| blob | b86a15f221ade983c075e18205f7187860c57f3e |
1 /****************************************************************************
2 * Driver for Solarflare Solarstorm network controllers and boards
3 * Copyright 2009-2011 Solarflare Communications Inc.
4 *
5 * This program is free software; you can redistribute it and/or modify it
6 * under the terms of the GNU General Public License version 2 as published
7 * by the Free Software Foundation, incorporated herein by reference.
8 */
11 #ifndef MCDI_PCOL_H
12 #define MCDI_PCOL_H
14 /* Values to be written into FMCR_CZ_RESET_STATE_REG to control boot. */
15 /* Power-on reset state */
16 #define MC_FW_STATE_POR (1)
17 /* If this is set in MC_RESET_STATE_REG then it should be
18 * possible to jump into IMEM without loading code from flash. */
19 #define MC_FW_WARM_BOOT_OK (2)
20 /* The MC main image has started to boot. */
21 #define MC_FW_STATE_BOOTING (4)
22 /* The Scheduler has started. */
23 #define MC_FW_STATE_SCHED (8)
25 /* Values to be written to the per-port status dword in shared
26 * memory on reboot and assert */
27 #define MC_STATUS_DWORD_REBOOT (0xb007b007)
28 #define MC_STATUS_DWORD_ASSERT (0xdeaddead)
30 /* The current version of the MCDI protocol.
31 *
32 * Note that the ROM burnt into the card only talks V0, so at the very
33 * least every driver must support version 0 and MCDI_PCOL_VERSION
34 */
35 #define MCDI_PCOL_VERSION 1
37 /**
38 * MCDI version 1
39 *
40 * Each MCDI request starts with an MCDI_HEADER, which is a 32byte
41 * structure, filled in by the client.
42 *
43 * 0 7 8 16 20 22 23 24 31
44 * | CODE | R | LEN | SEQ | Rsvd | E | R | XFLAGS |
45 * | | |
46 * | | \--- Response
47 * | \------- Error
48 * \------------------------------ Resync (always set)
49 *
50 * The client writes it's request into MC shared memory, and rings the
51 * doorbell. Each request is completed by either by the MC writting
52 * back into shared memory, or by writting out an event.
53 *
54 * All MCDI commands support completion by shared memory response. Each
55 * request may also contain additional data (accounted for by HEADER.LEN),
56 * and some response's may also contain additional data (again, accounted
57 * for by HEADER.LEN).
58 *
59 * Some MCDI commands support completion by event, in which any associated
60 * response data is included in the event.
61 *
62 * The protocol requires one response to be delivered for every request, a
63 * request should not be sent unless the response for the previous request
64 * has been received (either by polling shared memory, or by receiving
65 * an event).
66 */
68 /** Request/Response structure */
69 #define MCDI_HEADER_OFST 0
70 #define MCDI_HEADER_CODE_LBN 0
71 #define MCDI_HEADER_CODE_WIDTH 7
72 #define MCDI_HEADER_RESYNC_LBN 7
73 #define MCDI_HEADER_RESYNC_WIDTH 1
74 #define MCDI_HEADER_DATALEN_LBN 8
75 #define MCDI_HEADER_DATALEN_WIDTH 8
76 #define MCDI_HEADER_SEQ_LBN 16
77 #define MCDI_HEADER_RSVD_LBN 20
78 #define MCDI_HEADER_RSVD_WIDTH 2
79 #define MCDI_HEADER_SEQ_WIDTH 4
80 #define MCDI_HEADER_ERROR_LBN 22
81 #define MCDI_HEADER_ERROR_WIDTH 1
82 #define MCDI_HEADER_RESPONSE_LBN 23
83 #define MCDI_HEADER_RESPONSE_WIDTH 1
84 #define MCDI_HEADER_XFLAGS_LBN 24
85 #define MCDI_HEADER_XFLAGS_WIDTH 8
86 /* Request response using event */
87 #define MCDI_HEADER_XFLAGS_EVREQ 0x01
89 /* Maximum number of payload bytes */
90 #define MCDI_CTL_SDU_LEN_MAX 0xfc
92 /* The MC can generate events for two reasons:
93 * - To complete a shared memory request if XFLAGS_EVREQ was set
94 * - As a notification (link state, i2c event), controlled
95 * via MC_CMD_LOG_CTRL
96 *
97 * Both events share a common structure:
98 *
99 * 0 32 33 36 44 52 60
100 * | Data | Cont | Level | Src | Code | Rsvd |
101 * |
102 * \ There is another event pending in this notification
103 *
104 * If Code==CMDDONE, then the fields are further interpreted as:
105 *
106 * - LEVEL==INFO Command succeded
107 * - LEVEL==ERR Command failed
108 *
109 * 0 8 16 24 32
110 * | Seq | Datalen | Errno | Rsvd |
111 *
112 * These fields are taken directly out of the standard MCDI header, i.e.,
113 * LEVEL==ERR, Datalen == 0 => Reboot
114 *
115 * Events can be squirted out of the UART (using LOG_CTRL) without a
116 * MCDI header. An event can be distinguished from a MCDI response by
117 * examining the first byte which is 0xc0. This corresponds to the
118 * non-existent MCDI command MC_CMD_DEBUG_LOG.
119 *
120 * 0 7 8
121 * | command | Resync | = 0xc0
122 *
123 * Since the event is written in big-endian byte order, this works
124 * providing bits 56-63 of the event are 0xc0.
125 *
126 * 56 60 63
127 * | Rsvd | Code | = 0xc0
128 *
129 * Which means for convenience the event code is 0xc for all MC
130 * generated events.
131 */
132 #define FSE_AZ_EV_CODE_MCDI_EVRESPONSE 0xc
134 #define MCDI_EVENT_DATA_LBN 0
135 #define MCDI_EVENT_DATA_WIDTH 32
136 #define MCDI_EVENT_CONT_LBN 32
137 #define MCDI_EVENT_CONT_WIDTH 1
138 #define MCDI_EVENT_LEVEL_LBN 33
139 #define MCDI_EVENT_LEVEL_WIDTH 3
140 #define MCDI_EVENT_LEVEL_INFO (0)
141 #define MCDI_EVENT_LEVEL_WARN (1)
142 #define MCDI_EVENT_LEVEL_ERR (2)
143 #define MCDI_EVENT_LEVEL_FATAL (3)
144 #define MCDI_EVENT_SRC_LBN 36
145 #define MCDI_EVENT_SRC_WIDTH 8
146 #define MCDI_EVENT_CODE_LBN 44
147 #define MCDI_EVENT_CODE_WIDTH 8
148 #define MCDI_EVENT_CODE_BADSSERT (1)
149 #define MCDI_EVENT_CODE_PMNOTICE (2)
150 #define MCDI_EVENT_CODE_CMDDONE (3)
151 #define MCDI_EVENT_CMDDONE_SEQ_LBN 0
152 #define MCDI_EVENT_CMDDONE_SEQ_WIDTH 8
153 #define MCDI_EVENT_CMDDONE_DATALEN_LBN 8
154 #define MCDI_EVENT_CMDDONE_DATALEN_WIDTH 8
155 #define MCDI_EVENT_CMDDONE_ERRNO_LBN 16
156 #define MCDI_EVENT_CMDDONE_ERRNO_WIDTH 8
157 #define MCDI_EVENT_CODE_LINKCHANGE (4)
158 #define MCDI_EVENT_LINKCHANGE_LP_CAP_LBN 0
159 #define MCDI_EVENT_LINKCHANGE_LP_CAP_WIDTH 16
160 #define MCDI_EVENT_LINKCHANGE_SPEED_LBN 16
161 #define MCDI_EVENT_LINKCHANGE_SPEED_WIDTH 4
162 #define MCDI_EVENT_LINKCHANGE_SPEED_100M 1
163 #define MCDI_EVENT_LINKCHANGE_SPEED_1G 2
164 #define MCDI_EVENT_LINKCHANGE_SPEED_10G 3
165 #define MCDI_EVENT_LINKCHANGE_FCNTL_LBN 20
166 #define MCDI_EVENT_LINKCHANGE_FCNTL_WIDTH 4
167 #define MCDI_EVENT_LINKCHANGE_LINK_FLAGS_LBN 24
168 #define MCDI_EVENT_LINKCHANGE_LINK_FLAGS_WIDTH 8
169 #define MCDI_EVENT_CODE_SENSOREVT (5)
170 #define MCDI_EVENT_SENSOREVT_MONITOR_LBN 0
171 #define MCDI_EVENT_SENSOREVT_MONITOR_WIDTH 8
172 #define MCDI_EVENT_SENSOREVT_STATE_LBN 8
173 #define MCDI_EVENT_SENSOREVT_STATE_WIDTH 8
174 #define MCDI_EVENT_SENSOREVT_VALUE_LBN 16
175 #define MCDI_EVENT_SENSOREVT_VALUE_WIDTH 16
176 #define MCDI_EVENT_CODE_SCHEDERR (6)
177 #define MCDI_EVENT_CODE_REBOOT (7)
178 #define MCDI_EVENT_CODE_MAC_STATS_DMA (8)
179 #define MCDI_EVENT_MAC_STATS_DMA_GENERATION_LBN 0
180 #define MCDI_EVENT_MAC_STATS_DMA_GENERATION_WIDTH 32
182 /* Non-existent command target */
183 #define MC_CMD_ERR_ENOENT 2
184 /* assert() has killed the MC */
185 #define MC_CMD_ERR_EINTR 4
186 /* Caller does not hold required locks */
187 #define MC_CMD_ERR_EACCES 13
188 /* Resource is currently unavailable (e.g. lock contention) */
189 #define MC_CMD_ERR_EBUSY 16
190 /* Invalid argument to target */
191 #define MC_CMD_ERR_EINVAL 22
192 /* Non-recursive resource is already acquired */
193 #define MC_CMD_ERR_EDEADLK 35
194 /* Operation not implemented */
195 #define MC_CMD_ERR_ENOSYS 38
196 /* Operation timed out */
197 #define MC_CMD_ERR_ETIME 62
199 #define MC_CMD_ERR_CODE_OFST 0
202 /* MC_CMD_READ32: (debug, variadic out)
203 * Read multiple 32byte words from MC memory
204 */
205 #define MC_CMD_READ32 0x01
206 #define MC_CMD_READ32_IN_LEN 8
207 #define MC_CMD_READ32_IN_ADDR_OFST 0
208 #define MC_CMD_READ32_IN_NUMWORDS_OFST 4
209 #define MC_CMD_READ32_OUT_LEN(_numwords) \
210 (4 * (_numwords))
211 #define MC_CMD_READ32_OUT_BUFFER_OFST 0
213 /* MC_CMD_WRITE32: (debug, variadic in)
214 * Write multiple 32byte words to MC memory
215 */
216 #define MC_CMD_WRITE32 0x02
217 #define MC_CMD_WRITE32_IN_LEN(_numwords) (((_numwords) * 4) + 4)
218 #define MC_CMD_WRITE32_IN_ADDR_OFST 0
219 #define MC_CMD_WRITE32_IN_BUFFER_OFST 4
220 #define MC_CMD_WRITE32_OUT_LEN 0
222 /* MC_CMD_COPYCODE: (debug)
223 * Copy MC code between two locations and jump
224 */
225 #define MC_CMD_COPYCODE 0x03
226 #define MC_CMD_COPYCODE_IN_LEN 16
227 #define MC_CMD_COPYCODE_IN_SRC_ADDR_OFST 0
228 #define MC_CMD_COPYCODE_IN_DEST_ADDR_OFST 4
229 #define MC_CMD_COPYCODE_IN_NUMWORDS_OFST 8
230 #define MC_CMD_COPYCODE_IN_JUMP_OFST 12
231 /* Control should return to the caller rather than jumping */
232 #define MC_CMD_COPYCODE_JUMP_NONE 1
233 #define MC_CMD_COPYCODE_OUT_LEN 0
235 /* MC_CMD_SET_FUNC: (debug)
236 * Select function for function-specific commands.
237 */
238 #define MC_CMD_SET_FUNC 0x04
239 #define MC_CMD_SET_FUNC_IN_LEN 4
240 #define MC_CMD_SET_FUNC_IN_FUNC_OFST 0
241 #define MC_CMD_SET_FUNC_OUT_LEN 0
243 /* MC_CMD_GET_BOOT_STATUS:
244 * Get the instruction address from which the MC booted.
