OMAP3: GPIO: Enable debounce clock only when debounce is enabled v3.
[linux-ginger.git] / arch / arm / mach-lh7a40x / lcd-panel.h
bloba7f5027b2f789f207a6128f35d0e51120649a76e
1 /* lcd-panel.h
3 written by Marc Singer
4 18 Jul 2005
6 Copyright (C) 2005 Marc Singer
8 -----------
9 DESCRIPTION
10 -----------
12 Only one panel may be defined at a time.
14 The pixel clock is calculated to be no greater than the target.
16 Each timing value is accompanied by a specification comment.
18 UNITS/MIN/TYP/MAX
20 Most of the units will be in clocks.
22 USE_RGB555
24 Define this macro to configure the AMBA LCD controller to use an
25 RGB555 encoding for the pels instead of the normal RGB565.
27 LPD9520, LPD79524, LPD7A400, LPD7A404-10, LPD7A404-11
29 These boards are best approximated by 555 for all panels. Some
30 can use an extra low-order bit of blue in bit 16 of the color
31 value, but we don't have a way to communicate this non-linear
32 mapping to the kernel.
36 #if !defined (__LCD_PANEL_H__)
37 # define __LCD_PANEL_H__
39 #if defined (MACH_LPD79520)\
40 || defined (MACH_LPD79524)\
41 || defined (MACH_LPD7A400)\
42 || defined (MACH_LPD7A404)
43 # define USE_RGB555
44 #endif
46 struct clcd_panel_extra {
47 unsigned int hrmode;
48 unsigned int clsen;
49 unsigned int spsen;
50 unsigned int pcdel;
51 unsigned int revdel;
52 unsigned int lpdel;
53 unsigned int spldel;
54 unsigned int pc2del;
57 #define NS_TO_CLOCK(ns,c) ((((ns)*((c)/1000) + (1000000 - 1))/1000000))
58 #define CLOCK_TO_DIV(e,c) (((c) + (e) - 1)/(e))
60 #if defined CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
62 /* Logic Product Development LCD 3.5" QVGA HRTFT -10 */
63 /* Sharp PN LQ035Q7DB02 w/HRTFT controller chip */
65 #define PIX_CLOCK_TARGET (6800000)
66 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
67 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
69 static struct clcd_panel lcd_panel = {
70 .mode = {
71 .name = "3.5in QVGA (LQ035Q7DB02)",
72 .xres = 240,
73 .yres = 320,
74 .pixclock = PIX_CLOCK,
75 .left_margin = 16,
76 .right_margin = 21,
77 .upper_margin = 8, // line/8/8/8
78 .lower_margin = 5,
79 .hsync_len = 61,
80 .vsync_len = NS_TO_CLOCK (60, PIX_CLOCK),
81 .vmode = FB_VMODE_NONINTERLACED,
83 .width = -1,
84 .height = -1,
85 .tim2 = TIM2_IPC | (PIX_CLOCK_DIVIDER - 2),
86 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
87 .bpp = 16,
90 #define HAS_LCD_PANEL_EXTRA
92 static struct clcd_panel_extra lcd_panel_extra = {
93 .hrmode = 1,
94 .clsen = 1,
95 .spsen = 1,
96 .pcdel = 8,
97 .revdel = 7,
98 .lpdel = 13,
99 .spldel = 77,
100 .pc2del = 208,
103 #endif
105 #if defined CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02
107 /* Logic Product Development LCD 5.7" QVGA -10 */
108 /* Sharp PN LQ057Q3DC02 */
109 /* QVGA mode, V/Q=LOW */
111 /* From Sharp on 2006.1.3. I believe some of the values are incorrect
112 * based on the datasheet.
114 Timing0 TIMING1 TIMING2 CONTROL
115 0x140A0C4C 0x080504EF 0x013F380D 0x00000829
116 HBP= 20 VBP= 8 BCD= 0
117 HFP= 10 VFP= 5 CPL=319
118 HSW= 12 VSW= 1 IOE= 0
119 PPL= 19 LPP=239 IPC= 1
120 IHS= 1
121 IVS= 1
122 ACB= 0
123 CSEL= 0
124 PCD= 13
128 /* The full horizontal cycle (Th) is clock/360/400/450. */
129 /* The full vertical cycle (Tv) is line/251/262/280. */
131 #define PIX_CLOCK_TARGET (6300000) /* -/6.3/7 MHz */
132 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
133 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
135 static struct clcd_panel lcd_panel = {
136 .mode = {
137 .name = "5.7in QVGA (LQ057Q3DC02)",
138 .xres = 320,
139 .yres = 240,
140 .pixclock = PIX_CLOCK,
141 .left_margin = 11,
142 .right_margin = 400-11-320-2,
143 .upper_margin = 7, // line/7/7/7
144 .lower_margin = 262-7-240-2,
145 .hsync_len = 2, // clk/2/96/200
146 .vsync_len = 2, // line/2/-/34
147 .vmode = FB_VMODE_NONINTERLACED,
149 .width = -1,
150 .height = -1,
151 .tim2 = TIM2_IHS | TIM2_IVS
152 | (PIX_CLOCK_DIVIDER - 2),
153 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
154 .bpp = 16,
157 #endif
159 #if defined CONFIG_FB_ARMCLCD_SHARP_LQ64D343
161 /* Logic Product Development LCD 6.4" VGA -10 */
162 /* Sharp PN LQ64D343 */
164 /* The full horizontal cycle (Th) is clock/750/800/900. */
165 /* The full vertical cycle (Tv) is line/515/525/560. */
167 #define PIX_CLOCK_TARGET (28330000)
168 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
169 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
171 static struct clcd_panel lcd_panel = {
172 .mode = {
173 .name = "6.4in QVGA (LQ64D343)",
174 .xres = 640,
175 .yres = 480,
176 .pixclock = PIX_CLOCK,
177 .left_margin = 32,
