drivers/pcmcia/o2micro.h

   1 /*
   2  * o2micro.h 1.13 1999/10/25 20:03:34
   3  *
   4  * The contents of this file are subject to the Mozilla Public License
   5  * Version 1.1 (the "License"); you may not use this file except in
   6  * compliance with the License. You may obtain a copy of the License
   7  * at http://www.mozilla.org/MPL/
   8  *
   9  * Software distributed under the License is distributed on an "AS IS"
  10  * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
  11  * the License for the specific language governing rights and
  12  * limitations under the License.
  13  *
  14  * The initial developer of the original code is David A. Hinds
  15  * <dahinds@users.sourceforge.net>.  Portions created by David A. Hinds
  16  * are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
  17  *
  18  * Alternatively, the contents of this file may be used under the
  19  * terms of the GNU General Public License version 2 (the "GPL"), in which
  20  * case the provisions of the GPL are applicable instead of the
  21  * above.  If you wish to allow the use of your version of this file
  22  * only under the terms of the GPL and not to allow others to use
  23  * your version of this file under the MPL, indicate your decision by
  24  * deleting the provisions above and replace them with the notice and
  25  * other provisions required by the GPL.  If you do not delete the
  26  * provisions above, a recipient may use your version of this file
  27  * under either the MPL or the GPL.
  28  */
  29
  30 #ifndef _LINUX_O2MICRO_H
  31 #define _LINUX_O2MICRO_H
  32
  33 #ifndef PCI_VENDOR_ID_O2
  34 #define PCI_VENDOR_ID_O2                0x1217
  35 #endif
  36 #ifndef PCI_DEVICE_ID_O2_6729
  37 #define PCI_DEVICE_ID_O2_6729           0x6729
  38 #endif
  39 #ifndef PCI_DEVICE_ID_O2_6730
  40 #define PCI_DEVICE_ID_O2_6730           0x673a
  41 #endif
  42 #ifndef PCI_DEVICE_ID_O2_6832
  43 #define PCI_DEVICE_ID_O2_6832           0x6832
  44 #endif
  45 #ifndef PCI_DEVICE_ID_O2_6836
  46 #define PCI_DEVICE_ID_O2_6836           0x6836
  47 #endif
  48 #ifndef PCI_DEVICE_ID_O2_6812
  49 #define PCI_DEVICE_ID_O2_6812           0x6872
  50 #endif
  51 #ifndef PCI_DEVICE_ID_O2_6933
  52 #define PCI_DEVICE_ID_O2_6933           0x6933
  53 #endif
  54
  55 /* Additional PCI configuration registers */
  56
  57 #define O2_MUX_CONTROL          0x90    /* 32 bit */
  58 #define  O2_MUX_RING_OUT        0x0000000f
  59 #define  O2_MUX_SKTB_ACTV       0x000000f0
  60 #define  O2_MUX_SCTA_ACTV_ENA   0x00000100
  61 #define  O2_MUX_SCTB_ACTV_ENA   0x00000200
  62 #define  O2_MUX_SER_IRQ_ROUTE   0x0000e000
  63 #define  O2_MUX_SER_PCI         0x00010000
  64
  65 #define  O2_MUX_SKTA_TURBO      0x000c0000      /* for 6833, 6860 */
  66 #define  O2_MUX_SKTB_TURBO      0x00300000
  67 #define  O2_MUX_AUX_VCC_3V      0x00400000
  68 #define  O2_MUX_PCI_VCC_5V      0x00800000
  69 #define  O2_MUX_PME_MUX         0x0f000000
  70
  71 /* Additional ExCA registers */
  72
  73 #define O2_MODE_A               0x38
  74 #define O2_MODE_A_2             0x26    /* for 6833B, 6860C */
  75 #define  O2_MODE_A_CD_PULSE     0x04
  76 #define  O2_MODE_A_SUSP_EDGE    0x08
  77 #define  O2_MODE_A_HOST_SUSP    0x10
  78 #define  O2_MODE_A_PWR_MASK     0x60
  79 #define  O2_MODE_A_QUIET        0x80
  80
  81 #define O2_MODE_B               0x39
  82 #define O2_MODE_B_2             0x2e    /* for 6833B, 6860C */
  83 #define  O2_MODE_B_IDENT        0x03
  84 #define  O2_MODE_B_ID_BSTEP     0x00
  85 #define  O2_MODE_B_ID_CSTEP     0x01
  86 #define  O2_MODE_B_ID_O2        0x02
  87 #define  O2_MODE_B_VS1          0x04
  88 #define  O2_MODE_B_VS2          0x08
  89 #define  O2_MODE_B_IRQ15_RI     0x80
  90
  91 #define O2_MODE_C               0x3a
  92 #define  O2_MODE_C_DREQ_MASK    0x03
  93 #define  O2_MODE_C_DREQ_INPACK  0x01
  94 #define  O2_MODE_C_DREQ_WP      0x02
  95 #define  O2_MODE_C_DREQ_BVD2    0x03
  96 #define  O2_MODE_C_ZVIDEO       0x08
  97 #define  O2_MODE_C_IREQ_SEL     0x30
  98 #define  O2_MODE_C_MGMT_SEL     0xc0
