2 * linux/drivers/mmc/host/mxcmmc.c - Freescale i.MX MMCI driver
4 * This is a driver for the SDHC controller found in Freescale MX2/MX3
5 * SoCs. It is basically the same hardware as found on MX1 (imxmmc.c).
6 * Unlike the hardware found on MX1, this hardware just works and does
7 * not need all the quirks found in imxmmc.c, hence the separate driver.
9 * Copyright (C) 2008 Sascha Hauer, Pengutronix <s.hauer@pengutronix.de>
10 * Copyright (C) 2006 Pavel Pisa, PiKRON <ppisa@pikron.com>
12 * derived from pxamci.c by Russell King
14 * This program is free software; you can redistribute it and/or modify
15 * it under the terms of the GNU General Public License version 2 as
16 * published by the Free Software Foundation.
20 #include <linux/module.h>
21 #include <linux/init.h>
22 #include <linux/ioport.h>
23 #include <linux/platform_device.h>
24 #include <linux/interrupt.h>
25 #include <linux/irq.h>
26 #include <linux/blkdev.h>
27 #include <linux/dma-mapping.h>
28 #include <linux/mmc/host.h>
29 #include <linux/mmc/card.h>
30 #include <linux/delay.h>
31 #include <linux/clk.h>
33 #include <linux/gpio.h>
34 #include <linux/regulator/consumer.h>
35 #include <linux/dmaengine.h>
36 #include <linux/types.h>
40 #include <asm/sizes.h>
44 #include <mach/hardware.h>
46 #define DRIVER_NAME "mxc-mmc"
48 #define MMC_REG_STR_STP_CLK 0x00
49 #define MMC_REG_STATUS 0x04
50 #define MMC_REG_CLK_RATE 0x08
51 #define MMC_REG_CMD_DAT_CONT 0x0C
52 #define MMC_REG_RES_TO 0x10
53 #define MMC_REG_READ_TO 0x14
54 #define MMC_REG_BLK_LEN 0x18
55 #define MMC_REG_NOB 0x1C
56 #define MMC_REG_REV_NO 0x20
57 #define MMC_REG_INT_CNTR 0x24
58 #define MMC_REG_CMD 0x28
59 #define MMC_REG_ARG 0x2C
60 #define MMC_REG_RES_FIFO 0x34
61 #define MMC_REG_BUFFER_ACCESS 0x38
63 #define STR_STP_CLK_RESET (1 << 3)
64 #define STR_STP_CLK_START_CLK (1 << 1)
65 #define STR_STP_CLK_STOP_CLK (1 << 0)
67 #define STATUS_CARD_INSERTION (1 << 31)
68 #define STATUS_CARD_REMOVAL (1 << 30)
69 #define STATUS_YBUF_EMPTY (1 << 29)
70 #define STATUS_XBUF_EMPTY (1 << 28)
71 #define STATUS_YBUF_FULL (1 << 27)
72 #define STATUS_XBUF_FULL (1 << 26)
73 #define STATUS_BUF_UND_RUN (1 << 25)
74 #define STATUS_BUF_OVFL (1 << 24)
75 #define STATUS_SDIO_INT_ACTIVE (1 << 14)
76 #define STATUS_END_CMD_RESP (1 << 13)
77 #define STATUS_WRITE_OP_DONE (1 << 12)
78 #define STATUS_DATA_TRANS_DONE (1 << 11)
79 #define STATUS_READ_OP_DONE (1 << 11)
80 #define STATUS_WR_CRC_ERROR_CODE_MASK (3 << 10)
81 #define STATUS_CARD_BUS_CLK_RUN (1 << 8)
82 #define STATUS_BUF_READ_RDY (1 << 7)
83 #define STATUS_BUF_WRITE_RDY (1 << 6)
84 #define STATUS_RESP_CRC_ERR (1 << 5)
85 #define STATUS_CRC_READ_ERR (1 << 3)
86 #define STATUS_CRC_WRITE_ERR (1 << 2)
87 #define STATUS_TIME_OUT_RESP (1 << 1)
88 #define STATUS_TIME_OUT_READ (1 << 0)
89 #define STATUS_ERR_MASK 0x2f
91 #define CMD_DAT_CONT_CMD_RESP_LONG_OFF (1 << 12)
92 #define CMD_DAT_CONT_STOP_READWAIT (1 << 11)
93 #define CMD_DAT_CONT_START_READWAIT (1 << 10)
94 #define CMD_DAT_CONT_BUS_WIDTH_4 (2 << 8)
95 #define CMD_DAT_CONT_INIT (1 << 7)
96 #define CMD_DAT_CONT_WRITE (1 << 4)
97 #define CMD_DAT_CONT_DATA_ENABLE (1 << 3)
