arm64: dts: Revert "specify console via command line"
[linux/fpc-iii.git] / arch / arm / mach-omap1 / usb.c
blobd8e9bbda8f7bdd6ec6b4671c3b2ef11fed18793f
1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * Platform level USB initialization for FS USB OTG controller on omap1
5 * Copyright (C) 2004 Texas Instruments, Inc.
6 */
8 #include <linux/module.h>
9 #include <linux/kernel.h>
10 #include <linux/init.h>
11 #include <linux/platform_device.h>
12 #include <linux/io.h>
14 #include <asm/irq.h>
16 #include <mach/mux.h>
18 #include <mach/usb.h>
20 #include "common.h"
22 /* These routines should handle the standard chip-specific modes
23 * for usb0/1/2 ports, covering basic mux and transceiver setup.
25 * Some board-*.c files will need to set up additional mux options,
26 * like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
29 /* TESTED ON:
30 * - 1611B H2 (with usb1 mini-AB) using standard Mini-B or OTG cables
31 * - 5912 OSK OHCI (with usb0 standard-A), standard A-to-B cables
32 * - 5912 OSK UDC, with *nonstandard* A-to-A cable
33 * - 1510 Innovator UDC with bundled usb0 cable
34 * - 1510 Innovator OHCI with bundled usb1/usb2 cable
35 * - 1510 Innovator OHCI with custom usb0 cable, feeding 5V VBUS
36 * - 1710 custom development board using alternate pin group
37 * - 1710 H3 (with usb1 mini-AB) using standard Mini-B or OTG cables
40 #define INT_USB_IRQ_GEN IH2_BASE + 20
41 #define INT_USB_IRQ_NISO IH2_BASE + 30
42 #define INT_USB_IRQ_ISO IH2_BASE + 29
43 #define INT_USB_IRQ_HGEN INT_USB_HHC_1
44 #define INT_USB_IRQ_OTG IH2_BASE + 8
46 #ifdef CONFIG_ARCH_OMAP_OTG
48 static void __init
49 omap_otg_init(struct omap_usb_config *config)
51 u32 syscon;
52 int alt_pingroup = 0;
53 u16 w;
55 /* NOTE: no bus or clock setup (yet?) */
57 syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
58 if (!(syscon & OTG_RESET_DONE))
59 pr_debug("USB resets not complete?\n");
61 //omap_writew(0, OTG_IRQ_EN);
63 /* pin muxing and transceiver pinouts */
64 if (config->pins[0] > 2) /* alt pingroup 2 */
65 alt_pingroup = 1;
66 syscon |= config->usb0_init(config->pins[0], is_usb0_device(config));
67 syscon |= config->usb1_init(config->pins[1]);
68 syscon |= config->usb2_init(config->pins[2], alt_pingroup);
69 pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
70 omap_writel(syscon, OTG_SYSCON_1);
72 syscon = config->hmc_mode;
73 syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
74 #ifdef CONFIG_USB_OTG
75 if (config->otg)
76 syscon |= OTG_EN;
77 #endif
78 pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
79 omap_readl(USB_TRANSCEIVER_CTRL));
80 pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
81 omap_writel(syscon, OTG_SYSCON_2);
83 printk("USB: hmc %d", config->hmc_mode);
84 if (!alt_pingroup)
85 pr_cont(", usb2 alt %d wires", config->pins[2]);
86 else if (config->pins[0])
87 pr_cont(", usb0 %d wires%s", config->pins[0],
88 is_usb0_device(config) ? " (dev)" : "");
89 if (config->pins[1])
90 pr_cont(", usb1 %d wires", config->pins[1]);
91 if (!alt_pingroup && config->pins[2])
92 pr_cont(", usb2 %d wires", config->pins[2]);
