drivers/mtd/devices/lart.c

   1
   2 /*
   3  * MTD driver for the 28F160F3 Flash Memory (non-CFI) on LART.
   4  *
   5  * $Id: lart.c,v 1.9 2005/11/07 11:14:25 gleixner Exp $
   6  *
   7  * Author: Abraham vd Merwe <abraham@2d3d.co.za>
   8  *
   9  * Copyright (c) 2001, 2d3D, Inc.
  10  *
  11  * This code is free software; you can redistribute it and/or modify
  12  * it under the terms of the GNU General Public License version 2 as
  13  * published by the Free Software Foundation.
  14  *
  15  * References:
  16  *
  17  *    [1] 3 Volt Fast Boot Block Flash Memory" Intel Datasheet
  18  *           - Order Number: 290644-005
  19  *           - January 2000
  20  *
  21  *    [2] MTD internal API documentation
  22  *           - http://www.linux-mtd.infradead.org/tech/
  23  *
  24  * Limitations:
  25  *
  26  *    Even though this driver is written for 3 Volt Fast Boot
  27  *    Block Flash Memory, it is rather specific to LART. With
  28  *    Minor modifications, notably the without data/address line
  29  *    mangling and different bus settings, etc. it should be
  30  *    trivial to adapt to other platforms.
  31  *
  32  *    If somebody would sponsor me a different board, I'll
  33  *    adapt the driver (:
  34  */
  35
  36 /* debugging */
  37 //#define LART_DEBUG
  38
  39 /* partition support */
  40 #define HAVE_PARTITIONS
  41
  42 #include <linux/kernel.h>
  43 #include <linux/module.h>
  44 #include <linux/types.h>
  45 #include <linux/init.h>
  46 #include <linux/errno.h>
  47 #include <linux/string.h>
  48 #include <linux/mtd/mtd.h>
  49 #ifdef HAVE_PARTITIONS
  50 #include <linux/mtd/partitions.h>
  51 #endif
  52
  53 #ifndef CONFIG_SA1100_LART
  54 #error This is for LART architecture only
  55 #endif
  56
  57 static char module_name[] = "lart";
  58
  59 /*
  60  * These values is specific to 28Fxxxx3 flash memory.
  61  * See section 2.3.1 in "3 Volt Fast Boot Block Flash Memory" Intel Datasheet
  62  */
  63 #define FLASH_BLOCKSIZE_PARAM           (4096 * BUSWIDTH)
  64 #define FLASH_NUMBLOCKS_16m_PARAM       8
  65 #define FLASH_NUMBLOCKS_8m_PARAM        8
  66
  67 /*
  68  * These values is specific to 28Fxxxx3 flash memory.
  69  * See section 2.3.2 in "3 Volt Fast Boot Block Flash Memory" Intel Datasheet
  70  */
  71 #define FLASH_BLOCKSIZE_MAIN            (32768 * BUSWIDTH)
  72 #define FLASH_NUMBLOCKS_16m_MAIN        31
  73 #define FLASH_NUMBLOCKS_8m_MAIN         15
  74
  75 /*
  76  * These values are specific to LART
  77  */
  78
  79 /* general */
  80 #define BUSWIDTH                        4                               /* don't change this - a lot of the code _will_ break if you change this */
  81 #define FLASH_OFFSET            0xe8000000              /* see linux/arch/arm/mach-sa1100/lart.c */
  82
  83 /* blob */
  84 #define NUM_BLOB_BLOCKS         FLASH_NUMBLOCKS_16m_PARAM
  85 #define BLOB_START                      0x00000000
  86 #define BLOB_LEN                        (NUM_BLOB_BLOCKS * FLASH_BLOCKSIZE_PARAM)
  87
  88 /* kernel */
  89 #define NUM_KERNEL_BLOCKS       7
  90 #define KERNEL_START            (BLOB_START + BLOB_LEN)
  91 #define KERNEL_LEN                      (NUM_KERNEL_BLOCKS * FLASH_BLOCKSIZE_MAIN)
  92
  93 /* initial ramdisk */
  94 #define NUM_INITRD_BLOCKS       24
  95 #define INITRD_START            (KERNEL_START + KERNEL_LEN)
  96 #define INITRD_LEN                      (NUM_INITRD_BLOCKS * FLASH_BLOCKSIZE_MAIN)
  97
  98 /*
  99  * See section 4.0 in "3 Volt Fast Boot Block Flash Memory" Intel Datasheet
 100  */
 101 #define READ_ARRAY                      0x00FF00FF              /* Read Array/Reset */
 102 #define READ_ID_CODES           0x00900090              /* Read Identifier Codes */
 103 #define ERASE_SETUP                     0x00200020              /* Block Erase */
 104 #define ERASE_CONFIRM           0x00D000D0              /* Block Erase and Program Resume */
 105 #define PGM_SETUP                       0x00400040              /* Program */
 106 #define STATUS_READ                     0x00700070              /* Read Status Register */
 107 #define STATUS_CLEAR            0x00500050              /* Clear Status Register */
 108 #define STATUS_BUSY                     0x00800080              /* Write State Machine Status (WSMS) */
