 429                          * do an extra memcpy and increment packet counters...
 430                          * Jean II */
 431                         irda_usb_change_speed_xbofs(self);
 432                         netdev->trans_start = jiffies;
 433                         /* Will netif_wake_queue() in callback */
 434                         goto drop;
 435                 }
 436         }
 437
 438         if (urb->status != 0) {
 439                 IRDA_WARNING("%s(), URB still in use!\n", __func__);
 440                 goto drop;
 441         }
 442
 443         skb_copy_from_linear_data(skb, self->tx_buff + self->header_length, skb->len);
 444
 445         /* Change setting for next frame */
 446         if (self->capability & IUC_STIR421X) {
 447                 __u8 turnaround_time;
 448                 __u8* frame = self->tx_buff;
 449                 turnaround_time = get_turnaround_time( skb );
 450                 irda_usb_build_header(self, frame, 0);
 451                 frame[2] = turnaround_time;
 452                 if ((skb->len != 0) &&
 453                     ((skb->len % 128) == 0) &&
 454                     ((skb->len % 512) != 0)) {
 455                         /* add extra byte for special SigmaTel feature */
 456                         frame[1] = 1;
 457                         skb_put(skb, 1);
 458                 } else {
 459                         frame[1] = 0;
 460                 }
 461         } else {
 462                 irda_usb_build_header(self, self->tx_buff, 0);
 463         }
 464
 465         /* FIXME: Make macro out of this one */
 466         ((struct irda_skb_cb *)skb->cb)->context = self;
 467
 468         usb_fill_bulk_urb(urb, self->usbdev,
 469                       usb_sndbulkpipe(self->usbdev, self->bulk_out_ep),
 470                       self->tx_buff, skb->len + self->header_length,
 471                       write_bulk_callback, skb);
 472
 473         /* This flag (URB_ZERO_PACKET) indicates that what we send is not
 474          * a continuous stream of data but separate packets.
 475          * In this case, the USB layer will insert an empty USB frame (TD)
 476          * after each of our packets that is exact multiple of the frame size.
 477          * This is how the dongle will detect the end of packet - Jean II */
 478         urb->transfer_flags = URB_ZERO_PACKET;
 479
 480         /* Generate min turn time. FIXME: can we do better than this? */
 481         /* Trying to a turnaround time at this level is trying to measure
 482          * processor clock cycle with a wrist-watch, approximate at best...
 483          *
 484          * What we know is the last time we received a frame over USB.
 485          * Due to latency over USB that depend on the USB load, we don't
 486          * know when this frame was received over IrDA (a few ms before ?)
 487          * Then, same story for our outgoing frame...
 488          *
 489          * In theory, the USB dongle is supposed to handle the turnaround
 490          * by itself (spec 1.0, chater 4, page 6). Who knows ??? That's
 491          * why this code is enabled only for dongles that doesn't meet
 492          * the spec.
 493          * Jean II */
 494         if (self->capability & IUC_NO_TURN) {
 495                 mtt = irda_get_mtt(skb);
 496                 if (mtt) {
 497                         int diff;
 498                         do_gettimeofday(&self->now);
 499                         diff = self->now.tv_usec - self->stamp.tv_usec;
 500 #ifdef IU_USB_MIN_RTT
 501                         /* Factor in USB delays -> Get rid of udelay() that
 502                          * would be lost in the noise - Jean II */
 503                         diff += IU_USB_MIN_RTT;
 504 #endif /* IU_USB_MIN_RTT */
 505                         /* If the usec counter did wraparound, the diff will
 506                          * go negative (tv_usec is a long), so we need to
 507                          * correct it by one second. Jean II */
 508                         if (diff < 0)
 509                                 diff += 1000000;
 510
 511                         /* Check if the mtt is larger than the time we have
 512                          * already used by all the protocol processing
 513                          */
 514                         if (mtt > diff) {
 515                                 mtt -= diff;
 516                                 if (mtt > 1000)
 517                                         mdelay(mtt/1000);
 518                                 else
 519                                         udelay(mtt);
 520                         }
 521                 }
 522         }
 523
 524         /* Ask USB to send the packet - Irq disabled -> GFP_ATOMIC */
 525         if ((res = usb_submit_urb(urb, GFP_ATOMIC))) {
 526                 IRDA_WARNING("%s(), failed Tx URB\n", __func__);
 527                 netdev->stats.tx_errors++;
 528                 /* Let USB recover : We will catch that in the watchdog */
 529                 /*netif_start_queue(netdev);*/
 530         } else {
 531                 /* Increment packet stats */
 532                 netdev->stats.tx_packets++;
 533                 netdev->stats.tx_bytes += skb->len;
 534
 535                 netdev->trans_start = jiffies;
 536         }
 537         spin_unlock_irqrestore(&self->lock, flags);
 538
 539         return NETDEV_TX_OK;
 540
 541 drop:
 542         /* Drop silently the skb and exit */
 543         dev_kfree_skb(skb);
 544         spin_unlock_irqrestore(&self->lock, flags);
 545         return NETDEV_TX_OK;
 546 }
 547
 548 /*------------------------------------------------------------------*/
 549 /*
 550  * Note : this function will be called only for tx_urb...
 551  */
 552 static void write_bulk_callback(struct urb *urb)
 553 {
 554         unsigned long flags;
 555         struct sk_buff *skb = urb->context;
 556         struct irda_usb_cb *self = ((struct irda_skb_cb *) skb->cb)->context;
 557
 558         IRDA_DEBUG(2, "%s()\n", __func__);
 559
 560         /* We should always have a context */
 561         IRDA_ASSERT(self != NULL, return;);
 562         /* We should always be called for the speed URB */
 563         IRDA_ASSERT(urb == self->tx_urb, return;);
 564
 565         /* Free up the skb */
 566         dev_kfree_skb_any(skb);
 567         urb->context = NULL;
 568
 569         /* Check for timeout and other USB nasties */
 570         if (urb->status != 0) {
 571                 /* I get a lot of -ECONNABORTED = -103 here - Jean II */
 572                 IRDA_DEBUG(0, "%s(), URB complete status %d, transfer_flags 0x%04X\n", __func__, urb->status, urb->transfer_flags);
 573
 574                 /* Don't do anything here, that might confuse the USB layer,
 575                  * and we could go in recursion and blow the kernel stack...
 576                  * Instead, we will wait for irda_usb_net_timeout(), the
 577                  * network layer watchdog, to fix the situation.
 578                  * Jean II */
 579                 /* A reset of the dongle might be welcomed here - Jean II */
 580                 return;
 581         }
 582
 583         /* urb is now available */
 584         //urb->status = 0; -> tested above
 585
 586         /* Make sure we read self->present properly */
 587         spin_lock_irqsave(&self->lock, flags);
 588
 589         /* If the network is closed, stop everything */
 590         if ((!self->netopen) || (!self->present)) {
 591                 IRDA_DEBUG(0, "%s(), Network is gone...\n", __func__);
 592                 spin_unlock_irqrestore(&self->lock, flags);
 593                 return;
 594         }
 595
 596         /* If changes to speed or xbofs is pending... */
 597         if ((self->new_speed != -1) || (self->new_xbofs != -1)) {
 598                 if ((self->new_speed != self->speed) ||
 599                     (self->new_xbofs != self->xbofs)) {
 600                         /* We haven't changed speed yet (because of
 601                          * IUC_SPEED_BUG), so do it now - Jean II */
 602                         IRDA_DEBUG(1, "%s(), Changing speed now...\n", __func__);
 603                         irda_usb_change_speed_xbofs(self);
 604                 } else {
 605                         /* New speed and xbof is now commited in hardware */
 606                         self->new_speed = -1;
 607                         self->new_xbofs = -1;
 608                         /* Done, waiting for next packet */
 609                         netif_wake_queue(self->netdev);
 610                 }
 611         } else {
 612                 /* Otherwise, allow the stack to send more packets */
 613                 netif_wake_queue(self->netdev);
 614         }
 615         spin_unlock_irqrestore(&self->lock, flags);
 616 }
 617
 618 /*------------------------------------------------------------------*/
 619 /*
 620  * Watchdog timer from the network layer.