98 #define CMD_DAT_CONT_RESPONSE_48BIT_CRC (1 << 0)
99 #define CMD_DAT_CONT_RESPONSE_136BIT (2 << 0)
100 #define CMD_DAT_CONT_RESPONSE_48BIT (3 << 0)
102 #define INT_SDIO_INT_WKP_EN (1 << 18)
103 #define INT_CARD_INSERTION_WKP_EN (1 << 17)
104 #define INT_CARD_REMOVAL_WKP_EN (1 << 16)
105 #define INT_CARD_INSERTION_EN (1 << 15)
106 #define INT_CARD_REMOVAL_EN (1 << 14)
107 #define INT_SDIO_IRQ_EN (1 << 13)
108 #define INT_DAT0_EN (1 << 12)
109 #define INT_BUF_READ_EN (1 << 4)
110 #define INT_BUF_WRITE_EN (1 << 3)
111 #define INT_END_CMD_RES_EN (1 << 2)
112 #define INT_WRITE_OP_DONE_EN (1 << 1)
113 #define INT_READ_OP_EN (1 << 0)
116 struct mmc_host
*mmc
;
117 struct resource
*res
;
121 struct dma_chan
*dma
;
122 struct dma_async_tx_descriptor
*desc
;
124 int default_irq_mask
;
126 unsigned int power_mode
;
127 struct imxmmc_platform_data
*pdata
;
129 struct mmc_request
*req
;
130 struct mmc_command
*cmd
;
131 struct mmc_data
*data
;
133 unsigned int datasize
;
134 unsigned int dma_dir
;
144 struct work_struct datawork
;
147 struct regulator
*vcc
;
151 struct dma_slave_config dma_slave_config
;
152 struct imx_dma_data dma_data
;
155 static void mxcmci_set_clk_rate(struct mxcmci_host
*host
, unsigned int clk_ios
);
157 static inline void mxcmci_init_ocr(struct mxcmci_host
*host
)
159 host
->vcc
= regulator_get(mmc_dev(host
->mmc
), "vmmc");
161 if (IS_ERR(host
->vcc
)) {
164 host
->mmc
->ocr_avail
= mmc_regulator_get_ocrmask(host
->vcc
);
165 if (host
->pdata
&& host
->pdata
->ocr_avail
)
166 dev_warn(mmc_dev(host
->mmc
),
167 "pdata->ocr_avail will not be used\n");
170 if (host
->vcc
== NULL
) {
171 /* fall-back to platform data */
172 if (host
->pdata
&& host
->pdata
->ocr_avail
)
173 host
->mmc
->ocr_avail
= host
->pdata
->ocr_avail
;
175 host
->mmc
->ocr_avail
= MMC_VDD_32_33
| MMC_VDD_33_34
;
179 static inline void mxcmci_set_power(struct mxcmci_host
*host
,
180 unsigned char power_mode
,
184 if (power_mode
== MMC_POWER_UP
)
185 mmc_regulator_set_ocr(host
->mmc
, host
->vcc
, vdd
);
186 else if (power_mode
== MMC_POWER_OFF
)
187 mmc_regulator_set_ocr(host
->mmc
, host
->vcc
, 0);
190 if (host
->pdata
&& host
->pdata
->setpower
)
191 host
->pdata
->setpower(mmc_dev(host
->mmc
), vdd
);
194 static inline int mxcmci_use_dma(struct mxcmci_host
*host
)
199 static void mxcmci_softreset(struct mxcmci_host
*host
)
203 dev_dbg(mmc_dev(host
->mmc
), "mxcmci_softreset\n");
206 writew(STR_STP_CLK_RESET
, host
->base
+ MMC_REG_STR_STP_CLK
);
207 writew(STR_STP_CLK_RESET
| STR_STP_CLK_START_CLK
,
208 host
->base
+ MMC_REG_STR_STP_CLK
);
210 for (i
= 0; i
< 8; i
++)
211 writew(STR_STP_CLK_START_CLK
, host
->base
+ MMC_REG_STR_STP_CLK
);
213 writew(0xff, host
->base
+ MMC_REG_RES_TO
);
215 static int mxcmci_setup_dma(struct mmc_host
*mmc
);
217 static int mxcmci_setup_data(struct mxcmci_host
*host
, struct mmc_data
*data
)
219 unsigned int nob
= data
->blocks
;
220 unsigned int blksz
= data
->blksz
;
221 unsigned int datasize
= nob
* blksz
;
222 struct scatterlist
*sg
;
223 enum dma_transfer_direction slave_dirn
;
226 if (data
->flags
& MMC_DATA_STREAM
)
230 data
->bytes_xfered
