?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
x86, mrst: use a temporary variable for SFI irq
[linux-btrfs-devel.git] / drivers / ata / ata_piix.c
blob43107e9415da7efd1405195cb5ca6dc3d1168d25
1 /*
2 * ata_piix.c - Intel PATA/SATA controllers
3 *
4 * Maintained by: Jeff Garzik <jgarzik@pobox.com>
5 * Please ALWAYS copy linux-ide@vger.kernel.org
6 * on emails.
7 *
8 *
9 * Copyright 2003-2005 Red Hat Inc
10 * Copyright 2003-2005 Jeff Garzik
11 *
12 *
13 * Copyright header from piix.c:
14 *
15 * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
16 * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
17 * Copyright (C) 2003 Red Hat Inc
18 *
19 *
20 * This program is free software; you can redistribute it and/or modify
21 * it under the terms of the GNU General Public License as published by
22 * the Free Software Foundation; either version 2, or (at your option)
23 * any later version.
24 *
25 * This program is distributed in the hope that it will be useful,
26 * but WITHOUT ANY WARRANTY; without even the implied warranty of
27 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
28 * GNU General Public License for more details.
29 *
30 * You should have received a copy of the GNU General Public License
31 * along with this program; see the file COPYING. If not, write to
32 * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
33 *
34 *
35 * libata documentation is available via 'make {ps|pdf}docs',
36 * as Documentation/DocBook/libata.*
37 *
38 * Hardware documentation available at http://developer.intel.com/
39 *
40 * Documentation
41 * Publicly available from Intel web site. Errata documentation
42 * is also publicly available. As an aide to anyone hacking on this
43 * driver the list of errata that are relevant is below, going back to
44 * PIIX4. Older device documentation is now a bit tricky to find.
45 *
46 * The chipsets all follow very much the same design. The original Triton
47 * series chipsets do _not_ support independent device timings, but this
48 * is fixed in Triton II. With the odd mobile exception the chips then
49 * change little except in gaining more modes until SATA arrives. This
50 * driver supports only the chips with independent timing (that is those
51 * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix
52 * for the early chip drivers.
53 *
54 * Errata of note:
55 *
56 * Unfixable
57 * PIIX4 errata #9 - Only on ultra obscure hw
58 * ICH3 errata #13 - Not observed to affect real hw
59 * by Intel
60 *
61 * Things we must deal with
62 * PIIX4 errata #10 - BM IDE hang with non UDMA
63 * (must stop/start dma to recover)
64 * 440MX errata #15 - As PIIX4 errata #10
65 * PIIX4 errata #15 - Must not read control registers
66 * during a PIO transfer
67 * 440MX errata #13 - As PIIX4 errata #15
68 * ICH2 errata #21 - DMA mode 0 doesn't work right
69 * ICH0/1 errata #55 - As ICH2 errata #21
70 * ICH2 spec c #9 - Extra operations needed to handle
71 * drive hotswap [NOT YET SUPPORTED]
72 * ICH2 spec c #20 - IDE PRD must not cross a 64K boundary
73 * and must be dword aligned
74 * ICH2 spec c #24 - UDMA mode 4,5 t85/86 should be 6ns not 3.3
75 * ICH7 errata #16 - MWDMA1 timings are incorrect
76 *
77 * Should have been BIOS fixed:
78 * 450NX: errata #19 - DMA hangs on old 450NX
79 * 450NX: errata #20 - DMA hangs on old 450NX
80 * 450NX: errata #25 - Corruption with DMA on old 450NX
81 * ICH3 errata #15 - IDE deadlock under high load
82 * (BIOS must set dev 31 fn 0 bit 23)
83 * ICH3 errata #18 - Don't use native mode
84 */
85
86 #include <linux/kernel.h>
87 #include <linux/module.h>
88 #include <linux/pci.h>
89 #include <linux/init.h>
90 #include <linux/blkdev.h>
91 #include <linux/delay.h>
92 #include <linux/device.h>
93 #include <linux/gfp.h>
94 #include <scsi/scsi_host.h>
95 #include <linux/libata.h>
96 #include <linux/dmi.h>
97
98 #define DRV_NAME "ata_piix"
99 #define DRV_VERSION "2.13"
100
101 enum {
102 PIIX_IOCFG = 0x54, /* IDE I/O configuration register */
103 ICH5_PMR = 0x90, /* port mapping register */
104 ICH5_PCS = 0x92, /* port control and status */
105 PIIX_SIDPR_BAR = 5,
106 PIIX_SIDPR_LEN = 16,
107 PIIX_SIDPR_IDX = 0,
108 PIIX_SIDPR_DATA = 4,
109
110 PIIX_FLAG_CHECKINTR = (1 << 28), /* make sure PCI INTx enabled */
111 PIIX_FLAG_SIDPR = (1 << 29), /* SATA idx/data pair regs */
112
113 PIIX_PATA_FLAGS = ATA_FLAG_SLAVE_POSS,
114 PIIX_SATA_FLAGS = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR,
115
116 PIIX_80C_PRI = (1 << 5) | (1 << 4),
117 PIIX_80C_SEC = (1 << 7) | (1 << 6),
118
119 /* constants for mapping table */
120 P0 = 0, /* port 0 */
121 P1 = 1, /* port 1 */
122 P2 = 2, /* port 2 */
123 P3 = 3, /* port 3 */
124 IDE = -1, /* IDE */
125 NA = -2, /* not available */
126 RV = -3, /* reserved */
127
128 PIIX_AHCI_DEVICE = 6,
129
130 /* host->flags bits */
131 PIIX_HOST_BROKEN_SUSPEND = (1 << 24),
132 };
133
134 enum piix_controller_ids {
135 /* controller IDs */
136 piix_pata_mwdma, /* PIIX3 MWDMA only */
137 piix_pata_33, /* PIIX4 at 33Mhz */
138 ich_pata_33, /* ICH up to UDMA 33 only */
139 ich_pata_66, /* ICH up to 66 Mhz */
140 ich_pata_100, /* ICH up to UDMA 100 */
141 ich_pata_100_nomwdma1, /* ICH up to UDMA 100 but with no MWDMA1*/
142 ich5_sata,
143 ich6_sata,
144 ich6m_sata,
145 ich8_sata,
146 ich8_2port_sata,
147 ich8m_apple_sata, /* locks up on second port enable */
148 tolapai_sata,
149 piix_pata_vmw, /* PIIX4 for VMware, spurious DMA_ERR */
150 };
151
152 struct piix_map_db {
153 const u32 mask;
154 const u16 port_enable;
155 const int map[][4];
156 };
157
158 struct piix_host_priv {
159 const int *map;
160 u32 saved_iocfg;
161 void __iomem *sidpr;
162 };
163
164 static int piix_init_one(struct pci_dev *pdev,
165 const struct pci_device_id *ent);
166 static void piix_remove_one(struct pci_dev *pdev);
167 static int piix_pata_prereset(struct ata_link *link, unsigned long deadline);
168 static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev);
169 static void piix_set_dmamode(struct ata_port *ap, struct ata_device *adev);
170 static void ich_set_dmamode(struct ata_port *ap, struct ata_device *adev);
171 static int ich_pata_cable_detect(struct ata_port *ap);
172 static u8 piix_vmw_bmdma_status(struct ata_port *ap);
173 static int piix_sidpr_scr_read(struct ata_link *link,
174 unsigned int reg, u32 *val);
175 static int piix_sidpr_scr_write(struct ata_link *link,
176 unsigned int reg, u32 val);
177 static int piix_sidpr_set_lpm(struct ata_link *link, enum ata_lpm_policy policy,
178 unsigned hints);
179 static bool piix_irq_check(struct ata_port *ap);
180 #ifdef CONFIG_PM
181 static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
182 static int piix_pci_device_resume(struct pci_dev *pdev);
183 #endif
184
185 static unsigned int in_module_init = 1;
186
187 static const struct pci_device_id piix_pci_tbl[] = {
188 /* Intel PIIX3 for the 430HX etc */
189 { 0x8086, 0x7010, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_mwdma },
190 /* VMware ICH4 */
191 { 0x8086, 0x7111, 0x15ad, 0x1976, 0, 0, piix_pata_vmw },
192 /* Intel PIIX4 for the 430TX/440BX/MX chipset: UDMA 33 */
193 /* Also PIIX4E (fn3 rev 2) and PIIX4M (fn3 rev 3) */
194 { 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
195 /* Intel PIIX4 */
196 { 0x8086, 0x7199, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
197 /* Intel PIIX4 */
198 { 0x8086, 0x7601, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
199 /* Intel PIIX */
200 { 0x8086, 0x84CA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
201 /* Intel ICH (i810, i815, i840) UDMA 66*/
202 { 0x8086, 0x2411, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_66 },
203 /* Intel ICH0 : UDMA 33*/
204 { 0x8086, 0x2421, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_33 },
205 /* Intel ICH2M */
206 { 0x8086, 0x244A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
207 /* Intel ICH2 (i810E2, i845, 850, 860) UDMA 100 */
208 { 0x8086, 0x244B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
209 /* Intel ICH3M */
210 { 0x8086, 0x248A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
211 /* Intel ICH3 (E7500/1) UDMA 100 */
212 { 0x8086, 0x248B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
213 /* Intel ICH4-L */
214 { 0x8086, 0x24C1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