 621  * After a predetermined timeout, if we don't give confirmation that
 622  * the packet has been sent (i.e. no call to netif_wake_queue()),
 623  * the network layer will call this function.
 624  * Note that URB that we submit have also a timeout. When the URB timeout
 625  * expire, the normal URB callback is called (write_bulk_callback()).
 626  */
 627 static void irda_usb_net_timeout(struct net_device *netdev)
 628 {
 629         unsigned long flags;
 630         struct irda_usb_cb *self = netdev_priv(netdev);
 631         struct urb *urb;
 632         int     done = 0;       /* If we have made any progress */
 633
 634         IRDA_DEBUG(0, "%s(), Network layer thinks we timed out!\n", __func__);
 635         IRDA_ASSERT(self != NULL, return;);
 636
 637         /* Protect us from USB callbacks, net Tx and else. */
 638         spin_lock_irqsave(&self->lock, flags);
 639
 640         /* self->present *MUST* be read under spinlock */
 641         if (!self->present) {
 642                 IRDA_WARNING("%s(), device not present!\n", __func__);
 643                 netif_stop_queue(netdev);
 644                 spin_unlock_irqrestore(&self->lock, flags);
 645                 return;
 646         }
 647
 648         /* Check speed URB */
 649         urb = self->speed_urb;
 650         if (urb->status != 0) {
 651                 IRDA_DEBUG(0, "%s: Speed change timed out, urb->status=%d, urb->transfer_flags=0x%04X\n", netdev->name, urb->status, urb->transfer_flags);
 652
 653                 switch (urb->status) {
 654                 case -EINPROGRESS:
 655                         usb_unlink_urb(urb);
 656                         /* Note : above will  *NOT* call netif_wake_queue()
 657                          * in completion handler, we will come back here.
 658                          * Jean II */
 659                         done = 1;
 660                         break;
 661                 case -ECONNRESET:
 662                 case -ENOENT:                   /* urb unlinked by us */
 663                 default:                        /* ??? - Play safe */
 664                         urb->status = 0;
 665                         netif_wake_queue(self->netdev);
 666                         done = 1;
 667                         break;
 668                 }
 669         }
 670
 671         /* Check Tx URB */
 672         urb = self->tx_urb;
 673         if (urb->status != 0) {
 674                 struct sk_buff *skb = urb->context;
 675
 676                 IRDA_DEBUG(0, "%s: Tx timed out, urb->status=%d, urb->transfer_flags=0x%04X\n", netdev->name, urb->status, urb->transfer_flags);
 677
 678                 /* Increase error count */
 679                 netdev->stats.tx_errors++;
 680
 681 #ifdef IU_BUG_KICK_TIMEOUT
 682                 /* Can't be a bad idea to reset the speed ;-) - Jean II */
 683                 if(self->new_speed == -1)
 684                         self->new_speed = self->speed;
 685                 if(self->new_xbofs == -1)
 686                         self->new_xbofs = self->xbofs;
 687                 irda_usb_change_speed_xbofs(self);
 688 #endif /* IU_BUG_KICK_TIMEOUT */
 689
 690                 switch (urb->status) {
 691                 case -EINPROGRESS:
 692                         usb_unlink_urb(urb);
 693                         /* Note : above will  *NOT* call netif_wake_queue()
 694                          * in completion handler, because urb->status will
 695                          * be -ENOENT. We will fix that at the next watchdog,
 696                          * leaving more time to USB to recover...
 697                          * Jean II */
 698                         done = 1;
 699                         break;
 700                 case -ECONNRESET:
 701                 case -ENOENT:                   /* urb unlinked by us */
 702                 default:                        /* ??? - Play safe */
 703                         if(skb != NULL) {
 704                                 dev_kfree_skb_any(skb);
 705                                 urb->context = NULL;
 706                         }
 707                         urb->status = 0;
 708                         netif_wake_queue(self->netdev);
 709                         done = 1;
 710                         break;
 711                 }
 712         }
 713         spin_unlock_irqrestore(&self->lock, flags);
 714
 715         /* Maybe we need a reset */
 716         /* Note : Some drivers seem to use a usb_set_interface() when they
 717          * need to reset the hardware. Hum...
 718          */
 719
 720         /* if(done == 0) */
 721 }
 722
 723 /************************* RECEIVE ROUTINES *************************/
 724 /*
 725  * Receive packets from the USB layer stack and pass them to the IrDA stack.
 726  * Try to work around USB failures...
 727  */
 728
 729 /*
 730  * Note :
 731  * Some of you may have noticed that most dongle have an interrupt in pipe
 732  * that we don't use. Here is the little secret...
 733  * When we hang a Rx URB on the bulk in pipe, it generates some USB traffic
 734  * in every USB frame. This is unnecessary overhead.
 735  * The interrupt in pipe will generate an event every time a packet is
 736  * received. Reading an interrupt pipe adds minimal overhead, but has some
 737  * latency (~1ms).
 738  * If we are connected (speed != 9600), we want to minimise latency, so
 739  * we just always hang the Rx URB and ignore the interrupt.
 740  * If we are not connected (speed == 9600), there is usually no Rx traffic,
 741  * and we want to minimise the USB overhead. In this case we should wait
 742  * on the interrupt pipe and hang the Rx URB only when an interrupt is
 743  * received.
 744  * Jean II
 745  *
 746  * Note : don't read the above as what we are currently doing, but as
 747  * something we could do with KC dongle. Also don't forget that the
 748  * interrupt pipe is not part of the original standard, so this would
 749  * need to be optional...
 750  * Jean II
 751  */
 752
 753 /*------------------------------------------------------------------*/
 754 /*
 755  * Submit a Rx URB to the USB layer to handle reception of a frame
 756  * Mostly called by the completion callback of the previous URB.
 757  *
 758  * Jean II
 759  */
 760 static void irda_usb_submit(struct irda_usb_cb *self, struct sk_buff *skb, struct urb *urb)
 761 {
 762         struct irda_skb_cb *cb;
 763         int ret;
 764
 765         IRDA_DEBUG(2, "%s()\n", __func__);
 766
 767         /* This should never happen */
 768         IRDA_ASSERT(skb != NULL, return;);
 769         IRDA_ASSERT(urb != NULL, return;);
 770
 771         /* Save ourselves in the skb */
 772         cb = (struct irda_skb_cb *) skb->cb;
 773         cb->context = self;
 774
 775         /* Reinitialize URB */
 776         usb_fill_bulk_urb(urb, self->usbdev,
 777                       usb_rcvbulkpipe(self->usbdev, self->bulk_in_ep),
 778                       skb->data, IRDA_SKB_MAX_MTU,
 779                       irda_usb_receive, skb);
 780         urb->status = 0;
 781
 782         /* Can be called from irda_usb_receive (irq handler) -> GFP_ATOMIC */
 783         ret = usb_submit_urb(urb, GFP_ATOMIC);
 784         if (ret) {
 785                 /* If this ever happen, we are in deep s***.
