net/mac80211/rc80211_pid_algo.c

   1 /*
   2  * Copyright 2002-2005, Instant802 Networks, Inc.
   3  * Copyright 2005, Devicescape Software, Inc.
   4  * Copyright 2007, Mattias Nissler <mattias.nissler@gmx.de>
   5  * Copyright 2007-2008, Stefano Brivio <stefano.brivio@polimi.it>
   6  *
   7  * This program is free software; you can redistribute it and/or modify
   8  * it under the terms of the GNU General Public License version 2 as
   9  * published by the Free Software Foundation.
  10  */
  11
  12 #include <linux/netdevice.h>
  13 #include <linux/types.h>
  14 #include <linux/skbuff.h>
  15 #include <linux/debugfs.h>
  16 #include <net/mac80211.h>
  17 #include "rate.h"
  18 #include "mesh.h"
  19 #include "rc80211_pid.h"
  20
  21
  22 /* This is an implementation of a TX rate control algorithm that uses a PID
  23  * controller. Given a target failed frames rate, the controller decides about
  24  * TX rate changes to meet the target failed frames rate.
  25  *
  26  * The controller basically computes the following:
  27  *
  28  * adj = CP * err + CI * err_avg + CD * (err - last_err) * (1 + sharpening)
  29  *
  30  * where
  31  *      adj     adjustment value that is used to switch TX rate (see below)
  32  *      err     current error: target vs. current failed frames percentage
  33  *      last_err        last error
  34  *      err_avg average (i.e. poor man's integral) of recent errors
  35  *      sharpening      non-zero when fast response is needed (i.e. right after
  36  *                      association or no frames sent for a long time), heading
  37  *                      to zero over time
  38  *      CP      Proportional coefficient
  39  *      CI      Integral coefficient
  40  *      CD      Derivative coefficient
  41  *
  42  * CP, CI, CD are subject to careful tuning.
  43  *
  44  * The integral component uses a exponential moving average approach instead of
  45  * an actual sliding window. The advantage is that we don't need to keep an
  46  * array of the last N error values and computation is easier.
  47  *
  48  * Once we have the adj value, we map it to a rate by means of a learning
  49  * algorithm. This algorithm keeps the state of the percentual failed frames
  50  * difference between rates. The behaviour of the lowest available rate is kept
  51  * as a reference value, and every time we switch between two rates, we compute
  52  * the difference between the failed frames each rate exhibited. By doing so,
  53  * we compare behaviours which different rates exhibited in adjacent timeslices,
  54  * thus the comparison is minimally affected by external conditions. This
  55  * difference gets propagated to the whole set of measurements, so that the
  56  * reference is always the same. Periodically, we normalize this set so that
  57  * recent events weigh the most. By comparing the adj value with this set, we
  58  * avoid pejorative switches to lower rates and allow for switches to higher
  59  * rates if they behaved well.
  60  *
  61  * Note that for the computations we use a fixed-point representation to avoid
  62  * floating point arithmetic. Hence, all values are shifted left by
  63  * RC_PID_ARITH_SHIFT.
  64  */
  65
  66
  67 /* Adjust the rate while ensuring that we won't switch to a lower rate if it
  68  * exhibited a worse failed frames behaviour and we'll choose the highest rate
  69  * whose failed frames behaviour is not worse than the one of the original rate
  70  * target. While at it, check that the new rate is valid. */
  71 static void rate_control_pid_adjust_rate(struct ieee80211_supported_band *sband,
  72                                          struct ieee80211_sta *sta,
  73                                          struct rc_pid_sta_info *spinfo, int adj,
  74                                          struct rc_pid_rateinfo *rinfo)
  75 {
  76         int cur_sorted, new_sorted, probe, tmp, n_bitrates, band;
  77         int cur = spinfo->txrate_idx;
  78
  79         band = sband->band;
  80         n_bitrates = sband->n_bitrates;
  81
  82         /* Map passed arguments to sorted values. */
  83         cur_sorted = rinfo[cur].rev_index;
  84         new_sorted = cur_sorted + adj;
  85
  86         /* Check limits. */
  87         if (new_sorted < 0)
  88                 new_sorted = rinfo[0].rev_index;
  89         else if (new_sorted >= n_bitrates)
  90                 new_sorted = rinfo[n_bitrates - 1].rev_index;
  91
  92         tmp = new_sorted;
  93
  94         if (adj < 0) {
  95                 /* Ensure that the rate decrease isn't disadvantageous. */
  96                 for (probe = cur_sorted; probe >= new_sorted; probe--)
  97                         if (rinfo[probe].diff <= rinfo[cur_sorted].diff &&
  98                             rate_supported(sta, band, rinfo[probe].index))