215 /* Intel ICH4 (i845GV, i845E, i852, i855) UDMA 100 */
216 { 0x8086, 0x24CA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
217 { 0x8086, 0x24CB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
218 /* Intel ICH5 */
219 { 0x8086, 0x24DB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
220 /* C-ICH (i810E2) */
221 { 0x8086, 0x245B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
222 /* ESB (855GME/875P + 6300ESB) UDMA 100 */
223 { 0x8086, 0x25A2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
224 /* ICH6 (and 6) (i915) UDMA 100 */
225 { 0x8086, 0x266F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
226 /* ICH7/7-R (i945, i975) UDMA 100*/
227 { 0x8086, 0x27DF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100_nomwdma1 },
228 { 0x8086, 0x269E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100_nomwdma1 },
229 /* ICH8 Mobile PATA Controller */
230 { 0x8086, 0x2850, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
231
232 /* SATA ports */
233
234 /* 82801EB (ICH5) */
235 { 0x8086, 0x24d1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
236 /* 82801EB (ICH5) */
237 { 0x8086, 0x24df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
238 /* 6300ESB (ICH5 variant with broken PCS present bits) */
239 { 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
240 /* 6300ESB pretending RAID */
241 { 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
242 /* 82801FB/FW (ICH6/ICH6W) */
243 { 0x8086, 0x2651, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
244 /* 82801FR/FRW (ICH6R/ICH6RW) */
245 { 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
246 /* 82801FBM ICH6M (ICH6R with only port 0 and 2 implemented).
247 * Attach iff the controller is in IDE mode. */
248 { 0x8086, 0x2653, PCI_ANY_ID, PCI_ANY_ID,
249 PCI_CLASS_STORAGE_IDE << 8, 0xffff00, ich6m_sata },
250 /* 82801GB/GR/GH (ICH7, identical to ICH6) */
251 { 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
252 /* 2801GBM/GHM (ICH7M, identical to ICH6M) */
253 { 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata },
254 /* Enterprise Southbridge 2 (631xESB/632xESB) */
255 { 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
256 /* SATA Controller 1 IDE (ICH8) */
257 { 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
258 /* SATA Controller 2 IDE (ICH8) */
259 { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
260 /* Mobile SATA Controller IDE (ICH8M), Apple */
261 { 0x8086, 0x2828, 0x106b, 0x00a0, 0, 0, ich8m_apple_sata },
262 { 0x8086, 0x2828, 0x106b, 0x00a1, 0, 0, ich8m_apple_sata },
263 { 0x8086, 0x2828, 0x106b, 0x00a3, 0, 0, ich8m_apple_sata },
264 /* Mobile SATA Controller IDE (ICH8M) */
265 { 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
266 /* SATA Controller IDE (ICH9) */
267 { 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
268 /* SATA Controller IDE (ICH9) */
269 { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
270 /* SATA Controller IDE (ICH9) */
271 { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
272 /* SATA Controller IDE (ICH9M) */
273 { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
274 /* SATA Controller IDE (ICH9M) */
275 { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
276 /* SATA Controller IDE (ICH9M) */
277 { 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
278 /* SATA Controller IDE (Tolapai) */
279 { 0x8086, 0x5028, PCI_ANY_ID, PCI_ANY_ID, 0, 0, tolapai_sata },
280 /* SATA Controller IDE (ICH10) */
281 { 0x8086, 0x3a00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
282 /* SATA Controller IDE (ICH10) */
283 { 0x8086, 0x3a06, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
284 /* SATA Controller IDE (ICH10) */
285 { 0x8086, 0x3a20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
286 /* SATA Controller IDE (ICH10) */
287 { 0x8086, 0x3a26, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
288 /* SATA Controller IDE (PCH) */
289 { 0x8086, 0x3b20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
290 /* SATA Controller IDE (PCH) */
291 { 0x8086, 0x3b21, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
292 /* SATA Controller IDE (PCH) */
293 { 0x8086, 0x3b26, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
294 /* SATA Controller IDE (PCH) */
295 { 0x8086, 0x3b28, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
296 /* SATA Controller IDE (PCH) */
297 { 0x8086, 0x3b2d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
298 /* SATA Controller IDE (PCH) */
299 { 0x8086, 0x3b2e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
300 /* SATA Controller IDE (CPT) */
301 { 0x8086, 0x1c00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
302 /* SATA Controller IDE (CPT) */
303 { 0x8086, 0x1c01, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
304 /* SATA Controller IDE (CPT) */
305 { 0x8086, 0x1c08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
306 /* SATA Controller IDE (CPT) */
307 { 0x8086, 0x1c09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
308 /* SATA Controller IDE (PBG) */
309 { 0x8086, 0x1d00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
310 /* SATA Controller IDE (PBG) */
311 { 0x8086, 0x1d08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
312 /* SATA Controller IDE (Panther Point) */
313 { 0x8086, 0x1e00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
314 /* SATA Controller IDE (Panther Point) */
315 { 0x8086, 0x1e01, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
316 /* SATA Controller IDE (Panther Point) */
317 { 0x8086, 0x1e08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
318 /* SATA Controller IDE (Panther Point) */
319 { 0x8086, 0x1e09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
320 { } /* terminate list */
321 };
322
323 static struct pci_driver piix_pci_driver = {
324 .name = DRV_NAME,
325 .id_table = piix_pci_tbl,
326 .probe = piix_init_one,
327 .remove = piix_remove_one,
328 #ifdef CONFIG_PM
329 .suspend = piix_pci_device_suspend,
330 .resume = piix_pci_device_resume,
331 #endif
332 };
333
334 static struct scsi_host_template piix_sht = {
335 ATA_BMDMA_SHT(DRV_NAME),
336 };
337
338 static struct ata_port_operations piix_sata_ops = {
339 .inherits = &ata_bmdma32_port_ops,
340 .sff_irq_check = piix_irq_check,
341 };
342
343 static struct ata_port_operations piix_pata_ops = {
344 .inherits = &piix_sata_ops,
345 .cable_detect = ata_cable_40wire,
346 .set_piomode = piix_set_piomode,
347 .set_dmamode = piix_set_dmamode,
348 .prereset = piix_pata_prereset,
349 };
350
351 static struct ata_port_operations piix_vmw_ops = {
352 .inherits = &piix_pata_ops,
353 .bmdma_status = piix_vmw_bmdma_status,
354 };
355
356 static struct ata_port_operations ich_pata_ops = {
357 .inherits = &piix_pata_ops,
358 .cable_detect = ich_pata_cable_detect,
359 .set_dmamode = ich_set_dmamode,
360 };
361
362 static struct device_attribute *piix_sidpr_shost_attrs[] = {
363 &dev_attr_link_power_management_policy,
364 NULL
365 };
366
367 static struct scsi_host_template piix_sidpr_sht = {
368 ATA_BMDMA_SHT(DRV_NAME),
369 .shost_attrs = piix_sidpr_shost_attrs,
370 };
371
372 static struct ata_port_operations piix_sidpr_sata_ops = {
373 .inherits = &piix_sata_ops,
374 .hardreset = sata_std_hardreset,
375 .scr_read = piix_sidpr_scr_read,
376 .scr_write = piix_sidpr_scr_write,
377 .set_lpm = piix_sidpr_set_lpm,
378 };
379
380 static const struct piix_map_db ich5_map_db = {
381 .mask = 0x7,
382 .port_enable = 0x3,
383 .map = {
384 /* PM PS SM SS MAP */
385 { P0, NA, P1, NA }, /* 000b */
386 { P1, NA, P0, NA }, /* 001b */
387 { RV, RV, RV, RV },
388 { RV, RV, RV, RV },
389 { P0, P1, IDE, IDE }, /* 100b */
390 { P1, P0, IDE, IDE }, /* 101b */
391 { IDE, IDE, P0, P1 }, /* 110b */
392 { IDE, IDE, P1, P0 }, /* 111b */
393 },
394 };
395
396 static const struct piix_map_db ich6_map_db = {
397 .mask = 0x3,
398 .port_enable = 0xf,
399 .map = {
400 /* PM PS SM SS MAP */
401 { P0, P2, P1, P3 }, /* 00b */
402 { IDE, IDE, P1, P3 }, /* 01b */
403 { P0, P2, IDE, IDE }, /* 10b */
404 { RV, RV, RV, RV },
405 },
406 };
407
408 static const struct piix_map_db ich6m_map_db = {
409 .mask = 0x3,
410 .port_enable = 0x5,
411
412 /* Map 01b isn't specified in the doc but some notebooks use
413 * it anyway. MAP 01b have been spotted on both ICH6M and
414 * ICH7M.
