arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 #include "qcom-ipq8064.dtsi"
   3 #include <dt-bindings/input/input.h>
   4
   5 / {
   6         model = "Qualcomm Technologies, Inc. IPQ8064-v1.0";
   7
   8         aliases {
   9                 serial0 = &gsbi4_serial;
  10         };
  11
  12         chosen {
  13                 stdout-path = "serial0:115200n8";
  14         };
  15
  16         soc {
  17                 gsbi@16300000 {
  18                         qcom,mode = <GSBI_PROT_I2C_UART>;
  19                         status = "ok";
  20
  21                         serial@16340000 {
  22                                 status = "ok";
  23                         };
  24                 };
  25
  26                 gsbi5: gsbi@1a200000 {
  27                         qcom,mode = <GSBI_PROT_SPI>;
  28                         status = "ok";
  29
  30                         spi4: spi@1a280000 {
  31                                 status = "ok";
  32                                 spi-max-frequency = <50000000>;
  33
  34                                 pinctrl-0 = <&spi_pins>;
  35                                 pinctrl-names = "default";
  36
  37                                 cs-gpios = <&qcom_pinmux 20 0>;
  38
  39                                 flash: m25p80@0 {
  40                                         compatible = "s25fl256s1";
  41                                         #address-cells = <1>;
  42                                         #size-cells = <1>;
  43                                         spi-max-frequency = <50000000>;
  44                                         reg = <0>;
  45
  46                                         partition@0 {
  47                                                 label = "rootfs";
  48                                                 reg = <0x0 0x1000000>;
  49                                         };
  50
  51                                         partition@1 {
  52                                                 label = "scratch";
  53                                                 reg = <0x1000000 0x1000000>;
  54                                         };
  55                                 };
  56                         };
  57                 };
  58
  59                 sata-phy@1b400000 {
  60                         status = "ok";
  61                 };
  62
  63                 sata@29000000 {
  64                         ports-implemented = <0x1>;
  65                         status = "ok";
  66                 };
  67
  68                 gpio_keys {
  69                         compatible = "gpio-keys";
  70                         pinctrl-0 = <&buttons_pins>;
  71                         pinctrl-names = "default";
  72
  73                         button@1 {
  74                                 label = "reset";
  75                                 linux,code = <KEY_RESTART>;
  76                                 gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
  77                                 linux,input-type = <1>;
  78                                 debounce-interval = <60>;
  79                         };
  80                         button@2 {
  81                                 label = "wps";
  82                                 linux,code = <KEY_WPS_BUTTON>;
  83                                 gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
  84                                 linux,input-type = <1>;
  85                                 debounce-interval = <60>;
  86                         };
  87                 };
  88
  89                 leds {
  90                         compatible = "gpio-leds";
  91                         pinctrl-0 = <&leds_pins>;
  92                         pinctrl-names = "default";
  93
  94                         led@7 {
  95                                 label = "led_usb1";
  96                                 gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
  97                                 linux,default-trigger = "usbdev";
  98                                 default-state = "off";
  99                         };
 100
 101                         led@8 {
 102                                 label = "led_usb3";
 103                                 gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
 104                                 linux,default-trigger = "usbdev";
 105                                 default-state = "off";
 106                         };
 107
 108                         led@9 {
 109                                 label = "status_led_fail";
 110                                 gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
 111                                 default-state = "off";
 112                         };
 113
 114                         led@26 {
 115                                 label = "sata_led";
 116                                 gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
 117                                 default-state = "off";
 118                         };
 119
 120                         led@53 {
 121                                 label = "status_led_pass";
 122                                 gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
 123                                 default-state = "off";
 124                         };
 125                 };
 126         };
 127 };