arch/m68k/include/asm/m5249sim.h

   1 /****************************************************************************/
   2
   3 /*
   4  *      m5249sim.h -- ColdFire 5249 System Integration Module support.
   5  *
   6  *      (C) Copyright 2002, Greg Ungerer (gerg@snapgear.com)
   7  */
   8
   9 /****************************************************************************/
  10 #ifndef m5249sim_h
  11 #define m5249sim_h
  12 /****************************************************************************/
  13
  14 #define CPU_NAME                "COLDFIRE(m5249)"
  15 #define CPU_INSTR_PER_JIFFY     3
  16 #define MCF_BUSCLK              (MCF_CLK / 2)
  17
  18 #include <asm/m52xxacr.h>
  19
  20 /*
  21  *      The 5249 has a second MBAR region, define its address.
  22  */
  23 #define MCF_MBAR2               0x80000000
  24
  25 /*
  26  *      Define the 5249 SIM register set addresses.
  27  */
  28 #define MCFSIM_RSR              0x00            /* Reset Status reg (r/w) */
  29 #define MCFSIM_SYPCR            0x01            /* System Protection reg (r/w)*/
  30 #define MCFSIM_SWIVR            0x02            /* SW Watchdog intr reg (r/w) */
  31 #define MCFSIM_SWSR             0x03            /* SW Watchdog service (r/w) */
  32 #define MCFSIM_PAR              0x04            /* Pin Assignment reg (r/w) */
  33 #define MCFSIM_IRQPAR           0x06            /* Interrupt Assignment reg (r/w) */
  34 #define MCFSIM_MPARK            0x0C            /* BUS Master Control Reg*/
  35 #define MCFSIM_IPR              0x40            /* Interrupt Pend reg (r/w) */
  36 #define MCFSIM_IMR              0x44            /* Interrupt Mask reg (r/w) */
  37 #define MCFSIM_AVR              0x4b            /* Autovector Ctrl reg (r/w) */
  38 #define MCFSIM_ICR0             0x4c            /* Intr Ctrl reg 0 (r/w) */
  39 #define MCFSIM_ICR1             0x4d            /* Intr Ctrl reg 1 (r/w) */
  40 #define MCFSIM_ICR2             0x4e            /* Intr Ctrl reg 2 (r/w) */
  41 #define MCFSIM_ICR3             0x4f            /* Intr Ctrl reg 3 (r/w) */
  42 #define MCFSIM_ICR4             0x50            /* Intr Ctrl reg 4 (r/w) */
  43 #define MCFSIM_ICR5             0x51            /* Intr Ctrl reg 5 (r/w) */
  44 #define MCFSIM_ICR6             0x52            /* Intr Ctrl reg 6 (r/w) */
  45 #define MCFSIM_ICR7             0x53            /* Intr Ctrl reg 7 (r/w) */
  46 #define MCFSIM_ICR8             0x54            /* Intr Ctrl reg 8 (r/w) */
  47 #define MCFSIM_ICR9             0x55            /* Intr Ctrl reg 9 (r/w) */
  48 #define MCFSIM_ICR10            0x56            /* Intr Ctrl reg 10 (r/w) */
  49 #define MCFSIM_ICR11            0x57            /* Intr Ctrl reg 11 (r/w) */
  50
  51 #define MCFSIM_CSAR0            0x80            /* CS 0 Address 0 reg (r/w) */
  52 #define MCFSIM_CSMR0            0x84            /* CS 0 Mask 0 reg (r/w) */
  53 #define MCFSIM_CSCR0            0x8a            /* CS 0 Control reg (r/w) */
  54 #define MCFSIM_CSAR1            0x8c            /* CS 1 Address reg (r/w) */
  55 #define MCFSIM_CSMR1            0x90            /* CS 1 Mask reg (r/w) */
  56 #define MCFSIM_CSCR1            0x96            /* CS 1 Control reg (r/w) */
  57 #define MCFSIM_CSAR2            0x98            /* CS 2 Address reg (r/w) */
  58 #define MCFSIM_CSMR2            0x9c            /* CS 2 Mask reg (r/w) */
  59 #define MCFSIM_CSCR2            0xa2            /* CS 2 Control reg (r/w) */
  60 #define MCFSIM_CSAR3            0xa4            /* CS 3 Address reg (r/w) */
  61 #define MCFSIM_CSMR3            0xa8            /* CS 3 Mask reg (r/w) */
  62 #define MCFSIM_CSCR3            0xae            /* CS 3 Control reg (r/w) */
  63
  64 #define MCFSIM_DCR              (MCF_MBAR + 0x100)      /* DRAM Control */
  65 #define MCFSIM_DACR0            (MCF_MBAR + 0x108)      /* DRAM 0 Addr/Ctrl */
  66 #define MCFSIM_DMR0             (MCF_MBAR + 0x10c)      /* DRAM 0 Mask */
  67 #define MCFSIM_DACR1            (MCF_MBAR + 0x110)      /* DRAM 1 Addr/Ctrl */
  68 #define MCFSIM_DMR1             (MCF_MBAR + 0x114)      /* DRAM 1 Mask */
  69
  70 /*
  71  *      Timer module.
