arch/arm/plat-iop/pci.c

   1 /*
   2  * arch/arm/plat-iop/pci.c
   3  *
   4  * PCI support for the Intel IOP32X and IOP33X processors
   5  *
   6  * Author: Rory Bolt <rorybolt@pacbell.net>
   7  * Copyright (C) 2002 Rory Bolt
   8  *
   9  * This program is free software; you can redistribute it and/or modify
  10  * it under the terms of the GNU General Public License version 2 as
  11  * published by the Free Software Foundation.
  12  */
  13
  14 #include <linux/kernel.h>
  15 #include <linux/pci.h>
  16 #include <linux/slab.h>
  17 #include <linux/mm.h>
  18 #include <linux/init.h>
  19 #include <linux/ioport.h>
  20 #include <linux/io.h>
  21 #include <asm/irq.h>
  22 #include <asm/signal.h>
  23 #include <asm/system.h>
  24 #include <mach/hardware.h>
  25 #include <asm/mach/pci.h>
  26 #include <asm/hardware/iop3xx.h>
  27
  28 // #define DEBUG
  29
  30 #ifdef DEBUG
  31 #define  DBG(x...) printk(x)
  32 #else
  33 #define  DBG(x...) do { } while (0)
  34 #endif
  35
  36 /*
  37  * This routine builds either a type0 or type1 configuration command.  If the
  38  * bus is on the 803xx then a type0 made, else a type1 is created.
  39  */
  40 static u32 iop3xx_cfg_address(struct pci_bus *bus, int devfn, int where)
  41 {
  42         struct pci_sys_data *sys = bus->sysdata;
  43         u32 addr;
  44
  45         if (sys->busnr == bus->number)
  46                 addr = 1 << (PCI_SLOT(devfn) + 16) | (PCI_SLOT(devfn) << 11);
  47         else
  48                 addr = bus->number << 16 | PCI_SLOT(devfn) << 11 | 1;
  49
  50         addr |= PCI_FUNC(devfn) << 8 | (where & ~3);
  51
  52         return addr;
  53 }
  54
  55 /*
  56  * This routine checks the status of the last configuration cycle.  If an error
  57  * was detected it returns a 1, else it returns a 0.  The errors being checked
  58  * are parity, master abort, target abort (master and target).  These types of
  59  * errors occur during a config cycle where there is no device, like during
  60  * the discovery stage.
  61  */
  62 static int iop3xx_pci_status(void)
  63 {
  64         unsigned int status;
  65         int ret = 0;
  66
  67         /*
  68          * Check the status registers.
  69          */
  70         status = *IOP3XX_ATUSR;
  71         if (status & 0xf900) {
  72                 DBG("\t\t\tPCI: P0 - status = 0x%08x\n", status);
  73                 *IOP3XX_ATUSR = status & 0xf900;
  74                 ret = 1;
  75         }
  76
  77         status = *IOP3XX_ATUISR;
  78         if (status & 0x679f) {
  79                 DBG("\t\t\tPCI: P1 - status = 0x%08x\n", status);
  80                 *IOP3XX_ATUISR = status & 0x679f;
  81                 ret = 1;
  82         }
  83
  84         return ret;
  85 }
  86
  87 /*
  88  * Simply write the address register and read the configuration
  89  * data.  Note that the 4 nops ensure that we are able to handle
  90  * a delayed abort (in theory.)
  91  */
  92 static u32 iop3xx_read(unsigned long addr)
  93 {
  94         u32 val;
  95
  96         __asm__ __volatile__(
  97                 "str    %1, [%2]\n\t"
  98                 "ldr    %0, [%3]\n\t"
  99                 "nop\n\t"
 100                 "nop\n\t"
 101                 "nop\n\t"
 102                 "nop\n\t"
 103                 : "=r" (val)
 104                 : "r" (addr), "r" (IOP3XX_OCCAR), "r" (IOP3XX_OCCDR));
 105
 106         return val;
 107 }
 108
 109 /*
 110  * The read routines must check the error status of the last configuration
 111  * cycle.  If there was an error, the routine returns all hex f's.