245 */
246 #define MC_CMD_GET_BOOT_STATUS 0x05
247 #define MC_CMD_GET_BOOT_STATUS_IN_LEN 0
248 #define MC_CMD_GET_BOOT_STATUS_OUT_LEN 8
249 #define MC_CMD_GET_BOOT_STATUS_OUT_BOOT_OFFSET_OFST 0
250 #define MC_CMD_GET_BOOT_STATUS_OUT_FLAGS_OFST 4
251 /* Reboot caused by watchdog */
252 #define MC_CMD_GET_BOOT_STATUS_FLAGS_WATCHDOG_LBN (0)
253 #define MC_CMD_GET_BOOT_STATUS_FLAGS_WATCHDOG_WIDTH (1)
254 /* MC booted from primary flash partition */
255 #define MC_CMD_GET_BOOT_STATUS_FLAGS_PRIMARY_LBN (1)
256 #define MC_CMD_GET_BOOT_STATUS_FLAGS_PRIMARY_WIDTH (1)
257 /* MC booted from backup flash partition */
258 #define MC_CMD_GET_BOOT_STATUS_FLAGS_BACKUP_LBN (2)
259 #define MC_CMD_GET_BOOT_STATUS_FLAGS_BACKUP_WIDTH (1)
261 /* MC_CMD_GET_ASSERTS: (debug, variadic out)
262 * Get (and optionally clear) the current assertion status.
263 *
264 * Only OUT.GLOBAL_FLAGS is guaranteed to exist in the completion
265 * payload. The other fields will only be present if
266 * OUT.GLOBAL_FLAGS != NO_FAILS
267 */
268 #define MC_CMD_GET_ASSERTS 0x06
269 #define MC_CMD_GET_ASSERTS_IN_LEN 4
270 #define MC_CMD_GET_ASSERTS_IN_CLEAR_OFST 0
271 #define MC_CMD_GET_ASSERTS_OUT_LEN 140
272 /* Assertion status flag */
273 #define MC_CMD_GET_ASSERTS_OUT_GLOBAL_FLAGS_OFST 0
274 /*! No assertions have failed. */
275 #define MC_CMD_GET_ASSERTS_FLAGS_NO_FAILS 1
276 /*! A system-level assertion has failed. */
277 #define MC_CMD_GET_ASSERTS_FLAGS_SYS_FAIL 2
278 /*! A thread-level assertion has failed. */
279 #define MC_CMD_GET_ASSERTS_FLAGS_THR_FAIL 3
280 /*! The system was reset by the watchdog. */
281 #define MC_CMD_GET_ASSERTS_FLAGS_WDOG_FIRED 4
282 /* Failing PC value */
283 #define MC_CMD_GET_ASSERTS_OUT_SAVED_PC_OFFS_OFST 4
284 /* Saved GP regs */
285 #define MC_CMD_GET_ASSERTS_OUT_GP_REGS_OFFS_OFST 8
286 #define MC_CMD_GET_ASSERTS_OUT_GP_REGS_LEN 124
287 /* Failing thread address */
288 #define MC_CMD_GET_ASSERTS_OUT_THREAD_OFFS_OFST 132
290 /* MC_CMD_LOG_CTRL:
291 * Determine the output stream for various events and messages
292 */
293 #define MC_CMD_LOG_CTRL 0x07
294 #define MC_CMD_LOG_CTRL_IN_LEN 8
295 #define MC_CMD_LOG_CTRL_IN_LOG_DEST_OFST 0
296 #define MC_CMD_LOG_CTRL_IN_LOG_DEST_UART (1)
297 #define MC_CMD_LOG_CTRL_IN_LOG_DEST_EVQ (2)
298 #define MC_CMD_LOG_CTRL_IN_LOG_DEST_EVQ_OFST 4
299 #define MC_CMD_LOG_CTRL_OUT_LEN 0
301 /* MC_CMD_GET_VERSION:
302 * Get version information about the MC firmware
303 */
304 #define MC_CMD_GET_VERSION 0x08
305 #define MC_CMD_GET_VERSION_IN_LEN 0
306 #define MC_CMD_GET_VERSION_V0_OUT_LEN 4
307 #define MC_CMD_GET_VERSION_V1_OUT_LEN 32
308 #define MC_CMD_GET_VERSION_OUT_FIRMWARE_OFST 0
309 /* Reserved version number to indicate "any" version. */
310 #define MC_CMD_GET_VERSION_OUT_FIRMWARE_ANY 0xffffffff
311 /* The version response of a boot ROM awaiting rescue */
312 #define MC_CMD_GET_VERSION_OUT_FIRMWARE_BOOTROM 0xb0070000
313 #define MC_CMD_GET_VERSION_V1_OUT_PCOL_OFST 4
314 /* 128bit mask of functions supported by the current firmware */
315 #define MC_CMD_GET_VERSION_V1_OUT_SUPPORTED_FUNCS_OFST 8
316 /* The command set exported by the boot ROM (MCDI v0) */
317 #define MC_CMD_GET_VERSION_V0_SUPPORTED_FUNCS { \
318 (1 << MC_CMD_READ32) | \
319 (1 << MC_CMD_WRITE32) | \
320 (1 << MC_CMD_COPYCODE) | \
321 (1 << MC_CMD_GET_VERSION), \
322 0, 0, 0 }
323 #define MC_CMD_GET_VERSION_OUT_VERSION_OFST 24
325 /* Vectors in the boot ROM */
326 /* Point to the copycode entry point. */
327 #define MC_BOOTROM_COPYCODE_VEC (0x7f4)
328 /* Points to the recovery mode entry point. */
329 #define MC_BOOTROM_NOFLASH_VEC (0x7f8)
331 /* Test execution limits */
332 #define MC_TESTEXEC_VARIANT_COUNT 16
333 #define MC_TESTEXEC_RESULT_COUNT 7
335 /* MC_CMD_SET_TESTVARS: (debug, variadic in)
336 * Write variant words for test.
337 *
338 * The user supplies a bitmap of the variants they wish to set.
339 * They must ensure that IN.LEN >= 4 + 4 * ffs(BITMAP)
340 */
341 #define MC_CMD_SET_TESTVARS 0x09
342 #define MC_CMD_SET_TESTVARS_IN_LEN(_numwords) \
343 (4 + 4*(_numwords))
344 #define MC_CMD_SET_TESTVARS_IN_ARGS_BITMAP_OFST 0
345 /* Up to MC_TESTEXEC_VARIANT_COUNT of 32byte words start here */
346 #define MC_CMD_SET_TESTVARS_IN_ARGS_BUFFER_OFST 4
347 #define MC_CMD_SET_TESTVARS_OUT_LEN 0
349 /* MC_CMD_GET_TESTRCS: (debug, variadic out)
350 * Return result words from test.
351 */
352 #define MC_CMD_GET_TESTRCS 0x0a
353 #define MC_CMD_GET_TESTRCS_IN_LEN 4
354 #define MC_CMD_GET_TESTRCS_IN_NUMWORDS_OFST 0
355 #define MC_CMD_GET_TESTRCS_OUT_LEN(_numwords) \
356 (4 * (_numwords))
357 #define MC_CMD_GET_TESTRCS_OUT_BUFFER_OFST 0
359 /* MC_CMD_RUN_TEST: (debug)
360 * Run the test exported by this firmware image
361 */
362 #define MC_CMD_RUN_TEST 0x0b
363 #define MC_CMD_RUN_TEST_IN_LEN 0
364 #define MC_CMD_RUN_TEST_OUT_LEN 0
366 /* MC_CMD_CSR_READ32: (debug, variadic out)
367 * Read 32bit words from the indirect memory map
368 */
369 #define MC_CMD_CSR_READ32 0x0c
370 #define MC_CMD_CSR_READ32_IN_LEN 12
371 #define MC_CMD_CSR_READ32_IN_ADDR_OFST 0
372 #define MC_CMD_CSR_READ32_IN_STEP_OFST 4
373 #define MC_CMD_CSR_READ32_IN_NUMWORDS_OFST 8
374 #define MC_CMD_CSR_READ32_OUT_LEN(_numwords) \
375 (((_numwords) * 4) + 4)
376 /* IN.NUMWORDS of 32bit words start here */
377 #define MC_CMD_CSR_READ32_OUT_BUFFER_OFST 0
378 #define MC_CMD_CSR_READ32_OUT_IREG_STATUS_OFST(_numwords) \
379 ((_numwords) * 4)
381 /* MC_CMD_CSR_WRITE32: (debug, variadic in)
382 * Write 32bit dwords to the indirect memory map
383 */
384 #define MC_CMD_CSR_WRITE32 0x0d
385 #define MC_CMD_CSR_WRITE32_IN_LEN(_numwords) \
386 (((_numwords) * 4) + 8)
387 #define MC_CMD_CSR_WRITE32_IN_ADDR_OFST 0
388 #define MC_CMD_CSR_WRITE32_IN_STEP_OFST 4
389 /* Multiple 32bit words of data to write start here */
390 #define MC_CMD_CSR_WRITE32_IN_BUFFER_OFST 8
391 #define MC_CMD_CSR_WRITE32_OUT_LEN 4
392 #define MC_CMD_CSR_WRITE32_OUT_STATUS_OFST 0
394 /* MC_CMD_JTAG_WORK: (debug, fpga only)
395 * Process JTAG work buffer for RBF acceleration.
396 *
397 * Host: bit count, (up to) 32 words of data to clock out to JTAG
398 * (bits 1,0=TMS,TDO for first bit; bits 3,2=TMS,TDO for second bit, etc.)
399 * MC: bit count, (up to) 32 words of data clocked in from JTAG
400 * (bit 0=TDI for first bit, bit 1=TDI for second bit, etc.; [31:16] unused)
401 */
402 #define MC_CMD_JTAG_WORK 0x0e
404 /* MC_CMD_STACKINFO: (debug, variadic out)
405 * Get stack information
406 *
407 * Host: nothing
408 * MC: (thread ptr, stack size, free space) for each thread in system
409 */
410 #define MC_CMD_STACKINFO 0x0f
412 /* MC_CMD_MDIO_READ:
413 * MDIO register read
414 */
415 #define MC_CMD_MDIO_READ 0x10
416 #define MC_CMD_MDIO_READ_IN_LEN 16
417 #define MC_CMD_MDIO_READ_IN_BUS_OFST 0
418 #define MC_CMD_MDIO_READ_IN_PRTAD_OFST 4
419 #define MC_CMD_MDIO_READ_IN_DEVAD_OFST 8
420 #define MC_CMD_MDIO_READ_IN_ADDR_OFST 12
421 #define MC_CMD_MDIO_READ_OUT_LEN 8
422 #define MC_CMD_MDIO_READ_OUT_VALUE_OFST 0
423 #define MC_CMD_MDIO_READ_OUT_STATUS_OFST 4
425 /* MC_CMD_MDIO_WRITE:
426 * MDIO register write
427 */
428 #define MC_CMD_MDIO_WRITE 0x11
429 #define MC_CMD_MDIO_WRITE_IN_LEN 20
430 #define MC_CMD_MDIO_WRITE_IN_BUS_OFST 0
431 #define MC_CMD_MDIO_WRITE_IN_PRTAD_OFST 4
432 #define MC_CMD_MDIO_WRITE_IN_DEVAD_OFST 8
433 #define MC_CMD_MDIO_WRITE_IN_ADDR_OFST 12
434 #define MC_CMD_MDIO_WRITE_IN_VALUE_OFST 16
435 #define MC_CMD_MDIO_WRITE_OUT_LEN 4
436 #define MC_CMD_MDIO_WRITE_OUT_STATUS_OFST 0
438 /* By default all the MCDI MDIO operations perform clause45 mode.
439 * If you want to use clause22 then set DEVAD = MC_CMD_MDIO_CLAUSE22.
440 */
441 #define MC_CMD_MDIO_CLAUSE22 32
443 /* There are two MDIO buses: one for the internal PHY, and one for external
444 * devices.
445 */
446 #define MC_CMD_MDIO_BUS_INTERNAL 0
447 #define MC_CMD_MDIO_BUS_EXTERNAL 1
449 /* The MDIO commands return the raw status bits from the MDIO block. A "good"
450 * transaction should have the DONE bit set and all other bits clear.
451 */
452 #define MC_CMD_MDIO_STATUS_GOOD 0x08
455 /* MC_CMD_DBI_WRITE: (debug)
456 * Write DBI register(s)
457 *
458 * Host: address, byte-enables (and VF selection, and cs2 flag),
459 * value [,address ...]
