Linux 4.19.133
[linux/fpc-iii.git] / drivers / gpio / gpio-max732x.c
blobf03cb0ba7726fb2776fce558b07cd4bfc81df6ed
1 /*
2 * MAX732x I2C Port Expander with 8/16 I/O
4 * Copyright (C) 2007 Marvell International Ltd.
5 * Copyright (C) 2008 Jack Ren <jack.ren@marvell.com>
6 * Copyright (C) 2008 Eric Miao <eric.miao@marvell.com>
7 * Copyright (C) 2015 Linus Walleij <linus.walleij@linaro.org>
9 * Derived from drivers/gpio/pca953x.c
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; version 2 of the License.
16 #include <linux/module.h>
17 #include <linux/init.h>
18 #include <linux/slab.h>
19 #include <linux/string.h>
20 #include <linux/gpio/driver.h>
21 #include <linux/interrupt.h>
22 #include <linux/i2c.h>
23 #include <linux/platform_data/max732x.h>
24 #include <linux/of.h>
28 * Each port of MAX732x (including MAX7319) falls into one of the
29 * following three types:
31 * - Push Pull Output
32 * - Input
33 * - Open Drain I/O
35 * designated by 'O', 'I' and 'P' individually according to MAXIM's
36 * datasheets. 'I' and 'P' ports are interrupt capables, some with
37 * a dedicated interrupt mask.
39 * There are two groups of I/O ports, each group usually includes
40 * up to 8 I/O ports, and is accessed by a specific I2C address:
42 * - Group A : by I2C address 0b'110xxxx
43 * - Group B : by I2C address 0b'101xxxx
45 * where 'xxxx' is decided by the connections of pin AD2/AD0. The
46 * address used also affects the initial state of output signals.
48 * Within each group of ports, there are five known combinations of
49 * I/O ports: 4I4O, 4P4O, 8I, 8P, 8O, see the definitions below for
50 * the detailed organization of these ports. Only Goup A is interrupt
51 * capable.
53 * GPIO numbers start from 'gpio_base + 0' to 'gpio_base + 8/16',
54 * and GPIOs from GROUP_A are numbered before those from GROUP_B
55 * (if there are two groups).
57 * NOTE: MAX7328/MAX7329 are drop-in replacements for PCF8574/a, so
58 * they are not supported by this driver.
61 #define PORT_NONE 0x0 /* '/' No Port */
62 #define PORT_OUTPUT 0x1 /* 'O' Push-Pull, Output Only */
63 #define PORT_INPUT 0x2 /* 'I' Input Only */
64 #define PORT_OPENDRAIN 0x3 /* 'P' Open-Drain, I/O */
66 #define IO_4I4O 0x5AA5 /* O7 O6 I5 I4 I3 I2 O1 O0 */
67 #define IO_4P4O 0x5FF5 /* O7 O6 P5 P4 P3 P2 O1 O0 */
68 #define IO_8I 0xAAAA /* I7 I6 I5 I4 I3 I2 I1 I0 */
69 #define IO_8P 0xFFFF /* P7 P6 P5 P4 P3 P2 P1 P0 */
70 #define IO_8O 0x5555 /* O7 O6 O5 O4 O3 O2 O1 O0 */
72 #define GROUP_A(x) ((x) & 0xffff) /* I2C Addr: 0b'110xxxx */
73 #define GROUP_B(x) ((x) << 16) /* I2C Addr: 0b'101xxxx */
75 #define INT_NONE 0x0 /* No interrupt capability */
76 #define INT_NO_MASK 0x1 /* Has interrupts, no mask */
77 #define INT_INDEP_MASK 0x2 /* Has interrupts, independent mask */
78 #define INT_MERGED_MASK 0x3 /* Has interrupts, merged mask */
80 #define INT_CAPS(x) (((uint64_t)(x)) << 32)
82 enum {
83 MAX7319,
84 MAX7320,
85 MAX7321,
86 MAX7322,
87 MAX7323,
88 MAX7324,
89 MAX7325,
90 MAX7326,
91 MAX7327,
94 static uint64_t max732x_features[] = {
95 [MAX7319] = GROUP_A(IO_8I) | INT_CAPS(INT_MERGED_MASK),
96 [MAX7320] = GROUP_B(IO_8O),
97 [MAX7321] = GROUP_A(IO_8P) | INT_CAPS(INT_NO_MASK),
98 [MAX7322] = GROUP_A(IO_4I4O) | INT_CAPS(INT_MERGED_MASK),
99 [MAX7323] = GROUP_A(IO_4P4O) | INT_CAPS(INT_INDEP_MASK),