= 0;
232 writew(nob
, host
->base
+ MMC_REG_NOB
);
233 writew(blksz
, host
->base
+ MMC_REG_BLK_LEN
);
234 host
->datasize
= datasize
;
236 if (!mxcmci_use_dma(host
))
239 for_each_sg(data
->sg
, sg
, data
->sg_len
, i
) {
240 if (sg
->offset
& 3 || sg
->length
& 3) {
246 if (data
->flags
& MMC_DATA_READ
) {
247 host
->dma_dir
= DMA_FROM_DEVICE
;
248 slave_dirn
= DMA_DEV_TO_MEM
;
250 host
->dma_dir
= DMA_TO_DEVICE
;
251 slave_dirn
= DMA_MEM_TO_DEV
;
254 nents
= dma_map_sg(host
->dma
->device
->dev
, data
->sg
,
255 data
->sg_len
, host
->dma_dir
);
256 if (nents
!= data
->sg_len
)
259 host
->desc
= dmaengine_prep_slave_sg(host
->dma
,
260 data
->sg
, data
->sg_len
, slave_dirn
,
261 DMA_PREP_INTERRUPT
| DMA_CTRL_ACK
);
264 dma_unmap_sg(host
->dma
->device
->dev
, data
->sg
, data
->sg_len
,
267 return 0; /* Fall back to PIO */
271 dmaengine_submit(host
->desc
);
272 dma_async_issue_pending(host
->dma
);
277 static int mxcmci_start_cmd(struct mxcmci_host
*host
, struct mmc_command
*cmd
,
280 u32 int_cntr
= host
->default_irq_mask
;
283 WARN_ON(host
->cmd
!= NULL
);
286 switch (mmc_resp_type(cmd
)) {
287 case MMC_RSP_R1
: /* short CRC, OPCODE */
288 case MMC_RSP_R1B
:/* short CRC, OPCODE, BUSY */
289 cmdat
|= CMD_DAT_CONT_RESPONSE_48BIT_CRC
;
291 case MMC_RSP_R2
: /* long 136 bit + CRC */
292 cmdat
|= CMD_DAT_CONT_RESPONSE_136BIT
;
294 case MMC_RSP_R3
: /* short */
295 cmdat
|= CMD_DAT_CONT_RESPONSE_48BIT
;
300 dev_err(mmc_dev(host
->mmc
), "unhandled response type 0x%x\n",
302 cmd
->error
= -EINVAL
;
306 int_cntr
= INT_END_CMD_RES_EN
;
308 if (mxcmci_use_dma(host
))
309 int_cntr
|= INT_READ_OP_EN
| INT_WRITE_OP_DONE_EN
;
311 spin_lock_irqsave(&host
->lock
, flags
);
313 int_cntr
|= INT_SDIO_IRQ_EN
;
314 writel(int_cntr
, host
->base
+ MMC_REG_INT_CNTR
);
315 spin_unlock_irqrestore(&host
->lock
, flags
);
317 writew(cmd
->opcode
, host
->base
+ MMC_REG_CMD
);
318 writel(cmd
->arg
, host
->base
+ MMC_REG_ARG
);
319 writew(cmdat
, host
->base
+ MMC_REG_CMD_DAT_CONT
);
324 static void mxcmci_finish_request(struct mxcmci_host
*host
,
325 struct mmc_request
*req
)
327 u32 int_cntr
= host
->default_irq_mask
;
330 spin_lock_irqsave(&host
->lock
, flags
);
332 int_cntr
|= INT_SDIO_IRQ_EN
;
333 writel(int_cntr
, host
->base
+ MMC_REG_INT_CNTR
);
334 spin_unlock_irqrestore(&host
->lock
, flags
);
340 mmc_request_done(host
->mmc
, req
);
343 static int mxcmci_finish_data(struct mxcmci_host
*host
, unsigned int stat
)
345 struct mmc_data
*data
= host
->data
;
348 if (mxcmci_use_dma(host
)) {
349 dmaengine_terminate_all(host
->dma
);
350 dma_unmap_sg(host
->dma
->device
->dev
, data
->sg
, data
->sg_len
,
354 if (stat
& STATUS_ERR_MASK
) {
355 dev_dbg(mmc_dev(host
->mmc
), "request failed. status: 0x%08x\n",
357 if (stat
& STATUS_CRC_READ_ERR
) {
358 dev_err(mmc_dev(host
->mmc
), "%s: -EILSEQ\n", __func__
);
359 data
->error
= -EILSEQ
;
360 } else if (stat
& STATUS_CRC_WRITE_ERR
) {
361 u32 err_code
= (stat
>> 9) & 0x3;
362 if (err_code
== 2) { /* No CRC response */
363 dev_err(mmc_dev(host
->mmc
),
364 "%s: No CRC -ETIMEDOUT\n", __func__
);
365 data
->error
= -ETIMEDOUT
;
