drivers/hwmon/thmc50.c

   1 /*
   2  * thmc50.c - Part of lm_sensors, Linux kernel modules for hardware
   3  *            monitoring
   4  * Copyright (C) 2007 Krzysztof Helt <krzysztof.h1@wp.pl>
   5  * Based on 2.4 driver by Frodo Looijaard <frodol@dds.nl> and
   6  * Philip Edelbrock <phil@netroedge.com>
   7  *
   8  * This program is free software; you can redistribute it and/or modify
   9  * it under the terms of the GNU General Public License as published by
  10  * the Free Software Foundation; either version 2 of the License, or
  11  * (at your option) any later version.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software
  20  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  21  */
  22
  23 #include <linux/module.h>
  24 #include <linux/init.h>
  25 #include <linux/slab.h>
  26 #include <linux/i2c.h>
  27 #include <linux/hwmon.h>
  28 #include <linux/hwmon-sysfs.h>
  29 #include <linux/err.h>
  30 #include <linux/mutex.h>
  31
  32 MODULE_LICENSE("GPL");
  33
  34 /* Addresses to scan */
  35 static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
  36
  37 /* Insmod parameters */
  38 enum chips { thmc50, adm1022 };
  39
  40 static unsigned short adm1022_temp3[16];
  41 static unsigned int adm1022_temp3_num;
  42 module_param_array(adm1022_temp3, ushort, &adm1022_temp3_num, 0);
  43 MODULE_PARM_DESC(adm1022_temp3, "List of adapter,address pairs "
  44                         "to enable 3rd temperature (ADM1022 only)");
  45
  46 /* Many THMC50 constants specified below */
  47
  48 /* The THMC50 registers */
  49 #define THMC50_REG_CONF                         0x40
  50 #define THMC50_REG_COMPANY_ID                   0x3E
  51 #define THMC50_REG_DIE_CODE                     0x3F
  52 #define THMC50_REG_ANALOG_OUT                   0x19
  53 /*
  54  * The mirror status register cannot be used as
  55  * reading it does not clear alarms.
  56  */
  57 #define THMC50_REG_INTR                         0x41
  58
  59 static const u8 THMC50_REG_TEMP[] = { 0x27, 0x26, 0x20 };
  60 static const u8 THMC50_REG_TEMP_MIN[] = { 0x3A, 0x38, 0x2C };
  61 static const u8 THMC50_REG_TEMP_MAX[] = { 0x39, 0x37, 0x2B };
  62 static const u8 THMC50_REG_TEMP_CRITICAL[] = { 0x13, 0x14, 0x14 };
  63 static const u8 THMC50_REG_TEMP_DEFAULT[] = { 0x17, 0x18, 0x18 };
  64
  65 #define THMC50_REG_CONF_nFANOFF                 0x20
  66 #define THMC50_REG_CONF_PROGRAMMED              0x08
  67
  68 /* Each client has this additional data */
  69 struct thmc50_data {
  70         struct device *hwmon_dev;
  71
  72         struct mutex update_lock;
  73         enum chips type;
  74         unsigned long last_updated;     /* In jiffies */
  75         char has_temp3;         /* !=0 if it is ADM1022 in temp3 mode */
  76         char valid;             /* !=0 if following fields are valid */
  77
  78         /* Register values */
  79         s8 temp_input[3];
  80         s8 temp_max[3];
  81         s8 temp_min[3];
  82         s8 temp_critical[3];
  83         u8 analog_out;
  84         u8 alarms;
  85 };
  86
  87 static int thmc50_detect(struct i2c_client *client,
  88                          struct i2c_board_info *info);
  89 static int thmc50_probe(struct i2c_client *client,
  90                         const struct i2c_device_id *id);
  91 static int thmc50_remove(struct i2c_client *client);
  92 static void thmc50_init_client(struct i2c_client *client);
  93 static struct thmc50_data *thmc50_update_device(struct device *dev);
  94
  95 static const struct i2c_device_id thmc50_id[] = {
  96         { "adm1022", adm1022 },
  97         { "thmc50", thmc50 },
  98         { }
  99 };
 100 MODULE_DEVICE_TABLE(i2c, thmc50_id);
 101
 102 static struct i2c_driver thmc50_driver = {
 103         .class = I2C_CLASS_HWMON,
 104         .driver = {
 105                 .name = "thmc50",
 106         },
 107         .probe = thmc50_probe,