  72  */
  73 #define MCFTIMER_BASE1          (MCF_MBAR + 0x140)      /* Base of TIMER1 */
  74 #define MCFTIMER_BASE2          (MCF_MBAR + 0x180)      /* Base of TIMER2 */
  75
  76 /*
  77  *      UART module.
  78  */
  79 #define MCFUART_BASE0           (MCF_MBAR + 0x1c0)      /* Base address UART0 */
  80 #define MCFUART_BASE1           (MCF_MBAR + 0x200)      /* Base address UART1 */
  81
  82 /*
  83  *      QSPI module.
  84  */
  85 #define MCFQSPI_BASE            (MCF_MBAR + 0x300)      /* Base address QSPI */
  86 #define MCFQSPI_SIZE            0x40                    /* Register set size */
  87
  88 #define MCFQSPI_CS0             29
  89 #define MCFQSPI_CS1             24
  90 #define MCFQSPI_CS2             21
  91 #define MCFQSPI_CS3             22
  92
  93 /*
  94  *      DMA unit base addresses.
  95  */
  96 #define MCFDMA_BASE0            (MCF_MBAR + 0x300)      /* Base address DMA 0 */
  97 #define MCFDMA_BASE1            (MCF_MBAR + 0x340)      /* Base address DMA 1 */
  98 #define MCFDMA_BASE2            (MCF_MBAR + 0x380)      /* Base address DMA 2 */
  99 #define MCFDMA_BASE3            (MCF_MBAR + 0x3C0)      /* Base address DMA 3 */
 100
 101 /*
 102  *      Some symbol defines for the above...
 103  */
 104 #define MCFSIM_SWDICR           MCFSIM_ICR0     /* Watchdog timer ICR */
 105 #define MCFSIM_TIMER1ICR        MCFSIM_ICR1     /* Timer 1 ICR */
 106 #define MCFSIM_TIMER2ICR        MCFSIM_ICR2     /* Timer 2 ICR */
 107 #define MCFSIM_UART1ICR         MCFSIM_ICR4     /* UART 1 ICR */
 108 #define MCFSIM_UART2ICR         MCFSIM_ICR5     /* UART 2 ICR */
 109 #define MCFSIM_DMA0ICR          MCFSIM_ICR6     /* DMA 0 ICR */
 110 #define MCFSIM_DMA1ICR          MCFSIM_ICR7     /* DMA 1 ICR */
 111 #define MCFSIM_DMA2ICR          MCFSIM_ICR8     /* DMA 2 ICR */
 112 #define MCFSIM_DMA3ICR          MCFSIM_ICR9     /* DMA 3 ICR */
 113 #define MCFSIM_QSPIICR          MCFSIM_ICR10    /* QSPI ICR */
 114
 115 /*
 116  *      Define system peripheral IRQ usage.
 117  */
 118 #define MCF_IRQ_QSPI            28              /* QSPI, Level 4 */
 119 #define MCF_IRQ_TIMER           30              /* Timer0, Level 6 */
 120 #define MCF_IRQ_PROFILER        31              /* Timer1, Level 7 */
 121
 122 #define MCF_IRQ_UART0           73              /* UART0 */
 123 #define MCF_IRQ_UART1           74              /* UART1 */
 124
 125 /*
 126  *      General purpose IO registers (in MBAR2).