178 .right_margin = 800-32-640-96,
179 .upper_margin = 32, // line/34/34/34
180 .lower_margin = 540-32-480-2,
181 .hsync_len = 96, // clk/2/96/200
182 .vsync_len = 2, // line/2/-/34
183 .vmode = FB_VMODE_NONINTERLACED,
185 .width = -1,
186 .height = -1,
187 .tim2 = TIM2_IHS | TIM2_IVS
188 | (PIX_CLOCK_DIVIDER - 2),
189 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
190 .bpp = 16,
193 #endif
195 #if defined CONFIG_FB_ARMCLCD_SHARP_LQ10D368
197 /* Logic Product Development LCD 10.4" VGA -10 */
198 /* Sharp PN LQ10D368 */
200 #define PIX_CLOCK_TARGET (28330000)
201 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
202 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
204 static struct clcd_panel lcd_panel = {
205 .mode = {
206 .name = "10.4in VGA (LQ10D368)",
207 .xres = 640,
208 .yres = 480,
209 .pixclock = PIX_CLOCK,
210 .left_margin = 21,
211 .right_margin = 15,
212 .upper_margin = 34,
213 .lower_margin = 5,
214 .hsync_len = 96,
215 .vsync_len = 16,
216 .vmode = FB_VMODE_NONINTERLACED,
218 .width = -1,
219 .height = -1,
220 .tim2 = TIM2_IHS | TIM2_IVS
221 | (PIX_CLOCK_DIVIDER - 2),
222 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
223 .bpp = 16,
226 #endif
228 #if defined CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41
230 /* Logic Product Development LCD 12.1" SVGA -10 */
231 /* Sharp PN LQ121S1DG41, was LQ121S1DG31 */
233 /* Note that with a 99993900 Hz HCLK, it is not possible to hit the
234 * target clock frequency range of 35MHz to 42MHz. */
236 /* If the target pixel clock is substantially lower than the panel
237 * spec, this is done to prevent the LCD display from glitching when
238 * the CPU is under load. A pixel clock higher than 25MHz
239 * (empirically determined) will compete with the CPU for bus cycles
240 * for the Ethernet chip. However, even a pixel clock of 10MHz
241 * competes with Compact Flash interface during some operations
242 * (fdisk, e2fsck). And, at that speed the display may have a visible
243 * flicker. */
245 /* The full horizontal cycle (Th) is clock/832/1056/1395. */
247 #define PIX_CLOCK_TARGET (20000000)
248 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
249 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
251 static struct clcd_panel lcd_panel = {
252 .mode = {
253 .name = "12.1in SVGA (LQ121S1DG41)",
254 .xres = 800,
255 .yres = 600,
256 .pixclock = PIX_CLOCK,
257 .left_margin = 89, // ns/5/-/(1/PIX_CLOCK)-10
258 .right_margin = 1056-800-89-128,
259 .upper_margin = 23, // line/23/23/23
260 .lower_margin = 44,
261 .hsync_len = 128, // clk/2/128/200
262 .vsync_len = 4, // line/2/4/6
263 .vmode = FB_VMODE_NONINTERLACED,
265 .width = -1,
266 .height = -1,
267 .tim2 = TIM2_IHS | TIM2_IVS
268 | (PIX_CLOCK_DIVIDER - 2),
269 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
270 .bpp = 16,
273 #endif
275 #if defined CONFIG_FB_ARMCLCD_HITACHI
277 /* Hitachi*/
278 /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
280 #define PIX_CLOCK_TARGET (49000000)
281 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
282 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
284 static struct clcd_panel lcd_panel = {
285 .mode = {
286 .name = "Hitachi 800x480",
287 .xres = 800,
288 .yres = 480,
289 .pixclock = PIX_CLOCK,
290 .left_margin = 88,
291 .right_margin = 40,
292 .upper_margin = 32,
293 .lower_margin = 11,
294 .hsync_len = 128,
295 .vsync_len = 2,
296 .vmode = FB_VMODE_NONINTERLACED,
298 .width = -1,
299 .height = -1,
300 .tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS
301 | (PIX_CLOCK_DIVIDER - 2),
302 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
303 .bpp = 16,
306 #endif
309 #if defined CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE
311 /* AU Optotronics A070VW01 7.0 Wide Screen color Display*/
312 /* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
314 #define PIX_CLOCK_TARGET (10000000)
315 #define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
316 #define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
318 static struct clcd_panel lcd_panel = {
319 .mode = {
320 .name = "7.0in Wide (A070VW01)",
321 .xres = 480,
322 .yres = 234,
323 .pixclock = PIX_CLOCK,
324 .left_margin = 30,
325 .right_margin = 25,
326 .upper_margin = 14,
327 .lower_margin = 12,
328 .hsync_len = 100,
329 .vsync_len = 1,
330 .vmode = FB_VMODE_NONINTERLACED,
332 .width = -1,
333 .height = -1,
334 .tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS
335 | (PIX_CLOCK_DIVIDER - 2),
336 .cntl = CNTL_LCDTFT | CNTL_WATERMARK,
337 .bpp = 16,
340 #endif
342 #undef NS_TO_CLOCK
343 #undef CLOCK_TO_DIV
345 #endif /* __LCD_PANEL_H__ */