 786                  * Basically, the Rx path will stop... */
 787                 IRDA_WARNING("%s(), Failed to submit Rx URB %d\n",
 788                              __func__, ret);
 789         }
 790 }
 791
 792 /*------------------------------------------------------------------*/
 793 /*
 794  * Function irda_usb_receive(urb)
 795  *
 796  *     Called by the USB subsystem when a frame has been received
 797  *
 798  */
 799 static void irda_usb_receive(struct urb *urb)
 800 {
 801         struct sk_buff *skb = (struct sk_buff *) urb->context;
 802         struct irda_usb_cb *self;
 803         struct irda_skb_cb *cb;
 804         struct sk_buff *newskb;
 805         struct sk_buff *dataskb;
 806         struct urb *next_urb;
 807         unsigned int len, docopy;
 808
 809         IRDA_DEBUG(2, "%s(), len=%d\n", __func__, urb->actual_length);
 810
 811         /* Find ourselves */
 812         cb = (struct irda_skb_cb *) skb->cb;
 813         IRDA_ASSERT(cb != NULL, return;);
 814         self = (struct irda_usb_cb *) cb->context;
 815         IRDA_ASSERT(self != NULL, return;);
 816
 817         /* If the network is closed or the device gone, stop everything */
 818         if ((!self->netopen) || (!self->present)) {
 819                 IRDA_DEBUG(0, "%s(), Network is gone!\n", __func__);
 820                 /* Don't re-submit the URB : will stall the Rx path */
 821                 return;
 822         }
 823
 824         /* Check the status */
 825         if (urb->status != 0) {
 826                 switch (urb->status) {
 827                 case -EILSEQ:
 828                         self->netdev->stats.rx_crc_errors++;
 829                         /* Also precursor to a hot-unplug on UHCI. */
 830                         /* Fallthrough... */
 831                 case -ECONNRESET:
 832                         /* Random error, if I remember correctly */
 833                         /* uhci_cleanup_unlink() is going to kill the Rx
 834                          * URB just after we return. No problem, at this
 835                          * point the URB will be idle ;-) - Jean II */
 836                 case -ESHUTDOWN:
 837                         /* That's usually a hot-unplug. Submit will fail... */
 838                 case -ETIME:
 839                         /* Usually precursor to a hot-unplug on OHCI. */
 840                 default:
 841                         self->netdev->stats.rx_errors++;
 842                         IRDA_DEBUG(0, "%s(), RX status %d, transfer_flags 0x%04X \n", __func__, urb->status, urb->transfer_flags);
 843                         break;
 844                 }
 845                 /* If we received an error, we don't want to resubmit the
 846                  * Rx URB straight away but to give the USB layer a little
 847                  * bit of breathing room.
 848                  * We are in the USB thread context, therefore there is a
 849                  * danger of recursion (new URB we submit fails, we come
 850                  * back here).
 851                  * With recent USB stack (2.6.15+), I'm seeing that on
 852                  * hot unplug of the dongle...
 853                  * Lowest effective timer is 10ms...
 854                  * Jean II */
 855                 self->rx_defer_timer.function = &irda_usb_rx_defer_expired;
 856                 self->rx_defer_timer.data = (unsigned long) urb;
 857                 mod_timer(&self->rx_defer_timer, jiffies + (10 * HZ / 1000));
 858                 return;
 859         }
 860
 861         /* Check for empty frames */
 862         if (urb->actual_length <= self->header_length) {
 863                 IRDA_WARNING("%s(), empty frame!\n", __func__);
 864                 goto done;
 865         }
 866
 867         /*
 868          * Remember the time we received this frame, so we can
 869          * reduce the min turn time a bit since we will know
 870          * how much time we have used for protocol processing
 871          */
 872         do_gettimeofday(&self->stamp);
 873
 874         /* Check if we need to copy the data to a new skb or not.
 875          * For most frames, we use ZeroCopy and pass the already
 876          * allocated skb up the stack.
 877          * If the frame is small, it is more efficient to copy it
 878          * to save memory (copy will be fast anyway - that's
 879          * called Rx-copy-break). Jean II */
 880         docopy = (urb->actual_length < IRDA_RX_COPY_THRESHOLD);
 881
 882         /* Allocate a new skb */
 883         if (self->capability & IUC_STIR421X)
 884                 newskb = dev_alloc_skb(docopy ? urb->actual_length :
 885                                        IRDA_SKB_MAX_MTU +
 886                                        USB_IRDA_STIR421X_HEADER);
 887         else
 888                 newskb = dev_alloc_skb(docopy ? urb->actual_length :
 889                                        IRDA_SKB_MAX_MTU);
 890
 891         if (!newskb)  {
 892                 self->netdev->stats.rx_dropped++;
 893                 /* We could deliver the current skb, but this would stall
 894                  * the Rx path. Better drop the packet... Jean II */
 895                 goto done;
 896         }
 897
 898         /* Make sure IP header get aligned (IrDA header is 5 bytes) */
 899         /* But IrDA-USB header is 1 byte. Jean II */
 900         //skb_reserve(newskb, USB_IRDA_HEADER - 1);
 901
 902         if(docopy) {
 903                 /* Copy packet, so we can recycle the original */
 904                 skb_copy_from_linear_data(skb, newskb->data, urb->actual_length);
 905                 /* Deliver this new skb */
 906                 dataskb = newskb;
 907                 /* And hook the old skb to the URB
 908                  * Note : we don't need to "clean up" the old skb,
 909                  * as we never touched it. Jean II */
 910         } else {
 911                 /* We are using ZeroCopy. Deliver old skb */
 912                 dataskb = skb;
 913                 /* And hook the new skb to the URB */
 914                 skb = newskb;
 915         }
 916
 917         /* Set proper length on skb & remove USB-IrDA header */
 918         skb_put(dataskb, urb->actual_length);
 919         skb_pull(dataskb, self->header_length);
 920
 921         /* Ask the networking layer to queue the packet for the IrDA stack */
 922         dataskb->dev = self->netdev;
 923         skb_reset_mac_header(dataskb);
 924         dataskb->protocol = htons(ETH_P_IRDA);
 925         len = dataskb->len;
 926         netif_rx(dataskb);
 927
 928         /* Keep stats up to date */
 929         self->netdev->stats.rx_bytes += len;
 930         self->netdev->stats.rx_packets++;
 931
 932 done:
 933         /* Note : at this point, the URB we've just received (urb)
 934          * is still referenced by the USB layer. For example, if we
 935          * have received a -ECONNRESET, uhci_cleanup_unlink() will
 936          * continue to process it (in fact, cleaning it up).
 937          * If we were to submit this URB, disaster would ensue.
 938          * Therefore, we submit our idle URB, and put this URB in our
 939          * idle slot....
 940          * Jean II */
 941         /* Note : with this scheme, we could submit the idle URB before
 942          * processing the Rx URB. I don't think it would buy us anything as
 943          * we are running in the USB thread context. Jean II */
 944         next_urb = self->idle_rx_urb;
 945
 946         /* Recycle Rx URB : Now, the idle URB is the present one */
 947         urb->context = NULL;
 948         self->idle_rx_urb = urb;
 949
 950         /* Submit the idle URB to replace the URB we've just received.
 951          * Do it last to avoid race conditions... Jean II */
 952         irda_usb_submit(self, skb, next_urb);
 953 }
 954
 955 /*------------------------------------------------------------------*/
 956 /*
 957  * In case of errors, we want the USB layer to have time to recover.
 958  * Now, it is time to resubmit ouur Rx URB...
 959  */
 960 static void irda_usb_rx_defer_expired(unsigned long data)
 961 {
 962         struct urb *urb = (struct urb *) data;
 963         struct sk_buff *skb = (struct sk_buff *) urb->context;
 964         struct irda_usb_cb *self;
 965         struct irda_skb_cb *cb;
 966         struct urb *next_urb;
 967
 968         IRDA_DEBUG(2, "%s()\n", __func__);
 969
 970         /* Find ourselves */
 971         cb = (struct irda_skb_cb *) skb->cb;
 972         IRDA_ASSERT(cb != NULL, return;);
 973         self = (struct irda_usb_cb *) cb->context;
 974         IRDA_ASSERT(self != NULL, return;);
 975
 976         /* Same stuff as when Rx is done, see above... */
 977         next_urb = self->idle_rx_urb;
 978         urb->context = NULL;
 979         self->idle_rx_urb = urb;
 980         irda_usb_submit(self, skb, next_urb);
 981 }
 982
 983 /*------------------------------------------------------------------*/
 984 /*
 985  * Callbak from IrDA layer. IrDA wants to know if we have
 986  * started receiving anything.
 987  */
 988 static int irda_usb_is_receiving(struct irda_usb_cb *self)
 989 {
 990         /* Note : because of the way UHCI works, it's almost impossible
 991          * to get this info. The Controller DMA directly to memory and
 992          * signal only when the whole frame is finished. To know if the
 993          * first TD of the URB has been filled or not seems hard work...
