Full support for Ginger Console
[linux-ginger.git] / arch / arm / mach-at91 / include / mach / board.h
blob2f4fcedc02ba6a55638f5b44c0e5234f8acd887b
1 /*
2 * arch/arm/mach-at91/include/mach/board.h
4 * Copyright (C) 2005 HP Labs
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or
9 * (at your option) any later version.
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
22 * These are data structures found in platform_device.dev.platform_data,
23 * and describing board-specific data needed by drivers. For example,
24 * which pin is used for a given GPIO role.
26 * In 2.6, drivers should strongly avoid board-specific knowledge so
27 * that supporting new boards normally won't require driver patches.
28 * Most board-specific knowledge should be in arch/.../board-*.c files.
31 #ifndef __ASM_ARCH_BOARD_H
32 #define __ASM_ARCH_BOARD_H
34 #include <linux/mtd/partitions.h>
35 #include <linux/device.h>
36 #include <linux/i2c.h>
37 #include <linux/leds.h>
38 #include <linux/spi/spi.h>
39 #include <linux/usb/atmel_usba_udc.h>
40 #include <linux/atmel-mci.h>
41 #include <sound/atmel-ac97c.h>
43 /* USB Device */
44 struct at91_udc_data {
45 u8 vbus_pin; /* high == host powering us */
46 u8 pullup_pin; /* active == D+ pulled up */
47 u8 pullup_active_low; /* true == pullup_pin is active low */
49 extern void __init at91_add_device_udc(struct at91_udc_data *data);
51 /* USB High Speed Device */
52 extern void __init at91_add_device_usba(struct usba_platform_data *data);
54 /* Compact Flash */
55 struct at91_cf_data {
56 u8 irq_pin; /* I/O IRQ */
57 u8 det_pin; /* Card detect */
58 u8 vcc_pin; /* power switching */
59 u8 rst_pin; /* card reset */
60 u8 chipselect; /* EBI Chip Select number */
61 u8 flags;
62 #define AT91_CF_TRUE_IDE 0x01
63 #define AT91_IDE_SWAP_A0_A2 0x02
65 extern void __init at91_add_device_cf(struct at91_cf_data *data);
67 /* MMC / SD */
68 /* at91_mci platform config */
69 struct at91_mmc_data {
70 u8 det_pin; /* card detect IRQ */
71 unsigned slot_b:1; /* uses Slot B */
72 unsigned wire4:1; /* (SD) supports DAT0..DAT3 */
73 u8 wp_pin; /* (SD) writeprotect detect */
74 u8 vcc_pin; /* power switching (high == on) */
76 extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
78 /* atmel-mci platform config */
79 extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data);
81 /* Ethernet (EMAC & MACB) */
82 struct at91_eth_data {
83 u32 phy_mask;
84 u8 phy_irq_pin; /* PHY IRQ */
85 u8 is_rmii; /* using RMII interface? */
87 extern void __init at91_add_device_eth(struct at91_eth_data *data);
89 #if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) \
90 || defined(CONFIG_ARCH_AT91SAM9G45)
91 #define eth_platform_data at91_eth_data
92 #endif
94 /* USB Host */
95 struct at91_usbh_data {
96 u8 ports; /* number of ports on root hub */
97 u8 vbus_pin[2]; /* port power-control pin */
99 extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
100 extern void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data);
102 /* NAND / SmartMedia */
103 struct atmel_nand_data {
104 u8 enable_pin; /* chip enable */
105 u8 det_pin; /* card detect */
106 u8 rdy_pin; /* ready/busy */
107 u8 rdy_pin_active_low; /* rdy_pin value is inverted */
108 u8 ale; /* address line number connected to ALE */
109 u8 cle; /* address line number connected to CLE */
110 u8 bus_width_16; /* buswidth is 16 bit */
111 struct mtd_partition* (*partition_info)(int, int*);
113 extern void __init at91_add_device_nand(struct atmel_nand_data *data);
115 /* I2C*/
116 #if defined(CONFIG_ARCH_AT91SAM9G45)
117 extern void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices);
118 #else
119 extern void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices);
120 #endif
122 /* SPI */
123 extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
125 /* Serial */
126 #define ATMEL_UART_CTS 0x01
127 #define ATMEL_UART_RTS 0x02
128 #define ATMEL_UART_DSR 0x04
129 #define ATMEL_UART_DTR 0x08
130 #define ATMEL_UART_DCD 0x10
131 #define ATMEL_UART_RI 0x20
133 extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
134 extern void __init at91_set_serial_console(unsigned portnr);
136 struct at91_uart_config {
137 unsigned short console_tty; /* tty number of serial console */
138 unsigned short nr_tty; /* number of serial tty's */
139 short tty_map[]; /* map UART to tty number */
141 extern struct platform_device *atmel_default_console_device;
142 extern void __init __deprecated at91_init_serial(struct at91_uart_config *config);
144 struct atmel_uart_data {
145 short use_dma_tx; /* use transmit DMA? */
146 short use_dma_rx; /* use receive DMA? */
147 void __iomem *regs; /* virtual base address, if any */
149 extern void __init at91_add_device_serial(void);
152 * PWM
154 #define AT91_PWM0 0
155 #define AT91_PWM1 1
156 #define AT91_PWM2 2
157 #define AT91_PWM3 3
159 extern void __init at91_add_device_pwm(u32 mask);
162 * SSC -- accessed through ssc_request(id). Drivers don't bind to SSC
163 * platform devices. Their SSC ID is part of their configuration data,
164 * along with information about which SSC signals they should use.
166 #define ATMEL_SSC_TK 0x01
167 #define ATMEL_SSC_TF 0x02
168 #define ATMEL_SSC_TD 0x04
169 #define ATMEL_SSC_TX (ATMEL_SSC_TK | ATMEL_SSC_TF | ATMEL_SSC_TD)
171 #define ATMEL_SSC_RK 0x10
172 #define ATMEL_SSC_RF 0x20
173 #define ATMEL_SSC_RD 0x40
174 #define ATMEL_SSC_RX (ATMEL_SSC_RK | ATMEL_SSC_RF | ATMEL_SSC_RD)
176 extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
178 /* LCD Controller */
179 struct atmel_lcdfb_info;
180 extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
182 /* AC97 */
183 extern void __init at91_add_device_ac97(struct ac97c_platform_data *data);
185 /* ISI */
186 extern void __init at91_add_device_isi(void);
188 /* Touchscreen Controller */
189 extern void __init at91_add_device_tsadcc(void);
191 /* CAN */
192 struct at91_can_data {
193 void (*transceiver_switch)(int on);
195 extern void __init at91_add_device_can(struct at91_can_data *data);
197 /* LEDs */
198 extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
199 extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
200 extern void __init at91_pwm_leds(struct gpio_led *leds, int nr);
202 /* FIXME: this needs a better location, but gets stuff building again */
203 extern int at91_suspend_entering_slow_clock(void);
205 #endif