?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
x86/PCI: use host bridge _CRS info on ASUS M2V-MX SE
[linux-btrfs-devel.git] / drivers / tty / cyclades.c
blobc0e8f2eeb88697b390787d1f210411ae6521c1cd
1 #undef BLOCKMOVE
2 #define Z_WAKE
3 #undef Z_EXT_CHARS_IN_BUFFER
4
5 /*
6 * This file contains the driver for the Cyclades async multiport
7 * serial boards.
8 *
9 * Initially written by Randolph Bentson <bentson@grieg.seaslug.org>.
10 * Modified and maintained by Marcio Saito <marcio@cyclades.com>.
11 *
12 * Copyright (C) 2007-2009 Jiri Slaby <jirislaby@gmail.com>
13 *
14 * Much of the design and some of the code came from serial.c
15 * which was copyright (C) 1991, 1992 Linus Torvalds. It was
16 * extensively rewritten by Theodore Ts'o, 8/16/92 -- 9/14/92,
17 * and then fixed as suggested by Michael K. Johnson 12/12/92.
18 * Converted to pci probing and cleaned up by Jiri Slaby.
19 *
20 */
21
22 #define CY_VERSION "2.6"
23
24 /* If you need to install more boards than NR_CARDS, change the constant
25 in the definition below. No other change is necessary to support up to
26 eight boards. Beyond that you'll have to extend cy_isa_addresses. */
27
28 #define NR_CARDS 4
29
30 /*
31 If the total number of ports is larger than NR_PORTS, change this
32 constant in the definition below. No other change is necessary to
33 support more boards/ports. */
34
35 #define NR_PORTS 256
36
37 #define ZO_V1 0
38 #define ZO_V2 1
39 #define ZE_V1 2
40
41 #define SERIAL_PARANOIA_CHECK
42 #undef CY_DEBUG_OPEN
43 #undef CY_DEBUG_THROTTLE
44 #undef CY_DEBUG_OTHER
45 #undef CY_DEBUG_IO
46 #undef CY_DEBUG_COUNT
47 #undef CY_DEBUG_DTR
48 #undef CY_DEBUG_WAIT_UNTIL_SENT
49 #undef CY_DEBUG_INTERRUPTS
50 #undef CY_16Y_HACK
51 #undef CY_ENABLE_MONITORING
52 #undef CY_PCI_DEBUG
53
54 /*
55 * Include section
56 */
57 #include <linux/module.h>
58 #include <linux/errno.h>
59 #include <linux/signal.h>
60 #include <linux/sched.h>
61 #include <linux/timer.h>
62 #include <linux/interrupt.h>
63 #include <linux/tty.h>
64 #include <linux/tty_flip.h>
65 #include <linux/serial.h>
66 #include <linux/major.h>
67 #include <linux/string.h>
68 #include <linux/fcntl.h>
69 #include <linux/ptrace.h>
70 #include <linux/cyclades.h>
71 #include <linux/mm.h>
72 #include <linux/ioport.h>
73 #include <linux/init.h>
74 #include <linux/delay.h>
75 #include <linux/spinlock.h>
76 #include <linux/bitops.h>
77 #include <linux/firmware.h>
78 #include <linux/device.h>
79 #include <linux/slab.h>
80
81 #include <linux/io.h>
82 #include <linux/uaccess.h>
83
84 #include <linux/kernel.h>
85 #include <linux/pci.h>
86
87 #include <linux/stat.h>
88 #include <linux/proc_fs.h>
89 #include <linux/seq_file.h>
90
91 static void cy_send_xchar(struct tty_struct *tty, char ch);
92
93 #ifndef SERIAL_XMIT_SIZE
94 #define SERIAL_XMIT_SIZE (min(PAGE_SIZE, 4096))
95 #endif
96
97 #define STD_COM_FLAGS (0)
98
99 /* firmware stuff */
100 #define ZL_MAX_BLOCKS 16
101 #define DRIVER_VERSION 0x02010203
102 #define RAM_SIZE 0x80000
103
104 enum zblock_type {
105 ZBLOCK_PRG = 0,
106 ZBLOCK_FPGA = 1
107 };
108
109 struct zfile_header {
110 char name[64];
111 char date[32];
112 char aux[32];
113 u32 n_config;
114 u32 config_offset;
115 u32 n_blocks;
116 u32 block_offset;
117 u32 reserved[9];
118 } __attribute__ ((packed));
119
120 struct zfile_config {
121 char name[64];
122 u32 mailbox;
123 u32 function;
124 u32 n_blocks;
125 u32 block_list[ZL_MAX_BLOCKS];
126 } __attribute__ ((packed));
127
128 struct zfile_block {
129 u32 type;
130 u32 file_offset;
131 u32 ram_offset;
132 u32 size;
133 } __attribute__ ((packed));
134
135 static struct tty_driver *cy_serial_driver;
136
137 #ifdef CONFIG_ISA
138 /* This is the address lookup table. The driver will probe for
139 Cyclom-Y/ISA boards at all addresses in here. If you want the
140 driver to probe addresses at a different address, add it to
141 this table. If the driver is probing some other board and
142 causing problems, remove the offending address from this table.
143 */
144
145 static unsigned int cy_isa_addresses[] = {
146 0xD0000,
147 0xD2000,
148 0xD4000,
149 0xD6000,
150 0xD8000,
151 0xDA000,
152 0xDC000,
153 0xDE000,
154 0, 0, 0, 0, 0, 0, 0, 0
155 };
156
157 #define NR_ISA_ADDRS ARRAY_SIZE(cy_isa_addresses)
158
159 static long maddr[NR_CARDS];
160 static int irq[NR_CARDS];
161
162 module_param_array(maddr, long, NULL, 0);
163 module_param_array(irq, int, NULL, 0);
164
165 #endif /* CONFIG_ISA */
166
167 /* This is the per-card data structure containing address, irq, number of
168 channels, etc. This driver supports a maximum of NR_CARDS cards.
169 */
170 static struct cyclades_card cy_card[NR_CARDS];
171
172 static int cy_next_channel; /* next minor available */
173
174 /*
175 * This is used to look up the divisor speeds and the timeouts
176 * We're normally limited to 15 distinct baud rates. The extra
177 * are accessed via settings in info->port.flags.
178 * 0, 1, 2, 3, 4, 5, 6, 7, 8, 9,
179 * 10, 11, 12, 13, 14, 15, 16, 17, 18, 19,
180 * HI VHI
181 * 20
182 */
183 static const int baud_table[] = {
184 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200,
185 1800, 2400, 4800, 9600, 19200, 38400, 57600, 76800, 115200, 150000,
186 230400, 0
187 };
188
189 static const char baud_co_25[] = { /* 25 MHz clock option table */
190 /* value => 00 01 02 03 04 */
191 /* divide by 8 32 128 512 2048 */
192 0x00, 0x04, 0x04, 0x04, 0x04, 0x04, 0x03, 0x03, 0x03, 0x02,
193 0x02, 0x02, 0x01, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
194 };
195
196 static const char baud_bpr_25[] = { /* 25 MHz baud rate period table */
197 0x00, 0xf5, 0xa3, 0x6f, 0x5c, 0x51, 0xf5, 0xa3, 0x51, 0xa3,
198 0x6d, 0x51, 0xa3, 0x51, 0xa3, 0x51, 0x36, 0x29, 0x1b, 0x15
199 };
200
201 static const char baud_co_60[] = { /* 60 MHz clock option table (CD1400 J) */
202 /* value => 00 01 02 03 04 */
203 /* divide by 8 32 128 512 2048 */
204 0x00, 0x00, 0x00, 0x04, 0x04, 0x04, 0x04, 0x04, 0x03, 0x03,
205 0x03, 0x02, 0x02, 0x01, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00,
206 0x00
207 };
208
209 static const char baud_bpr_60[] = { /* 60 MHz baud rate period table (CD1400 J) */
210 0x00, 0x82, 0x21, 0xff, 0xdb, 0xc3, 0x92, 0x62, 0xc3, 0x62,
211 0x41, 0xc3, 0x62, 0xc3, 0x62, 0xc3, 0x82, 0x62, 0x41, 0x32,
212 0x21
213 };
214
215 static const char baud_cor3[] = { /* receive threshold */
216 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a,
217 0x0a, 0x0a, 0x0a, 0x09, 0x09, 0x08, 0x08, 0x08, 0x08, 0x07,
218 0x07
219 };
220
221 /*
222 * The Cyclades driver implements HW flow control as any serial driver.
223 * The cyclades_port structure member rflow and the vector rflow_thr
224 * allows us to take advantage of a special feature in the CD1400 to avoid
225 * data loss even when the system interrupt latency is too high. These flags
226 * are to be used only with very special applications. Setting these flags
227 * requires the use of a special cable (DTR and RTS reversed). In the new
228 * CD1400-based boards (rev. 6.00 or later), there is no need for special
229 * cables.
230 */
231
232 static const char rflow_thr[] = { /* rflow threshold */
233 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
234 0x00, 0x00, 0x00, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a,
235 0x0a
236 };
237
238 /* The Cyclom-Ye has placed the sequential chips in non-sequential
239 * address order. This look-up table overcomes that problem.
240 */
241 static const unsigned int cy_chip_offset[] = { 0x0000,
242 0x0400,
243 0x0800,
244 0x0C00,
245 0x0200,
246 0x0600,
247 0x0A00,
248 0x0E00
249 };
250
251 /* PCI related definitions */
252
253 #ifdef CONFIG_PCI
254 static const struct pci_device_id cy_pci_dev_id[] = {
255 /* PCI < 1Mb */
256 { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Lo) },
257 /* PCI > 1Mb */
258 { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Hi) },
259 /* 4Y PCI < 1Mb */
260 { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_4Y_Lo) },
261 /* 4Y PCI > 1Mb */
262 { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_4Y_Hi) },
263 /* 8Y PCI < 1Mb */
264 { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_8Y_Lo) },
265 /* 8Y PCI > 1Mb */
266 { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_8Y_Hi) },
267 /* Z PCI < 1Mb */
268 { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Z_Lo) },
269 /* Z PCI > 1Mb */
270 { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Z_Hi) },
271 { } /* end of table */
272 };
273 MODULE_DEVICE_TABLE(pci, cy_pci_dev_id);
274 #endif
275
276 static void cy_start(struct tty_struct *);
277 static void cy_set_line_char(struct cyclades_port *, struct tty_struct *);
278 static int cyz_issue_cmd(struct cyclades_card *, __u32, __u8, __u32);
279 #ifdef CONFIG_ISA
280 static unsigned detect_isa_irq(void __iomem *);
281 #endif /* CONFIG_ISA */
282
283 #ifndef CONFIG_CYZ_INTR
284 static void cyz_poll(unsigned long);
285
286 /* The Cyclades-Z polling cycle is defined by this variable */
287 static long cyz_polling_cycle = CZ_DEF_POLL;
288
289 static DEFINE_TIMER(cyz_timerlist, cyz_poll, 0, 0);
290
291 #else /* CONFIG_CYZ_INTR */
292 static void cyz_rx_restart(unsigned long);
293 static struct timer_list cyz_rx_full_timer[NR_PORTS];
294 #endif /* CONFIG_CYZ_INTR */
295
296 static inline void cyy_writeb(struct cyclades_port *port, u32 reg, u8 val)
297 {
298 struct cyclades_card *card = port->card;
299
300 cy_writeb(port->u.cyy.base_addr + (reg << card->bus_index), val);
301 }
302
303 static inline u8 cyy_readb(struct cyclades_port *port, u32 reg)
304 {
305 struct cyclades_card *card = port->card;
306
307 return readb(port->u.cyy.base_addr + (reg << card->bus_index));
308 }
309
310 static inline bool cy_is_Z(struct cyclades_card *card)
311 {
312 return card->num_chips == (unsigned int)-1;
313 }
314
315 static inline bool __cyz_fpga_loaded(struct RUNTIME_9060 __iomem *ctl_addr)
316 {
317 return readl(&ctl_addr->init_ctrl) & (1 << 17);
318 }
319
320 static inline bool cyz_fpga_loaded(struct cyclades_card *card)
321 {
322 return __cyz_fpga_loaded(card->ctl_addr.p9060);
323 }
324
325 static inline bool cyz_is_loaded(struct cyclades_card *card)
326 {
327 struct FIRM_ID __iomem *fw_id = card->base_addr + ID_ADDRESS;
328
329 return (card->hw_ver == ZO_V1 || cyz_fpga_loaded(card)) &&
330 readl(&fw_id->signature) == ZFIRM_ID;
331 }
332
333 static inline int serial_paranoia_check(struct cyclades_port *info,
334 const char *name, const char *routine)
335 {
336 #ifdef SERIAL_PARANOIA_CHECK
337 if (!info) {
338 printk(KERN_WARNING "cyc Warning: null cyclades_port for (%s) "
339 "in %s\n", name, routine);
340 return 1;
341 }
342
343 if (info->magic != CYCLADES_MAGIC) {
344 printk(KERN_WARNING "cyc Warning: bad magic number for serial "
345 "struct (%s) in %s\n", name, routine);
346 return 1;
347 }
348 #endif
349 return 0;
350 }
351
352 /***********************************************************/
353 /********* Start of block of Cyclom-Y specific code ********/
354
355 /* This routine waits up to 1000 micro-seconds for the previous
356 command to the Cirrus chip to complete and then issues the
357 new command. An error is returned if the previous command
358 didn't finish within the time limit.
359
360 This function is only called from inside spinlock-protected code.
361 */
362 static int __cyy_issue_cmd(void __iomem *base_addr, u8 cmd, int index)
363 {
364 void __iomem *ccr = base_addr + (CyCCR << index);
365 unsigned int i;
366
367 /* Check to see that the previous command has completed */
368 for (i = 0; i < 100; i++) {
369 if (readb(ccr) == 0)
370 break;
371 udelay(10L);
372 }
373 /* if the CCR never cleared, the previous command
374 didn't finish within the "reasonable time" */
375 if (i == 100)
376 return -1;
377
378 /* Issue the new command */
379 cy_writeb(ccr, cmd);
380
381 return 0;
382 }
383
384 static inline int cyy_issue_cmd(struct cyclades_port *port, u8 cmd)
385 {
386 return __cyy_issue_cmd(port->u.cyy.base_addr, cmd,
387 port->card->bus_index);
388 }
389
390 #ifdef CONFIG_ISA
391 /* ISA interrupt detection code */
392 static unsigned detect_isa_irq(void __iomem *address)
393 {
394 int irq;
395 unsigned long irqs, flags;
396 int save_xir, save_car;
397 int index = 0; /* IRQ probing is only for ISA */
398
399 /* forget possible initially masked and pending IRQ */
400 irq = probe_irq_off(probe_irq_on());
401
402 /* Clear interrupts on the board first */
403 cy_writeb(address + (Cy_ClrIntr << index), 0);
404 /* Cy_ClrIntr is 0x1800 */
405
406 irqs = probe_irq_on();
407 /* Wait ... */
408 msleep(5);
409
410 /* Enable the Tx interrupts on the CD1400 */
411 local_irq_save(flags);
412 cy_writeb(address + (CyCAR << index), 0);
413 __cyy_issue_cmd(address, CyCHAN_CTL | CyENB_XMTR, index);
414
415 cy_writeb(address + (CyCAR << index), 0);
416 cy_writeb(address + (CySRER << index),
417 readb(address + (CySRER << index)) | CyTxRdy);
418 local_irq_restore(flags);
419
420 /* Wait ... */
421 msleep(5);
422
423 /* Check which interrupt is in use */
424 irq = probe_irq_off(irqs);
425
426 /* Clean up */
427 save_xir = (u_char) readb(address + (CyTIR << index));
428 save_car = readb(address + (CyCAR << index));
429 cy_writeb(address + (CyCAR << index), (save_xir & 0x3));
430 cy_writeb(address + (CySRER << index),
431 readb(address + (CySRER << index)) & ~CyTxRdy);
432 cy_writeb(address + (CyTIR << index), (save_xir & 0x3f));
433 cy_writeb(address + (CyCAR << index), (save_car));
434 cy_writeb(address + (Cy_ClrIntr << index), 0);
435 /* Cy_ClrIntr is 0x1800 */
436
437 return (irq > 0) ? irq : 0;
438 }
439 #endif /* CONFIG_ISA */
440
441 static void cyy_chip_rx(struct cyclades_card *cinfo, int chip,
442 void __iomem *base_addr)
443 {
444 struct cyclades_port *info;
445 struct tty_struct *tty;
446 int len, index = cinfo->bus_index;
447 u8 ivr, save_xir, channel, save_car, data, char_count;
448
449 #ifdef CY_DEBUG_INTERRUPTS
450 printk(KERN_DEBUG "cyy_interrupt: rcvd intr, chip %d\n", chip);
451 #endif
452 /* determine the channel & change to that context */
453 save_xir = readb(base_addr + (CyRIR << index));
454 channel = save_xir & CyIRChannel;
455 info = &cinfo->ports[channel + chip * 4];
456 save_car = cyy_readb(info, CyCAR);
457 cyy_writeb(info, CyCAR, save_xir);
458 ivr = cyy_readb(info, CyRIVR) & CyIVRMask;
459
460 tty = tty_port_tty_get(&info->port);
461 /* if there is nowhere to put the data, discard it */
462 if (tty == NULL) {
463 if (ivr == CyIVRRxEx) { /* exception */
464 data = cyy_readb(info, CyRDSR);
465 } else { /* normal character reception */
466 char_count = cyy_readb(info, CyRDCR);
467 while (char_count--)
468 data = cyy_readb(info, CyRDSR);
469 }
470 goto end;
471 }
472 /* there is an open port for this data */
473 if (ivr == CyIVRRxEx) { /* exception */
474 data = cyy_readb(info, CyRDSR);
475
476 /* For statistics only */
477 if (data & CyBREAK)
478 info->icount.brk++;
479 else if (data & CyFRAME)
480 info->icount.frame++;
481 else if (data & CyPARITY)
482 info->icount.parity++;
483 else if (data & CyOVERRUN)
484 info->icount.overrun++;
485
486 if (data & info->ignore_status_mask) {
487 info->icount.rx++;
488 tty_kref_put(tty);
489 return;
490 }
491 if (tty_buffer_request_room(tty, 1)) {
492 if (data & info->read_status_mask) {
493 if (data & CyBREAK) {
494 tty_insert_flip_char(tty,
495 cyy_readb(info, CyRDSR),
496 TTY_BREAK);
497 info->icount.rx++;
498 if (info->port.flags & ASYNC_SAK)
499 do_SAK(tty);
500 } else if (data & CyFRAME) {
501 tty_insert_flip_char(tty,
502 cyy_readb(info, CyRDSR),
503 TTY_FRAME);
504 info->icount.rx++;
505 info->idle_stats.frame_errs++;
506 } else if (data & CyPARITY) {
507 /* Pieces of seven... */
508 tty_insert_flip_char(tty,
509 cyy_readb(info, CyRDSR),
510 TTY_PARITY);
511 info->icount.rx++;
512 info->idle_stats.parity_errs++;
513 } else if (data & CyOVERRUN) {
514 tty_insert_flip_char(tty, 0,
515 TTY_OVERRUN);
516 info->icount.rx++;
517 /* If the flip buffer itself is
518 overflowing, we still lose
519 the next incoming character.
