[TG3]: Add tagged status support.

[linux-2.6/verdex.git] / drivers / i2c / chips / lm85.c

/*
    lm85.c - Part of lm_sensors, Linux kernel modules for hardware
             monitoring
    Copyright (c) 1998, 1999  Frodo Looijaard <frodol@dds.nl> 
    Copyright (c) 2002, 2003  Philip Pokorny <ppokorny@penguincomputing.com>
    Copyright (c) 2003        Margit Schubert-While <margitsw@t-online.de>
    Copyright (c) 2004        Justin Thiessen <jthiessen@penguincomputing.com>

    Chip details at           <http://www.national.com/ds/LM/LM85.pdf>

    This program is free software; you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
    the Free Software Foundation; either version 2 of the License, or
    (at your option) any later version.

    This program is distributed in the hope that it will be useful,
    but WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
    GNU General Public License for more details.

    You should have received a copy of the GNU General Public License
    along with this program; if not, write to the Free Software
    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/

#include <linux/config.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/i2c-sensor.h>
#include <linux/i2c-vid.h>

/* Addresses to scan */
static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
static unsigned int normal_isa[] = { I2C_CLIENT_ISA_END };

/* Insmod parameters */
SENSORS_INSMOD_6(lm85b, lm85c, adm1027, adt7463, emc6d100, emc6d102);

/* The LM85 registers */

#define LM85_REG_IN(nr)                 (0x20 + (nr))
#define LM85_REG_IN_MIN(nr)             (0x44 + (nr) * 2)
#define LM85_REG_IN_MAX(nr)             (0x45 + (nr) * 2)

#define LM85_REG_TEMP(nr)               (0x25 + (nr))
#define LM85_REG_TEMP_MIN(nr)           (0x4e + (nr) * 2)
#define LM85_REG_TEMP_MAX(nr)           (0x4f + (nr) * 2)

/* Fan speeds are LSB, MSB (2 bytes) */
#define LM85_REG_FAN(nr)                (0x28 + (nr) *2)
#define LM85_REG_FAN_MIN(nr)            (0x54 + (nr) *2)

#define LM85_REG_PWM(nr)                (0x30 + (nr))

#define ADT7463_REG_OPPOINT(nr)         (0x33 + (nr))

#define ADT7463_REG_TMIN_CTL1           0x36
#define ADT7463_REG_TMIN_CTL2           0x37

#define LM85_REG_DEVICE                 0x3d
#define LM85_REG_COMPANY                0x3e
#define LM85_REG_VERSTEP                0x3f
/* These are the recognized values for the above regs */
#define LM85_DEVICE_ADX                 0x27
#define LM85_COMPANY_NATIONAL           0x01
#define LM85_COMPANY_ANALOG_DEV         0x41
#define LM85_COMPANY_SMSC               0x5c
#define LM85_VERSTEP_VMASK              0xf0
#define LM85_VERSTEP_GENERIC            0x60
#define LM85_VERSTEP_LM85C              0x60
#define LM85_VERSTEP_LM85B              0x62
#define LM85_VERSTEP_ADM1027            0x60
#define LM85_VERSTEP_ADT7463            0x62
#define LM85_VERSTEP_ADT7463C           0x6A
#define LM85_VERSTEP_EMC6D100_A0        0x60
#define LM85_VERSTEP_EMC6D100_A1        0x61
#define LM85_VERSTEP_EMC6D102           0x65

#define LM85_REG_CONFIG                 0x40

#define LM85_REG_ALARM1                 0x41
#define LM85_REG_ALARM2                 0x42

#define LM85_REG_VID                    0x43

/* Automated FAN control */
#define LM85_REG_AFAN_CONFIG(nr)        (0x5c + (nr))
#define LM85_REG_AFAN_RANGE(nr)         (0x5f + (nr))
#define LM85_REG_AFAN_SPIKE1            0x62
#define LM85_REG_AFAN_SPIKE2            0x63
#define LM85_REG_AFAN_MINPWM(nr)        (0x64 + (nr))
#define LM85_REG_AFAN_LIMIT(nr)         (0x67 + (nr))
#define LM85_REG_AFAN_CRITICAL(nr)      (0x6a + (nr))
#define LM85_REG_AFAN_HYST1             0x6d
#define LM85_REG_AFAN_HYST2             0x6e

#define LM85_REG_TACH_MODE              0x74
#define LM85_REG_SPINUP_CTL             0x75

#define ADM1027_REG_TEMP_OFFSET(nr)     (0x70 + (nr))
#define ADM1027_REG_CONFIG2             0x73
#define ADM1027_REG_INTMASK1            0x74
#define ADM1027_REG_INTMASK2            0x75
#define ADM1027_REG_EXTEND_ADC1         0x76
#define ADM1027_REG_EXTEND_ADC2         0x77
#define ADM1027_REG_CONFIG3             0x78
#define ADM1027_REG_FAN_PPR             0x7b

#define ADT7463_REG_THERM               0x79
#define ADT7463_REG_THERM_LIMIT         0x7A

#define EMC6D100_REG_ALARM3             0x7d
/* IN5, IN6 and IN7 */
#define EMC6D100_REG_IN(nr)             (0x70 + ((nr)-5))
#define EMC6D100_REG_IN_MIN(nr)         (0x73 + ((nr)-5) * 2)
#define EMC6D100_REG_IN_MAX(nr)         (0x74 + ((nr)-5) * 2)
#define EMC6D102_REG_EXTEND_ADC1        0x85
#define EMC6D102_REG_EXTEND_ADC2        0x86
#define EMC6D102_REG_EXTEND_ADC3        0x87
#define EMC6D102_REG_EXTEND_ADC4        0x88

#define LM85_ALARM_IN0                  0x0001
#define LM85_ALARM_IN1                  0x0002
#define LM85_ALARM_IN2                  0x0004
#define LM85_ALARM_IN3                  0x0008
#define LM85_ALARM_TEMP1                0x0010
#define LM85_ALARM_TEMP2                0x0020
#define LM85_ALARM_TEMP3                0x0040
#define LM85_ALARM_ALARM2               0x0080
#define LM85_ALARM_IN4                  0x0100
#define LM85_ALARM_RESERVED             0x0200
#define LM85_ALARM_FAN1                 0x0400
#define LM85_ALARM_FAN2                 0x0800
#define LM85_ALARM_FAN3                 0x1000
#define LM85_ALARM_FAN4                 0x2000
#define LM85_ALARM_TEMP1_FAULT          0x4000
#define LM85_ALARM_TEMP3_FAULT          0x8000


/* Conversions. Rounding and limit checking is only done on the TO_REG 
   variants. Note that you should be a bit careful with which arguments
   these macros are called: arguments may be evaluated more than once.
 */

/* IN are scaled acording to built-in resistors */
static int lm85_scaling[] = {  /* .001 Volts */
                2500, 2250, 3300, 5000, 12000,
                3300, 1500, 1800 /*EMC6D100*/
        };
#define SCALE(val,from,to)              (((val)*(to) + ((from)/2))/(from))

#define INS_TO_REG(n,val)       \
                SENSORS_LIMIT(SCALE(val,lm85_scaling[n],192),0,255)

#define INSEXT_FROM_REG(n,val,ext,scale)        \
                SCALE((val)*(scale) + (ext),192*(scale),lm85_scaling[n])

#define INS_FROM_REG(n,val)   INSEXT_FROM_REG(n,val,0,1)

/* FAN speed is measured using 90kHz clock */
#define FAN_TO_REG(val)         (SENSORS_LIMIT( (val)<=0?0: 5400000/(val),0,65534))
#define FAN_FROM_REG(val)       ((val)==0?-1:(val)==0xffff?0:5400000/(val))