 108         .remove = thmc50_remove,
 109         .id_table = thmc50_id,
 110         .detect = thmc50_detect,
 111         .address_list = normal_i2c,
 112 };
 113
 114 static ssize_t show_analog_out(struct device *dev,
 115                                struct device_attribute *attr, char *buf)
 116 {
 117         struct thmc50_data *data = thmc50_update_device(dev);
 118         return sprintf(buf, "%d\n", data->analog_out);
 119 }
 120
 121 static ssize_t set_analog_out(struct device *dev,
 122                               struct device_attribute *attr,
 123                               const char *buf, size_t count)
 124 {
 125         struct i2c_client *client = to_i2c_client(dev);
 126         struct thmc50_data *data = i2c_get_clientdata(client);
 127         int config;
 128         unsigned long tmp;
 129         int err;
 130
 131         err = kstrtoul(buf, 10, &tmp);
 132         if (err)
 133                 return err;
 134
 135         mutex_lock(&data->update_lock);
 136         data->analog_out = SENSORS_LIMIT(tmp, 0, 255);
 137         i2c_smbus_write_byte_data(client, THMC50_REG_ANALOG_OUT,
 138                                   data->analog_out);
 139
 140         config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 141         if (data->analog_out == 0)
 142                 config &= ~THMC50_REG_CONF_nFANOFF;
 143         else
 144                 config |= THMC50_REG_CONF_nFANOFF;
 145         i2c_smbus_write_byte_data(client, THMC50_REG_CONF, config);
 146
 147         mutex_unlock(&data->update_lock);
 148         return count;
 149 }
 150
 151 /* There is only one PWM mode = DC */
 152 static ssize_t show_pwm_mode(struct device *dev, struct device_attribute *attr,
 153                              char *buf)
 154 {
 155         return sprintf(buf, "0\n");
 156 }
 157
 158 /* Temperatures */
 159 static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
 160                          char *buf)
 161 {
 162         int nr = to_sensor_dev_attr(attr)->index;
 163         struct thmc50_data *data = thmc50_update_device(dev);
 164         return sprintf(buf, "%d\n", data->temp_input[nr] * 1000);
 165 }
 166
 167 static ssize_t show_temp_min(struct device *dev, struct device_attribute *attr,
 168                              char *buf)
 169 {
 170         int nr = to_sensor_dev_attr(attr)->index;
 171         struct thmc50_data *data = thmc50_update_device(dev);
 172         return sprintf(buf, "%d\n", data->temp_min[nr] * 1000);
 173 }
 174
 175 static ssize_t set_temp_min(struct device *dev, struct device_attribute *attr,
 176                             const char *buf, size_t count)
 177 {
 178         int nr = to_sensor_dev_attr(attr)->index;
 179         struct i2c_client *client = to_i2c_client(dev);
 180         struct thmc50_data *data = i2c_get_clientdata(client);
 181         long val;
 182         int err;
 183
 184         err = kstrtol(buf, 10, &val);
 185         if (err)
 186                 return err;
 187
 188         mutex_lock(&data->update_lock);
 189         data->temp_min[nr] = SENSORS_LIMIT(val / 1000, -128, 127);
 190         i2c_smbus_write_byte_data(client, THMC50_REG_TEMP_MIN[nr],
 191                                   data->temp_min[nr]);
 192         mutex_unlock(&data->update_lock);
 193         return count;
 194 }
 195
 196 static ssize_t show_temp_max(struct device *dev, struct device_attribute *attr,
 197                              char *buf)
 198 {
 199         int nr = to_sensor_dev_attr(attr)->index;
 200         struct thmc50_data *data = thmc50_update_device(dev);
 201         return sprintf(buf, "%d\n", data->temp_max[nr] * 1000);
 202 }
 203
 204 static ssize_t set_temp_max(struct device *dev, struct device_attribute *attr,
 205                             const char *buf, size_t count)
 206 {
 207         int nr = to_sensor_dev_attr(attr)->index;