520 */
521 tty_insert_flip_char(tty,
522 cyy_readb(info, CyRDSR),
523 TTY_FRAME);
524 info->icount.rx++;
525 info->idle_stats.overruns++;
526 /* These two conditions may imply */
527 /* a normal read should be done. */
528 /* } else if(data & CyTIMEOUT) { */
529 /* } else if(data & CySPECHAR) { */
530 } else {
531 tty_insert_flip_char(tty, 0,
532 TTY_NORMAL);
533 info->icount.rx++;
534 }
535 } else {
536 tty_insert_flip_char(tty, 0, TTY_NORMAL);
537 info->icount.rx++;
538 }
539 } else {
540 /* there was a software buffer overrun and nothing
541 * could be done about it!!! */
542 info->icount.buf_overrun++;
543 info->idle_stats.overruns++;
544 }
545 } else { /* normal character reception */
546 /* load # chars available from the chip */
547 char_count = cyy_readb(info, CyRDCR);
548
549 #ifdef CY_ENABLE_MONITORING
550 ++info->mon.int_count;
551 info->mon.char_count += char_count;
552 if (char_count > info->mon.char_max)
553 info->mon.char_max = char_count;
554 info->mon.char_last = char_count;
555 #endif
556 len = tty_buffer_request_room(tty, char_count);
557 while (len--) {
558 data = cyy_readb(info, CyRDSR);
559 tty_insert_flip_char(tty, data, TTY_NORMAL);
560 info->idle_stats.recv_bytes++;
561 info->icount.rx++;
562 #ifdef CY_16Y_HACK
563 udelay(10L);
564 #endif
565 }
566 info->idle_stats.recv_idle = jiffies;
567 }
568 tty_schedule_flip(tty);
569 tty_kref_put(tty);
570 end:
571 /* end of service */
572 cyy_writeb(info, CyRIR, save_xir & 0x3f);
573 cyy_writeb(info, CyCAR, save_car);
574 }
575
576 static void cyy_chip_tx(struct cyclades_card *cinfo, unsigned int chip,
577 void __iomem *base_addr)
578 {
579 struct cyclades_port *info;
580 struct tty_struct *tty;
581 int char_count, index = cinfo->bus_index;
582 u8 save_xir, channel, save_car, outch;
583
584 /* Since we only get here when the transmit buffer
585 is empty, we know we can always stuff a dozen
586 characters. */
587 #ifdef CY_DEBUG_INTERRUPTS
588 printk(KERN_DEBUG "cyy_interrupt: xmit intr, chip %d\n", chip);
589 #endif
590
591 /* determine the channel & change to that context */
592 save_xir = readb(base_addr + (CyTIR << index));
593 channel = save_xir & CyIRChannel;
594 save_car = readb(base_addr + (CyCAR << index));
595 cy_writeb(base_addr + (CyCAR << index), save_xir);
596
597 info = &cinfo->ports[channel + chip * 4];
598 tty = tty_port_tty_get(&info->port);
599 if (tty == NULL) {
600 cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyTxRdy);
601 goto end;
602 }
603
604 /* load the on-chip space for outbound data */
605 char_count = info->xmit_fifo_size;
606
607 if (info->x_char) { /* send special char */
608 outch = info->x_char;
609 cyy_writeb(info, CyTDR, outch);
610 char_count--;
611 info->icount.tx++;
612 info->x_char = 0;
613 }
614
615 if (info->breakon || info->breakoff) {
616 if (info->breakon) {
617 cyy_writeb(info, CyTDR, 0);
618 cyy_writeb(info, CyTDR, 0x81);
619 info->breakon = 0;
620 char_count -= 2;
621 }
622 if (info->breakoff) {
623 cyy_writeb(info, CyTDR, 0);
624 cyy_writeb(info, CyTDR, 0x83);
625 info->breakoff = 0;
626 char_count -= 2;
627 }
628 }
629
630 while (char_count-- > 0) {
631 if (!info->xmit_cnt) {
632 if (cyy_readb(info, CySRER) & CyTxMpty) {
633 cyy_writeb(info, CySRER,
634 cyy_readb(info, CySRER) & ~CyTxMpty);
635 } else {
636 cyy_writeb(info, CySRER, CyTxMpty |
637 (cyy_readb(info, CySRER) & ~CyTxRdy));
638 }
639 goto done;
640 }
641 if (info->port.xmit_buf == NULL) {
642 cyy_writeb(info, CySRER,
643 cyy_readb(info, CySRER) & ~CyTxRdy);
644 goto done;
645 }
646 if (tty->stopped || tty->hw_stopped) {
647 cyy_writeb(info, CySRER,
648 cyy_readb(info, CySRER) & ~CyTxRdy);
649 goto done;
650 }
651 /* Because the Embedded Transmit Commands have been enabled,
652 * we must check to see if the escape character, NULL, is being
653 * sent. If it is, we must ensure that there is room for it to
654 * be doubled in the output stream. Therefore we no longer
655 * advance the pointer when the character is fetched, but
656 * rather wait until after the check for a NULL output
657 * character. This is necessary because there may not be room
658 * for the two chars needed to send a NULL.)
659 */
660 outch = info->port.xmit_buf[info->xmit_tail];
661 if (outch) {
662 info->xmit_cnt--;
663 info->xmit_tail = (info->xmit_tail + 1) &
664 (SERIAL_XMIT_SIZE - 1);
665 cyy_writeb(info, CyTDR, outch);
666 info->icount.tx++;
667 } else {
668 if (char_count > 1) {
669 info->xmit_cnt--;
670 info->xmit_tail = (info->xmit_tail + 1) &
671 (SERIAL_XMIT_SIZE - 1);
672 cyy_writeb(info, CyTDR, outch);
673 cyy_writeb(info, CyTDR, 0);
674 info->icount.tx++;
675 char_count--;
676 }
677 }
678 }
679
680 done:
681 tty_wakeup(tty);
682 tty_kref_put(tty);
683 end:
684 /* end of service */
685 cyy_writeb(info, CyTIR, save_xir & 0x3f);
686 cyy_writeb(info, CyCAR, save_car);
687 }
688
689 static void cyy_chip_modem(struct cyclades_card *cinfo, int chip,
690 void __iomem *base_addr)
691 {
692 struct cyclades_port *info;
693 struct tty_struct *tty;
694 int index = cinfo->bus_index;
695 u8 save_xir, channel, save_car, mdm_change, mdm_status;
696
697 /* determine the channel & change to that context */
698 save_xir = readb(base_addr + (CyMIR << index));
699 channel = save_xir & CyIRChannel;
700 info = &cinfo->ports[channel + chip * 4];
701 save_car = cyy_readb(info, CyCAR);
702 cyy_writeb(info, CyCAR, save_xir);
703
704 mdm_change = cyy_readb(info, CyMISR);
705 mdm_status = cyy_readb(info, CyMSVR1);
706
707 tty = tty_port_tty_get(&info->port);
708 if (!tty)
709 goto end;
710
711 if (mdm_change & CyANY_DELTA) {
712 /* For statistics only */
713 if (mdm_change & CyDCD)
714 info->icount.dcd++;
715 if (mdm_change & CyCTS)
716 info->icount.cts++;
717 if (mdm_change & CyDSR)
718 info->icount.dsr++;
719 if (mdm_change & CyRI)
720 info->icount.rng++;
721
722 wake_up_interruptible(&info->port.delta_msr_wait);
723 }
724
725 if ((mdm_change & CyDCD) && (info->port.flags & ASYNC_CHECK_CD)) {
726 if (mdm_status & CyDCD)
727 wake_up_interruptible(&info->port.open_wait);
728 else
729 tty_hangup(tty);
730 }
731 if ((mdm_change & CyCTS) && (info->port.flags & ASYNC_CTS_FLOW)) {
732 if (tty->hw_stopped) {
733 if (mdm_status & CyCTS) {
734 /* cy_start isn't used
735 because... !!! */
736 tty->hw_stopped = 0;
737 cyy_writeb(info, CySRER,
738 cyy_readb(info, CySRER) | CyTxRdy);
739 tty_wakeup(tty);
740 }
741 } else {
742 if (!(mdm_status & CyCTS)) {
743 /* cy_stop isn't used
744 because ... !!! */
745 tty->hw_stopped = 1;
746 cyy_writeb(info, CySRER,
747 cyy_readb(info, CySRER) & ~CyTxRdy);
748 }
749 }
750 }
751 /* if (mdm_change & CyDSR) {
752 }
753 if (mdm_change & CyRI) {
754 }*/
755 tty_kref_put(tty);
756 end:
757 /* end of service */
758 cyy_writeb(info, CyMIR, save_xir & 0x3f);
759 cyy_writeb(info, CyCAR, save_car);
760 }
761
762 /* The real interrupt service routine is called
763 whenever the card wants its hand held--chars
764 received, out buffer empty, modem change, etc.
765 */
766 static irqreturn_t cyy_interrupt(int irq, void *dev_id)
767 {
768 int status;
769 struct cyclades_card *cinfo = dev_id;
770 void __iomem *base_addr, *card_base_addr;
771 unsigned int chip, too_many, had_work;
772 int index;
773
774 if (unlikely(cinfo == NULL)) {
775 #ifdef CY_DEBUG_INTERRUPTS
776 printk(KERN_DEBUG "cyy_interrupt: spurious interrupt %d\n",
777 irq);
778 #endif
779 return IRQ_NONE; /* spurious interrupt */
780 }
781
782 card_base_addr = cinfo->base_addr;
783 index = cinfo->bus_index;
784
785 /* card was not initialized yet (e.g. DEBUG_SHIRQ) */
786 if (unlikely(card_base_addr == NULL))
787 return IRQ_HANDLED;
788
789 /* This loop checks all chips in the card. Make a note whenever
790 _any_ chip had some work to do, as this is considered an
791 indication that there will be more to do. Only when no chip
792 has any work does this outermost loop exit.
793 */
794 do {
795 had_work = 0;
796 for (chip = 0; chip < cinfo->num_chips; chip++) {
797 base_addr = cinfo->base_addr +
798 (cy_chip_offset[chip] << index);
799 too_many = 0;
800 while ((status = readb(base_addr +
801 (CySVRR << index))) != 0x00) {
802 had_work++;
803 /* The purpose of the following test is to ensure that
804 no chip can monopolize the driver. This forces the
805 chips to be checked in a round-robin fashion (after
806 draining each of a bunch (1000) of characters).
807 */
808 if (1000 < too_many++)
809 break;
810 spin_lock(&cinfo->card_lock);
811 if (status & CySRReceive) /* rx intr */
812 cyy_chip_rx(cinfo, chip, base_addr);
813 if (status & CySRTransmit) /* tx intr */
814 cyy_chip_tx(cinfo, chip, base_addr);
815 if (status & CySRModem) /* modem intr */
816 cyy_chip_modem(cinfo, chip, base_addr);
817 spin_unlock(&cinfo->card_lock);
818 }
819 }
820 } while (had_work);
821
822 /* clear interrupts */
823 spin_lock(&cinfo->card_lock);
824 cy_writeb(card_base_addr + (Cy_ClrIntr << index), 0);
825 /* Cy_ClrIntr is 0x1800 */
826 spin_unlock(&cinfo->card_lock);
827 return IRQ_HANDLED;
828 } /* cyy_interrupt */
829
830 static void cyy_change_rts_dtr(struct cyclades_port *info, unsigned int set,
831 unsigned int clear)
832 {
833 struct cyclades_card *card = info->card;
834 int channel = info->line - card->first_line;
835 u32 rts, dtr, msvrr, msvrd;
836
837 channel &= 0x03;
838
839 if (info->rtsdtr_inv) {
840 msvrr = CyMSVR2;
841 msvrd = CyMSVR1;
842 rts = CyDTR;
843 dtr = CyRTS;
844 } else {
845 msvrr = CyMSVR1;
846 msvrd = CyMSVR2;
847 rts = CyRTS;
848 dtr = CyDTR;
849 }
850 if (set & TIOCM_RTS) {
851 cyy_writeb(info, CyCAR, channel);
852 cyy_writeb(info, msvrr, rts);
853 }
854 if (clear & TIOCM_RTS) {
855 cyy_writeb(info, CyCAR, channel);
856 cyy_writeb(info, msvrr, ~rts);
857 }
858 if (set & TIOCM_DTR) {
859 cyy_writeb(info, CyCAR, channel);
860 cyy_writeb(info, msvrd, dtr);
861 #ifdef CY_DEBUG_DTR
862 printk(KERN_DEBUG "cyc:set_modem_info raising DTR\n");
863 printk(KERN_DEBUG " status: 0x%x, 0x%x\n",
864 cyy_readb(info, CyMSVR1),
865 cyy_readb(info, CyMSVR2));
866 #endif
867 }
868 if (clear & TIOCM_DTR) {
869 cyy_writeb(info, CyCAR, channel);
870 cyy_writeb(info, msvrd, ~dtr);
871 #ifdef CY_DEBUG_DTR
872 printk(KERN_DEBUG "cyc:set_modem_info dropping DTR\n");
873 printk(KERN_DEBUG " status: 0x%x, 0x%x\n",
874 cyy_readb(info, CyMSVR1),
875 cyy_readb(info, CyMSVR2));
876 #endif
877 }
878 }
879
880 /***********************************************************/
881 /********* End of block of Cyclom-Y specific code **********/
882 /******** Start of block of Cyclades-Z specific code *******/
883 /***********************************************************/
884
885 static int
886 cyz_fetch_msg(struct cyclades_card *cinfo,
887 __u32 *channel, __u8 *cmd, __u32 *param)
888 {
889 struct BOARD_CTRL __iomem *board_ctrl = cinfo->board_ctrl;
890 unsigned long loc_doorbell;
891
892 loc_doorbell = readl(&cinfo->ctl_addr.p9060->loc_doorbell);
893 if (loc_doorbell) {
894 *cmd = (char)(0xff & loc_doorbell);
895 *channel = readl(&board_ctrl->fwcmd_channel);
896 *param = (__u32) readl(&board_ctrl->fwcmd_param);
897 cy_writel(&cinfo->ctl_addr.p9060->loc_doorbell, 0xffffffff);
898 return 1;
899 }
900 return 0;
901 } /* cyz_fetch_msg */
902
903 static int
904 cyz_issue_cmd(struct cyclades_card *cinfo,
905 __u32 channel, __u8 cmd, __u32 param)
906 {
907 struct BOARD_CTRL __iomem *board_ctrl = cinfo->board_ctrl;
908 __u32 __iomem *pci_doorbell;
909 unsigned int index;
910
911 if (!cyz_is_loaded(cinfo))
912 return -1;
913
914 index = 0;
915 pci_doorbell = &cinfo->ctl_addr.p9060->pci_doorbell;
916 while ((readl(pci_doorbell) & 0xff) != 0) {
917 if (index++ == 1000)
918 return (int)(readl(pci_doorbell) & 0xff);
919 udelay(50L);
920 }
921 cy_writel(&board_ctrl->hcmd_channel, channel);
922 cy_writel(&board_ctrl->hcmd_param, param);
923 cy_writel(pci_doorbell, (long)cmd);
924
925 return 0;
926 } /* cyz_issue_cmd */
927
928 static void cyz_handle_rx(struct cyclades_port *info, struct tty_struct *tty)
929 {
930 struct BUF_CTRL __iomem *buf_ctrl = info->u.cyz.buf_ctrl;
931 struct cyclades_card *cinfo = info->card;
932 unsigned int char_count;
933 int len;
934 #ifdef BLOCKMOVE
935 unsigned char *buf;
936 #else
937 char data;
938 #endif
939 __u32 rx_put, rx_get, new_rx_get, rx_bufsize, rx_bufaddr;
940
941 rx_get = new_rx_get = readl(&buf_ctrl->rx_get);
942 rx_put = readl(&buf_ctrl->rx_put);
943 rx_bufsize = readl(&buf_ctrl->rx_bufsize);
944 rx_bufaddr = readl(&buf_ctrl->rx_bufaddr);
945 if (rx_put >= rx_get)
946 char_count = rx_put - rx_get;
947 else
948 char_count = rx_put - rx_get + rx_bufsize;
949
950 if (char_count) {
951 #ifdef CY_ENABLE_MONITORING
952 info->mon.int_count++;
953 info->mon.char_count += char_count;
954 if (char_count > info->mon.char_max)
955 info->mon.char_max = char_count;
956 info->mon.char_last = char_count;
957 #endif
958 if (tty == NULL) {
959 /* flush received characters */
960 new_rx_get = (new_rx_get + char_count) &
961 (rx_bufsize - 1);
962 info->rflush_count++;
963 } else {
964 #ifdef BLOCKMOVE
965 /* we'd like to use memcpy(t, f, n) and memset(s, c, count)
966 for performance, but because of buffer boundaries, there
967 may be several steps to the operation */
968 while (1) {
969 len = tty_prepare_flip_string(tty, &buf,
970 char_count);
971 if (!len)
972 break;
973
974 len = min_t(unsigned int, min(len, char_count),
975 rx_bufsize - new_rx_get);
976
977 memcpy_fromio(buf, cinfo->base_addr +
978 rx_bufaddr + new_rx_get, len);
979
980 new_rx_get = (new_rx_get + len) &
981 (rx_bufsize - 1);
982 char_count -= len;
983 info->icount.rx += len;
984 info->idle_stats.recv_bytes += len;
985 }
986 #else
987 len = tty_buffer_request_room(tty, char_count);
988 while (len--) {
989 data = readb(cinfo->base_addr + rx_bufaddr +
990 new_rx_get);
991 new_rx_get = (new_rx_get + 1) &
992 (rx_bufsize - 1);
993 tty_insert_flip_char(tty, data, TTY_NORMAL);
994 info->idle_stats.recv_bytes++;
995 info->icount.rx++;
996 }
997 #endif
998 #ifdef CONFIG_CYZ_INTR
999 /* Recalculate the number of chars in the RX buffer and issue
1000 a cmd in case it's higher than the RX high water mark */
1001 rx_put = readl(&buf_ctrl->rx_put);
1002 if (rx_put >= rx_get)
1003 char_count = rx_put - rx_get;
1004 else
1005 char_count = rx_put - rx_get + rx_bufsize;
1006 if (char_count >= readl(&buf_ctrl->rx_threshold) &&
1007 !timer_pending(&cyz_rx_full_timer[
1008 info->line]))
1009 mod_timer(&cyz_rx_full_timer[info->line],
1010 jiffies + 1);
1011 #endif
1012 info->idle_stats.recv_idle = jiffies;
1013 tty_schedule_flip(tty);
1014 }
1015 /* Update rx_get */
1016 cy_writel(&buf_ctrl->rx_get, new_rx_get);
1017 }
1018 }
1019
1020 static void cyz_handle_tx(struct cyclades_port *info, struct tty_struct *tty)
1021 {
1022 struct BUF_CTRL __iomem *buf_ctrl = info->u.cyz.buf_ctrl;
1023 struct cyclades_card *cinfo = info->card;
1024 u8 data;
1025 unsigned int char_count;
1026 #ifdef BLOCKMOVE
1027 int small_count;
1028 #endif
1029 __u32 tx_put, tx_get, tx_bufsize, tx_bufaddr;
1030
1031 if (info->xmit_cnt <= 0) /* Nothing to transmit */
1032 return;
1033
1034 tx_get = readl(&buf_ctrl->tx_get);
1035 tx_put = readl(&buf_ctrl->tx_put);
1036 tx_bufsize = readl(&buf_ctrl->tx_bufsize);
1037 tx_bufaddr = readl(&buf_ctrl->tx_bufaddr);
1038 if (tx_put >= tx_get)
1039 char_count = tx_get - tx_put - 1 + tx_bufsize;
1040 else
1041 char_count = tx_get - tx_put - 1;
1042
1043 if (char_count) {
1044
1045 if (tty == NULL)
1046 goto ztxdone;
1047
1048 if (info->x_char) { /* send special char */
1049 data = info->x_char;
1050
1051 cy_writeb(cinfo->base_addr + tx_bufaddr + tx_put, data);
1052 tx_put = (tx_put + 1) & (tx_bufsize - 1);
1053 info->x_char = 0;
1054 char_count--;
1055 info->icount.tx++;
1056 }
1057 #ifdef BLOCKMOVE
1058 while (0 < (small_count = min_t(unsigned int,
1059 tx_bufsize - tx_put, min_t(unsigned int,
1060 (SERIAL_XMIT_SIZE - info->xmit_tail),
1061 min_t(unsigned int, info->xmit_cnt,
1062 char_count))))) {
1063
1064 memcpy_toio((char *)(cinfo->base_addr + tx_bufaddr +
1065 tx_put),
1066 &info->port.xmit_buf[info->xmit_tail],
1067 small_count);
1068
1069 tx_put = (tx_put + small_count) & (tx_bufsize - 1);
1070 char_count -= small_count;
1071 info->icount.tx += small_count;
1072 info->xmit_cnt -= small_count;
1073 info->xmit_tail = (info->xmit_tail + small_count) &
1074 (SERIAL_XMIT_SIZE - 1);
1075 }
1076 #else
1077 while (info->xmit_cnt && char_count) {
1078 data = info->port.xmit_buf[info->xmit_tail];
1079 info->xmit_cnt--;
1080 info->xmit_tail = (info->xmit_tail + 1) &
1081 (SERIAL_XMIT_SIZE - 1);
1082