367 dev_err(mmc_dev(host
->mmc
),
368 "%s: -EILSEQ\n", __func__
);
369 data
->error
= -EILSEQ
;
371 } else if (stat
& STATUS_TIME_OUT_READ
) {
372 dev_err(mmc_dev(host
->mmc
),
373 "%s: read -ETIMEDOUT\n", __func__
);
374 data
->error
= -ETIMEDOUT
;
376 dev_err(mmc_dev(host
->mmc
), "%s: -EIO\n", __func__
);
380 data
->bytes_xfered
= host
->datasize
;
383 data_error
= data
->error
;
390 static void mxcmci_read_response(struct mxcmci_host
*host
, unsigned int stat
)
392 struct mmc_command
*cmd
= host
->cmd
;
399 if (stat
& STATUS_TIME_OUT_RESP
) {
400 dev_dbg(mmc_dev(host
->mmc
), "CMD TIMEOUT\n");
401 cmd
->error
= -ETIMEDOUT
;
402 } else if (stat
& STATUS_RESP_CRC_ERR
&& cmd
->flags
& MMC_RSP_CRC
) {
403 dev_dbg(mmc_dev(host
->mmc
), "cmd crc error\n");
404 cmd
->error
= -EILSEQ
;
407 if (cmd
->flags
& MMC_RSP_PRESENT
) {
408 if (cmd
->flags
& MMC_RSP_136
) {
409 for (i
= 0; i
< 4; i
++) {
410 a
= readw(host
->base
+ MMC_REG_RES_FIFO
);
411 b
= readw(host
->base
+ MMC_REG_RES_FIFO
);
412 cmd
->resp
[i
] = a
<< 16 | b
;
415 a
= readw(host
->base
+ MMC_REG_RES_FIFO
);
416 b
= readw(host
->base
+ MMC_REG_RES_FIFO
);
417 c
= readw(host
->base
+ MMC_REG_RES_FIFO
);
418 cmd
->resp
[0] = a
<< 24 | b
<< 8 | c
>> 8;
423 static int mxcmci_poll_status(struct mxcmci_host
*host
, u32 mask
)
426 unsigned long timeout
= jiffies
+ HZ
;
429 stat
= readl(host
->base
+ MMC_REG_STATUS
);
430 if (stat
& STATUS_ERR_MASK
)
432 if (time_after(jiffies
, timeout
)) {
433 mxcmci_softreset(host
);
434 mxcmci_set_clk_rate(host
, host
->clock
);
435 return STATUS_TIME_OUT_READ
;
443 static int mxcmci_pull(struct mxcmci_host
*host
, void *_buf
, int bytes
)
449 stat
= mxcmci_poll_status(host
,
450 STATUS_BUF_READ_RDY
| STATUS_READ_OP_DONE
);
453 *buf
++ = readl(host
->base
+ MMC_REG_BUFFER_ACCESS
);
461 stat
= mxcmci_poll_status(host
,
462 STATUS_BUF_READ_RDY
| STATUS_READ_OP_DONE
);
465 tmp
= readl(host
->base
+ MMC_REG_BUFFER_ACCESS
);
466 memcpy(b
, &tmp
, bytes
);
472 static int mxcmci_push(struct mxcmci_host
*host
, void *_buf
, int bytes
)
478 stat
= mxcmci_poll_status(host
, STATUS_BUF_WRITE_RDY
);
481 writel(*buf
++, host
->base
+ MMC_REG_BUFFER_ACCESS
);
489 stat
= mxcmci_poll_status(host
, STATUS_BUF_WRITE_RDY
);
493 memcpy(&tmp
, b
, bytes
);
494 writel(tmp
, host
->base
+ MMC_REG_BUFFER_ACCESS
);
497 stat
= mxcmci_poll_status(host
, STATUS_BUF_WRITE_RDY
);
504 static int mxcmci_transfer_data(struct mxcmci_host
*host
)
506 struct mmc_data
*data
= host
->req
->data
;
507 struct scatterlist
*sg
;
513 if (data
->flags
& MMC_DATA_READ
) {
514 for_each_sg(data
->sg
, sg
, data
->sg_len
, i
) {
515 stat
= mxcmci_pull(host
, sg_virt(sg
), sg
->length
);
518 host
->datasize
+= sg
->length
;
521 for_each_sg(data
->sg
, sg
, data
->sg_len
, i
) {
522 stat
= mxcmci_push(host
, sg_virt(sg
), sg
->length
);
525 host
->datasize
+= sg
->length
;
527 stat
= mxcmci_poll_status(host
, STATUS_WRITE_OP_DONE
);
534 static void mxcmci_datawork(struct work_struct
*work
)
536 struct mxcmci_host
*host
= container_of(work
, struct mxcmci_host
,
538 int datastat
= mxcmci_transfer_data(host
);
540 writel(STATUS_READ_OP_DONE