93 if (config->otg)
94 pr_cont(", Mini-AB on usb%d", config->otg - 1);
95 pr_cont("\n");
97 /* leave USB clocks/controllers off until needed */
98 w = omap_readw(ULPD_SOFT_REQ);
99 w &= ~SOFT_USB_CLK_REQ;
100 omap_writew(w, ULPD_SOFT_REQ);
102 w = omap_readw(ULPD_CLOCK_CTRL);
103 w &= ~USB_MCLK_EN;
104 w |= DIS_USB_PVCI_CLK;
105 omap_writew(w, ULPD_CLOCK_CTRL);
107 syscon = omap_readl(OTG_SYSCON_1);
108 syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
110 #if IS_ENABLED(CONFIG_USB_OMAP)
111 if (config->otg || config->register_dev) {
112 struct platform_device *udc_device = config->udc_device;
113 int status;
115 syscon &= ~DEV_IDLE_EN;
116 udc_device->dev.platform_data = config;
117 status = platform_device_register(udc_device);
118 if (status)
119 pr_debug("can't register UDC device, %d\n", status);
121 #endif
123 #if IS_ENABLED(CONFIG_USB_OHCI_HCD)
124 if (config->otg || config->register_host) {
125 struct platform_device *ohci_device = config->ohci_device;
126 int status;
128 syscon &= ~HST_IDLE_EN;
129 ohci_device->dev.platform_data = config;
130 status = platform_device_register(ohci_device);
131 if (status)
132 pr_debug("can't register OHCI device, %d\n", status);
134 #endif
136 #ifdef CONFIG_USB_OTG
137 if (config->otg) {
138 struct platform_device *otg_device = config->otg_device;
139 int status;
141 syscon &= ~OTG_IDLE_EN;
142 otg_device->dev.platform_data = config;
143 status = platform_device_register(otg_device);
144 if (status)
145 pr_debug("can't register OTG device, %d\n", status);
147 #endif
148 pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
149 omap_writel(syscon, OTG_SYSCON_1);
152 #else
153 static void omap_otg_init(struct omap_usb_config *config) {}
154 #endif
156 #if IS_ENABLED(CONFIG_USB_OMAP)
158 static struct resource udc_resources[] = {
159 /* order is significant! */
160 { /* registers */
161 .start = UDC_BASE,
162 .end = UDC_BASE + 0xff,
163 .flags = IORESOURCE_MEM,
164 }, { /* general IRQ */
165 .start = INT_USB_IRQ_GEN,
166 .flags = IORESOURCE_IRQ,
167 }, { /* PIO IRQ */
168 .start = INT_USB_IRQ_NISO,
169 .flags = IORESOURCE_IRQ,
170 }, { /* SOF IRQ */
171 .start = INT_USB_IRQ_ISO,
172 .flags = IORESOURCE_IRQ,
176 static u64 udc_dmamask = ~(u32)0;
178 static struct platform_device udc_device = {
179 .name = "omap_udc",
180 .id = -1,
181 .dev = {
182 .dma_mask = &udc_dmamask,
183 .coherent_dma_mask = 0xffffffff,
185 .num_resources = ARRAY_SIZE(udc_resources),
186 .resource = udc_resources,
189 static inline void udc_device_init(struct omap_usb_config *pdata)
191 /* IRQ numbers for omap7xx */
192 if(cpu_is_omap7xx()) {
193 udc_resources[1].start = INT_7XX_USB_GENI;
194 udc_resources[2].start = INT_7XX_USB_NON_ISO;
195 udc_resources[3].start = INT_7XX_USB_ISO;
197 pdata->udc_device = &udc_device;
200 #else
202 static inline void udc_device_init(struct omap_usb_config *pdata)
206 #endif
208 #if IS_ENABLED(CONFIG_USB_OHCI_HCD)
210 /* The dmamask must be set for OHCI to work */
211 static u64 ohci_dmamask = ~(u32)0;
213 static struct resource ohci_resources[] = {
215 .start = OMAP_OHCI_BASE,
