drivers/usb/host/ehci-orion.c

   1 /*
   2  * drivers/usb/host/ehci-orion.c
   3  *
   4  * Tzachi Perelstein <tzachi@marvell.com>
   5  *
   6  * This file is licensed under  the terms of the GNU General Public
   7  * License version 2. This program is licensed "as is" without any
   8  * warranty of any kind, whether express or implied.
   9  */
  10
  11 #include <linux/kernel.h>
  12 #include <linux/module.h>
  13 #include <linux/platform_device.h>
  14 #include <linux/mbus.h>
  15 #include <linux/clk.h>
  16 #include <plat/ehci-orion.h>
  17
  18 #define rdl(off)        __raw_readl(hcd->regs + (off))
  19 #define wrl(off, val)   __raw_writel((val), hcd->regs + (off))
  20
  21 #define USB_CMD                 0x140
  22 #define USB_MODE                0x1a8
  23 #define USB_CAUSE               0x310
  24 #define USB_MASK                0x314
  25 #define USB_WINDOW_CTRL(i)      (0x320 + ((i) << 4))
  26 #define USB_WINDOW_BASE(i)      (0x324 + ((i) << 4))
  27 #define USB_IPG                 0x360
  28 #define USB_PHY_PWR_CTRL        0x400
  29 #define USB_PHY_TX_CTRL         0x420
  30 #define USB_PHY_RX_CTRL         0x430
  31 #define USB_PHY_IVREF_CTRL      0x440
  32 #define USB_PHY_TST_GRP_CTRL    0x450
  33
  34 /*
  35  * Implement Orion USB controller specification guidelines
  36  */
  37 static void orion_usb_phy_v1_setup(struct usb_hcd *hcd)
  38 {
  39         /* The below GLs are according to the Orion Errata document */
  40         /*
  41          * Clear interrupt cause and mask
  42          */
  43         wrl(USB_CAUSE, 0);
  44         wrl(USB_MASK, 0);
  45
  46         /*
  47          * Reset controller
  48          */
  49         wrl(USB_CMD, rdl(USB_CMD) | 0x2);
  50         while (rdl(USB_CMD) & 0x2);
  51
  52         /*
  53          * GL# USB-10: Set IPG for non start of frame packets
  54          * Bits[14:8]=0xc
  55          */
  56         wrl(USB_IPG, (rdl(USB_IPG) & ~0x7f00) | 0xc00);
  57
  58         /*
  59          * GL# USB-9: USB 2.0 Power Control
  60          * BG_VSEL[7:6]=0x1
  61          */
  62         wrl(USB_PHY_PWR_CTRL, (rdl(USB_PHY_PWR_CTRL) & ~0xc0)| 0x40);
  63
  64         /*
  65          * GL# USB-1: USB PHY Tx Control - force calibration to '8'
  66          * TXDATA_BLOCK_EN[21]=0x1, EXT_RCAL_EN[13]=0x1, IMP_CAL[6:3]=0x8
  67          */
  68         wrl(USB_PHY_TX_CTRL, (rdl(USB_PHY_TX_CTRL) & ~0x78) | 0x202040);
  69
  70         /*
  71          * GL# USB-3 GL# USB-9: USB PHY Rx Control
  72          * RXDATA_BLOCK_LENGHT[31:30]=0x3, EDGE_DET_SEL[27:26]=0,
  73          * CDR_FASTLOCK_EN[21]=0, DISCON_THRESHOLD[9:8]=0, SQ_THRESH[7:4]=0x1
  74          */
  75         wrl(USB_PHY_RX_CTRL, (rdl(USB_PHY_RX_CTRL) & ~0xc2003f0) | 0xc0000010);
  76
  77         /*
  78          * GL# USB-3 GL# USB-9: USB PHY IVREF Control
  79          * PLLVDD12[1:0]=0x2, RXVDD[5:4]=0x3, Reserved[19]=0
  80          */
  81         wrl(USB_PHY_IVREF_CTRL, (rdl(USB_PHY_IVREF_CTRL) & ~0x80003 ) | 0x32);
  82
  83         /*
  84          * GL# USB-3 GL# USB-9: USB PHY Test Group Control
  85          * REG_FIFO_SQ_RST[15]=0
  86          */
  87         wrl(USB_PHY_TST_GRP_CTRL, rdl(USB_PHY_TST_GRP_CTRL) & ~0x8000);
  88
  89         /*
  90          * Stop and reset controller
  91          */
  92         wrl(USB_CMD, rdl(USB_CMD) & ~0x1);
  93         wrl(USB_CMD, rdl(USB_CMD) | 0x2);
  94         while (rdl(USB_CMD) & 0x2);
  95
  96         /*
  97          * GL# USB-5 Streaming disable REG_USB_MODE[4]=1
  98          * TBD: This need to be done after each reset!