460 * MC: nothing
461 */
462 #define MC_CMD_DBI_WRITE 0x12
463 #define MC_CMD_DBI_WRITE_IN_LEN(_numwords) \
464 (12 * (_numwords))
465 #define MC_CMD_DBI_WRITE_IN_ADDRESS_OFST(_word) \
466 (((_word) * 12) + 0)
467 #define MC_CMD_DBI_WRITE_IN_BYTE_MASK_OFST(_word) \
468 (((_word) * 12) + 4)
469 #define MC_CMD_DBI_WRITE_IN_VALUE_OFST(_word) \
470 (((_word) * 12) + 8)
471 #define MC_CMD_DBI_WRITE_OUT_LEN 0
473 /* MC_CMD_DBI_READ: (debug)
474 * Read DBI register(s)
475 *
476 * Host: address, [,address ...]
477 * MC: value [,value ...]
478 * (note: this does not support reading from VFs, but is retained for backwards
479 * compatibility; see MC_CMD_DBI_READX below)
480 */
481 #define MC_CMD_DBI_READ 0x13
482 #define MC_CMD_DBI_READ_IN_LEN(_numwords) \
483 (4 * (_numwords))
484 #define MC_CMD_DBI_READ_OUT_LEN(_numwords) \
485 (4 * (_numwords))
487 /* MC_CMD_PORT_READ32: (debug)
488 * Read a 32-bit register from the indirect port register map.
489 *
490 * The port to access is implied by the Shared memory channel used.
491 */
492 #define MC_CMD_PORT_READ32 0x14
493 #define MC_CMD_PORT_READ32_IN_LEN 4
494 #define MC_CMD_PORT_READ32_IN_ADDR_OFST 0
495 #define MC_CMD_PORT_READ32_OUT_LEN 8
496 #define MC_CMD_PORT_READ32_OUT_VALUE_OFST 0
497 #define MC_CMD_PORT_READ32_OUT_STATUS_OFST 4
499 /* MC_CMD_PORT_WRITE32: (debug)
500 * Write a 32-bit register to the indirect port register map.
501 *
502 * The port to access is implied by the Shared memory channel used.
503 */
504 #define MC_CMD_PORT_WRITE32 0x15
505 #define MC_CMD_PORT_WRITE32_IN_LEN 8
506 #define MC_CMD_PORT_WRITE32_IN_ADDR_OFST 0
507 #define MC_CMD_PORT_WRITE32_IN_VALUE_OFST 4
508 #define MC_CMD_PORT_WRITE32_OUT_LEN 4
509 #define MC_CMD_PORT_WRITE32_OUT_STATUS_OFST 0
511 /* MC_CMD_PORT_READ128: (debug)
512 * Read a 128-bit register from indirect port register map
513 *
514 * The port to access is implied by the Shared memory channel used.
515 */
516 #define MC_CMD_PORT_READ128 0x16
517 #define MC_CMD_PORT_READ128_IN_LEN 4
518 #define MC_CMD_PORT_READ128_IN_ADDR_OFST 0
519 #define MC_CMD_PORT_READ128_OUT_LEN 20
520 #define MC_CMD_PORT_READ128_OUT_VALUE_OFST 0
521 #define MC_CMD_PORT_READ128_OUT_STATUS_OFST 16
523 /* MC_CMD_PORT_WRITE128: (debug)
524 * Write a 128-bit register to indirect port register map.
525 *
526 * The port to access is implied by the Shared memory channel used.
527 */
528 #define MC_CMD_PORT_WRITE128 0x17
529 #define MC_CMD_PORT_WRITE128_IN_LEN 20
530 #define MC_CMD_PORT_WRITE128_IN_ADDR_OFST 0
531 #define MC_CMD_PORT_WRITE128_IN_VALUE_OFST 4
532 #define MC_CMD_PORT_WRITE128_OUT_LEN 4
533 #define MC_CMD_PORT_WRITE128_OUT_STATUS_OFST 0
535 /* MC_CMD_GET_BOARD_CFG:
536 * Returns the MC firmware configuration structure
537 *
538 * The FW_SUBTYPE_LIST contains a 16-bit value for each of the 12 types of
539 * NVRAM area. The values are defined in the firmware/mc/platform/<xxx>.c file
540 * for a specific board type, but otherwise have no meaning to the MC; they
541 * are used by the driver to manage selection of appropriate firmware updates.
542 */
543 #define MC_CMD_GET_BOARD_CFG 0x18
544 #define MC_CMD_GET_BOARD_CFG_IN_LEN 0
545 #define MC_CMD_GET_BOARD_CFG_OUT_LEN 96
546 #define MC_CMD_GET_BOARD_CFG_OUT_BOARD_TYPE_OFST 0
547 #define MC_CMD_GET_BOARD_CFG_OUT_BOARD_NAME_OFST 4
548 #define MC_CMD_GET_BOARD_CFG_OUT_BOARD_NAME_LEN 32
549 #define MC_CMD_GET_BOARD_CFG_OUT_CAPABILITIES_PORT0_OFST 36
550 #define MC_CMD_GET_BOARD_CFG_OUT_CAPABILITIES_PORT1_OFST 40
551 #define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT0_OFST 44
552 #define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT0_LEN 6
553 #define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT1_OFST 50
554 #define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT1_LEN 6
555 #define MC_CMD_GET_BOARD_CFG_OUT_MAC_COUNT_PORT0_OFST 56
556 #define MC_CMD_GET_BOARD_CFG_OUT_MAC_COUNT_PORT1_OFST 60
557 #define MC_CMD_GET_BOARD_CFG_OUT_MAC_STRIDE_PORT0_OFST 64
558 #define MC_CMD_GET_BOARD_CFG_OUT_MAC_STRIDE_PORT1_OFST 68
559 #define MC_CMD_GET_BOARD_CFG_OUT_FW_SUBTYPE_LIST_OFST 72
560 #define MC_CMD_GET_BOARD_CFG_OUT_FW_SUBTYPE_LIST_LEN 24
562 /* MC_CMD_DBI_READX: (debug)
563 * Read DBI register(s) -- extended functionality
564 *
565 * Host: vf selection, address, [,vf selection ...]
566 * MC: value [,value ...]
567 */
568 #define MC_CMD_DBI_READX 0x19
569 #define MC_CMD_DBI_READX_IN_LEN(_numwords) \
570 (8*(_numwords))
571 #define MC_CMD_DBI_READX_OUT_LEN(_numwords) \
572 (4*(_numwords))
574 /* MC_CMD_SET_RAND_SEED:
575 * Set the 16byte seed for the MC psuedo-random generator
576 */
577 #define MC_CMD_SET_RAND_SEED 0x1a
578 #define MC_CMD_SET_RAND_SEED_IN_LEN 16
579 #define MC_CMD_SET_RAND_SEED_IN_SEED_OFST 0
580 #define MC_CMD_SET_RAND_SEED_OUT_LEN 0
582 /* MC_CMD_LTSSM_HIST: (debug)
583 * Retrieve the history of the LTSSM, if the build supports it.
584 *
585 * Host: nothing
586 * MC: variable number of LTSSM values, as bytes
587 * The history is read-to-clear.
588 */
589 #define MC_CMD_LTSSM_HIST 0x1b
591 /* MC_CMD_DRV_ATTACH:
592 * Inform MCPU that this port is managed on the host (i.e. driver active)
593 */
594 #define MC_CMD_DRV_ATTACH 0x1c
595 #define MC_CMD_DRV_ATTACH_IN_LEN 8
596 #define MC_CMD_DRV_ATTACH_IN_NEW_STATE_OFST 0
597 #define MC_CMD_DRV_ATTACH_IN_UPDATE_OFST 4
598 #define MC_CMD_DRV_ATTACH_OUT_LEN 4
599 #define MC_CMD_DRV_ATTACH_OUT_OLD_STATE_OFST 0
601 /* MC_CMD_NCSI_PROD: (debug)
602 * Trigger an NC-SI event (and possibly an AEN in response)
603 */
604 #define MC_CMD_NCSI_PROD 0x1d
605 #define MC_CMD_NCSI_PROD_IN_LEN 4
606 #define MC_CMD_NCSI_PROD_IN_EVENTS_OFST 0
607 #define MC_CMD_NCSI_PROD_LINKCHANGE_LBN 0
608 #define MC_CMD_NCSI_PROD_LINKCHANGE_WIDTH 1
609 #define MC_CMD_NCSI_PROD_RESET_LBN 1
610 #define MC_CMD_NCSI_PROD_RESET_WIDTH 1
611 #define MC_CMD_NCSI_PROD_DRVATTACH_LBN 2
612 #define MC_CMD_NCSI_PROD_DRVATTACH_WIDTH 1
613 #define MC_CMD_NCSI_PROD_OUT_LEN 0
615 /* Enumeration */
616 #define MC_CMD_NCSI_PROD_LINKCHANGE 0
617 #define MC_CMD_NCSI_PROD_RESET 1
618 #define MC_CMD_NCSI_PROD_DRVATTACH 2
620 /* MC_CMD_DEVEL: (debug)
621 * Reserved for development
622 */
623 #define MC_CMD_DEVEL 0x1e
625 /* MC_CMD_SHMUART: (debug)
626 * Route UART output to circular buffer in shared memory instead.
627 */
628 #define MC_CMD_SHMUART 0x1f
629 #define MC_CMD_SHMUART_IN_FLAG_OFST 0
630 #define MC_CMD_SHMUART_IN_LEN 4
631 #define MC_CMD_SHMUART_OUT_LEN 0
633 /* MC_CMD_PORT_RESET:
634 * Generic per-port reset. There is no equivalent for per-board reset.
635 *
636 * Locks required: None
637 * Return code: 0, ETIME
638 */
639 #define MC_CMD_PORT_RESET 0x20
640 #define MC_CMD_PORT_RESET_IN_LEN 0
641 #define MC_CMD_PORT_RESET_OUT_LEN 0
643 /* MC_CMD_RESOURCE_LOCK:
644 * Generic resource lock/unlock interface.
645 *
646 * Locks required: None
647 * Return code: 0,
648 * EBUSY (if trylock is contended by other port),
649 * EDEADLK (if trylock is already acquired by this port)
650 * EINVAL (if unlock doesn't own the lock)
651 */
652 #define MC_CMD_RESOURCE_LOCK 0x21
653 #define MC_CMD_RESOURCE_LOCK_IN_LEN 8
654 #define MC_CMD_RESOURCE_LOCK_IN_ACTION_OFST 0
655 #define MC_CMD_RESOURCE_LOCK_ACTION_TRYLOCK 1
656 #define MC_CMD_RESOURCE_LOCK_ACTION_UNLOCK 0
657 #define MC_CMD_RESOURCE_LOCK_IN_RESOURCE_OFST 4
658 #define MC_CMD_RESOURCE_LOCK_I2C 2
659 #define MC_CMD_RESOURCE_LOCK_PHY 3
660 #define MC_CMD_RESOURCE_LOCK_OUT_LEN 0
662 /* MC_CMD_SPI_COMMAND: (variadic in, variadic out)
663 * Read/Write to/from the SPI device.
664 *
665 * Locks required: SPI_LOCK
666 * Return code: 0, ETIME, EINVAL, EACCES (if SPI_LOCK is not held)
667 */
668 #define MC_CMD_SPI_COMMAND 0x22
669 #define MC_CMD_SPI_COMMAND_IN_LEN(_write_bytes) (12 + (_write_bytes))
670 #define MC_CMD_SPI_COMMAND_IN_ARGS_OFST 0
671 #define MC_CMD_SPI_COMMAND_IN_ARGS_ADDRESS_OFST 0
672 #define MC_CMD_SPI_COMMAND_IN_ARGS_READ_BYTES_OFST 4
673 #define MC_CMD_SPI_COMMAND_IN_ARGS_CHIP_SELECT_OFST 8
674 /* Data to write here */
675 #define MC_CMD_SPI_COMMAND_IN_WRITE_BUFFER_OFST 12
676 #define MC_CMD_SPI_COMMAND_OUT_LEN(_read_bytes) (_read_bytes)
677 /* Data read here */
678 #define MC_CMD_SPI_COMMAND_OUT_READ_BUFFER_OFST 0
680 /* MC_CMD_I2C_READ_WRITE: (variadic in, variadic out)
681 * Read/Write to/from the I2C bus.