415 */
416 .map = {
417 /* PM PS SM SS MAP */
418 { P0, P2, NA, NA }, /* 00b */
419 { IDE, IDE, P1, P3 }, /* 01b */
420 { P0, P2, IDE, IDE }, /* 10b */
421 { RV, RV, RV, RV },
422 },
423 };
424
425 static const struct piix_map_db ich8_map_db = {
426 .mask = 0x3,
427 .port_enable = 0xf,
428 .map = {
429 /* PM PS SM SS MAP */
430 { P0, P2, P1, P3 }, /* 00b (hardwired when in AHCI) */
431 { RV, RV, RV, RV },
432 { P0, P2, IDE, IDE }, /* 10b (IDE mode) */
433 { RV, RV, RV, RV },
434 },
435 };
436
437 static const struct piix_map_db ich8_2port_map_db = {
438 .mask = 0x3,
439 .port_enable = 0x3,
440 .map = {
441 /* PM PS SM SS MAP */
442 { P0, NA, P1, NA }, /* 00b */
443 { RV, RV, RV, RV }, /* 01b */
444 { RV, RV, RV, RV }, /* 10b */
445 { RV, RV, RV, RV },
446 },
447 };
448
449 static const struct piix_map_db ich8m_apple_map_db = {
450 .mask = 0x3,
451 .port_enable = 0x1,
452 .map = {
453 /* PM PS SM SS MAP */
454 { P0, NA, NA, NA }, /* 00b */
455 { RV, RV, RV, RV },
456 { P0, P2, IDE, IDE }, /* 10b */
457 { RV, RV, RV, RV },
458 },
459 };
460
461 static const struct piix_map_db tolapai_map_db = {
462 .mask = 0x3,
463 .port_enable = 0x3,
464 .map = {
465 /* PM PS SM SS MAP */
466 { P0, NA, P1, NA }, /* 00b */
467 { RV, RV, RV, RV }, /* 01b */
468 { RV, RV, RV, RV }, /* 10b */
469 { RV, RV, RV, RV },
470 },
471 };
472
473 static const struct piix_map_db *piix_map_db_table[] = {
474 [ich5_sata] = &ich5_map_db,
475 [ich6_sata] = &ich6_map_db,
476 [ich6m_sata] = &ich6m_map_db,
477 [ich8_sata] = &ich8_map_db,
478 [ich8_2port_sata] = &ich8_2port_map_db,
479 [ich8m_apple_sata] = &ich8m_apple_map_db,
480 [tolapai_sata] = &tolapai_map_db,
481 };
482
483 static struct ata_port_info piix_port_info[] = {
484 [piix_pata_mwdma] = /* PIIX3 MWDMA only */
485 {
486 .flags = PIIX_PATA_FLAGS,
487 .pio_mask = ATA_PIO4,
488 .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
489 .port_ops = &piix_pata_ops,
490 },
491
492 [piix_pata_33] = /* PIIX4 at 33MHz */
493 {
494 .flags = PIIX_PATA_FLAGS,
495 .pio_mask = ATA_PIO4,
496 .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
497 .udma_mask = ATA_UDMA2,
498 .port_ops = &piix_pata_ops,
499 },
500
501 [ich_pata_33] = /* ICH0 - ICH at 33Mhz*/
502 {
503 .flags = PIIX_PATA_FLAGS,
504 .pio_mask = ATA_PIO4,
505 .mwdma_mask = ATA_MWDMA12_ONLY, /* Check: maybe MWDMA0 is ok */
506 .udma_mask = ATA_UDMA2,
507 .port_ops = &ich_pata_ops,
508 },
509
510 [ich_pata_66] = /* ICH controllers up to 66MHz */
511 {
512 .flags = PIIX_PATA_FLAGS,
513 .pio_mask = ATA_PIO4,
514 .mwdma_mask = ATA_MWDMA12_ONLY, /* MWDMA0 is broken on chip */
515 .udma_mask = ATA_UDMA4,
516 .port_ops = &ich_pata_ops,
517 },
518
519 [ich_pata_100] =
520 {
521 .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR,
522 .pio_mask = ATA_PIO4,
523 .mwdma_mask = ATA_MWDMA12_ONLY,
524 .udma_mask = ATA_UDMA5,
525 .port_ops = &ich_pata_ops,
526 },
527
528 [ich_pata_100_nomwdma1] =
529 {
530 .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR,
531 .pio_mask = ATA_PIO4,
532 .mwdma_mask = ATA_MWDMA2_ONLY,
533 .udma_mask = ATA_UDMA5,
534 .port_ops = &ich_pata_ops,
535 },
536
537 [ich5_sata] =
538 {
539 .flags = PIIX_SATA_FLAGS,
540 .pio_mask = ATA_PIO4,
541 .mwdma_mask = ATA_MWDMA2,
542 .udma_mask = ATA_UDMA6,
543 .port_ops = &piix_sata_ops,
544 },
545
546 [ich6_sata] =
547 {
548 .flags = PIIX_SATA_FLAGS,
549 .pio_mask = ATA_PIO4,
550 .mwdma_mask = ATA_MWDMA2,
551 .udma_mask = ATA_UDMA6,
552 .port_ops = &piix_sata_ops,
553 },
554
555 [ich6m_sata] =
556 {
557 .flags = PIIX_SATA_FLAGS,
558 .pio_mask = ATA_PIO4,
559 .mwdma_mask = ATA_MWDMA2,
560 .udma_mask = ATA_UDMA6,
561 .port_ops = &piix_sata_ops,
562 },
563
564 [ich8_sata] =
565 {
566 .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR,
567 .pio_mask = ATA_PIO4,
568 .mwdma_mask = ATA_MWDMA2,
569 .udma_mask = ATA_UDMA6,
570 .port_ops = &piix_sata_ops,
571 },
572
573 [ich8_2port_sata] =
574 {
575 .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR,
576 .pio_mask = ATA_PIO4,
577 .mwdma_mask = ATA_MWDMA2,
578 .udma_mask = ATA_UDMA6,
579 .port_ops = &piix_sata_ops,
580 },
581
582 [tolapai_sata] =
583 {
584 .flags = PIIX_SATA_FLAGS,
585 .pio_mask = ATA_PIO4,
586 .mwdma_mask = ATA_MWDMA2,
587 .udma_mask = ATA_UDMA6,
588 .port_ops = &piix_sata_ops,
589 },
590
591 [ich8m_apple_sata] =
592 {
593 .flags = PIIX_SATA_FLAGS,
594 .pio_mask = ATA_PIO4,
595 .mwdma_mask = ATA_MWDMA2,
596 .udma_mask = ATA_UDMA6,
597 .port_ops = &piix_sata_ops,
598 },
599
600 [piix_pata_vmw] =
601 {
602 .flags = PIIX_PATA_FLAGS,
603 .pio_mask = ATA_PIO4,
604 .mwdma_mask = ATA_MWDMA12_ONLY, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
605 .udma_mask = ATA_UDMA2,
606 .port_ops = &piix_vmw_ops,
607 },
608
609 };
610
611 static struct pci_bits piix_enable_bits[] = {
612 { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
613 { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */
614 };
615
616 MODULE_AUTHOR("Andre Hedrick, Alan Cox, Andrzej Krzysztofowicz, Jeff Garzik");
617 MODULE_DESCRIPTION("SCSI low-level driver for Intel PIIX/ICH ATA controllers");
618 MODULE_LICENSE("GPL");
619 MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
620 MODULE_VERSION(DRV_VERSION);
621
622 struct ich_laptop {
623 u16 device;
624 u16 subvendor;
625 u16 subdevice;
626 };
627
628 /*
629 * List of laptops that use short cables rather than 80 wire
630 */
631
632 static const struct ich_laptop ich_laptop[] = {
633 /* devid, subvendor, subdev */
634 { 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
