drivers/tty/serial/m32r_sio_reg.h

   1 /*
   2  * m32r_sio_reg.h
   3  *
   4  * Copyright (C) 1992, 1994 by Theodore Ts'o.
   5  * Copyright (C) 2004  Hirokazu Takata <takata at linux-m32r.org>
   6  *
   7  * Redistribution of this file is permitted under the terms of the GNU
   8  * Public License (GPL)
   9  *
  10  * These are the UART port assignments, expressed as offsets from the base
  11  * register.  These assignments should hold for any serial port based on
  12  * a 8250, 16450, or 16550(A).
  13  */
  14
  15 #ifndef _M32R_SIO_REG_H
  16 #define _M32R_SIO_REG_H
  17
  18
  19 #ifdef CONFIG_SERIAL_M32R_PLDSIO
  20
  21 #define SIOCR           0x000
  22 #define SIOMOD0         0x002
  23 #define SIOMOD1         0x004
  24 #define SIOSTS          0x006
  25 #define SIOTRCR         0x008
  26 #define SIOBAUR         0x00a
  27 // #define SIORBAUR     0x018
  28 #define SIOTXB          0x00c
  29 #define SIORXB          0x00e
  30
  31 #define UART_RX         ((unsigned long) PLD_ESIO0RXB)
  32                                 /* In:  Receive buffer (DLAB=0) */
  33 #define UART_TX         ((unsigned long) PLD_ESIO0TXB)
  34                                 /* Out: Transmit buffer (DLAB=0) */
  35 #define UART_DLL        0       /* Out: Divisor Latch Low (DLAB=1) */
  36 #define UART_TRG        0       /* (LCR=BF) FCTR bit 7 selects Rx or Tx
  37                                  * In: Fifo count
  38                                  * Out: Fifo custom trigger levels
  39                                  * XR16C85x only */
  40
  41 #define UART_DLM        0       /* Out: Divisor Latch High (DLAB=1) */
  42 #define UART_IER        ((unsigned long) PLD_ESIO0INTCR)
  43                                 /* Out: Interrupt Enable Register */
  44 #define UART_FCTR       0       /* (LCR=BF) Feature Control Register
  45                                  * XR16C85x only */
  46
  47 #define UART_IIR        0       /* In:  Interrupt ID Register */
  48 #define UART_FCR        0       /* Out: FIFO Control Register */
  49 #define UART_EFR        0       /* I/O: Extended Features Register */
  50                                 /* (DLAB=1, 16C660 only) */
  51
  52 #define UART_LCR        0       /* Out: Line Control Register */
  53 #define UART_MCR        0       /* Out: Modem Control Register */
  54 #define UART_LSR        ((unsigned long) PLD_ESIO0STS)
  55                                 /* In:  Line Status Register */
  56 #define UART_MSR        0       /* In:  Modem Status Register */
  57 #define UART_SCR        0       /* I/O: Scratch Register */
  58 #define UART_EMSR       0       /* (LCR=BF) Extended Mode Select Register
  59                                  * FCTR bit 6 selects SCR or EMSR
  60                                  * XR16c85x only */
  61
  62 #else /* not CONFIG_SERIAL_M32R_PLDSIO */
  63
  64 #define SIOCR           0x000
  65 #define SIOMOD0         0x004
  66 #define SIOMOD1         0x008
  67 #define SIOSTS          0x00c
  68 #define SIOTRCR         0x010
  69 #define SIOBAUR         0x014
  70 #define SIORBAUR        0x018
  71 #define SIOTXB          0x01c
  72 #define SIORXB          0x020
  73
  74 #define UART_RX         M32R_SIO0_RXB_PORTL     /* In:  Receive buffer (DLAB=0) */
  75 #define UART_TX         M32R_SIO0_TXB_PORTL     /* Out: Transmit buffer (DLAB=0) */
  76 #define UART_DLL        0       /* Out: Divisor Latch Low (DLAB=1) */
  77 #define UART_TRG        0       /* (LCR=BF) FCTR bit 7 selects Rx or Tx
  78                                  * In: Fifo count
  79                                  * Out: Fifo custom trigger levels
  80                                  * XR16C85x only */