1083 cy_writeb(cinfo->base_addr + tx_bufaddr + tx_put, data);
1084 tx_put = (tx_put + 1) & (tx_bufsize - 1);
1085 char_count--;
1086 info->icount.tx++;
1087 }
1088 #endif
1089 tty_wakeup(tty);
1090 ztxdone:
1091 /* Update tx_put */
1092 cy_writel(&buf_ctrl->tx_put, tx_put);
1093 }
1094 }
1095
1096 static void cyz_handle_cmd(struct cyclades_card *cinfo)
1097 {
1098 struct BOARD_CTRL __iomem *board_ctrl = cinfo->board_ctrl;
1099 struct tty_struct *tty;
1100 struct cyclades_port *info;
1101 __u32 channel, param, fw_ver;
1102 __u8 cmd;
1103 int special_count;
1104 int delta_count;
1105
1106 fw_ver = readl(&board_ctrl->fw_version);
1107
1108 while (cyz_fetch_msg(cinfo, &channel, &cmd, &param) == 1) {
1109 special_count = 0;
1110 delta_count = 0;
1111 info = &cinfo->ports[channel];
1112 tty = tty_port_tty_get(&info->port);
1113 if (tty == NULL)
1114 continue;
1115
1116 switch (cmd) {
1117 case C_CM_PR_ERROR:
1118 tty_insert_flip_char(tty, 0, TTY_PARITY);
1119 info->icount.rx++;
1120 special_count++;
1121 break;
1122 case C_CM_FR_ERROR:
1123 tty_insert_flip_char(tty, 0, TTY_FRAME);
1124 info->icount.rx++;
1125 special_count++;
1126 break;
1127 case C_CM_RXBRK:
1128 tty_insert_flip_char(tty, 0, TTY_BREAK);
1129 info->icount.rx++;
1130 special_count++;
1131 break;
1132 case C_CM_MDCD:
1133 info->icount.dcd++;
1134 delta_count++;
1135 if (info->port.flags & ASYNC_CHECK_CD) {
1136 u32 dcd = fw_ver > 241 ? param :
1137 readl(&info->u.cyz.ch_ctrl->rs_status);
1138 if (dcd & C_RS_DCD)
1139 wake_up_interruptible(&info->port.open_wait);
1140 else
1141 tty_hangup(tty);
1142 }
1143 break;
1144 case C_CM_MCTS:
1145 info->icount.cts++;
1146 delta_count++;
1147 break;
1148 case C_CM_MRI:
1149 info->icount.rng++;
1150 delta_count++;
1151 break;
1152 case C_CM_MDSR:
1153 info->icount.dsr++;
1154 delta_count++;
1155 break;
1156 #ifdef Z_WAKE
1157 case C_CM_IOCTLW:
1158 complete(&info->shutdown_wait);
1159 break;
1160 #endif
1161 #ifdef CONFIG_CYZ_INTR
1162 case C_CM_RXHIWM:
1163 case C_CM_RXNNDT:
1164 case C_CM_INTBACK2:
1165 /* Reception Interrupt */
1166 #ifdef CY_DEBUG_INTERRUPTS
1167 printk(KERN_DEBUG "cyz_interrupt: rcvd intr, card %d, "
1168 "port %ld\n", info->card, channel);
1169 #endif
1170 cyz_handle_rx(info, tty);
1171 break;
1172 case C_CM_TXBEMPTY:
1173 case C_CM_TXLOWWM:
1174 case C_CM_INTBACK:
1175 /* Transmission Interrupt */
1176 #ifdef CY_DEBUG_INTERRUPTS
1177 printk(KERN_DEBUG "cyz_interrupt: xmit intr, card %d, "
1178 "port %ld\n", info->card, channel);
1179 #endif
1180 cyz_handle_tx(info, tty);
1181 break;
1182 #endif /* CONFIG_CYZ_INTR */
1183 case C_CM_FATAL:
1184 /* should do something with this !!! */
1185 break;
1186 default:
1187 break;
1188 }
1189 if (delta_count)
1190 wake_up_interruptible(&info->port.delta_msr_wait);
1191 if (special_count)
1192 tty_schedule_flip(tty);
1193 tty_kref_put(tty);
1194 }
1195 }
1196
1197 #ifdef CONFIG_CYZ_INTR
1198 static irqreturn_t cyz_interrupt(int irq, void *dev_id)
1199 {
1200 struct cyclades_card *cinfo = dev_id;
1201
1202 if (unlikely(!cyz_is_loaded(cinfo))) {
1203 #ifdef CY_DEBUG_INTERRUPTS
1204 printk(KERN_DEBUG "cyz_interrupt: board not yet loaded "
1205 "(IRQ%d).\n", irq);
1206 #endif
1207 return IRQ_NONE;
1208 }
1209
1210 /* Handle the interrupts */
1211 cyz_handle_cmd(cinfo);
1212
1213 return IRQ_HANDLED;
1214 } /* cyz_interrupt */
1215
1216 static void cyz_rx_restart(unsigned long arg)
1217 {
1218 struct cyclades_port *info = (struct cyclades_port *)arg;
1219 struct cyclades_card *card = info->card;
1220 int retval;
1221 __u32 channel = info->line - card->first_line;
1222 unsigned long flags;
1223
1224 spin_lock_irqsave(&card->card_lock, flags);
1225 retval = cyz_issue_cmd(card, channel, C_CM_INTBACK2, 0L);
1226 if (retval != 0) {
1227 printk(KERN_ERR "cyc:cyz_rx_restart retval on ttyC%d was %x\n",
1228 info->line, retval);
1229 }
1230 spin_unlock_irqrestore(&card->card_lock, flags);
1231 }
1232
1233 #else /* CONFIG_CYZ_INTR */
1234
1235 static void cyz_poll(unsigned long arg)
1236 {
1237 struct cyclades_card *cinfo;
1238 struct cyclades_port *info;
1239 unsigned long expires = jiffies + HZ;
1240 unsigned int port, card;
1241
1242 for (card = 0; card < NR_CARDS; card++) {
1243 cinfo = &cy_card[card];
1244
1245 if (!cy_is_Z(cinfo))
1246 continue;
1247 if (!cyz_is_loaded(cinfo))
1248 continue;
1249
1250 /* Skip first polling cycle to avoid racing conditions with the FW */
1251 if (!cinfo->intr_enabled) {
1252 cinfo->intr_enabled = 1;
1253 continue;
1254 }
1255
1256 cyz_handle_cmd(cinfo);
1257
1258 for (port = 0; port < cinfo->nports; port++) {
1259 struct tty_struct *tty;
1260
1261 info = &cinfo->ports[port];
1262 tty = tty_port_tty_get(&info->port);
1263 /* OK to pass NULL to the handle functions below.
1264 They need to drop the data in that case. */
1265
1266 if (!info->throttle)
1267 cyz_handle_rx(info, tty);
1268 cyz_handle_tx(info, tty);
1269 tty_kref_put(tty);
1270 }
1271 /* poll every 'cyz_polling_cycle' period */
1272 expires = jiffies + cyz_polling_cycle;
1273 }
1274 mod_timer(&cyz_timerlist, expires);
1275 } /* cyz_poll */
1276
1277 #endif /* CONFIG_CYZ_INTR */
1278
1279 /********** End of block of Cyclades-Z specific code *********/
1280 /***********************************************************/
1281
1282 /* This is called whenever a port becomes active;
1283 interrupts are enabled and DTR & RTS are turned on.
1284 */
1285 static int cy_startup(struct cyclades_port *info, struct tty_struct *tty)
1286 {
1287 struct cyclades_card *card;
1288 unsigned long flags;
1289 int retval = 0;
1290 int channel;
1291 unsigned long page;
1292
1293 card = info->card;
1294 channel = info->line - card->first_line;
1295
1296 page = get_zeroed_page(GFP_KERNEL);
1297 if (!page)
1298 return -ENOMEM;
1299
1300 spin_lock_irqsave(&card->card_lock, flags);
1301
1302 if (info->port.flags & ASYNC_INITIALIZED)
1303 goto errout;
1304
1305 if (!info->type) {
1306 set_bit(TTY_IO_ERROR, &tty->flags);
1307 goto errout;
1308 }
1309
1310 if (info->port.xmit_buf)
1311 free_page(page);
1312 else
1313 info->port.xmit_buf = (unsigned char *)page;
1314
1315 spin_unlock_irqrestore(&card->card_lock, flags);
1316
1317 cy_set_line_char(info, tty);
1318
1319 if (!cy_is_Z(card)) {
1320 channel &= 0x03;
1321
1322 spin_lock_irqsave(&card->card_lock, flags);
1323
1324 cyy_writeb(info, CyCAR, channel);
1325
1326 cyy_writeb(info, CyRTPR,
1327 (info->default_timeout ? info->default_timeout : 0x02));
1328 /* 10ms rx timeout */
1329
1330 cyy_issue_cmd(info, CyCHAN_CTL | CyENB_RCVR | CyENB_XMTR);
1331
1332 cyy_change_rts_dtr(info, TIOCM_RTS | TIOCM_DTR, 0);
1333
1334 cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyRxData);
1335 } else {
1336 struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl;
1337
1338 if (!cyz_is_loaded(card))
1339 return -ENODEV;
1340
1341 #ifdef CY_DEBUG_OPEN
1342 printk(KERN_DEBUG "cyc startup Z card %d, channel %d, "
1343 "base_addr %p\n", card, channel, card->base_addr);
1344 #endif
1345 spin_lock_irqsave(&card->card_lock, flags);
1346
1347 cy_writel(&ch_ctrl->op_mode, C_CH_ENABLE);
1348 #ifdef Z_WAKE
1349 #ifdef CONFIG_CYZ_INTR
1350 cy_writel(&ch_ctrl->intr_enable,
1351 C_IN_TXBEMPTY | C_IN_TXLOWWM | C_IN_RXHIWM |
1352 C_IN_RXNNDT | C_IN_IOCTLW | C_IN_MDCD);
1353 #else
1354 cy_writel(&ch_ctrl->intr_enable,
1355 C_IN_IOCTLW | C_IN_MDCD);
1356 #endif /* CONFIG_CYZ_INTR */
1357 #else
1358 #ifdef CONFIG_CYZ_INTR
1359 cy_writel(&ch_ctrl->intr_enable,
1360 C_IN_TXBEMPTY | C_IN_TXLOWWM | C_IN_RXHIWM |
1361 C_IN_RXNNDT | C_IN_MDCD);
1362 #else
1363 cy_writel(&ch_ctrl->intr_enable, C_IN_MDCD);
1364 #endif /* CONFIG_CYZ_INTR */
1365 #endif /* Z_WAKE */
1366
1367 retval = cyz_issue_cmd(card, channel, C_CM_IOCTL, 0L);
1368 if (retval != 0) {
1369 printk(KERN_ERR "cyc:startup(1) retval on ttyC%d was "
1370 "%x\n", info->line, retval);
1371 }
1372
1373 /* Flush RX buffers before raising DTR and RTS */
1374 retval = cyz_issue_cmd(card, channel, C_CM_FLUSH_RX, 0L);
1375 if (retval != 0) {
1376 printk(KERN_ERR "cyc:startup(2) retval on ttyC%d was "
1377 "%x\n", info->line, retval);
1378 }
1379
1380 /* set timeout !!! */
1381 /* set RTS and DTR !!! */
1382 tty_port_raise_dtr_rts(&info->port);
1383
1384 /* enable send, recv, modem !!! */
1385 }
1386
1387 info->port.flags |= ASYNC_INITIALIZED;
1388
1389 clear_bit(TTY_IO_ERROR, &tty->flags);
1390 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1391 info->breakon = info->breakoff = 0;
1392 memset((char *)&info->idle_stats, 0, sizeof(info->idle_stats));
1393 info->idle_stats.in_use =
1394 info->idle_stats.recv_idle =
1395 info->idle_stats.xmit_idle = jiffies;
1396
1397 spin_unlock_irqrestore(&card->card_lock, flags);
1398
1399 #ifdef CY_DEBUG_OPEN
1400 printk(KERN_DEBUG "cyc startup done\n");
1401 #endif
1402 return 0;
1403
1404 errout:
1405 spin_unlock_irqrestore(&card->card_lock, flags);
1406 free_page(page);
1407 return retval;
1408 } /* startup */
1409
1410 static void start_xmit(struct cyclades_port *info)
1411 {
1412 struct cyclades_card *card = info->card;
1413 unsigned long flags;
1414 int channel = info->line - card->first_line;
1415
1416 if (!cy_is_Z(card)) {
1417 spin_lock_irqsave(&card->card_lock, flags);
1418 cyy_writeb(info, CyCAR, channel & 0x03);
1419 cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyTxRdy);
1420 spin_unlock_irqrestore(&card->card_lock, flags);
1421 } else {
1422 #ifdef CONFIG_CYZ_INTR
1423 int retval;
1424
1425 spin_lock_irqsave(&card->card_lock, flags);
1426 retval = cyz_issue_cmd(card, channel, C_CM_INTBACK, 0L);
1427 if (retval != 0) {
1428 printk(KERN_ERR "cyc:start_xmit retval on ttyC%d was "
1429 "%x\n", info->line, retval);
1430 }
1431 spin_unlock_irqrestore(&card->card_lock, flags);
1432 #else /* CONFIG_CYZ_INTR */
1433 /* Don't have to do anything at this time */
1434 #endif /* CONFIG_CYZ_INTR */
1435 }
1436 } /* start_xmit */
1437
1438 /*
1439 * This routine shuts down a serial port; interrupts are disabled,
1440 * and DTR is dropped if the hangup on close termio flag is on.
1441 */
1442 static void cy_shutdown(struct cyclades_port *info, struct tty_struct *tty)
1443 {
1444 struct cyclades_card *card;
1445 unsigned long flags;
1446
1447 if (!(info->port.flags & ASYNC_INITIALIZED))
1448 return;
1449
1450 card = info->card;
1451 if (!cy_is_Z(card)) {
1452 spin_lock_irqsave(&card->card_lock, flags);
1453
1454 /* Clear delta_msr_wait queue to avoid mem leaks. */
1455 wake_up_interruptible(&info->port.delta_msr_wait);
1456
1457 if (info->port.xmit_buf) {
1458 unsigned char *temp;
1459 temp = info->port.xmit_buf;
1460 info->port.xmit_buf = NULL;
1461 free_page((unsigned long)temp);
1462 }
1463 if (tty->termios->c_cflag & HUPCL)
1464 cyy_change_rts_dtr(info, 0, TIOCM_RTS | TIOCM_DTR);
1465
1466 cyy_issue_cmd(info, CyCHAN_CTL | CyDIS_RCVR);
1467 /* it may be appropriate to clear _XMIT at
1468 some later date (after testing)!!! */
1469
1470 set_bit(TTY_IO_ERROR, &tty->flags);
1471 info->port.flags &= ~ASYNC_INITIALIZED;
1472 spin_unlock_irqrestore(&card->card_lock, flags);
1473 } else {
1474 #ifdef CY_DEBUG_OPEN
1475 int channel = info->line - card->first_line;
1476 printk(KERN_DEBUG "cyc shutdown Z card %d, channel %d, "
1477 "base_addr %p\n", card, channel, card->base_addr);
1478 #endif
1479
1480 if (!cyz_is_loaded(card))
1481 return;
1482
1483 spin_lock_irqsave(&card->card_lock, flags);
1484
1485 if (info->port.xmit_buf) {
1486 unsigned char *temp;
1487 temp = info->port.xmit_buf;
1488 info->port.xmit_buf = NULL;
1489 free_page((unsigned long)temp);
1490 }
1491
1492 if (tty->termios->c_cflag & HUPCL)
1493 tty_port_lower_dtr_rts(&info->port);
1494
1495 set_bit(TTY_IO_ERROR, &tty->flags);
1496 info->port.flags &= ~ASYNC_INITIALIZED;
1497
1498 spin_unlock_irqrestore(&card->card_lock, flags);
1499 }
1500
1501 #ifdef CY_DEBUG_OPEN
1502 printk(KERN_DEBUG "cyc shutdown done\n");
1503 #endif
1504 } /* shutdown */
1505
1506 /*
1507 * ------------------------------------------------------------
1508 * cy_open() and friends
1509 * ------------------------------------------------------------
1510 */
1511
1512 /*
1513 * This routine is called whenever a serial port is opened. It
1514 * performs the serial-specific initialization for the tty structure.
1515 */
1516 static int cy_open(struct tty_struct *tty, struct file *filp)
1517 {
1518 struct cyclades_port *info;
1519 unsigned int i, line;
1520 int retval;
1521
1522 line = tty->index;
1523 if (tty->index < 0 || NR_PORTS <= line)
1524 return -ENODEV;
1525
1526 for (i = 0; i < NR_CARDS; i++)
1527 if (line < cy_card[i].first_line + cy_card[i].nports &&
1528 line >= cy_card[i].first_line)
1529 break;
1530 if (i >= NR_CARDS)
1531 return -ENODEV;
1532 info = &cy_card[i].ports[line - cy_card[i].first_line];
1533 if (info->line < 0)
1534 return -ENODEV;
1535
1536 /* If the card's firmware hasn't been loaded,
1537 treat it as absent from the system. This
1538 will make the user pay attention.
1539 */
1540 if (cy_is_Z(info->card)) {
1541 struct cyclades_card *cinfo = info->card;
1542 struct FIRM_ID __iomem *firm_id = cinfo->base_addr + ID_ADDRESS;
1543
1544 if (!cyz_is_loaded(cinfo)) {
1545 if (cinfo->hw_ver == ZE_V1 && cyz_fpga_loaded(cinfo) &&
1546 readl(&firm_id->signature) ==
1547 ZFIRM_HLT) {
1548 printk(KERN_ERR "cyc:Cyclades-Z Error: you "
1549 "need an external power supply for "
1550 "this number of ports.\nFirmware "
1551 "halted.\n");
1552 } else {
1553 printk(KERN_ERR "cyc:Cyclades-Z firmware not "
1554 "yet loaded\n");
1555 }
1556 return -ENODEV;
1557 }
1558 #ifdef CONFIG_CYZ_INTR
1559 else {
1560 /* In case this Z board is operating in interrupt mode, its
1561 interrupts should be enabled as soon as the first open
1562 happens to one of its ports. */
1563 if (!cinfo->intr_enabled) {
1564 u16 intr;
1565
1566 /* Enable interrupts on the PLX chip */
1567 intr = readw(&cinfo->ctl_addr.p9060->
1568 intr_ctrl_stat) | 0x0900;
1569 cy_writew(&cinfo->ctl_addr.p9060->
1570 intr_ctrl_stat, intr);
1571 /* Enable interrupts on the FW */
1572 retval = cyz_issue_cmd(cinfo, 0,
1573 C_CM_IRQ_ENBL, 0L);
1574 if (retval != 0) {
1575 printk(KERN_ERR "cyc:IRQ enable retval "
1576 "was %x\n", retval);
1577 }
1578 cinfo->intr_enabled = 1;
1579 }
1580 }
1581 #endif /* CONFIG_CYZ_INTR */
1582 /* Make sure this Z port really exists in hardware */
1583 if (info->line > (cinfo->first_line + cinfo->nports - 1))
1584 return -ENODEV;
1585 }
1586 #ifdef CY_DEBUG_OTHER
1587 printk(KERN_DEBUG "cyc:cy_open ttyC%d\n", info->line);
1588 #endif
1589 tty->driver_data = info;
1590 if (serial_paranoia_check(info, tty->name, "cy_open"))
1591 return -ENODEV;
1592
1593 #ifdef CY_DEBUG_OPEN
1594 printk(KERN_DEBUG "cyc:cy_open ttyC%d, count = %d\n", info->line,
1595 info->port.count);
1596 #endif
1597 info->port.count++;
1598 #ifdef CY_DEBUG_COUNT
1599 printk(KERN_DEBUG "cyc:cy_open (%d): incrementing count to %d\n",
1600 current->pid, info->port.count);
1601 #endif
1602
1603 /*
1604 * If the port is the middle of closing, bail out now
1605 */
1606 if (tty_hung_up_p(filp) || (info->port.flags & ASYNC_CLOSING)) {
1607 wait_event_interruptible_tty(info->port.close_wait,
1608 !(info->port.flags & ASYNC_CLOSING));
1609 return (info->port.flags & ASYNC_HUP_NOTIFY) ? -EAGAIN: -ERESTARTSYS;
1610 }
1611
1612 /*
1613 * Start up serial port
1614 */
1615 retval = cy_startup(info, tty);
1616 if (retval)
1617 return retval;
1618
1619 retval = tty_port_block_til_ready(&info->port, tty, filp);
1620 if (retval) {
1621 #ifdef CY_DEBUG_OPEN
1622 printk(KERN_DEBUG "cyc:cy_open returning after block_til_ready "
1623 "with %d\n", retval);
1624 #endif
1625 return retval;
1626 }
1627
1628 info->throttle = 0;
1629 tty_port_tty_set(&info->port, tty);
1630
1631 #ifdef CY_DEBUG_OPEN
1632 printk(KERN_DEBUG "cyc:cy_open done\n");
1633 #endif
1634 return 0;
1635 } /* cy_open */
1636
1637 /*
1638 * cy_wait_until_sent() --- wait until the transmitter is empty
1639 */
1640 static void cy_wait_until_sent(struct tty_struct *tty, int timeout)
1641 {
1642 struct cyclades_card *card;
1643 struct cyclades_port *info = tty->driver_data;
1644 unsigned long orig_jiffies;
1645 int char_time;
1646
1647 if (serial_paranoia_check(info, tty->name, "cy_wait_until_sent"))
1648 return;
1649
1650 if (info->xmit_fifo_size == 0)
1651 return; /* Just in case.... */
1652
1653 orig_jiffies = jiffies;
1654 /*
1655 * Set the check interval to be 1/5 of the estimated time to
1656 * send a single character, and make it at least 1. The check
1657 * interval should also be less than the timeout.