 109 #define STATUS_ERASE_ERR        0x00200020              /* Erase Status (ES) */
 110 #define STATUS_PGM_ERR          0x00100010              /* Program Status (PS) */
 111
 112 /*
 113  * See section 4.2 in "3 Volt Fast Boot Block Flash Memory" Intel Datasheet
 114  */
 115 #define FLASH_MANUFACTURER                      0x00890089
 116 #define FLASH_DEVICE_8mbit_TOP          0x88f188f1
 117 #define FLASH_DEVICE_8mbit_BOTTOM       0x88f288f2
 118 #define FLASH_DEVICE_16mbit_TOP         0x88f388f3
 119 #define FLASH_DEVICE_16mbit_BOTTOM      0x88f488f4
 120
 121 /***************************************************************************************************/
 122
 123 /*
 124  * The data line mapping on LART is as follows:
 125  *
 126  *       U2  CPU |   U3  CPU
 127  *       -------------------
 128  *        0  20  |   0   12
 129  *        1  22  |   1   14
 130  *        2  19  |   2   11
 131  *        3  17  |   3   9
 132  *        4  24  |   4   0
 133  *        5  26  |   5   2
 134  *        6  31  |   6   7
 135  *        7  29  |   7   5
 136  *        8  21  |   8   13
 137  *        9  23  |   9   15
 138  *        10 18  |   10  10
 139  *        11 16  |   11  8
 140  *        12 25  |   12  1
 141  *        13 27  |   13  3
 142  *        14 30  |   14  6
 143  *        15 28  |   15  4
 144  */
 145
 146 /* Mangle data (x) */
 147 #define DATA_TO_FLASH(x)                                \
 148         (                                                                       \
 149                 (((x) & 0x08009000) >> 11)      +       \
 150                 (((x) & 0x00002000) >> 10)      +       \
 151                 (((x) & 0x04004000) >> 8)       +       \
 152                 (((x) & 0x00000010) >> 4)       +       \
 153                 (((x) & 0x91000820) >> 3)       +       \
 154                 (((x) & 0x22080080) >> 2)       +       \
 155                 ((x) & 0x40000400)                      +       \
 156                 (((x) & 0x00040040) << 1)       +       \
 157                 (((x) & 0x00110000) << 4)       +       \
 158                 (((x) & 0x00220100) << 5)       +       \
 159                 (((x) & 0x00800208) << 6)       +       \
 160                 (((x) & 0x00400004) << 9)       +       \
 161                 (((x) & 0x00000001) << 12)      +       \
 162                 (((x) & 0x00000002) << 13)              \
 163         )
 164
 165 /* Unmangle data (x) */
 166 #define FLASH_TO_DATA(x)                                \
 167         (                                                                       \
 168                 (((x) & 0x00010012) << 11)      +       \
 169                 (((x) & 0x00000008) << 10)      +       \
 170                 (((x) & 0x00040040) << 8)       +       \
 171                 (((x) & 0x00000001) << 4)       +       \
 172                 (((x) & 0x12200104) << 3)       +       \
 173                 (((x) & 0x08820020) << 2)       +       \
 174                 ((x) & 0x40000400)                      +       \
 175                 (((x) & 0x00080080) >> 1)       +       \
 176                 (((x) & 0x01100000) >> 4)       +       \
 177                 (((x) & 0x04402000) >> 5)       +       \
 178                 (((x) & 0x20008200) >> 6)       +       \
 179                 (((x) & 0x80000800) >> 9)       +       \
 180                 (((x) & 0x00001000) >> 12)      +       \
 181                 (((x) & 0x00004000) >> 13)              \
 182         )
 183
 184 /*
 185  * The address line mapping on LART is as follows:
 186  *
 187  *       U3  CPU |   U2  CPU
 188  *       -------------------
 189  *        0  2   |   0   2
 190  *        1  3   |   1   3
 191  *        2  9   |   2   9
 192  *        3  13  |   3   8
 193  *        4  8   |   4   7
 194  *        5  12  |   5   6
 195  *        6  11  |   6   5
 196  *        7  10  |   7   4
 197  *        8  4   |   8   10
 198  *        9  5   |   9   11
 199  *       10  6   |   10  12
 200  *       11  7   |   11  13
 201  *
 202  *       BOOT BLOCK BOUNDARY
 203  *
 204  *       12  15  |   12  15
 205  *       13  14  |   13  14
 206  *       14  16  |   14  16
 207  *
 208  *       MAIN BLOCK BOUNDARY
 209  *
 210  *       15  17  |   15  18
 211  *       16  18  |   16  17
 212  *       17  20  |   17  20