 208         struct i2c_client *client = to_i2c_client(dev);
 209         struct thmc50_data *data = i2c_get_clientdata(client);
 210         long val;
 211         int err;
 212
 213         err = kstrtol(buf, 10, &val);
 214         if (err)
 215                 return err;
 216
 217         mutex_lock(&data->update_lock);
 218         data->temp_max[nr] = SENSORS_LIMIT(val / 1000, -128, 127);
 219         i2c_smbus_write_byte_data(client, THMC50_REG_TEMP_MAX[nr],
 220                                   data->temp_max[nr]);
 221         mutex_unlock(&data->update_lock);
 222         return count;
 223 }
 224
 225 static ssize_t show_temp_critical(struct device *dev,
 226                                   struct device_attribute *attr,
 227                                   char *buf)
 228 {
 229         int nr = to_sensor_dev_attr(attr)->index;
 230         struct thmc50_data *data = thmc50_update_device(dev);
 231         return sprintf(buf, "%d\n", data->temp_critical[nr] * 1000);
 232 }
 233
 234 static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
 235                           char *buf)
 236 {
 237         int index = to_sensor_dev_attr(attr)->index;
 238         struct thmc50_data *data = thmc50_update_device(dev);
 239
 240         return sprintf(buf, "%u\n", (data->alarms >> index) & 1);
 241 }
 242
 243 #define temp_reg(offset)                                                \
 244 static SENSOR_DEVICE_ATTR(temp##offset##_input, S_IRUGO, show_temp,     \
 245                         NULL, offset - 1);                              \
 246 static SENSOR_DEVICE_ATTR(temp##offset##_min, S_IRUGO | S_IWUSR,        \
 247                         show_temp_min, set_temp_min, offset - 1);       \
 248 static SENSOR_DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR,        \
 249                         show_temp_max, set_temp_max, offset - 1);       \
 250 static SENSOR_DEVICE_ATTR(temp##offset##_crit, S_IRUGO,                 \
 251                         show_temp_critical, NULL, offset - 1);
 252
 253 temp_reg(1);
 254 temp_reg(2);
 255 temp_reg(3);
 256
 257 static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 0);
 258 static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 5);
 259 static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 1);
 260 static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 7);
 261 static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 2);
 262
 263 static SENSOR_DEVICE_ATTR(pwm1, S_IRUGO | S_IWUSR, show_analog_out,
 264                           set_analog_out, 0);
 265 static SENSOR_DEVICE_ATTR(pwm1_mode, S_IRUGO, show_pwm_mode, NULL, 0);
 266
 267 static struct attribute *thmc50_attributes[] = {
 268         &sensor_dev_attr_temp1_max.dev_attr.attr,
 269         &sensor_dev_attr_temp1_min.dev_attr.attr,
 270         &sensor_dev_attr_temp1_input.dev_attr.attr,
 271         &sensor_dev_attr_temp1_crit.dev_attr.attr,
 272         &sensor_dev_attr_temp1_alarm.dev_attr.attr,
 273         &sensor_dev_attr_temp2_max.dev_attr.attr,
 274         &sensor_dev_attr_temp2_min.dev_attr.attr,
 275         &sensor_dev_attr_temp2_input.dev_attr.attr,
 276         &sensor_dev_attr_temp2_crit.dev_attr.attr,
 277         &sensor_dev_attr_temp2_alarm.dev_attr.attr,
 278         &sensor_dev_attr_temp2_fault.dev_attr.attr,
 279         &sensor_dev_attr_pwm1.dev_attr.attr,
 280         &sensor_dev_attr_pwm1_mode.dev_attr.attr,
 281         NULL
 282 };
 283
 284 static const struct attribute_group thmc50_group = {
 285         .attrs = thmc50_attributes,
 286 };
 287
 288 /* for ADM1022 3rd temperature mode */
 289 static struct attribute *temp3_attributes[] = {
 290         &sensor_dev_attr_temp3_max.dev_attr.attr,
 291         &sensor_dev_attr_temp3_min.dev_attr.attr,
 292         &sensor_dev_attr_temp3_input.dev_attr.attr,
 293         &sensor_dev_attr_temp3_crit.dev_attr.attr,