 994          *
 995          * The other solution would be to use the "receiving" command
 996          * on the default decriptor with a usb_control_msg(), but that
 997          * would add USB traffic and would return result only in the
 998          * next USB frame (~1ms).
 999          *
1000          * I've been told that current dongles send status info on their
1001          * interrupt endpoint, and that's what the Windows driver uses
1002          * to know this info. Unfortunately, this is not yet in the spec...
1003          *
1004          * Jean II
1005          */
1006
1007         return 0; /* For now */
1008 }
1009
1010 #define STIR421X_PATCH_PRODUCT_VER     "Product Version: "
1011 #define STIR421X_PATCH_STMP_TAG        "STMP"
1012 #define STIR421X_PATCH_CODE_OFFSET     512 /* patch image starts before here */
1013 /* marks end of patch file header (PC DOS text file EOF character) */
1014 #define STIR421X_PATCH_END_OF_HDR_TAG  0x1A
1015 #define STIR421X_PATCH_BLOCK_SIZE      1023
1016
1017 /*
1018  * Function stir421x_fwupload (struct irda_usb_cb *self,
1019  *                             unsigned char *patch,
1020  *                             const unsigned int patch_len)
1021  *
1022  *   Upload firmware code to SigmaTel 421X IRDA-USB dongle
1023  */
1024 static int stir421x_fw_upload(struct irda_usb_cb *self,
1025                              const unsigned char *patch,
1026                              const unsigned int patch_len)
1027 {
1028         int ret = -ENOMEM;
1029         int actual_len = 0;
1030         unsigned int i;
1031         unsigned int block_size = 0;
1032         unsigned char *patch_block;
1033
1034         patch_block = kzalloc(STIR421X_PATCH_BLOCK_SIZE, GFP_KERNEL);
1035         if (patch_block == NULL)
1036                 return -ENOMEM;
1037
1038         /* break up patch into 1023-byte sections */
1039         for (i = 0; i < patch_len; i += block_size) {
1040                 block_size = patch_len - i;
1041
1042                 if (block_size > STIR421X_PATCH_BLOCK_SIZE)
1043                         block_size = STIR421X_PATCH_BLOCK_SIZE;
1044
1045                 /* upload the patch section */
1046                 memcpy(patch_block, patch + i, block_size);
1047
1048                 ret = usb_bulk_msg(self->usbdev,
1049                                    usb_sndbulkpipe(self->usbdev,
1050                                                    self->bulk_out_ep),
1051                                    patch_block, block_size,
1052                                    &actual_len, msecs_to_jiffies(500));
1053                 IRDA_DEBUG(3,"%s(): Bulk send %u bytes, ret=%d\n",
1054                            __func__, actual_len, ret);
1055
1056                 if (ret < 0)
1057                         break;
1058
1059                 mdelay(10);
1060         }
1061
1062         kfree(patch_block);
1063
1064         return ret;
1065  }
1066
1067 /*
1068  * Function stir421x_patch_device(struct irda_usb_cb *self)
1069  *
1070  * Get a firmware code from userspase using hotplug request_firmware() call
1071   */
1072 static int stir421x_patch_device(struct irda_usb_cb *self)
1073 {
1074         unsigned int i;
1075         int ret;
1076         char stir421x_fw_name[12];
1077         const struct firmware *fw;
1078         const unsigned char *fw_version_ptr; /* pointer to version string */
1079         unsigned long fw_version = 0;
1080
1081         /*
1082          * Known firmware patch file names for STIR421x dongles
1083          * are "42101001.sb" or "42101002.sb"
1084          */
1085         sprintf(stir421x_fw_name, "4210%4X.sb",
1086                 self->usbdev->descriptor.bcdDevice);
1087         ret = request_firmware(&fw, stir421x_fw_name, &self->usbdev->dev);
1088         if (ret < 0)
1089                 return ret;
1090
1091         /* We get a patch from userspace */
1092         IRDA_MESSAGE("%s(): Received firmware %s (%zu bytes)\n",
1093                      __func__, stir421x_fw_name, fw->size);
1094
1095         ret = -EINVAL;
1096
1097         /* Get the bcd product version */
1098         if (!memcmp(fw->data, STIR421X_PATCH_PRODUCT_VER,
1099                     sizeof(STIR421X_PATCH_PRODUCT_VER) - 1)) {
1100                 fw_version_ptr = fw->data +
1101                         sizeof(STIR421X_PATCH_PRODUCT_VER) - 1;
1102
1103                 /* Let's check if the product version is dotted */
1104                 if (fw_version_ptr[3] == '.' &&
1105                     fw_version_ptr[7] == '.') {
1106                         unsigned long major, minor, build;
1107                         major = simple_strtoul(fw_version_ptr, NULL, 10);
1108                         minor = simple_strtoul(fw_version_ptr + 4, NULL, 10);
1109                         build = simple_strtoul(fw_version_ptr + 8, NULL, 10);
1110
1111                         fw_version = (major << 12)
1112                                 + (minor << 8)
1113                                 + ((build / 10) << 4)
1114                                 + (build % 10);
1115
1116                         IRDA_DEBUG(3, "%s(): Firmware Product version %ld\n",
1117                                    __func__, fw_version);
1118                 }
1119         }
1120
1121         if (self->usbdev->descriptor.bcdDevice == cpu_to_le16(fw_version)) {
1122                 /*
1123                  * If we're here, we've found a correct patch
1124                  * The actual image starts after the "STMP" keyword
1125                  * so forward to the firmware header tag
1126                  */
1127                 for (i = 0; (fw->data[i] != STIR421X_PATCH_END_OF_HDR_TAG)
1128                              && (i < fw->size); i++) ;
1129                 /* here we check for the out of buffer case */
1130                 if ((STIR421X_PATCH_END_OF_HDR_TAG == fw->data[i])
1131                     && (i < STIR421X_PATCH_CODE_OFFSET)) {
1132                         if (!memcmp(fw->data + i + 1, STIR421X_PATCH_STMP_TAG,
1133                                     sizeof(STIR421X_PATCH_STMP_TAG) - 1)) {
1134
1135                                 /* We can upload the patch to the target */
1136                                 i += sizeof(STIR421X_PATCH_STMP_TAG);
1137                                 ret = stir421x_fw_upload(self, &fw->data[i],
1138                                                          fw->size - i);
1139                         }
1140                 }
1141         }
1142
1143         release_firmware(fw);
1144
1145         return ret;
1146 }
1147
1148
1149 /********************** IRDA DEVICE CALLBACKS **********************/
1150 /*
1151  * Main calls from the IrDA/Network subsystem.
1152  * Mostly registering a new irda-usb device and removing it....
1153  * We only deal with the IrDA side of the business, the USB side will
1154  * be dealt with below...
1155  */
1156
1157
1158 /*------------------------------------------------------------------*/
1159 /*
1160  * Function irda_usb_net_open (dev)
1161  *
1162  *    Network device is taken up. Usually this is done by "ifconfig irda0 up"
1163  *
1164  * Note : don't mess with self->netopen - Jean II
1165  */
1166 static int irda_usb_net_open(struct net_device *netdev)
1167 {
1168         struct irda_usb_cb *self;
1169         unsigned long flags;
1170         char    hwname[16];
1171         int i;
1172
1173         IRDA_DEBUG(1, "%s()\n", __func__);
1174
1175         IRDA_ASSERT(netdev != NULL, return -1;);
1176         self = netdev_priv(netdev);
1177         IRDA_ASSERT(self != NULL, return -1;);
1178
1179         spin_lock_irqsave(&self->lock, flags);
1180         /* Can only open the device if it's there */
1181         if(!self->present) {
1182                 spin_unlock_irqrestore(&self->lock, flags);
1183                 IRDA_WARNING("%s(), device not present!\n", __func__);
1184                 return -1;
1185         }
1186
1187         if(self->needspatch) {
1188                 spin_unlock_irqrestore(&self->lock, flags);
1189                 IRDA_WARNING("%s(), device needs patch\n", __func__) ;
1190                 return -EIO ;
1191         }
1192
1193         /* Initialise default speed and xbofs value
1194          * (IrLAP will change that soon) */
1195         self->speed = -1;
1196         self->xbofs = -1;
1197         self->new_speed = -1;
1198         self->new_xbofs = -1;
1199
1200         /* To do *before* submitting Rx urbs and starting net Tx queue
1201          * Jean II */
1202         self->netopen = 1;
1203         spin_unlock_irqrestore(&self->lock, flags);
1204
1205         /*
1206          * Now that everything should be initialized properly,
1207          * Open new IrLAP layer instance to take care of us...