682 *
683 * Locks required: I2C_LOCK
684 * Return code: 0, ETIME, EINVAL, EACCES (if I2C_LOCK is not held)
685 */
686 #define MC_CMD_I2C_RW 0x23
687 #define MC_CMD_I2C_RW_IN_LEN(_write_bytes) (8 + (_write_bytes))
688 #define MC_CMD_I2C_RW_IN_ARGS_OFST 0
689 #define MC_CMD_I2C_RW_IN_ARGS_ADDR_OFST 0
690 #define MC_CMD_I2C_RW_IN_ARGS_READ_BYTES_OFST 4
691 /* Data to write here */
692 #define MC_CMD_I2C_RW_IN_WRITE_BUFFER_OFSET 8
693 #define MC_CMD_I2C_RW_OUT_LEN(_read_bytes) (_read_bytes)
694 /* Data read here */
695 #define MC_CMD_I2C_RW_OUT_READ_BUFFER_OFST 0
697 /* Generic phy capability bitmask */
698 #define MC_CMD_PHY_CAP_10HDX_LBN 1
699 #define MC_CMD_PHY_CAP_10HDX_WIDTH 1
700 #define MC_CMD_PHY_CAP_10FDX_LBN 2
701 #define MC_CMD_PHY_CAP_10FDX_WIDTH 1
702 #define MC_CMD_PHY_CAP_100HDX_LBN 3
703 #define MC_CMD_PHY_CAP_100HDX_WIDTH 1
704 #define MC_CMD_PHY_CAP_100FDX_LBN 4
705 #define MC_CMD_PHY_CAP_100FDX_WIDTH 1
706 #define MC_CMD_PHY_CAP_1000HDX_LBN 5
707 #define MC_CMD_PHY_CAP_1000HDX_WIDTH 1
708 #define MC_CMD_PHY_CAP_1000FDX_LBN 6
709 #define MC_CMD_PHY_CAP_1000FDX_WIDTH 1
710 #define MC_CMD_PHY_CAP_10000FDX_LBN 7
711 #define MC_CMD_PHY_CAP_10000FDX_WIDTH 1
712 #define MC_CMD_PHY_CAP_PAUSE_LBN 8
713 #define MC_CMD_PHY_CAP_PAUSE_WIDTH 1
714 #define MC_CMD_PHY_CAP_ASYM_LBN 9
715 #define MC_CMD_PHY_CAP_ASYM_WIDTH 1
716 #define MC_CMD_PHY_CAP_AN_LBN 10
717 #define MC_CMD_PHY_CAP_AN_WIDTH 1
719 /* Generic loopback enumeration */
720 #define MC_CMD_LOOPBACK_NONE 0
721 #define MC_CMD_LOOPBACK_DATA 1
722 #define MC_CMD_LOOPBACK_GMAC 2
723 #define MC_CMD_LOOPBACK_XGMII 3
724 #define MC_CMD_LOOPBACK_XGXS 4
725 #define MC_CMD_LOOPBACK_XAUI 5
726 #define MC_CMD_LOOPBACK_GMII 6
727 #define MC_CMD_LOOPBACK_SGMII 7
728 #define MC_CMD_LOOPBACK_XGBR 8
729 #define MC_CMD_LOOPBACK_XFI 9
730 #define MC_CMD_LOOPBACK_XAUI_FAR 10
731 #define MC_CMD_LOOPBACK_GMII_FAR 11
732 #define MC_CMD_LOOPBACK_SGMII_FAR 12
733 #define MC_CMD_LOOPBACK_XFI_FAR 13
734 #define MC_CMD_LOOPBACK_GPHY 14
735 #define MC_CMD_LOOPBACK_PHYXS 15
736 #define MC_CMD_LOOPBACK_PCS 16
737 #define MC_CMD_LOOPBACK_PMAPMD 17
738 #define MC_CMD_LOOPBACK_XPORT 18
739 #define MC_CMD_LOOPBACK_XGMII_WS 19
740 #define MC_CMD_LOOPBACK_XAUI_WS 20
741 #define MC_CMD_LOOPBACK_XAUI_WS_FAR 21
742 #define MC_CMD_LOOPBACK_XAUI_WS_NEAR 22
743 #define MC_CMD_LOOPBACK_GMII_WS 23
744 #define MC_CMD_LOOPBACK_XFI_WS 24
745 #define MC_CMD_LOOPBACK_XFI_WS_FAR 25
746 #define MC_CMD_LOOPBACK_PHYXS_WS 26
748 /* Generic PHY statistics enumeration */
749 #define MC_CMD_OUI 0
750 #define MC_CMD_PMA_PMD_LINK_UP 1
751 #define MC_CMD_PMA_PMD_RX_FAULT 2
752 #define MC_CMD_PMA_PMD_TX_FAULT 3
753 #define MC_CMD_PMA_PMD_SIGNAL 4
754 #define MC_CMD_PMA_PMD_SNR_A 5
755 #define MC_CMD_PMA_PMD_SNR_B 6
756 #define MC_CMD_PMA_PMD_SNR_C 7
757 #define MC_CMD_PMA_PMD_SNR_D 8
758 #define MC_CMD_PCS_LINK_UP 9
759 #define MC_CMD_PCS_RX_FAULT 10
760 #define MC_CMD_PCS_TX_FAULT 11
761 #define MC_CMD_PCS_BER 12
762 #define MC_CMD_PCS_BLOCK_ERRORS 13
763 #define MC_CMD_PHYXS_LINK_UP 14
764 #define MC_CMD_PHYXS_RX_FAULT 15
765 #define MC_CMD_PHYXS_TX_FAULT 16
766 #define MC_CMD_PHYXS_ALIGN 17
767 #define MC_CMD_PHYXS_SYNC 18
768 #define MC_CMD_AN_LINK_UP 19
769 #define MC_CMD_AN_COMPLETE 20
770 #define MC_CMD_AN_10GBT_STATUS 21
771 #define MC_CMD_CL22_LINK_UP 22
772 #define MC_CMD_PHY_NSTATS 23
774 /* MC_CMD_GET_PHY_CFG:
775 * Report PHY configuration. This guarantees to succeed even if the PHY is in
776 * a "zombie" state.
777 *
778 * Locks required: None
779 * Return code: 0
780 */
781 #define MC_CMD_GET_PHY_CFG 0x24
783 #define MC_CMD_GET_PHY_CFG_IN_LEN 0
784 #define MC_CMD_GET_PHY_CFG_OUT_LEN 72
786 #define MC_CMD_GET_PHY_CFG_OUT_FLAGS_OFST 0
787 #define MC_CMD_GET_PHY_CFG_PRESENT_LBN 0
788 #define MC_CMD_GET_PHY_CFG_PRESENT_WIDTH 1
789 #define MC_CMD_GET_PHY_CFG_BIST_CABLE_SHORT_LBN 1
790 #define MC_CMD_GET_PHY_CFG_BIST_CABLE_SHORT_WIDTH 1
791 #define MC_CMD_GET_PHY_CFG_BIST_CABLE_LONG_LBN 2
792 #define MC_CMD_GET_PHY_CFG_BIST_CABLE_LONG_WIDTH 1
793 #define MC_CMD_GET_PHY_CFG_LOWPOWER_LBN 3
794 #define MC_CMD_GET_PHY_CFG_LOWPOWER_WIDTH 1
795 #define MC_CMD_GET_PHY_CFG_POWEROFF_LBN 4
796 #define MC_CMD_GET_PHY_CFG_POWEROFF_WIDTH 1
797 #define MC_CMD_GET_PHY_CFG_TXDIS_LBN 5
798 #define MC_CMD_GET_PHY_CFG_TXDIS_WIDTH 1
799 #define MC_CMD_GET_PHY_CFG_BIST_LBN 6
800 #define MC_CMD_GET_PHY_CFG_BIST_WIDTH 1
801 #define MC_CMD_GET_PHY_CFG_OUT_TYPE_OFST 4
802 /* Bitmask of supported capabilities */
803 #define MC_CMD_GET_PHY_CFG_OUT_SUPPORTED_CAP_OFST 8
804 #define MC_CMD_GET_PHY_CFG_OUT_CHANNEL_OFST 12
805 #define MC_CMD_GET_PHY_CFG_OUT_PRT_OFST 16
806 /* PHY statistics bitmap */
807 #define MC_CMD_GET_PHY_CFG_OUT_STATS_MASK_OFST 20
808 /* PHY type/name string */
809 #define MC_CMD_GET_PHY_CFG_OUT_NAME_OFST 24
810 #define MC_CMD_GET_PHY_CFG_OUT_NAME_LEN 20
811 #define MC_CMD_GET_PHY_CFG_OUT_MEDIA_TYPE_OFST 44
812 #define MC_CMD_MEDIA_XAUI 1
813 #define MC_CMD_MEDIA_CX4 2
814 #define MC_CMD_MEDIA_KX4 3
815 #define MC_CMD_MEDIA_XFP 4
816 #define MC_CMD_MEDIA_SFP_PLUS 5
817 #define MC_CMD_MEDIA_BASE_T 6
818 /* MDIO "MMDS" supported */
819 #define MC_CMD_GET_PHY_CFG_OUT_MMD_MASK_OFST 48
820 /* Native clause 22 */
821 #define MC_CMD_MMD_CLAUSE22 0
822 #define MC_CMD_MMD_CLAUSE45_PMAPMD 1
823 #define MC_CMD_MMD_CLAUSE45_WIS 2
824 #define MC_CMD_MMD_CLAUSE45_PCS 3
825 #define MC_CMD_MMD_CLAUSE45_PHYXS 4
826 #define MC_CMD_MMD_CLAUSE45_DTEXS 5
827 #define MC_CMD_MMD_CLAUSE45_TC 6
828 #define MC_CMD_MMD_CLAUSE45_AN 7
829 /* Clause22 proxied over clause45 by PHY */
830 #define MC_CMD_MMD_CLAUSE45_C22EXT 29
831 #define MC_CMD_MMD_CLAUSE45_VEND1 30
832 #define MC_CMD_MMD_CLAUSE45_VEND2 31
833 /* PHY stepping version */
834 #define MC_CMD_GET_PHY_CFG_OUT_REVISION_OFST 52
835 #define MC_CMD_GET_PHY_CFG_OUT_REVISION_LEN 20
837 /* MC_CMD_START_BIST:
838 * Start a BIST test on the PHY.
839 *
840 * Locks required: PHY_LOCK if doing a PHY BIST
841 * Return code: 0, EINVAL, EACCES (if PHY_LOCK is not held)
842 */
843 #define MC_CMD_START_BIST 0x25
844 #define MC_CMD_START_BIST_IN_LEN 4
845 #define MC_CMD_START_BIST_IN_TYPE_OFST 0
846 #define MC_CMD_START_BIST_OUT_LEN 0
848 /* Run the PHY's short cable BIST */
849 #define MC_CMD_PHY_BIST_CABLE_SHORT 1
850 /* Run the PHY's long cable BIST */
851 #define MC_CMD_PHY_BIST_CABLE_LONG 2
852 /* Run BIST on the currently selected BPX Serdes (XAUI or XFI) */
853 #define MC_CMD_BPX_SERDES_BIST 3
854 /* Run the MC loopback tests */
855 #define MC_CMD_MC_LOOPBACK_BIST 4
856 /* Run the PHY's standard BIST */
857 #define MC_CMD_PHY_BIST 5
859 /* MC_CMD_POLL_PHY_BIST: (variadic output)
860 * Poll for BIST completion
861 *
862 * Returns a single status code, and optionally some PHY specific
863 * bist output. The driver should only consume the BIST output
864 * after validating OUTLEN and PHY_CFG.PHY_TYPE.