| STATUS_WRITE_OP_DONE
,
541 host
->base
+ MMC_REG_STATUS
);
542 mxcmci_finish_data(host
, datastat
);
544 if (host
->req
->stop
) {
545 if (mxcmci_start_cmd(host
, host
->req
->stop
, 0)) {
546 mxcmci_finish_request(host
, host
->req
);
550 mxcmci_finish_request(host
, host
->req
);
554 static void mxcmci_data_done(struct mxcmci_host
*host
, unsigned int stat
)
556 struct mmc_data
*data
= host
->data
;
562 data_error
= mxcmci_finish_data(host
, stat
);
564 mxcmci_read_response(host
, stat
);
567 if (host
->req
->stop
) {
568 if (mxcmci_start_cmd(host
, host
->req
->stop
, 0)) {
569 mxcmci_finish_request(host
, host
->req
);
573 mxcmci_finish_request(host
, host
->req
);
577 static void mxcmci_cmd_done(struct mxcmci_host
*host
, unsigned int stat
)
579 mxcmci_read_response(host
, stat
);
582 if (!host
->data
&& host
->req
) {
583 mxcmci_finish_request(host
, host
->req
);
587 /* For the DMA case the DMA engine handles the data transfer
588 * automatically. For non DMA we have to do it ourselves.
589 * Don't do it in interrupt context though.
591 if (!mxcmci_use_dma(host
) && host
->data
)
592 schedule_work(&host
->datawork
);
596 static irqreturn_t
mxcmci_irq(int irq
, void *devid
)
598 struct mxcmci_host
*host
= devid
;
603 stat
= readl(host
->base
+ MMC_REG_STATUS
);
604 writel(stat
& ~(STATUS_SDIO_INT_ACTIVE
| STATUS_DATA_TRANS_DONE
|
605 STATUS_WRITE_OP_DONE
), host
->base
+ MMC_REG_STATUS
);
607 dev_dbg(mmc_dev(host
->mmc
), "%s: 0x%08x\n", __func__
, stat
);
609 spin_lock_irqsave(&host
->lock
, flags
);
610 sdio_irq
= (stat
& STATUS_SDIO_INT_ACTIVE
) && host
->use_sdio
;
611 spin_unlock_irqrestore(&host
->lock
, flags
);
613 if (mxcmci_use_dma(host
) &&
614 (stat
& (STATUS_READ_OP_DONE
| STATUS_WRITE_OP_DONE
)))
615 writel(STATUS_READ_OP_DONE
| STATUS_WRITE_OP_DONE
,
616 host
->base
+ MMC_REG_STATUS
);
619 writel(STATUS_SDIO_INT_ACTIVE
, host
->base
+ MMC_REG_STATUS
);
620 mmc_signal_sdio_irq(host
->mmc
);
623 if (stat
& STATUS_END_CMD_RESP
)
624 mxcmci_cmd_done(host
, stat
);
626 if (mxcmci_use_dma(host
) &&
627 (stat
& (STATUS_DATA_TRANS_DONE
| STATUS_WRITE_OP_DONE
)))
628 mxcmci_data_done(host
, stat
);
630 if (host
->default_irq_mask
&&
631 (stat
& (STATUS_CARD_INSERTION
| STATUS_CARD_REMOVAL
)))
632 mmc_detect_change(host
->mmc
, msecs_to_jiffies(200));
637 static void mxcmci_request(struct mmc_host
*mmc
, struct mmc_request
*req
)
639 struct mxcmci_host
*host
= mmc_priv(mmc
);
640 unsigned int cmdat
= host
->cmdat
;
643 WARN_ON(host
->req
!= NULL
);
646 host
->cmdat
&= ~CMD_DAT_CONT_INIT
;
652 error
= mxcmci_setup_data(host
, req
->data
);
654 req
->cmd
->error
= error
;
659 cmdat
|= CMD_DAT_CONT_DATA_ENABLE
;
661 if (req
->data
->flags
& MMC_DATA_WRITE
)
662 cmdat
|= CMD_DAT_CONT_WRITE
;
665 error
= mxcmci_start_cmd(host
, req
->cmd
, cmdat
);
669 mxcmci_finish_request(host
, req
);
672 static void mxcmci_set_clk_rate(struct mxcmci_host
*host
, unsigned int clk_ios
)
674 unsigned int divider
;
676 unsigned int clk_in
= clk_get_rate(host
->clk_per
);
678 while (prescaler
<= 0x800) {
679 for (divider
= 1; divider
<= 0xF; divider
++) {
682 x