635 { 0x27DF, 0x1025, 0x0102 }, /* ICH7 on Acer 5602aWLMi */
636 { 0x27DF, 0x1025, 0x0110 }, /* ICH7 on Acer 3682WLMi */
637 { 0x27DF, 0x1028, 0x02b0 }, /* ICH7 on unknown Dell */
638 { 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */
639 { 0x27DF, 0x103C, 0x30A1 }, /* ICH7 on HP Compaq nc2400 */
640 { 0x27DF, 0x103C, 0x361a }, /* ICH7 on unknown HP */
641 { 0x27DF, 0x1071, 0xD221 }, /* ICH7 on Hercules EC-900 */
642 { 0x27DF, 0x152D, 0x0778 }, /* ICH7 on unknown Intel */
643 { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on ACER Aspire 2023WLMi */
644 { 0x24CA, 0x1025, 0x003d }, /* ICH4 on ACER TM290 */
645 { 0x266F, 0x1025, 0x0066 }, /* ICH6 on ACER Aspire 1694WLMi */
646 { 0x2653, 0x1043, 0x82D8 }, /* ICH6M on Asus Eee 701 */
647 { 0x27df, 0x104d, 0x900e }, /* ICH7 on Sony TZ-90 */
648 /* end marker */
649 { 0, }
650 };
651
652 /**
653 * ich_pata_cable_detect - Probe host controller cable detect info
654 * @ap: Port for which cable detect info is desired
655 *
656 * Read 80c cable indicator from ATA PCI device's PCI config
657 * register. This register is normally set by firmware (BIOS).
658 *
659 * LOCKING:
660 * None (inherited from caller).
661 */
662
663 static int ich_pata_cable_detect(struct ata_port *ap)
664 {
665 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
666 struct piix_host_priv *hpriv = ap->host->private_data;
667 const struct ich_laptop *lap = &ich_laptop[0];
668 u8 mask;
669
670 /* Check for specials - Acer Aspire 5602WLMi */
671 while (lap->device) {
672 if (lap->device == pdev->device &&
673 lap->subvendor == pdev->subsystem_vendor &&
674 lap->subdevice == pdev->subsystem_device)
675 return ATA_CBL_PATA40_SHORT;
676
677 lap++;
678 }
679
680 /* check BIOS cable detect results */
681 mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
682 if ((hpriv->saved_iocfg & mask) == 0)
683 return ATA_CBL_PATA40;
684 return ATA_CBL_PATA80;
685 }
686
687 /**
688 * piix_pata_prereset - prereset for PATA host controller
689 * @link: Target link
690 * @deadline: deadline jiffies for the operation
691 *
692 * LOCKING:
693 * None (inherited from caller).
694 */
695 static int piix_pata_prereset(struct ata_link *link, unsigned long deadline)
696 {
697 struct ata_port *ap = link->ap;
698 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
699
700 if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no]))
701 return -ENOENT;
702 return ata_sff_prereset(link, deadline);
703 }
704
705 static DEFINE_SPINLOCK(piix_lock);
706
707 /**
708 * piix_set_piomode - Initialize host controller PATA PIO timings
709 * @ap: Port whose timings we are configuring
710 * @adev: um
711 *
712 * Set PIO mode for device, in host controller PCI config space.
713 *
714 * LOCKING:
715 * None (inherited from caller).
716 */
717
718 static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev)
719 {
720 struct pci_dev *dev = to_pci_dev(ap->host->dev);
721 unsigned long flags;
722 unsigned int pio = adev->pio_mode - XFER_PIO_0;
723 unsigned int is_slave = (adev->devno != 0);
724 unsigned int master_port= ap->port_no ? 0x42 : 0x40;
725 unsigned int slave_port = 0x44;
726 u16 master_data;
727 u8 slave_data;
728 u8 udma_enable;
729 int control = 0;
730
731 /*
732 * See Intel Document 298600-004 for the timing programing rules
733 * for ICH controllers.
734 */
735
736 static const /* ISP RTC */
737 u8 timings[][2] = { { 0, 0 },
738 { 0, 0 },
739 { 1, 0 },
740 { 2, 1 },
741 { 2, 3 }, };
742
743 if (pio >= 2)
744 control |= 1; /* TIME1 enable */
745 if (ata_pio_need_iordy(adev))
746 control |= 2; /* IE enable */
747
748 /* Intel specifies that the PPE functionality is for disk only */
749 if (adev->class == ATA_DEV_ATA)
750 control |= 4; /* PPE enable */
751
752 spin_lock_irqsave(&piix_lock, flags);
753
754 /* PIO configuration clears DTE unconditionally. It will be
755 * programmed in set_dmamode which is guaranteed to be called
756 * after set_piomode if any DMA mode is available.
757 */
758 pci_read_config_word(dev, master_port, &master_data);
759 if (is_slave) {
760 /* clear TIME1|IE1|PPE1|DTE1 */
761 master_data &= 0xff0f;
762 /* Enable SITRE (separate slave timing register) */
763 master_data |= 0x4000;
764 /* enable PPE1, IE1 and TIME1 as needed */
765 master_data |= (control << 4);
766 pci_read_config_byte(dev, slave_port, &slave_data);
767 slave_data &= (ap->port_no ? 0x0f : 0xf0);
768 /* Load the timing nibble for this slave */
769 slave_data |= ((timings[pio][0] << 2) | timings[pio][1])
770 << (ap->port_no ? 4 : 0);
771 } else {
772 /* clear ISP|RCT|TIME0|IE0|PPE0|DTE0 */
773 master_data &= 0xccf0;
774 /* Enable PPE, IE and TIME as appropriate */
775 master_data |= control;
776 /* load ISP and RCT */
777 master_data |=
778 (timings[pio][0] << 12) |
779 (timings[pio][1] << 8);
780 }
781 pci_write_config_word(dev, master_port, master_data);
782 if (is_slave)
783 pci_write_config_byte(dev, slave_port, slave_data);
784
785 /* Ensure the UDMA bit is off - it will be turned back on if
786 UDMA is selected */
787
788 if (ap->udma_mask) {
789 pci_read_config_byte(dev, 0x48, &udma_enable);
790 udma_enable &= ~(1 << (2 * ap->port_no + adev->devno));
791 pci_write_config_byte(dev, 0x48, udma_enable);
792 }
793
794 spin_unlock_irqrestore(&piix_lock, flags);
795 }
796
797 /**
798 * do_pata_set_dmamode - Initialize host controller PATA PIO timings
799 * @ap: Port whose timings we are configuring
800 * @adev: Drive in question
801 * @isich: set if the chip is an ICH device
802 *
803 * Set UDMA mode for device, in host controller PCI config space.