865 *
866 * If a driver can't successfully parse the BIST output, it should
867 * still respect the pass/Fail in OUT.RESULT
868 *
869 * Locks required: PHY_LOCK if doing a PHY BIST
870 * Return code: 0, EACCES (if PHY_LOCK is not held)
871 */
872 #define MC_CMD_POLL_BIST 0x26
873 #define MC_CMD_POLL_BIST_IN_LEN 0
874 #define MC_CMD_POLL_BIST_OUT_LEN UNKNOWN
875 #define MC_CMD_POLL_BIST_OUT_SFT9001_LEN 36
876 #define MC_CMD_POLL_BIST_OUT_MRSFP_LEN 8
877 #define MC_CMD_POLL_BIST_OUT_RESULT_OFST 0
878 #define MC_CMD_POLL_BIST_RUNNING 1
879 #define MC_CMD_POLL_BIST_PASSED 2
880 #define MC_CMD_POLL_BIST_FAILED 3
881 #define MC_CMD_POLL_BIST_TIMEOUT 4
882 /* Generic: */
883 #define MC_CMD_POLL_BIST_OUT_PRIVATE_OFST 4
884 /* SFT9001-specific: */
885 #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_A_OFST 4
886 #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_B_OFST 8
887 #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_C_OFST 12
888 #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_D_OFST 16
889 #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_A_OFST 20
890 #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_B_OFST 24
891 #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_C_OFST 28
892 #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_D_OFST 32
893 #define MC_CMD_POLL_BIST_SFT9001_PAIR_OK 1
894 #define MC_CMD_POLL_BIST_SFT9001_PAIR_OPEN 2
895 #define MC_CMD_POLL_BIST_SFT9001_INTRA_PAIR_SHORT 3
896 #define MC_CMD_POLL_BIST_SFT9001_INTER_PAIR_SHORT 4
897 #define MC_CMD_POLL_BIST_SFT9001_PAIR_BUSY 9
898 /* mrsfp "PHY" driver: */
899 #define MC_CMD_POLL_BIST_OUT_MRSFP_TEST_OFST 4
900 #define MC_CMD_POLL_BIST_MRSFP_TEST_COMPLETE 0
901 #define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_OFF_I2C_WRITE 1
902 #define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_OFF_I2C_NO_ACCESS_IO_EXP 2
903 #define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_OFF_I2C_NO_ACCESS_MODULE 3
904 #define MC_CMD_POLL_BIST_MRSFP_TEST_IO_EXP_I2C_CONFIGURE 4
905 #define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_I2C_NO_CROSSTALK 5
906 #define MC_CMD_POLL_BIST_MRSFP_TEST_MODULE_PRESENCE 6
907 #define MC_CMD_POLL_BIST_MRSFP_TEST_MODULE_ID_I2C_ACCESS 7
908 #define MC_CMD_POLL_BIST_MRSFP_TEST_MODULE_ID_SANE_VALUE 8
910 /* MC_CMD_PHY_SPI: (variadic in, variadic out)
911 * Read/Write/Erase the PHY SPI device
912 *
913 * Locks required: PHY_LOCK
914 * Return code: 0, ETIME, EINVAL, EACCES (if PHY_LOCK is not held)
915 */
916 #define MC_CMD_PHY_SPI 0x27
917 #define MC_CMD_PHY_SPI_IN_LEN(_write_bytes) (12 + (_write_bytes))
918 #define MC_CMD_PHY_SPI_IN_ARGS_OFST 0
919 #define MC_CMD_PHY_SPI_IN_ARGS_ADDR_OFST 0
920 #define MC_CMD_PHY_SPI_IN_ARGS_READ_BYTES_OFST 4
921 #define MC_CMD_PHY_SPI_IN_ARGS_ERASE_ALL_OFST 8
922 /* Data to write here */
923 #define MC_CMD_PHY_SPI_IN_WRITE_BUFFER_OFSET 12
924 #define MC_CMD_PHY_SPI_OUT_LEN(_read_bytes) (_read_bytes)
925 /* Data read here */
926 #define MC_CMD_PHY_SPI_OUT_READ_BUFFER_OFST 0
929 /* MC_CMD_GET_LOOPBACK_MODES:
930 * Returns a bitmask of loopback modes evailable at each speed.
931 *
932 * Locks required: None
933 * Return code: 0
934 */
935 #define MC_CMD_GET_LOOPBACK_MODES 0x28
936 #define MC_CMD_GET_LOOPBACK_MODES_IN_LEN 0
937 #define MC_CMD_GET_LOOPBACK_MODES_OUT_LEN 32
938 #define MC_CMD_GET_LOOPBACK_MODES_100M_OFST 0
939 #define MC_CMD_GET_LOOPBACK_MODES_1G_OFST 8
940 #define MC_CMD_GET_LOOPBACK_MODES_10G_OFST 16
941 #define MC_CMD_GET_LOOPBACK_MODES_SUGGESTED_OFST 24
943 /* Flow control enumeration */
944 #define MC_CMD_FCNTL_OFF 0
945 #define MC_CMD_FCNTL_RESPOND 1
946 #define MC_CMD_FCNTL_BIDIR 2
947 /* Auto - Use what the link has autonegotiated
948 * - The driver should modify the advertised capabilities via SET_LINK.CAP
949 * to control the negotiated flow control mode.
950 * - Can only be set if the PHY supports PAUSE+ASYM capabilities
951 * - Never returned by GET_LINK as the value programmed into the MAC
952 */
953 #define MC_CMD_FCNTL_AUTO 3
955 /* Generic mac fault bitmask */
956 #define MC_CMD_MAC_FAULT_XGMII_LOCAL_LBN 0
957 #define MC_CMD_MAC_FAULT_XGMII_LOCAL_WIDTH 1
958 #define MC_CMD_MAC_FAULT_XGMII_REMOTE_LBN 1
959 #define MC_CMD_MAC_FAULT_XGMII_REMOTE_WIDTH 1
960 #define MC_CMD_MAC_FAULT_SGMII_REMOTE_LBN 2
961 #define MC_CMD_MAC_FAULT_SGMII_REMOTE_WIDTH 1
963 /* MC_CMD_GET_LINK:
964 * Read the unified MAC/PHY link state
965 *
966 * Locks required: None
967 * Return code: 0, ETIME
968 */
969 #define MC_CMD_GET_LINK 0x29
970 #define MC_CMD_GET_LINK_IN_LEN 0
971 #define MC_CMD_GET_LINK_OUT_LEN 28
972 /* near-side and link-partner advertised capabilities */
973 #define MC_CMD_GET_LINK_OUT_CAP_OFST 0
974 #define MC_CMD_GET_LINK_OUT_LP_CAP_OFST 4
975 /* Autonegotiated speed in mbit/s. The link may still be down
976 * even if this reads non-zero */
977 #define MC_CMD_GET_LINK_OUT_LINK_SPEED_OFST 8
978 #define MC_CMD_GET_LINK_OUT_LOOPBACK_MODE_OFST 12
979 #define MC_CMD_GET_LINK_OUT_FLAGS_OFST 16
980 /* Whether we have overall link up */
981 #define MC_CMD_GET_LINK_LINK_UP_LBN 0
982 #define MC_CMD_GET_LINK_LINK_UP_WIDTH 1
983 #define MC_CMD_GET_LINK_FULL_DUPLEX_LBN 1
984 #define MC_CMD_GET_LINK_FULL_DUPLEX_WIDTH 1
985 /* Whether we have link at the layers provided by the BPX */
986 #define MC_CMD_GET_LINK_BPX_LINK_LBN 2
987 #define MC_CMD_GET_LINK_BPX_LINK_WIDTH 1
988 /* Whether the PHY has external link */
989 #define MC_CMD_GET_LINK_PHY_LINK_LBN 3
990 #define MC_CMD_GET_LINK_PHY_LINK_WIDTH 1
991 #define MC_CMD_GET_LINK_OUT_FCNTL_OFST 20
992 #define MC_CMD_GET_LINK_OUT_MAC_FAULT_OFST 24
994 /* MC_CMD_SET_LINK:
995 * Write the unified MAC/PHY link configuration
996 *
997 * A loopback speed of "0" is supported, and means
998 * (choose any available speed)
999 *
1000 * Locks required: None
1001 * Return code: 0, EINVAL, ETIME
1002 */
1003 #define MC_CMD_SET_LINK 0x2a
1004 #define MC_CMD_SET_LINK_IN_LEN 16
1005 #define MC_CMD_SET_LINK_IN_CAP_OFST 0
1006 #define MC_CMD_SET_LINK_IN_FLAGS_OFST 4
1007 #define MC_CMD_SET_LINK_LOWPOWER_LBN 0
1008 #define MC_CMD_SET_LINK_LOWPOWER_WIDTH 1
1009 #define MC_CMD_SET_LINK_POWEROFF_LBN 1
1010 #define MC_CMD_SET_LINK_POWEROFF_WIDTH 1
1011 #define MC_CMD_SET_LINK_TXDIS_LBN 2
1012 #define MC_CMD_SET_LINK_TXDIS_WIDTH 1
1013 #define MC_CMD_SET_LINK_IN_LOOPBACK_MODE_OFST 8
1014 #define MC_CMD_SET_LINK_IN_LOOPBACK_SPEED_OFST 12
1015 #define MC_CMD_SET_LINK_OUT_LEN 0
1017 /* MC_CMD_SET_ID_LED:
1018 * Set indentification LED state
1019 *
1020 * Locks required: None
1021 * Return code: 0, EINVAL
1022 */
1023 #define MC_CMD_SET_ID_LED 0x2b
1024 #define MC_CMD_SET_ID_LED_IN_LEN 4
1025 #define MC_CMD_SET_ID_LED_IN_STATE_OFST 0
1026 #define MC_CMD_LED_OFF 0
1027 #define MC_CMD_LED_ON 1
1028 #define MC_CMD_LED_DEFAULT 2
1029 #define MC_CMD_SET_ID_LED_OUT_LEN 0
1031 /* MC_CMD_SET_MAC:
1032 * Set MAC configuration
1033 *
1034 * The MTU is the MTU programmed directly into the XMAC/GMAC
1035 * (inclusive of EtherII, VLAN, bug16011 padding)
1036 *
1037 * Locks required: None
1038 * Return code: 0, EINVAL
1039 */
1040 #define MC_CMD_SET_MAC 0x2c
1041 #define MC_CMD_SET_MAC_IN_LEN 24
1042 #define MC_CMD_SET_MAC_IN_MTU_OFST 0
1043 #define MC_CMD_SET_MAC_IN_DRAIN_OFST 4
1044 #define MC_CMD_SET_MAC_IN_ADDR_OFST 8
1045 #define MC_CMD_SET_MAC_IN_REJECT_OFST 16
1046 #define MC_CMD_SET_MAC_IN_REJECT_UNCST_LBN 0
1047 #define MC_CMD_SET_MAC_IN_REJECT_UNCST_WIDTH 1
1048 #define MC_CMD_SET_MAC_IN_REJECT_BRDCST_LBN 1
1049 #define MC_CMD_SET_MAC_IN_REJECT_BRDCST_WIDTH 1
1050 #define MC_CMD_SET_MAC_IN_FCNTL_OFST 20
1051 #define MC_CMD_SET_MAC_OUT_LEN 0
1053 /* MC_CMD_PHY_STATS:
1054 * Get generic PHY statistics
1055 *
1056 * This call returns the statistics for a generic PHY in a sparse
1057 * array (indexed by the enumerate). Each value is represented by
1058 * a 32bit number.