= (clk_in
/ (divider
+ 1));
685 x
/= (prescaler
* 2);
699 writew((prescaler
<< 4) | divider
, host
->base
+ MMC_REG_CLK_RATE
);
701 dev_dbg(mmc_dev(host
->mmc
), "scaler: %d divider: %d in: %d out: %d\n",
702 prescaler
, divider
, clk_in
, clk_ios
);
705 static int mxcmci_setup_dma(struct mmc_host
*mmc
)
707 struct mxcmci_host
*host
= mmc_priv(mmc
);
708 struct dma_slave_config
*config
= &host
->dma_slave_config
;
710 config
->dst_addr
= host
->res
->start
+ MMC_REG_BUFFER_ACCESS
;
711 config
->src_addr
= host
->res
->start
+ MMC_REG_BUFFER_ACCESS
;
712 config
->dst_addr_width
= 4;
713 config
->src_addr_width
= 4;
714 config
->dst_maxburst
= host
->burstlen
;
715 config
->src_maxburst
= host
->burstlen
;
716 config
->device_fc
= false;
718 return dmaengine_slave_config(host
->dma
, config
);
721 static void mxcmci_set_ios(struct mmc_host
*mmc
, struct mmc_ios
*ios
)
723 struct mxcmci_host
*host
= mmc_priv(mmc
);
727 * use burstlen of 64 (16 words) in 4 bit mode (--> reg value 0)
728 * use burstlen of 16 (4 words) in 1 bit mode (--> reg value 16)
730 if (ios
->bus_width
== MMC_BUS_WIDTH_4
)
735 if (mxcmci_use_dma(host
) && burstlen
!= host
->burstlen
) {
736 host
->burstlen
= burstlen
;
737 ret
= mxcmci_setup_dma(mmc
);
739 dev_err(mmc_dev(host
->mmc
),
740 "failed to config DMA channel. Falling back to PIO\n");
741 dma_release_channel(host
->dma
);
747 if (ios
->bus_width
== MMC_BUS_WIDTH_4
)
748 host
->cmdat
|= CMD_DAT_CONT_BUS_WIDTH_4
;
750 host
->cmdat
&= ~CMD_DAT_CONT_BUS_WIDTH_4
;
752 if (host
->power_mode
!= ios
->power_mode
) {
753 mxcmci_set_power(host
, ios
->power_mode
, ios
->vdd
);
754 host
->power_mode
= ios
->power_mode
;
756 if (ios
->power_mode
== MMC_POWER_ON
)
757 host
->cmdat
|= CMD_DAT_CONT_INIT
;
761 mxcmci_set_clk_rate(host
, ios
->clock
);
762 writew(STR_STP_CLK_START_CLK
, host
->base
+ MMC_REG_STR_STP_CLK
);
764 writew(STR_STP_CLK_STOP_CLK
, host
->base
+ MMC_REG_STR_STP_CLK
);
767 host
->clock
= ios
->clock
;
770 static irqreturn_t
mxcmci_detect_irq(int irq
, void *data
)
772 struct mmc_host
*mmc
= data
;
774 dev_dbg(mmc_dev(mmc
), "%s\n", __func__
);
776 mmc_detect_change(mmc
, msecs_to_jiffies(250));
780 static int mxcmci_get_ro(struct mmc_host
*mmc
)
782 struct mxcmci_host
*host
= mmc_priv(mmc
);
784 if (host
->pdata
&& host
->pdata
->get_ro
)
785 return !!host
->pdata
->get_ro(mmc_dev(mmc
));
787 * Board doesn't support read only detection; let the mmc core
793 static void mxcmci_enable_sdio_irq(struct mmc_host
*mmc
, int enable
)
795 struct mxcmci_host
*host
= mmc_priv(mmc
);
799 spin_lock_irqsave(&host
->lock
, flags
);
800 host
->use_sdio
= enable
;
801 int_cntr
= readl(host
->base
+ MMC_REG_INT_CNTR
);
804 int_cntr
|= INT_SDIO_IRQ_EN
;
806 int_cntr
&= ~INT_SDIO_IRQ_EN
;
808 writel(int_cntr
, host
->base
+ MMC_REG_INT_CNTR
);
809 spin_unlock_irqrestore(&host
->lock
, flags
);
812 static void mxcmci_init_card(struct mmc_host
*host
, struct mmc_card
*card
)
815 * MX3 SoCs have a silicon bug which corrupts CRC calculation of
816 * multi-block transfers when connected SDIO peripheral doesn't
817 * drive the BUSY line as required by the specs.