804 *
805 * LOCKING:
806 * None (inherited from caller).
807 */
808
809 static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, int isich)
810 {
811 struct pci_dev *dev = to_pci_dev(ap->host->dev);
812 unsigned long flags;
813 u8 master_port = ap->port_no ? 0x42 : 0x40;
814 u16 master_data;
815 u8 speed = adev->dma_mode;
816 int devid = adev->devno + 2 * ap->port_no;
817 u8 udma_enable = 0;
818
819 static const /* ISP RTC */
820 u8 timings[][2] = { { 0, 0 },
821 { 0, 0 },
822 { 1, 0 },
823 { 2, 1 },
824 { 2, 3 }, };
825
826 spin_lock_irqsave(&piix_lock, flags);
827
828 pci_read_config_word(dev, master_port, &master_data);
829 if (ap->udma_mask)
830 pci_read_config_byte(dev, 0x48, &udma_enable);
831
832 if (speed >= XFER_UDMA_0) {
833 unsigned int udma = adev->dma_mode - XFER_UDMA_0;
834 u16 udma_timing;
835 u16 ideconf;
836 int u_clock, u_speed;
837
838 /*
839 * UDMA is handled by a combination of clock switching and
840 * selection of dividers
841 *
842 * Handy rule: Odd modes are UDMATIMx 01, even are 02
843 * except UDMA0 which is 00
844 */
845 u_speed = min(2 - (udma & 1), udma);
846 if (udma == 5)
847 u_clock = 0x1000; /* 100Mhz */
848 else if (udma > 2)
849 u_clock = 1; /* 66Mhz */
850 else
851 u_clock = 0; /* 33Mhz */
852
853 udma_enable |= (1 << devid);
854
855 /* Load the CT/RP selection */
856 pci_read_config_word(dev, 0x4A, &udma_timing);
857 udma_timing &= ~(3 << (4 * devid));
858 udma_timing |= u_speed << (4 * devid);
859 pci_write_config_word(dev, 0x4A, udma_timing);
860
861 if (isich) {
862 /* Select a 33/66/100Mhz clock */
863 pci_read_config_word(dev, 0x54, &ideconf);
864 ideconf &= ~(0x1001 << devid);
865 ideconf |= u_clock << devid;
866 /* For ICH or later we should set bit 10 for better
867 performance (WR_PingPong_En) */
868 pci_write_config_word(dev, 0x54, ideconf);
869 }
870 } else {
871 /*
872 * MWDMA is driven by the PIO timings. We must also enable
873 * IORDY unconditionally along with TIME1. PPE has already
874 * been set when the PIO timing was set.
875 */
876 unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
877 unsigned int control;
878 u8 slave_data;
879 const unsigned int needed_pio[3] = {
880 XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
881 };
882 int pio = needed_pio[mwdma] - XFER_PIO_0;
883
884 control = 3; /* IORDY|TIME1 */
885
886 /* If the drive MWDMA is faster than it can do PIO then
887 we must force PIO into PIO0 */
888
889 if (adev->pio_mode < needed_pio[mwdma])
890 /* Enable DMA timing only */
891 control |= 8; /* PIO cycles in PIO0 */
892
893 if (adev->devno) { /* Slave */
894 master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
895 master_data |= control << 4;
896 pci_read_config_byte(dev, 0x44, &slave_data);
897 slave_data &= (ap->port_no ? 0x0f : 0xf0);
898 /* Load the matching timing */
899 slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
900 pci_write_config_byte(dev, 0x44, slave_data);
901 } else { /* Master */
902 master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY
903 and master timing bits */
904 master_data |= control;
905 master_data |=
906 (timings[pio][0] << 12) |
907 (timings[pio][1] << 8);
908 }
909
910 if (ap->udma_mask)
911 udma_enable &= ~(1 << devid);
912
913 pci_write_config_word(dev, master_port, master_data);
914 }
915 /* Don't scribble on 0x48 if the controller does not support UDMA */
916 if (ap->udma_mask)
917 pci_write_config_byte(dev, 0x48, udma_enable);
918
919 spin_unlock_irqrestore(&piix_lock, flags);
920 }
921
922 /**
923 * piix_set_dmamode - Initialize host controller PATA DMA timings
924 * @ap: Port whose timings we are configuring
925 * @adev: um
926 *
927 * Set MW/UDMA mode for device, in host controller PCI config space.
928 *
929 * LOCKING:
930 * None (inherited from caller).
931 */
932
933 static void piix_set_dmamode(struct ata_port *ap, struct ata_device *adev)
934 {
935 do_pata_set_dmamode(ap, adev, 0);
936 }
937
938 /**
939 * ich_set_dmamode - Initialize host controller PATA DMA timings
940 * @ap: Port whose timings we are configuring
941 * @adev: um
942 *
943 * Set MW/UDMA mode for device, in host controller PCI config space.
944 *
945 * LOCKING:
946 * None (inherited from caller).
947 */
948
949 static void ich_set_dmamode(struct ata_port *ap, struct ata_device *adev)
950 {
951 do_pata_set_dmamode(ap, adev, 1);
952 }
953
954 /*
955 * Serial ATA Index/Data Pair Superset Registers access
956 *
957 * Beginning from ICH8, there's a sane way to access SCRs using index
958 * and data register pair located at BAR5 which means that we have
959 * separate SCRs for master and slave. This is handled using libata
960 * slave_link facility.