/* Temperature is reported in .001 degC increments */
#define TEMP_TO_REG(val)        \
                SENSORS_LIMIT(SCALE(val,1000,1),-127,127)
#define TEMPEXT_FROM_REG(val,ext,scale) \
                SCALE((val)*scale + (ext),scale,1000)
#define TEMP_FROM_REG(val)      \
                TEMPEXT_FROM_REG(val,0,1)

#define PWM_TO_REG(val)                 (SENSORS_LIMIT(val,0,255))
#define PWM_FROM_REG(val)               (val)


/* ZONEs have the following parameters:
 *    Limit (low) temp,           1. degC
 *    Hysteresis (below limit),   1. degC (0-15)
 *    Range of speed control,     .1 degC (2-80)
 *    Critical (high) temp,       1. degC
 *
 * FAN PWMs have the following parameters:
 *    Reference Zone,                 1, 2, 3, etc.
 *    Spinup time,                    .05 sec
 *    PWM value at limit/low temp,    1 count
 *    PWM Frequency,                  1. Hz
 *    PWM is Min or OFF below limit,  flag
 *    Invert PWM output,              flag
 *
 * Some chips filter the temp, others the fan.
 *    Filter constant (or disabled)   .1 seconds
 */

/* These are the zone temperature range encodings in .001 degree C */
static int lm85_range_map[] = {   
                2000,  2500,  3300,  4000,  5000,  6600,
                8000, 10000, 13300, 16000, 20000, 26600,
                32000, 40000, 53300, 80000
        };
static int RANGE_TO_REG( int range )
{
        int i;

        if ( range < lm85_range_map[0] ) { 
                return 0 ;
        } else if ( range > lm85_range_map[15] ) {
                return 15 ;
        } else {  /* find closest match */
                for ( i = 14 ; i >= 0 ; --i ) {
                        if ( range > lm85_range_map[i] ) { /* range bracketed */
                                if ((lm85_range_map[i+1] - range) < 
                                        (range - lm85_range_map[i])) {
                                        i++;
                                        break;
                                }
                                break;
                        }
                }
        }
        return( i & 0x0f );
}
#define RANGE_FROM_REG(val) (lm85_range_map[(val)&0x0f])

/* These are the Acoustic Enhancement, or Temperature smoothing encodings
 * NOTE: The enable/disable bit is INCLUDED in these encodings as the
 *       MSB (bit 3, value 8).  If the enable bit is 0, the encoded value
 *       is ignored, or set to 0.
 */
/* These are the PWM frequency encodings */
static int lm85_freq_map[] = { /* .1 Hz */
                100, 150, 230, 300, 380, 470, 620, 940
        };
static int FREQ_TO_REG( int freq )
{
        int i;

        if( freq >= lm85_freq_map[7] ) { return 7 ; }
        for( i = 0 ; i < 7 ; ++i )
                if( freq <= lm85_freq_map[i] )
                        break ;
        return( i & 0x07 );
}
#define FREQ_FROM_REG(val) (lm85_freq_map[(val)&0x07])

/* Since we can't use strings, I'm abusing these numbers
 *   to stand in for the following meanings:
 *      1 -- PWM responds to Zone 1
 *      2 -- PWM responds to Zone 2
 *      3 -- PWM responds to Zone 3
 *     23 -- PWM responds to the higher temp of Zone 2 or 3
 *    123 -- PWM responds to highest of Zone 1, 2, or 3
 *      0 -- PWM is always at 0% (ie, off)
 *     -1 -- PWM is always at 100%
 *     -2 -- PWM responds to manual control
 */

static int lm85_zone_map[] = { 1, 2, 3, -1, 0, 23, 123, -2 };
#define ZONE_FROM_REG(val) (lm85_zone_map[((val)>>5)&0x07])

static int ZONE_TO_REG( int zone )
{
        int i;

        for( i = 0 ; i <= 7 ; ++i )
                if( zone == lm85_zone_map[i] )
                        break ;
        if( i > 7 )   /* Not found. */
                i = 3;  /* Always 100% */
        return( (i & 0x07)<<5 );
}

#define HYST_TO_REG(val) (SENSORS_LIMIT(((val)+500)/1000,0,15))
#define HYST_FROM_REG(val) ((val)*1000)

#define OFFSET_TO_REG(val) (SENSORS_LIMIT((val)/25,-127,127))
#define OFFSET_FROM_REG(val) ((val)*25)

#define PPR_MASK(fan) (0x03<<(fan *2))
#define PPR_TO_REG(val,fan) (SENSORS_LIMIT((val)-1,0,3)<<(fan *2))
#define PPR_FROM_REG(val,fan) ((((val)>>(fan * 2))&0x03)+1)

/* i2c-vid.h defines vid_from_reg() */
#define VID_FROM_REG(val,vrm) (vid_from_reg((val),(vrm)))

#define ALARMS_FROM_REG(val) (val)

/* Unlike some other drivers we DO NOT set initial limits.  Use
 * the config file to set limits.  Some users have reported
 * motherboards shutting down when we set limits in a previous
 * version of the driver.
 */

/* Chip sampling rates
 *
 * Some sensors are not updated more frequently than once per second
 *    so it doesn't make sense to read them more often than that.
 *    We cache the results and return the saved data if the driver
 *    is called again before a second has elapsed.
 *
 * Also, there is significant configuration data for this chip
 *    given the automatic PWM fan control that is possible.  There
 *    are about 47 bytes of config data to only 22 bytes of actual
 *    readings.  So, we keep the config data up to date in the cache
 *    when it is written and only sample it once every 1 *minute*
 */
#define LM85_DATA_INTERVAL  (HZ + HZ / 2)
#define LM85_CONFIG_INTERVAL  (1 * 60 * HZ)

/* For each registered LM85, we need to keep some data in memory. That
   data is pointed to by lm85_list[NR]->data. The structure itself is
   dynamically allocated, at the same time when a new lm85 client is
   allocated. */

/* LM85 can automatically adjust fan speeds based on temperature
 * This structure encapsulates an entire Zone config.  There are
 * three zones (one for each temperature input) on the lm85
 */
struct lm85_zone {
        s8 limit;       /* Low temp limit */
        u8 hyst;        /* Low limit hysteresis. (0-15) */
        u8 range;       /* Temp range, encoded */
        s8 critical;    /* "All fans ON" temp limit */
        u8 off_desired; /* Actual "off" temperature specified.  Preserved 
                         * to prevent "drift" as other autofan control
                         * values change.
                         */
        u8 max_desired; /* Actual "max" temperature specified.  Preserved 
                         * to prevent "drift" as other autofan control
                         * values change.
                         */
};

struct lm85_autofan {
        u8 config;      /* Register value */
        u8 freq;        /* PWM frequency, encoded */
        u8 min_pwm;     /* Minimum PWM value, encoded */
        u8 min_off;     /* Min PWM or OFF below "limit", flag */
};

struct lm85_data {
        struct i2c_client client;
        struct semaphore lock;
        enum chips type;

        struct semaphore update_lock;
        int valid;              /* !=0 if following fields are valid */
        unsigned long last_reading;     /* In jiffies */
        unsigned long last_config;      /* In jiffies */

