drivers/spi/spi-sprd-adi.c

   1 /*
   2  * Copyright (C) 2017 Spreadtrum Communications Inc.
   3  *
   4  * SPDX-License-Identifier: GPL-2.0
   5  */
   6
   7 #include <linux/delay.h>
   8 #include <linux/hwspinlock.h>
   9 #include <linux/init.h>
  10 #include <linux/io.h>
  11 #include <linux/kernel.h>
  12 #include <linux/module.h>
  13 #include <linux/of.h>
  14 #include <linux/of_device.h>
  15 #include <linux/platform_device.h>
  16 #include <linux/reboot.h>
  17 #include <linux/spi/spi.h>
  18 #include <linux/sizes.h>
  19
  20 /* Registers definitions for ADI controller */
  21 #define REG_ADI_CTRL0                   0x4
  22 #define REG_ADI_CHN_PRIL                0x8
  23 #define REG_ADI_CHN_PRIH                0xc
  24 #define REG_ADI_INT_EN                  0x10
  25 #define REG_ADI_INT_RAW                 0x14
  26 #define REG_ADI_INT_MASK                0x18
  27 #define REG_ADI_INT_CLR                 0x1c
  28 #define REG_ADI_GSSI_CFG0               0x20
  29 #define REG_ADI_GSSI_CFG1               0x24
  30 #define REG_ADI_RD_CMD                  0x28
  31 #define REG_ADI_RD_DATA                 0x2c
  32 #define REG_ADI_ARM_FIFO_STS            0x30
  33 #define REG_ADI_STS                     0x34
  34 #define REG_ADI_EVT_FIFO_STS            0x38
  35 #define REG_ADI_ARM_CMD_STS             0x3c
  36 #define REG_ADI_CHN_EN                  0x40
  37 #define REG_ADI_CHN_ADDR(id)            (0x44 + (id - 2) * 4)
  38 #define REG_ADI_CHN_EN1                 0x20c
  39
  40 /* Bits definitions for register REG_ADI_GSSI_CFG0 */
  41 #define BIT_CLK_ALL_ON                  BIT(30)
  42
  43 /* Bits definitions for register REG_ADI_RD_DATA */
  44 #define BIT_RD_CMD_BUSY                 BIT(31)
  45 #define RD_ADDR_SHIFT                   16
  46 #define RD_VALUE_MASK                   GENMASK(15, 0)
  47 #define RD_ADDR_MASK                    GENMASK(30, 16)
  48
  49 /* Bits definitions for register REG_ADI_ARM_FIFO_STS */
  50 #define BIT_FIFO_FULL                   BIT(11)
  51 #define BIT_FIFO_EMPTY                  BIT(10)
  52
  53 /*
  54  * ADI slave devices include RTC, ADC, regulator, charger, thermal and so on.
  55  * The slave devices address offset is always 0x8000 and size is 4K.
  56  */
  57 #define ADI_SLAVE_ADDR_SIZE             SZ_4K
  58 #define ADI_SLAVE_OFFSET                0x8000
  59
  60 /* Timeout (ms) for the trylock of hardware spinlocks */
  61 #define ADI_HWSPINLOCK_TIMEOUT          5000
  62 /*
  63  * ADI controller has 50 channels including 2 software channels
  64  * and 48 hardware channels.