 213  *       18  19  |   18  19
 214  *       19  21  |   19  21
 215  *
 216  * As we can see from above, the addresses aren't mangled across
 217  * block boundaries, so we don't need to worry about address
 218  * translations except for sending/reading commands during
 219  * initialization
 220  */
 221
 222 /* Mangle address (x) on chip U2 */
 223 #define ADDR_TO_FLASH_U2(x)                             \
 224         (                                                                       \
 225                 (((x) & 0x00000f00) >> 4)       +       \
 226                 (((x) & 0x00042000) << 1)       +       \
 227                 (((x) & 0x0009c003) << 2)       +       \
 228                 (((x) & 0x00021080) << 3)       +       \
 229                 (((x) & 0x00000010) << 4)       +       \
 230                 (((x) & 0x00000040) << 5)       +       \
 231                 (((x) & 0x00000024) << 7)       +       \
 232                 (((x) & 0x00000008) << 10)              \
 233         )
 234
 235 /* Unmangle address (x) on chip U2 */
 236 #define FLASH_U2_TO_ADDR(x)                             \
 237         (                                                                       \
 238                 (((x) << 4) & 0x00000f00)       +       \
 239                 (((x) >> 1) & 0x00042000)       +       \
 240                 (((x) >> 2) & 0x0009c003)       +       \
 241                 (((x) >> 3) & 0x00021080)       +       \
 242                 (((x) >> 4) & 0x00000010)       +       \
 243                 (((x) >> 5) & 0x00000040)       +       \
 244                 (((x) >> 7) & 0x00000024)       +       \
 245                 (((x) >> 10) & 0x00000008)              \
 246         )
 247
 248 /* Mangle address (x) on chip U3 */
 249 #define ADDR_TO_FLASH_U3(x)                             \
 250         (                                                                       \
 251                 (((x) & 0x00000080) >> 3)       +       \
 252                 (((x) & 0x00000040) >> 1)       +       \
 253                 (((x) & 0x00052020) << 1)       +       \
 254                 (((x) & 0x00084f03) << 2)       +       \
 255                 (((x) & 0x00029010) << 3)       +       \
 256                 (((x) & 0x00000008) << 5)       +       \
 257                 (((x) & 0x00000004) << 7)               \
 258         )
 259
 260 /* Unmangle address (x) on chip U3 */
 261 #define FLASH_U3_TO_ADDR(x)                             \
 262         (                                                                       \
 263                 (((x) << 3) & 0x00000080)       +       \
 264                 (((x) << 1) & 0x00000040)       +       \
 265                 (((x) >> 1) & 0x00052020)       +       \
 266                 (((x) >> 2) & 0x00084f03)       +       \
 267                 (((x) >> 3) & 0x00029010)       +       \
 268                 (((x) >> 5) & 0x00000008)       +       \
 269                 (((x) >> 7) & 0x00000004)               \
 270         )
 271
 272 /***************************************************************************************************/
 273
 274 static __u8 read8 (__u32 offset)
 275 {
 276    volatile __u8 *data = (__u8 *) (FLASH_OFFSET + offset);
 277 #ifdef LART_DEBUG
 278    printk (KERN_DEBUG "%s(): 0x%.8x -> 0x%.2x\n",__FUNCTION__,offset,*data);
 279 #endif
 280    return (*data);
 281 }
 282
 283 static __u32 read32 (__u32 offset)
 284 {
 285    volatile __u32 *data = (__u32 *) (FLASH_OFFSET + offset);
 286 #ifdef LART_DEBUG
 287    printk (KERN_DEBUG "%s(): 0x%.8x -> 0x%.8x\n",__FUNCTION__,offset,*data);
 288 #endif
 289    return (*data);
 290 }
 291
 292 static void write32 (__u32 x,__u32 offset)
 293 {
 294    volatile __u32 *data = (__u32 *) (FLASH_OFFSET + offset);
 295    *data = x;
 296 #ifdef LART_DEBUG
 297    printk (KERN_DEBUG "%s(): 0x%.8x <- 0x%.8x\n",__FUNCTION__,offset,*data);
 298 #endif
 299 }
 300
 301 /***************************************************************************************************/
 302
 303 /*
 304  * Probe for 16mbit flash memory on a LART board without doing
 305  * too much damage. Since we need to write 1 dword to memory,
 306  * we're f**cked if this happens to be DRAM since we can't
 307  * restore the memory (otherwise we might exit Read Array mode).