1208          * Note : will send immediately a speed change...
1209          */
1210         sprintf(hwname, "usb#%d", self->usbdev->devnum);
1211         self->irlap = irlap_open(netdev, &self->qos, hwname);
1212         IRDA_ASSERT(self->irlap != NULL, return -1;);
1213
1214         /* Allow IrLAP to send data to us */
1215         netif_start_queue(netdev);
1216
1217         /* We submit all the Rx URB except for one that we keep idle.
1218          * Need to be initialised before submitting other USBs, because
1219          * in some cases as soon as we submit the URBs the USB layer
1220          * will trigger a dummy receive - Jean II */
1221         self->idle_rx_urb = self->rx_urb[IU_MAX_ACTIVE_RX_URBS];
1222         self->idle_rx_urb->context = NULL;
1223
1224         /* Now that we can pass data to IrLAP, allow the USB layer
1225          * to send us some data... */
1226         for (i = 0; i < IU_MAX_ACTIVE_RX_URBS; i++) {
1227                 struct sk_buff *skb = dev_alloc_skb(IRDA_SKB_MAX_MTU);
1228                 if (!skb) {
1229                         /* If this ever happen, we are in deep s***.
1230                          * Basically, we can't start the Rx path... */
1231                         IRDA_WARNING("%s(), Failed to allocate Rx skb\n",
1232                                      __func__);
1233                         return -1;
1234                 }
1235                 //skb_reserve(newskb, USB_IRDA_HEADER - 1);
1236                 irda_usb_submit(self, skb, self->rx_urb[i]);
1237         }
1238
1239         /* Ready to play !!! */
1240         return 0;
1241 }
1242
1243 /*------------------------------------------------------------------*/
1244 /*
1245  * Function irda_usb_net_close (self)
1246  *
1247  *    Network device is taken down. Usually this is done by
1248  *    "ifconfig irda0 down"
1249  */
1250 static int irda_usb_net_close(struct net_device *netdev)
1251 {
1252         struct irda_usb_cb *self;
1253         int     i;
1254
1255         IRDA_DEBUG(1, "%s()\n", __func__);
1256
1257         IRDA_ASSERT(netdev != NULL, return -1;);
1258         self = netdev_priv(netdev);
1259         IRDA_ASSERT(self != NULL, return -1;);
1260
1261         /* Clear this flag *before* unlinking the urbs and *before*
1262          * stopping the network Tx queue - Jean II */
1263         self->netopen = 0;
1264
1265         /* Stop network Tx queue */
1266         netif_stop_queue(netdev);
1267
1268         /* Kill defered Rx URB */
1269         del_timer(&self->rx_defer_timer);
1270
1271         /* Deallocate all the Rx path buffers (URBs and skb) */
1272         for (i = 0; i < self->max_rx_urb; i++) {
1273                 struct urb *urb = self->rx_urb[i];
1274                 struct sk_buff *skb = (struct sk_buff *) urb->context;
1275                 /* Cancel the receive command */
1276                 usb_kill_urb(urb);
1277                 /* The skb is ours, free it */
1278                 if(skb) {
1279                         dev_kfree_skb(skb);
1280                         urb->context = NULL;
1281                 }
1282         }
1283         /* Cancel Tx and speed URB - need to be synchronous to avoid races */
1284         usb_kill_urb(self->tx_urb);
1285         usb_kill_urb(self->speed_urb);
1286
1287         /* Stop and remove instance of IrLAP */
1288         if (self->irlap)
1289                 irlap_close(self->irlap);
1290         self->irlap = NULL;
1291
1292         return 0;
1293 }
1294
1295 /*------------------------------------------------------------------*/
1296 /*
1297  * IOCTLs : Extra out-of-band network commands...
1298  */
1299 static int irda_usb_net_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
1300 {
1301         unsigned long flags;
1302         struct if_irda_req *irq = (struct if_irda_req *) rq;
1303         struct irda_usb_cb *self;
1304         int ret = 0;
1305
1306         IRDA_ASSERT(dev != NULL, return -1;);
1307         self = netdev_priv(dev);
1308         IRDA_ASSERT(self != NULL, return -1;);
1309
1310         IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __func__, dev->name, cmd);
1311
1312         switch (cmd) {
1313         case SIOCSBANDWIDTH: /* Set bandwidth */
1314                 if (!capable(CAP_NET_ADMIN))
1315                         return -EPERM;
1316                 /* Protect us from USB callbacks, net watchdog and else. */
1317                 spin_lock_irqsave(&self->lock, flags);
1318                 /* Check if the device is still there */
1319                 if(self->present) {
1320                         /* Set the desired speed */
1321                         self->new_speed = irq->ifr_baudrate;
1322                         irda_usb_change_speed_xbofs(self);
1323                 }
1324                 spin_unlock_irqrestore(&self->lock, flags);
1325                 break;
1326         case SIOCSMEDIABUSY: /* Set media busy */
1327                 if (!capable(CAP_NET_ADMIN))
1328                         return -EPERM;
1329                 /* Check if the IrDA stack is still there */
1330                 if(self->netopen)
1331                         irda_device_set_media_busy(self->netdev, TRUE);
1332                 break;
1333         case SIOCGRECEIVING: /* Check if we are receiving right now */
1334                 irq->ifr_receiving = irda_usb_is_receiving(self);
1335                 break;
1336         default:
1337                 ret = -EOPNOTSUPP;
1338         }
1339
1340         return ret;
1341 }
1342
1343 /*------------------------------------------------------------------*/
1344
1345 /********************* IRDA CONFIG SUBROUTINES *********************/
1346 /*
1347  * Various subroutines dealing with IrDA and network stuff we use to
1348  * configure and initialise each irda-usb instance.
1349  * These functions are used below in the main calls of the driver...
1350  */
1351
1352 /*------------------------------------------------------------------*/
1353 /*
1354  * Set proper values in the IrDA QOS structure
1355  */
1356 static inline void irda_usb_init_qos(struct irda_usb_cb *self)
1357 {
1358         struct irda_class_desc *desc;
1359
1360         IRDA_DEBUG(3, "%s()\n", __func__);
1361
1362         desc = self->irda_desc;
1363
1364         /* Initialize QoS for this device */
1365         irda_init_max_qos_capabilies(&self->qos);
1366
1367         /* See spec section 7.2 for meaning.