100 [MAX7324] = GROUP_A(IO_8I) | GROUP_B(IO_8O) | INT_CAPS(INT_MERGED_MASK),
101 [MAX7325] = GROUP_A(IO_8P) | GROUP_B(IO_8O) | INT_CAPS(INT_NO_MASK),
102 [MAX7326] = GROUP_A(IO_4I4O) | GROUP_B(IO_8O) | INT_CAPS(INT_MERGED_MASK),
103 [MAX7327] = GROUP_A(IO_4P4O) | GROUP_B(IO_8O) | INT_CAPS(INT_NO_MASK),
106 static const struct i2c_device_id max732x_id[] = {
107 { "max7319", MAX7319 },
108 { "max7320", MAX7320 },
109 { "max7321", MAX7321 },
110 { "max7322", MAX7322 },
111 { "max7323", MAX7323 },
112 { "max7324", MAX7324 },
113 { "max7325", MAX7325 },
114 { "max7326", MAX7326 },
115 { "max7327", MAX7327 },
116 { },
118 MODULE_DEVICE_TABLE(i2c, max732x_id);
120 #ifdef CONFIG_OF
121 static const struct of_device_id max732x_of_table[] = {
122 { .compatible = "maxim,max7319" },
123 { .compatible = "maxim,max7320" },
124 { .compatible = "maxim,max7321" },
125 { .compatible = "maxim,max7322" },
126 { .compatible = "maxim,max7323" },
127 { .compatible = "maxim,max7324" },
128 { .compatible = "maxim,max7325" },
129 { .compatible = "maxim,max7326" },
130 { .compatible = "maxim,max7327" },
133 MODULE_DEVICE_TABLE(of, max732x_of_table);
134 #endif
136 struct max732x_chip {
137 struct gpio_chip gpio_chip;
139 struct i2c_client *client; /* "main" client */
140 struct i2c_client *client_dummy;
141 struct i2c_client *client_group_a;
142 struct i2c_client *client_group_b;
144 unsigned int mask_group_a;
145 unsigned int dir_input;
146 unsigned int dir_output;
148 struct mutex lock;
149 uint8_t reg_out[2];
151 #ifdef CONFIG_GPIO_MAX732X_IRQ
152 struct mutex irq_lock;
153 uint8_t irq_mask;
154 uint8_t irq_mask_cur;
155 uint8_t irq_trig_raise;
156 uint8_t irq_trig_fall;
157 uint8_t irq_features;
158 #endif
161 static int max732x_writeb(struct max732x_chip *chip, int group_a, uint8_t val)
163 struct i2c_client *client;
164 int ret;
166 client = group_a ? chip->client_group_a : chip->client_group_b;
167 ret = i2c_smbus_write_byte(client, val);
168 if (ret < 0) {
169 dev_err(&client->dev, "failed writing\n");
170 return ret;
173 return 0;
176 static int max732x_readb(struct max732x_chip *chip, int group_a, uint8_t *val)
178 struct i2c_client *client;
179 int ret;
181 client = group_a ? chip->client_group_a : chip->client_group_b;
182 ret = i2c_smbus_read_byte(client);
183 if (ret < 0) {
184 dev_err(&client->dev, "failed reading\n");
185 return ret;
188 *val = (uint8_t)ret;
189 return 0;
192 static inline int is_group_a(struct max732x_chip *chip, unsigned off)
194 return (1u << off) & chip->mask_group_a;
197 static int max732x_gpio_get_value(struct gpio_chip *gc, unsigned off)
199 struct max732x_chip *chip = gpiochip_get_data(gc);
200 uint8_t reg_val;
201 int ret;
203 ret = max732x_readb(chip, is_group_a(chip, off), &reg_val);
204 if (ret < 0)
205 return ret;
207 return !!(reg_val & (1u << (off & 0x7)));
210 static void max732x_gpio_set_mask(struct gpio_chip *gc, unsigned off, int mask,
211 int val)
213 struct max732x_chip *chip = gpiochip_get_data(gc);
214 uint8_t reg_out;
215 int ret;
217 mutex_lock(&chip->lock);
219 reg_out = (off > 7) ? chip->reg_out[1] : chip->reg_out[0];
220 reg_out = (reg_out & ~mask) | (val & mask);
222 ret = max732x_writeb(chip, is_group_a(chip, off), reg_out);
223 if (ret < 0)
224 goto out;
226 /* update the shadow register then */