 127  */
 128 #define MCFSIM2_GPIOREAD        (MCF_MBAR2 + 0x000)     /* GPIO read values */
 129 #define MCFSIM2_GPIOWRITE       (MCF_MBAR2 + 0x004)     /* GPIO write values */
 130 #define MCFSIM2_GPIOENABLE      (MCF_MBAR2 + 0x008)     /* GPIO enabled */
 131 #define MCFSIM2_GPIOFUNC        (MCF_MBAR2 + 0x00C)     /* GPIO function */
 132 #define MCFSIM2_GPIO1READ       (MCF_MBAR2 + 0x0B0)     /* GPIO1 read values */
 133 #define MCFSIM2_GPIO1WRITE      (MCF_MBAR2 + 0x0B4)     /* GPIO1 write values */
 134 #define MCFSIM2_GPIO1ENABLE     (MCF_MBAR2 + 0x0B8)     /* GPIO1 enabled */
 135 #define MCFSIM2_GPIO1FUNC       (MCF_MBAR2 + 0x0BC)     /* GPIO1 function */
 136
 137 #define MCFSIM2_GPIOINTSTAT     0xc0            /* GPIO interrupt status */
 138 #define MCFSIM2_GPIOINTCLEAR    0xc0            /* GPIO interrupt clear */
 139 #define MCFSIM2_GPIOINTENABLE   0xc4            /* GPIO interrupt enable */
 140
 141 #define MCFSIM2_INTLEVEL1       0x140           /* Interrupt level reg 1 */
 142 #define MCFSIM2_INTLEVEL2       0x144           /* Interrupt level reg 2 */
 143 #define MCFSIM2_INTLEVEL3       0x148           /* Interrupt level reg 3 */
 144 #define MCFSIM2_INTLEVEL4       0x14c           /* Interrupt level reg 4 */
 145 #define MCFSIM2_INTLEVEL5       0x150           /* Interrupt level reg 5 */
 146 #define MCFSIM2_INTLEVEL6       0x154           /* Interrupt level reg 6 */
 147 #define MCFSIM2_INTLEVEL7       0x158           /* Interrupt level reg 7 */
 148 #define MCFSIM2_INTLEVEL8       0x15c           /* Interrupt level reg 8 */
 149
 150 #define MCFSIM2_DMAROUTE        0x188           /* DMA routing */
 151
 152 #define MCFSIM2_IDECONFIG1      0x18c           /* IDEconfig1 */
 153 #define MCFSIM2_IDECONFIG2      0x190           /* IDEconfig2 */
 154
 155 /*
 156  * Define the base interrupt for the second interrupt controller.
 157  * We set it to 128, out of the way of the base interrupts, and plenty
 158  * of room for its 64 interrupts.
 159  */
 160 #define MCFINTC2_VECBASE        128
 161
 162 #define MCFINTC2_GPIOIRQ0       (MCFINTC2_VECBASE + 32)
 163 #define MCFINTC2_GPIOIRQ1       (MCFINTC2_VECBASE + 33)
 164 #define MCFINTC2_GPIOIRQ2       (MCFINTC2_VECBASE + 34)
 165 #define MCFINTC2_GPIOIRQ3       (MCFINTC2_VECBASE + 35)
 166 #define MCFINTC2_GPIOIRQ4       (MCFINTC2_VECBASE + 36)
 167 #define MCFINTC2_GPIOIRQ5       (MCFINTC2_VECBASE + 37)
 168 #define MCFINTC2_GPIOIRQ6       (MCFINTC2_VECBASE + 38)
 169 #define MCFINTC2_GPIOIRQ7       (MCFINTC2_VECBASE + 39)
 170
 171 /*
 172  * Generic GPIO support
 173  */
 174 #define MCFGPIO_PIN_MAX         64
 175 #define MCFGPIO_IRQ_MAX         -1
 176 #define MCFGPIO_IRQ_VECBASE     -1
 177
 178 /****************************************************************************/
 179
 180 #ifdef __ASSEMBLER__
 181
 182 /*
 183  *      The M5249C3 board needs a little help getting all its SIM devices
 184  *      initialized at kernel start time. dBUG doesn't set much up, so
 185  *      we need to do it manually.