216 .end = OMAP_OHCI_BASE + 0xff,
217 .flags = IORESOURCE_MEM,
220 .start = INT_USB_IRQ_HGEN,
221 .flags = IORESOURCE_IRQ,
225 static struct platform_device ohci_device = {
226 .name = "ohci",
227 .id = -1,
228 .dev = {
229 .dma_mask = &ohci_dmamask,
230 .coherent_dma_mask = 0xffffffff,
232 .num_resources = ARRAY_SIZE(ohci_resources),
233 .resource = ohci_resources,
236 static inline void ohci_device_init(struct omap_usb_config *pdata)
238 if (cpu_is_omap7xx())
239 ohci_resources[1].start = INT_7XX_USB_HHC_1;
240 pdata->ohci_device = &ohci_device;
241 pdata->ocpi_enable = &ocpi_enable;
244 #else
246 static inline void ohci_device_init(struct omap_usb_config *pdata)
250 #endif
252 #if defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)
254 static struct resource otg_resources[] = {
255 /* order is significant! */
257 .start = OTG_BASE,
258 .end = OTG_BASE + 0xff,
259 .flags = IORESOURCE_MEM,
260 }, {
261 .start = INT_USB_IRQ_OTG,
262 .flags = IORESOURCE_IRQ,
266 static struct platform_device otg_device = {
267 .name = "omap_otg",
268 .id = -1,
269 .num_resources = ARRAY_SIZE(otg_resources),
270 .resource = otg_resources,
273 static inline void otg_device_init(struct omap_usb_config *pdata)
275 if (cpu_is_omap7xx())
276 otg_resources[1].start = INT_7XX_USB_OTG;
277 pdata->otg_device = &otg_device;
280 #else
282 static inline void otg_device_init(struct omap_usb_config *pdata)
286 #endif
288 static u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
290 u32 syscon1 = 0;
292 if (nwires == 0) {
293 if (!cpu_is_omap15xx()) {
294 u32 l;
296 /* pulldown D+/D- */
297 l = omap_readl(USB_TRANSCEIVER_CTRL);
298 l &= ~(3 << 1);
299 omap_writel(l, USB_TRANSCEIVER_CTRL);
301 return 0;
304 if (is_device) {
305 if (cpu_is_omap7xx()) {
306 omap_cfg_reg(AA17_7XX_USB_DM);
307 omap_cfg_reg(W16_7XX_USB_PU_EN);
308 omap_cfg_reg(W17_7XX_USB_VBUSI);
309 omap_cfg_reg(W18_7XX_USB_DMCK_OUT);
310 omap_cfg_reg(W19_7XX_USB_DCRST);
311 } else
312 omap_cfg_reg(W4_USB_PUEN);
315 if (nwires == 2) {
316 u32 l;
318 // omap_cfg_reg(P9_USB_DP);
319 // omap_cfg_reg(R8_USB_DM);
321 if (cpu_is_omap15xx()) {
322 /* This works on 1510-Innovator */
323 return 0;
326 /* NOTES:
327 * - peripheral should configure VBUS detection!
328 * - only peripherals may use the internal D+/D- pulldowns
329 * - OTG support on this port not yet written
332 /* Don't do this for omap7xx -- it causes USB to not work correctly */
333 if (!cpu_is_omap7xx()) {
334 l = omap_readl(USB_TRANSCEIVER_CTRL);
335 l &= ~(7 << 4);
336 if (!is_device)
337 l |= (3 << 1);
338 omap_writel(l, USB_TRANSCEIVER_CTRL);
341 return 3 << 16;
344 /* alternate pin config, external transceiver */
345 if (cpu_is_omap15xx()) {
346 printk(KERN_ERR "no usb0 alt pin config on 15xx\n");
347 return 0;
350 omap_cfg_reg(V6_USB0_TXD);
351 omap_cfg_reg(W9_USB0_TXEN);
352 omap_cfg_reg(W5_USB0_SE0);
353 if (nwires != 3)
354 omap_cfg_reg(Y5_USB0_RCV);
356 /* NOTE: SPEED and SUSP aren't configured here. OTG hosts
357 * may be able to use I2C requests to set those bits along
358 * with VBUS switching and overcurrent detection.