        u8 in[8];               /* Register value */
        u8 in_max[8];           /* Register value */
        u8 in_min[8];           /* Register value */
        s8 temp[3];             /* Register value */
        s8 temp_min[3];         /* Register value */
        s8 temp_max[3];         /* Register value */
        s8 temp_offset[3];      /* Register value */
        u16 fan[4];             /* Register value */
        u16 fan_min[4];         /* Register value */
        u8 pwm[3];              /* Register value */
        u8 spinup_ctl;          /* Register encoding, combined */
        u8 tach_mode;           /* Register encoding, combined */
        u8 temp_ext[3];         /* Decoded values */
        u8 in_ext[8];           /* Decoded values */
        u8 adc_scale;           /* ADC Extended bits scaling factor */
        u8 fan_ppr;             /* Register value */
        u8 smooth[3];           /* Register encoding */
        u8 vid;                 /* Register value */
        u8 vrm;                 /* VRM version */
        u8 syncpwm3;            /* Saved PWM3 for TACH 2,3,4 config */
        u8 oppoint[3];          /* Register value */
        u16 tmin_ctl;           /* Register value */
        unsigned long therm_total; /* Cummulative therm count */
        u8 therm_limit;         /* Register value */
        u32 alarms;             /* Register encoding, combined */
        struct lm85_autofan autofan[3];
        struct lm85_zone zone[3];
};

static int lm85_attach_adapter(struct i2c_adapter *adapter);
static int lm85_detect(struct i2c_adapter *adapter, int address,
                        int kind);
static int lm85_detach_client(struct i2c_client *client);

static int lm85_read_value(struct i2c_client *client, u8 register);
static int lm85_write_value(struct i2c_client *client, u8 register, int value);
static struct lm85_data *lm85_update_device(struct device *dev);
static void lm85_init_client(struct i2c_client *client);


static struct i2c_driver lm85_driver = {
        .owner          = THIS_MODULE,
        .name           = "lm85",
        .id             = I2C_DRIVERID_LM85,
        .flags          = I2C_DF_NOTIFY,
        .attach_adapter = lm85_attach_adapter,
        .detach_client  = lm85_detach_client,
};


/* 4 Fans */
static ssize_t show_fan(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", FAN_FROM_REG(data->fan[nr]) );
}
static ssize_t show_fan_min(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", FAN_FROM_REG(data->fan_min[nr]) );
}
static ssize_t set_fan_min(struct device *dev, const char *buf, 
                size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        data->fan_min[nr] = FAN_TO_REG(val);
        lm85_write_value(client, LM85_REG_FAN_MIN(nr), data->fan_min[nr]);
        up(&data->update_lock);
        return count;
}

#define show_fan_offset(offset)                                         \
static ssize_t show_fan_##offset (struct device *dev, char *buf)        \
{                                                                       \
        return show_fan(dev, buf, offset - 1);                          \
}                                                                       \
static ssize_t show_fan_##offset##_min (struct device *dev, char *buf)  \
{                                                                       \
        return show_fan_min(dev, buf, offset - 1);                      \
}                                                                       \
static ssize_t set_fan_##offset##_min (struct device *dev,              \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_fan_min(dev, buf, count, offset - 1);                \
}                                                                       \
static DEVICE_ATTR(fan##offset##_input, S_IRUGO, show_fan_##offset,     \
                NULL);                                                  \
static DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR,                \
                show_fan_##offset##_min, set_fan_##offset##_min);

show_fan_offset(1);
show_fan_offset(2);
show_fan_offset(3);
show_fan_offset(4);

/* vid, vrm, alarms */

static ssize_t show_vid_reg(struct device *dev, char *buf)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf, "%ld\n", (long) vid_from_reg(data->vid, data->vrm));
}

static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid_reg, NULL);

static ssize_t show_vrm_reg(struct device *dev, char *buf)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf, "%ld\n", (long) data->vrm);
}

static ssize_t store_vrm_reg(struct device *dev, const char *buf, size_t count)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        u32 val;

        val = simple_strtoul(buf, NULL, 10);
        data->vrm = val;
        return count;
}

static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm_reg, store_vrm_reg);

static ssize_t show_alarms_reg(struct device *dev, char *buf)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf, "%ld\n", (long) ALARMS_FROM_REG(data->alarms));
}

static DEVICE_ATTR(alarms, S_IRUGO, show_alarms_reg, NULL);

/* pwm */

static ssize_t show_pwm(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", PWM_FROM_REG(data->pwm[nr]) );
}
static ssize_t set_pwm(struct device *dev, const char *buf, 
                size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        data->pwm[nr] = PWM_TO_REG(val);
        lm85_write_value(client, LM85_REG_PWM(nr), data->pwm[nr]);
        up(&data->update_lock);
        return count;
}
static ssize_t show_pwm_enable(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        int     pwm_zone;

        pwm_zone = ZONE_FROM_REG(data->autofan[nr].config);
        return sprintf(buf,"%d\n", (pwm_zone != 0 && pwm_zone != -1) );
}

#define show_pwm_reg(offset)                                            \
static ssize_t show_pwm_##offset (struct device *dev, char *buf)        \
{                                                                       \
        return show_pwm(dev, buf, offset - 1);                          \
}                                                                       \
static ssize_t set_pwm_##offset (struct device *dev,                    \
                                 const char *buf, size_t count)         \
{                                                                       \
        return set_pwm(dev, buf, count, offset - 1);                    \
}                                                                       \
static ssize_t show_pwm_enable##offset (struct device *dev, char *buf)  \
{                                                                       \
        return show_pwm_enable(dev, buf, offset - 1);                   \
}                                                                       \
static DEVICE_ATTR(pwm##offset, S_IRUGO | S_IWUSR,                      \
                show_pwm_##offset, set_pwm_##offset);                   \
static DEVICE_ATTR(pwm##offset##_enable, S_IRUGO,                       \
                show_pwm_enable##offset, NULL);

show_pwm_reg(1);
show_pwm_reg(2);
show_pwm_reg(3);

/* Voltages */

static ssize_t show_in(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf( buf, "%d\n", INSEXT_FROM_REG(nr,
                                                     data->in[nr],
                                                     data->in_ext[nr],
                                                     data->adc_scale) );
}
static ssize_t show_in_min(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", INS_FROM_REG(nr, data->in_min[nr]) );
}
static ssize_t set_in_min(struct device *dev, const char *buf, 
                size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        data->in_min[nr] = INS_TO_REG(nr, val);
        lm85_write_value(client, LM85_REG_IN_MIN(nr), data->in_min[nr]);
        up(&data->update_lock);
        return count;
}
static ssize_t show_in_max(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", INS_FROM_REG(nr, data->in_max[nr]) );
}
static ssize_t set_in_max(struct device *dev, const char *buf, 
                size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        data->in_max[nr] = INS_TO_REG(nr, val);
        lm85_write_value(client, LM85_REG_IN_MAX(nr), data->in_max[nr]);
        up(&data->update_lock);
        return count;
}
#define show_in_reg(offset)                                             \
static ssize_t show_in_##offset (struct device *dev, char *buf)         \
{                                                                       \
        return show_in(dev, buf, offset);                               \
}                                                                       \
static ssize_t show_in_##offset##_min (struct device *dev, char *buf)   \
{                                                                       \
        return show_in_min(dev, buf, offset);                           \
}                                                                       \
static ssize_t show_in_##offset##_max (struct device *dev, char *buf)   \
{                                                                       \
        return show_in_max(dev, buf, offset);                           \
}                                                                       \
static ssize_t set_in_##offset##_min (struct device *dev,               \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_in_min(dev, buf, count, offset);                     \
}                                                                       \
static ssize_t set_in_##offset##_max (struct device *dev,               \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_in_max(dev, buf, count, offset);                     \
}                                                                       \
static DEVICE_ATTR(in##offset##_input, S_IRUGO, show_in_##offset,       \
                NULL);                                                  \
static DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR,                 \
                show_in_##offset##_min, set_in_##offset##_min);         \
static DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR,                 \
                show_in_##offset##_max, set_in_##offset##_max);

show_in_reg(0);
show_in_reg(1);
show_in_reg(2);
show_in_reg(3);
show_in_reg(4);