1059 *
1060 * If the DMA_ADDR is 0, then no DMA is performed, and the statistics
1061 * may be read directly out of shared memory. If DMA_ADDR != 0, then
1062 * the statistics are dmad to that (page-aligned location)
1063 *
1064 * Locks required: None
1065 * Returns: 0, ETIME
1066 * Response methods: shared memory, event
1067 */
1068 #define MC_CMD_PHY_STATS 0x2d
1069 #define MC_CMD_PHY_STATS_IN_LEN 8
1070 #define MC_CMD_PHY_STATS_IN_DMA_ADDR_LO_OFST 0
1071 #define MC_CMD_PHY_STATS_IN_DMA_ADDR_HI_OFST 4
1072 #define MC_CMD_PHY_STATS_OUT_DMA_LEN 0
1073 #define MC_CMD_PHY_STATS_OUT_NO_DMA_LEN (MC_CMD_PHY_NSTATS * 4)
1075 /* Unified MAC statistics enumeration */
1076 #define MC_CMD_MAC_GENERATION_START 0
1077 #define MC_CMD_MAC_TX_PKTS 1
1078 #define MC_CMD_MAC_TX_PAUSE_PKTS 2
1079 #define MC_CMD_MAC_TX_CONTROL_PKTS 3
1080 #define MC_CMD_MAC_TX_UNICAST_PKTS 4
1081 #define MC_CMD_MAC_TX_MULTICAST_PKTS 5
1082 #define MC_CMD_MAC_TX_BROADCAST_PKTS 6
1083 #define MC_CMD_MAC_TX_BYTES 7
1084 #define MC_CMD_MAC_TX_BAD_BYTES 8
1085 #define MC_CMD_MAC_TX_LT64_PKTS 9
1086 #define MC_CMD_MAC_TX_64_PKTS 10
1087 #define MC_CMD_MAC_TX_65_TO_127_PKTS 11
1088 #define MC_CMD_MAC_TX_128_TO_255_PKTS 12
1089 #define MC_CMD_MAC_TX_256_TO_511_PKTS 13
1090 #define MC_CMD_MAC_TX_512_TO_1023_PKTS 14
1091 #define MC_CMD_MAC_TX_1024_TO_15XX_PKTS 15
1092 #define MC_CMD_MAC_TX_15XX_TO_JUMBO_PKTS 16
1093 #define MC_CMD_MAC_TX_GTJUMBO_PKTS 17
1094 #define MC_CMD_MAC_TX_BAD_FCS_PKTS 18
1095 #define MC_CMD_MAC_TX_SINGLE_COLLISION_PKTS 19
1096 #define MC_CMD_MAC_TX_MULTIPLE_COLLISION_PKTS 20
1097 #define MC_CMD_MAC_TX_EXCESSIVE_COLLISION_PKTS 21
1098 #define MC_CMD_MAC_TX_LATE_COLLISION_PKTS 22
1099 #define MC_CMD_MAC_TX_DEFERRED_PKTS 23
1100 #define MC_CMD_MAC_TX_EXCESSIVE_DEFERRED_PKTS 24
1101 #define MC_CMD_MAC_TX_NON_TCPUDP_PKTS 25
1102 #define MC_CMD_MAC_TX_MAC_SRC_ERR_PKTS 26
1103 #define MC_CMD_MAC_TX_IP_SRC_ERR_PKTS 27
1104 #define MC_CMD_MAC_RX_PKTS 28
1105 #define MC_CMD_MAC_RX_PAUSE_PKTS 29
1106 #define MC_CMD_MAC_RX_GOOD_PKTS 30
1107 #define MC_CMD_MAC_RX_CONTROL_PKTS 31
1108 #define MC_CMD_MAC_RX_UNICAST_PKTS 32
1109 #define MC_CMD_MAC_RX_MULTICAST_PKTS 33
1110 #define MC_CMD_MAC_RX_BROADCAST_PKTS 34
1111 #define MC_CMD_MAC_RX_BYTES 35
1112 #define MC_CMD_MAC_RX_BAD_BYTES 36
1113 #define MC_CMD_MAC_RX_64_PKTS 37
1114 #define MC_CMD_MAC_RX_65_TO_127_PKTS 38
1115 #define MC_CMD_MAC_RX_128_TO_255_PKTS 39
1116 #define MC_CMD_MAC_RX_256_TO_511_PKTS 40
1117 #define MC_CMD_MAC_RX_512_TO_1023_PKTS 41
1118 #define MC_CMD_MAC_RX_1024_TO_15XX_PKTS 42
1119 #define MC_CMD_MAC_RX_15XX_TO_JUMBO_PKTS 43
1120 #define MC_CMD_MAC_RX_GTJUMBO_PKTS 44
1121 #define MC_CMD_MAC_RX_UNDERSIZE_PKTS 45
1122 #define MC_CMD_MAC_RX_BAD_FCS_PKTS 46
1123 #define MC_CMD_MAC_RX_OVERFLOW_PKTS 47
1124 #define MC_CMD_MAC_RX_FALSE_CARRIER_PKTS 48
1125 #define MC_CMD_MAC_RX_SYMBOL_ERROR_PKTS 49
1126 #define MC_CMD_MAC_RX_ALIGN_ERROR_PKTS 50
1127 #define MC_CMD_MAC_RX_LENGTH_ERROR_PKTS 51
1128 #define MC_CMD_MAC_RX_INTERNAL_ERROR_PKTS 52
1129 #define MC_CMD_MAC_RX_JABBER_PKTS 53
1130 #define MC_CMD_MAC_RX_NODESC_DROPS 54
1131 #define MC_CMD_MAC_RX_LANES01_CHAR_ERR 55
1132 #define MC_CMD_MAC_RX_LANES23_CHAR_ERR 56
1133 #define MC_CMD_MAC_RX_LANES01_DISP_ERR 57
1134 #define MC_CMD_MAC_RX_LANES23_DISP_ERR 58
1135 #define MC_CMD_MAC_RX_MATCH_FAULT 59
1136 #define MC_CMD_GMAC_DMABUF_START 64
1137 #define MC_CMD_GMAC_DMABUF_END 95
1138 /* Insert new members here. */
1139 #define MC_CMD_MAC_GENERATION_END 96
1140 #define MC_CMD_MAC_NSTATS (MC_CMD_MAC_GENERATION_END+1)
1142 /* MC_CMD_MAC_STATS:
1143 * Get unified GMAC/XMAC statistics
1144 *
1145 * This call returns unified statistics maintained by the MC as it
1146 * switches between the GMAC and XMAC. The MC will write out all
1147 * supported stats. The driver should zero initialise the buffer to
1148 * guarantee consistent results.
1149 *
1150 * Locks required: None
1151 * Returns: 0
1152 * Response methods: shared memory, event
1153 */
1154 #define MC_CMD_MAC_STATS 0x2e
1155 #define MC_CMD_MAC_STATS_IN_LEN 16
1156 #define MC_CMD_MAC_STATS_IN_DMA_ADDR_LO_OFST 0
1157 #define MC_CMD_MAC_STATS_IN_DMA_ADDR_HI_OFST 4
1158 #define MC_CMD_MAC_STATS_IN_CMD_OFST 8
1159 #define MC_CMD_MAC_STATS_CMD_DMA_LBN 0
1160 #define MC_CMD_MAC_STATS_CMD_DMA_WIDTH 1
1161 #define MC_CMD_MAC_STATS_CMD_CLEAR_LBN 1
1162 #define MC_CMD_MAC_STATS_CMD_CLEAR_WIDTH 1
1163 #define MC_CMD_MAC_STATS_CMD_PERIODIC_CHANGE_LBN 2
1164 #define MC_CMD_MAC_STATS_CMD_PERIODIC_CHANGE_WIDTH 1
1165 /* Remaining PERIOD* fields only relevent when PERIODIC_CHANGE is set */
1166 #define MC_CMD_MAC_STATS_CMD_PERIODIC_ENABLE_LBN 3
1167 #define MC_CMD_MAC_STATS_CMD_PERIODIC_ENABLE_WIDTH 1
1168 #define MC_CMD_MAC_STATS_CMD_PERIODIC_CLEAR_LBN 4
1169 #define MC_CMD_MAC_STATS_CMD_PERIODIC_CLEAR_WIDTH 1
1170 #define MC_CMD_MAC_STATS_CMD_PERIODIC_NOEVENT_LBN 5
1171 #define MC_CMD_MAC_STATS_CMD_PERIODIC_NOEVENT_WIDTH 1
1172 #define MC_CMD_MAC_STATS_CMD_PERIOD_MS_LBN 16
1173 #define MC_CMD_MAC_STATS_CMD_PERIOD_MS_WIDTH 16
1174 #define MC_CMD_MAC_STATS_IN_DMA_LEN_OFST 12
1176 #define MC_CMD_MAC_STATS_OUT_LEN 0
1178 /* Callisto flags */
1179 #define MC_CMD_SFT9001_ROBUST_LBN 0
1180 #define MC_CMD_SFT9001_ROBUST_WIDTH 1
1181 #define MC_CMD_SFT9001_SHORT_REACH_LBN 1
1182 #define MC_CMD_SFT9001_SHORT_REACH_WIDTH 1
1184 /* MC_CMD_SFT9001_GET:
1185 * Read current callisto specific setting
1186 *
1187 * Locks required: None
1188 * Returns: 0, ETIME
1189 */
1190 #define MC_CMD_SFT9001_GET 0x30
1191 #define MC_CMD_SFT9001_GET_IN_LEN 0
1192 #define MC_CMD_SFT9001_GET_OUT_LEN 4
1193 #define MC_CMD_SFT9001_GET_OUT_FLAGS_OFST 0
1195 /* MC_CMD_SFT9001_SET:
1196 * Write current callisto specific setting
1197 *
1198 * Locks required: None
1199 * Returns: 0, ETIME, EINVAL
1200 */
1201 #define MC_CMD_SFT9001_SET 0x31
1202 #define MC_CMD_SFT9001_SET_IN_LEN 4
1203 #define MC_CMD_SFT9001_SET_IN_FLAGS_OFST 0
1204 #define MC_CMD_SFT9001_SET_OUT_LEN 0
1207 /* MC_CMD_WOL_FILTER_SET:
1208 * Set a WoL filter
1209 *
1210 * Locks required: None
1211 * Returns: 0, EBUSY, EINVAL, ENOSYS
1212 */
1213 #define MC_CMD_WOL_FILTER_SET 0x32
1215 #define MC_CMD_WOL_FILTER_SET_IN_FILTER_MODE_OFST 0
1216 #define MC_CMD_WOL_FILTER_SET_IN_WOL_TYPE_OFST 4
1218 /* There is a union at offset 8, following defines overlap due to
1219 * this */
1220 #define MC_CMD_WOL_FILTER_SET_IN_DATA_OFST 8
1222 #define MC_CMD_WOL_FILTER_SET_IN_MAGIC_MAC_OFST \
1223 MC_CMD_WOL_FILTER_SET_IN_DATA_OFST
1225 #define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_SRC_IP_OFST \
1226 MC_CMD_WOL_FILTER_SET_IN_DATA_OFST
1227 #define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_DST_IP_OFST \
1228 (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 4)
1229 #define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_SRC_PORT_OFST \
1230 (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 8)
1231 #define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_DST_PORT_OFST \
1232 (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 10)
1234 #define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_SRC_IP_OFST \
1235 MC_CMD_WOL_FILTER_SET_IN_DATA_OFST
1236 #define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_DST_IP_OFST \
1237 (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 16)
1238 #define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_SRC_PORT_OFST \
1239 (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 32)
1240 #define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_DST_PORT_OFST \
1241 (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 34)
1243 #define MC_CMD_WOL_FILTER_SET_IN_BITMAP_MASK_OFST \
1244 MC_CMD_WOL_FILTER_SET_IN_DATA_OFST
1245 #define MC_CMD_WOL_FILTER_SET_IN_BITMAP_OFST \
1246 (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 48)
1247 #define MC_CMD_WOL_FILTER_SET_IN_BITMAP_LEN_OFST \
1248 (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 176)
1249 #define MC_CMD_WOL_FILTER_SET_IN_BITMAP_LAYER3_OFST \
1250 (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 177)
1251 #define MC_CMD_WOL_FILTER_SET_IN_BITMAP_LAYER4_OFST \
1252 (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 178)
1254 #define MC_CMD_WOL_FILTER_SET_IN_LINK_MASK_OFST \
1255 MC_CMD_WOL_FILTER_SET_IN_DATA_OFST
1256 #define MC_CMD_WOL_FILTER_SET_IN_LINK_UP_LBN 0
1257 #define MC_CMD_WOL_FILTER_SET_IN_LINK_UP_WIDTH 1
1258 #define MC_CMD_WOL_FILTER_SET_IN_LINK_DOWN_LBN 1
1259 #define MC_CMD_WOL_FILTER_SET_IN_LINK_DOWN_WIDTH 1
1261 #define MC_CMD_WOL_FILTER_SET_OUT_LEN 4
1262 #define MC_CMD_WOL_FILTER_SET_OUT_FILTER_ID_OFST 0
1264 /* WOL Filter types enumeration */
1265 #define MC_CMD_WOL_TYPE_MAGIC 0x0
1266 /* unused 0x1 */