1658 *
1659 * Note: we have to use pretty tight timings here to satisfy
1660 * the NIST-PCTS.
1661 */
1662 char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size;
1663 char_time = char_time / 5;
1664 if (char_time <= 0)
1665 char_time = 1;
1666 if (timeout < 0)
1667 timeout = 0;
1668 if (timeout)
1669 char_time = min(char_time, timeout);
1670 /*
1671 * If the transmitter hasn't cleared in twice the approximate
1672 * amount of time to send the entire FIFO, it probably won't
1673 * ever clear. This assumes the UART isn't doing flow
1674 * control, which is currently the case. Hence, if it ever
1675 * takes longer than info->timeout, this is probably due to a
1676 * UART bug of some kind. So, we clamp the timeout parameter at
1677 * 2*info->timeout.
1678 */
1679 if (!timeout || timeout > 2 * info->timeout)
1680 timeout = 2 * info->timeout;
1681 #ifdef CY_DEBUG_WAIT_UNTIL_SENT
1682 printk(KERN_DEBUG "In cy_wait_until_sent(%d) check=%d, jiff=%lu...",
1683 timeout, char_time, jiffies);
1684 #endif
1685 card = info->card;
1686 if (!cy_is_Z(card)) {
1687 while (cyy_readb(info, CySRER) & CyTxRdy) {
1688 #ifdef CY_DEBUG_WAIT_UNTIL_SENT
1689 printk(KERN_DEBUG "Not clean (jiff=%lu)...", jiffies);
1690 #endif
1691 if (msleep_interruptible(jiffies_to_msecs(char_time)))
1692 break;
1693 if (timeout && time_after(jiffies, orig_jiffies +
1694 timeout))
1695 break;
1696 }
1697 }
1698 /* Run one more char cycle */
1699 msleep_interruptible(jiffies_to_msecs(char_time * 5));
1700 #ifdef CY_DEBUG_WAIT_UNTIL_SENT
1701 printk(KERN_DEBUG "Clean (jiff=%lu)...done\n", jiffies);
1702 #endif
1703 }
1704
1705 static void cy_flush_buffer(struct tty_struct *tty)
1706 {
1707 struct cyclades_port *info = tty->driver_data;
1708 struct cyclades_card *card;
1709 int channel, retval;
1710 unsigned long flags;
1711
1712 #ifdef CY_DEBUG_IO
1713 printk(KERN_DEBUG "cyc:cy_flush_buffer ttyC%d\n", info->line);
1714 #endif
1715
1716 if (serial_paranoia_check(info, tty->name, "cy_flush_buffer"))
1717 return;
1718
1719 card = info->card;
1720 channel = info->line - card->first_line;
1721
1722 spin_lock_irqsave(&card->card_lock, flags);
1723 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1724 spin_unlock_irqrestore(&card->card_lock, flags);
1725
1726 if (cy_is_Z(card)) { /* If it is a Z card, flush the on-board
1727 buffers as well */
1728 spin_lock_irqsave(&card->card_lock, flags);
1729 retval = cyz_issue_cmd(card, channel, C_CM_FLUSH_TX, 0L);
1730 if (retval != 0) {
1731 printk(KERN_ERR "cyc: flush_buffer retval on ttyC%d "
1732 "was %x\n", info->line, retval);
1733 }
1734 spin_unlock_irqrestore(&card->card_lock, flags);
1735 }
1736 tty_wakeup(tty);
1737 } /* cy_flush_buffer */
1738
1739
1740 static void cy_do_close(struct tty_port *port)
1741 {
1742 struct cyclades_port *info = container_of(port, struct cyclades_port,
1743 port);
1744 struct cyclades_card *card;
1745 unsigned long flags;
1746 int channel;
1747
1748 card = info->card;
1749 channel = info->line - card->first_line;
1750 spin_lock_irqsave(&card->card_lock, flags);
1751
1752 if (!cy_is_Z(card)) {
1753 /* Stop accepting input */
1754 cyy_writeb(info, CyCAR, channel & 0x03);
1755 cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyRxData);
1756 if (info->port.flags & ASYNC_INITIALIZED) {
1757 /* Waiting for on-board buffers to be empty before
1758 closing the port */
1759 spin_unlock_irqrestore(&card->card_lock, flags);
1760 cy_wait_until_sent(port->tty, info->timeout);
1761 spin_lock_irqsave(&card->card_lock, flags);
1762 }
1763 } else {
1764 #ifdef Z_WAKE
1765 /* Waiting for on-board buffers to be empty before closing
1766 the port */
1767 struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl;
1768 int retval;
1769
1770 if (readl(&ch_ctrl->flow_status) != C_FS_TXIDLE) {
1771 retval = cyz_issue_cmd(card, channel, C_CM_IOCTLW, 0L);
1772 if (retval != 0) {
1773 printk(KERN_DEBUG "cyc:cy_close retval on "
1774 "ttyC%d was %x\n", info->line, retval);
1775 }
1776 spin_unlock_irqrestore(&card->card_lock, flags);
1777 wait_for_completion_interruptible(&info->shutdown_wait);
1778 spin_lock_irqsave(&card->card_lock, flags);
1779 }
1780 #endif
1781 }
1782 spin_unlock_irqrestore(&card->card_lock, flags);
1783 cy_shutdown(info, port->tty);
1784 }
1785
1786 /*
1787 * This routine is called when a particular tty device is closed.
1788 */
1789 static void cy_close(struct tty_struct *tty, struct file *filp)
1790 {
1791 struct cyclades_port *info = tty->driver_data;
1792 if (!info || serial_paranoia_check(info, tty->name, "cy_close"))
1793 return;
1794 tty_port_close(&info->port, tty, filp);
1795 } /* cy_close */
1796
1797 /* This routine gets called when tty_write has put something into
1798 * the write_queue. The characters may come from user space or
1799 * kernel space.
1800 *
1801 * This routine will return the number of characters actually
1802 * accepted for writing.
1803 *
1804 * If the port is not already transmitting stuff, start it off by
1805 * enabling interrupts. The interrupt service routine will then
1806 * ensure that the characters are sent.
1807 * If the port is already active, there is no need to kick it.
1808 *
1809 */
1810 static int cy_write(struct tty_struct *tty, const unsigned char *buf, int count)
1811 {
1812 struct cyclades_port *info = tty->driver_data;
1813 unsigned long flags;
1814 int c, ret = 0;
1815
1816 #ifdef CY_DEBUG_IO
1817 printk(KERN_DEBUG "cyc:cy_write ttyC%d\n", info->line);
1818 #endif
1819
1820 if (serial_paranoia_check(info, tty->name, "cy_write"))
1821 return 0;
1822
1823 if (!info->port.xmit_buf)
1824 return 0;
1825
1826 spin_lock_irqsave(&info->card->card_lock, flags);
1827 while (1) {
1828 c = min(count, (int)(SERIAL_XMIT_SIZE - info->xmit_cnt - 1));
1829 c = min(c, (int)(SERIAL_XMIT_SIZE - info->xmit_head));
1830
1831 if (c <= 0)
1832 break;
1833
1834 memcpy(info->port.xmit_buf + info->xmit_head, buf, c);
1835 info->xmit_head = (info->xmit_head + c) &
1836 (SERIAL_XMIT_SIZE - 1);
1837 info->xmit_cnt += c;
1838 buf += c;
1839 count -= c;
1840 ret += c;
1841 }
1842 spin_unlock_irqrestore(&info->card->card_lock, flags);
1843
1844 info->idle_stats.xmit_bytes += ret;
1845 info->idle_stats.xmit_idle = jiffies;
1846
1847 if (info->xmit_cnt && !tty->stopped && !tty->hw_stopped)
1848 start_xmit(info);
1849
1850 return ret;
1851 } /* cy_write */
1852
1853 /*
1854 * This routine is called by the kernel to write a single
1855 * character to the tty device. If the kernel uses this routine,
1856 * it must call the flush_chars() routine (if defined) when it is
1857 * done stuffing characters into the driver. If there is no room
1858 * in the queue, the character is ignored.
1859 */
1860 static int cy_put_char(struct tty_struct *tty, unsigned char ch)
1861 {
1862 struct cyclades_port *info = tty->driver_data;
1863 unsigned long flags;
1864
1865 #ifdef CY_DEBUG_IO
1866 printk(KERN_DEBUG "cyc:cy_put_char ttyC%d\n", info->line);
1867 #endif
1868
1869 if (serial_paranoia_check(info, tty->name, "cy_put_char"))
1870 return 0;
1871
1872 if (!info->port.xmit_buf)
1873 return 0;
1874
1875 spin_lock_irqsave(&info->card->card_lock, flags);
1876 if (info->xmit_cnt >= (int)(SERIAL_XMIT_SIZE - 1)) {
1877 spin_unlock_irqrestore(&info->card->card_lock, flags);
1878 return 0;
1879 }
1880
1881 info->port.xmit_buf[info->xmit_head++] = ch;
1882 info->xmit_head &= SERIAL_XMIT_SIZE - 1;
1883 info->xmit_cnt++;
1884 info->idle_stats.xmit_bytes++;
1885 info->idle_stats.xmit_idle = jiffies;
1886 spin_unlock_irqrestore(&info->card->card_lock, flags);
1887 return 1;
1888 } /* cy_put_char */
1889
1890 /*
1891 * This routine is called by the kernel after it has written a
1892 * series of characters to the tty device using put_char().
1893 */
1894 static void cy_flush_chars(struct tty_struct *tty)
1895 {
1896 struct cyclades_port *info = tty->driver_data;
1897
1898 #ifdef CY_DEBUG_IO
1899 printk(KERN_DEBUG "cyc:cy_flush_chars ttyC%d\n", info->line);
1900 #endif
1901
1902 if (serial_paranoia_check(info, tty->name, "cy_flush_chars"))
1903 return;
1904
1905 if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
1906 !info->port.xmit_buf)
1907 return;
1908
1909 start_xmit(info);
1910 } /* cy_flush_chars */
1911
1912 /*
1913 * This routine returns the numbers of characters the tty driver
1914 * will accept for queuing to be written. This number is subject
1915 * to change as output buffers get emptied, or if the output flow
1916 * control is activated.
1917 */
1918 static int cy_write_room(struct tty_struct *tty)
1919 {
1920 struct cyclades_port *info = tty->driver_data;
1921 int ret;
1922
1923 #ifdef CY_DEBUG_IO
1924 printk(KERN_DEBUG "cyc:cy_write_room ttyC%d\n", info->line);
1925 #endif
1926
1927 if (serial_paranoia_check(info, tty->name, "cy_write_room"))
1928 return 0;
1929 ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
1930 if (ret < 0)
1931 ret = 0;
1932 return ret;
1933 } /* cy_write_room */
1934
1935 static int cy_chars_in_buffer(struct tty_struct *tty)
1936 {
1937 struct cyclades_port *info = tty->driver_data;
1938
1939 if (serial_paranoia_check(info, tty->name, "cy_chars_in_buffer"))
1940 return 0;
1941
1942 #ifdef Z_EXT_CHARS_IN_BUFFER
1943 if (!cy_is_Z(info->card)) {
1944 #endif /* Z_EXT_CHARS_IN_BUFFER */
1945 #ifdef CY_DEBUG_IO
1946 printk(KERN_DEBUG "cyc:cy_chars_in_buffer ttyC%d %d\n",
1947 info->line, info->xmit_cnt);
1948 #endif
1949 return info->xmit_cnt;
1950 #ifdef Z_EXT_CHARS_IN_BUFFER
1951 } else {
1952 struct BUF_CTRL __iomem *buf_ctrl = info->u.cyz.buf_ctrl;
1953 int char_count;
1954 __u32 tx_put, tx_get, tx_bufsize;
1955
1956 tx_get = readl(&buf_ctrl->tx_get);
1957 tx_put = readl(&buf_ctrl->tx_put);
1958 tx_bufsize = readl(&buf_ctrl->tx_bufsize);
1959 if (tx_put >= tx_get)
1960 char_count = tx_put - tx_get;
1961 else
1962 char_count = tx_put - tx_get + tx_bufsize;
1963 #ifdef CY_DEBUG_IO
1964 printk(KERN_DEBUG "cyc:cy_chars_in_buffer ttyC%d %d\n",
1965 info->line, info->xmit_cnt + char_count);
1966 #endif
1967 return info->xmit_cnt + char_count;
1968 }
1969 #endif /* Z_EXT_CHARS_IN_BUFFER */
1970 } /* cy_chars_in_buffer */
1971
1972 /*
1973 * ------------------------------------------------------------
1974 * cy_ioctl() and friends
1975 * ------------------------------------------------------------
1976 */
1977
1978 static void cyy_baud_calc(struct cyclades_port *info, __u32 baud)
1979 {
1980 int co, co_val, bpr;
1981 __u32 cy_clock = ((info->chip_rev >= CD1400_REV_J) ? 60000000 :
1982 25000000);
1983
1984 if (baud == 0) {
1985 info->tbpr = info->tco = info->rbpr = info->rco = 0;
1986 return;
1987 }
1988
1989 /* determine which prescaler to use */
1990 for (co = 4, co_val = 2048; co; co--, co_val >>= 2) {
1991 if (cy_clock / co_val / baud > 63)
1992 break;
1993 }
1994
1995 bpr = (cy_clock / co_val * 2 / baud + 1) / 2;
1996 if (bpr > 255)
1997 bpr = 255;
1998
1999 info->tbpr = info->rbpr = bpr;
2000 info->tco = info->rco = co;
2001 }
2002
2003 /*
2004 * This routine finds or computes the various line characteristics.
2005 * It used to be called config_setup
2006 */
2007 static void cy_set_line_char(struct cyclades_port *info, struct tty_struct *tty)
2008 {
2009 struct cyclades_card *card;
2010 unsigned long flags;
2011 int channel;
2012 unsigned cflag, iflag;
2013 int baud, baud_rate = 0;
2014 int i;
2015
2016 if (!tty->termios) /* XXX can this happen at all? */
2017 return;
2018
2019 if (info->line == -1)
2020 return;
2021
2022 cflag = tty->termios->c_cflag;
2023 iflag = tty->termios->c_iflag;
2024
2025 /*
2026 * Set up the tty->alt_speed kludge
2027 */
2028 if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
2029 tty->alt_speed = 57600;
2030 if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
2031 tty->alt_speed = 115200;
2032 if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
2033 tty->alt_speed = 230400;
2034 if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
2035 tty->alt_speed = 460800;
2036
2037 card = info->card;
2038 channel = info->line - card->first_line;
2039
2040 if (!cy_is_Z(card)) {
2041 u32 cflags;
2042
2043 /* baud rate */
2044 baud = tty_get_baud_rate(tty);
2045 if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
2046 ASYNC_SPD_CUST) {
2047 if (info->custom_divisor)
2048 baud_rate = info->baud / info->custom_divisor;
2049 else
2050 baud_rate = info->baud;
2051 } else if (baud > CD1400_MAX_SPEED) {
2052 baud = CD1400_MAX_SPEED;
2053 }
2054 /* find the baud index */
2055 for (i = 0; i < 20; i++) {
2056 if (baud == baud_table[i])
2057 break;
2058 }
2059 if (i == 20)
2060 i = 19; /* CD1400_MAX_SPEED */
2061
2062 if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
2063 ASYNC_SPD_CUST) {
2064 cyy_baud_calc(info, baud_rate);
2065 } else {
2066 if (info->chip_rev >= CD1400_REV_J) {
2067 /* It is a CD1400 rev. J or later */
2068 info->tbpr = baud_bpr_60[i]; /* Tx BPR */
2069 info->tco = baud_co_60[i]; /* Tx CO */
2070 info->rbpr = baud_bpr_60[i]; /* Rx BPR */
2071 info->rco = baud_co_60[i]; /* Rx CO */
2072 } else {
2073 info->tbpr = baud_bpr_25[i]; /* Tx BPR */
2074 info->tco = baud_co_25[i]; /* Tx CO */
2075 info->rbpr = baud_bpr_25[i]; /* Rx BPR */
2076 info->rco = baud_co_25[i]; /* Rx CO */
2077 }
2078 }
2079 if (baud_table[i] == 134) {
2080 /* get it right for 134.5 baud */
2081 info->timeout = (info->xmit_fifo_size * HZ * 30 / 269) +
2082 2;
2083 } else if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
2084 ASYNC_SPD_CUST) {
2085 info->timeout = (info->xmit_fifo_size * HZ * 15 /
2086 baud_rate) + 2;
2087 } else if (baud_table[i]) {
2088 info->timeout = (info->xmit_fifo_size * HZ * 15 /
2089 baud_table[i]) + 2;
2090 /* this needs to be propagated into the card info */
2091 } else {
2092 info->timeout = 0;
2093 }
2094 /* By tradition (is it a standard?) a baud rate of zero
2095 implies the line should be/has been closed. A bit
2096 later in this routine such a test is performed. */
2097
2098 /* byte size and parity */
2099 info->cor5 = 0;
2100 info->cor4 = 0;
2101 /* receive threshold */
2102 info->cor3 = (info->default_threshold ?
2103 info->default_threshold : baud_cor3[i]);
2104 info->cor2 = CyETC;
2105 switch (cflag & CSIZE) {
2106 case CS5:
2107 info->cor1 = Cy_5_BITS;
2108 break;
2109 case CS6:
2110 info->cor1 = Cy_6_BITS;
2111 break;
2112 case CS7:
2113 info->cor1 = Cy_7_BITS;
2114 break;
2115 case CS8:
2116 info->cor1 = Cy_8_BITS;
2117 break;
2118 }
2119 if (cflag & CSTOPB)
2120 info->cor1 |= Cy_2_STOP;
2121
2122 if (cflag & PARENB) {
2123 if (cflag & PARODD)
2124 info->cor1 |= CyPARITY_O;
2125 else
2126 info->cor1 |= CyPARITY_E;
2127 } else
2128 info->cor1 |= CyPARITY_NONE;
2129
2130 /* CTS flow control flag */
2131 if (cflag & CRTSCTS) {
2132 info->port.flags |= ASYNC_CTS_FLOW;
2133 info->cor2 |= CyCtsAE;
2134 } else {
2135 info->port.flags &= ~ASYNC_CTS_FLOW;
2136 info->cor2 &= ~CyCtsAE;
2137 }
2138 if (cflag & CLOCAL)
2139 info->port.flags &= ~ASYNC_CHECK_CD;
2140 else
2141 info->port.flags |= ASYNC_CHECK_CD;
2142
2143 /***********************************************
2144 The hardware option, CyRtsAO, presents RTS when
2145 the chip has characters to send. Since most modems
2146 use RTS as reverse (inbound) flow control, this
2147 option is not used. If inbound flow control is
2148 necessary, DTR can be programmed to provide the
2149 appropriate signals for use with a non-standard
2150 cable. Contact Marcio Saito for details.