 308  *
 309  * Returns 1 if we found 16mbit flash memory on LART, 0 otherwise.
 310  */
 311 static int flash_probe (void)
 312 {
 313    __u32 manufacturer,devtype;
 314
 315    /* setup "Read Identifier Codes" mode */
 316    write32 (DATA_TO_FLASH (READ_ID_CODES),0x00000000);
 317
 318    /* probe U2. U2/U3 returns the same data since the first 3
 319         * address lines is mangled in the same way */
 320    manufacturer = FLASH_TO_DATA (read32 (ADDR_TO_FLASH_U2 (0x00000000)));
 321    devtype = FLASH_TO_DATA (read32 (ADDR_TO_FLASH_U2 (0x00000001)));
 322
 323    /* put the flash back into command mode */
 324    write32 (DATA_TO_FLASH (READ_ARRAY),0x00000000);
 325
 326    return (manufacturer == FLASH_MANUFACTURER && (devtype == FLASH_DEVICE_16mbit_TOP || FLASH_DEVICE_16mbit_BOTTOM));
 327 }
 328
 329 /*
 330  * Erase one block of flash memory at offset ``offset'' which is any
 331  * address within the block which should be erased.
 332  *
 333  * Returns 1 if successful, 0 otherwise.
 334  */
 335 static inline int erase_block (__u32 offset)
 336 {
 337    __u32 status;
 338
 339 #ifdef LART_DEBUG
 340    printk (KERN_DEBUG "%s(): 0x%.8x\n",__FUNCTION__,offset);
 341 #endif
 342
 343    /* erase and confirm */
 344    write32 (DATA_TO_FLASH (ERASE_SETUP),offset);
 345    write32 (DATA_TO_FLASH (ERASE_CONFIRM),offset);
 346
 347    /* wait for block erase to finish */
 348    do
 349          {
 350                 write32 (DATA_TO_FLASH (STATUS_READ),offset);
 351                 status = FLASH_TO_DATA (read32 (offset));
 352          }
 353    while ((~status & STATUS_BUSY) != 0);
 354
 355    /* put the flash back into command mode */
 356    write32 (DATA_TO_FLASH (READ_ARRAY),offset);
 357
 358    /* was the erase successfull? */
 359    if ((status & STATUS_ERASE_ERR))
 360          {
 361                 printk (KERN_WARNING "%s: erase error at address 0x%.8x.\n",module_name,offset);
 362                 return (0);
 363          }
 364
 365    return (1);
 366 }
 367
 368 static int flash_erase (struct mtd_info *mtd,struct erase_info *instr)
 369 {
 370    __u32 addr,len;
 371    int i,first;
 372
 373 #ifdef LART_DEBUG
 374    printk (KERN_DEBUG "%s(addr = 0x%.8x, len = %d)\n",__FUNCTION__,instr->addr,instr->len);
 375 #endif
 376
 377    /* sanity checks */
 378    if (instr->addr + instr->len > mtd->size) return (-EINVAL);
 379
 380    /*
 381         * check that both start and end of the requested erase are
 382         * aligned with the erasesize at the appropriate addresses.