/* Temps */

static ssize_t show_temp(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", TEMPEXT_FROM_REG(data->temp[nr],
                                                    data->temp_ext[nr],
                                                    data->adc_scale) );
}
static ssize_t show_temp_min(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp_min[nr]) );
}
static ssize_t set_temp_min(struct device *dev, const char *buf, 
                size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        data->temp_min[nr] = TEMP_TO_REG(val);
        lm85_write_value(client, LM85_REG_TEMP_MIN(nr), data->temp_min[nr]);
        up(&data->update_lock);
        return count;
}
static ssize_t show_temp_max(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp_max[nr]) );
}
static ssize_t set_temp_max(struct device *dev, const char *buf, 
                size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);        

        down(&data->update_lock);
        data->temp_max[nr] = TEMP_TO_REG(val);
        lm85_write_value(client, LM85_REG_TEMP_MAX(nr), data->temp_max[nr]);
        up(&data->update_lock);
        return count;
}
#define show_temp_reg(offset)                                           \
static ssize_t show_temp_##offset (struct device *dev, char *buf)       \
{                                                                       \
        return show_temp(dev, buf, offset - 1);                         \
}                                                                       \
static ssize_t show_temp_##offset##_min (struct device *dev, char *buf) \
{                                                                       \
        return show_temp_min(dev, buf, offset - 1);                     \
}                                                                       \
static ssize_t show_temp_##offset##_max (struct device *dev, char *buf) \
{                                                                       \
        return show_temp_max(dev, buf, offset - 1);                     \
}                                                                       \
static ssize_t set_temp_##offset##_min (struct device *dev,             \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_temp_min(dev, buf, count, offset - 1);               \
}                                                                       \
static ssize_t set_temp_##offset##_max (struct device *dev,             \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_temp_max(dev, buf, count, offset - 1);               \
}                                                                       \
static DEVICE_ATTR(temp##offset##_input, S_IRUGO, show_temp_##offset,   \
                NULL);                                                  \
static DEVICE_ATTR(temp##offset##_min, S_IRUGO | S_IWUSR,               \
                show_temp_##offset##_min, set_temp_##offset##_min);     \
static DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR,               \
                show_temp_##offset##_max, set_temp_##offset##_max);

show_temp_reg(1);
show_temp_reg(2);
show_temp_reg(3);


/* Automatic PWM control */

static ssize_t show_pwm_auto_channels(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", ZONE_FROM_REG(data->autofan[nr].config));
}
static ssize_t set_pwm_auto_channels(struct device *dev, const char *buf,
        size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);   

        down(&data->update_lock);
        data->autofan[nr].config = (data->autofan[nr].config & (~0xe0))
                | ZONE_TO_REG(val) ;
        lm85_write_value(client, LM85_REG_AFAN_CONFIG(nr),
                data->autofan[nr].config);
        up(&data->update_lock);
        return count;
}
static ssize_t show_pwm_auto_pwm_min(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", PWM_FROM_REG(data->autofan[nr].min_pwm));
}
static ssize_t set_pwm_auto_pwm_min(struct device *dev, const char *buf,
        size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        data->autofan[nr].min_pwm = PWM_TO_REG(val);
        lm85_write_value(client, LM85_REG_AFAN_MINPWM(nr),
                data->autofan[nr].min_pwm);
        up(&data->update_lock);
        return count;
}
static ssize_t show_pwm_auto_pwm_minctl(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", data->autofan[nr].min_off);
}
static ssize_t set_pwm_auto_pwm_minctl(struct device *dev, const char *buf,
        size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        data->autofan[nr].min_off = val;
        lm85_write_value(client, LM85_REG_AFAN_SPIKE1, data->smooth[0]
                | data->syncpwm3
                | (data->autofan[0].min_off ? 0x20 : 0)
                | (data->autofan[1].min_off ? 0x40 : 0)
                | (data->autofan[2].min_off ? 0x80 : 0)
        );
        up(&data->update_lock);
        return count;
}
static ssize_t show_pwm_auto_pwm_freq(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", FREQ_FROM_REG(data->autofan[nr].freq));
}
static ssize_t set_pwm_auto_pwm_freq(struct device *dev, const char *buf,
                size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        data->autofan[nr].freq = FREQ_TO_REG(val);
        lm85_write_value(client, LM85_REG_AFAN_RANGE(nr),
                (data->zone[nr].range << 4)
                | data->autofan[nr].freq
        ); 
        up(&data->update_lock);
        return count;
}
#define pwm_auto(offset)                                                \
static ssize_t show_pwm##offset##_auto_channels (struct device *dev,    \
        char *buf)                                                      \
{                                                                       \
        return show_pwm_auto_channels(dev, buf, offset - 1);            \
}                                                                       \
static ssize_t set_pwm##offset##_auto_channels (struct device *dev,     \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_pwm_auto_channels(dev, buf, count, offset - 1);      \
}                                                                       \
static ssize_t show_pwm##offset##_auto_pwm_min (struct device *dev,     \
        char *buf)                                                      \
{                                                                       \
        return show_pwm_auto_pwm_min(dev, buf, offset - 1);             \
}                                                                       \
static ssize_t set_pwm##offset##_auto_pwm_min (struct device *dev,      \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_pwm_auto_pwm_min(dev, buf, count, offset - 1);       \
}                                                                       \
static ssize_t show_pwm##offset##_auto_pwm_minctl (struct device *dev,  \
        char *buf)                                                      \
{                                                                       \
        return show_pwm_auto_pwm_minctl(dev, buf, offset - 1);          \
}                                                                       \
static ssize_t set_pwm##offset##_auto_pwm_minctl (struct device *dev,   \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_pwm_auto_pwm_minctl(dev, buf, count, offset - 1);    \
}                                                                       \
static ssize_t show_pwm##offset##_auto_pwm_freq (struct device *dev,    \
        char *buf)                                                      \
{                                                                       \
        return show_pwm_auto_pwm_freq(dev, buf, offset - 1);            \
}                                                                       \
static ssize_t set_pwm##offset##_auto_pwm_freq(struct device *dev,      \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_pwm_auto_pwm_freq(dev, buf, count, offset - 1);      \
}                                                                       \
static DEVICE_ATTR(pwm##offset##_auto_channels, S_IRUGO | S_IWUSR,      \
                show_pwm##offset##_auto_channels,                       \
                set_pwm##offset##_auto_channels);                       \
static DEVICE_ATTR(pwm##offset##_auto_pwm_min, S_IRUGO | S_IWUSR,       \
                show_pwm##offset##_auto_pwm_min,                        \
                set_pwm##offset##_auto_pwm_min);                        \
static DEVICE_ATTR(pwm##offset##_auto_pwm_minctl, S_IRUGO | S_IWUSR,    \
                show_pwm##offset##_auto_pwm_minctl,                     \
                set_pwm##offset##_auto_pwm_minctl);                     \
static DEVICE_ATTR(pwm##offset##_auto_pwm_freq, S_IRUGO | S_IWUSR,      \
                show_pwm##offset##_auto_pwm_freq,                       \
                set_pwm##offset##_auto_pwm_freq);              
pwm_auto(1);
pwm_auto(2);
pwm_auto(3);