1368          * Values are little endian (as most USB stuff), the IrDA stack
1369          * use it in native order (see parameters.c). - Jean II */
1370         self->qos.baud_rate.bits       = le16_to_cpu(desc->wBaudRate);
1371         self->qos.min_turn_time.bits   = desc->bmMinTurnaroundTime;
1372         self->qos.additional_bofs.bits = desc->bmAdditionalBOFs;
1373         self->qos.window_size.bits     = desc->bmWindowSize;
1374         self->qos.data_size.bits       = desc->bmDataSize;
1375
1376         IRDA_DEBUG(0, "%s(), dongle says speed=0x%X, size=0x%X, window=0x%X, bofs=0x%X, turn=0x%X\n",
1377                 __func__, self->qos.baud_rate.bits, self->qos.data_size.bits, self->qos.window_size.bits, self->qos.additional_bofs.bits, self->qos.min_turn_time.bits);
1378
1379         /* Don't always trust what the dongle tell us */
1380         if(self->capability & IUC_SIR_ONLY)
1381                 self->qos.baud_rate.bits        &= 0x00ff;
1382         if(self->capability & IUC_SMALL_PKT)
1383                 self->qos.data_size.bits         = 0x07;
1384         if(self->capability & IUC_NO_WINDOW)
1385                 self->qos.window_size.bits       = 0x01;
1386         if(self->capability & IUC_MAX_WINDOW)
1387                 self->qos.window_size.bits       = 0x7f;
1388         if(self->capability & IUC_MAX_XBOFS)
1389                 self->qos.additional_bofs.bits   = 0x01;
1390
1391 #if 1
1392         /* Module parameter can override the rx window size */
1393         if (qos_mtt_bits)
1394                 self->qos.min_turn_time.bits = qos_mtt_bits;
1395 #endif
1396         /*
1397          * Note : most of those values apply only for the receive path,
1398          * the transmit path will be set differently - Jean II
1399          */
1400         irda_qos_bits_to_value(&self->qos);
1401 }
1402
1403 /*------------------------------------------------------------------*/
1404 static const struct net_device_ops irda_usb_netdev_ops = {
1405         .ndo_open       = irda_usb_net_open,
1406         .ndo_stop       = irda_usb_net_close,
1407         .ndo_do_ioctl   = irda_usb_net_ioctl,
1408         .ndo_start_xmit = irda_usb_hard_xmit,
1409         .ndo_tx_timeout = irda_usb_net_timeout,
1410 };
1411
1412 /*
1413  * Initialise the network side of the irda-usb instance
1414  * Called when a new USB instance is registered in irda_usb_probe()
1415  */
1416 static inline int irda_usb_open(struct irda_usb_cb *self)
1417 {
1418         struct net_device *netdev = self->netdev;
1419
1420         IRDA_DEBUG(1, "%s()\n", __func__);
1421
1422         netdev->netdev_ops = &irda_usb_netdev_ops;
1423
1424         irda_usb_init_qos(self);
1425
1426         return register_netdev(netdev);
1427 }
1428
1429 /*------------------------------------------------------------------*/
1430 /*
1431  * Cleanup the network side of the irda-usb instance
1432  * Called when a USB instance is removed in irda_usb_disconnect()
1433  */
1434 static inline void irda_usb_close(struct irda_usb_cb *self)
1435 {
1436         IRDA_DEBUG(1, "%s()\n", __func__);
1437
1438         /* Remove netdevice */
1439         unregister_netdev(self->netdev);
1440
1441         /* Remove the speed buffer */
1442         kfree(self->speed_buff);
1443         self->speed_buff = NULL;
1444
1445         kfree(self->tx_buff);
1446         self->tx_buff = NULL;
1447 }
1448
1449 /********************** USB CONFIG SUBROUTINES **********************/
1450 /*
1451  * Various subroutines dealing with USB stuff we use to configure and
1452  * initialise each irda-usb instance.
1453  * These functions are used below in the main calls of the driver...
1454  */
1455
1456 /*------------------------------------------------------------------*/
1457 /*
1458  * Function irda_usb_parse_endpoints(dev, ifnum)
1459  *
1460  *    Parse the various endpoints and find the one we need.
1461  *
1462  * The endpoint are the pipes used to communicate with the USB device.
1463  * The spec defines 2 endpoints of type bulk transfer, one in, and one out.
1464  * These are used to pass frames back and forth with the dongle.
1465  * Most dongle have also an interrupt endpoint, that will be probably
1466  * documented in the next spec...
1467  */
1468 static inline int irda_usb_parse_endpoints(struct irda_usb_cb *self, struct usb_host_endpoint *endpoint, int ennum)
1469 {
1470         int i;          /* Endpoint index in table */
1471
1472         /* Init : no endpoints */
1473         self->bulk_in_ep = 0;
1474         self->bulk_out_ep = 0;
1475         self->bulk_int_ep = 0;
1476
1477         /* Let's look at all those endpoints */
1478         for(i = 0; i < ennum; i++) {
1479                 /* All those variables will get optimised by the compiler,
1480                  * so let's aim for clarity... - Jean II */
1481                 __u8 ep;        /* Endpoint address */
1482                 __u8 dir;       /* Endpoint direction */
1483                 __u8 attr;      /* Endpoint attribute */
1484                 __u16 psize;    /* Endpoint max packet size in bytes */
1485
1486                 /* Get endpoint address, direction and attribute */
1487                 ep = endpoint[i].desc.bEndpointAddress & USB_ENDPOINT_NUMBER_MASK;
1488                 dir = endpoint[i].desc.bEndpointAddress & USB_ENDPOINT_DIR_MASK;
1489                 attr = endpoint[i].desc.bmAttributes;
1490                 psize = le16_to_cpu(endpoint[i].desc.wMaxPacketSize);
1491
1492                 /* Is it a bulk endpoint ??? */
1493                 if(attr == USB_ENDPOINT_XFER_BULK) {
1494                         /* We need to find an IN and an OUT */
1495                         if(dir == USB_DIR_IN) {
1496                                 /* This is our Rx endpoint */
1497                                 self->bulk_in_ep = ep;
1498                         } else {
1499                                 /* This is our Tx endpoint */
1500                                 self->bulk_out_ep = ep;
1501                                 self->bulk_out_mtu = psize;
1502                         }
1503                 } else {
1504                         if((attr == USB_ENDPOINT_XFER_INT) &&
1505                            (dir == USB_DIR_IN)) {
1506                                 /* This is our interrupt endpoint */
1507                                 self->bulk_int_ep = ep;
1508                         } else {
1509                                 IRDA_ERROR("%s(), Unrecognised endpoint %02X.\n", __func__, ep);
1510                         }
1511                 }
1512         }
1513
1514         IRDA_DEBUG(0, "%s(), And our endpoints are : in=%02X, out=%02X (%d), int=%02X\n",
1515                 __func__, self->bulk_in_ep, self->bulk_out_ep, self->bulk_out_mtu, self->bulk_int_ep);
1516
1517         return((self->bulk_in_ep != 0) && (self->bulk_out_ep != 0));
1518 }
1519
1520 #ifdef IU_DUMP_CLASS_DESC
1521 /*------------------------------------------------------------------*/
1522 /*
1523  * Function usb_irda_dump_class_desc(desc)
1524  *
1525  *    Prints out the contents of the IrDA class descriptor
1526  *
1527  */
1528 static inline void irda_usb_dump_class_desc(struct irda_class_desc *desc)
1529 {
1530         /* Values are little endian */
1531         printk("bLength=%x\n", desc->bLength);
1532         printk("bDescriptorType=%x\n", desc->bDescriptorType);
1533         printk("bcdSpecRevision=%x\n", le16_to_cpu(desc->bcdSpecRevision));
1534         printk("bmDataSize=%x\n", desc->bmDataSize);
1535         printk("bmWindowSize=%x\n", desc->bmWindowSize);
1536         printk("bmMinTurnaroundTime=%d\n", desc->bmMinTurnaroundTime);
1537         printk("wBaudRate=%x\n", le16_to_cpu(desc->wBaudRate));
1538         printk("bmAdditionalBOFs=%x\n", desc->bmAdditionalBOFs);
1539         printk("bIrdaRateSniff=%x\n", desc->bIrdaRateSniff);
1540         printk("bMaxUnicastList=%x\n", desc->bMaxUnicastList);
1541 }
1542 #endif /* IU_DUMP_CLASS_DESC */
1543
1544 /*------------------------------------------------------------------*/
1545 /*
1546  * Function irda_usb_find_class_desc(intf)
1547  *
1548  *    Returns instance of IrDA class descriptor, or NULL if not found
1549  *
1550  * The class descriptor is some extra info that IrDA USB devices will
1551  * offer to us, describing their IrDA characteristics. We will use that in
1552  * irda_usb_init_qos()
1553  */
1554 static inline struct irda_class_desc *irda_usb_find_class_desc(struct usb_interface *intf)
1555 {
1556         struct usb_device *dev = interface_to_usbdev (intf);
1557         struct irda_class_desc *desc;
1558         int ret;
1559
1560         desc = kzalloc(sizeof(*desc), GFP_KERNEL);
1561         if (!desc)
1562                 return NULL;
1563
1564         /* USB-IrDA class spec 1.0:
1565          *      6.1.3: Standard "Get Descriptor" Device Request is not
1566          *             appropriate to retrieve class-specific descriptor
1567          *      6.2.5: Class Specific "Get Class Descriptor" Interface Request
1568          *             is mandatory and returns the USB-IrDA class descriptor
1569          */
1570
1571         ret = usb_control_msg(dev, usb_rcvctrlpipe(dev,0),
1572                 IU_REQ_GET_CLASS_DESC,
1573                 USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE,
1574                 0, intf->altsetting->desc.bInterfaceNumber, desc,
1575                 sizeof(*desc), 500);
1576
1577         IRDA_DEBUG(1, "%s(), ret=%d\n", __func__, ret);
1578         if (ret < sizeof(*desc)) {
1579                 IRDA_WARNING("usb-irda: class_descriptor read %s (%d)\n",
1580                              (ret<0) ? "failed" : "too short", ret);
1581         }
1582         else if (desc->bDescriptorType != USB_DT_IRDA) {
1583                 IRDA_WARNING("usb-irda: bad class_descriptor type\n");
1584         }
1585         else {
1586 #ifdef IU_DUMP_CLASS_DESC
1587                 irda_usb_dump_class_desc(desc);
1588 #endif  /* IU_DUMP_CLASS_DESC */
1589
1590                 return desc;
1591         }
1592         kfree(desc);
1593         return NULL;
1594 }
1595
1596 /*********************** USB DEVICE CALLBACKS ***********************/
1597 /*
1598  * Main calls from the USB subsystem.