818 * One way to prevent this is to only allow 1-bit transfers.
821 if (cpu_is_mx3() && card
->type
== MMC_TYPE_SDIO
)
822 host
->caps
&= ~MMC_CAP_4_BIT_DATA
;
824 host
->caps
|= MMC_CAP_4_BIT_DATA
;
827 static bool filter(struct dma_chan
*chan
, void *param
)
829 struct mxcmci_host
*host
= param
;
831 if (!imx_dma_is_general_purpose(chan
))
834 chan
->private = &host
->dma_data
;
839 static const struct mmc_host_ops mxcmci_ops
= {
840 .request
= mxcmci_request
,
841 .set_ios
= mxcmci_set_ios
,
842 .get_ro
= mxcmci_get_ro
,
843 .enable_sdio_irq
= mxcmci_enable_sdio_irq
,
844 .init_card
= mxcmci_init_card
,
847 static int mxcmci_probe(struct platform_device
*pdev
)
849 struct mmc_host
*mmc
;
850 struct mxcmci_host
*host
= NULL
;
851 struct resource
*iores
, *r
;
855 pr_info("i.MX SDHC driver\n");
857 iores
= platform_get_resource(pdev
, IORESOURCE_MEM
, 0);
858 irq
= platform_get_irq(pdev
, 0);
859 if (!iores
|| irq
< 0)
862 r
= request_mem_region(iores
->start
, resource_size(iores
), pdev
->name
);
866 mmc
= mmc_alloc_host(sizeof(struct mxcmci_host
), &pdev
->dev
);
869 goto out_release_mem
;
872 mmc
->ops
= &mxcmci_ops
;
873 mmc
->caps
= MMC_CAP_4_BIT_DATA
| MMC_CAP_SDIO_IRQ
;
875 /* MMC core transfer sizes tunable parameters */
877 mmc
->max_blk_size
= 2048;
878 mmc
->max_blk_count
= 65535;
879 mmc
->max_req_size
= mmc
->max_blk_size
* mmc
->max_blk_count
;
880 mmc
->max_seg_size
= mmc
->max_req_size
;
882 host
= mmc_priv(mmc
);
883 host
->base
= ioremap(r
->start
, resource_size(r
));
890 host
->pdata
= pdev
->dev
.platform_data
;
891 spin_lock_init(&host
->lock
);
893 mxcmci_init_ocr(host
);
895 if (host
->pdata
&& host
->pdata
->dat3_card_detect
)
896 host
->default_irq_mask
=
897 INT_CARD_INSERTION_EN
| INT_CARD_REMOVAL_EN
;
899 host
->default_irq_mask
= 0;
904 host
->clk_ipg
= devm_clk_get(&pdev
->dev
, "ipg");
905 if (IS_ERR(host
->clk_ipg
)) {
906 ret
= PTR_ERR(host
->clk_ipg
);
910 host
->clk_per
= devm_clk_get(&pdev
->dev
, "per");
911 if (IS_ERR(host
->clk_per
)) {
912 ret
= PTR_ERR(host
->clk_per
);
916 clk_prepare_enable(host
->clk_per
);
917 clk_prepare_enable(host
->clk_ipg
);
919 mxcmci_softreset(host
);
921 host
->rev_no
= readw(host
->base
+ MMC_REG_REV_NO
);
922 if (host
->rev_no
!= 0x400) {
924 dev_err(mmc_dev(host
->mmc
), "wrong rev.no. 0x%08x. aborting.\n",
929 mmc
->f_min
= clk_get_rate(host
->clk_per
) >> 16;
930 mmc
->f_max
= clk_get_rate(host
->clk_per
) >> 1;
932 /* recommended in data sheet */
933 writew(0x2db4, host
->base
+ MMC_REG_READ_TO
);
935 writel(host
->default_irq_mask
, host
->base
+ MMC_REG_INT_CNTR
);
937 r
= platform_get_resource(pdev
, IORESOURCE_DMA