227 if (off > 7)
228 chip->reg_out[1] = reg_out;
229 else
230 chip->reg_out[0] = reg_out;
231 out:
232 mutex_unlock(&chip->lock);
235 static void max732x_gpio_set_value(struct gpio_chip *gc, unsigned off, int val)
237 unsigned base = off & ~0x7;
238 uint8_t mask = 1u << (off & 0x7);
240 max732x_gpio_set_mask(gc, base, mask, val << (off & 0x7));
243 static void max732x_gpio_set_multiple(struct gpio_chip *gc,
244 unsigned long *mask, unsigned long *bits)
246 unsigned mask_lo = mask[0] & 0xff;
247 unsigned mask_hi = (mask[0] >> 8) & 0xff;
249 if (mask_lo)
250 max732x_gpio_set_mask(gc, 0, mask_lo, bits[0] & 0xff);
251 if (mask_hi)
252 max732x_gpio_set_mask(gc, 8, mask_hi, (bits[0] >> 8) & 0xff);
255 static int max732x_gpio_direction_input(struct gpio_chip *gc, unsigned off)
257 struct max732x_chip *chip = gpiochip_get_data(gc);
258 unsigned int mask = 1u << off;
260 if ((mask & chip->dir_input) == 0) {
261 dev_dbg(&chip->client->dev, "%s port %d is output only\n",
262 chip->client->name, off);
263 return -EACCES;
267 * Open-drain pins must be set to high impedance (which is
268 * equivalent to output-high) to be turned into an input.
270 if ((mask & chip->dir_output))
271 max732x_gpio_set_value(gc, off, 1);
273 return 0;
276 static int max732x_gpio_direction_output(struct gpio_chip *gc,
277 unsigned off, int val)
279 struct max732x_chip *chip = gpiochip_get_data(gc);
280 unsigned int mask = 1u << off;
282 if ((mask & chip->dir_output) == 0) {
283 dev_dbg(&chip->client->dev, "%s port %d is input only\n",
284 chip->client->name, off);
285 return -EACCES;
288 max732x_gpio_set_value(gc, off, val);
289 return 0;
292 #ifdef CONFIG_GPIO_MAX732X_IRQ
293 static int max732x_writew(struct max732x_chip *chip, uint16_t val)
295 int ret;
297 val = cpu_to_le16(val);
299 ret = i2c_master_send(chip->client_group_a, (char *)&val, 2);
300 if (ret < 0) {
301 dev_err(&chip->client_group_a->dev, "failed writing\n");
302 return ret;
305 return 0;
308 static int max732x_readw(struct max732x_chip *chip, uint16_t *val)
310 int ret;
312 ret = i2c_master_recv(chip->client_group_a, (char *)val, 2);
313 if (ret < 0) {
314 dev_err(&chip->client_group_a->dev, "failed reading\n");
315 return ret;
318 *val = le16_to_cpu(*val);
319 return 0;
322 static void max732x_irq_update_mask(struct max732x_chip *chip)
324 uint16_t msg;
326 if (chip->irq_mask == chip->irq_mask_cur)
327 return;
329 chip->irq_mask = chip->irq_mask_cur;
331 if (chip->irq_features == INT_NO_MASK)
332 return;
334 mutex_lock(&chip->lock);
336 switch (chip->irq_features) {
337 case INT_INDEP_MASK:
338 msg = (chip->irq_mask << 8) | chip->reg_out[0];
339 max732x_writew(chip, msg);
340 break;
342 case INT_MERGED_MASK:
343 msg = chip->irq_mask | chip->reg_out[0];
344 max732x_writeb(chip, 1, (uint8_t)msg);
345 break;
348 mutex_unlock(&chip->lock);
351 static void max732x_irq_mask(struct irq_data *d)
353 struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
354 struct max732x_chip *chip = gpiochip_get_data(gc);
356 chip->irq_mask_cur &= ~(1 << d->hwirq);
359 static void max732x_irq_unmask(struct irq_data *d)
361 struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
362 struct max732x_chip *chip = gpiochip_get_data(gc);
364 chip->irq_mask_cur |= 1 << d->hwirq;
367 static void max732x_irq_bus_lock(struct irq_data *d)