 112  */
 113 static int
 114 iop3xx_read_config(struct pci_bus *bus, unsigned int devfn, int where,
 115                 int size, u32 *value)
 116 {
 117         unsigned long addr = iop3xx_cfg_address(bus, devfn, where);
 118         u32 val = iop3xx_read(addr) >> ((where & 3) * 8);
 119
 120         if (iop3xx_pci_status())
 121                 val = 0xffffffff;
 122
 123         *value = val;
 124
 125         return PCIBIOS_SUCCESSFUL;
 126 }
 127
 128 static int
 129 iop3xx_write_config(struct pci_bus *bus, unsigned int devfn, int where,
 130                 int size, u32 value)
 131 {
 132         unsigned long addr = iop3xx_cfg_address(bus, devfn, where);
 133         u32 val;
 134
 135         if (size != 4) {
 136                 val = iop3xx_read(addr);
 137                 if (iop3xx_pci_status())
 138                         return PCIBIOS_SUCCESSFUL;
 139
 140                 where = (where & 3) * 8;
 141
 142                 if (size == 1)
 143                         val &= ~(0xff << where);
 144                 else
 145                         val &= ~(0xffff << where);
 146
 147                 *IOP3XX_OCCDR = val | value << where;
 148         } else {
 149                 asm volatile(
 150                         "str    %1, [%2]\n\t"
 151                         "str    %0, [%3]\n\t"
 152                         "nop\n\t"
 153                         "nop\n\t"
 154                         "nop\n\t"
 155                         "nop\n\t"
 156                         :
 157                         : "r" (value), "r" (addr),
 158                           "r" (IOP3XX_OCCAR), "r" (IOP3XX_OCCDR));
 159         }
 160
 161         return PCIBIOS_SUCCESSFUL;
 162 }
 163
 164 static struct pci_ops iop3xx_ops = {
 165         .read   = iop3xx_read_config,
 166         .write  = iop3xx_write_config,
 167 };
 168
 169 /*
 170  * When a PCI device does not exist during config cycles, the 80200 gets a
 171  * bus error instead of returning 0xffffffff. This handler simply returns.
 172  */
 173 static int
 174 iop3xx_pci_abort(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 175 {
 176         DBG("PCI abort: address = 0x%08lx fsr = 0x%03x PC = 0x%08lx LR = 0x%08lx\n",
 177                 addr, fsr, regs->ARM_pc, regs->ARM_lr);
 178
 179         /*
 180          * If it was an imprecise abort, then we need to correct the
 181          * return address to be _after_ the instruction.
 182          */
 183         if (fsr & (1 << 10))
 184                 regs->ARM_pc += 4;
 185
 186         return 0;
 187 }
 188
 189 int iop3xx_pci_setup(int nr, struct pci_sys_data *sys)
 190 {
 191         struct resource *res;
 192
 193         if (nr != 0)
 194                 return 0;
 195
 196         res = kzalloc(2 * sizeof(struct resource), GFP_KERNEL);
 197         if (!res)
 198                 panic("PCI: unable to alloc resources");
 199
 200         res[0].start = IOP3XX_PCI_LOWER_IO_PA;
 201         res[0].end   = IOP3XX_PCI_LOWER_IO_PA + IOP3XX_PCI_IO_WINDOW_SIZE - 1;
 202         res[0].name  = "IOP3XX PCI I/O Space";
 203         res[0].flags = IORESOURCE_IO;
 204         request_resource(&ioport_resource, &res[0]);
 205
 206         res[1].start = IOP3XX_PCI_LOWER_MEM_PA;
 207         res[1].end   = IOP3XX_PCI_LOWER_MEM_PA + IOP3XX_PCI_MEM_WINDOW_SIZE - 1;
 208         res[1].name  = "IOP3XX PCI Memory Space";
 209         res[1].flags = IORESOURCE_MEM;
 210         request_resource(&iomem_resource, &res[1]);
 211
 212         /*
 213          * Use whatever translation is already setup.