2151 ***********************************************/
2152
2153 channel &= 0x03;
2154
2155 spin_lock_irqsave(&card->card_lock, flags);
2156 cyy_writeb(info, CyCAR, channel);
2157
2158 /* tx and rx baud rate */
2159
2160 cyy_writeb(info, CyTCOR, info->tco);
2161 cyy_writeb(info, CyTBPR, info->tbpr);
2162 cyy_writeb(info, CyRCOR, info->rco);
2163 cyy_writeb(info, CyRBPR, info->rbpr);
2164
2165 /* set line characteristics according configuration */
2166
2167 cyy_writeb(info, CySCHR1, START_CHAR(tty));
2168 cyy_writeb(info, CySCHR2, STOP_CHAR(tty));
2169 cyy_writeb(info, CyCOR1, info->cor1);
2170 cyy_writeb(info, CyCOR2, info->cor2);
2171 cyy_writeb(info, CyCOR3, info->cor3);
2172 cyy_writeb(info, CyCOR4, info->cor4);
2173 cyy_writeb(info, CyCOR5, info->cor5);
2174
2175 cyy_issue_cmd(info, CyCOR_CHANGE | CyCOR1ch | CyCOR2ch |
2176 CyCOR3ch);
2177
2178 /* !!! Is this needed? */
2179 cyy_writeb(info, CyCAR, channel);
2180 cyy_writeb(info, CyRTPR,
2181 (info->default_timeout ? info->default_timeout : 0x02));
2182 /* 10ms rx timeout */
2183
2184 cflags = CyCTS;
2185 if (!C_CLOCAL(tty))
2186 cflags |= CyDSR | CyRI | CyDCD;
2187 /* without modem intr */
2188 cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyMdmCh);
2189 /* act on 1->0 modem transitions */
2190 if ((cflag & CRTSCTS) && info->rflow)
2191 cyy_writeb(info, CyMCOR1, cflags | rflow_thr[i]);
2192 else
2193 cyy_writeb(info, CyMCOR1, cflags);
2194 /* act on 0->1 modem transitions */
2195 cyy_writeb(info, CyMCOR2, cflags);
2196
2197 if (i == 0) /* baud rate is zero, turn off line */
2198 cyy_change_rts_dtr(info, 0, TIOCM_DTR);
2199 else
2200 cyy_change_rts_dtr(info, TIOCM_DTR, 0);
2201
2202 clear_bit(TTY_IO_ERROR, &tty->flags);
2203 spin_unlock_irqrestore(&card->card_lock, flags);
2204
2205 } else {
2206 struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl;
2207 __u32 sw_flow;
2208 int retval;
2209
2210 if (!cyz_is_loaded(card))
2211 return;
2212
2213 /* baud rate */
2214 baud = tty_get_baud_rate(tty);
2215 if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
2216 ASYNC_SPD_CUST) {
2217 if (info->custom_divisor)
2218 baud_rate = info->baud / info->custom_divisor;
2219 else
2220 baud_rate = info->baud;
2221 } else if (baud > CYZ_MAX_SPEED) {
2222 baud = CYZ_MAX_SPEED;
2223 }
2224 cy_writel(&ch_ctrl->comm_baud, baud);
2225
2226 if (baud == 134) {
2227 /* get it right for 134.5 baud */
2228 info->timeout = (info->xmit_fifo_size * HZ * 30 / 269) +
2229 2;
2230 } else if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) ==
2231 ASYNC_SPD_CUST) {
2232 info->timeout = (info->xmit_fifo_size * HZ * 15 /
2233 baud_rate) + 2;
2234 } else if (baud) {
2235 info->timeout = (info->xmit_fifo_size * HZ * 15 /
2236 baud) + 2;
2237 /* this needs to be propagated into the card info */
2238 } else {
2239 info->timeout = 0;
2240 }
2241
2242 /* byte size and parity */
2243 switch (cflag & CSIZE) {
2244 case CS5:
2245 cy_writel(&ch_ctrl->comm_data_l, C_DL_CS5);
2246 break;
2247 case CS6:
2248 cy_writel(&ch_ctrl->comm_data_l, C_DL_CS6);
2249 break;
2250 case CS7:
2251 cy_writel(&ch_ctrl->comm_data_l, C_DL_CS7);
2252 break;
2253 case CS8:
2254 cy_writel(&ch_ctrl->comm_data_l, C_DL_CS8);
2255 break;
2256 }
2257 if (cflag & CSTOPB) {
2258 cy_writel(&ch_ctrl->comm_data_l,
2259 readl(&ch_ctrl->comm_data_l) | C_DL_2STOP);
2260 } else {
2261 cy_writel(&ch_ctrl->comm_data_l,
2262 readl(&ch_ctrl->comm_data_l) | C_DL_1STOP);
2263 }
2264 if (cflag & PARENB) {
2265 if (cflag & PARODD)
2266 cy_writel(&ch_ctrl->comm_parity, C_PR_ODD);
2267 else
2268 cy_writel(&ch_ctrl->comm_parity, C_PR_EVEN);
2269 } else
2270 cy_writel(&ch_ctrl->comm_parity, C_PR_NONE);
2271
2272 /* CTS flow control flag */
2273 if (cflag & CRTSCTS) {
2274 cy_writel(&ch_ctrl->hw_flow,
2275 readl(&ch_ctrl->hw_flow) | C_RS_CTS | C_RS_RTS);
2276 } else {
2277 cy_writel(&ch_ctrl->hw_flow, readl(&ch_ctrl->hw_flow) &
2278 ~(C_RS_CTS | C_RS_RTS));
2279 }
2280 /* As the HW flow control is done in firmware, the driver
2281 doesn't need to care about it */
2282 info->port.flags &= ~ASYNC_CTS_FLOW;
2283
2284 /* XON/XOFF/XANY flow control flags */
2285 sw_flow = 0;
2286 if (iflag & IXON) {
2287 sw_flow |= C_FL_OXX;
2288 if (iflag & IXANY)
2289 sw_flow |= C_FL_OIXANY;
2290 }
2291 cy_writel(&ch_ctrl->sw_flow, sw_flow);
2292
2293 retval = cyz_issue_cmd(card, channel, C_CM_IOCTL, 0L);
2294 if (retval != 0) {
2295 printk(KERN_ERR "cyc:set_line_char retval on ttyC%d "
2296 "was %x\n", info->line, retval);
2297 }
2298
2299 /* CD sensitivity */
2300 if (cflag & CLOCAL)
2301 info->port.flags &= ~ASYNC_CHECK_CD;
2302 else
2303 info->port.flags |= ASYNC_CHECK_CD;
2304
2305 if (baud == 0) { /* baud rate is zero, turn off line */
2306 cy_writel(&ch_ctrl->rs_control,
2307 readl(&ch_ctrl->rs_control) & ~C_RS_DTR);
2308 #ifdef CY_DEBUG_DTR
2309 printk(KERN_DEBUG "cyc:set_line_char dropping Z DTR\n");
2310 #endif
2311 } else {
2312 cy_writel(&ch_ctrl->rs_control,
2313 readl(&ch_ctrl->rs_control) | C_RS_DTR);
2314 #ifdef CY_DEBUG_DTR
2315 printk(KERN_DEBUG "cyc:set_line_char raising Z DTR\n");
2316 #endif
2317 }
2318
2319 retval = cyz_issue_cmd(card, channel, C_CM_IOCTLM, 0L);
2320 if (retval != 0) {
2321 printk(KERN_ERR "cyc:set_line_char(2) retval on ttyC%d "
2322 "was %x\n", info->line, retval);
2323 }
2324
2325 clear_bit(TTY_IO_ERROR, &tty->flags);
2326 }
2327 } /* set_line_char */
2328
2329 static int cy_get_serial_info(struct cyclades_port *info,
2330 struct serial_struct __user *retinfo)
2331 {
2332 struct cyclades_card *cinfo = info->card;
2333 struct serial_struct tmp = {
2334 .type = info->type,
2335 .line = info->line,
2336 .port = (info->card - cy_card) * 0x100 + info->line -
2337 cinfo->first_line,
2338 .irq = cinfo->irq,
2339 .flags = info->port.flags,
2340 .close_delay = info->port.close_delay,
2341 .closing_wait = info->port.closing_wait,
2342 .baud_base = info->baud,
2343 .custom_divisor = info->custom_divisor,
2344 .hub6 = 0, /*!!! */
2345 };
2346 return copy_to_user(retinfo, &tmp, sizeof(*retinfo)) ? -EFAULT : 0;
2347 }
2348
2349 static int
2350 cy_set_serial_info(struct cyclades_port *info, struct tty_struct *tty,
2351 struct serial_struct __user *new_info)
2352 {
2353 struct serial_struct new_serial;
2354 int ret;
2355
2356 if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
2357 return -EFAULT;
2358
2359 mutex_lock(&info->port.mutex);
2360 if (!capable(CAP_SYS_ADMIN)) {
2361 if (new_serial.close_delay != info->port.close_delay ||
2362 new_serial.baud_base != info->baud ||
2363 (new_serial.flags & ASYNC_FLAGS &
2364 ~ASYNC_USR_MASK) !=
2365 (info->port.flags & ASYNC_FLAGS & ~ASYNC_USR_MASK))
2366 {
2367 mutex_unlock(&info->port.mutex);
2368 return -EPERM;
2369 }
2370 info->port.flags = (info->port.flags & ~ASYNC_USR_MASK) |
2371 (new_serial.flags & ASYNC_USR_MASK);
2372 info->baud = new_serial.baud_base;
2373 info->custom_divisor = new_serial.custom_divisor;
2374 goto check_and_exit;
2375 }
2376
2377 /*
2378 * OK, past this point, all the error checking has been done.
2379 * At this point, we start making changes.....
2380 */
2381
2382 info->baud = new_serial.baud_base;
2383 info->custom_divisor = new_serial.custom_divisor;
2384 info->port.flags = (info->port.flags & ~ASYNC_FLAGS) |
2385 (new_serial.flags & ASYNC_FLAGS);
2386 info->port.close_delay = new_serial.close_delay * HZ / 100;
2387 info->port.closing_wait = new_serial.closing_wait * HZ / 100;
2388
2389 check_and_exit:
2390 if (info->port.flags & ASYNC_INITIALIZED) {
2391 cy_set_line_char(info, tty);
2392 ret = 0;
2393 } else {
2394 ret = cy_startup(info, tty);
2395 }
2396 mutex_unlock(&info->port.mutex);
2397 return ret;
2398 } /* set_serial_info */
2399
2400 /*
2401 * get_lsr_info - get line status register info
2402 *
2403 * Purpose: Let user call ioctl() to get info when the UART physically
2404 * is emptied. On bus types like RS485, the transmitter must
2405 * release the bus after transmitting. This must be done when
2406 * the transmit shift register is empty, not be done when the
2407 * transmit holding register is empty. This functionality
2408 * allows an RS485 driver to be written in user space.
2409 */
2410 static int get_lsr_info(struct cyclades_port *info, unsigned int __user *value)
2411 {
2412 struct cyclades_card *card = info->card;
2413 unsigned int result;
2414 unsigned long flags;
2415 u8 status;
2416
2417 if (!cy_is_Z(card)) {
2418 spin_lock_irqsave(&card->card_lock, flags);
2419 status = cyy_readb(info, CySRER) & (CyTxRdy | CyTxMpty);
2420 spin_unlock_irqrestore(&card->card_lock, flags);
2421 result = (status ? 0 : TIOCSER_TEMT);
2422 } else {
2423 /* Not supported yet */
2424 return -EINVAL;
2425 }
2426 return put_user(result, (unsigned long __user *)value);
2427 }
2428
2429 static int cy_tiocmget(struct tty_struct *tty)
2430 {
2431 struct cyclades_port *info = tty->driver_data;
2432 struct cyclades_card *card;
2433 int result;
2434
2435 if (serial_paranoia_check(info, tty->name, __func__))
2436 return -ENODEV;
2437
2438 card = info->card;
2439
2440 if (!cy_is_Z(card)) {
2441 unsigned long flags;
2442 int channel = info->line - card->first_line;
2443 u8 status;
2444
2445 spin_lock_irqsave(&card->card_lock, flags);
2446 cyy_writeb(info, CyCAR, channel & 0x03);
2447 status = cyy_readb(info, CyMSVR1);
2448 status |= cyy_readb(info, CyMSVR2);
2449 spin_unlock_irqrestore(&card->card_lock, flags);
2450
2451 if (info->rtsdtr_inv) {
2452 result = ((status & CyRTS) ? TIOCM_DTR : 0) |
2453 ((status & CyDTR) ? TIOCM_RTS : 0);
2454 } else {
2455 result = ((status & CyRTS) ? TIOCM_RTS : 0) |
2456 ((status & CyDTR) ? TIOCM_DTR : 0);
2457 }
2458 result |= ((status & CyDCD) ? TIOCM_CAR : 0) |
2459 ((status & CyRI) ? TIOCM_RNG : 0) |
2460 ((status & CyDSR) ? TIOCM_DSR : 0) |
2461 ((status & CyCTS) ? TIOCM_CTS : 0);
2462 } else {
2463 u32 lstatus;
2464
2465 if (!cyz_is_loaded(card)) {
2466 result = -ENODEV;
2467 goto end;
2468 }
2469
2470 lstatus = readl(&info->u.cyz.ch_ctrl->rs_status);
2471 result = ((lstatus & C_RS_RTS) ? TIOCM_RTS : 0) |
2472 ((lstatus & C_RS_DTR) ? TIOCM_DTR : 0) |
2473 ((lstatus & C_RS_DCD) ? TIOCM_CAR : 0) |
2474 ((lstatus & C_RS_RI) ? TIOCM_RNG : 0) |
2475 ((lstatus & C_RS_DSR) ? TIOCM_DSR : 0) |
2476 ((lstatus & C_RS_CTS) ? TIOCM_CTS : 0);
2477 }
2478 end:
2479 return result;
2480 } /* cy_tiomget */
2481
2482 static int
2483 cy_tiocmset(struct tty_struct *tty,
2484 unsigned int set, unsigned int clear)
2485 {
2486 struct cyclades_port *info = tty->driver_data;
2487 struct cyclades_card *card;
2488 unsigned long flags;
2489
2490 if (serial_paranoia_check(info, tty->name, __func__))
2491 return -ENODEV;
2492
2493 card = info->card;
2494 if (!cy_is_Z(card)) {
2495 spin_lock_irqsave(&card->card_lock, flags);
2496 cyy_change_rts_dtr(info, set, clear);
2497 spin_unlock_irqrestore(&card->card_lock, flags);
2498 } else {
2499 struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl;
2500 int retval, channel = info->line - card->first_line;
2501 u32 rs;
2502
2503 if (!cyz_is_loaded(card))
2504 return -ENODEV;
2505
2506 spin_lock_irqsave(&card->card_lock, flags);
2507 rs = readl(&ch_ctrl->rs_control);
2508 if (set & TIOCM_RTS)
2509 rs |= C_RS_RTS;
2510 if (clear & TIOCM_RTS)
2511 rs &= ~C_RS_RTS;
2512 if (set & TIOCM_DTR) {
2513 rs |= C_RS_DTR;
2514 #ifdef CY_DEBUG_DTR
2515 printk(KERN_DEBUG "cyc:set_modem_info raising Z DTR\n");
2516 #endif
2517 }
2518 if (clear & TIOCM_DTR) {
2519 rs &= ~C_RS_DTR;
2520 #ifdef CY_DEBUG_DTR
2521 printk(KERN_DEBUG "cyc:set_modem_info clearing "
2522 "Z DTR\n");
2523 #endif
2524 }
2525 cy_writel(&ch_ctrl->rs_control, rs);
2526 retval = cyz_issue_cmd(card, channel, C_CM_IOCTLM, 0L);
2527 spin_unlock_irqrestore(&card->card_lock, flags);
2528 if (retval != 0) {
2529 printk(KERN_ERR "cyc:set_modem_info retval on ttyC%d "
2530 "was %x\n", info->line, retval);
2531 }
2532 }
2533 return 0;
2534 }
2535
2536 /*
2537 * cy_break() --- routine which turns the break handling on or off
2538 */
2539 static int cy_break(struct tty_struct *tty, int break_state)
2540 {
2541 struct cyclades_port *info = tty->driver_data;
2542 struct cyclades_card *card;
2543 unsigned long flags;
2544 int retval = 0;
2545
2546 if (serial_paranoia_check(info, tty->name, "cy_break"))
2547 return -EINVAL;
2548
2549 card = info->card;
2550
2551 spin_lock_irqsave(&card->card_lock, flags);
2552 if (!cy_is_Z(card)) {
2553 /* Let the transmit ISR take care of this (since it
2554 requires stuffing characters into the output stream).
2555 */
2556 if (break_state == -1) {
2557 if (!info->breakon) {
2558 info->breakon = 1;
2559 if (!info->xmit_cnt) {
2560 spin_unlock_irqrestore(&card->card_lock, flags);
2561 start_xmit(info);
2562 spin_lock_irqsave(&card->card_lock, flags);
2563 }
2564 }
2565 } else {
2566 if (!info->breakoff) {
2567 info->breakoff = 1;
2568 if (!info->xmit_cnt) {
2569 spin_unlock_irqrestore(&card->card_lock, flags);
2570 start_xmit(info);
2571 spin_lock_irqsave(&card->card_lock, flags);
2572 }
2573 }
2574 }
2575 } else {
2576 if (break_state == -1) {
2577 retval = cyz_issue_cmd(card,
2578 info->line - card->first_line,
2579 C_CM_SET_BREAK, 0L);
2580 if (retval != 0) {
2581 printk(KERN_ERR "cyc:cy_break (set) retval on "
2582 "ttyC%d was %x\n", info->line, retval);
2583 }
2584 } else {
2585 retval = cyz_issue_cmd(card,
2586 info->line - card->first_line,
2587 C_CM_CLR_BREAK, 0L);
2588 if (retval != 0) {
2589 printk(KERN_DEBUG "cyc:cy_break (clr) retval "
2590 "on ttyC%d was %x\n", info->line,
2591 retval);
2592 }
2593 }
2594 }
2595 spin_unlock_irqrestore(&card->card_lock, flags);
2596 return retval;
2597 } /* cy_break */
2598
2599 static int set_threshold(struct cyclades_port *info, unsigned long value)
2600 {
2601 struct cyclades_card *card = info->card;
2602 unsigned long flags;
2603
2604 if (!cy_is_Z(card)) {
2605 info->cor3 &= ~CyREC_FIFO;
2606 info->cor3 |= value & CyREC_FIFO;
2607
2608 spin_lock_irqsave(&card->card_lock, flags);
2609 cyy_writeb(info, CyCOR3, info->cor3);
2610 cyy_issue_cmd(info, CyCOR_CHANGE | CyCOR3ch);
2611 spin_unlock_irqrestore(&card->card_lock, flags);
2612 }
2613 return 0;
2614 } /* set_threshold */
2615
2616 static int get_threshold(struct cyclades_port *info,
2617 unsigned long __user *value)
2618 {
2619 struct cyclades_card *card = info->card;
2620
2621 if (!cy_is_Z(card)) {
2622 u8 tmp = cyy_readb(info, CyCOR3) & CyREC_FIFO;
2623 return put_user(tmp, value);
2624 }
2625 return 0;
2626 } /* get_threshold */
2627
2628 static int set_timeout(struct cyclades_port *info, unsigned long value)
2629 {
2630 struct cyclades_card *card = info->card;
2631 unsigned long flags;
2632
2633 if (!cy_is_Z(card)) {
2634 spin_lock_irqsave(&card->card_lock, flags);
2635 cyy_writeb(info, CyRTPR, value & 0xff);
2636 spin_unlock_irqrestore(&card->card_lock, flags);
2637 }
2638 return 0;
2639 } /* set_timeout */
2640
2641 static int get_timeout(struct cyclades_port *info,
2642 unsigned long __user *value)
2643 {
2644 struct cyclades_card *card = info->card;
2645
2646 if (!cy_is_Z(card)) {
2647 u8 tmp = cyy_readb(info, CyRTPR);
2648 return put_user(tmp, value);
2649 }
2650 return 0;
2651 } /* get_timeout */
2652
2653 static int cy_cflags_changed(struct cyclades_port *info, unsigned long arg,
2654 struct cyclades_icount *cprev)
2655 {
2656 struct cyclades_icount cnow;
2657 unsigned long flags;
2658 int ret;
2659
2660 spin_lock_irqsave(&info->card->card_lock, flags);
2661 cnow = info->icount; /* atomic copy */
2662 spin_unlock_irqrestore(&info->card->card_lock, flags);
2663
2664 ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) ||
2665 ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) ||
2666 ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) ||
2667 ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts));
2668
2669 *cprev = cnow;
2670
2671 return ret;
2672 }
2673
2674 /*
2675 * This routine allows the tty driver to implement device-
2676 * specific ioctl's. If the ioctl number passed in cmd is
2677 * not recognized by the driver, it should return ENOIOCTLCMD.