361 if (nwires != 6) {
362 u32 l;
364 l = omap_readl(USB_TRANSCEIVER_CTRL);
365 l &= ~CONF_USB2_UNI_R;
366 omap_writel(l, USB_TRANSCEIVER_CTRL);
369 switch (nwires) {
370 case 3:
371 syscon1 = 2;
372 break;
373 case 4:
374 syscon1 = 1;
375 break;
376 case 6:
377 syscon1 = 3;
379 u32 l;
381 omap_cfg_reg(AA9_USB0_VP);
382 omap_cfg_reg(R9_USB0_VM);
383 l = omap_readl(USB_TRANSCEIVER_CTRL);
384 l |= CONF_USB2_UNI_R;
385 omap_writel(l, USB_TRANSCEIVER_CTRL);
387 break;
388 default:
389 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
390 0, nwires);
393 return syscon1 << 16;
396 static u32 __init omap1_usb1_init(unsigned nwires)
398 u32 syscon1 = 0;
400 if (!cpu_is_omap15xx() && nwires != 6) {
401 u32 l;
403 l = omap_readl(USB_TRANSCEIVER_CTRL);
404 l &= ~CONF_USB1_UNI_R;
405 omap_writel(l, USB_TRANSCEIVER_CTRL);
407 if (nwires == 0)
408 return 0;
410 /* external transceiver */
411 omap_cfg_reg(USB1_TXD);
412 omap_cfg_reg(USB1_TXEN);
413 if (nwires != 3)
414 omap_cfg_reg(USB1_RCV);
416 if (cpu_is_omap15xx()) {
417 omap_cfg_reg(USB1_SEO);
418 omap_cfg_reg(USB1_SPEED);
419 // SUSP
420 } else if (cpu_is_omap1610() || cpu_is_omap5912()) {
421 omap_cfg_reg(W13_1610_USB1_SE0);
422 omap_cfg_reg(R13_1610_USB1_SPEED);
423 // SUSP
424 } else if (cpu_is_omap1710()) {
425 omap_cfg_reg(R13_1710_USB1_SE0);
426 // SUSP
427 } else {
428 pr_debug("usb%d cpu unrecognized\n", 1);
429 return 0;
432 switch (nwires) {
433 case 2:
434 goto bad;
435 case 3:
436 syscon1 = 2;
437 break;
438 case 4:
439 syscon1 = 1;
440 break;
441 case 6:
442 syscon1 = 3;
443 omap_cfg_reg(USB1_VP);
444 omap_cfg_reg(USB1_VM);
445 if (!cpu_is_omap15xx()) {
446 u32 l;
448 l = omap_readl(USB_TRANSCEIVER_CTRL);
449 l |= CONF_USB1_UNI_R;
450 omap_writel(l, USB_TRANSCEIVER_CTRL);
452 break;
453 default:
454 bad:
455 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
456 1, nwires);
459 return syscon1 << 20;
462 static u32 __init omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
464 u32 syscon1 = 0;
466 /* NOTE omap1 erratum: must leave USB2_UNI_R set if usb0 in use */
467 if (alt_pingroup || nwires == 0)
468 return 0;
470 if (!cpu_is_omap15xx() && nwires != 6) {
471 u32 l;
473 l = omap_readl(USB_TRANSCEIVER_CTRL);
474 l &= ~CONF_USB2_UNI_R;
475 omap_writel(l, USB_TRANSCEIVER_CTRL);
478 /* external transceiver */
479 if (cpu_is_omap15xx()) {
480 omap_cfg_reg(USB2_TXD);
481 omap_cfg_reg(USB2_TXEN);
482 omap_cfg_reg(USB2_SEO);
483 if (nwires != 3)
484 omap_cfg_reg(USB2_RCV);
485 /* there is no USB2_SPEED */
486 } else if (cpu_is_omap16xx()) {
487 omap_cfg_reg(V6_USB2_TXD);
488 omap_cfg_reg(W9_USB2_TXEN);
489 omap_cfg_reg(W5_USB2_SE0);
490 if (nwires != 3)
491 omap_cfg_reg(Y5_USB2_RCV);
492 // FIXME omap_cfg_reg(USB2_SPEED);
493 } else {
494 pr_debug("usb%d cpu unrecognized\n", 1);
495 return 0;
498 // omap_cfg_reg(USB2_SUSP);
500 switch (nwires) {
501 case 2:
502 goto bad;
503 case 3:
504 syscon1 = 2;
505 break;
506 case 4:
507 syscon1 = 1;
508 break;
509 case 5:
510 goto bad;
511 case 6:
512 syscon1 = 3;
513 if (cpu_is_omap15xx()) {
514 omap_cfg_reg(USB2_VP);
515 omap_cfg_reg(USB2_VM);
516 } else {
517 u32 l;