/* Temperature settings for automatic PWM control */

static ssize_t show_temp_auto_temp_off(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", TEMP_FROM_REG(data->zone[nr].limit) -
                HYST_FROM_REG(data->zone[nr].hyst));
}
static ssize_t set_temp_auto_temp_off(struct device *dev, const char *buf,
        size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        int min;
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        min = TEMP_FROM_REG(data->zone[nr].limit);
        data->zone[nr].off_desired = TEMP_TO_REG(val);
        data->zone[nr].hyst = HYST_TO_REG(min - val);
        if ( nr == 0 || nr == 1 ) {
                lm85_write_value(client, LM85_REG_AFAN_HYST1,
                        (data->zone[0].hyst << 4)
                        | data->zone[1].hyst
                        );
        } else {
                lm85_write_value(client, LM85_REG_AFAN_HYST2,
                        (data->zone[2].hyst << 4)
                );
        }
        up(&data->update_lock);
        return count;
}
static ssize_t show_temp_auto_temp_min(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", TEMP_FROM_REG(data->zone[nr].limit) );
}
static ssize_t set_temp_auto_temp_min(struct device *dev, const char *buf,
        size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        data->zone[nr].limit = TEMP_TO_REG(val);
        lm85_write_value(client, LM85_REG_AFAN_LIMIT(nr),
                data->zone[nr].limit);

/* Update temp_auto_max and temp_auto_range */
        data->zone[nr].range = RANGE_TO_REG(
                TEMP_FROM_REG(data->zone[nr].max_desired) -
                TEMP_FROM_REG(data->zone[nr].limit));
        lm85_write_value(client, LM85_REG_AFAN_RANGE(nr),
                ((data->zone[nr].range & 0x0f) << 4)
                | (data->autofan[nr].freq & 0x07));

/* Update temp_auto_hyst and temp_auto_off */
        data->zone[nr].hyst = HYST_TO_REG(TEMP_FROM_REG(
                data->zone[nr].limit) - TEMP_FROM_REG(
                data->zone[nr].off_desired));
        if ( nr == 0 || nr == 1 ) {
                lm85_write_value(client, LM85_REG_AFAN_HYST1,
                        (data->zone[0].hyst << 4)
                        | data->zone[1].hyst
                        );
        } else {
                lm85_write_value(client, LM85_REG_AFAN_HYST2,
                        (data->zone[2].hyst << 4)
                );
        }
        up(&data->update_lock);
        return count;
}
static ssize_t show_temp_auto_temp_max(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", TEMP_FROM_REG(data->zone[nr].limit) +
                RANGE_FROM_REG(data->zone[nr].range));
}
static ssize_t set_temp_auto_temp_max(struct device *dev, const char *buf,
        size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        int min;
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        min = TEMP_FROM_REG(data->zone[nr].limit);
        data->zone[nr].max_desired = TEMP_TO_REG(val);
        data->zone[nr].range = RANGE_TO_REG(
                val - min);
        lm85_write_value(client, LM85_REG_AFAN_RANGE(nr),
                ((data->zone[nr].range & 0x0f) << 4)
                | (data->autofan[nr].freq & 0x07));
        up(&data->update_lock);
        return count;
}
static ssize_t show_temp_auto_temp_crit(struct device *dev, char *buf, int nr)
{
        struct lm85_data *data = lm85_update_device(dev);
        return sprintf(buf,"%d\n", TEMP_FROM_REG(data->zone[nr].critical));
}
static ssize_t set_temp_auto_temp_crit(struct device *dev, const char *buf,
                size_t count, int nr)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        long val = simple_strtol(buf, NULL, 10);

        down(&data->update_lock);
        data->zone[nr].critical = TEMP_TO_REG(val);
        lm85_write_value(client, LM85_REG_AFAN_CRITICAL(nr),
                data->zone[nr].critical);
        up(&data->update_lock);
        return count;
}
#define temp_auto(offset)                                               \
static ssize_t show_temp##offset##_auto_temp_off (struct device *dev,   \
        char *buf)                                                      \
{                                                                       \
        return show_temp_auto_temp_off(dev, buf, offset - 1);           \
}                                                                       \
static ssize_t set_temp##offset##_auto_temp_off (struct device *dev,    \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_temp_auto_temp_off(dev, buf, count, offset - 1);     \
}                                                                       \
static ssize_t show_temp##offset##_auto_temp_min (struct device *dev,   \
        char *buf)                                                      \
{                                                                       \
        return show_temp_auto_temp_min(dev, buf, offset - 1);           \
}                                                                       \
static ssize_t set_temp##offset##_auto_temp_min (struct device *dev,    \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_temp_auto_temp_min(dev, buf, count, offset - 1);     \
}                                                                       \
static ssize_t show_temp##offset##_auto_temp_max (struct device *dev,   \
        char *buf)                                                      \
{                                                                       \
        return show_temp_auto_temp_max(dev, buf, offset - 1);           \
}                                                                       \
static ssize_t set_temp##offset##_auto_temp_max (struct device *dev,    \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_temp_auto_temp_max(dev, buf, count, offset - 1);     \
}                                                                       \
static ssize_t show_temp##offset##_auto_temp_crit (struct device *dev,  \
        char *buf)                                                      \
{                                                                       \
        return show_temp_auto_temp_crit(dev, buf, offset - 1);          \
}                                                                       \
static ssize_t set_temp##offset##_auto_temp_crit (struct device *dev,   \
        const char *buf, size_t count)                                  \
{                                                                       \
        return set_temp_auto_temp_crit(dev, buf, count, offset - 1);    \
}                                                                       \
static DEVICE_ATTR(temp##offset##_auto_temp_off, S_IRUGO | S_IWUSR,     \
                show_temp##offset##_auto_temp_off,                      \
                set_temp##offset##_auto_temp_off);                      \
static DEVICE_ATTR(temp##offset##_auto_temp_min, S_IRUGO | S_IWUSR,     \
                show_temp##offset##_auto_temp_min,                      \
                set_temp##offset##_auto_temp_min);                      \
static DEVICE_ATTR(temp##offset##_auto_temp_max, S_IRUGO | S_IWUSR,     \
                show_temp##offset##_auto_temp_max,                      \
                set_temp##offset##_auto_temp_max);                      \
static DEVICE_ATTR(temp##offset##_auto_temp_crit, S_IRUGO | S_IWUSR,    \
                show_temp##offset##_auto_temp_crit,                     \
                set_temp##offset##_auto_temp_crit);
temp_auto(1);
temp_auto(2);
temp_auto(3);

int lm85_attach_adapter(struct i2c_adapter *adapter)
{
        if (!(adapter->class & I2C_CLASS_HWMON))
                return 0;
        return i2c_detect(adapter, &addr_data, lm85_detect);
}

int lm85_detect(struct i2c_adapter *adapter, int address,
                int kind)
{
        int company, verstep ;
        struct i2c_client *new_client = NULL;
        struct lm85_data *data;
        int err = 0;
        const char *type_name = "";

        if (i2c_is_isa_adapter(adapter)) {
                /* This chip has no ISA interface */
                goto ERROR0 ;
        };

        if (!i2c_check_functionality(adapter,
                                        I2C_FUNC_SMBUS_BYTE_DATA)) {
                /* We need to be able to do byte I/O */
                goto ERROR0 ;
        };

        /* OK. For now, we presume we have a valid client. We now create the
           client structure, even though we cannot fill it completely yet.
           But it allows us to access lm85_{read,write}_value. */

        if (!(data = kmalloc(sizeof(struct lm85_data), GFP_KERNEL))) {
                err = -ENOMEM;
                goto ERROR0;
        }
        memset(data, 0, sizeof(struct lm85_data));

        new_client = &data->client;
        i2c_set_clientdata(new_client, data);
        new_client->addr = address;
        new_client->adapter = adapter;
        new_client->driver = &lm85_driver;
        new_client->flags = 0;

        /* Now, we do the remaining detection. */

        company = lm85_read_value(new_client, LM85_REG_COMPANY);
        verstep = lm85_read_value(new_client, LM85_REG_VERSTEP);

        dev_dbg(&adapter->dev, "Detecting device at %d,0x%02x with"
                " COMPANY: 0x%02x and VERSTEP: 0x%02x\n",
                i2c_adapter_id(new_client->adapter), new_client->addr,
                company, verstep);