2678 */
2679 static int
2680 cy_ioctl(struct tty_struct *tty,
2681 unsigned int cmd, unsigned long arg)
2682 {
2683 struct cyclades_port *info = tty->driver_data;
2684 struct cyclades_icount cnow; /* kernel counter temps */
2685 int ret_val = 0;
2686 unsigned long flags;
2687 void __user *argp = (void __user *)arg;
2688
2689 if (serial_paranoia_check(info, tty->name, "cy_ioctl"))
2690 return -ENODEV;
2691
2692 #ifdef CY_DEBUG_OTHER
2693 printk(KERN_DEBUG "cyc:cy_ioctl ttyC%d, cmd = %x arg = %lx\n",
2694 info->line, cmd, arg);
2695 #endif
2696
2697 switch (cmd) {
2698 case CYGETMON:
2699 if (copy_to_user(argp, &info->mon, sizeof(info->mon))) {
2700 ret_val = -EFAULT;
2701 break;
2702 }
2703 memset(&info->mon, 0, sizeof(info->mon));
2704 break;
2705 case CYGETTHRESH:
2706 ret_val = get_threshold(info, argp);
2707 break;
2708 case CYSETTHRESH:
2709 ret_val = set_threshold(info, arg);
2710 break;
2711 case CYGETDEFTHRESH:
2712 ret_val = put_user(info->default_threshold,
2713 (unsigned long __user *)argp);
2714 break;
2715 case CYSETDEFTHRESH:
2716 info->default_threshold = arg & 0x0f;
2717 break;
2718 case CYGETTIMEOUT:
2719 ret_val = get_timeout(info, argp);
2720 break;
2721 case CYSETTIMEOUT:
2722 ret_val = set_timeout(info, arg);
2723 break;
2724 case CYGETDEFTIMEOUT:
2725 ret_val = put_user(info->default_timeout,
2726 (unsigned long __user *)argp);
2727 break;
2728 case CYSETDEFTIMEOUT:
2729 info->default_timeout = arg & 0xff;
2730 break;
2731 case CYSETRFLOW:
2732 info->rflow = (int)arg;
2733 break;
2734 case CYGETRFLOW:
2735 ret_val = info->rflow;
2736 break;
2737 case CYSETRTSDTR_INV:
2738 info->rtsdtr_inv = (int)arg;
2739 break;
2740 case CYGETRTSDTR_INV:
2741 ret_val = info->rtsdtr_inv;
2742 break;
2743 case CYGETCD1400VER:
2744 ret_val = info->chip_rev;
2745 break;
2746 #ifndef CONFIG_CYZ_INTR
2747 case CYZSETPOLLCYCLE:
2748 cyz_polling_cycle = (arg * HZ) / 1000;
2749 break;
2750 case CYZGETPOLLCYCLE:
2751 ret_val = (cyz_polling_cycle * 1000) / HZ;
2752 break;
2753 #endif /* CONFIG_CYZ_INTR */
2754 case CYSETWAIT:
2755 info->port.closing_wait = (unsigned short)arg * HZ / 100;
2756 break;
2757 case CYGETWAIT:
2758 ret_val = info->port.closing_wait / (HZ / 100);
2759 break;
2760 case TIOCGSERIAL:
2761 ret_val = cy_get_serial_info(info, argp);
2762 break;
2763 case TIOCSSERIAL:
2764 ret_val = cy_set_serial_info(info, tty, argp);
2765 break;
2766 case TIOCSERGETLSR: /* Get line status register */
2767 ret_val = get_lsr_info(info, argp);
2768 break;
2769 /*
2770 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
2771 * - mask passed in arg for lines of interest
2772 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
2773 * Caller should use TIOCGICOUNT to see which one it was
2774 */
2775 case TIOCMIWAIT:
2776 spin_lock_irqsave(&info->card->card_lock, flags);
2777 /* note the counters on entry */
2778 cnow = info->icount;
2779 spin_unlock_irqrestore(&info->card->card_lock, flags);
2780 ret_val = wait_event_interruptible(info->port.delta_msr_wait,
2781 cy_cflags_changed(info, arg, &cnow));
2782 break;
2783
2784 /*
2785 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
2786 * Return: write counters to the user passed counter struct
2787 * NB: both 1->0 and 0->1 transitions are counted except for
2788 * RI where only 0->1 is counted.
2789 */
2790 default:
2791 ret_val = -ENOIOCTLCMD;
2792 }
2793
2794 #ifdef CY_DEBUG_OTHER
2795 printk(KERN_DEBUG "cyc:cy_ioctl done\n");
2796 #endif
2797 return ret_val;
2798 } /* cy_ioctl */
2799
2800 static int cy_get_icount(struct tty_struct *tty,
2801 struct serial_icounter_struct *sic)
2802 {
2803 struct cyclades_port *info = tty->driver_data;
2804 struct cyclades_icount cnow; /* Used to snapshot */
2805 unsigned long flags;
2806
2807 spin_lock_irqsave(&info->card->card_lock, flags);
2808 cnow = info->icount;
2809 spin_unlock_irqrestore(&info->card->card_lock, flags);
2810
2811 sic->cts = cnow.cts;
2812 sic->dsr = cnow.dsr;
2813 sic->rng = cnow.rng;
2814 sic->dcd = cnow.dcd;
2815 sic->rx = cnow.rx;
2816 sic->tx = cnow.tx;
2817 sic->frame = cnow.frame;
2818 sic->overrun = cnow.overrun;
2819 sic->parity = cnow.parity;
2820 sic->brk = cnow.brk;
2821 sic->buf_overrun = cnow.buf_overrun;
2822 return 0;
2823 }
2824
2825 /*
2826 * This routine allows the tty driver to be notified when
2827 * device's termios settings have changed. Note that a
2828 * well-designed tty driver should be prepared to accept the case
2829 * where old == NULL, and try to do something rational.
2830 */
2831 static void cy_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
2832 {
2833 struct cyclades_port *info = tty->driver_data;
2834
2835 #ifdef CY_DEBUG_OTHER
2836 printk(KERN_DEBUG "cyc:cy_set_termios ttyC%d\n", info->line);
2837 #endif
2838
2839 cy_set_line_char(info, tty);
2840
2841 if ((old_termios->c_cflag & CRTSCTS) &&
2842 !(tty->termios->c_cflag & CRTSCTS)) {
2843 tty->hw_stopped = 0;
2844 cy_start(tty);
2845 }
2846 #if 0
2847 /*
2848 * No need to wake up processes in open wait, since they
2849 * sample the CLOCAL flag once, and don't recheck it.
2850 * XXX It's not clear whether the current behavior is correct
2851 * or not. Hence, this may change.....
2852 */
2853 if (!(old_termios->c_cflag & CLOCAL) &&
2854 (tty->termios->c_cflag & CLOCAL))
2855 wake_up_interruptible(&info->port.open_wait);
2856 #endif
2857 } /* cy_set_termios */
2858
2859 /* This function is used to send a high-priority XON/XOFF character to
2860 the device.
2861 */
2862 static void cy_send_xchar(struct tty_struct *tty, char ch)
2863 {
2864 struct cyclades_port *info = tty->driver_data;
2865 struct cyclades_card *card;
2866 int channel;
2867
2868 if (serial_paranoia_check(info, tty->name, "cy_send_xchar"))
2869 return;
2870
2871 info->x_char = ch;
2872
2873 if (ch)
2874 cy_start(tty);
2875
2876 card = info->card;
2877 channel = info->line - card->first_line;
2878
2879 if (cy_is_Z(card)) {
2880 if (ch == STOP_CHAR(tty))
2881 cyz_issue_cmd(card, channel, C_CM_SENDXOFF, 0L);
2882 else if (ch == START_CHAR(tty))
2883 cyz_issue_cmd(card, channel, C_CM_SENDXON, 0L);
2884 }
2885 }
2886
2887 /* This routine is called by the upper-layer tty layer to signal
2888 that incoming characters should be throttled because the input
2889 buffers are close to full.
2890 */
2891 static void cy_throttle(struct tty_struct *tty)
2892 {
2893 struct cyclades_port *info = tty->driver_data;
2894 struct cyclades_card *card;
2895 unsigned long flags;
2896
2897 #ifdef CY_DEBUG_THROTTLE
2898 char buf[64];
2899
2900 printk(KERN_DEBUG "cyc:throttle %s: %ld...ttyC%d\n", tty_name(tty, buf),
2901 tty->ldisc.chars_in_buffer(tty), info->line);
2902 #endif
2903
2904 if (serial_paranoia_check(info, tty->name, "cy_throttle"))
2905 return;
2906
2907 card = info->card;
2908
2909 if (I_IXOFF(tty)) {
2910 if (!cy_is_Z(card))
2911 cy_send_xchar(tty, STOP_CHAR(tty));
2912 else
2913 info->throttle = 1;
2914 }
2915
2916 if (tty->termios->c_cflag & CRTSCTS) {
2917 if (!cy_is_Z(card)) {
2918 spin_lock_irqsave(&card->card_lock, flags);
2919 cyy_change_rts_dtr(info, 0, TIOCM_RTS);
2920 spin_unlock_irqrestore(&card->card_lock, flags);
2921 } else {
2922 info->throttle = 1;
2923 }
2924 }
2925 } /* cy_throttle */
2926
2927 /*
2928 * This routine notifies the tty driver that it should signal
2929 * that characters can now be sent to the tty without fear of
2930 * overrunning the input buffers of the line disciplines.
2931 */
2932 static void cy_unthrottle(struct tty_struct *tty)
2933 {
2934 struct cyclades_port *info = tty->driver_data;
2935 struct cyclades_card *card;
2936 unsigned long flags;
2937
2938 #ifdef CY_DEBUG_THROTTLE
2939 char buf[64];
2940
2941 printk(KERN_DEBUG "cyc:unthrottle %s: %ld...ttyC%d\n",
2942 tty_name(tty, buf), tty_chars_in_buffer(tty), info->line);
2943 #endif
2944
2945 if (serial_paranoia_check(info, tty->name, "cy_unthrottle"))
2946 return;
2947
2948 if (I_IXOFF(tty)) {
2949 if (info->x_char)
2950 info->x_char = 0;
2951 else
2952 cy_send_xchar(tty, START_CHAR(tty));
2953 }
2954
2955 if (tty->termios->c_cflag & CRTSCTS) {
2956 card = info->card;
2957 if (!cy_is_Z(card)) {
2958 spin_lock_irqsave(&card->card_lock, flags);
2959 cyy_change_rts_dtr(info, TIOCM_RTS, 0);
2960 spin_unlock_irqrestore(&card->card_lock, flags);
2961 } else {
2962 info->throttle = 0;
2963 }
2964 }
2965 } /* cy_unthrottle */
2966
2967 /* cy_start and cy_stop provide software output flow control as a
2968 function of XON/XOFF, software CTS, and other such stuff.
2969 */
2970 static void cy_stop(struct tty_struct *tty)
2971 {
2972 struct cyclades_card *cinfo;
2973 struct cyclades_port *info = tty->driver_data;
2974 int channel;
2975 unsigned long flags;
2976
2977 #ifdef CY_DEBUG_OTHER
2978 printk(KERN_DEBUG "cyc:cy_stop ttyC%d\n", info->line);
2979 #endif
2980
2981 if (serial_paranoia_check(info, tty->name, "cy_stop"))
2982 return;
2983
2984 cinfo = info->card;
2985 channel = info->line - cinfo->first_line;
2986 if (!cy_is_Z(cinfo)) {
2987 spin_lock_irqsave(&cinfo->card_lock, flags);
2988 cyy_writeb(info, CyCAR, channel & 0x03);
2989 cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyTxRdy);
2990 spin_unlock_irqrestore(&cinfo->card_lock, flags);
2991 }
2992 } /* cy_stop */
2993
2994 static void cy_start(struct tty_struct *tty)
2995 {
2996 struct cyclades_card *cinfo;
2997 struct cyclades_port *info = tty->driver_data;
2998 int channel;
2999 unsigned long flags;
3000
3001 #ifdef CY_DEBUG_OTHER
3002 printk(KERN_DEBUG "cyc:cy_start ttyC%d\n", info->line);
3003 #endif
3004
3005 if (serial_paranoia_check(info, tty->name, "cy_start"))
3006 return;
3007
3008 cinfo = info->card;
3009 channel = info->line - cinfo->first_line;
3010 if (!cy_is_Z(cinfo)) {
3011 spin_lock_irqsave(&cinfo->card_lock, flags);
3012 cyy_writeb(info, CyCAR, channel & 0x03);
3013 cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyTxRdy);
3014 spin_unlock_irqrestore(&cinfo->card_lock, flags);
3015 }
3016 } /* cy_start */
3017
3018 /*
3019 * cy_hangup() --- called by tty_hangup() when a hangup is signaled.
3020 */
3021 static void cy_hangup(struct tty_struct *tty)
3022 {
3023 struct cyclades_port *info = tty->driver_data;
3024
3025 #ifdef CY_DEBUG_OTHER
3026 printk(KERN_DEBUG "cyc:cy_hangup ttyC%d\n", info->line);
3027 #endif
3028
3029 if (serial_paranoia_check(info, tty->name, "cy_hangup"))
3030 return;
3031
3032 cy_flush_buffer(tty);
3033 cy_shutdown(info, tty);
3034 tty_port_hangup(&info->port);
3035 } /* cy_hangup */
3036
3037 static int cyy_carrier_raised(struct tty_port *port)
3038 {
3039 struct cyclades_port *info = container_of(port, struct cyclades_port,
3040 port);
3041 struct cyclades_card *cinfo = info->card;
3042 unsigned long flags;
3043 int channel = info->line - cinfo->first_line;
3044 u32 cd;
3045
3046 spin_lock_irqsave(&cinfo->card_lock, flags);
3047 cyy_writeb(info, CyCAR, channel & 0x03);
3048 cd = cyy_readb(info, CyMSVR1) & CyDCD;
3049 spin_unlock_irqrestore(&cinfo->card_lock, flags);
3050
3051 return cd;
3052 }
3053
3054 static void cyy_dtr_rts(struct tty_port *port, int raise)
3055 {
3056 struct cyclades_port *info = container_of(port, struct cyclades_port,
3057 port);
3058 struct cyclades_card *cinfo = info->card;
3059 unsigned long flags;
3060
3061 spin_lock_irqsave(&cinfo->card_lock, flags);
3062 cyy_change_rts_dtr(info, raise ? TIOCM_RTS | TIOCM_DTR : 0,
3063 raise ? 0 : TIOCM_RTS | TIOCM_DTR);
3064 spin_unlock_irqrestore(&cinfo->card_lock, flags);
3065 }
3066
3067 static int cyz_carrier_raised(struct tty_port *port)
3068 {
3069 struct cyclades_port *info = container_of(port, struct cyclades_port,
3070 port);
3071
3072 return readl(&info->u.cyz.ch_ctrl->rs_status) & C_RS_DCD;
3073 }
3074
3075 static void cyz_dtr_rts(struct tty_port *port, int raise)
3076 {
3077 struct cyclades_port *info = container_of(port, struct cyclades_port,
3078 port);
3079 struct cyclades_card *cinfo = info->card;
3080 struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl;
3081 int ret, channel = info->line - cinfo->first_line;
3082 u32 rs;
3083
3084 rs = readl(&ch_ctrl->rs_control);
3085 if (raise)
3086 rs |= C_RS_RTS | C_RS_DTR;
3087 else
3088 rs &= ~(C_RS_RTS | C_RS_DTR);
3089 cy_writel(&ch_ctrl->rs_control, rs);
3090 ret = cyz_issue_cmd(cinfo, channel, C_CM_IOCTLM, 0L);
3091 if (ret != 0)
3092 printk(KERN_ERR "%s: retval on ttyC%d was %x\n",
3093 __func__, info->line, ret);
3094 #ifdef CY_DEBUG_DTR
3095 printk(KERN_DEBUG "%s: raising Z DTR\n", __func__);
3096 #endif
3097 }
3098
3099 static const struct tty_port_operations cyy_port_ops = {
3100 .carrier_raised = cyy_carrier_raised,
3101 .dtr_rts = cyy_dtr_rts,
3102 .shutdown = cy_do_close,
3103 };
3104
3105 static const struct tty_port_operations cyz_port_ops = {
3106 .carrier_raised = cyz_carrier_raised,
3107 .dtr_rts = cyz_dtr_rts,
3108 .shutdown = cy_do_close,
3109 };
3110
3111 /*
3112 * ---------------------------------------------------------------------
3113 * cy_init() and friends
3114 *
3115 * cy_init() is called at boot-time to initialize the serial driver.
3116 * ---------------------------------------------------------------------
3117 */
3118
3119 static int __devinit cy_init_card(struct cyclades_card *cinfo)
3120 {
3121 struct cyclades_port *info;
3122 unsigned int channel, port;
3123
3124 spin_lock_init(&cinfo->card_lock);
3125 cinfo->intr_enabled = 0;
3126
3127 cinfo->ports = kcalloc(cinfo->nports, sizeof(*cinfo->ports),
3128 GFP_KERNEL);
3129 if (cinfo->ports == NULL) {
3130 printk(KERN_ERR "Cyclades: cannot allocate ports\n");
3131 return -ENOMEM;
3132 }
3133
3134 for (channel = 0, port = cinfo->first_line; channel < cinfo->nports;
3135 channel++, port++) {
3136 info = &cinfo->ports[channel];
3137 tty_port_init(&info->port);
3138 info->magic = CYCLADES_MAGIC;
3139 info->card = cinfo;
3140 info->line = port;
3141
3142 info->port.closing_wait = CLOSING_WAIT_DELAY;
3143 info->port.close_delay = 5 * HZ / 10;
3144 info->port.flags = STD_COM_FLAGS;
3145 init_completion(&info->shutdown_wait);
3146
3147 if (cy_is_Z(cinfo)) {
3148 struct FIRM_ID *firm_id = cinfo->base_addr + ID_ADDRESS;
3149 struct ZFW_CTRL *zfw_ctrl;
3150
3151 info->port.ops = &cyz_port_ops;
3152 info->type = PORT_STARTECH;
3153
3154 zfw_ctrl = cinfo->base_addr +
3155 (readl(&firm_id->zfwctrl_addr) & 0xfffff);
3156 info->u.cyz.ch_ctrl = &zfw_ctrl->ch_ctrl[channel];
3157 info->u.cyz.buf_ctrl = &zfw_ctrl->buf_ctrl[channel];
3158
3159 if (cinfo->hw_ver == ZO_V1)
3160 info->xmit_fifo_size = CYZ_FIFO_SIZE;
3161 else
3162 info->xmit_fifo_size = 4 * CYZ_FIFO_SIZE;
3163 #ifdef CONFIG_CYZ_INTR
3164 setup_timer(&cyz_rx_full_timer[port],
3165 cyz_rx_restart, (unsigned long)info);
3166 #endif
3167 } else {
3168 unsigned short chip_number;
3169 int index = cinfo->bus_index;
3170
3171 info->port.ops = &cyy_port_ops;
3172 info->type = PORT_CIRRUS;
3173 info->xmit_fifo_size = CyMAX_CHAR_FIFO;
3174 info->cor1 = CyPARITY_NONE | Cy_1_STOP | Cy_8_BITS;
3175 info->cor2 = CyETC;
3176 info->cor3 = 0x08; /* _very_ small rcv threshold */
3177
3178 chip_number = channel / CyPORTS_PER_CHIP;
3179 info->u.cyy.base_addr = cinfo->base_addr +
3180 (cy_chip_offset[chip_number] << index);
3181 info->chip_rev = cyy_readb(info, CyGFRCR);
3182
3183 if (info->chip_rev >= CD1400_REV_J) {
3184 /* It is a CD1400 rev. J or later */
3185 info->tbpr = baud_bpr_60[13]; /* Tx BPR */
3186 info->tco = baud_co_60[13]; /* Tx CO */
3187 info->rbpr = baud_bpr_60[13]; /* Rx BPR */
3188 info->rco = baud_co_60[13]; /* Rx CO */
3189 info->rtsdtr_inv = 1;
3190 } else {
3191 info->tbpr = baud_bpr_25[13]; /* Tx BPR */
3192 info->tco = baud_co_25[13]; /* Tx CO */
3193 info->rbpr = baud_bpr_25[13]; /* Rx BPR */
3194 info->rco = baud_co_25[13]; /* Rx CO */
3195 info->rtsdtr_inv = 0;
3196 }
3197 info->read_status_mask = CyTIMEOUT | CySPECHAR |
3198 CyBREAK | CyPARITY | CyFRAME | CyOVERRUN;
3199 }
3200
3201 }
3202
3203 #ifndef CONFIG_CYZ_INTR
3204 if (cy_is_Z(cinfo) && !timer_pending(&cyz_timerlist)) {
3205 mod_timer(&cyz_timerlist, jiffies + 1);
3206 #ifdef CY_PCI_DEBUG
3207 printk(KERN_DEBUG "Cyclades-Z polling initialized\n");
3208 #endif
3209 }
3210 #endif
3211 return 0;
3212 }
3213
3214 /* initialize chips on Cyclom-Y card -- return number of valid
3215 chips (which is number of ports/4) */
3216 static unsigned short __devinit cyy_init_card(void __iomem *true_base_addr,
3217 int index)
3218 {
3219 unsigned int chip_number;
3220 void __iomem *base_addr;
3221
3222 cy_writeb(true_base_addr + (Cy_HwReset << index), 0);
3223 /* Cy_HwReset is 0x1400 */
3224 cy_writeb(true_base_addr + (Cy_ClrIntr << index), 0);
3225 /* Cy_ClrIntr is 0x1800 */
3226 udelay(500L);
3227
3228 for (chip_number = 0; chip_number < CyMAX_CHIPS_PER_CARD;
3229 chip_number++) {
3230 base_addr =
3231 true_base_addr + (cy_chip_offset[chip_number] << index);
3232 mdelay(1);
3233 if (readb(base_addr + (CyCCR << index)) != 0x00) {
3234 /*************
3235 printk(" chip #%d at %#6lx is never idle (CCR != 0)\n",
3236 chip_number, (unsigned long)base_addr);
3237 *************/
3238 return chip_number;
3239 }
3240
3241 cy_writeb(base_addr + (CyGFRCR << index), 0);
3242 udelay(10L);
3243
3244 /* The Cyclom-16Y does not decode address bit 9 and therefore
3245 cannot distinguish between references to chip 0 and a non-
3246 existent chip 4. If the preceding clearing of the supposed
3247 chip 4 GFRCR register appears at chip 0, there is no chip 4
3248 and this must be a Cyclom-16Y, not a Cyclom-32Ye.