519 omap_cfg_reg(AA9_USB2_VP);
520 omap_cfg_reg(R9_USB2_VM);
521 l = omap_readl(USB_TRANSCEIVER_CTRL);
522 l |= CONF_USB2_UNI_R;
523 omap_writel(l, USB_TRANSCEIVER_CTRL);
525 break;
526 default:
527 bad:
528 printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
529 2, nwires);
532 return syscon1 << 24;
535 #ifdef CONFIG_ARCH_OMAP15XX
537 /* ULPD_DPLL_CTRL */
538 #define DPLL_IOB (1 << 13)
539 #define DPLL_PLL_ENABLE (1 << 4)
540 #define DPLL_LOCK (1 << 0)
542 /* ULPD_APLL_CTRL */
543 #define APLL_NDPLL_SWITCH (1 << 0)
545 static void __init omap_1510_usb_init(struct omap_usb_config *config)
547 unsigned int val;
548 u16 w;
550 config->usb0_init(config->pins[0], is_usb0_device(config));
551 config->usb1_init(config->pins[1]);
552 config->usb2_init(config->pins[2], 0);
554 val = omap_readl(MOD_CONF_CTRL_0) & ~(0x3f << 1);
555 val |= (config->hmc_mode << 1);
556 omap_writel(val, MOD_CONF_CTRL_0);
558 printk("USB: hmc %d", config->hmc_mode);
559 if (config->pins[0])
560 pr_cont(", usb0 %d wires%s", config->pins[0],
561 is_usb0_device(config) ? " (dev)" : "");
562 if (config->pins[1])
563 pr_cont(", usb1 %d wires", config->pins[1]);
564 if (config->pins[2])
565 pr_cont(", usb2 %d wires", config->pins[2]);
566 pr_cont("\n");
568 /* use DPLL for 48 MHz function clock */
569 pr_debug("APLL %04x DPLL %04x REQ %04x\n", omap_readw(ULPD_APLL_CTRL),
570 omap_readw(ULPD_DPLL_CTRL), omap_readw(ULPD_SOFT_REQ));
572 w = omap_readw(ULPD_APLL_CTRL);
573 w &= ~APLL_NDPLL_SWITCH;
574 omap_writew(w, ULPD_APLL_CTRL);
576 w = omap_readw(ULPD_DPLL_CTRL);
577 w |= DPLL_IOB | DPLL_PLL_ENABLE;
578 omap_writew(w, ULPD_DPLL_CTRL);
580 w = omap_readw(ULPD_SOFT_REQ);
581 w |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
582 omap_writew(w, ULPD_SOFT_REQ);
584 while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK))
585 cpu_relax();
587 #if IS_ENABLED(CONFIG_USB_OMAP)
588 if (config->register_dev) {
589 int status;
591 udc_device.dev.platform_data = config;
592 status = platform_device_register(&udc_device);
593 if (status)
594 pr_debug("can't register UDC device, %d\n", status);
595 /* udc driver gates 48MHz by D+ pullup */
597 #endif
599 #if IS_ENABLED(CONFIG_USB_OHCI_HCD)
600 if (config->register_host) {
601 int status;
603 ohci_device.dev.platform_data = config;
604 status = platform_device_register(&ohci_device);
605 if (status)
606 pr_debug("can't register OHCI device, %d\n", status);
607 /* hcd explicitly gates 48MHz */
609 #endif
612 #else
613 static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
614 #endif
616 void __init omap1_usb_init(struct omap_usb_config *_pdata)
618 struct omap_usb_config *pdata;
620 pdata = kmemdup(_pdata, sizeof(*pdata), GFP_KERNEL);
621 if (!pdata)
622 return;
624 pdata->usb0_init = omap1_usb0_init;
625 pdata->usb1_init = omap1_usb1_init;
626 pdata->usb2_init = omap1_usb2_init;
627 udc_device_init(pdata);
628 ohci_device_init(pdata);
629 otg_device_init(pdata);
631 if (cpu_is_omap7xx() || cpu_is_omap16xx())
632 omap_otg_init(pdata);
633 else if (cpu_is_omap15xx())
634 omap_1510_usb_init(pdata);
635 else
636 printk(KERN_ERR "USB: No init for your chip yet\n");