961 */
962 static const int piix_sidx_map[] = {
963 [SCR_STATUS] = 0,
964 [SCR_ERROR] = 2,
965 [SCR_CONTROL] = 1,
966 };
967
968 static void piix_sidpr_sel(struct ata_link *link, unsigned int reg)
969 {
970 struct ata_port *ap = link->ap;
971 struct piix_host_priv *hpriv = ap->host->private_data;
972
973 iowrite32(((ap->port_no * 2 + link->pmp) << 8) | piix_sidx_map[reg],
974 hpriv->sidpr + PIIX_SIDPR_IDX);
975 }
976
977 static int piix_sidpr_scr_read(struct ata_link *link,
978 unsigned int reg, u32 *val)
979 {
980 struct piix_host_priv *hpriv = link->ap->host->private_data;
981
982 if (reg >= ARRAY_SIZE(piix_sidx_map))
983 return -EINVAL;
984
985 piix_sidpr_sel(link, reg);
986 *val = ioread32(hpriv->sidpr + PIIX_SIDPR_DATA);
987 return 0;
988 }
989
990 static int piix_sidpr_scr_write(struct ata_link *link,
991 unsigned int reg, u32 val)
992 {
993 struct piix_host_priv *hpriv = link->ap->host->private_data;
994
995 if (reg >= ARRAY_SIZE(piix_sidx_map))
996 return -EINVAL;
997
998 piix_sidpr_sel(link, reg);
999 iowrite32(val, hpriv->sidpr + PIIX_SIDPR_DATA);
1000 return 0;
1001 }
1002
1003 static int piix_sidpr_set_lpm(struct ata_link *link, enum ata_lpm_policy policy,
1004 unsigned hints)
1005 {
1006 return sata_link_scr_lpm(link, policy, false);
1007 }
1008
1009 static bool piix_irq_check(struct ata_port *ap)
1010 {
1011 if (unlikely(!ap->ioaddr.bmdma_addr))
1012 return false;
1013
1014 return ap->ops->bmdma_status(ap) & ATA_DMA_INTR;
1015 }
1016
1017 #ifdef CONFIG_PM
1018 static int piix_broken_suspend(void)
1019 {
1020 static const struct dmi_system_id sysids[] = {
1021 {
1022 .ident = "TECRA M3",
1023 .matches = {
1024 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1025 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M3"),
1026 },
1027 },
1028 {
1029 .ident = "TECRA M3",
1030 .matches = {
1031 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1032 DMI_MATCH(DMI_PRODUCT_NAME, "Tecra M3"),
1033 },
1034 },
1035 {
1036 .ident = "TECRA M4",
1037 .matches = {
1038 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1039 DMI_MATCH(DMI_PRODUCT_NAME, "Tecra M4"),
1040 },
1041 },
1042 {
1043 .ident = "TECRA M4",
1044 .matches = {
1045 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1046 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M4"),
1047 },
1048 },
1049 {
1050 .ident = "TECRA M5",
1051 .matches = {
1052 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1053 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M5"),
1054 },
1055 },
1056 {
1057 .ident = "TECRA M6",
1058 .matches = {
1059 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1060 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M6"),
1061 },
1062 },
1063 {
1064 .ident = "TECRA M7",
1065 .matches = {
1066 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1067 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M7"),
1068 },
1069 },
1070 {
1071 .ident = "TECRA A8",
1072 .matches = {
1073 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1074 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA A8"),
1075 },
1076 },
1077 {
1078 .ident = "Satellite R20",
1079 .matches = {
1080 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1081 DMI_MATCH(DMI_PRODUCT_NAME, "Satellite R20"),
1082 },
1083 },
1084 {
1085 .ident = "Satellite R25",
1086 .matches = {
1087 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1088 DMI_MATCH(DMI_PRODUCT_NAME, "Satellite R25"),
1089 },
1090 },
1091 {
1092 .ident = "Satellite U200",
1093 .matches = {
1094 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1095 DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U200"),
1096 },
1097 },
1098 {
1099 .ident = "Satellite U200",
1100 .matches = {
1101 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1102 DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE U200"),
1103 },
1104 },
1105 {
1106 .ident = "Satellite Pro U200",
1107 .matches = {
1108 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1109 DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE PRO U200"),
1110 },
1111 },
1112 {
1113 .ident = "Satellite U205",
1114 .matches = {
1115 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1116 DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U205"),
1117 },
1118 },
1119 {
1120 .ident = "SATELLITE U205",
1121 .matches = {
1122 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1123 DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE U205"),
1124 },
1125 },
1126 {
1127 .ident = "Portege M500",
1128 .matches = {
1129 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1130 DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE M500"),
1131 },
1132 },
1133 {
1134 .ident = "VGN-BX297XP",
1135 .matches = {
1136 DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
1137 DMI_MATCH(DMI_PRODUCT_NAME, "VGN-BX297XP"),
1138 },
1139 },
1140
1141 { } /* terminate list */
1142 };
1143 static const char *oemstrs[] = {
1144 "Tecra M3,",
1145 };
1146 int i;
1147
1148 if (dmi_check_system(sysids))
1149 return 1;
1150
1151 for (i = 0; i < ARRAY_SIZE(oemstrs); i++)
1152 if (dmi_find_device(DMI_DEV_TYPE_OEM_STRING, oemstrs[i], NULL))
1153 return 1;
1154
1155 /* TECRA M4 sometimes forgets its identify and reports bogus
1156 * DMI information. As the bogus information is a bit
1157 * generic, match as many entries as possible. This manual
1158 * matching is necessary because dmi_system_id.matches is
1159 * limited to four entries.
1160 */
1161 if (dmi_match(DMI_SYS_VENDOR, "TOSHIBA") &&
1162 dmi_match(DMI_PRODUCT_NAME, "000000") &&
1163 dmi_match(DMI_PRODUCT_VERSION, "000000") &&
1164 dmi_match(DMI_PRODUCT_SERIAL, "000000") &&
1165 dmi_match(DMI_BOARD_VENDOR, "TOSHIBA") &&
1166 dmi_match(DMI_BOARD_NAME, "Portable PC") &&
1167 dmi_match(DMI_BOARD_VERSION, "Version A0"))
1168 return 1;
1169
1170 return 0;
1171 }
1172
1173 static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
1174 {
1175 struct ata_host *host = dev_get_drvdata(&pdev->dev);
1176 unsigned long flags;
1177 int rc = 0;
1178
1179 rc = ata_host_suspend(host, mesg);
1180 if (rc)
1181 return rc;
1182
1183 /* Some braindamaged ACPI suspend implementations expect the
1184 * controller to be awake on entry; otherwise, it burns cpu
1185 * cycles and power trying to do something to the sleeping
1186 * beauty.
1187 */
1188 if (piix_broken_suspend() && (mesg.event & PM_EVENT_SLEEP)) {
1189 pci_save_state(pdev);
1190
1191 /* mark its power state as "unknown", since we don't
1192 * know if e.g. the BIOS will change its device state
1193 * when we suspend.
1194 */
1195 if (pdev->current_state == PCI_D0)
1196 pdev->current_state = PCI_UNKNOWN;
1197
1198 /* tell resume that it's waking up from broken suspend */
1199 spin_lock_irqsave(&host->lock, flags);
1200 host->flags |= PIIX_HOST_BROKEN_SUSPEND;
1201 spin_unlock_irqrestore(&host->lock, flags);
1202 } else
1203 ata_pci_device_do_suspend(pdev, mesg);
1204
1205 return 0;
1206 }
1207
1208 static int piix_pci_device_resume(struct pci_dev *pdev)
1209 {
1210 struct ata_host *host = dev_get_drvdata(&pdev->dev);
1211 unsigned long flags;
1212 int rc;
1213
1214 if (host->flags & PIIX_HOST_BROKEN_SUSPEND) {
1215 spin_lock_irqsave(&host->lock, flags);
1216 host->flags &= ~PIIX_HOST_BROKEN_SUSPEND;
1217 spin_unlock_irqrestore(&host->lock, flags);
1218
1219 pci_set_power_state(pdev, PCI_D0);
1220 pci_restore_state(pdev);
1221
1222 /* PCI device wasn't disabled during suspend. Use
1223 * pci_reenable_device() to avoid affecting the enable
1224 * count.
1225 */
1226 rc = pci_reenable_device(pdev);
1227 if (rc)
1228 dev_err(&pdev->dev,
1229 "failed to enable device after resume (%d)\n",
1230 rc);
1231 } else
1232 rc = ata_pci_device_do_resume(pdev);
1233
1234 if (rc == 0)
1235 ata_host_resume(host);
1236
1237 return rc;
1238 }
1239 #endif
1240
1241 static u8 piix_vmw_bmdma_status(struct ata_port *ap)
1242 {
1243 return ata_bmdma_status(ap) & ~ATA_DMA_ERR;
1244 }
1245
1246 #define AHCI_PCI_BAR 5
1247 #define AHCI_GLOBAL_CTL 0x04
1248 #define AHCI_ENABLE (1 << 31)
1249 static int piix_disable_ahci(struct pci_dev *pdev)
1250 {
1251 void __iomem *mmio;
1252 u32 tmp;
1253 int rc = 0;
1254
1255 /* BUG: pci_enable_device has not yet been called. This
1256 * works because this device is usually set up by BIOS.