3249 */
3250 if (chip_number == 4 && readb(true_base_addr +
3251 (cy_chip_offset[0] << index) +
3252 (CyGFRCR << index)) == 0) {
3253 return chip_number;
3254 }
3255
3256 cy_writeb(base_addr + (CyCCR << index), CyCHIP_RESET);
3257 mdelay(1);
3258
3259 if (readb(base_addr + (CyGFRCR << index)) == 0x00) {
3260 /*
3261 printk(" chip #%d at %#6lx is not responding ",
3262 chip_number, (unsigned long)base_addr);
3263 printk("(GFRCR stayed 0)\n",
3264 */
3265 return chip_number;
3266 }
3267 if ((0xf0 & (readb(base_addr + (CyGFRCR << index)))) !=
3268 0x40) {
3269 /*
3270 printk(" chip #%d at %#6lx is not valid (GFRCR == "
3271 "%#2x)\n",
3272 chip_number, (unsigned long)base_addr,
3273 base_addr[CyGFRCR<<index]);
3274 */
3275 return chip_number;
3276 }
3277 cy_writeb(base_addr + (CyGCR << index), CyCH0_SERIAL);
3278 if (readb(base_addr + (CyGFRCR << index)) >= CD1400_REV_J) {
3279 /* It is a CD1400 rev. J or later */
3280 /* Impossible to reach 5ms with this chip.
3281 Changed to 2ms instead (f = 500 Hz). */
3282 cy_writeb(base_addr + (CyPPR << index), CyCLOCK_60_2MS);
3283 } else {
3284 /* f = 200 Hz */
3285 cy_writeb(base_addr + (CyPPR << index), CyCLOCK_25_5MS);
3286 }
3287
3288 /*
3289 printk(" chip #%d at %#6lx is rev 0x%2x\n",
3290 chip_number, (unsigned long)base_addr,
3291 readb(base_addr+(CyGFRCR<<index)));
3292 */
3293 }
3294 return chip_number;
3295 } /* cyy_init_card */
3296
3297 /*
3298 * ---------------------------------------------------------------------
3299 * cy_detect_isa() - Probe for Cyclom-Y/ISA boards.
3300 * sets global variables and return the number of ISA boards found.
3301 * ---------------------------------------------------------------------
3302 */
3303 static int __init cy_detect_isa(void)
3304 {
3305 #ifdef CONFIG_ISA
3306 unsigned short cy_isa_irq, nboard;
3307 void __iomem *cy_isa_address;
3308 unsigned short i, j, cy_isa_nchan;
3309 int isparam = 0;
3310
3311 nboard = 0;
3312
3313 /* Check for module parameters */
3314 for (i = 0; i < NR_CARDS; i++) {
3315 if (maddr[i] || i) {
3316 isparam = 1;
3317 cy_isa_addresses[i] = maddr[i];
3318 }
3319 if (!maddr[i])
3320 break;
3321 }
3322
3323 /* scan the address table probing for Cyclom-Y/ISA boards */
3324 for (i = 0; i < NR_ISA_ADDRS; i++) {
3325 unsigned int isa_address = cy_isa_addresses[i];
3326 if (isa_address == 0x0000)
3327 return nboard;
3328
3329 /* probe for CD1400... */
3330 cy_isa_address = ioremap_nocache(isa_address, CyISA_Ywin);
3331 if (cy_isa_address == NULL) {
3332 printk(KERN_ERR "Cyclom-Y/ISA: can't remap base "
3333 "address\n");
3334 continue;
3335 }
3336 cy_isa_nchan = CyPORTS_PER_CHIP *
3337 cyy_init_card(cy_isa_address, 0);
3338 if (cy_isa_nchan == 0) {
3339 iounmap(cy_isa_address);
3340 continue;
3341 }
3342
3343 if (isparam && i < NR_CARDS && irq[i])
3344 cy_isa_irq = irq[i];
3345 else
3346 /* find out the board's irq by probing */
3347 cy_isa_irq = detect_isa_irq(cy_isa_address);
3348 if (cy_isa_irq == 0) {
3349 printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but the "
3350 "IRQ could not be detected.\n",
3351 (unsigned long)cy_isa_address);
3352 iounmap(cy_isa_address);
3353 continue;
3354 }
3355
3356 if ((cy_next_channel + cy_isa_nchan) > NR_PORTS) {
3357 printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but no "
3358 "more channels are available. Change NR_PORTS "
3359 "in cyclades.c and recompile kernel.\n",
3360 (unsigned long)cy_isa_address);
3361 iounmap(cy_isa_address);
3362 return nboard;
3363 }
3364 /* fill the next cy_card structure available */
3365 for (j = 0; j < NR_CARDS; j++) {
3366 if (cy_card[j].base_addr == NULL)
3367 break;
3368 }
3369 if (j == NR_CARDS) { /* no more cy_cards available */
3370 printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but no "
3371 "more cards can be used. Change NR_CARDS in "
3372 "cyclades.c and recompile kernel.\n",
3373 (unsigned long)cy_isa_address);
3374 iounmap(cy_isa_address);
3375 return nboard;
3376 }
3377
3378 /* allocate IRQ */
3379 if (request_irq(cy_isa_irq, cyy_interrupt,
3380 IRQF_DISABLED, "Cyclom-Y", &cy_card[j])) {
3381 printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but "
3382 "could not allocate IRQ#%d.\n",
3383 (unsigned long)cy_isa_address, cy_isa_irq);
3384 iounmap(cy_isa_address);
3385 return nboard;
3386 }
3387
3388 /* set cy_card */
3389 cy_card[j].base_addr = cy_isa_address;
3390 cy_card[j].ctl_addr.p9050 = NULL;
3391 cy_card[j].irq = (int)cy_isa_irq;
3392 cy_card[j].bus_index = 0;
3393 cy_card[j].first_line = cy_next_channel;
3394 cy_card[j].num_chips = cy_isa_nchan / CyPORTS_PER_CHIP;
3395 cy_card[j].nports = cy_isa_nchan;
3396 if (cy_init_card(&cy_card[j])) {
3397 cy_card[j].base_addr = NULL;
3398 free_irq(cy_isa_irq, &cy_card[j]);
3399 iounmap(cy_isa_address);
3400 continue;
3401 }
3402 nboard++;
3403
3404 printk(KERN_INFO "Cyclom-Y/ISA #%d: 0x%lx-0x%lx, IRQ%d found: "
3405 "%d channels starting from port %d\n",
3406 j + 1, (unsigned long)cy_isa_address,
3407 (unsigned long)(cy_isa_address + (CyISA_Ywin - 1)),
3408 cy_isa_irq, cy_isa_nchan, cy_next_channel);
3409
3410 for (j = cy_next_channel;
3411 j < cy_next_channel + cy_isa_nchan; j++)
3412 tty_register_device(cy_serial_driver, j, NULL);
3413 cy_next_channel += cy_isa_nchan;
3414 }
3415 return nboard;
3416 #else
3417 return 0;
3418 #endif /* CONFIG_ISA */
3419 } /* cy_detect_isa */
3420
3421 #ifdef CONFIG_PCI
3422 static inline int __devinit cyc_isfwstr(const char *str, unsigned int size)
3423 {
3424 unsigned int a;
3425
3426 for (a = 0; a < size && *str; a++, str++)
3427 if (*str & 0x80)
3428 return -EINVAL;
3429
3430 for (; a < size; a++, str++)
3431 if (*str)
3432 return -EINVAL;
3433
3434 return 0;
3435 }
3436
3437 static inline void __devinit cyz_fpga_copy(void __iomem *fpga, const u8 *data,
3438 unsigned int size)
3439 {
3440 for (; size > 0; size--) {
3441 cy_writel(fpga, *data++);
3442 udelay(10);
3443 }
3444 }
3445
3446 static void __devinit plx_init(struct pci_dev *pdev, int irq,
3447 struct RUNTIME_9060 __iomem *addr)
3448 {
3449 /* Reset PLX */
3450 cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) | 0x40000000);
3451 udelay(100L);
3452 cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) & ~0x40000000);
3453
3454 /* Reload Config. Registers from EEPROM */
3455 cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) | 0x20000000);
3456 udelay(100L);
3457 cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) & ~0x20000000);
3458
3459 /* For some yet unknown reason, once the PLX9060 reloads the EEPROM,
3460 * the IRQ is lost and, thus, we have to re-write it to the PCI config.
3461 * registers. This will remain here until we find a permanent fix.
3462 */
3463 pci_write_config_byte(pdev, PCI_INTERRUPT_LINE, irq);
3464 }
3465
3466 static int __devinit __cyz_load_fw(const struct firmware *fw,
3467 const char *name, const u32 mailbox, void __iomem *base,
3468 void __iomem *fpga)
3469 {
3470 const void *ptr = fw->data;
3471 const struct zfile_header *h = ptr;
3472 const struct zfile_config *c, *cs;
3473 const struct zfile_block *b, *bs;
3474 unsigned int a, tmp, len = fw->size;
3475 #define BAD_FW KERN_ERR "Bad firmware: "
3476 if (len < sizeof(*h)) {
3477 printk(BAD_FW "too short: %u<%zu\n", len, sizeof(*h));
3478 return -EINVAL;
3479 }
3480
3481 cs = ptr + h->config_offset;
3482 bs = ptr + h->block_offset;
3483
3484 if ((void *)(cs + h->n_config) > ptr + len ||
3485 (void *)(bs + h->n_blocks) > ptr + len) {
3486 printk(BAD_FW "too short");
3487 return -EINVAL;
3488 }
3489
3490 if (cyc_isfwstr(h->name, sizeof(h->name)) ||
3491 cyc_isfwstr(h->date, sizeof(h->date))) {
3492 printk(BAD_FW "bad formatted header string\n");
3493 return -EINVAL;
3494 }
3495
3496 if (strncmp(name, h->name, sizeof(h->name))) {
3497 printk(BAD_FW "bad name '%s' (expected '%s')\n", h->name, name);
3498 return -EINVAL;
3499 }
3500
3501 tmp = 0;
3502 for (c = cs; c < cs + h->n_config; c++) {
3503 for (a = 0; a < c->n_blocks; a++)
3504 if (c->block_list[a] > h->n_blocks) {
3505 printk(BAD_FW "bad block ref number in cfgs\n");
3506 return -EINVAL;
3507 }
3508 if (c->mailbox == mailbox && c->function == 0) /* 0 is normal */
3509 tmp++;
3510 }
3511 if (!tmp) {
3512 printk(BAD_FW "nothing appropriate\n");
3513 return -EINVAL;
3514 }
3515
3516 for (b = bs; b < bs + h->n_blocks; b++)
3517 if (b->file_offset + b->size > len) {
3518 printk(BAD_FW "bad block data offset\n");
3519 return -EINVAL;
3520 }
3521
3522 /* everything is OK, let's seek'n'load it */
3523 for (c = cs; c < cs + h->n_config; c++)
3524 if (c->mailbox == mailbox && c->function == 0)
3525 break;
3526
3527 for (a = 0; a < c->n_blocks; a++) {
3528 b = &bs[c->block_list[a]];
3529 if (b->type == ZBLOCK_FPGA) {
3530 if (fpga != NULL)
3531 cyz_fpga_copy(fpga, ptr + b->file_offset,
3532 b->size);
3533 } else {
3534 if (base != NULL)
3535 memcpy_toio(base + b->ram_offset,
3536 ptr + b->file_offset, b->size);
3537 }
3538 }
3539 #undef BAD_FW
3540 return 0;
3541 }
3542
3543 static int __devinit cyz_load_fw(struct pci_dev *pdev, void __iomem *base_addr,
3544 struct RUNTIME_9060 __iomem *ctl_addr, int irq)
3545 {
3546 const struct firmware *fw;
3547 struct FIRM_ID __iomem *fid = base_addr + ID_ADDRESS;
3548 struct CUSTOM_REG __iomem *cust = base_addr;
3549 struct ZFW_CTRL __iomem *pt_zfwctrl;
3550 void __iomem *tmp;
3551 u32 mailbox, status, nchan;
3552 unsigned int i;
3553 int retval;
3554
3555 retval = request_firmware(&fw, "cyzfirm.bin", &pdev->dev);
3556 if (retval) {
3557 dev_err(&pdev->dev, "can't get firmware\n");
3558 goto err;
3559 }
3560
3561 /* Check whether the firmware is already loaded and running. If
3562 positive, skip this board */
3563 if (__cyz_fpga_loaded(ctl_addr) && readl(&fid->signature) == ZFIRM_ID) {
3564 u32 cntval = readl(base_addr + 0x190);
3565
3566 udelay(100);
3567 if (cntval != readl(base_addr + 0x190)) {
3568 /* FW counter is working, FW is running */
3569 dev_dbg(&pdev->dev, "Cyclades-Z FW already loaded. "
3570 "Skipping board.\n");
3571 retval = 0;
3572 goto err_rel;
3573 }
3574 }
3575
3576 /* start boot */
3577 cy_writel(&ctl_addr->intr_ctrl_stat, readl(&ctl_addr->intr_ctrl_stat) &
3578 ~0x00030800UL);
3579
3580 mailbox = readl(&ctl_addr->mail_box_0);
3581
3582 if (mailbox == 0 || __cyz_fpga_loaded(ctl_addr)) {
3583 /* stops CPU and set window to beginning of RAM */
3584 cy_writel(&ctl_addr->loc_addr_base, WIN_CREG);
3585 cy_writel(&cust->cpu_stop, 0);
3586 cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
3587 udelay(100);
3588 }
3589
3590 plx_init(pdev, irq, ctl_addr);
3591
3592 if (mailbox != 0) {
3593 /* load FPGA */
3594 retval = __cyz_load_fw(fw, "Cyclom-Z", mailbox, NULL,
3595 base_addr);
3596 if (retval)
3597 goto err_rel;
3598 if (!__cyz_fpga_loaded(ctl_addr)) {
3599 dev_err(&pdev->dev, "fw upload successful, but fw is "
3600 "not loaded\n");
3601 goto err_rel;
3602 }
3603 }
3604
3605 /* stops CPU and set window to beginning of RAM */
3606 cy_writel(&ctl_addr->loc_addr_base, WIN_CREG);
3607 cy_writel(&cust->cpu_stop, 0);
3608 cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
3609 udelay(100);
3610
3611 /* clear memory */
3612 for (tmp = base_addr; tmp < base_addr + RAM_SIZE; tmp++)
3613 cy_writeb(tmp, 255);
3614 if (mailbox != 0) {
3615 /* set window to last 512K of RAM */
3616 cy_writel(&ctl_addr->loc_addr_base, WIN_RAM + RAM_SIZE);
3617 for (tmp = base_addr; tmp < base_addr + RAM_SIZE; tmp++)
3618 cy_writeb(tmp, 255);
3619 /* set window to beginning of RAM */
3620 cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
3621 }
3622
3623 retval = __cyz_load_fw(fw, "Cyclom-Z", mailbox, base_addr, NULL);
3624 release_firmware(fw);
3625 if (retval)
3626 goto err;
3627
3628 /* finish boot and start boards */
3629 cy_writel(&ctl_addr->loc_addr_base, WIN_CREG);
3630 cy_writel(&cust->cpu_start, 0);
3631 cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
3632 i = 0;
3633 while ((status = readl(&fid->signature)) != ZFIRM_ID && i++ < 40)
3634 msleep(100);
3635 if (status != ZFIRM_ID) {
3636 if (status == ZFIRM_HLT) {
3637 dev_err(&pdev->dev, "you need an external power supply "
3638 "for this number of ports. Firmware halted and "
3639 "board reset.\n");
3640 retval = -EIO;
3641 goto err;
3642 }
3643 dev_warn(&pdev->dev, "fid->signature = 0x%x... Waiting "
3644 "some more time\n", status);
3645 while ((status = readl(&fid->signature)) != ZFIRM_ID &&
3646 i++ < 200)
3647 msleep(100);
3648 if (status != ZFIRM_ID) {
3649 dev_err(&pdev->dev, "Board not started in 20 seconds! "
3650 "Giving up. (fid->signature = 0x%x)\n",
3651 status);
3652 dev_info(&pdev->dev, "*** Warning ***: if you are "
3653 "upgrading the FW, please power cycle the "
3654 "system before loading the new FW to the "
3655 "Cyclades-Z.\n");
3656
3657 if (__cyz_fpga_loaded(ctl_addr))
3658 plx_init(pdev, irq, ctl_addr);
3659
3660 retval = -EIO;
3661 goto err;
3662 }
3663 dev_dbg(&pdev->dev, "Firmware started after %d seconds.\n",
3664 i / 10);
3665 }
3666 pt_zfwctrl = base_addr + readl(&fid->zfwctrl_addr);
3667
3668 dev_dbg(&pdev->dev, "fid=> %p, zfwctrl_addr=> %x, npt_zfwctrl=> %p\n",
3669 base_addr + ID_ADDRESS, readl(&fid->zfwctrl_addr),
3670 base_addr + readl(&fid->zfwctrl_addr));
3671
3672 nchan = readl(&pt_zfwctrl->board_ctrl.n_channel);
3673 dev_info(&pdev->dev, "Cyclades-Z FW loaded: version = %x, ports = %u\n",
3674 readl(&pt_zfwctrl->board_ctrl.fw_version), nchan);
3675
3676 if (nchan == 0) {
3677 dev_warn(&pdev->dev, "no Cyclades-Z ports were found. Please "
3678 "check the connection between the Z host card and the "
3679 "serial expanders.\n");
3680
3681 if (__cyz_fpga_loaded(ctl_addr))
3682 plx_init(pdev, irq, ctl_addr);
3683
3684 dev_info(&pdev->dev, "Null number of ports detected. Board "
3685 "reset.\n");
3686 retval = 0;
3687 goto err;
3688 }
3689
3690 cy_writel(&pt_zfwctrl->board_ctrl.op_system, C_OS_LINUX);
3691 cy_writel(&pt_zfwctrl->board_ctrl.dr_version, DRIVER_VERSION);