        /* If auto-detecting, Determine the chip type. */
        if (kind <= 0) {
                dev_dbg(&adapter->dev, "Autodetecting device at %d,0x%02x ...\n",
                        i2c_adapter_id(adapter), address );
                if( company == LM85_COMPANY_NATIONAL
                    && verstep == LM85_VERSTEP_LM85C ) {
                        kind = lm85c ;
                } else if( company == LM85_COMPANY_NATIONAL
                    && verstep == LM85_VERSTEP_LM85B ) {
                        kind = lm85b ;
                } else if( company == LM85_COMPANY_NATIONAL
                    && (verstep & LM85_VERSTEP_VMASK) == LM85_VERSTEP_GENERIC ) {
                        dev_err(&adapter->dev, "Unrecognized version/stepping 0x%02x"
                                " Defaulting to LM85.\n", verstep);
                        kind = any_chip ;
                } else if( company == LM85_COMPANY_ANALOG_DEV
                    && verstep == LM85_VERSTEP_ADM1027 ) {
                        kind = adm1027 ;
                } else if( company == LM85_COMPANY_ANALOG_DEV
                    && (verstep == LM85_VERSTEP_ADT7463
                         || verstep == LM85_VERSTEP_ADT7463C) ) {
                        kind = adt7463 ;
                } else if( company == LM85_COMPANY_ANALOG_DEV
                    && (verstep & LM85_VERSTEP_VMASK) == LM85_VERSTEP_GENERIC ) {
                        dev_err(&adapter->dev, "Unrecognized version/stepping 0x%02x"
                                " Defaulting to Generic LM85.\n", verstep );
                        kind = any_chip ;
                } else if( company == LM85_COMPANY_SMSC
                    && (verstep == LM85_VERSTEP_EMC6D100_A0
                         || verstep == LM85_VERSTEP_EMC6D100_A1) ) {
                        /* Unfortunately, we can't tell a '100 from a '101
                         * from the registers.  Since a '101 is a '100
                         * in a package with fewer pins and therefore no
                         * 3.3V, 1.5V or 1.8V inputs, perhaps if those
                         * inputs read 0, then it's a '101.
                         */
                        kind = emc6d100 ;
                } else if( company == LM85_COMPANY_SMSC
                    && verstep == LM85_VERSTEP_EMC6D102) {
                        kind = emc6d102 ;
                } else if( company == LM85_COMPANY_SMSC
                    && (verstep & LM85_VERSTEP_VMASK) == LM85_VERSTEP_GENERIC) {
                        dev_err(&adapter->dev, "lm85: Detected SMSC chip\n");
                        dev_err(&adapter->dev, "lm85: Unrecognized version/stepping 0x%02x"
                            " Defaulting to Generic LM85.\n", verstep );
                        kind = any_chip ;
                } else if( kind == any_chip
                    && (verstep & LM85_VERSTEP_VMASK) == LM85_VERSTEP_GENERIC) {
                        dev_err(&adapter->dev, "Generic LM85 Version 6 detected\n");
                        /* Leave kind as "any_chip" */
                } else {
                        dev_dbg(&adapter->dev, "Autodetection failed\n");
                        /* Not an LM85 ... */
                        if( kind == any_chip ) {  /* User used force=x,y */
                                dev_err(&adapter->dev, "Generic LM85 Version 6 not"
                                        " found at %d,0x%02x. Try force_lm85c.\n",
                                        i2c_adapter_id(adapter), address );
                        }
                        err = 0 ;
                        goto ERROR1;
                }
        }

        /* Fill in the chip specific driver values */
        if ( kind == any_chip ) {
                type_name = "lm85";
        } else if ( kind == lm85b ) {
                type_name = "lm85b";
        } else if ( kind == lm85c ) {
                type_name = "lm85c";
        } else if ( kind == adm1027 ) {
                type_name = "adm1027";
        } else if ( kind == adt7463 ) {
                type_name = "adt7463";
        } else if ( kind == emc6d100){
                type_name = "emc6d100";
        } else if ( kind == emc6d102 ) {
                type_name = "emc6d102";
        }
        strlcpy(new_client->name, type_name, I2C_NAME_SIZE);

        /* Fill in the remaining client fields */
        data->type = kind;
        data->valid = 0;
        init_MUTEX(&data->update_lock);

        /* Tell the I2C layer a new client has arrived */
        if ((err = i2c_attach_client(new_client)))
                goto ERROR1;

        /* Set the VRM version */
        data->vrm = i2c_which_vrm();

        /* Initialize the LM85 chip */
        lm85_init_client(new_client);

        /* Register sysfs hooks */
        device_create_file(&new_client->dev, &dev_attr_fan1_input);
        device_create_file(&new_client->dev, &dev_attr_fan2_input);
        device_create_file(&new_client->dev, &dev_attr_fan3_input);
        device_create_file(&new_client->dev, &dev_attr_fan4_input);
        device_create_file(&new_client->dev, &dev_attr_fan1_min);
        device_create_file(&new_client->dev, &dev_attr_fan2_min);
        device_create_file(&new_client->dev, &dev_attr_fan3_min);
        device_create_file(&new_client->dev, &dev_attr_fan4_min);
        device_create_file(&new_client->dev, &dev_attr_pwm1);
        device_create_file(&new_client->dev, &dev_attr_pwm2);
        device_create_file(&new_client->dev, &dev_attr_pwm3);
        device_create_file(&new_client->dev, &dev_attr_pwm1_enable);
        device_create_file(&new_client->dev, &dev_attr_pwm2_enable);
        device_create_file(&new_client->dev, &dev_attr_pwm3_enable);
        device_create_file(&new_client->dev, &dev_attr_in0_input);
        device_create_file(&new_client->dev, &dev_attr_in1_input);
        device_create_file(&new_client->dev, &dev_attr_in2_input);
        device_create_file(&new_client->dev, &dev_attr_in3_input);
        device_create_file(&new_client->dev, &dev_attr_in4_input);
        device_create_file(&new_client->dev, &dev_attr_in0_min);
        device_create_file(&new_client->dev, &dev_attr_in1_min);
        device_create_file(&new_client->dev, &dev_attr_in2_min);
        device_create_file(&new_client->dev, &dev_attr_in3_min);
        device_create_file(&new_client->dev, &dev_attr_in4_min);
        device_create_file(&new_client->dev, &dev_attr_in0_max);
        device_create_file(&new_client->dev, &dev_attr_in1_max);
        device_create_file(&new_client->dev, &dev_attr_in2_max);
        device_create_file(&new_client->dev, &dev_attr_in3_max);
        device_create_file(&new_client->dev, &dev_attr_in4_max);
        device_create_file(&new_client->dev, &dev_attr_temp1_input);
        device_create_file(&new_client->dev, &dev_attr_temp2_input);
        device_create_file(&new_client->dev, &dev_attr_temp3_input);
        device_create_file(&new_client->dev, &dev_attr_temp1_min);
        device_create_file(&new_client->dev, &dev_attr_temp2_min);
        device_create_file(&new_client->dev, &dev_attr_temp3_min);
        device_create_file(&new_client->dev, &dev_attr_temp1_max);
        device_create_file(&new_client->dev, &dev_attr_temp2_max);
        device_create_file(&new_client->dev, &dev_attr_temp3_max);
        device_create_file(&new_client->dev, &dev_attr_vrm);
        device_create_file(&new_client->dev, &dev_attr_cpu0_vid);
        device_create_file(&new_client->dev, &dev_attr_alarms);
        device_create_file(&new_client->dev, &dev_attr_pwm1_auto_channels);
        device_create_file(&new_client->dev, &dev_attr_pwm2_auto_channels);
        device_create_file(&new_client->dev, &dev_attr_pwm3_auto_channels);
        device_create_file(&new_client->dev, &dev_attr_pwm1_auto_pwm_min);
        device_create_file(&new_client->dev, &dev_attr_pwm2_auto_pwm_min);
        device_create_file(&new_client->dev, &dev_attr_pwm3_auto_pwm_min);
        device_create_file(&new_client->dev, &dev_attr_pwm1_auto_pwm_minctl);
        device_create_file(&new_client->dev, &dev_attr_pwm2_auto_pwm_minctl);
        device_create_file(&new_client->dev, &dev_attr_pwm3_auto_pwm_minctl);
        device_create_file(&new_client->dev, &dev_attr_pwm1_auto_pwm_freq);
        device_create_file(&new_client->dev, &dev_attr_pwm2_auto_pwm_freq);
        device_create_file(&new_client->dev, &dev_attr_pwm3_auto_pwm_freq);
        device_create_file(&new_client->dev, &dev_attr_temp1_auto_temp_off);
        device_create_file(&new_client->dev, &dev_attr_temp2_auto_temp_off);
        device_create_file(&new_client->dev, &dev_attr_temp3_auto_temp_off);
        device_create_file(&new_client->dev, &dev_attr_temp1_auto_temp_min);
        device_create_file(&new_client->dev, &dev_attr_temp2_auto_temp_min);
        device_create_file(&new_client->dev, &dev_attr_temp3_auto_temp_min);
        device_create_file(&new_client->dev, &dev_attr_temp1_auto_temp_max);
        device_create_file(&new_client->dev, &dev_attr_temp2_auto_temp_max);
        device_create_file(&new_client->dev, &dev_attr_temp3_auto_temp_max);
        device_create_file(&new_client->dev, &dev_attr_temp1_auto_temp_crit);
        device_create_file(&new_client->dev, &dev_attr_temp2_auto_temp_crit);
        device_create_file(&new_client->dev, &dev_attr_temp3_auto_temp_crit);