  99                                 tmp = probe;
 100         } else {
 101                 /* Look for rate increase with zero (or below) cost. */
 102                 for (probe = new_sorted + 1; probe < n_bitrates; probe++)
 103                         if (rinfo[probe].diff <= rinfo[new_sorted].diff &&
 104                             rate_supported(sta, band, rinfo[probe].index))
 105                                 tmp = probe;
 106         }
 107
 108         /* Fit the rate found to the nearest supported rate. */
 109         do {
 110                 if (rate_supported(sta, band, rinfo[tmp].index)) {
 111                         spinfo->txrate_idx = rinfo[tmp].index;
 112                         break;
 113                 }
 114                 if (adj < 0)
 115                         tmp--;
 116                 else
 117                         tmp++;
 118         } while (tmp < n_bitrates && tmp >= 0);
 119
 120 #ifdef CONFIG_MAC80211_DEBUGFS
 121         rate_control_pid_event_rate_change(&spinfo->events,
 122                 spinfo->txrate_idx,
 123                 sband->bitrates[spinfo->txrate_idx].bitrate);
 124 #endif
 125 }
 126
 127 /* Normalize the failed frames per-rate differences. */
 128 static void rate_control_pid_normalize(struct rc_pid_info *pinfo, int l)
 129 {
 130         int i, norm_offset = pinfo->norm_offset;
 131         struct rc_pid_rateinfo *r = pinfo->rinfo;
 132
 133         if (r[0].diff > norm_offset)
 134                 r[0].diff -= norm_offset;
 135         else if (r[0].diff < -norm_offset)
 136                 r[0].diff += norm_offset;
 137         for (i = 0; i < l - 1; i++)
 138                 if (r[i + 1].diff > r[i].diff + norm_offset)
 139                         r[i + 1].diff -= norm_offset;
 140                 else if (r[i + 1].diff <= r[i].diff)
 141                         r[i + 1].diff += norm_offset;
 142 }
 143
 144 static void rate_control_pid_sample(struct rc_pid_info *pinfo,
 145                                     struct ieee80211_supported_band *sband,
 146                                     struct ieee80211_sta *sta,
 147                                     struct rc_pid_sta_info *spinfo)
 148 {
 149         struct rc_pid_rateinfo *rinfo = pinfo->rinfo;
 150         u32 pf;
 151         s32 err_avg;
 152         u32 err_prop;
 153         u32 err_int;
 154         u32 err_der;
 155         int adj, i, j, tmp;
 156         unsigned long period;
 157
 158         /* In case nothing happened during the previous control interval, turn
 159          * the sharpening factor on. */
 160         period = (HZ * pinfo->sampling_period + 500) / 1000;
 161         if (!period)
 162                 period = 1;
 163         if (jiffies - spinfo->last_sample > 2 * period)
 164                 spinfo->sharp_cnt = pinfo->sharpen_duration;
 165
 166         spinfo->last_sample = jiffies;
 167
 168         /* This should never happen, but in case, we assume the old sample is
 169          * still a good measurement and copy it. */
 170         if (unlikely(spinfo->tx_num_xmit == 0))
 171                 pf = spinfo->last_pf;
 172         else {
 173                 /* XXX: BAD HACK!!! */
 174                 struct sta_info *si = container_of(sta, struct sta_info, sta);
 175
 176                 pf = spinfo->tx_num_failed * 100 / spinfo->tx_num_xmit;
 177
 178                 if (ieee80211_vif_is_mesh(&si->sdata->vif) && pf == 100)
 179                         mesh_plink_broken(si);
 180                 pf <<= RC_PID_ARITH_SHIFT;
 181                 si->fail_avg = ((pf + (spinfo->last_pf << 3)) / 9)
 182                                         >> RC_PID_ARITH_SHIFT;
 183         }
 184
 185         spinfo->tx_num_xmit = 0;
 186         spinfo->tx_num_failed = 0;
 187
 188         /* If we just switched rate, update the rate behaviour info. */
 189         if (pinfo->oldrate != spinfo->txrate_idx) {
 190
 191                 i = rinfo[pinfo->oldrate].rev_index;
 192                 j = rinfo[spinfo->txrate_idx].rev_index;
 193
 194                 tmp = (pf - spinfo->last_pf);
 195                 tmp = RC_PID_DO_ARITH_RIGHT_SHIFT(tmp, RC_PID_ARITH_SHIFT);
 196
 197                 rinfo[j].diff = rinfo[i].diff + tmp;
 198                 pinfo->oldrate = spinfo->txrate_idx;
 199         }
 200         rate_control_pid_normalize(pinfo, sband->n_bitrates);
 201
 202         /* Compute the proportional, integral and derivative errors. */
 203         err_prop = (pinfo->target << RC_PID_ARITH_SHIFT) - pf;
 204
 205         err_avg = spinfo->err_avg_sc >> pinfo->smoothing_shift;
 206         spinfo->err_avg_sc = spinfo->err_avg_sc - err_avg + err_prop;
 207         err_int = spinfo->err_avg_sc >> pinfo->smoothing_shift;
 208
 209         err_der = (pf - spinfo->last_pf) *
 210                   (1 + pinfo->sharpen_factor * spinfo->sharp_cnt);
