OMAP3: PM: Ensure MUSB block can idle when driver not loaded
[linux-ginger.git] / arch / arm / mach-pxa / e750.c
blob1d00110590e5c7dee25cca9918e1c6591a798526
1 /*
2 * Hardware definitions for the Toshiba eseries PDAs
4 * Copyright (c) 2003 Ian Molton <spyro@f2s.com>
6 * This file is licensed under
7 * the terms of the GNU General Public License version 2. This program
8 * is licensed "as is" without any warranty of any kind, whether express
9 * or implied.
13 #include <linux/kernel.h>
14 #include <linux/init.h>
15 #include <linux/device.h>
16 #include <linux/platform_device.h>
17 #include <linux/fb.h>
18 #include <linux/mfd/tc6393xb.h>
20 #include <video/w100fb.h>
22 #include <asm/setup.h>
23 #include <asm/mach/arch.h>
24 #include <asm/mach-types.h>
26 #include <mach/pxa25x.h>
27 #include <mach/eseries-gpio.h>
28 #include <mach/udc.h>
29 #include <mach/irda.h>
30 #include <mach/irqs.h>
31 #include <mach/audio.h>
33 #include "generic.h"
34 #include "eseries.h"
35 #include "clock.h"
37 /* ---------------------- E750 LCD definitions -------------------- */
39 static struct w100_gen_regs e750_lcd_regs = {
40 .lcd_format = 0x00008003,
41 .lcdd_cntl1 = 0x00000000,
42 .lcdd_cntl2 = 0x0003ffff,
43 .genlcd_cntl1 = 0x00fff003,
44 .genlcd_cntl2 = 0x003c0f03,
45 .genlcd_cntl3 = 0x000143aa,
48 static struct w100_mode e750_lcd_mode = {
49 .xres = 240,
50 .yres = 320,
51 .left_margin = 21,
52 .right_margin = 22,
53 .upper_margin = 5,
54 .lower_margin = 4,
55 .crtc_ss = 0x80150014,
56 .crtc_ls = 0x8014000d,
57 .crtc_gs = 0xc1000005,
58 .crtc_vpos_gs = 0x00020147,
59 .crtc_rev = 0x0040010a,
60 .crtc_dclk = 0xa1700030,
61 .crtc_gclk = 0x80cc0015,
62 .crtc_goe = 0x80cc0015,
63 .crtc_ps1_active = 0x61060017,
64 .pll_freq = 57,
65 .pixclk_divider = 4,
66 .pixclk_divider_rotated = 4,
67 .pixclk_src = CLK_SRC_XTAL,
68 .sysclk_divider = 1,
69 .sysclk_src = CLK_SRC_PLL,
72 static struct w100_gpio_regs e750_w100_gpio_info = {
73 .init_data1 = 0x01192f1b,
74 .gpio_dir1 = 0xd5ffdeff,
75 .gpio_oe1 = 0x000020bf,
76 .init_data2 = 0x010f010f,
77 .gpio_dir2 = 0xffffffff,
78 .gpio_oe2 = 0x000001cf,
81 static struct w100fb_mach_info e750_fb_info = {
82 .modelist = &e750_lcd_mode,
83 .num_modes = 1,
84 .regs = &e750_lcd_regs,
85 .gpio = &e750_w100_gpio_info,
86 .xtal_freq = 14318000,
87 .xtal_dbl = 1,
90 static struct resource e750_fb_resources[] = {
91 [0] = {
92 .start = 0x0c000000,
93 .end = 0x0cffffff,
94 .flags = IORESOURCE_MEM,
98 static struct platform_device e750_fb_device = {
99 .name = "w100fb",
100 .id = -1,
101 .dev = {
102 .platform_data = &e750_fb_info,
104 .num_resources = ARRAY_SIZE(e750_fb_resources),
105 .resource = e750_fb_resources,
108 /* -------------------- e750 MFP parameters -------------------- */