  81
  82 #define UART_DLM        0       /* Out: Divisor Latch High (DLAB=1) */
  83 #define UART_IER        M32R_SIO0_TRCR_PORTL    /* Out: Interrupt Enable Register */
  84 #define UART_FCTR       0       /* (LCR=BF) Feature Control Register
  85                                  * XR16C85x only */
  86
  87 #define UART_IIR        0       /* In:  Interrupt ID Register */
  88 #define UART_FCR        0       /* Out: FIFO Control Register */
  89 #define UART_EFR        0       /* I/O: Extended Features Register */
  90                                 /* (DLAB=1, 16C660 only) */
  91
  92 #define UART_LCR        0       /* Out: Line Control Register */
  93 #define UART_MCR        0       /* Out: Modem Control Register */
  94 #define UART_LSR        M32R_SIO0_STS_PORTL     /* In:  Line Status Register */
  95 #define UART_MSR        0       /* In:  Modem Status Register */
  96 #define UART_SCR        0       /* I/O: Scratch Register */
  97 #define UART_EMSR       0       /* (LCR=BF) Extended Mode Select Register
  98                                  * FCTR bit 6 selects SCR or EMSR
  99                                  * XR16c85x only */
 100
 101 #endif /* CONFIG_SERIAL_M32R_PLDSIO */
 102
 103 #define UART_EMPTY      (UART_LSR_TEMT | UART_LSR_THRE)
 104
 105 /*
 106  * These are the definitions for the Line Control Register
 107  *
 108  * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
 109  * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
 110  */
 111 #define UART_LCR_DLAB   0x80    /* Divisor latch access bit */
 112 #define UART_LCR_SBC    0x40    /* Set break control */
 113 #define UART_LCR_SPAR   0x20    /* Stick parity (?) */
 114 #define UART_LCR_EPAR   0x10    /* Even parity select */
 115 #define UART_LCR_PARITY 0x08    /* Parity Enable */
 116 #define UART_LCR_STOP   0x04    /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
 117 #define UART_LCR_WLEN5  0x00    /* Wordlength: 5 bits */
 118 #define UART_LCR_WLEN6  0x01    /* Wordlength: 6 bits */
 119 #define UART_LCR_WLEN7  0x02    /* Wordlength: 7 bits */
 120 #define UART_LCR_WLEN8  0x03    /* Wordlength: 8 bits */
 121
 122 /*
 123  * These are the definitions for the Line Status Register
 124  */
 125 #define UART_LSR_TEMT   0x02    /* Transmitter empty */
 126 #define UART_LSR_THRE   0x01    /* Transmit-hold-register empty */
 127 #define UART_LSR_BI     0x00    /* Break interrupt indicator */
 128 #define UART_LSR_FE     0x80    /* Frame error indicator */
 129 #define UART_LSR_PE     0x40    /* Parity error indicator */
 130 #define UART_LSR_OE     0x20    /* Overrun error indicator */
 131 #define UART_LSR_DR     0x04    /* Receiver data ready */
 132
 133 /*
 134  * These are the definitions for the Interrupt Identification Register
 135  */
 136 #define UART_IIR_NO_INT 0x01    /* No interrupts pending */
 137 #define UART_IIR_ID     0x06    /* Mask for the interrupt ID */
 138
 139 #define UART_IIR_MSI    0x00    /* Modem status interrupt */
 140 #define UART_IIR_THRI   0x02    /* Transmitter holding register empty */
 141 #define UART_IIR_RDI    0x04    /* Receiver data interrupt */
 142 #define UART_IIR_RLSI   0x06    /* Receiver line status interrupt */
 143
 144 /*
 145  * These are the definitions for the Interrupt Enable Register
 146  */
 147 #define UART_IER_MSI    0x00    /* Enable Modem status interrupt */
 148 #define UART_IER_RLSI   0x08    /* Enable receiver line status interrupt */
 149 #define UART_IER_THRI   0x03    /* Enable Transmitter holding register int. */
 150 #define UART_IER_RDI    0x04    /* Enable receiver data interrupt */
 151
 152 #endif /* _M32R_SIO_REG_H */