arm64: dts: Revert "specify console via command line"
[linux/fpc-iii.git] / arch / arm / mach-omap2 / opp2430_data.c
blobded8b566a23a9ac4a5e050374f0cfb34d7ee89a4
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * opp2430_data.c - old-style "OPP" table for OMAP2430
5 * Copyright (C) 2005-2009 Texas Instruments, Inc.
6 * Copyright (C) 2004-2009 Nokia Corporation
8 * Richard Woodruff <r-woodruff2@ti.com>
10 * The OMAP2 processor can be run at several discrete 'PRCM configurations'.
11 * These configurations are characterized by voltage and speed for clocks.
12 * The device is only validated for certain combinations. One way to express
13 * these combinations is via the 'ratios' which the clocks operate with
14 * respect to each other. These ratio sets are for a given voltage/DPLL
15 * setting. All configurations can be described by a DPLL setting and a ratio.
17 * 2430 differs from 2420 in that there are no more phase synchronizers used.
18 * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs
19 * 2430 (iva2.1, NOdsp, mdm)
21 * XXX Missing voltage data.
22 * XXX Missing 19.2MHz sys_clk rate sets.
24 * THe format described in this file is deprecated. Once a reasonable
25 * OPP API exists, the data in this file should be converted to use it.
27 * This is technically part of the OMAP2xxx clock code.
30 #include <linux/kernel.h>
32 #include "opp2xxx.h"
33 #include "sdrc.h"
34 #include "clock.h"
37 * Key dividers which make up a PRCM set. Ratios for a PRCM are mandated.
38 * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU,
39 * CM_CLKSEL_DSP, CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL,
40 * CM_CLKSEL2_PLL, CM_CLKSEL_MDM
42 * Filling in table based on 2430-SDPs variants available. There are
43 * quite a few more rate combinations which could be defined.
45 * When multiple values are defined the start up will try and choose
46 * the fastest one. If a 'fast' value is defined, then automatically,
47 * the /2 one should be included as it can be used. Generally having
48 * more than one fast set does not make sense, as static timings need
49 * to be changed to change the set. The exception is the bypass
50 * setting which is available for low power bypass.
52 * Note: This table needs to be sorted, fastest to slowest.
54 const struct prcm_config omap2430_rate_table[] = {
55 /* PRCM #4 - ratio2 (ES2.1) - FAST */
56 {S13M, S798M, S399M, R2_CM_CLKSEL_MPU_VAL, /* 399MHz ARM */
57 R2_CM_CLKSEL_DSP_VAL, R2_CM_CLKSEL_GFX_VAL,
58 R2_CM_CLKSEL1_CORE_VAL, M4_CM_CLKSEL1_PLL_13_VAL,
59 MX_CLKSEL2_PLL_2x_VAL, R2_CM_CLKSEL_MDM_VAL,
60 SDRC_RFR_CTRL_133MHz,
61 RATE_IN_243X},
63 /* PRCM #2 - ratio1 (ES2) - FAST */