 211         spinfo->last_pf = pf;
 212         if (spinfo->sharp_cnt)
 213                         spinfo->sharp_cnt--;
 214
 215 #ifdef CONFIG_MAC80211_DEBUGFS
 216         rate_control_pid_event_pf_sample(&spinfo->events, pf, err_prop, err_int,
 217                                          err_der);
 218 #endif
 219
 220         /* Compute the controller output. */
 221         adj = (err_prop * pinfo->coeff_p + err_int * pinfo->coeff_i
 222               + err_der * pinfo->coeff_d);
 223         adj = RC_PID_DO_ARITH_RIGHT_SHIFT(adj, 2 * RC_PID_ARITH_SHIFT);
 224
 225         /* Change rate. */
 226         if (adj)
 227                 rate_control_pid_adjust_rate(sband, sta, spinfo, adj, rinfo);
 228 }
 229
 230 static void rate_control_pid_tx_status(void *priv, struct ieee80211_supported_band *sband,
 231                                        struct ieee80211_sta *sta, void *priv_sta,
 232                                        struct sk_buff *skb)
 233 {
 234         struct rc_pid_info *pinfo = priv;
 235         struct rc_pid_sta_info *spinfo = priv_sta;
 236         unsigned long period;
 237         struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
 238
 239         if (!spinfo)
 240                 return;
 241
 242         /* Ignore all frames that were sent with a different rate than the rate
 243          * we currently advise mac80211 to use. */
 244         if (info->status.rates[0].idx != spinfo->txrate_idx)
 245                 return;
 246
 247         spinfo->tx_num_xmit++;
 248
 249 #ifdef CONFIG_MAC80211_DEBUGFS
 250         rate_control_pid_event_tx_status(&spinfo->events, info);
 251 #endif
 252
 253         /* We count frames that totally failed to be transmitted as two bad
 254          * frames, those that made it out but had some retries as one good and
 255          * one bad frame. */
 256         if (!(info->flags & IEEE80211_TX_STAT_ACK)) {
 257                 spinfo->tx_num_failed += 2;
 258                 spinfo->tx_num_xmit++;
 259         } else if (info->status.rates[0].count > 1) {
 260                 spinfo->tx_num_failed++;
 261                 spinfo->tx_num_xmit++;
 262         }
 263
 264         /* Update PID controller state. */
 265         period = (HZ * pinfo->sampling_period + 500) / 1000;
 266         if (!period)
 267                 period = 1;
 268         if (time_after(jiffies, spinfo->last_sample + period))
 269                 rate_control_pid_sample(pinfo, sband, sta, spinfo);
 270 }
 271
 272 static void
 273 rate_control_pid_get_rate(void *priv, struct ieee80211_sta *sta,
 274                           void *priv_sta,
 275                           struct ieee80211_tx_rate_control *txrc)
 276 {
 277         struct sk_buff *skb = txrc->skb;
 278         struct ieee80211_supported_band *sband = txrc->sband;
 279         struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
 280         struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
 281         struct rc_pid_sta_info *spinfo = priv_sta;
 282         int rateidx;
 283         u16 fc;
 284
 285         if (txrc->rts)
 286                 info->control.rates[0].count =
 287                         txrc->hw->conf.long_frame_max_tx_count;
 288         else
 289                 info->control.rates[0].count =
 290                         txrc->hw->conf.short_frame_max_tx_count;
 291
 292         /* Send management frames and broadcast/multicast data using lowest
 293          * rate. */
 294         fc = le16_to_cpu(hdr->frame_control);
 295         if (!sta || !spinfo ||
 296             (fc & IEEE80211_FCTL_FTYPE) != IEEE80211_FTYPE_DATA ||
 297             is_multicast_ether_addr(hdr->addr1)) {
 298                 info->control.rates[0].idx = rate_lowest_index(sband, sta);
 299                 return;
 300         }
 301
 302         rateidx = spinfo->txrate_idx;
 303
 304         if (rateidx >= sband->n_bitrates)
 305                 rateidx = sband->n_bitrates - 1;
 306
 307         info->control.rates[0].idx = rateidx;
 308
 309 #ifdef CONFIG_MAC80211_DEBUGFS
 310         rate_control_pid_event_tx_rate(&spinfo->events,
 311                 rateidx, sband->bitrates[rateidx].bitrate);
 312 #endif
 313 }
 314
 315 static void
 316 rate_control_pid_rate_init(void *priv, struct ieee80211_supported_band *sband,
 317                            struct ieee80211_sta *sta, void *priv_sta)
 318 {
 319         struct rc_pid_sta_info *spinfo = priv_sta;
 320         struct rc_pid_info *pinfo = priv;
 321         struct rc_pid_rateinfo *rinfo = pinfo->rinfo;
 322         struct sta_info *si;
 323         int i, j, tmp;
 324         bool s;
 325
 326         /* TODO: This routine should consider using RSSI from previous packets
 327          * as we need to have IEEE 802.1X auth succeed immediately after assoc..
