1 Wolfson Arizona class audio SoCs
3 These devices are audio SoCs with extensive digital capabilites and a range
8 - compatible : One of the following chip-specific strings:
16 - reg : I2C slave address when connected using I2C, chip select number when
19 - interrupts : The interrupt line the /IRQ signal for the device is
21 - interrupt-controller : Arizona class devices contain interrupt controllers
22 and may provide interrupt services to other devices.
23 - interrupt-parent : The parent interrupt controller.
24 - #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
25 The first cell is the IRQ number.
26 The second cell is the flags, encoded as the trigger masks from
27 Documentation/devicetree/bindings/interrupts.txt
29 - gpio-controller : Indicates this device is a GPIO controller.
30 - #gpio-cells : Must be 2. The first cell is the pin number and the
31 second cell is used to specify optional parameters (currently unused).
33 - AVDD-supply, DBVDD1-supply, CPVDD-supply : Power supplies for the device,
34 as covered in Documentation/devicetree/bindings/regulator/regulator.txt
36 - DBVDD2-supply, DBVDD3-supply : Additional databus power supplies (wm5102,
37 wm5110, wm8280, wm8998, wm1814)
39 - SPKVDDL-supply, SPKVDDR-supply : Speaker driver power supplies (wm5102,
40 wm5110, wm8280, wm8998, wm1814)
42 - SPKVDD-supply : Speaker driver power supply (wm8997)
46 - wlf,reset : GPIO specifier for the GPIO controlling /RESET
48 - wlf,gpio-defaults : A list of GPIO configuration register values. Defines
49 for the appropriate values can found in <dt-bindings/mfd/arizona.txt>. If
50 absent, no configuration of these registers is performed. If any entry has
51 a value that is out of range for a 16 bit register then the chip default
52 will be used. If present exactly five values must be specified.
54 - wlf,inmode : A list of INn_MODE register values, where n is the number
55 of input signals. Valid values are 0 (Differential), 1 (Single-ended) and
56 2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default.
57 If present, values must be specified less than or equal to the number of
58 input signals. If values less than the number of input signals, elements
59 that have not been specified are set to 0 by default. Entries are:
60 <IN1, IN2, IN3, IN4> (wm5102, wm5110, wm8280, wm8997)
61 <IN1A, IN2A, IN1B, IN2B> (wm8998, wm1814)
63 - wlf,dmic-ref : DMIC reference voltage source for each input, can be
64 selected from either MICVDD or one of the MICBIAS's, defines
65 (ARIZONA_DMIC_xxxx) are provided in <dt-bindings/mfd/arizona.txt>. If
66 present, the number of values should be less than or equal to the
67 number of inputs, unspecified inputs will use the chip default.
69 - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if
70 they are being externally supplied. As covered in
71 Documentation/devicetree/bindings/regulator/regulator.txt
73 Also see child specific device properties:
74 Regulator - ../regulator/arizona-regulator.txt
75 Extcon - ../extcon/extcon-arizona.txt
80 compatible = "wlf,wm5102";
84 #interrupt-cells = <2>;
85 interrupt-parent = <&gic>;