  99          * GL# USB-4 Setup USB Host mode
 100          */
 101         wrl(USB_MODE, 0x13);
 102 }
 103
 104 static int ehci_orion_setup(struct usb_hcd *hcd)
 105 {
 106         struct ehci_hcd *ehci = hcd_to_ehci(hcd);
 107         int retval;
 108
 109         retval = ehci_setup(hcd);
 110         if (retval)
 111                 return retval;
 112
 113         ehci_port_power(ehci, 0);
 114
 115         return retval;
 116 }
 117
 118 static const struct hc_driver ehci_orion_hc_driver = {
 119         .description = hcd_name,
 120         .product_desc = "Marvell Orion EHCI",
 121         .hcd_priv_size = sizeof(struct ehci_hcd),
 122
 123         /*
 124          * generic hardware linkage
 125          */
 126         .irq = ehci_irq,
 127         .flags = HCD_MEMORY | HCD_USB2,
 128
 129         /*
 130          * basic lifecycle operations
 131          */
 132         .reset = ehci_orion_setup,
 133         .start = ehci_run,
 134         .stop = ehci_stop,
 135         .shutdown = ehci_shutdown,
 136
 137         /*
 138          * managing i/o requests and associated device resources
 139          */
 140         .urb_enqueue = ehci_urb_enqueue,
 141         .urb_dequeue = ehci_urb_dequeue,
 142         .endpoint_disable = ehci_endpoint_disable,
 143         .endpoint_reset = ehci_endpoint_reset,
 144
 145         /*
 146          * scheduling support
 147          */
 148         .get_frame_number = ehci_get_frame,
 149
 150         /*
 151          * root hub support
 152          */
 153         .hub_status_data = ehci_hub_status_data,
 154         .hub_control = ehci_hub_control,
 155         .bus_suspend = ehci_bus_suspend,
 156         .bus_resume = ehci_bus_resume,
 157         .relinquish_port = ehci_relinquish_port,
 158         .port_handed_over = ehci_port_handed_over,
 159
 160         .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
 161 };
 162
 163 static void __init
 164 ehci_orion_conf_mbus_windows(struct usb_hcd *hcd,
 165                              const struct mbus_dram_target_info *dram)
 166 {
 167         int i;
 168
 169         for (i = 0; i < 4; i++) {
 170                 wrl(USB_WINDOW_CTRL(i), 0);
 171                 wrl(USB_WINDOW_BASE(i), 0);
 172         }
 173
 174         for (i = 0; i < dram->num_cs; i++) {
 175                 const struct mbus_dram_window *cs = dram->cs + i;
 176
 177                 wrl(USB_WINDOW_CTRL(i), ((cs->size - 1) & 0xffff0000) |
 178                                         (cs->mbus_attr << 8) |
 179                                         (dram->mbus_dram_target_id << 4) | 1);
 180                 wrl(USB_WINDOW_BASE(i), cs->base);
 181         }
 182 }
 183
 184 static int __devinit ehci_orion_drv_probe(struct platform_device *pdev)
 185 {
 186         struct orion_ehci_data *pd = pdev->dev.platform_data;
 187         const struct mbus_dram_target_info *dram;
 188         struct resource *res;
 189         struct usb_hcd *hcd;
 190         struct ehci_hcd *ehci;
 191         struct clk *clk;
 192         void __iomem *regs;
 193         int irq, err;
 194
 195         if (usb_disabled())
 196                 return -ENODEV;
 197
 198         pr_debug("Initializing Orion-SoC USB Host Controller\n");
 199
 200         irq = platform_get_irq(pdev, 0);
 201         if (irq <= 0) {
 202                 dev_err(&pdev->dev,
 203                         "Found HC with no IRQ. Check %s setup!\n",
 204                         dev_name(&pdev->dev));
 205                 err = -ENODEV;
 206                 goto err1;
 207         }
 208
 209         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 210         if (!res) {
 211                 dev_err(&pdev->dev,
 212                         "Found HC with no register addr. Check %s setup!\n",