 328          * Until that method is implemented, we will use the lowest supported
 329          * rate as a workaround. */
 330
 331         /* Sort the rates. This is optimized for the most common case (i.e.
 332          * almost-sorted CCK+OFDM rates). Kind of bubble-sort with reversed
 333          * mapping too. */
 334         for (i = 0; i < sband->n_bitrates; i++) {
 335                 rinfo[i].index = i;
 336                 rinfo[i].rev_index = i;
 337                 if (RC_PID_FAST_START)
 338                         rinfo[i].diff = 0;
 339                 else
 340                         rinfo[i].diff = i * pinfo->norm_offset;
 341         }
 342         for (i = 1; i < sband->n_bitrates; i++) {
 343                 s = 0;
 344                 for (j = 0; j < sband->n_bitrates - i; j++)
 345                         if (unlikely(sband->bitrates[rinfo[j].index].bitrate >
 346                                      sband->bitrates[rinfo[j + 1].index].bitrate)) {
 347                                 tmp = rinfo[j].index;
 348                                 rinfo[j].index = rinfo[j + 1].index;
 349                                 rinfo[j + 1].index = tmp;
 350                                 rinfo[rinfo[j].index].rev_index = j;
 351                                 rinfo[rinfo[j + 1].index].rev_index = j + 1;
 352                                 s = 1;
 353                         }
 354                 if (!s)
 355                         break;
 356         }
 357
 358         spinfo->txrate_idx = rate_lowest_index(sband, sta);
 359         /* HACK */
 360         si = container_of(sta, struct sta_info, sta);
 361         si->fail_avg = 0;
 362 }
 363
 364 static void *rate_control_pid_alloc(struct ieee80211_hw *hw,
 365                                     struct dentry *debugfsdir)
 366 {
 367         struct rc_pid_info *pinfo;
 368         struct rc_pid_rateinfo *rinfo;
 369         struct ieee80211_supported_band *sband;
 370         int i, max_rates = 0;
 371 #ifdef CONFIG_MAC80211_DEBUGFS
 372         struct rc_pid_debugfs_entries *de;
 373 #endif
 374
 375         pinfo = kmalloc(sizeof(*pinfo), GFP_ATOMIC);
 376         if (!pinfo)
 377                 return NULL;
 378
 379         for (i = 0; i < IEEE80211_NUM_BANDS; i++) {
 380                 sband = hw->wiphy->bands[i];
 381                 if (sband && sband->n_bitrates > max_rates)
 382                         max_rates = sband->n_bitrates;
 383         }
 384
 385         rinfo = kmalloc(sizeof(*rinfo) * max_rates, GFP_ATOMIC);
 386         if (!rinfo) {
 387                 kfree(pinfo);
 388                 return NULL;
 389         }
 390
 391         pinfo->target = RC_PID_TARGET_PF;
 392         pinfo->sampling_period = RC_PID_INTERVAL;
 393         pinfo->coeff_p = RC_PID_COEFF_P;
 394         pinfo->coeff_i = RC_PID_COEFF_I;
 395         pinfo->coeff_d = RC_PID_COEFF_D;
 396         pinfo->smoothing_shift = RC_PID_SMOOTHING_SHIFT;
 397         pinfo->sharpen_factor = RC_PID_SHARPENING_FACTOR;
 398         pinfo->sharpen_duration = RC_PID_SHARPENING_DURATION;
 399         pinfo->norm_offset = RC_PID_NORM_OFFSET;
 400         pinfo->rinfo = rinfo;
 401         pinfo->oldrate = 0;
 402
 403 #ifdef CONFIG_MAC80211_DEBUGFS
 404         de = &pinfo->dentries;
 405         de->target = debugfs_create_u32("target_pf", S_IRUSR | S_IWUSR,
 406                                         debugfsdir, &pinfo->target);
 407         de->sampling_period = debugfs_create_u32("sampling_period",
 408                                                  S_IRUSR | S_IWUSR, debugfsdir,
 409                                                  &pinfo->sampling_period);
 410         de->coeff_p = debugfs_create_u32("coeff_p", S_IRUSR | S_IWUSR,