1267 #define MC_CMD_WOL_TYPE_WIN_MAGIC 0x2
1268 #define MC_CMD_WOL_TYPE_IPV4_SYN 0x3
1269 #define MC_CMD_WOL_TYPE_IPV6_SYN 0x4
1270 #define MC_CMD_WOL_TYPE_BITMAP 0x5
1271 #define MC_CMD_WOL_TYPE_LINK 0x6
1272 #define MC_CMD_WOL_TYPE_MAX 0x7
1274 #define MC_CMD_FILTER_MODE_SIMPLE 0x0
1275 #define MC_CMD_FILTER_MODE_STRUCTURED 0xffffffff
1277 /* MC_CMD_WOL_FILTER_REMOVE:
1278 * Remove a WoL filter
1279 *
1280 * Locks required: None
1281 * Returns: 0, EINVAL, ENOSYS
1282 */
1283 #define MC_CMD_WOL_FILTER_REMOVE 0x33
1284 #define MC_CMD_WOL_FILTER_REMOVE_IN_LEN 4
1285 #define MC_CMD_WOL_FILTER_REMOVE_IN_FILTER_ID_OFST 0
1286 #define MC_CMD_WOL_FILTER_REMOVE_OUT_LEN 0
1289 /* MC_CMD_WOL_FILTER_RESET:
1290 * Reset (i.e. remove all) WoL filters
1291 *
1292 * Locks required: None
1293 * Returns: 0, ENOSYS
1294 */
1295 #define MC_CMD_WOL_FILTER_RESET 0x34
1296 #define MC_CMD_WOL_FILTER_RESET_IN_LEN 0
1297 #define MC_CMD_WOL_FILTER_RESET_OUT_LEN 0
1299 /* MC_CMD_SET_MCAST_HASH:
1300 * Set the MCASH hash value without otherwise
1301 * reconfiguring the MAC
1302 */
1303 #define MC_CMD_SET_MCAST_HASH 0x35
1304 #define MC_CMD_SET_MCAST_HASH_IN_LEN 32
1305 #define MC_CMD_SET_MCAST_HASH_IN_HASH0_OFST 0
1306 #define MC_CMD_SET_MCAST_HASH_IN_HASH1_OFST 16
1307 #define MC_CMD_SET_MCAST_HASH_OUT_LEN 0
1309 /* MC_CMD_NVRAM_TYPES:
1310 * Return bitfield indicating available types of virtual NVRAM partitions
1311 *
1312 * Locks required: none
1313 * Returns: 0
1314 */
1315 #define MC_CMD_NVRAM_TYPES 0x36
1316 #define MC_CMD_NVRAM_TYPES_IN_LEN 0
1317 #define MC_CMD_NVRAM_TYPES_OUT_LEN 4
1318 #define MC_CMD_NVRAM_TYPES_OUT_TYPES_OFST 0
1320 /* Supported NVRAM types */
1321 #define MC_CMD_NVRAM_TYPE_DISABLED_CALLISTO 0
1322 #define MC_CMD_NVRAM_TYPE_MC_FW 1
1323 #define MC_CMD_NVRAM_TYPE_MC_FW_BACKUP 2
1324 #define MC_CMD_NVRAM_TYPE_STATIC_CFG_PORT0 3
1325 #define MC_CMD_NVRAM_TYPE_STATIC_CFG_PORT1 4
1326 #define MC_CMD_NVRAM_TYPE_DYNAMIC_CFG_PORT0 5
1327 #define MC_CMD_NVRAM_TYPE_DYNAMIC_CFG_PORT1 6
1328 #define MC_CMD_NVRAM_TYPE_EXP_ROM 7
1329 #define MC_CMD_NVRAM_TYPE_EXP_ROM_CFG_PORT0 8
1330 #define MC_CMD_NVRAM_TYPE_EXP_ROM_CFG_PORT1 9
1331 #define MC_CMD_NVRAM_TYPE_PHY_PORT0 10
1332 #define MC_CMD_NVRAM_TYPE_PHY_PORT1 11
1333 #define MC_CMD_NVRAM_TYPE_LOG 12
1335 /* MC_CMD_NVRAM_INFO:
1336 * Read info about a virtual NVRAM partition
1337 *
1338 * Locks required: none
1339 * Returns: 0, EINVAL (bad type)
1340 */
1341 #define MC_CMD_NVRAM_INFO 0x37
1342 #define MC_CMD_NVRAM_INFO_IN_LEN 4
1343 #define MC_CMD_NVRAM_INFO_IN_TYPE_OFST 0
1344 #define MC_CMD_NVRAM_INFO_OUT_LEN 24
1345 #define MC_CMD_NVRAM_INFO_OUT_TYPE_OFST 0
1346 #define MC_CMD_NVRAM_INFO_OUT_SIZE_OFST 4
1347 #define MC_CMD_NVRAM_INFO_OUT_ERASESIZE_OFST 8
1348 #define MC_CMD_NVRAM_INFO_OUT_FLAGS_OFST 12
1349 #define MC_CMD_NVRAM_PROTECTED_LBN 0
1350 #define MC_CMD_NVRAM_PROTECTED_WIDTH 1
1351 #define MC_CMD_NVRAM_INFO_OUT_PHYSDEV_OFST 16
1352 #define MC_CMD_NVRAM_INFO_OUT_PHYSADDR_OFST 20
1354 /* MC_CMD_NVRAM_UPDATE_START:
1355 * Start a group of update operations on a virtual NVRAM partition
1356 *
1357 * Locks required: PHY_LOCK if type==*PHY*
1358 * Returns: 0, EINVAL (bad type), EACCES (if PHY_LOCK required and not held)
1359 */
1360 #define MC_CMD_NVRAM_UPDATE_START 0x38
1361 #define MC_CMD_NVRAM_UPDATE_START_IN_LEN 4
1362 #define MC_CMD_NVRAM_UPDATE_START_IN_TYPE_OFST 0
1363 #define MC_CMD_NVRAM_UPDATE_START_OUT_LEN 0
1365 /* MC_CMD_NVRAM_READ:
1366 * Read data from a virtual NVRAM partition
1367 *
1368 * Locks required: PHY_LOCK if type==*PHY*
1369 * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held)
1370 */
1371 #define MC_CMD_NVRAM_READ 0x39
1372 #define MC_CMD_NVRAM_READ_IN_LEN 12
1373 #define MC_CMD_NVRAM_READ_IN_TYPE_OFST 0
1374 #define MC_CMD_NVRAM_READ_IN_OFFSET_OFST 4
1375 #define MC_CMD_NVRAM_READ_IN_LENGTH_OFST 8
1376 #define MC_CMD_NVRAM_READ_OUT_LEN(_read_bytes) (_read_bytes)
1377 #define MC_CMD_NVRAM_READ_OUT_READ_BUFFER_OFST 0
1379 /* MC_CMD_NVRAM_WRITE:
1380 * Write data to a virtual NVRAM partition
1381 *
1382 * Locks required: PHY_LOCK if type==*PHY*
1383 * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held)
1384 */
1385 #define MC_CMD_NVRAM_WRITE 0x3a
1386 #define MC_CMD_NVRAM_WRITE_IN_TYPE_OFST 0
1387 #define MC_CMD_NVRAM_WRITE_IN_OFFSET_OFST 4
1388 #define MC_CMD_NVRAM_WRITE_IN_LENGTH_OFST 8
1389 #define MC_CMD_NVRAM_WRITE_IN_WRITE_BUFFER_OFST 12
1390 #define MC_CMD_NVRAM_WRITE_IN_LEN(_write_bytes) (12 + _write_bytes)
1391 #define MC_CMD_NVRAM_WRITE_OUT_LEN 0
1393 /* MC_CMD_NVRAM_ERASE:
1394 * Erase sector(s) from a virtual NVRAM partition
1395 *
1396 * Locks required: PHY_LOCK if type==*PHY*
1397 * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held)
1398 */
1399 #define MC_CMD_NVRAM_ERASE 0x3b
1400 #define MC_CMD_NVRAM_ERASE_IN_LEN 12
1401 #define MC_CMD_NVRAM_ERASE_IN_TYPE_OFST 0
1402 #define MC_CMD_NVRAM_ERASE_IN_OFFSET_OFST 4
1403 #define MC_CMD_NVRAM_ERASE_IN_LENGTH_OFST 8
1404 #define MC_CMD_NVRAM_ERASE_OUT_LEN 0
1406 /* MC_CMD_NVRAM_UPDATE_FINISH:
1407 * Finish a group of update operations on a virtual NVRAM partition
1408 *
1409 * Locks required: PHY_LOCK if type==*PHY*
1410 * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held)
1411 */
1412 #define MC_CMD_NVRAM_UPDATE_FINISH 0x3c
1413 #define MC_CMD_NVRAM_UPDATE_FINISH_IN_LEN 8
1414 #define MC_CMD_NVRAM_UPDATE_FINISH_IN_TYPE_OFST 0
1415 #define MC_CMD_NVRAM_UPDATE_FINISH_IN_REBOOT_OFST 4
1416 #define MC_CMD_NVRAM_UPDATE_FINISH_OUT_LEN 0
1418 /* MC_CMD_REBOOT:
1419 * Reboot the MC.
1420 *
1421 * The AFTER_ASSERTION flag is intended to be used when the driver notices
1422 * an assertion failure (at which point it is expected to perform a complete
1423 * tear down and reinitialise), to allow both ports to reset the MC once
1424 * in an atomic fashion.
1425 *
1426 * Production mc firmwares are generally compiled with REBOOT_ON_ASSERT=1,
1427 * which means that they will automatically reboot out of the assertion
1428 * handler, so this is in practise an optional operation. It is still
1429 * recommended that drivers execute this to support custom firmwares
1430 * with REBOOT_ON_ASSERT=0.
1431 *
1432 * Locks required: NONE
1433 * Returns: Nothing. You get back a response with ERR=1, DATALEN=0
1434 */
1435 #define MC_CMD_REBOOT 0x3d
1436 #define MC_CMD_REBOOT_IN_LEN 4
1437 #define MC_CMD_REBOOT_IN_FLAGS_OFST 0
1438 #define MC_CMD_REBOOT_FLAGS_AFTER_ASSERTION 1
1439 #define MC_CMD_REBOOT_OUT_LEN 0
1441 /* MC_CMD_SCHEDINFO:
1442 * Request scheduler info. from the MC.
1443 *
1444 * Locks required: NONE
1445 * Returns: An array of (timeslice,maximum overrun), one for each thread,
1446 * in ascending order of thread address.s
1447 */
1448 #define MC_CMD_SCHEDINFO 0x3e
1449 #define MC_CMD_SCHEDINFO_IN_LEN 0
1452 /* MC_CMD_SET_REBOOT_MODE: (debug)
1453 * Set the mode for the next MC reboot.
1454 *
1455 * Locks required: NONE
1456 *
1457 * Sets the reboot mode to the specified value. Returns the old mode.
1458 */
1459 #define MC_CMD_REBOOT_MODE 0x3f
1460 #define MC_CMD_REBOOT_MODE_IN_LEN 4
1461 #define MC_CMD_REBOOT_MODE_IN_VALUE_OFST 0
1462 #define MC_CMD_REBOOT_MODE_OUT_LEN 4
1463 #define MC_CMD_REBOOT_MODE_OUT_VALUE_OFST 0
1464 #define MC_CMD_REBOOT_MODE_NORMAL 0
1465 #define MC_CMD_REBOOT_MODE_SNAPPER 3
1467 /* MC_CMD_DEBUG_LOG:
1468 * Null request/response command (debug)
1469 * - sequence number is always zero
1470 * - only supported on the UART interface
1471 * (the same set of bytes is delivered as an
1472 * event over PCI)
1473 */
1474 #define MC_CMD_DEBUG_LOG 0x40
1475 #define MC_CMD_DEBUG_LOG_IN_LEN 0
1476 #define MC_CMD_DEBUG_LOG_OUT_LEN 0
1478 /* Generic sensor enumeration. Note that a dual port NIC
1479 * will EITHER expose PHY_COMMON_TEMP OR PHY0_TEMP and
1480 * PHY1_TEMP depending on whether there is a single sensor
1481 * in the vicinity of the two port, or one per port.
1482 */
1498 /* Sensor state */
1499 #define MC_CMD_SENSOR_STATE_OK 0
1500 #define MC_CMD_SENSOR_STATE_WARNING 1
1501 #define MC_CMD_SENSOR_STATE_FATAL 2
1502 #define MC_CMD_SENSOR_STATE_BROKEN 3
1504 /* MC_CMD_SENSOR_INFO:
1505 * Returns information about every available sensor.
1506 *
1507 * Each sensor has a single (16bit) value, and a corresponding state.
1508 * The mapping between value and sensor is nominally determined by the
1509 * MC, but in practise is implemented as zero (BROKEN), one (TEMPERATURE),
1510 * or two (VOLTAGE) ranges per sensor per state.
1511 *
1512 * This call returns a mask (32bit) of the sensors that are supported
1513 * by this platform, then an array (indexed by MC_CMD_SENSOR) of byte
1514 * offsets to the per-sensor arrays. Each sensor array has four 16bit
1515 * numbers, min1, max1, min2, max2.