 214          */
 215         sys->mem_offset = IOP3XX_PCI_LOWER_MEM_PA - *IOP3XX_OMWTVR0;
 216         sys->io_offset  = IOP3XX_PCI_LOWER_IO_PA - *IOP3XX_OIOWTVR;
 217
 218         sys->resource[0] = &res[0];
 219         sys->resource[1] = &res[1];
 220         sys->resource[2] = NULL;
 221
 222         return 1;
 223 }
 224
 225 struct pci_bus *iop3xx_pci_scan_bus(int nr, struct pci_sys_data *sys)
 226 {
 227         return pci_scan_bus(sys->busnr, &iop3xx_ops, sys);
 228 }
 229
 230 void __init iop3xx_atu_setup(void)
 231 {
 232         /* BAR 0 ( Disabled ) */
 233         *IOP3XX_IAUBAR0 = 0x0;
 234         *IOP3XX_IABAR0  = 0x0;
 235         *IOP3XX_IATVR0  = 0x0;
 236         *IOP3XX_IALR0   = 0x0;
 237
 238         /* BAR 1 ( Disabled ) */
 239         *IOP3XX_IAUBAR1 = 0x0;
 240         *IOP3XX_IABAR1  = 0x0;
 241         *IOP3XX_IALR1   = 0x0;
 242
 243         /* BAR 2 (1:1 mapping with Physical RAM) */
 244         /* Set limit and enable */
 245         *IOP3XX_IALR2 = ~((u32)IOP3XX_MAX_RAM_SIZE - 1) & ~0x1;
 246         *IOP3XX_IAUBAR2 = 0x0;
 247
 248         /* Align the inbound bar with the base of memory */
 249         *IOP3XX_IABAR2 = PHYS_OFFSET |
 250                                PCI_BASE_ADDRESS_MEM_TYPE_64 |
 251                                PCI_BASE_ADDRESS_MEM_PREFETCH;
 252
 253         *IOP3XX_IATVR2 = PHYS_OFFSET;
 254
 255         /* Outbound window 0 */
 256         *IOP3XX_OMWTVR0 = IOP3XX_PCI_LOWER_MEM_BA;
 257         *IOP3XX_OUMWTVR0 = 0;
 258
 259         /* Outbound window 1 */
 260         *IOP3XX_OMWTVR1 = IOP3XX_PCI_LOWER_MEM_BA +
 261                           IOP3XX_PCI_MEM_WINDOW_SIZE / 2;
 262         *IOP3XX_OUMWTVR1 = 0;
 263
 264         /* BAR 3 ( Disabled ) */
 265         *IOP3XX_IAUBAR3 = 0x0;
 266         *IOP3XX_IABAR3  = 0x0;
 267         *IOP3XX_IATVR3  = 0x0;
 268         *IOP3XX_IALR3   = 0x0;
 269
 270         /* Setup the I/O Bar
 271          */
 272         *IOP3XX_OIOWTVR = IOP3XX_PCI_LOWER_IO_BA;
 273
 274         /* Enable inbound and outbound cycles
 275          */
 276         *IOP3XX_ATUCMD |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER |
 277                                PCI_COMMAND_PARITY | PCI_COMMAND_SERR;
 278         *IOP3XX_ATUCR |= IOP3XX_ATUCR_OUT_EN;
 279 }
 280
 281 void __init iop3xx_atu_disable(void)
 282 {
 283         *IOP3XX_ATUCMD = 0;
 284         *IOP3XX_ATUCR = 0;
 285
 286         /* wait for cycles to quiesce */
 287         while (*IOP3XX_PCSR & (IOP3XX_PCSR_OUT_Q_BUSY |
 288                                      IOP3XX_PCSR_IN_Q_BUSY))
 289                 cpu_relax();
 290
 291         /* BAR 0 ( Disabled ) */
 292         *IOP3XX_IAUBAR0 = 0x0;
 293         *IOP3XX_IABAR0  = 0x0;
 294         *IOP3XX_IATVR0  = 0x0;
 295         *IOP3XX_IALR0   = 0x0;
 296
 297         /* BAR 1 ( Disabled ) */
 298         *IOP3XX_IAUBAR1 = 0x0;
 299         *IOP3XX_IABAR1  = 0x0;
 300         *IOP3XX_IALR1   = 0x0;
 301
 302         /* BAR 2 ( Disabled ) */
 303         *IOP3XX_IAUBAR2 = 0x0;
 304         *IOP3XX_IABAR2  = 0x0;
 305         *IOP3XX_IATVR2  = 0x0;
 306         *IOP3XX_IALR2   = 0x0;
 307
 308         /* BAR 3 ( Disabled ) */
 309         *IOP3XX_IAUBAR3 = 0x0;
 310         *IOP3XX_IABAR3  = 0x0;
 311         *IOP3XX_IATVR3  = 0x0;
 312         *IOP3XX_IALR3   = 0x0;
 313
 314         /* Clear the outbound windows */
 315         *IOP3XX_OIOWTVR  = 0;
 316
 317         /* Outbound window 0 */
 318         *IOP3XX_OMWTVR0 = 0;
 319         *IOP3XX_OUMWTVR0 = 0;
 320
 321         /* Outbound window 1 */
 322         *IOP3XX_OMWTVR1 = 0;
 323         *IOP3XX_OUMWTVR1 = 0;
 324 }
 325
 326 /* Flag to determine whether the ATU is initialized and the PCI bus scanned */