, 0);
939 host
->dmareq
= r
->start
;
940 host
->dma_data
.peripheral_type
= IMX_DMATYPE_SDHC
;
941 host
->dma_data
.priority
= DMA_PRIO_LOW
;
942 host
->dma_data
.dma_request
= host
->dmareq
;
944 dma_cap_set(DMA_SLAVE
, mask
);
945 host
->dma
= dma_request_channel(mask
, filter
, host
);
947 mmc
->max_seg_size
= dma_get_max_seg_size(
948 host
->dma
->device
->dev
);
952 dev_info(mmc_dev(host
->mmc
), "dma not available. Using PIO\n");
954 INIT_WORK(&host
->datawork
, mxcmci_datawork
);
956 ret
= request_irq(host
->irq
, mxcmci_irq
, 0, DRIVER_NAME
, host
);
960 platform_set_drvdata(pdev
, mmc
);
962 if (host
->pdata
&& host
->pdata
->init
) {
963 ret
= host
->pdata
->init(&pdev
->dev
, mxcmci_detect_irq
,
974 free_irq(host
->irq
, host
);
977 dma_release_channel(host
->dma
);
979 clk_disable_unprepare(host
->clk_per
);
980 clk_disable_unprepare(host
->clk_ipg
);
986 release_mem_region(iores
->start
, resource_size(iores
));
990 static int mxcmci_remove(struct platform_device
*pdev
)
992 struct mmc_host
*mmc
= platform_get_drvdata(pdev
);
993 struct mxcmci_host
*host
= mmc_priv(mmc
);
995 platform_set_drvdata(pdev
, NULL
);
997 mmc_remove_host(mmc
);
1000 regulator_put(host
->vcc
);
1002 if (host
->pdata
&& host
->pdata
->exit
)
1003 host
->pdata
->exit(&pdev
->dev
, mmc
);
1005 free_irq(host
->irq
, host
);
1006 iounmap(host
->base
);
1009 dma_release_channel(host
->dma
);
1011 clk_disable_unprepare(host
->clk_per
);
1012 clk_disable_unprepare(host
->clk_ipg
);
1014 release_mem_region(host
->res
->start
, resource_size(host
->res
));
1022 static int mxcmci_suspend(struct device
*dev
)
1024 struct mmc_host
*mmc
= dev_get_drvdata(dev
);
1025 struct mxcmci_host
*host
= mmc_priv(mmc
);
1029 ret
= mmc_suspend_host(mmc
);
1030 clk_disable_unprepare(host
->clk_per
);
1031 clk_disable_unprepare(host
->clk_ipg
);
1036 static int mxcmci_resume(struct device
*dev
)
1038 struct mmc_host
*mmc
= dev_get_drvdata(dev
);
1039 struct mxcmci_host
*host
= mmc_priv(mmc
);
1042 clk_prepare_enable(host
->clk_per
);
1043 clk_prepare_enable(host
->clk_ipg
);
1045 ret
= mmc_resume_host(mmc
);
1050 static const struct dev_pm_ops mxcmci_pm_ops
= {
1051 .suspend
= mxcmci_suspend
,
1052 .resume
= mxcmci_resume
,
1056 static struct platform_driver mxcmci_driver
= {
1057 .probe
= mxcmci_probe
,
1058 .remove
= mxcmci_remove
,
1060 .name
= DRIVER_NAME
,
1061 .owner
= THIS_MODULE
,
1063 .pm
= &mxcmci_pm_ops
,
1068 module_platform_driver(mxcmci_driver
);
1070 MODULE_DESCRIPTION("i.MX Multimedia Card Interface Driver");
1071 MODULE_AUTHOR("Sascha Hauer, Pengutronix");
1072 MODULE_LICENSE("GPL");
1073 MODULE_ALIAS("platform:imx-mmc");