110 static unsigned long e750_pin_config[] __initdata = {
111 /* Chip selects */
112 GPIO15_nCS_1, /* CS1 - Flash */
113 GPIO79_nCS_3, /* CS3 - IMAGEON */
114 GPIO80_nCS_4, /* CS4 - TMIO */
116 /* Clocks */
117 GPIO11_3_6MHz,
119 /* BTUART */
120 GPIO42_BTUART_RXD,
121 GPIO43_BTUART_TXD,
122 GPIO44_BTUART_CTS,
124 /* TMIO controller */
125 GPIO19_GPIO, /* t7l66xb #PCLR */
126 GPIO45_GPIO, /* t7l66xb #SUSPEND (NOT BTUART!) */
128 /* UDC */
129 GPIO13_GPIO,
130 GPIO3_GPIO,
132 /* IrDA */
133 GPIO38_GPIO | MFP_LPM_DRIVE_HIGH,
135 /* Audio power control */
136 GPIO4_GPIO, /* Headphone amp power */
137 GPIO7_GPIO, /* Speaker amp power */
138 GPIO37_GPIO, /* Headphone detect */
140 /* PC Card */
141 GPIO8_GPIO, /* CD0 */
142 GPIO44_GPIO, /* CD1 */
143 GPIO11_GPIO, /* IRQ0 */
144 GPIO6_GPIO, /* IRQ1 */
145 GPIO27_GPIO, /* RST0 */
146 GPIO24_GPIO, /* RST1 */
147 GPIO20_GPIO, /* PWR0 */
148 GPIO23_GPIO, /* PWR1 */
149 GPIO48_nPOE,
150 GPIO49_nPWE,
151 GPIO50_nPIOR,
152 GPIO51_nPIOW,
153 GPIO52_nPCE_1,
154 GPIO53_nPCE_2,
155 GPIO54_nPSKTSEL,
156 GPIO55_nPREG,
157 GPIO56_nPWAIT,
158 GPIO57_nIOIS16,
160 /* wakeup */
161 GPIO0_GPIO | WAKEUP_ON_EDGE_RISE,
164 /* ----------------- e750 tc6393xb parameters ------------------ */
166 static struct tc6393xb_platform_data e750_tc6393xb_info = {
167 .irq_base = IRQ_BOARD_START,
168 .scr_pll2cr = 0x0cc1,
169 .scr_gper = 0,
170 .gpio_base = -1,
171 .suspend = &eseries_tmio_suspend,
172 .resume = &eseries_tmio_resume,
173 .enable = &eseries_tmio_enable,
174 .disable = &eseries_tmio_disable,
177 static struct platform_device e750_tc6393xb_device = {
178 .name = "tc6393xb",
179 .id = -1,
180 .dev = {
181 .platform_data = &e750_tc6393xb_info,
183 .num_resources = 2,
184 .resource = eseries_tmio_resources,
187 /* ------------------------------------------------------------- */
189 static struct platform_device *devices[] __initdata = {
190 &e750_fb_device,
191 &e750_tc6393xb_device,
194 static void __init e750_init(void)
196 pxa2xx_mfp_config(ARRAY_AND_SIZE(e750_pin_config));
197 clk_add_alias("CLK_CK3P6MI", e750_tc6393xb_device.name,
198 "GPIO11_CLK", NULL),
199 eseries_get_tmio_gpios();
200 platform_add_devices(devices, ARRAY_SIZE(devices));
201 pxa_set_udc_info(&e7xx_udc_mach_info);
202 pxa_set_ac97_info(NULL);
203 e7xx_irda_init();
204 pxa_set_ficp_info(&e7xx_ficp_platform_data);
207 MACHINE_START(E750, "Toshiba e750")
208 /* Maintainer: Ian Molton (spyro@f2s.com) */
209 .phys_io = 0x40000000,
210 .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
211 .boot_params = 0xa0000100,
212 .map_io = pxa_map_io,
213 .init_irq = pxa25x_init_irq,
214 .fixup = eseries_fixup,
215 .init_machine = e750_init,
216 .timer = &pxa_timer,
217 MACHINE_END