 383         *
 384         * skip all erase regions which are ended before the start of
 385         * the requested erase. Actually, to save on the calculations,
 386         * we skip to the first erase region which starts after the
 387         * start of the requested erase, and then go back one.
 388         */
 389    for (i = 0; i < mtd->numeraseregions && instr->addr >= mtd->eraseregions[i].offset; i++) ;
 390    i--;
 391
 392    /*
 393         * ok, now i is pointing at the erase region in which this
 394         * erase request starts. Check the start of the requested
 395         * erase range is aligned with the erase size which is in
 396         * effect here.
 397         */
 398    if (instr->addr & (mtd->eraseregions[i].erasesize - 1)) return (-EINVAL);
 399
 400    /* Remember the erase region we start on */
 401    first = i;
 402
 403    /*
 404         * next, check that the end of the requested erase is aligned
 405         * with the erase region at that address.
 406         *
 407         * as before, drop back one to point at the region in which
 408         * the address actually falls
 409         */
 410    for (; i < mtd->numeraseregions && instr->addr + instr->len >= mtd->eraseregions[i].offset; i++) ;
 411    i--;
 412
 413    /* is the end aligned on a block boundary? */
 414    if ((instr->addr + instr->len) & (mtd->eraseregions[i].erasesize - 1)) return (-EINVAL);
 415
 416    addr = instr->addr;
 417    len = instr->len;
 418
 419    i = first;
 420
 421    /* now erase those blocks */
 422    while (len)
 423          {
 424                 if (!erase_block (addr))
 425                   {
 426                          instr->state = MTD_ERASE_FAILED;
 427                          return (-EIO);
 428                   }
 429
 430                 addr += mtd->eraseregions[i].erasesize;
 431                 len -= mtd->eraseregions[i].erasesize;
 432
 433                 if (addr == mtd->eraseregions[i].offset + (mtd->eraseregions[i].erasesize * mtd->eraseregions[i].numblocks)) i++;
 434          }
 435
 436    instr->state = MTD_ERASE_DONE;
 437    mtd_erase_callback(instr);
 438
 439    return (0);
 440 }
 441
 442 static int flash_read (struct mtd_info *mtd,loff_t from,size_t len,size_t *retlen,u_char *buf)
 443 {
 444 #ifdef LART_DEBUG
 445    printk (KERN_DEBUG "%s(from = 0x%.8x, len = %d)\n",__FUNCTION__,(__u32) from,len);
 446 #endif
 447
 448    /* sanity checks */
 449    if (!len) return (0);
 450    if (from + len > mtd->size) return (-EINVAL);
 451
 452    /* we always read len bytes */
 453    *retlen = len;
 454
 455    /* first, we read bytes until we reach a dword boundary */
 456    if (from & (BUSWIDTH - 1))
 457          {
 458                 int gap = BUSWIDTH - (from & (BUSWIDTH - 1));
 459
 460                 while (len && gap--) *buf++ = read8 (from++), len--;
 461          }
 462
 463    /* now we read dwords until we reach a non-dword boundary */
 464    while (len >= BUSWIDTH)
 465          {
 466                 *((__u32 *) buf) = read32 (from);
 467
 468                 buf += BUSWIDTH;
 469                 from += BUSWIDTH;
 470                 len -= BUSWIDTH;
 471          }
 472
 473    /* top up the last unaligned bytes */
 474    if (len & (BUSWIDTH - 1))
 475          while (len--) *buf++ = read8 (from++);
 476
 477    return (0);
 478 }
 479
 480 /*
 481  * Write one dword ``x'' to flash memory at offset ``offset''. ``offset''
 482  * must be 32 bits, i.e. it must be on a dword boundary.
 483  *
 484  * Returns 1 if successful, 0 otherwise.