1599  * Mostly registering a new irda-usb device and removing it....
1600  */
1601
1602 /*------------------------------------------------------------------*/
1603 /*
1604  * This routine is called by the USB subsystem for each new device
1605  * in the system. We need to check if the device is ours, and in
1606  * this case start handling it.
1607  * The USB layer protect us from reentrancy (via BKL), so we don't need
1608  * to spinlock in there... Jean II
1609  */
1610 static int irda_usb_probe(struct usb_interface *intf,
1611                           const struct usb_device_id *id)
1612 {
1613         struct net_device *net;
1614         struct usb_device *dev = interface_to_usbdev(intf);
1615         struct irda_usb_cb *self;
1616         struct usb_host_interface *interface;
1617         struct irda_class_desc *irda_desc;
1618         int ret = -ENOMEM;
1619         int i;          /* Driver instance index / Rx URB index */
1620
1621         /* Note : the probe make sure to call us only for devices that
1622          * matches the list of dongle (top of the file). So, we
1623          * don't need to check if the dongle is really ours.
1624          * Jean II */
1625
1626         IRDA_MESSAGE("IRDA-USB found at address %d, Vendor: %x, Product: %x\n",
1627                      dev->devnum, le16_to_cpu(dev->descriptor.idVendor),
1628                      le16_to_cpu(dev->descriptor.idProduct));
1629
1630         net = alloc_irdadev(sizeof(*self));
1631         if (!net)
1632                 goto err_out;
1633
1634         SET_NETDEV_DEV(net, &intf->dev);
1635         self = netdev_priv(net);
1636         self->netdev = net;
1637         spin_lock_init(&self->lock);
1638         init_timer(&self->rx_defer_timer);
1639
1640         self->capability = id->driver_info;
1641         self->needspatch = ((self->capability & IUC_STIR421X) != 0);
1642
1643         /* Create all of the needed urbs */
1644         if (self->capability & IUC_STIR421X) {
1645                 self->max_rx_urb = IU_SIGMATEL_MAX_RX_URBS;
1646                 self->header_length = USB_IRDA_STIR421X_HEADER;
1647         } else {
1648                 self->max_rx_urb = IU_MAX_RX_URBS;
1649                 self->header_length = USB_IRDA_HEADER;
1650         }
1651
1652         self->rx_urb = kcalloc(self->max_rx_urb, sizeof(struct urb *),
1653                                 GFP_KERNEL);
1654
1655         for (i = 0; i < self->max_rx_urb; i++) {
1656                 self->rx_urb[i] = usb_alloc_urb(0, GFP_KERNEL);
1657                 if (!self->rx_urb[i]) {
1658                         goto err_out_1;
1659                 }
1660         }
1661         self->tx_urb = usb_alloc_urb(0, GFP_KERNEL);
1662         if (!self->tx_urb) {
1663                 goto err_out_1;
1664         }
1665         self->speed_urb = usb_alloc_urb(0, GFP_KERNEL);
1666         if (!self->speed_urb) {
1667                 goto err_out_2;
1668         }
1669
1670         /* Is this really necessary? (no, except maybe for broken devices) */
1671         if (usb_reset_configuration (dev) < 0) {
1672                 err("reset_configuration failed");
1673                 ret = -EIO;
1674                 goto err_out_3;
1675         }
1676
1677         /* Is this really necessary? */
1678         /* Note : some driver do hardcode the interface number, some others
1679          * specify an alternate, but very few driver do like this.
1680          * Jean II */
1681         ret = usb_set_interface(dev, intf->altsetting->desc.bInterfaceNumber, 0);
1682         IRDA_DEBUG(1, "usb-irda: set interface %d result %d\n", intf->altsetting->desc.bInterfaceNumber, ret);
1683         switch (ret) {
1684                 case 0:
1685                         break;
1686                 case -EPIPE:            /* -EPIPE = -32 */
1687                         /* Martin Diehl says if we get a -EPIPE we should
1688                          * be fine and we don't need to do a usb_clear_halt().
1689                          * - Jean II */
1690                         IRDA_DEBUG(0, "%s(), Received -EPIPE, ignoring...\n", __func__);
1691                         break;
1692                 default:
1693                         IRDA_DEBUG(0, "%s(), Unknown error %d\n", __func__, ret);
1694                         ret = -EIO;
1695                         goto err_out_3;
1696         }
1697
1698         /* Find our endpoints */
1699         interface = intf->cur_altsetting;
1700         if(!irda_usb_parse_endpoints(self, interface->endpoint,
1701                                      interface->desc.bNumEndpoints)) {
1702                 IRDA_ERROR("%s(), Bogus endpoints...\n", __func__);
1703                 ret = -EIO;
1704                 goto err_out_3;
1705         }
1706
1707         self->usbdev = dev;
1708
1709         /* Find IrDA class descriptor */
1710         irda_desc = irda_usb_find_class_desc(intf);
1711         ret = -ENODEV;
1712         if (!irda_desc)
1713                 goto err_out_3;
1714
1715         if (self->needspatch) {
1716                 ret = usb_control_msg (self->usbdev, usb_sndctrlpipe (self->usbdev, 0),
1717                                        0x02, 0x40, 0, 0, NULL, 0, 500);
1718                 if (ret < 0) {
1719                         IRDA_DEBUG (0, "usb_control_msg failed %d\n", ret);
1720                         goto err_out_3;
1721                 } else {
1722                         mdelay(10);
1723                 }
1724         }
1725
1726         self->irda_desc =  irda_desc;
1727         self->present = 1;
1728         self->netopen = 0;
1729         self->usbintf = intf;
1730
1731         /* Allocate the buffer for speed changes */
1732         /* Don't change this buffer size and allocation without doing
1733          * some heavy and complete testing. Don't ask why :-(
1734          * Jean II */
1735         self->speed_buff = kzalloc(IRDA_USB_SPEED_MTU, GFP_KERNEL);
1736         if (!self->speed_buff)
1737                 goto err_out_3;
1738
1739         self->tx_buff = kzalloc(IRDA_SKB_MAX_MTU + self->header_length,
1740                                 GFP_KERNEL);
1741         if (!self->tx_buff)
1742                 goto err_out_4;
1743
1744         ret = irda_usb_open(self);
1745         if (ret)
1746                 goto err_out_5;
1747
1748         IRDA_MESSAGE("IrDA: Registered device %s\n", net->name);
1749         usb_set_intfdata(intf, self);
1750
1751         if (self->needspatch) {
1752                 /* Now we fetch and upload the firmware patch */
1753                 ret = stir421x_patch_device(self);
1754                 self->needspatch = (ret < 0);
1755                 if (self->needspatch) {
1756                         IRDA_ERROR("STIR421X: Couldn't upload patch\n");
1757                         goto err_out_6;
1758                 }
1759
1760                 /* replace IrDA class descriptor with what patched device is now reporting */
1761                 irda_desc = irda_usb_find_class_desc (self->usbintf);
1762                 if (!irda_desc) {
1763                         ret = -ENODEV;
1764                         goto err_out_6;
1765                 }
1766                 kfree(self->irda_desc);
1767                 self->irda_desc = irda_desc;
1768                 irda_usb_init_qos(self);
1769         }
1770
1771         return 0;
1772 err_out_6:
1773         unregister_netdev(self->netdev);
1774 err_out_5:
1775         kfree(self->tx_buff);
1776 err_out_4:
1777         kfree(self->speed_buff);
1778 err_out_3:
1779         /* Free all urbs that we may have created */
1780         usb_free_urb(self->speed_urb);
1781 err_out_2:
1782         usb_free_urb(self->tx_urb);
1783 err_out_1:
1784         for (i = 0; i < self->max_rx_urb; i++)
1785                 usb_free_urb(self->rx_urb[i]);
1786         free_netdev(net);
1787 err_out:
1788         return ret;
1789 }
1790
1791 /*------------------------------------------------------------------*/
1792 /*
1793  * The current irda-usb device is removed, the USB layer tell us
1794  * to shut it down...
