arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 /dts-v1/;
   3 #include "bcm2835-rpi-cm1.dtsi"
   4 #include "bcm283x-rpi-usb-host.dtsi"
   5
   6 / {
   7         compatible = "raspberrypi,compute-module", "brcm,bcm2835";
   8         model = "Raspberry Pi Compute Module IO board rev1";
   9 };
  10
  11 &gpio {
  12         /*
  13          * This is based on the official GPU firmware DT blob.
  14          *
  15          * Legend:
  16          * "NC" = not connected (no rail from the SoC)
  17          * "FOO" = GPIO line named "FOO" on the schematic
  18          * "FOO_N" = GPIO line named "FOO" on schematic, active low
  19          */
  20         gpio-line-names = "GPIO0",
  21                           "GPIO1",
  22                           "GPIO2",
  23                           "GPIO3",
  24                           "GPIO4",
  25                           "GPIO5",
  26                           "GPIO6",
  27                           "GPIO7",
  28                           "GPIO8",
  29                           "GPIO9",
  30                           "GPIO10",
  31                           "GPIO11",
  32                           "GPIO12",
  33                           "GPIO13",
  34                           "GPIO14",
  35                           "GPIO15",
  36                           "GPIO16",
  37                           "GPIO17",
  38                           "GPIO18",
  39                           "GPIO19",
  40                           "GPIO20",
  41                           "GPIO21",
  42                           "GPIO22",
  43                           "GPIO23",
  44                           "GPIO24",
  45                           "GPIO25",
  46                           "GPIO26",
  47                           "GPIO27",
  48                           "GPIO28",
  49                           "GPIO29",
  50                           "GPIO30",
  51                           "GPIO31",
  52                           "GPIO32",
  53                           "GPIO33",
  54                           "GPIO34",
  55                           "GPIO35",
  56                           "GPIO36",
  57                           "GPIO37",
  58                           "GPIO38",
  59                           "GPIO39",
  60                           "GPIO40",
  61                           "GPIO41",
  62                           "GPIO42",
  63                           "GPIO43",
  64                           "GPIO44",
  65                           "GPIO45",
  66                           "HDMI_HPD_N",
  67                           /* Also used as ACT LED */
  68                           "EMMC_EN_N",
  69                           /* Used by eMMC */
  70                           "SD_CLK_R",
  71                           "SD_CMD_R",
  72                           "SD_DATA0_R",
  73                           "SD_DATA1_R",
  74                           "SD_DATA2_R",
  75                           "SD_DATA3_R";
  76
  77         pinctrl-0 = <&gpioout &alt0>;
  78 };
  79
  80 &hdmi {
  81         hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
  82         power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
  83         status = "okay";
  84 };
  85
  86 &sdhost {
  87         pinctrl-names = "default";
  88         pinctrl-0 = <&sdhost_gpio48>;
  89         bus-width = <4>;
  90         status = "okay";
  91 };
  92
  93 &uart0 {
  94         pinctrl-names = "default";
  95         pinctrl-0 = <&uart0_gpio14>;
  96         status = "okay";
  97 };