369 struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
370 struct max732x_chip *chip = gpiochip_get_data(gc);
372 mutex_lock(&chip->irq_lock);
373 chip->irq_mask_cur = chip->irq_mask;
376 static void max732x_irq_bus_sync_unlock(struct irq_data *d)
378 struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
379 struct max732x_chip *chip = gpiochip_get_data(gc);
380 uint16_t new_irqs;
381 uint16_t level;
383 max732x_irq_update_mask(chip);
385 new_irqs = chip->irq_trig_fall | chip->irq_trig_raise;
386 while (new_irqs) {
387 level = __ffs(new_irqs);
388 max732x_gpio_direction_input(&chip->gpio_chip, level);
389 new_irqs &= ~(1 << level);
392 mutex_unlock(&chip->irq_lock);
395 static int max732x_irq_set_type(struct irq_data *d, unsigned int type)
397 struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
398 struct max732x_chip *chip = gpiochip_get_data(gc);
399 uint16_t off = d->hwirq;
400 uint16_t mask = 1 << off;
402 if (!(mask & chip->dir_input)) {
403 dev_dbg(&chip->client->dev, "%s port %d is output only\n",
404 chip->client->name, off);
405 return -EACCES;
408 if (!(type & IRQ_TYPE_EDGE_BOTH)) {
409 dev_err(&chip->client->dev, "irq %d: unsupported type %d\n",
410 d->irq, type);
411 return -EINVAL;
414 if (type & IRQ_TYPE_EDGE_FALLING)
415 chip->irq_trig_fall |= mask;
416 else
417 chip->irq_trig_fall &= ~mask;
419 if (type & IRQ_TYPE_EDGE_RISING)
420 chip->irq_trig_raise |= mask;
421 else
422 chip->irq_trig_raise &= ~mask;
424 return 0;
427 static int max732x_irq_set_wake(struct irq_data *data, unsigned int on)
429 struct max732x_chip *chip = irq_data_get_irq_chip_data(data);
431 irq_set_irq_wake(chip->client->irq, on);
432 return 0;
435 static struct irq_chip max732x_irq_chip = {
436 .name = "max732x",
437 .irq_mask = max732x_irq_mask,
438 .irq_unmask = max732x_irq_unmask,
439 .irq_bus_lock = max732x_irq_bus_lock,
440 .irq_bus_sync_unlock = max732x_irq_bus_sync_unlock,
441 .irq_set_type = max732x_irq_set_type,
442 .irq_set_wake = max732x_irq_set_wake,
445 static uint8_t max732x_irq_pending(struct max732x_chip *chip)
447 uint8_t cur_stat;
448 uint8_t old_stat;
449 uint8_t trigger;
450 uint8_t pending;
451 uint16_t status;
452 int ret;
454 ret = max732x_readw(chip, &status);
455 if (ret)
456 return 0;
458 trigger = status >> 8;
459 trigger &= chip->irq_mask;
461 if (!trigger)
462 return 0;
464 cur_stat = status & 0xFF;
465 cur_stat &= chip->irq_mask;
467 old_stat = cur_stat ^ trigger;
469 pending = (old_stat & chip->irq_trig_fall) |
470 (cur_stat & chip->irq_trig_raise);
471 pending &= trigger;
473 return pending;
476 static irqreturn_t max732x_irq_handler(int irq, void *devid)
478 struct max732x_chip *chip = devid;
479 uint8_t pending;
480 uint8_t level;
482 pending = max732x_irq_pending(chip);
484 if (!pending)
485 return IRQ_HANDLED;
487 do {
488 level = __ffs(pending);
489 handle_nested_irq(irq_find_mapping(chip->gpio_chip.irq.domain,
490 level));
492 pending &= ~(1 << level);
493 } while (pending);
495 return IRQ_HANDLED;
498 static int max732x_irq_setup(struct max732x_chip *chip,
499 const struct i2c_device_id *id)
501 struct i2c_client *client = chip->client;
502 struct max732x_platform_data *pdata = dev_get_platdata(&client->dev);
503 int has_irq = max732x_features[id->driver_data] >> 32;
504 int irq_base = 0;