3692
3693 /*
3694 Early firmware failed to start looking for commands.
3695 This enables firmware interrupts for those commands.
3696 */
3697 cy_writel(&ctl_addr->intr_ctrl_stat, readl(&ctl_addr->intr_ctrl_stat) |
3698 (1 << 17));
3699 cy_writel(&ctl_addr->intr_ctrl_stat, readl(&ctl_addr->intr_ctrl_stat) |
3700 0x00030800UL);
3701
3702 return nchan;
3703 err_rel:
3704 release_firmware(fw);
3705 err:
3706 return retval;
3707 }
3708
3709 static int __devinit cy_pci_probe(struct pci_dev *pdev,
3710 const struct pci_device_id *ent)
3711 {
3712 void __iomem *addr0 = NULL, *addr2 = NULL;
3713 char *card_name = NULL;
3714 u32 uninitialized_var(mailbox);
3715 unsigned int device_id, nchan = 0, card_no, i;
3716 unsigned char plx_ver;
3717 int retval, irq;
3718
3719 retval = pci_enable_device(pdev);
3720 if (retval) {
3721 dev_err(&pdev->dev, "cannot enable device\n");
3722 goto err;
3723 }
3724
3725 /* read PCI configuration area */
3726 irq = pdev->irq;
3727 device_id = pdev->device & ~PCI_DEVICE_ID_MASK;
3728
3729 #if defined(__alpha__)
3730 if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo) { /* below 1M? */
3731 dev_err(&pdev->dev, "Cyclom-Y/PCI not supported for low "
3732 "addresses on Alpha systems.\n");
3733 retval = -EIO;
3734 goto err_dis;
3735 }
3736 #endif
3737 if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Lo) {
3738 dev_err(&pdev->dev, "Cyclades-Z/PCI not supported for low "
3739 "addresses\n");
3740 retval = -EIO;
3741 goto err_dis;
3742 }
3743
3744 if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
3745 dev_warn(&pdev->dev, "PCI I/O bit incorrectly set. Ignoring "
3746 "it...\n");
3747 pdev->resource[2].flags &= ~IORESOURCE_IO;
3748 }
3749
3750 retval = pci_request_regions(pdev, "cyclades");
3751 if (retval) {
3752 dev_err(&pdev->dev, "failed to reserve resources\n");
3753 goto err_dis;
3754 }
3755
3756 retval = -EIO;
3757 if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
3758 device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
3759 card_name = "Cyclom-Y";
3760
3761 addr0 = ioremap_nocache(pci_resource_start(pdev, 0),
3762 CyPCI_Yctl);
3763 if (addr0 == NULL) {
3764 dev_err(&pdev->dev, "can't remap ctl region\n");
3765 goto err_reg;
3766 }
3767 addr2 = ioremap_nocache(pci_resource_start(pdev, 2),
3768 CyPCI_Ywin);
3769 if (addr2 == NULL) {
3770 dev_err(&pdev->dev, "can't remap base region\n");
3771 goto err_unmap;
3772 }
3773
3774 nchan = CyPORTS_PER_CHIP * cyy_init_card(addr2, 1);
3775 if (nchan == 0) {
3776 dev_err(&pdev->dev, "Cyclom-Y PCI host card with no "
3777 "Serial-Modules\n");
3778 goto err_unmap;
3779 }
3780 } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Hi) {
3781 struct RUNTIME_9060 __iomem *ctl_addr;
3782
3783 ctl_addr = addr0 = ioremap_nocache(pci_resource_start(pdev, 0),
3784 CyPCI_Zctl);
3785 if (addr0 == NULL) {
3786 dev_err(&pdev->dev, "can't remap ctl region\n");
3787 goto err_reg;
3788 }
3789
3790 /* Disable interrupts on the PLX before resetting it */
3791 cy_writew(&ctl_addr->intr_ctrl_stat,
3792 readw(&ctl_addr->intr_ctrl_stat) & ~0x0900);
3793
3794 plx_init(pdev, irq, addr0);
3795
3796 mailbox = readl(&ctl_addr->mail_box_0);
3797
3798 addr2 = ioremap_nocache(pci_resource_start(pdev, 2),
3799 mailbox == ZE_V1 ? CyPCI_Ze_win : CyPCI_Zwin);
3800 if (addr2 == NULL) {
3801 dev_err(&pdev->dev, "can't remap base region\n");
3802 goto err_unmap;
3803 }
3804
3805 if (mailbox == ZE_V1) {
3806 card_name = "Cyclades-Ze";
3807 } else {
3808 card_name = "Cyclades-8Zo";
3809 #ifdef CY_PCI_DEBUG
3810 if (mailbox == ZO_V1) {
3811 cy_writel(&ctl_addr->loc_addr_base, WIN_CREG);
3812 dev_info(&pdev->dev, "Cyclades-8Zo/PCI: FPGA "
3813 "id %lx, ver %lx\n", (ulong)(0xff &
3814 readl(&((struct CUSTOM_REG *)addr2)->
3815 fpga_id)), (ulong)(0xff &
3816 readl(&((struct CUSTOM_REG *)addr2)->
3817 fpga_version)));
3818 cy_writel(&ctl_addr->loc_addr_base, WIN_RAM);
3819 } else {
3820 dev_info(&pdev->dev, "Cyclades-Z/PCI: New "
3821 "Cyclades-Z board. FPGA not loaded\n");
3822 }
3823 #endif
3824 /* The following clears the firmware id word. This
3825 ensures that the driver will not attempt to talk to
3826 the board until it has been properly initialized.
3827 */
3828 if ((mailbox == ZO_V1) || (mailbox == ZO_V2))
3829 cy_writel(addr2 + ID_ADDRESS, 0L);
3830 }
3831
3832 retval = cyz_load_fw(pdev, addr2, addr0, irq);
3833 if (retval <= 0)
3834 goto err_unmap;
3835 nchan = retval;
3836 }
3837
3838 if ((cy_next_channel + nchan) > NR_PORTS) {
3839 dev_err(&pdev->dev, "Cyclades-8Zo/PCI found, but no "
3840 "channels are available. Change NR_PORTS in "
3841 "cyclades.c and recompile kernel.\n");
3842 goto err_unmap;
3843 }
3844 /* fill the next cy_card structure available */
3845 for (card_no = 0; card_no < NR_CARDS; card_no++) {
3846 if (cy_card[card_no].base_addr == NULL)
3847 break;
3848 }
3849 if (card_no == NR_CARDS) { /* no more cy_cards available */
3850 dev_err(&pdev->dev, "Cyclades-8Zo/PCI found, but no "
3851 "more cards can be used. Change NR_CARDS in "
3852 "cyclades.c and recompile kernel.\n");
3853 goto err_unmap;
3854 }
3855
3856 if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
3857 device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
3858 /* allocate IRQ */
3859 retval = request_irq(irq, cyy_interrupt,
3860 IRQF_SHARED, "Cyclom-Y", &cy_card[card_no]);
3861 if (retval) {
3862 dev_err(&pdev->dev, "could not allocate IRQ\n");
3863 goto err_unmap;
3864 }
3865 cy_card[card_no].num_chips = nchan / CyPORTS_PER_CHIP;
3866 } else {
3867 struct FIRM_ID __iomem *firm_id = addr2 + ID_ADDRESS;
3868 struct ZFW_CTRL __iomem *zfw_ctrl;
3869
3870 zfw_ctrl = addr2 + (readl(&firm_id->zfwctrl_addr) & 0xfffff);
3871
3872 cy_card[card_no].hw_ver = mailbox;
3873 cy_card[card_no].num_chips = (unsigned int)-1;
3874 cy_card[card_no].board_ctrl = &zfw_ctrl->board_ctrl;
3875 #ifdef CONFIG_CYZ_INTR
3876 /* allocate IRQ only if board has an IRQ */
3877 if (irq != 0 && irq != 255) {
3878 retval = request_irq(irq, cyz_interrupt,
3879 IRQF_SHARED, "Cyclades-Z",
3880 &cy_card[card_no]);
3881 if (retval) {
3882 dev_err(&pdev->dev, "could not allocate IRQ\n");
3883 goto err_unmap;
3884 }
3885 }
3886 #endif /* CONFIG_CYZ_INTR */
3887 }
3888
3889 /* set cy_card */
3890 cy_card[card_no].base_addr = addr2;
3891 cy_card[card_no].ctl_addr.p9050 = addr0;
3892 cy_card[card_no].irq = irq;
3893 cy_card[card_no].bus_index = 1;
3894 cy_card[card_no].first_line = cy_next_channel;
3895 cy_card[card_no].nports = nchan;
3896 retval = cy_init_card(&cy_card[card_no]);
3897 if (retval)
3898 goto err_null;
3899
3900 pci_set_drvdata(pdev, &cy_card[card_no]);
3901
3902 if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
3903 device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
3904 /* enable interrupts in the PCI interface */
3905 plx_ver = readb(addr2 + CyPLX_VER) & 0x0f;
3906 switch (plx_ver) {
3907 case PLX_9050:
3908 cy_writeb(addr0 + 0x4c, 0x43);
3909 break;
3910
3911 case PLX_9060:
3912 case PLX_9080:
3913 default: /* Old boards, use PLX_9060 */
3914 {
3915 struct RUNTIME_9060 __iomem *ctl_addr = addr0;
3916 plx_init(pdev, irq, ctl_addr);
3917 cy_writew(&ctl_addr->intr_ctrl_stat,
3918 readw(&ctl_addr->intr_ctrl_stat) | 0x0900);
3919 break;
3920 }
3921 }
3922 }
3923
3924 dev_info(&pdev->dev, "%s/PCI #%d found: %d channels starting from "
3925 "port %d.\n", card_name, card_no + 1, nchan, cy_next_channel);
3926 for (i = cy_next_channel; i < cy_next_channel + nchan; i++)
3927 tty_register_device(cy_serial_driver, i, &pdev->dev);
3928 cy_next_channel += nchan;
3929
3930 return 0;
3931 err_null:
3932 cy_card[card_no].base_addr = NULL;
3933 free_irq(irq, &cy_card[card_no]);
3934 err_unmap:
3935 iounmap(addr0);
3936 if (addr2)
3937 iounmap(addr2);
3938 err_reg:
3939 pci_release_regions(pdev);
3940 err_dis:
3941 pci_disable_device(pdev);
3942 err:
3943 return retval;
3944 }
3945
3946 static void __devexit cy_pci_remove(struct pci_dev *pdev)
3947 {
3948 struct cyclades_card *cinfo = pci_get_drvdata(pdev);
3949 unsigned int i;
3950
3951 /* non-Z with old PLX */
3952 if (!cy_is_Z(cinfo) && (readb(cinfo->base_addr + CyPLX_VER) & 0x0f) ==
3953 PLX_9050)
3954 cy_writeb(cinfo->ctl_addr.p9050 + 0x4c, 0);
3955 else
3956 #ifndef CONFIG_CYZ_INTR
3957 if (!cy_is_Z(cinfo))
3958 #endif
3959 cy_writew(&cinfo->ctl_addr.p9060->intr_ctrl_stat,
3960 readw(&cinfo->ctl_addr.p9060->intr_ctrl_stat) &
3961 ~0x0900);
3962
3963 iounmap(cinfo->base_addr);
3964 if (cinfo->ctl_addr.p9050)
3965 iounmap(cinfo->ctl_addr.p9050);
3966 if (cinfo->irq
3967 #ifndef CONFIG_CYZ_INTR
3968 && !cy_is_Z(cinfo)
3969 #endif /* CONFIG_CYZ_INTR */
3970 )
3971 free_irq(cinfo->irq, cinfo);
3972 pci_release_regions(pdev);
3973
3974 cinfo->base_addr = NULL;
3975 for (i = cinfo->first_line; i < cinfo->first_line +
3976 cinfo->nports; i++)
3977 tty_unregister_device(cy_serial_driver, i);
3978 cinfo->nports = 0;
3979 kfree(cinfo->ports);
3980 }
3981
3982 static struct pci_driver cy_pci_driver = {
3983 .name = "cyclades",
3984 .id_table = cy_pci_dev_id,
3985 .probe = cy_pci_probe,
3986 .remove = __devexit_p(cy_pci_remove)
3987 };
3988 #endif
3989
3990 static int cyclades_proc_show(struct seq_file *m, void *v)
3991 {
3992 struct cyclades_port *info;
3993 unsigned int i, j;
3994 __u32 cur_jifs = jiffies;
3995
3996 seq_puts(m, "Dev TimeOpen BytesOut IdleOut BytesIn "
3997 "IdleIn Overruns Ldisc\n");
3998
3999 /* Output one line for each known port */
4000 for (i = 0; i < NR_CARDS; i++)
4001 for (j = 0; j < cy_card[i].nports; j++) {
4002 info = &cy_card[i].ports[j];
4003
4004 if (info->port.count) {
4005 /* XXX is the ldisc num worth this? */
4006 struct tty_struct *tty;
4007 struct tty_ldisc *ld;
4008 int num = 0;
4009 tty = tty_port_tty_get(&info->port);
4010 if (tty) {
4011 ld = tty_ldisc_ref(tty);
4012 if (ld) {
4013 num = ld->ops->num;
4014 tty_ldisc_deref(ld);
4015 }
4016 tty_kref_put(tty);
4017 }
4018 seq_printf(m, "%3d %8lu %10lu %8lu "
4019 "%10lu %8lu %9lu %6d\n", info->line,
4020 (cur_jifs - info->idle_stats.in_use) /
4021 HZ, info->idle_stats.xmit_bytes,
4022 (cur_jifs - info->idle_stats.xmit_idle)/
4023 HZ, info->idle_stats.recv_bytes,
4024 (cur_jifs - info->idle_stats.recv_idle)/
4025 HZ, info->idle_stats.overruns,
4026 num);
4027 } else
4028 seq_printf(m, "%3d %8lu %10lu %8lu "
4029 "%10lu %8lu %9lu %6ld\n",
4030 info->line, 0L, 0L, 0L, 0L, 0L, 0L, 0L);
4031 }
4032 return 0;
4033 }
4034
4035 static int cyclades_proc_open(struct inode *inode, struct file *file)
4036 {
4037 return single_open(file, cyclades_proc_show, NULL);
4038 }
4039
4040 static const struct file_operations cyclades_proc_fops = {
4041 .owner = THIS_MODULE,
4042 .open = cyclades_proc_open,
4043 .read = seq_read,
4044 .llseek = seq_lseek,
4045 .release = single_release,
4046 };
4047
4048 /* The serial driver boot-time initialization code!
4049 Hardware I/O ports are mapped to character special devices on a
4050 first found, first allocated manner. That is, this code searches
4051 for Cyclom cards in the system. As each is found, it is probed
4052 to discover how many chips (and thus how many ports) are present.
4053 These ports are mapped to the tty ports 32 and upward in monotonic
4054 fashion. If an 8-port card is replaced with a 16-port card, the
4055 port mapping on a following card will shift.
4056
4057 This approach is different from what is used in the other serial
4058 device driver because the Cyclom is more properly a multiplexer,
4059 not just an aggregation of serial ports on one card.
4060
4061 If there are more cards with more ports than have been
4062 statically allocated above, a warning is printed and the
4063 extra ports are ignored.
4064 */
4065
4066 static const struct tty_operations cy_ops = {
4067 .open = cy_open,
4068 .close = cy_close,
4069 .write = cy_write,
4070 .put_char = cy_put_char,
4071 .flush_chars = cy_flush_chars,
4072 .write_room = cy_write_room,
4073 .chars_in_buffer = cy_chars_in_buffer,
4074 .flush_buffer = cy_flush_buffer,
4075 .ioctl = cy_ioctl,
4076 .throttle = cy_throttle,
4077 .unthrottle = cy_unthrottle,
4078 .set_termios = cy_set_termios,
4079 .stop = cy_stop,
4080 .start = cy_start,
4081 .hangup = cy_hangup,
4082 .break_ctl = cy_break,
4083 .wait_until_sent = cy_wait_until_sent,
4084 .tiocmget = cy_tiocmget,
4085 .tiocmset = cy_tiocmset,
4086 .get_icount = cy_get_icount,
4087 .proc_fops = &cyclades_proc_fops,
4088 };
4089
4090 static int __init cy_init(void)
4091 {
4092 unsigned int nboards;
4093 int retval = -ENOMEM;
4094
4095 cy_serial_driver = alloc_tty_driver(NR_PORTS);
4096 if (!cy_serial_driver)
4097 goto err;
4098
4099 printk(KERN_INFO "Cyclades driver " CY_VERSION "\n");
4100
4101 /* Initialize the tty_driver structure */
4102
4103 cy_serial_driver->owner = THIS_MODULE;
4104 cy_serial_driver->driver_name = "cyclades";
4105 cy_serial_driver->name = "ttyC";
4106 cy_serial_driver->major = CYCLADES_MAJOR;
4107 cy_serial_driver->minor_start = 0;
4108 cy_serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
4109 cy_serial_driver->subtype = SERIAL_TYPE_NORMAL;
4110 cy_serial_driver->init_termios = tty_std_termios;
4111 cy_serial_driver->init_termios.c_cflag =
4112 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
4113 cy_serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
4114 tty_set_operations(cy_serial_driver, &cy_ops);
4115
4116 retval = tty_register_driver(cy_serial_driver);
4117 if (retval) {
4118 printk(KERN_ERR "Couldn't register Cyclades serial driver\n");
4119 goto err_frtty;
4120 }
4121
4122 /* the code below is responsible to find the boards. Each different
4123 type of board has its own detection routine. If a board is found,
4124 the next cy_card structure available is set by the detection
4125 routine. These functions are responsible for checking the
4126 availability of cy_card and cy_port data structures and updating
4127 the cy_next_channel. */
4128
4129 /* look for isa boards */
4130 nboards = cy_detect_isa();
4131
4132 #ifdef CONFIG_PCI
4133 /* look for pci boards */
4134 retval = pci_register_driver(&cy_pci_driver);
4135 if (retval && !nboards) {
4136 tty_unregister_driver(cy_serial_driver);
4137 goto err_frtty;
4138 }
4139 #endif
4140
4141 return 0;
4142 err_frtty:
4143 put_tty_driver(cy_serial_driver);
4144 err:
4145 return retval;
4146 } /* cy_init */
4147
4148 static void __exit cy_cleanup_module(void)
4149 {
4150 struct cyclades_card *card;
4151 unsigned int i, e1;
4152
4153 #ifndef CONFIG_CYZ_INTR
4154 del_timer_sync(&cyz_timerlist);
4155 #endif /* CONFIG_CYZ_INTR */
4156
4157 e1 = tty_unregister_driver(cy_serial_driver);
4158 if (e1)
4159 printk(KERN_ERR "failed to unregister Cyclades serial "
4160 "driver(%d)\n", e1);
4161
4162 #ifdef CONFIG_PCI
4163 pci_unregister_driver(&cy_pci_driver);
4164 #endif
4165
4166 for (i = 0; i < NR_CARDS; i++) {
4167 card = &cy_card[i];
4168 if (card->base_addr) {
4169 /* clear interrupt */
4170 cy_writeb(card->base_addr + Cy_ClrIntr, 0);
4171 iounmap(card->base_addr);
4172 if (card->ctl_addr.p9050)
4173 iounmap(card->ctl_addr.p9050);
4174 if (card->irq
4175 #ifndef CONFIG_CYZ_INTR
4176 && !cy_is_Z(card)
4177 #endif /* CONFIG_CYZ_INTR */
4178 )
4179 free_irq(card->irq, card);
4180 for (e1 = card->first_line; e1 < card->first_line +
4181 card->nports; e1++)
4182 tty_unregister_device(cy_serial_driver, e1);
4183 kfree(card->ports);
4184 }
4185 }
4186
4187 put_tty_driver(cy_serial_driver);
4188 } /* cy_cleanup_module */
4189
4190 module_init(cy_init);
4191 module_exit(cy_cleanup_module);
4192
4193 MODULE_LICENSE("GPL");
4194 MODULE_VERSION(CY_VERSION);
4195 MODULE_ALIAS_CHARDEV_MAJOR(CYCLADES_MAJOR);
4196 MODULE_FIRMWARE("cyzfirm.bin");
Linux Btrfs Development