        return 0;

        /* Error out and cleanup code */
    ERROR1:
        kfree(data);
    ERROR0:
        return err;
}

int lm85_detach_client(struct i2c_client *client)
{
        i2c_detach_client(client);
        kfree(i2c_get_clientdata(client));
        return 0;
}


int lm85_read_value(struct i2c_client *client, u8 reg)
{
        int res;

        /* What size location is it? */
        switch( reg ) {
        case LM85_REG_FAN(0) :  /* Read WORD data */
        case LM85_REG_FAN(1) :
        case LM85_REG_FAN(2) :
        case LM85_REG_FAN(3) :
        case LM85_REG_FAN_MIN(0) :
        case LM85_REG_FAN_MIN(1) :
        case LM85_REG_FAN_MIN(2) :
        case LM85_REG_FAN_MIN(3) :
        case LM85_REG_ALARM1 :  /* Read both bytes at once */
                res = i2c_smbus_read_byte_data(client, reg) & 0xff ;
                res |= i2c_smbus_read_byte_data(client, reg+1) << 8 ;
                break ;
        case ADT7463_REG_TMIN_CTL1 :  /* Read WORD MSB, LSB */
                res = i2c_smbus_read_byte_data(client, reg) << 8 ;
                res |= i2c_smbus_read_byte_data(client, reg+1) & 0xff ;
                break ;
        default:        /* Read BYTE data */
                res = i2c_smbus_read_byte_data(client, reg);
                break ;
        }

        return res ;
}

int lm85_write_value(struct i2c_client *client, u8 reg, int value)
{
        int res ;

        switch( reg ) {
        case LM85_REG_FAN(0) :  /* Write WORD data */
        case LM85_REG_FAN(1) :
        case LM85_REG_FAN(2) :
        case LM85_REG_FAN(3) :
        case LM85_REG_FAN_MIN(0) :
        case LM85_REG_FAN_MIN(1) :
        case LM85_REG_FAN_MIN(2) :
        case LM85_REG_FAN_MIN(3) :
        /* NOTE: ALARM is read only, so not included here */
                res = i2c_smbus_write_byte_data(client, reg, value & 0xff) ;
                res |= i2c_smbus_write_byte_data(client, reg+1, (value>>8) & 0xff) ;
                break ;
        case ADT7463_REG_TMIN_CTL1 :  /* Write WORD MSB, LSB */
                res = i2c_smbus_write_byte_data(client, reg, (value>>8) & 0xff);
                res |= i2c_smbus_write_byte_data(client, reg+1, value & 0xff) ;
                break ;
        default:        /* Write BYTE data */
                res = i2c_smbus_write_byte_data(client, reg, value);
                break ;
        }

        return res ;
}

void lm85_init_client(struct i2c_client *client)
{
        int value;
        struct lm85_data *data = i2c_get_clientdata(client);

        dev_dbg(&client->dev, "Initializing device\n");

        /* Warn if part was not "READY" */
        value = lm85_read_value(client, LM85_REG_CONFIG);
        dev_dbg(&client->dev, "LM85_REG_CONFIG is: 0x%02x\n", value);
        if( value & 0x02 ) {
                dev_err(&client->dev, "Client (%d,0x%02x) config is locked.\n",
                            i2c_adapter_id(client->adapter), client->addr );
        };
        if( ! (value & 0x04) ) {
                dev_err(&client->dev, "Client (%d,0x%02x) is not ready.\n",
                            i2c_adapter_id(client->adapter), client->addr );
        };
        if( value & 0x10
            && ( data->type == adm1027
                || data->type == adt7463 ) ) {
                dev_err(&client->dev, "Client (%d,0x%02x) VxI mode is set.  "
                        "Please report this to the lm85 maintainer.\n",
                            i2c_adapter_id(client->adapter), client->addr );
        };

        /* WE INTENTIONALLY make no changes to the limits,
         *   offsets, pwms, fans and zones.  If they were
         *   configured, we don't want to mess with them.
         *   If they weren't, the default is 100% PWM, no
         *   control and will suffice until 'sensors -s'
         *   can be run by the user.
         */

        /* Start monitoring */
        value = lm85_read_value(client, LM85_REG_CONFIG);
        /* Try to clear LOCK, Set START, save everything else */
        value = (value & ~ 0x02) | 0x01 ;
        dev_dbg(&client->dev, "Setting CONFIG to: 0x%02x\n", value);
        lm85_write_value(client, LM85_REG_CONFIG, value);
}

static struct lm85_data *lm85_update_device(struct device *dev)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct lm85_data *data = i2c_get_clientdata(client);
        int i;

        down(&data->update_lock);

        if ( !data->valid ||
             time_after(jiffies, data->last_reading + LM85_DATA_INTERVAL) ) {
                /* Things that change quickly */
                dev_dbg(&client->dev, "Reading sensor values\n");
                
                /* Have to read extended bits first to "freeze" the
                 * more significant bits that are read later.
                 */
                if ( (data->type == adm1027) || (data->type == adt7463) ) {
                        int ext1 = lm85_read_value(client,
                                                   ADM1027_REG_EXTEND_ADC1);
                        int ext2 =  lm85_read_value(client,
                                                    ADM1027_REG_EXTEND_ADC2);
                        int val = (ext1 << 8) + ext2;

                        for(i = 0; i <= 4; i++)
                                data->in_ext[i] = (val>>(i * 2))&0x03;

                        for(i = 0; i <= 2; i++)
                                data->temp_ext[i] = (val>>((i + 5) * 2))&0x03;
                }