1516 *
1517 * Locks required: None
1518 * Returns: 0
1519 */
1520 #define MC_CMD_SENSOR_INFO 0x41
1521 #define MC_CMD_SENSOR_INFO_IN_LEN 0
1522 #define MC_CMD_SENSOR_INFO_OUT_MASK_OFST 0
1523 #define MC_CMD_SENSOR_INFO_OUT_OFFSET_OFST(_x) \
1524 (4 + (_x))
1525 #define MC_CMD_SENSOR_INFO_OUT_MIN1_OFST(_ofst) \
1526 ((_ofst) + 0)
1527 #define MC_CMD_SENSOR_INFO_OUT_MAX1_OFST(_ofst) \
1528 ((_ofst) + 2)
1529 #define MC_CMD_SENSOR_INFO_OUT_MIN2_OFST(_ofst) \
1530 ((_ofst) + 4)
1531 #define MC_CMD_SENSOR_INFO_OUT_MAX2_OFST(_ofst) \
1532 ((_ofst) + 6)
1534 /* MC_CMD_READ_SENSORS
1535 * Returns the current reading from each sensor
1536 *
1537 * Returns a sparse array of sensor readings (indexed by the sensor
1538 * type) into host memory. Each array element is a dword.
1539 *
1540 * The MC will send a SENSOREVT event every time any sensor changes state. The
1541 * driver is responsible for ensuring that it doesn't miss any events. The board
1542 * will function normally if all sensors are in STATE_OK or state_WARNING.
1543 * Otherwise the board should not be expected to function.
1544 */
1545 #define MC_CMD_READ_SENSORS 0x42
1546 #define MC_CMD_READ_SENSORS_IN_LEN 8
1547 #define MC_CMD_READ_SENSORS_IN_DMA_ADDR_LO_OFST 0
1548 #define MC_CMD_READ_SENSORS_IN_DMA_ADDR_HI_OFST 4
1549 #define MC_CMD_READ_SENSORS_OUT_LEN 0
1551 /* Sensor reading fields */
1552 #define MC_CMD_READ_SENSOR_VALUE_LBN 0
1553 #define MC_CMD_READ_SENSOR_VALUE_WIDTH 16
1554 #define MC_CMD_READ_SENSOR_STATE_LBN 16
1555 #define MC_CMD_READ_SENSOR_STATE_WIDTH 8
1558 /* MC_CMD_GET_PHY_STATE:
1559 * Report current state of PHY. A "zombie" PHY is a PHY that has failed to
1560 * boot (e.g. due to missing or corrupted firmware).
1561 *
1562 * Locks required: None
1563 * Return code: 0
1564 */
1565 #define MC_CMD_GET_PHY_STATE 0x43
1567 #define MC_CMD_GET_PHY_STATE_IN_LEN 0
1568 #define MC_CMD_GET_PHY_STATE_OUT_LEN 4
1569 #define MC_CMD_GET_PHY_STATE_STATE_OFST 0
1570 /* PHY state enumeration: */
1571 #define MC_CMD_PHY_STATE_OK 1
1572 #define MC_CMD_PHY_STATE_ZOMBIE 2
1575 /* 802.1Qbb control. 8 Tx queues that map to priorities 0 - 7. Use all 1s to
1576 * disable 802.Qbb for a given priority. */
1577 #define MC_CMD_SETUP_8021QBB 0x44
1578 #define MC_CMD_SETUP_8021QBB_IN_LEN 32
1579 #define MC_CMD_SETUP_8021QBB_OUT_LEN 0
1580 #define MC_CMD_SETUP_8021QBB_IN_TXQS_OFFST 0
1583 /* MC_CMD_WOL_FILTER_GET:
1584 * Retrieve ID of any WoL filters
1585 *
1586 * Locks required: None
1587 * Returns: 0, ENOSYS
1588 */
1589 #define MC_CMD_WOL_FILTER_GET 0x45
1590 #define MC_CMD_WOL_FILTER_GET_IN_LEN 0
1591 #define MC_CMD_WOL_FILTER_GET_OUT_LEN 4
1592 #define MC_CMD_WOL_FILTER_GET_OUT_FILTER_ID_OFST 0
1595 /* MC_CMD_ADD_LIGHTSOUT_OFFLOAD:
1596 * Offload a protocol to NIC for lights-out state
1597 *
1598 * Locks required: None
1599 * Returns: 0, ENOSYS
1600 */
1601 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD 0x46
1603 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_LEN 16
1604 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_PROTOCOL_OFST 0
1606 /* There is a union at offset 4, following defines overlap due to
1607 * this */
1608 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_DATA_OFST 4
1609 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_ARPMAC_OFST 4
1610 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_ARPIP_OFST 10
1611 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_NSMAC_OFST 4
1612 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_NSSNIPV6_OFST 10
1613 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_NSIPV6_OFST 26
1615 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_OUT_LEN 4
1616 #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_OUT_FILTER_ID_OFST 0
1619 /* MC_CMD_REMOVE_LIGHTSOUT_PROTOCOL_OFFLOAD:
1620 * Offload a protocol to NIC for lights-out state
1621 *
1622 * Locks required: None
1623 * Returns: 0, ENOSYS
1624 */
1625 #define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD 0x47
1626 #define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_IN_LEN 8
1627 #define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_OUT_LEN 0
1629 #define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_IN_PROTOCOL_OFST 0
1630 #define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_IN_FILTER_ID_OFST 4
1632 /* Lights-out offload protocols enumeration */
1633 #define MC_CMD_LIGHTSOUT_OFFLOAD_PROTOCOL_ARP 0x1
1634 #define MC_CMD_LIGHTSOUT_OFFLOAD_PROTOCOL_NS 0x2
1637 /* MC_CMD_MAC_RESET_RESTORE:
1638 * Restore MAC after block reset
1639 *
1640 * Locks required: None
1641 * Returns: 0
1642 */
1644 #define MC_CMD_MAC_RESET_RESTORE 0x48
1645 #define MC_CMD_MAC_RESET_RESTORE_IN_LEN 0
1646 #define MC_CMD_MAC_RESET_RESTORE_OUT_LEN 0
1649 /* MC_CMD_TEST_ASSERT:
1650 * Deliberately trigger an assert-detonation in the firmware for testing
1651 * purposes (i.e. to allow tests that the driver copes gracefully).
1652 *
1653 * Locks required: None
1654 * Returns: 0
1655 */
1657 #define MC_CMD_TESTASSERT 0x49
1658 #define MC_CMD_TESTASSERT_IN_LEN 0
1659 #define MC_CMD_TESTASSERT_OUT_LEN 0
1661 /* MC_CMD_WORKAROUND 0x4a
1662 *
1663 * Enable/Disable a given workaround. The mcfw will return EINVAL if it
1664 * doesn't understand the given workaround number - which should not
1665 * be treated as a hard error by client code.
1666 *
1667 * This op does not imply any semantics about each workaround, that's between
1668 * the driver and the mcfw on a per-workaround basis.
1669 *
1670 * Locks required: None
1671 * Returns: 0, EINVAL
1672 */
1673 #define MC_CMD_WORKAROUND 0x4a
1674 #define MC_CMD_WORKAROUND_IN_LEN 8
1675 #define MC_CMD_WORKAROUND_IN_TYPE_OFST 0
1676 #define MC_CMD_WORKAROUND_BUG17230 1
1677 #define MC_CMD_WORKAROUND_IN_ENABLED_OFST 4
1678 #define MC_CMD_WORKAROUND_OUT_LEN 0
1680 /* MC_CMD_GET_PHY_MEDIA_INFO:
1681 * Read media-specific data from PHY (e.g. SFP/SFP+ module ID information for
1682 * SFP+ PHYs).
1683 *
1684 * The "media type" can be found via GET_PHY_CFG (GET_PHY_CFG_OUT_MEDIA_TYPE);
1685 * the valid "page number" input values, and the output data, are interpreted
1686 * on a per-type basis.
1687 *
1688 * For SFP+: PAGE=0 or 1 returns a 128-byte block read from module I2C address
1689 * 0xA0 offset 0 or 0x80.
1690 * Anything else: currently undefined.
1691 *
1692 * Locks required: None
1693 * Return code: 0
1694 */
1695 #define MC_CMD_GET_PHY_MEDIA_INFO 0x4b
1696 #define MC_CMD_GET_PHY_MEDIA_INFO_IN_LEN 4
1697 #define MC_CMD_GET_PHY_MEDIA_INFO_IN_PAGE_OFST 0
1698 #define MC_CMD_GET_PHY_MEDIA_INFO_OUT_LEN(_num_bytes) (4 + (_num_bytes))
1699 #define MC_CMD_GET_PHY_MEDIA_INFO_OUT_DATALEN_OFST 0
1700 #define MC_CMD_GET_PHY_MEDIA_INFO_OUT_DATA_OFST 4
1702 /* MC_CMD_NVRAM_TEST:
1703 * Test a particular NVRAM partition for valid contents (where "valid"
1704 * depends on the type of partition).
1705 *
1706 * Locks required: None
1707 * Return code: 0
1708 */
1709 #define MC_CMD_NVRAM_TEST 0x4c
1710 #define MC_CMD_NVRAM_TEST_IN_LEN 4
1711 #define MC_CMD_NVRAM_TEST_IN_TYPE_OFST 0
1712 #define MC_CMD_NVRAM_TEST_OUT_LEN 4
1713 #define MC_CMD_NVRAM_TEST_OUT_RESULT_OFST 0
1714 #define MC_CMD_NVRAM_TEST_PASS 0
1715 #define MC_CMD_NVRAM_TEST_FAIL 1
1716 #define MC_CMD_NVRAM_TEST_NOTSUPP 2
1718 /* MC_CMD_MRSFP_TWEAK: (debug)
1719 * Read status and/or set parameters for the "mrsfp" driver in mr_rusty builds.
1720 * I2C I/O expander bits are always read; if equaliser parameters are supplied,
1721 * they are configured first.
1722 *
1723 * Locks required: None
1724 * Return code: 0, EINVAL
1725 */
1726 #define MC_CMD_MRSFP_TWEAK 0x4d
1727 #define MC_CMD_MRSFP_TWEAK_IN_LEN_READ_ONLY 0
1728 #define MC_CMD_MRSFP_TWEAK_IN_LEN_EQ_CONFIG 16
1733 #define MC_CMD_MRSFP_TWEAK_OUT_LEN 12
1738 /* MC_CMD_TEST_HACK: (debug (unsurprisingly))
1739 * Change bits of network port state for test purposes in ways that would never be
1740 * useful in normal operation and so need a special command to change. */
1741 #define MC_CMD_TEST_HACK 0x2f
1742 #define MC_CMD_TEST_HACK_IN_LEN 8
1743 #define MC_CMD_TEST_HACK_IN_TXPAD_OFST 0
1749 #define MC_CMD_TEST_HACK_OUT_LEN 0
1751 /* MC_CMD_SENSOR_SET_LIMS: (debug) (mostly) adjust the sensor limits. This
1752 * is a warranty-voiding operation.
1753 *
1754 * IN: sensor identifier (one of the enumeration starting with MC_CMD_SENSOR_CONTROLLER_TEMP
1755 * followed by 4 32-bit values: min(warning) max(warning), min(fatal), max(fatal). Which
1756 * of these limits are meaningful and what their interpretation is is sensor-specific.
1757 *
1758 * OUT: nothing
1759 *
1760 * Returns: ENOENT if the sensor specified does not exist, EINVAL if the limits are
1761 * out of range.
1762 */
1763 #define MC_CMD_SENSOR_SET_LIMS 0x4e
1764 #define MC_CMD_SENSOR_SET_LIMS_IN_LEN 20
1765 #define MC_CMD_SENSOR_SET_LIMS_IN_SENSOR_OFST 0
1766 #define MC_CMD_SENSOR_SET_LIMS_IN_LOW0_OFST 4
1767 #define MC_CMD_SENSOR_SET_LIMS_IN_HI0_OFST 8
1768 #define MC_CMD_SENSOR_SET_LIMS_IN_LOW1_OFST 12
1769 #define MC_CMD_SENSOR_SET_LIMS_IN_HI1_OFST 16
1771 /* Do NOT add new commands beyond 0x4f as part of 3.0 : 0x50 - 0x7f will be
1772 * used for post-3.0 extensions. If you run out of space, look for gaps or
1773 * commands that are unused in the existing range. */