 294         &sensor_dev_attr_temp3_alarm.dev_attr.attr,
 295         &sensor_dev_attr_temp3_fault.dev_attr.attr,
 296         NULL
 297 };
 298
 299 static const struct attribute_group temp3_group = {
 300         .attrs = temp3_attributes,
 301 };
 302
 303 /* Return 0 if detection is successful, -ENODEV otherwise */
 304 static int thmc50_detect(struct i2c_client *client,
 305                          struct i2c_board_info *info)
 306 {
 307         unsigned company;
 308         unsigned revision;
 309         unsigned config;
 310         struct i2c_adapter *adapter = client->adapter;
 311         const char *type_name;
 312
 313         if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
 314                 pr_debug("thmc50: detect failed, "
 315                          "smbus byte data not supported!\n");
 316                 return -ENODEV;
 317         }
 318
 319         pr_debug("thmc50: Probing for THMC50 at 0x%2X on bus %d\n",
 320                  client->addr, i2c_adapter_id(client->adapter));
 321
 322         company = i2c_smbus_read_byte_data(client, THMC50_REG_COMPANY_ID);
 323         revision = i2c_smbus_read_byte_data(client, THMC50_REG_DIE_CODE);
 324         config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 325         if (revision < 0xc0 || (config & 0x10))
 326                 return -ENODEV;
 327
 328         if (company == 0x41) {
 329                 int id = i2c_adapter_id(client->adapter);
 330                 int i;
 331
 332                 type_name = "adm1022";
 333                 for (i = 0; i + 1 < adm1022_temp3_num; i += 2)
 334                         if (adm1022_temp3[i] == id &&
 335                             adm1022_temp3[i + 1] == client->addr) {
 336                                 /* enable 2nd remote temp */
 337                                 config |= (1 << 7);
 338                                 i2c_smbus_write_byte_data(client,
 339                                                           THMC50_REG_CONF,
 340                                                           config);
 341                                 break;
 342                         }
 343         } else if (company == 0x49) {
 344                 type_name = "thmc50";
 345         } else {
 346                 pr_debug("thmc50: Detection of THMC50/ADM1022 failed\n");
 347                 return -ENODEV;
 348         }
 349
 350         pr_debug("thmc50: Detected %s (version %x, revision %x)\n",
 351                  type_name, (revision >> 4) - 0xc, revision & 0xf);
 352
 353         strlcpy(info->type, type_name, I2C_NAME_SIZE);
 354
 355         return 0;
 356 }
 357
 358 static int thmc50_probe(struct i2c_client *client,
 359                         const struct i2c_device_id *id)
 360 {
 361         struct thmc50_data *data;
 362         int err;
 363
 364         data = kzalloc(sizeof(struct thmc50_data), GFP_KERNEL);
 365         if (!data) {
 366                 pr_debug("thmc50: detect failed, kzalloc failed!\n");
 367                 err = -ENOMEM;
 368                 goto exit;
 369         }
 370
 371         i2c_set_clientdata(client, data);
 372         data->type = id->driver_data;
 373         mutex_init(&data->update_lock);
 374
 375         thmc50_init_client(client);
 376
 377         /* Register sysfs hooks */
 378         err = sysfs_create_group(&client->dev.kobj, &thmc50_group);
 379         if (err)
 380                 goto exit_free;
 381
 382         /* Register ADM1022 sysfs hooks */
 383         if (data->has_temp3) {
 384                 err = sysfs_create_group(&client->dev.kobj, &temp3_group);
 385                 if (err)
 386                         goto exit_remove_sysfs_thmc50;
 387         }
 388
 389         /* Register a new directory entry with module sensors */
 390         data->hwmon_dev = hwmon_device_register(&client->dev);
 391         if (IS_ERR(data->hwmon_dev)) {