1257 */
1258
1259 if (!pci_resource_start(pdev, AHCI_PCI_BAR) ||
1260 !pci_resource_len(pdev, AHCI_PCI_BAR))
1261 return 0;
1262
1263 mmio = pci_iomap(pdev, AHCI_PCI_BAR, 64);
1264 if (!mmio)
1265 return -ENOMEM;
1266
1267 tmp = ioread32(mmio + AHCI_GLOBAL_CTL);
1268 if (tmp & AHCI_ENABLE) {
1269 tmp &= ~AHCI_ENABLE;
1270 iowrite32(tmp, mmio + AHCI_GLOBAL_CTL);
1271
1272 tmp = ioread32(mmio + AHCI_GLOBAL_CTL);
1273 if (tmp & AHCI_ENABLE)
1274 rc = -EIO;
1275 }
1276
1277 pci_iounmap(pdev, mmio);
1278 return rc;
1279 }
1280
1281 /**
1282 * piix_check_450nx_errata - Check for problem 450NX setup
1283 * @ata_dev: the PCI device to check
1284 *
1285 * Check for the present of 450NX errata #19 and errata #25. If
1286 * they are found return an error code so we can turn off DMA
1287 */
1288
1289 static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev)
1290 {
1291 struct pci_dev *pdev = NULL;
1292 u16 cfg;
1293 int no_piix_dma = 0;
1294
1295 while ((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL) {
1296 /* Look for 450NX PXB. Check for problem configurations
1297 A PCI quirk checks bit 6 already */
1298 pci_read_config_word(pdev, 0x41, &cfg);
1299 /* Only on the original revision: IDE DMA can hang */
1300 if (pdev->revision == 0x00)
1301 no_piix_dma = 1;
1302 /* On all revisions below 5 PXB bus lock must be disabled for IDE */
1303 else if (cfg & (1<<14) && pdev->revision < 5)
1304 no_piix_dma = 2;
1305 }
1306 if (no_piix_dma)
1307 dev_warn(&ata_dev->dev,
1308 "450NX errata present, disabling IDE DMA%s\n",
1309 no_piix_dma == 2 ? " - a BIOS update may resolve this"
1310 : "");
1311
1312 return no_piix_dma;
1313 }
1314
1315 static void __devinit piix_init_pcs(struct ata_host *host,
1316 const struct piix_map_db *map_db)
1317 {
1318 struct pci_dev *pdev = to_pci_dev(host->dev);
1319 u16 pcs, new_pcs;
1320
1321 pci_read_config_word(pdev, ICH5_PCS, &pcs);
1322
1323 new_pcs = pcs | map_db->port_enable;
1324
1325 if (new_pcs != pcs) {
1326 DPRINTK("updating PCS from 0x%x to 0x%x\n", pcs, new_pcs);
1327 pci_write_config_word(pdev, ICH5_PCS, new_pcs);
1328 msleep(150);
1329 }
1330 }
1331
1332 static const int *__devinit piix_init_sata_map(struct pci_dev *pdev,
1333 struct ata_port_info *pinfo,
1334 const struct piix_map_db *map_db)
1335 {
1336 const int *map;
1337 int i, invalid_map = 0;
1338 u8 map_value;
1339
1340 pci_read_config_byte(pdev, ICH5_PMR, &map_value);
1341
1342 map = map_db->map[map_value & map_db->mask];
1343
1344 dev_info(&pdev->dev, "MAP [");
1345 for (i = 0; i < 4; i++) {
1346 switch (map[i]) {
1347 case RV:
1348 invalid_map = 1;
1349 pr_cont(" XX");
1350 break;
1351
1352 case NA:
1353 pr_cont(" --");
1354 break;
1355
1356 case IDE:
1357 WARN_ON((i & 1) || map[i + 1] != IDE);
1358 pinfo[i / 2] = piix_port_info[ich_pata_100];
1359 i++;
1360 pr_cont(" IDE IDE");
1361 break;
1362
1363 default:
1364 pr_cont(" P%d", map[i]);
1365 if (i & 1)
1366 pinfo[i / 2].flags |= ATA_FLAG_SLAVE_POSS;
1367 break;
1368 }
1369 }
1370 pr_cont(" ]\n");
1371
1372 if (invalid_map)
1373 dev_err(&pdev->dev, "invalid MAP value %u\n", map_value);
1374
1375 return map;
1376 }
1377
1378 static bool piix_no_sidpr(struct ata_host *host)
1379 {
1380 struct pci_dev *pdev = to_pci_dev(host->dev);
1381
1382 /*
1383 * Samsung DB-P70 only has three ATA ports exposed and
1384 * curiously the unconnected first port reports link online
1385 * while not responding to SRST protocol causing excessive
1386 * detection delay.
1387 *
1388 * Unfortunately, the system doesn't carry enough DMI
1389 * information to identify the machine but does have subsystem
1390 * vendor and device set. As it's unclear whether the
1391 * subsystem vendor/device is used only for this specific
1392 * board, the port can't be disabled solely with the
1393 * information; however, turning off SIDPR access works around
1394 * the problem. Turn it off.
1395 *
1396 * This problem is reported in bnc#441240.
1397 *
1398 * https://bugzilla.novell.com/show_bug.cgi?id=441420
1399 */
1400 if (pdev->vendor == PCI_VENDOR_ID_INTEL && pdev->device == 0x2920 &&
1401 pdev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG &&
1402 pdev->subsystem_device == 0xb049) {
1403 dev_warn(host->dev,
1404 "Samsung DB-P70 detected, disabling SIDPR\n");
1405 return true;
1406 }
1407
1408 return false;
1409 }
1410
1411 static int __devinit piix_init_sidpr(struct ata_host *host)
1412 {
1413 struct pci_dev *pdev = to_pci_dev(host->dev);
1414 struct piix_host_priv *hpriv = host->private_data;
1415 struct ata_link *link0 = &host->ports[0]->link;
1416 u32 scontrol;
1417 int i, rc;
1418
1419 /* check for availability */
1420 for (i = 0; i < 4; i++)
1421 if (hpriv->map[i] == IDE)
1422 return 0;
1423
1424 /* is it blacklisted? */
1425 if (piix_no_sidpr(host))
1426 return 0;
1427
1428 if (!(host->ports[0]->flags & PIIX_FLAG_SIDPR))
1429 return 0;
1430
1431 if (pci_resource_start(pdev, PIIX_SIDPR_BAR) == 0 ||
1432 pci_resource_len(pdev, PIIX_SIDPR_BAR) != PIIX_SIDPR_LEN)
1433 return 0;
1434
1435 if (pcim_iomap_regions(pdev, 1 << PIIX_SIDPR_BAR, DRV_NAME))
1436 return 0;
1437
1438 hpriv->sidpr = pcim_iomap_table(pdev)[PIIX_SIDPR_BAR];
1439
1440 /* SCR access via SIDPR doesn't work on some configurations.
1441 * Give it a test drive by inhibiting power save modes which
1442 * we'll do anyway.
1443 */
1444 piix_sidpr_scr_read(link0, SCR_CONTROL, &scontrol);
1445
1446 /* if IPM is already 3, SCR access is probably working. Don't
1447 * un-inhibit power save modes as BIOS might have inhibited
1448 * them for a reason.
1449 */
1450 if ((scontrol & 0xf00) != 0x300) {
1451 scontrol |= 0x300;
1452 piix_sidpr_scr_write(link0, SCR_CONTROL, scontrol);
1453 piix_sidpr_scr_read(link0, SCR_CONTROL, &scontrol);
1454
1455 if ((scontrol & 0xf00) != 0x300) {
1456 dev_info(host->dev,
1457 "SCR access via SIDPR is available but doesn't work\n");
1458 return 0;
1459 }
1460 }
1461
1462 /* okay, SCRs available, set ops and ask libata for slave_link */
1463 for (i = 0; i < 2; i++) {
1464 struct ata_port *ap = host->ports[i];
1465
1466 ap->ops = &piix_sidpr_sata_ops;
1467
1468 if (ap->flags & ATA_FLAG_SLAVE_POSS) {
1469 rc = ata_slave_link_init(ap);
1470 if (rc)
1471 return rc;
1472 }
1473 }
1474
1475 return 0;
1476 }
1477
1478 static void piix_iocfg_bit18_quirk(struct ata_host *host)
1479 {
1480 static const struct dmi_system_id sysids[] = {
1481 {
1482 /* Clevo M570U sets IOCFG bit 18 if the cdrom
1483 * isn't used to boot the system which
1484 * disables the channel.