64 {S13M, S658M, S329M, R1_CM_CLKSEL_MPU_VAL, /* 330MHz ARM */
65 R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
66 R1_CM_CLKSEL1_CORE_VAL, M2_CM_CLKSEL1_PLL_13_VAL,
67 MX_CLKSEL2_PLL_2x_VAL, R1_CM_CLKSEL_MDM_VAL,
68 SDRC_RFR_CTRL_165MHz,
69 RATE_IN_243X},
71 /* PRCM #5a - ratio1 - FAST */
72 {S13M, S532M, S266M, R1_CM_CLKSEL_MPU_VAL, /* 266MHz ARM */
73 R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
74 R1_CM_CLKSEL1_CORE_VAL, M5A_CM_CLKSEL1_PLL_13_VAL,
75 MX_CLKSEL2_PLL_2x_VAL, R1_CM_CLKSEL_MDM_VAL,
76 SDRC_RFR_CTRL_133MHz,
77 RATE_IN_243X},
79 /* PRCM #5b - ratio1 - FAST */
80 {S13M, S400M, S200M, R1_CM_CLKSEL_MPU_VAL, /* 200MHz ARM */
81 R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
82 R1_CM_CLKSEL1_CORE_VAL, M5B_CM_CLKSEL1_PLL_13_VAL,
83 MX_CLKSEL2_PLL_2x_VAL, R1_CM_CLKSEL_MDM_VAL,
84 SDRC_RFR_CTRL_100MHz,
85 RATE_IN_243X},
87 /* PRCM #4 - ratio1 (ES2.1) - SLOW */
88 {S13M, S399M, S199M, R2_CM_CLKSEL_MPU_VAL, /* 200MHz ARM */
89 R2_CM_CLKSEL_DSP_VAL, R2_CM_CLKSEL_GFX_VAL,
90 R2_CM_CLKSEL1_CORE_VAL, M4_CM_CLKSEL1_PLL_13_VAL,
91 MX_CLKSEL2_PLL_1x_VAL, R2_CM_CLKSEL_MDM_VAL,
92 SDRC_RFR_CTRL_133MHz,
93 RATE_IN_243X},
95 /* PRCM #2 - ratio1 (ES2) - SLOW */
96 {S13M, S329M, S164M, R1_CM_CLKSEL_MPU_VAL, /* 165MHz ARM */
97 R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
98 R1_CM_CLKSEL1_CORE_VAL, M2_CM_CLKSEL1_PLL_13_VAL,
99 MX_CLKSEL2_PLL_1x_VAL, R1_CM_CLKSEL_MDM_VAL,
100 SDRC_RFR_CTRL_165MHz,
101 RATE_IN_243X},
103 /* PRCM #5a - ratio1 - SLOW */
104 {S13M, S266M, S133M, R1_CM_CLKSEL_MPU_VAL, /* 133MHz ARM */
105 R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
106 R1_CM_CLKSEL1_CORE_VAL, M5A_CM_CLKSEL1_PLL_13_VAL,
107 MX_CLKSEL2_PLL_1x_VAL, R1_CM_CLKSEL_MDM_VAL,
108 SDRC_RFR_CTRL_133MHz,
109 RATE_IN_243X},
111 /* PRCM #5b - ratio1 - SLOW*/
112 {S13M, S200M, S100M, R1_CM_CLKSEL_MPU_VAL, /* 100MHz ARM */
113 R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
114 R1_CM_CLKSEL1_CORE_VAL, M5B_CM_CLKSEL1_PLL_13_VAL,
115 MX_CLKSEL2_PLL_1x_VAL, R1_CM_CLKSEL_MDM_VAL,
116 SDRC_RFR_CTRL_100MHz,
117 RATE_IN_243X},
119 /* PRCM-boot/bypass */
120 {S13M, S13M, S13M, RB_CM_CLKSEL_MPU_VAL, /* 13MHz */
121 RB_CM_CLKSEL_DSP_VAL, RB_CM_CLKSEL_GFX_VAL,
122 RB_CM_CLKSEL1_CORE_VAL, MB_CM_CLKSEL1_PLL_13_VAL,
123 MX_CLKSEL2_PLL_2x_VAL, RB_CM_CLKSEL_MDM_VAL,
124 SDRC_RFR_CTRL_BYPASS,
125 RATE_IN_243X},
127 /* PRCM-boot/bypass */
128 {S12M, S12M, S12M, RB_CM_CLKSEL_MPU_VAL, /* 12MHz */
129 RB_CM_CLKSEL_DSP_VAL, RB_CM_CLKSEL_GFX_VAL,
130 RB_CM_CLKSEL1_CORE_VAL, MB_CM_CLKSEL1_PLL_12_VAL,
131 MX_CLKSEL2_PLL_2x_VAL, RB_CM_CLKSEL_MDM_VAL,
132 SDRC_RFR_CTRL_BYPASS,
133 RATE_IN_243X},
135 { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},