                /* adc_scale is 2^(number of LSBs). There are 4 extra bits in
                   the emc6d102 and 2 in the adt7463 and adm1027. In all
                   other chips ext is always 0 and the value of scale is
                   irrelevant. So it is left in 4*/
                data->adc_scale = (data->type == emc6d102 ) ? 16 : 4;

                for (i = 0; i <= 4; ++i) {
                        data->in[i] =
                            lm85_read_value(client, LM85_REG_IN(i));
                }

                for (i = 0; i <= 3; ++i) {
                        data->fan[i] =
                            lm85_read_value(client, LM85_REG_FAN(i));
                }

                for (i = 0; i <= 2; ++i) {
                        data->temp[i] =
                            lm85_read_value(client, LM85_REG_TEMP(i));
                }

                for (i = 0; i <= 2; ++i) {
                        data->pwm[i] =
                            lm85_read_value(client, LM85_REG_PWM(i));
                }

                data->alarms = lm85_read_value(client, LM85_REG_ALARM1);

                if ( data->type == adt7463 ) {
                        if( data->therm_total < ULONG_MAX - 256 ) {
                            data->therm_total +=
                                lm85_read_value(client, ADT7463_REG_THERM );
                        }
                } else if ( data->type == emc6d100 ) {
                        /* Three more voltage sensors */
                        for (i = 5; i <= 7; ++i) {
                                data->in[i] =
                                        lm85_read_value(client, EMC6D100_REG_IN(i));
                        }
                        /* More alarm bits */
                        data->alarms |=
                                lm85_read_value(client, EMC6D100_REG_ALARM3) << 16;
                } else if (data->type == emc6d102 ) {
                        /* Have to read LSB bits after the MSB ones because
                           the reading of the MSB bits has frozen the
                           LSBs (backward from the ADM1027).
                         */
                        int ext1 = lm85_read_value(client,
                                                   EMC6D102_REG_EXTEND_ADC1);
                        int ext2 = lm85_read_value(client,
                                                   EMC6D102_REG_EXTEND_ADC2);
                        int ext3 = lm85_read_value(client,
                                                   EMC6D102_REG_EXTEND_ADC3);
                        int ext4 = lm85_read_value(client,
                                                   EMC6D102_REG_EXTEND_ADC4);
                        data->in_ext[0] = ext3 & 0x0f;
                        data->in_ext[1] = ext4 & 0x0f;
                        data->in_ext[2] = (ext4 >> 4) & 0x0f;
                        data->in_ext[3] = (ext3 >> 4) & 0x0f;
                        data->in_ext[4] = (ext2 >> 4) & 0x0f;

                        data->temp_ext[0] = ext1 & 0x0f;
                        data->temp_ext[1] = ext2 & 0x0f;
                        data->temp_ext[2] = (ext1 >> 4) & 0x0f;
                }

                data->last_reading = jiffies ;
        };  /* last_reading */

        if ( !data->valid ||
             time_after(jiffies, data->last_config + LM85_CONFIG_INTERVAL) ) {
                /* Things that don't change often */
                dev_dbg(&client->dev, "Reading config values\n");

                for (i = 0; i <= 4; ++i) {
                        data->in_min[i] =
                            lm85_read_value(client, LM85_REG_IN_MIN(i));
                        data->in_max[i] =
                            lm85_read_value(client, LM85_REG_IN_MAX(i));
                }

                if ( data->type == emc6d100 ) {
                        for (i = 5; i <= 7; ++i) {
                                data->in_min[i] =
                                        lm85_read_value(client, EMC6D100_REG_IN_MIN(i));
                                data->in_max[i] =
                                        lm85_read_value(client, EMC6D100_REG_IN_MAX(i));
                        }
                }

                for (i = 0; i <= 3; ++i) {
                        data->fan_min[i] =
                            lm85_read_value(client, LM85_REG_FAN_MIN(i));
                }

                for (i = 0; i <= 2; ++i) {
                        data->temp_min[i] =
                            lm85_read_value(client, LM85_REG_TEMP_MIN(i));
                        data->temp_max[i] =
                            lm85_read_value(client, LM85_REG_TEMP_MAX(i));
                }

                data->vid = lm85_read_value(client, LM85_REG_VID);

                for (i = 0; i <= 2; ++i) {
                        int val ;
                        data->autofan[i].config =
                            lm85_read_value(client, LM85_REG_AFAN_CONFIG(i));
                        val = lm85_read_value(client, LM85_REG_AFAN_RANGE(i));
                        data->autofan[i].freq = val & 0x07 ;
                        data->zone[i].range = (val >> 4) & 0x0f ;
                        data->autofan[i].min_pwm =
                            lm85_read_value(client, LM85_REG_AFAN_MINPWM(i));
                        data->zone[i].limit =
                            lm85_read_value(client, LM85_REG_AFAN_LIMIT(i));
                        data->zone[i].critical =
                            lm85_read_value(client, LM85_REG_AFAN_CRITICAL(i));
                }

                i = lm85_read_value(client, LM85_REG_AFAN_SPIKE1);
                data->smooth[0] = i & 0x0f ;
                data->syncpwm3 = i & 0x10 ;  /* Save PWM3 config */
                data->autofan[0].min_off = (i & 0x20) != 0 ;
                data->autofan[1].min_off = (i & 0x40) != 0 ;
                data->autofan[2].min_off = (i & 0x80) != 0 ;
                i = lm85_read_value(client, LM85_REG_AFAN_SPIKE2);
                data->smooth[1] = (i>>4) & 0x0f ;
                data->smooth[2] = i & 0x0f ;

                i = lm85_read_value(client, LM85_REG_AFAN_HYST1);
                data->zone[0].hyst = (i>>4) & 0x0f ;
                data->zone[1].hyst = i & 0x0f ;

                i = lm85_read_value(client, LM85_REG_AFAN_HYST2);
                data->zone[2].hyst = (i>>4) & 0x0f ;

                if ( (data->type == lm85b) || (data->type == lm85c) ) {
                        data->tach_mode = lm85_read_value(client,
                                LM85_REG_TACH_MODE );
                        data->spinup_ctl = lm85_read_value(client,
                                LM85_REG_SPINUP_CTL );
                } else if ( (data->type == adt7463) || (data->type == adm1027) ) {
                        if ( data->type == adt7463 ) {
                                for (i = 0; i <= 2; ++i) {
                                    data->oppoint[i] = lm85_read_value(client,
                                        ADT7463_REG_OPPOINT(i) );
                                }
                                data->tmin_ctl = lm85_read_value(client,
                                        ADT7463_REG_TMIN_CTL1 );
                                data->therm_limit = lm85_read_value(client,
                                        ADT7463_REG_THERM_LIMIT );
                        }
                        for (i = 0; i <= 2; ++i) {
                            data->temp_offset[i] = lm85_read_value(client,
                                ADM1027_REG_TEMP_OFFSET(i) );
                        }
                        data->tach_mode = lm85_read_value(client,
                                ADM1027_REG_CONFIG3 );
                        data->fan_ppr = lm85_read_value(client,
                                ADM1027_REG_FAN_PPR );
                }
        
                data->last_config = jiffies;
        };  /* last_config */

        data->valid = 1;

        up(&data->update_lock);

        return data;
}


static int __init sm_lm85_init(void)
{
        return i2c_add_driver(&lm85_driver);
}

static void  __exit sm_lm85_exit(void)
{
        i2c_del_driver(&lm85_driver);
}

/* Thanks to Richard Barrington for adding the LM85 to sensors-detect.
 * Thanks to Margit Schubert-While <margitsw@t-online.de> for help with
 *     post 2.7.0 CVS changes.
 */
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Philip Pokorny <ppokorny@penguincomputing.com>, Margit Schubert-While <margitsw@t-online.de>, Justin Thiessen <jthiessen@penguincomputing.com");
MODULE_DESCRIPTION("LM85-B, LM85-C driver");

module_init(sm_lm85_init);
module_exit(sm_lm85_exit);