1795  * One of the constraints is that when we exit this function,
1796  * we cannot use the usb_device no more. Gone. Destroyed. kfree().
1797  * Most other subsystem allow you to destroy the instance at a time
1798  * when it's convenient to you, to postpone it to a later date, but
1799  * not the USB subsystem.
1800  * So, we must make bloody sure that everything gets deactivated.
1801  * Jean II
1802  */
1803 static void irda_usb_disconnect(struct usb_interface *intf)
1804 {
1805         unsigned long flags;
1806         struct irda_usb_cb *self = usb_get_intfdata(intf);
1807         int i;
1808
1809         IRDA_DEBUG(1, "%s()\n", __func__);
1810
1811         usb_set_intfdata(intf, NULL);
1812         if (!self)
1813                 return;
1814
1815         /* Make sure that the Tx path is not executing. - Jean II */
1816         spin_lock_irqsave(&self->lock, flags);
1817
1818         /* Oups ! We are not there any more.
1819          * This will stop/desactivate the Tx path. - Jean II */
1820         self->present = 0;
1821
1822         /* Kill defered Rx URB */
1823         del_timer(&self->rx_defer_timer);
1824
1825         /* We need to have irq enabled to unlink the URBs. That's OK,
1826          * at this point the Tx path is gone - Jean II */
1827         spin_unlock_irqrestore(&self->lock, flags);
1828
1829         /* Hum... Check if networking is still active (avoid races) */
1830         if((self->netopen) || (self->irlap)) {
1831                 /* Accept no more transmissions */
1832                 /*netif_device_detach(self->netdev);*/
1833                 netif_stop_queue(self->netdev);
1834                 /* Stop all the receive URBs. Must be synchronous. */
1835                 for (i = 0; i < self->max_rx_urb; i++)
1836                         usb_kill_urb(self->rx_urb[i]);
1837                 /* Cancel Tx and speed URB.
1838                  * Make sure it's synchronous to avoid races. */
1839                 usb_kill_urb(self->tx_urb);
1840                 usb_kill_urb(self->speed_urb);
1841         }
1842
1843         /* Cleanup the device stuff */
1844         irda_usb_close(self);
1845         /* No longer attached to USB bus */
1846         self->usbdev = NULL;
1847         self->usbintf = NULL;
1848
1849         /* Clean up our urbs */
1850         for (i = 0; i < self->max_rx_urb; i++)
1851                 usb_free_urb(self->rx_urb[i]);
1852         kfree(self->rx_urb);
1853         /* Clean up Tx and speed URB */
1854         usb_free_urb(self->tx_urb);
1855         usb_free_urb(self->speed_urb);
1856
1857         /* Free self and network device */
1858         free_netdev(self->netdev);
1859         IRDA_DEBUG(0, "%s(), USB IrDA Disconnected\n", __func__);
1860 }
1861
1862 #ifdef CONFIG_PM
1863 /* USB suspend, so power off the transmitter/receiver */
1864 static int irda_usb_suspend(struct usb_interface *intf, pm_message_t message)
1865 {
1866         struct irda_usb_cb *self = usb_get_intfdata(intf);
1867         int i;
1868
1869         netif_device_detach(self->netdev);
1870
1871         if (self->tx_urb != NULL)
1872                 usb_kill_urb(self->tx_urb);
1873         if (self->speed_urb != NULL)
1874                 usb_kill_urb(self->speed_urb);
1875         for (i = 0; i < self->max_rx_urb; i++) {
1876                 if (self->rx_urb[i] != NULL)
1877                         usb_kill_urb(self->rx_urb[i]);
1878         }
1879         return 0;
1880 }
1881
1882 /* Coming out of suspend, so reset hardware */
1883 static int irda_usb_resume(struct usb_interface *intf)
1884 {
1885         struct irda_usb_cb *self = usb_get_intfdata(intf);
1886         int i;
1887
1888         for (i = 0; i < self->max_rx_urb; i++) {
1889                 if (self->rx_urb[i] != NULL)
1890                         usb_submit_urb(self->rx_urb[i], GFP_KERNEL);
1891         }
1892
1893         netif_device_attach(self->netdev);
1894         return 0;
1895 }
1896 #endif
1897
1898 /*------------------------------------------------------------------*/
1899 /*
1900  * USB device callbacks
1901  */
1902 static struct usb_driver irda_driver = {
1903         .name           = "irda-usb",
1904         .probe          = irda_usb_probe,
1905         .disconnect     = irda_usb_disconnect,
1906         .id_table       = dongles,
1907 #ifdef CONFIG_PM
1908         .suspend        = irda_usb_suspend,
1909         .resume         = irda_usb_resume,
1910 #endif
1911 };
1912
1913 /************************* MODULE CALLBACKS *************************/
1914 /*
1915  * Deal with module insertion/removal
1916  * Mostly tell USB about our existence
1917  */
1918
1919 /*------------------------------------------------------------------*/
1920 /*
1921  * Module insertion
1922  */
1923 static int __init usb_irda_init(void)
1924 {
1925         int     ret;
1926
1927         ret = usb_register(&irda_driver);
1928         if (ret < 0)
1929                 return ret;
1930
1931         IRDA_MESSAGE("USB IrDA support registered\n");
1932         return 0;
1933 }
1934 module_init(usb_irda_init);
1935
1936 /*------------------------------------------------------------------*/
1937 /*
1938  * Module removal
1939  */
1940 static void __exit usb_irda_cleanup(void)
1941 {
1942         /* Deregister the driver and remove all pending instances */
1943         usb_deregister(&irda_driver);
1944 }
1945 module_exit(usb_irda_cleanup);
1946
1947 /*------------------------------------------------------------------*/
1948 /*
1949  * Module parameters
1950  */
1951 module_param(qos_mtt_bits, int, 0);
1952 MODULE_PARM_DESC(qos_mtt_bits, "Minimum Turn Time");
1953 MODULE_AUTHOR("Roman Weissgaerber <weissg@vienna.at>, Dag Brattli <dag@brattli.net>, Jean Tourrilhes <jt@hpl.hp.com> and Nick Fedchik <nick@fedchik.org.ua>");
1954 MODULE_DESCRIPTION("IrDA-USB Dongle Driver");
1955 MODULE_LICENSE("GPL");