 186  */
 187 .macro m5249c3_setup
 188         /*
 189          *      Set MBAR1 and MBAR2, just incase they are not set.
 190          */
 191         movel   #0x10000001,%a0
 192         movec   %a0,%MBAR                       /* map MBAR region */
 193         subql   #1,%a0                          /* get MBAR address in a0 */
 194
 195         movel   #0x80000001,%a1
 196         movec   %a1,#3086                       /* map MBAR2 region */
 197         subql   #1,%a1                          /* get MBAR2 address in a1 */
 198
 199         /*
 200          *      Move secondary interrupts to their base (128).
 201          */
 202         moveb   #MCFINTC2_VECBASE,%d0
 203         moveb   %d0,0x16b(%a1)                  /* interrupt base register */
 204
 205         /*
 206          *      Work around broken CSMR0/DRAM vector problem.
 207          */
 208         movel   #0x001F0021,%d0                 /* disable C/I bit */
 209         movel   %d0,0x84(%a0)                   /* set CSMR0 */
 210
 211         /*
 212          *      Disable the PLL firstly. (Who knows what state it is
 213          *      in here!).
 214          */
 215         movel   0x180(%a1),%d0                  /* get current PLL value */
 216         andl    #0xfffffffe,%d0                 /* PLL bypass first */
 217         movel   %d0,0x180(%a1)                  /* set PLL register */
 218         nop
 219
 220 #if CONFIG_CLOCK_FREQ == 140000000
 221         /*
 222          *      Set initial clock frequency. This assumes M5249C3 board
 223          *      is fitted with 11.2896MHz crystal. It will program the
 224          *      PLL for 140MHz. Lets go fast :-)
 225          */
 226         movel   #0x125a40f0,%d0                 /* set for 140MHz */
 227         movel   %d0,0x180(%a1)                  /* set PLL register */
 228         orl     #0x1,%d0
 229         movel   %d0,0x180(%a1)                  /* set PLL register */
 230 #endif
 231
 232         /*
 233          *      Setup CS1 for ethernet controller.
 234          *      (Setup as per M5249C3 doco).
 235          */
 236         movel  #0xe0000000,%d0                  /* CS1 mapped at 0xe0000000 */
 237         movel  %d0,0x8c(%a0)
 238         movel  #0x001f0021,%d0                  /* CS1 size of 1Mb */
 239         movel  %d0,0x90(%a0)
 240         movew  #0x0080,%d0                      /* CS1 = 16bit port, AA */
 241         movew  %d0,0x96(%a0)
 242
 243         /*
 244          *      Setup CS2 for IDE interface.
 245          */
 246         movel   #0x50000000,%d0                 /* CS2 mapped at 0x50000000 */
 247         movel   %d0,0x98(%a0)
 248         movel   #0x001f0001,%d0                 /* CS2 size of 1MB */
 249         movel   %d0,0x9c(%a0)
 250         movew   #0x0080,%d0                     /* CS2 = 16bit, TA */
 251         movew   %d0,0xa2(%a0)
 252
 253         movel   #0x00107000,%d0                 /* IDEconfig1 */
 254         movel   %d0,0x18c(%a1)
 255         movel   #0x000c0400,%d0                 /* IDEconfig2 */
 256         movel   %d0,0x190(%a1)
 257
 258         movel   #0x00080000,%d0                 /* GPIO19, IDE reset bit */
 259         orl     %d0,0xc(%a1)                    /* function GPIO19 */
 260         orl     %d0,0x8(%a1)                    /* enable GPIO19 as output */
 261         orl     %d0,0x4(%a1)                    /* de-assert IDE reset */
 262 .endm
 263
 264 #define PLATFORM_SETUP  m5249c3_setup
 265
 266 #endif /* __ASSEMBLER__ */
 267
 268 /****************************************************************************/
 269 #endif  /* m5249sim_h */