 327 int init_atu;
 328
 329 int iop3xx_get_init_atu(void) {
 330         /* check if default has been overridden */
 331         if (init_atu != IOP3XX_INIT_ATU_DEFAULT)
 332                 return init_atu;
 333         else
 334                 return IOP3XX_INIT_ATU_DISABLE;
 335 }
 336
 337 static void __init iop3xx_atu_debug(void)
 338 {
 339         DBG("PCI: Intel IOP3xx PCI init.\n");
 340         DBG("PCI: Outbound memory window 0: PCI 0x%08x%08x\n",
 341                 *IOP3XX_OUMWTVR0, *IOP3XX_OMWTVR0);
 342         DBG("PCI: Outbound memory window 1: PCI 0x%08x%08x\n",
 343                 *IOP3XX_OUMWTVR1, *IOP3XX_OMWTVR1);
 344         DBG("PCI: Outbound IO window: PCI 0x%08x\n",
 345                 *IOP3XX_OIOWTVR);
 346
 347         DBG("PCI: Inbound memory window 0: PCI 0x%08x%08x 0x%08x -> 0x%08x\n",
 348                 *IOP3XX_IAUBAR0, *IOP3XX_IABAR0, *IOP3XX_IALR0, *IOP3XX_IATVR0);
 349         DBG("PCI: Inbound memory window 1: PCI 0x%08x%08x 0x%08x\n",
 350                 *IOP3XX_IAUBAR1, *IOP3XX_IABAR1, *IOP3XX_IALR1);
 351         DBG("PCI: Inbound memory window 2: PCI 0x%08x%08x 0x%08x -> 0x%08x\n",
 352                 *IOP3XX_IAUBAR2, *IOP3XX_IABAR2, *IOP3XX_IALR2, *IOP3XX_IATVR2);
 353         DBG("PCI: Inbound memory window 3: PCI 0x%08x%08x 0x%08x -> 0x%08x\n",
 354                 *IOP3XX_IAUBAR3, *IOP3XX_IABAR3, *IOP3XX_IALR3, *IOP3XX_IATVR3);
 355
 356         DBG("PCI: Expansion ROM window: PCI 0x%08x%08x 0x%08x -> 0x%08x\n",
 357                 0, *IOP3XX_ERBAR, *IOP3XX_ERLR, *IOP3XX_ERTVR);
 358
 359         DBG("ATU: IOP3XX_ATUCMD=0x%04x\n", *IOP3XX_ATUCMD);
 360         DBG("ATU: IOP3XX_ATUCR=0x%08x\n", *IOP3XX_ATUCR);
 361
 362         hook_fault_code(16+6, iop3xx_pci_abort, SIGBUS, 0, "imprecise external abort");
 363 }
 364
 365 /* for platforms that might be host-bus-adapters */
 366 void __init iop3xx_pci_preinit_cond(void)
 367 {
 368         if (iop3xx_get_init_atu() == IOP3XX_INIT_ATU_ENABLE) {
 369                 iop3xx_atu_disable();
 370                 iop3xx_atu_setup();
 371                 iop3xx_atu_debug();
 372         }
 373 }
 374
 375 void __init iop3xx_pci_preinit(void)
 376 {
 377         pcibios_min_io = 0;
 378         pcibios_min_mem = 0;
 379
 380         iop3xx_atu_disable();
 381         iop3xx_atu_setup();
 382         iop3xx_atu_debug();
 383 }
 384
 385 /* allow init_atu to be user overridden */
 386 static int __init iop3xx_init_atu_setup(char *str)
 387 {
 388         init_atu = IOP3XX_INIT_ATU_DEFAULT;
 389         if (str) {
 390                 while (*str != '\0') {
 391                         switch (*str) {
 392                         case 'y':
 393                         case 'Y':
 394                                 init_atu = IOP3XX_INIT_ATU_ENABLE;
 395                                 break;
 396                         case 'n':
 397                         case 'N':
 398                                 init_atu = IOP3XX_INIT_ATU_DISABLE;
 399                                 break;
 400                         case ',':
 401                         case '=':
 402                                 break;
 403                         default:
 404                                 printk(KERN_DEBUG "\"%s\" malformed at "
 405                                             "character: \'%c\'",
 406                                             __func__,
 407                                             *str);
 408                                 *(str + 1) = '\0';
 409                         }
 410                         str++;
 411                 }
 412         }
 413
 414         return 1;
 415 }
 416
 417 __setup("iop3xx_init_atu", iop3xx_init_atu_setup);
 418