 392                 err = PTR_ERR(data->hwmon_dev);
 393                 goto exit_remove_sysfs;
 394         }
 395
 396         return 0;
 397
 398 exit_remove_sysfs:
 399         if (data->has_temp3)
 400                 sysfs_remove_group(&client->dev.kobj, &temp3_group);
 401 exit_remove_sysfs_thmc50:
 402         sysfs_remove_group(&client->dev.kobj, &thmc50_group);
 403 exit_free:
 404         kfree(data);
 405 exit:
 406         return err;
 407 }
 408
 409 static int thmc50_remove(struct i2c_client *client)
 410 {
 411         struct thmc50_data *data = i2c_get_clientdata(client);
 412
 413         hwmon_device_unregister(data->hwmon_dev);
 414         sysfs_remove_group(&client->dev.kobj, &thmc50_group);
 415         if (data->has_temp3)
 416                 sysfs_remove_group(&client->dev.kobj, &temp3_group);
 417
 418         kfree(data);
 419
 420         return 0;
 421 }
 422
 423 static void thmc50_init_client(struct i2c_client *client)
 424 {
 425         struct thmc50_data *data = i2c_get_clientdata(client);
 426         int config;
 427
 428         data->analog_out = i2c_smbus_read_byte_data(client,
 429                                                     THMC50_REG_ANALOG_OUT);
 430         /* set up to at least 1 */
 431         if (data->analog_out == 0) {
 432                 data->analog_out = 1;
 433                 i2c_smbus_write_byte_data(client, THMC50_REG_ANALOG_OUT,
 434                                           data->analog_out);
 435         }
 436         config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 437         config |= 0x1;  /* start the chip if it is in standby mode */
 438         if (data->type == adm1022 && (config & (1 << 7)))
 439                 data->has_temp3 = 1;
 440         i2c_smbus_write_byte_data(client, THMC50_REG_CONF, config);
 441 }
 442
 443 static struct thmc50_data *thmc50_update_device(struct device *dev)
 444 {
 445         struct i2c_client *client = to_i2c_client(dev);
 446         struct thmc50_data *data = i2c_get_clientdata(client);
 447         int timeout = HZ / 5 + (data->type == thmc50 ? HZ : 0);
 448
 449         mutex_lock(&data->update_lock);
 450
 451         if (time_after(jiffies, data->last_updated + timeout)
 452             || !data->valid) {
 453
 454                 int temps = data->has_temp3 ? 3 : 2;
 455                 int i;
 456                 int prog = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 457
 458                 prog &= THMC50_REG_CONF_PROGRAMMED;
 459
 460                 for (i = 0; i < temps; i++) {
 461                         data->temp_input[i] = i2c_smbus_read_byte_data(client,
 462                                                 THMC50_REG_TEMP[i]);
 463                         data->temp_max[i] = i2c_smbus_read_byte_data(client,
 464                                                 THMC50_REG_TEMP_MAX[i]);
 465                         data->temp_min[i] = i2c_smbus_read_byte_data(client,
 466                                                 THMC50_REG_TEMP_MIN[i]);
 467                         data->temp_critical[i] =
 468                                 i2c_smbus_read_byte_data(client,
 469                                         prog ? THMC50_REG_TEMP_CRITICAL[i]
 470                                              : THMC50_REG_TEMP_DEFAULT[i]);
 471                 }
 472                 data->analog_out =
 473                     i2c_smbus_read_byte_data(client, THMC50_REG_ANALOG_OUT);
 474                 data->alarms =
 475                     i2c_smbus_read_byte_data(client, THMC50_REG_INTR);
 476                 data->last_updated = jiffies;
 477                 data->valid = 1;
 478         }
 479
 480         mutex_unlock(&data->update_lock);
 481
 482         return data;
 483 }
 484
 485 module_i2c_driver(thmc50_driver);
 486
 487 MODULE_AUTHOR("Krzysztof Helt <krzysztof.h1@wp.pl>");
 488 MODULE_DESCRIPTION("THMC50 driver");