 485  */
 486 static inline int write_dword (__u32 offset,__u32 x)
 487 {
 488    __u32 status;
 489
 490 #ifdef LART_DEBUG
 491    printk (KERN_DEBUG "%s(): 0x%.8x <- 0x%.8x\n",__FUNCTION__,offset,x);
 492 #endif
 493
 494    /* setup writing */
 495    write32 (DATA_TO_FLASH (PGM_SETUP),offset);
 496
 497    /* write the data */
 498    write32 (x,offset);
 499
 500    /* wait for the write to finish */
 501    do
 502          {
 503                 write32 (DATA_TO_FLASH (STATUS_READ),offset);
 504                 status = FLASH_TO_DATA (read32 (offset));
 505          }
 506    while ((~status & STATUS_BUSY) != 0);
 507
 508    /* put the flash back into command mode */
 509    write32 (DATA_TO_FLASH (READ_ARRAY),offset);
 510
 511    /* was the write successfull? */
 512    if ((status & STATUS_PGM_ERR) || read32 (offset) != x)
 513          {
 514                 printk (KERN_WARNING "%s: write error at address 0x%.8x.\n",module_name,offset);
 515                 return (0);
 516          }
 517
 518    return (1);
 519 }
 520
 521 static int flash_write (struct mtd_info *mtd,loff_t to,size_t len,size_t *retlen,const u_char *buf)
 522 {
 523    __u8 tmp[4];
 524    int i,n;
 525
 526 #ifdef LART_DEBUG
 527    printk (KERN_DEBUG "%s(to = 0x%.8x, len = %d)\n",__FUNCTION__,(__u32) to,len);
 528 #endif
 529
 530    *retlen = 0;
 531
 532    /* sanity checks */
 533    if (!len) return (0);
 534    if (to + len > mtd->size) return (-EINVAL);
 535
 536    /* first, we write a 0xFF.... padded byte until we reach a dword boundary */
 537    if (to & (BUSWIDTH - 1))
 538          {
 539                 __u32 aligned = to & ~(BUSWIDTH - 1);
 540                 int gap = to - aligned;
 541
 542                 i = n = 0;
 543
 544                 while (gap--) tmp[i++] = 0xFF;
 545                 while (len && i < BUSWIDTH) tmp[i++] = buf[n++], len--;
 546                 while (i < BUSWIDTH) tmp[i++] = 0xFF;
 547
 548                 if (!write_dword (aligned,*((__u32 *) tmp))) return (-EIO);
 549
 550                 to += n;
 551                 buf += n;
 552                 *retlen += n;
 553          }
 554
 555    /* now we write dwords until we reach a non-dword boundary */
 556    while (len >= BUSWIDTH)
 557          {
 558                 if (!write_dword (to,*((__u32 *) buf))) return (-EIO);
 559
 560                 to += BUSWIDTH;
 561                 buf += BUSWIDTH;
 562                 *retlen += BUSWIDTH;
 563                 len -= BUSWIDTH;
 564          }
 565
 566    /* top up the last unaligned bytes, padded with 0xFF.... */
 567    if (len & (BUSWIDTH - 1))
 568          {
 569                 i = n = 0;
 570
 571                 while (len--) tmp[i++] = buf[n++];
 572                 while (i < BUSWIDTH) tmp[i++] = 0xFF;
 573
 574                 if (!write_dword (to,*((__u32 *) tmp))) return (-EIO);
 575
 576                 *retlen += n;
 577          }
 578
 579    return (0);
 580 }
 581
 582 /***************************************************************************************************/
 583
 584 #define NB_OF(x) (sizeof (x) / sizeof (x[0]))
 585
 586 static struct mtd_info mtd;
 587
 588 static struct mtd_erase_region_info erase_regions[] = {
 589         /* parameter blocks */
 590         {
 591                 .offset         = 0x00000000,
 592                 .erasesize      = FLASH_BLOCKSIZE_PARAM,
 593                 .numblocks      = FLASH_NUMBLOCKS_16m_PARAM,
 594         },
 595         /* main blocks */
 596         {
 597                 .offset  = FLASH_BLOCKSIZE_PARAM * FLASH_NUMBLOCKS_16m_PARAM,
 598                 .erasesize      = FLASH_BLOCKSIZE_MAIN,
 599                 .numblocks      = FLASH_NUMBLOCKS_16m_MAIN,
 600         }
 601 };
 602
 603 #ifdef HAVE_PARTITIONS
 604 static struct mtd_partition lart_partitions[] = {
 605         /* blob */
 606         {
 607                 .name   = "blob",
 608                 .offset = BLOB_START,
 609                 .size   = BLOB_LEN,
 610         },
 611         /* kernel */