 411                                          debugfsdir, (u32 *)&pinfo->coeff_p);
 412         de->coeff_i = debugfs_create_u32("coeff_i", S_IRUSR | S_IWUSR,
 413                                          debugfsdir, (u32 *)&pinfo->coeff_i);
 414         de->coeff_d = debugfs_create_u32("coeff_d", S_IRUSR | S_IWUSR,
 415                                          debugfsdir, (u32 *)&pinfo->coeff_d);
 416         de->smoothing_shift = debugfs_create_u32("smoothing_shift",
 417                                                  S_IRUSR | S_IWUSR, debugfsdir,
 418                                                  &pinfo->smoothing_shift);
 419         de->sharpen_factor = debugfs_create_u32("sharpen_factor",
 420                                                S_IRUSR | S_IWUSR, debugfsdir,
 421                                                &pinfo->sharpen_factor);
 422         de->sharpen_duration = debugfs_create_u32("sharpen_duration",
 423                                                   S_IRUSR | S_IWUSR, debugfsdir,
 424                                                   &pinfo->sharpen_duration);
 425         de->norm_offset = debugfs_create_u32("norm_offset",
 426                                              S_IRUSR | S_IWUSR, debugfsdir,
 427                                              &pinfo->norm_offset);
 428 #endif
 429
 430         return pinfo;
 431 }
 432
 433 static void rate_control_pid_free(void *priv)
 434 {
 435         struct rc_pid_info *pinfo = priv;
 436 #ifdef CONFIG_MAC80211_DEBUGFS
 437         struct rc_pid_debugfs_entries *de = &pinfo->dentries;
 438
 439         debugfs_remove(de->norm_offset);
 440         debugfs_remove(de->sharpen_duration);
 441         debugfs_remove(de->sharpen_factor);
 442         debugfs_remove(de->smoothing_shift);
 443         debugfs_remove(de->coeff_d);
 444         debugfs_remove(de->coeff_i);
 445         debugfs_remove(de->coeff_p);
 446         debugfs_remove(de->sampling_period);
 447         debugfs_remove(de->target);
 448 #endif
 449
 450         kfree(pinfo->rinfo);
 451         kfree(pinfo);
 452 }
 453
 454 static void *rate_control_pid_alloc_sta(void *priv, struct ieee80211_sta *sta,
 455                                         gfp_t gfp)
 456 {
 457         struct rc_pid_sta_info *spinfo;
 458
 459         spinfo = kzalloc(sizeof(*spinfo), gfp);
 460         if (spinfo == NULL)
 461                 return NULL;
 462
 463         spinfo->last_sample = jiffies;
 464
 465 #ifdef CONFIG_MAC80211_DEBUGFS
 466         spin_lock_init(&spinfo->events.lock);
 467         init_waitqueue_head(&spinfo->events.waitqueue);
 468 #endif
 469
 470         return spinfo;
 471 }
 472
 473 static void rate_control_pid_free_sta(void *priv, struct ieee80211_sta *sta,
 474                                       void *priv_sta)
 475 {
 476         kfree(priv_sta);
 477 }
 478
 479 static struct rate_control_ops mac80211_rcpid = {
 480         .name = "pid",
 481         .tx_status = rate_control_pid_tx_status,
 482         .get_rate = rate_control_pid_get_rate,
 483         .rate_init = rate_control_pid_rate_init,
 484         .alloc = rate_control_pid_alloc,
 485         .free = rate_control_pid_free,
 486         .alloc_sta = rate_control_pid_alloc_sta,
 487         .free_sta = rate_control_pid_free_sta,
 488 #ifdef CONFIG_MAC80211_DEBUGFS
 489         .add_sta_debugfs = rate_control_pid_add_sta_debugfs,
 490         .remove_sta_debugfs = rate_control_pid_remove_sta_debugfs,
 491 #endif
 492 };
 493
 494 int __init rc80211_pid_init(void)
 495 {
 496         return ieee80211_rate_control_register(&mac80211_rcpid);
 497 }
 498
 499 void rc80211_pid_exit(void)
 500 {
 501         ieee80211_rate_control_unregister(&mac80211_rcpid);
 502 }