1485 */
1486 .ident = "M570U",
1487 .matches = {
1488 DMI_MATCH(DMI_SYS_VENDOR, "Clevo Co."),
1489 DMI_MATCH(DMI_PRODUCT_NAME, "M570U"),
1490 },
1491 },
1492
1493 { } /* terminate list */
1494 };
1495 struct pci_dev *pdev = to_pci_dev(host->dev);
1496 struct piix_host_priv *hpriv = host->private_data;
1497
1498 if (!dmi_check_system(sysids))
1499 return;
1500
1501 /* The datasheet says that bit 18 is NOOP but certain systems
1502 * seem to use it to disable a channel. Clear the bit on the
1503 * affected systems.
1504 */
1505 if (hpriv->saved_iocfg & (1 << 18)) {
1506 dev_info(&pdev->dev, "applying IOCFG bit18 quirk\n");
1507 pci_write_config_dword(pdev, PIIX_IOCFG,
1508 hpriv->saved_iocfg & ~(1 << 18));
1509 }
1510 }
1511
1512 static bool piix_broken_system_poweroff(struct pci_dev *pdev)
1513 {
1514 static const struct dmi_system_id broken_systems[] = {
1515 {
1516 .ident = "HP Compaq 2510p",
1517 .matches = {
1518 DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
1519 DMI_MATCH(DMI_PRODUCT_NAME, "HP Compaq 2510p"),
1520 },
1521 /* PCI slot number of the controller */
1522 .driver_data = (void *)0x1FUL,
1523 },
1524 {
1525 .ident = "HP Compaq nc6000",
1526 .matches = {
1527 DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
1528 DMI_MATCH(DMI_PRODUCT_NAME, "HP Compaq nc6000"),
1529 },
1530 /* PCI slot number of the controller */
1531 .driver_data = (void *)0x1FUL,
1532 },
1533
1534 { } /* terminate list */
1535 };
1536 const struct dmi_system_id *dmi = dmi_first_match(broken_systems);
1537
1538 if (dmi) {
1539 unsigned long slot = (unsigned long)dmi->driver_data;
1540 /* apply the quirk only to on-board controllers */
1541 return slot == PCI_SLOT(pdev->devfn);
1542 }
1543
1544 return false;
1545 }
1546
1547 /**
1548 * piix_init_one - Register PIIX ATA PCI device with kernel services
1549 * @pdev: PCI device to register
1550 * @ent: Entry in piix_pci_tbl matching with @pdev
1551 *
1552 * Called from kernel PCI layer. We probe for combined mode (sigh),
1553 * and then hand over control to libata, for it to do the rest.
1554 *
1555 * LOCKING:
1556 * Inherited from PCI layer (may sleep).
1557 *
1558 * RETURNS:
1559 * Zero on success, or -ERRNO value.
1560 */
1561
1562 static int __devinit piix_init_one(struct pci_dev *pdev,
1563 const struct pci_device_id *ent)
1564 {
1565 struct device *dev = &pdev->dev;
1566 struct ata_port_info port_info[2];
1567 const struct ata_port_info *ppi[] = { &port_info[0], &port_info[1] };
1568 struct scsi_host_template *sht = &piix_sht;
1569 unsigned long port_flags;
1570 struct ata_host *host;
1571 struct piix_host_priv *hpriv;
1572 int rc;
1573
1574 ata_print_version_once(&pdev->dev, DRV_VERSION);
1575
1576 /* no hotplugging support for later devices (FIXME) */
1577 if (!in_module_init && ent->driver_data >= ich5_sata)
1578 return -ENODEV;
1579
1580 if (piix_broken_system_poweroff(pdev)) {
1581 piix_port_info[ent->driver_data].flags |=
1582 ATA_FLAG_NO_POWEROFF_SPINDOWN |
1583 ATA_FLAG_NO_HIBERNATE_SPINDOWN;
1584 dev_info(&pdev->dev, "quirky BIOS, skipping spindown "
1585 "on poweroff and hibernation\n");
1586 }
1587
1588 port_info[0] = piix_port_info[ent->driver_data];
1589 port_info[1] = piix_port_info[ent->driver_data];
1590
1591 port_flags = port_info[0].flags;
1592
1593 /* enable device and prepare host */
1594 rc = pcim_enable_device(pdev);
1595 if (rc)
1596 return rc;
1597
1598 hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
1599 if (!hpriv)
1600 return -ENOMEM;
1601
1602 /* Save IOCFG, this will be used for cable detection, quirk
1603 * detection and restoration on detach. This is necessary
1604 * because some ACPI implementations mess up cable related
1605 * bits on _STM. Reported on kernel bz#11879.
1606 */
1607 pci_read_config_dword(pdev, PIIX_IOCFG, &hpriv->saved_iocfg);
1608
1609 /* ICH6R may be driven by either ata_piix or ahci driver
1610 * regardless of BIOS configuration. Make sure AHCI mode is
1611 * off.
1612 */
1613 if (pdev->vendor == PCI_VENDOR_ID_INTEL && pdev->device == 0x2652) {
1614 rc = piix_disable_ahci(pdev);
1615 if (rc)
1616 return rc;
1617 }
1618
1619 /* SATA map init can change port_info, do it before prepping host */
1620 if (port_flags & ATA_FLAG_SATA)
1621 hpriv->map = piix_init_sata_map(pdev, port_info,
1622 piix_map_db_table[ent->driver_data]);
1623
1624 rc = ata_pci_bmdma_prepare_host(pdev, ppi, &host);
1625 if (rc)
1626 return rc;
1627 host->private_data = hpriv;
1628
1629 /* initialize controller */
1630 if (port_flags & ATA_FLAG_SATA) {
1631 piix_init_pcs(host, piix_map_db_table[ent->driver_data]);
1632 rc = piix_init_sidpr(host);
1633 if (rc)
1634 return rc;
1635 if (host->ports[0]->ops == &piix_sidpr_sata_ops)
1636 sht = &piix_sidpr_sht;
1637 }
1638
1639 /* apply IOCFG bit18 quirk */
1640 piix_iocfg_bit18_quirk(host);
1641
1642 /* On ICH5, some BIOSen disable the interrupt using the
1643 * PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3.
1644 * On ICH6, this bit has the same effect, but only when
1645 * MSI is disabled (and it is disabled, as we don't use
1646 * message-signalled interrupts currently).
1647 */
1648 if (port_flags & PIIX_FLAG_CHECKINTR)
1649 pci_intx(pdev, 1);
1650
1651 if (piix_check_450nx_errata(pdev)) {
1652 /* This writes into the master table but it does not
1653 really matter for this errata as we will apply it to
1654 all the PIIX devices on the board */
1655 host->ports[0]->mwdma_mask = 0;
1656 host->ports[0]->udma_mask = 0;
1657 host->ports[1]->mwdma_mask = 0;
1658 host->ports[1]->udma_mask = 0;
1659 }
1660 host->flags |= ATA_HOST_PARALLEL_SCAN;
1661
1662 pci_set_master(pdev);
1663 return ata_pci_sff_activate_host(host, ata_bmdma_interrupt, sht);
1664 }
1665
1666 static void piix_remove_one(struct pci_dev *pdev)
1667 {
1668 struct ata_host *host = dev_get_drvdata(&pdev->dev);
1669 struct piix_host_priv *hpriv = host->private_data;
1670
1671 pci_write_config_dword(pdev, PIIX_IOCFG, hpriv->saved_iocfg);
1672
1673 ata_pci_remove_one(pdev);
1674 }
1675
1676 static int __init piix_init(void)
1677 {
1678 int rc;
1679
1680 DPRINTK("pci_register_driver\n");
1681 rc = pci_register_driver(&piix_pci_driver);
1682 if (rc)
1683 return rc;
1684
1685 in_module_init = 0;
1686
1687 DPRINTK("done\n");
1688 return 0;
1689 }
1690
1691 static void __exit piix_exit(void)
1692 {
1693 pci_unregister_driver(&piix_pci_driver);
1694 }
1695
1696 module_init(piix_init);
1697 module_exit(piix_exit);
Linux Btrfs Development