 612         {
 613                 .name   = "kernel",
 614                 .offset = KERNEL_START,         /* MTDPART_OFS_APPEND */
 615                 .size   = KERNEL_LEN,
 616         },
 617         /* initial ramdisk / file system */
 618         {
 619                 .name   = "file system",
 620                 .offset = INITRD_START,         /* MTDPART_OFS_APPEND */
 621                 .size   = INITRD_LEN,           /* MTDPART_SIZ_FULL */
 622         }
 623 };
 624 #endif
 625
 626 int __init lart_flash_init (void)
 627 {
 628    int result;
 629    memset (&mtd,0,sizeof (mtd));
 630    printk ("MTD driver for LART. Written by Abraham vd Merwe <abraham@2d3d.co.za>\n");
 631    printk ("%s: Probing for 28F160x3 flash on LART...\n",module_name);
 632    if (!flash_probe ())
 633          {
 634                 printk (KERN_WARNING "%s: Found no LART compatible flash device\n",module_name);
 635                 return (-ENXIO);
 636          }
 637    printk ("%s: This looks like a LART board to me.\n",module_name);
 638    mtd.name = module_name;
 639    mtd.type = MTD_NORFLASH;
 640    mtd.flags = MTD_CAP_NORFLASH;
 641    mtd.size = FLASH_BLOCKSIZE_PARAM * FLASH_NUMBLOCKS_16m_PARAM + FLASH_BLOCKSIZE_MAIN * FLASH_NUMBLOCKS_16m_MAIN;
 642    mtd.erasesize = FLASH_BLOCKSIZE_MAIN;
 643    mtd.numeraseregions = NB_OF (erase_regions);
 644    mtd.eraseregions = erase_regions;
 645    mtd.erase = flash_erase;
 646    mtd.read = flash_read;
 647    mtd.write = flash_write;
 648    mtd.owner = THIS_MODULE;
 649
 650 #ifdef LART_DEBUG
 651    printk (KERN_DEBUG
 652                    "mtd.name = %s\n"
 653                    "mtd.size = 0x%.8x (%uM)\n"
 654                    "mtd.erasesize = 0x%.8x (%uK)\n"
 655                    "mtd.numeraseregions = %d\n",
 656                    mtd.name,
 657                    mtd.size,mtd.size / (1024*1024),
 658                    mtd.erasesize,mtd.erasesize / 1024,
 659                    mtd.numeraseregions);
 660
 661    if (mtd.numeraseregions)
 662          for (result = 0; result < mtd.numeraseregions; result++)
 663            printk (KERN_DEBUG
 664                            "\n\n"
 665                            "mtd.eraseregions[%d].offset = 0x%.8x\n"
 666                            "mtd.eraseregions[%d].erasesize = 0x%.8x (%uK)\n"
 667                            "mtd.eraseregions[%d].numblocks = %d\n",
 668                            result,mtd.eraseregions[result].offset,
 669                            result,mtd.eraseregions[result].erasesize,mtd.eraseregions[result].erasesize / 1024,
 670                            result,mtd.eraseregions[result].numblocks);
 671
 672 #ifdef HAVE_PARTITIONS
 673    printk ("\npartitions = %d\n",NB_OF (lart_partitions));
 674
 675    for (result = 0; result < NB_OF (lart_partitions); result++)
 676          printk (KERN_DEBUG
 677                          "\n\n"
 678                          "lart_partitions[%d].name = %s\n"
 679                          "lart_partitions[%d].offset = 0x%.8x\n"
 680                          "lart_partitions[%d].size = 0x%.8x (%uK)\n",
 681                          result,lart_partitions[result].name,
 682                          result,lart_partitions[result].offset,
 683                          result,lart_partitions[result].size,lart_partitions[result].size / 1024);
 684 #endif
 685 #endif
 686
 687 #ifndef HAVE_PARTITIONS
 688    result = add_mtd_device (&mtd);
 689 #else
 690    result = add_mtd_partitions (&mtd,lart_partitions,NB_OF (lart_partitions));
 691 #endif
 692
 693    return (result);
 694 }
 695
 696 void __exit lart_flash_exit (void)
 697 {
 698 #ifndef HAVE_PARTITIONS
 699    del_mtd_device (&mtd);
 700 #else
 701    del_mtd_partitions (&mtd);
 702 #endif
 703 }
 704
 705 module_init (lart_flash_init);
 706 module_exit (lart_flash_exit);
 707
 708 MODULE_LICENSE("GPL");
 709 MODULE_AUTHOR("Abraham vd Merwe <abraham@2d3d.co.za>");
 710 MODULE_DESCRIPTION("MTD driver for Intel 28F160F3 on LART board");
 711
 712