505 int ret;
507 if (((pdata && pdata->irq_base) || client->irq)
508 && has_irq != INT_NONE) {
509 if (pdata)
510 irq_base = pdata->irq_base;
511 chip->irq_features = has_irq;
512 mutex_init(&chip->irq_lock);
514 ret = devm_request_threaded_irq(&client->dev, client->irq,
515 NULL, max732x_irq_handler, IRQF_ONESHOT |
516 IRQF_TRIGGER_FALLING | IRQF_SHARED,
517 dev_name(&client->dev), chip);
518 if (ret) {
519 dev_err(&client->dev, "failed to request irq %d\n",
520 client->irq);
521 return ret;
523 ret = gpiochip_irqchip_add_nested(&chip->gpio_chip,
524 &max732x_irq_chip,
525 irq_base,
526 handle_simple_irq,
527 IRQ_TYPE_NONE);
528 if (ret) {
529 dev_err(&client->dev,
530 "could not connect irqchip to gpiochip\n");
531 return ret;
533 gpiochip_set_nested_irqchip(&chip->gpio_chip,
534 &max732x_irq_chip,
535 client->irq);
538 return 0;
541 #else /* CONFIG_GPIO_MAX732X_IRQ */
542 static int max732x_irq_setup(struct max732x_chip *chip,
543 const struct i2c_device_id *id)
545 struct i2c_client *client = chip->client;
546 struct max732x_platform_data *pdata = dev_get_platdata(&client->dev);
547 int has_irq = max732x_features[id->driver_data] >> 32;
549 if (((pdata && pdata->irq_base) || client->irq) && has_irq != INT_NONE)
550 dev_warn(&client->dev, "interrupt support not compiled in\n");
552 return 0;
554 #endif
556 static int max732x_setup_gpio(struct max732x_chip *chip,
557 const struct i2c_device_id *id,
558 unsigned gpio_start)
560 struct gpio_chip *gc = &chip->gpio_chip;
561 uint32_t id_data = (uint32_t)max732x_features[id->driver_data];
562 int i, port = 0;
564 for (i = 0; i < 16; i++, id_data >>= 2) {
565 unsigned int mask = 1 << port;
567 switch (id_data & 0x3) {
568 case PORT_OUTPUT:
569 chip->dir_output |= mask;
570 break;
571 case PORT_INPUT:
572 chip->dir_input |= mask;
573 break;
574 case PORT_OPENDRAIN:
575 chip->dir_output |= mask;
576 chip->dir_input |= mask;
577 break;
578 default:
579 continue;
582 if (i < 8)
583 chip->mask_group_a |= mask;
584 port++;
587 if (chip->dir_input)
588 gc->direction_input = max732x_gpio_direction_input;
589 if (chip->dir_output) {
590 gc->direction_output = max732x_gpio_direction_output;
591 gc->set = max732x_gpio_set_value;
592 gc->set_multiple = max732x_gpio_set_multiple;
594 gc->get = max732x_gpio_get_value;
595 gc->can_sleep = true;
597 gc->base = gpio_start;
598 gc->ngpio = port;
599 gc->label = chip->client->name;
600 gc->parent = &chip->client->dev;
601 gc->owner = THIS_MODULE;
603 return port;
606 static struct max732x_platform_data *of_gpio_max732x(struct device *dev)
608 struct max732x_platform_data *pdata;
610 pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
611 if (!pdata)
612 return NULL;
614 pdata->gpio_base = -1;
616 return pdata;
619 static int max732x_probe(struct i2c_client *client,
620 const struct i2c_device_id *id)
622 struct max732x_platform_data *pdata;
623 struct device_node *node;
624 struct max732x_chip *chip;
625 struct i2c_client *c;
626 uint16_t addr_a, addr_b;
627 int ret, nr_port;
629 pdata = dev_get_platdata(&client->dev);
630 node = client->dev.of_node;
632 if (!pdata && node)
633 pdata = of_gpio_max732x(&client->dev);
635 if (!pdata) {
636 dev_dbg(&client->dev, "no platform data\n");
637 return -EINVAL;
640 chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