 213                         dev_name(&pdev->dev));
 214                 err = -ENODEV;
 215                 goto err1;
 216         }
 217
 218         if (!request_mem_region(res->start, resource_size(res),
 219                                 ehci_orion_hc_driver.description)) {
 220                 dev_dbg(&pdev->dev, "controller already in use\n");
 221                 err = -EBUSY;
 222                 goto err1;
 223         }
 224
 225         regs = ioremap(res->start, resource_size(res));
 226         if (regs == NULL) {
 227                 dev_dbg(&pdev->dev, "error mapping memory\n");
 228                 err = -EFAULT;
 229                 goto err2;
 230         }
 231
 232         /* Not all platforms can gate the clock, so it is not
 233            an error if the clock does not exists. */
 234         clk = clk_get(&pdev->dev, NULL);
 235         if (!IS_ERR(clk)) {
 236                 clk_prepare_enable(clk);
 237                 clk_put(clk);
 238         }
 239
 240         hcd = usb_create_hcd(&ehci_orion_hc_driver,
 241                         &pdev->dev, dev_name(&pdev->dev));
 242         if (!hcd) {
 243                 err = -ENOMEM;
 244                 goto err3;
 245         }
 246
 247         hcd->rsrc_start = res->start;
 248         hcd->rsrc_len = resource_size(res);
 249         hcd->regs = regs;
 250
 251         ehci = hcd_to_ehci(hcd);
 252         ehci->caps = hcd->regs + 0x100;
 253         hcd->has_tt = 1;
 254
 255         /*
 256          * (Re-)program MBUS remapping windows if we are asked to.
 257          */
 258         dram = mv_mbus_dram_info();
 259         if (dram)
 260                 ehci_orion_conf_mbus_windows(hcd, dram);
 261
 262         /*
 263          * setup Orion USB controller.
 264          */
 265         switch (pd->phy_version) {
 266         case EHCI_PHY_NA:       /* dont change USB phy settings */
 267                 break;
 268         case EHCI_PHY_ORION:
 269                 orion_usb_phy_v1_setup(hcd);
 270                 break;
 271         case EHCI_PHY_DD:
 272         case EHCI_PHY_KW:
 273         default:
 274                 printk(KERN_WARNING "Orion ehci -USB phy version isn't supported.\n");
 275         }
 276
 277         err = usb_add_hcd(hcd, irq, IRQF_SHARED);
 278         if (err)
 279                 goto err4;
 280
 281         return 0;
 282
 283 err4:
 284         usb_put_hcd(hcd);
 285 err3:
 286         if (!IS_ERR(clk)) {
 287                 clk_disable_unprepare(clk);
 288                 clk_put(clk);
 289         }
 290         iounmap(regs);
 291 err2:
 292         release_mem_region(res->start, resource_size(res));
 293 err1:
 294         dev_err(&pdev->dev, "init %s fail, %d\n",
 295                 dev_name(&pdev->dev), err);
 296
 297         return err;
 298 }
 299
 300 static int __exit ehci_orion_drv_remove(struct platform_device *pdev)
 301 {
 302         struct usb_hcd *hcd = platform_get_drvdata(pdev);
 303         struct clk *clk;
 304
 305         usb_remove_hcd(hcd);
 306         iounmap(hcd->regs);
 307         release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 308         usb_put_hcd(hcd);
 309
 310         clk = clk_get(&pdev->dev, NULL);
 311         if (!IS_ERR(clk)) {
 312                 clk_disable_unprepare(clk);
 313                 clk_put(clk);
 314         }
 315         return 0;
 316 }
 317
 318 MODULE_ALIAS("platform:orion-ehci");
 319
 320 static struct platform_driver ehci_orion_driver = {
 321         .probe          = ehci_orion_drv_probe,
 322         .remove         = __exit_p(ehci_orion_drv_remove),
 323         .shutdown       = usb_hcd_platform_shutdown,
 324         .driver.name    = "orion-ehci",
 325 };