  99
 100 #define O2_MODE_D               0x3b
 101 #define  O2_MODE_D_IRQ_MODE     0x03
 102 #define  O2_MODE_D_PCI_CLKRUN   0x04
 103 #define  O2_MODE_D_CB_CLKRUN    0x08
 104 #define  O2_MODE_D_SKT_ACTV     0x20
 105 #define  O2_MODE_D_PCI_FIFO     0x40    /* for OZ6729, OZ6730 */
 106 #define  O2_MODE_D_W97_IRQ      0x40
 107 #define  O2_MODE_D_ISA_IRQ      0x80
 108
 109 #define O2_MHPG_DMA             0x3c
 110 #define  O2_MHPG_CHANNEL        0x07
 111 #define  O2_MHPG_CINT_ENA       0x08
 112 #define  O2_MHPG_CSC_ENA        0x10
 113
 114 #define O2_FIFO_ENA             0x3d
 115 #define  O2_FIFO_ZVIDEO_3       0x08
 116 #define  O2_FIFO_PCI_FIFO       0x10
 117 #define  O2_FIFO_POSTWR         0x40
 118 #define  O2_FIFO_BUFFER         0x80
 119
 120 #define O2_MODE_E               0x3e
 121 #define  O2_MODE_E_MHPG_DMA     0x01
 122 #define  O2_MODE_E_SPKR_OUT     0x02
 123 #define  O2_MODE_E_LED_OUT      0x08
 124 #define  O2_MODE_E_SKTA_ACTV    0x10
 125
 126 #define O2_RESERVED1            0x94
 127 #define O2_RESERVED2            0xD4
 128 #define O2_RES_READ_PREFETCH    0x02
 129 #define O2_RES_WRITE_BURST      0x08
 130
 131 static int o2micro_override(struct yenta_socket *socket)
 132 {
 133         /*
 134          * 'reserved' register at 0x94/D4. allows setting read prefetch and write
 135          * bursting. read prefetching for example makes the RME Hammerfall DSP
 136          * working. for some bridges it is at 0x94, for others at 0xD4. it's
 137          * ok to write to both registers on all O2 bridges.
 138          * from Eric Still, 02Micro.
 139          */
 140         u8 a, b;
 141
 142         if (PCI_FUNC(socket->dev->devfn) == 0) {
 143                 a = config_readb(socket, O2_RESERVED1);
 144                 b = config_readb(socket, O2_RESERVED2);
 145
 146                 dev_printk(KERN_INFO, &socket->dev->dev,
 147                            "O2: res at 0x94/0xD4: %02x/%02x\n", a, b);
 148
 149                 switch (socket->dev->device) {
 150                 /*
 151                  * older bridges have problems with both read prefetch and write
 152                  * bursting depending on the combination of the chipset, bridge
 153                  * and the cardbus card. so disable them to be on the safe side.
 154                  */
 155                 case PCI_DEVICE_ID_O2_6729:
 156                 case PCI_DEVICE_ID_O2_6730:
 157                 case PCI_DEVICE_ID_O2_6812:
 158                 case PCI_DEVICE_ID_O2_6832:
 159                 case PCI_DEVICE_ID_O2_6836:
 160                 case PCI_DEVICE_ID_O2_6933:
 161                         dev_printk(KERN_INFO, &socket->dev->dev,
 162                                    "Yenta O2: old bridge, disabling read "
 163                                    "prefetch/write burst\n");
 164                         config_writeb(socket, O2_RESERVED1,
 165                                       a & ~(O2_RES_READ_PREFETCH | O2_RES_WRITE_BURST));
 166                         config_writeb(socket, O2_RESERVED2,
 167                                       b & ~(O2_RES_READ_PREFETCH | O2_RES_WRITE_BURST));
 168                         break;
 169
 170                 default:
 171                         dev_printk(KERN_INFO , &socket->dev->dev,
 172                                    "O2: enabling read prefetch/write burst\n");
 173                         config_writeb(socket, O2_RESERVED1,
 174                                       a | O2_RES_READ_PREFETCH | O2_RES_WRITE_BURST);
 175                         config_writeb(socket, O2_RESERVED2,
 176                                       b | O2_RES_READ_PREFETCH | O2_RES_WRITE_BURST);
 177                 }
 178         }
 179
 180         return 0;
 181 }
 182
 183 static void o2micro_restore_state(struct yenta_socket *socket)
 184 {
 185         /*
 186          * as long as read prefetch is the only thing in
 187          * o2micro_override, it's safe to call it from here
 188          */
 189         o2micro_override(socket);
 190 }
 191
 192 #endif /* _LINUX_O2MICRO_H */