641 if (chip == NULL)
642 return -ENOMEM;
643 chip->client = client;
645 nr_port = max732x_setup_gpio(chip, id, pdata->gpio_base);
646 chip->gpio_chip.parent = &client->dev;
648 addr_a = (client->addr & 0x0f) | 0x60;
649 addr_b = (client->addr & 0x0f) | 0x50;
651 switch (client->addr & 0x70) {
652 case 0x60:
653 chip->client_group_a = client;
654 if (nr_port > 8) {
655 c = i2c_new_dummy(client->adapter, addr_b);
656 if (!c) {
657 dev_err(&client->dev,
658 "Failed to allocate I2C device\n");
659 ret = -ENODEV;
660 goto out_failed;
662 chip->client_group_b = chip->client_dummy = c;
664 break;
665 case 0x50:
666 chip->client_group_b = client;
667 if (nr_port > 8) {
668 c = i2c_new_dummy(client->adapter, addr_a);
669 if (!c) {
670 dev_err(&client->dev,
671 "Failed to allocate I2C device\n");
672 ret = -ENODEV;
673 goto out_failed;
675 chip->client_group_a = chip->client_dummy = c;
677 break;
678 default:
679 dev_err(&client->dev, "invalid I2C address specified %02x\n",
680 client->addr);
681 ret = -EINVAL;
682 goto out_failed;
685 if (nr_port > 8 && !chip->client_dummy) {
686 dev_err(&client->dev,
687 "Failed to allocate second group I2C device\n");
688 ret = -ENODEV;
689 goto out_failed;
692 mutex_init(&chip->lock);
694 ret = max732x_readb(chip, is_group_a(chip, 0), &chip->reg_out[0]);
695 if (ret)
696 goto out_failed;
697 if (nr_port > 8) {
698 ret = max732x_readb(chip, is_group_a(chip, 8), &chip->reg_out[1]);
699 if (ret)
700 goto out_failed;
703 ret = gpiochip_add_data(&chip->gpio_chip, chip);
704 if (ret)
705 goto out_failed;
707 ret = max732x_irq_setup(chip, id);
708 if (ret) {
709 gpiochip_remove(&chip->gpio_chip);
710 goto out_failed;
713 if (pdata && pdata->setup) {
714 ret = pdata->setup(client, chip->gpio_chip.base,
715 chip->gpio_chip.ngpio, pdata->context);
716 if (ret < 0)
717 dev_warn(&client->dev, "setup failed, %d\n", ret);
720 i2c_set_clientdata(client, chip);
721 return 0;
723 out_failed:
724 i2c_unregister_device(chip->client_dummy);
725 return ret;
728 static int max732x_remove(struct i2c_client *client)
730 struct max732x_platform_data *pdata = dev_get_platdata(&client->dev);
731 struct max732x_chip *chip = i2c_get_clientdata(client);
733 if (pdata && pdata->teardown) {
734 int ret;
736 ret = pdata->teardown(client, chip->gpio_chip.base,
737 chip->gpio_chip.ngpio, pdata->context);
738 if (ret < 0) {
739 dev_err(&client->dev, "%s failed, %d\n",
740 "teardown", ret);
741 return ret;
745 gpiochip_remove(&chip->gpio_chip);
747 /* unregister any dummy i2c_client */
748 i2c_unregister_device(chip->client_dummy);
750 return 0;
753 static struct i2c_driver max732x_driver = {
754 .driver = {
755 .name = "max732x",
756 .of_match_table = of_match_ptr(max732x_of_table),
758 .probe = max732x_probe,
759 .remove = max732x_remove,
760 .id_table = max732x_id,
763 static int __init max732x_init(void)
765 return i2c_add_driver(&max732x_driver);
767 /* register after i2c postcore initcall and before
768 * subsys initcalls that may rely on these GPIOs
770 subsys_initcall(max732x_init);
772 static void __exit max732x_exit(void)
774 i2c_del_driver(&max732x_driver);
776 module_exit(max732x_exit);
778 MODULE_AUTHOR("Eric Miao <eric.miao@marvell.com>");
779 MODULE_DESCRIPTION("GPIO expander driver for MAX732X");
780 MODULE_LICENSE("GPL");