  65  */
  66 #define ADI_HW_CHNS                     50
  67
  68 #define ADI_FIFO_DRAIN_TIMEOUT          1000
  69 #define ADI_READ_TIMEOUT                2000
  70 #define REG_ADDR_LOW_MASK               GENMASK(11, 0)
  71
  72 /* Registers definitions for PMIC watchdog controller */
  73 #define REG_WDG_LOAD_LOW                0x80
  74 #define REG_WDG_LOAD_HIGH               0x84
  75 #define REG_WDG_CTRL                    0x88
  76 #define REG_WDG_LOCK                    0xa0
  77
  78 /* Bits definitions for register REG_WDG_CTRL */
  79 #define BIT_WDG_RUN                     BIT(1)
  80 #define BIT_WDG_RST                     BIT(3)
  81
  82 /* Registers definitions for PMIC */
  83 #define PMIC_RST_STATUS                 0xee8
  84 #define PMIC_MODULE_EN                  0xc08
  85 #define PMIC_CLK_EN                     0xc18
  86 #define BIT_WDG_EN                      BIT(2)
  87
  88 /* Definition of PMIC reset status register */
  89 #define HWRST_STATUS_RECOVERY           0x20
  90 #define HWRST_STATUS_NORMAL             0x40
  91 #define HWRST_STATUS_ALARM              0x50
  92 #define HWRST_STATUS_SLEEP              0x60
  93 #define HWRST_STATUS_FASTBOOT           0x30
  94 #define HWRST_STATUS_SPECIAL            0x70
  95 #define HWRST_STATUS_PANIC              0x80
  96 #define HWRST_STATUS_CFTREBOOT          0x90
  97 #define HWRST_STATUS_AUTODLOADER        0xa0
  98 #define HWRST_STATUS_IQMODE             0xb0
  99 #define HWRST_STATUS_SPRDISK            0xc0
 100
 101 /* Use default timeout 50 ms that converts to watchdog values */
 102 #define WDG_LOAD_VAL                    ((50 * 1000) / 32768)
 103 #define WDG_LOAD_MASK                   GENMASK(15, 0)
 104 #define WDG_UNLOCK_KEY                  0xe551
 105
 106 struct sprd_adi {
 107         struct spi_controller   *ctlr;
 108         struct device           *dev;
 109         void __iomem            *base;
 110         struct hwspinlock       *hwlock;
 111         unsigned long           slave_vbase;
 112         unsigned long           slave_pbase;
 113         struct notifier_block   restart_handler;
 114 };
 115
 116 static int sprd_adi_check_paddr(struct sprd_adi *sadi, u32 paddr)
 117 {
 118         if (paddr < sadi->slave_pbase || paddr >
 119             (sadi->slave_pbase + ADI_SLAVE_ADDR_SIZE)) {
 120                 dev_err(sadi->dev,
 121                         "slave physical address is incorrect, addr = 0x%x\n",
 122                         paddr);
 123                 return -EINVAL;
 124         }
 125
 126         return 0;
 127 }
 128
 129 static unsigned long sprd_adi_to_vaddr(struct sprd_adi *sadi, u32 paddr)
 130 {
 131         return (paddr - sadi->slave_pbase + sadi->slave_vbase);
 132 }
 133
 134 static int sprd_adi_drain_fifo(struct sprd_adi *sadi)
 135 {
 136         u32 timeout = ADI_FIFO_DRAIN_TIMEOUT;
 137         u32 sts;
 138
 139         do {
 140                 sts = readl_relaxed(sadi->base + REG_ADI_ARM_FIFO_STS);
 141                 if (sts & BIT_FIFO_EMPTY)
 142                         break;
 143
 144                 cpu_relax();
 145         } while (--timeout);
 146
 147         if (timeout == 0) {
 148                 dev_err(sadi->dev, "drain write fifo timeout\n");
 149                 return -EBUSY;
 150         }
 151
 152         return 0;
 153 }
 154
 155 static int sprd_adi_fifo_is_full(struct sprd_adi *sadi)
 156 {
 157         return readl_relaxed(sadi->base + REG_ADI_ARM_FIFO_STS) & BIT_FIFO_FULL;
 158 }
 159
 160 static int sprd_adi_read(struct sprd_adi *sadi, u32 reg_paddr, u32 *read_val)
 161 {
 162         int read_timeout = ADI_READ_TIMEOUT;
 163         unsigned long flags;
 164         u32 val, rd_addr;
 165         int ret;
 166
 167         ret = hwspin_lock_timeout_irqsave(sadi->hwlock,
 168                                           ADI_HWSPINLOCK_TIMEOUT,
 169                                           &flags);
 170         if (ret) {
 171                 dev_err(sadi->dev, "get the hw lock failed\n");
 172                 return ret;
 173         }
 174
 175         /*
 176          * Set the physical register address need to read into RD_CMD register,
 177          * then ADI controller will start to transfer automatically.
 178          */
 179         writel_relaxed(reg_paddr, sadi->base + REG_ADI_RD_CMD);
 180
 181         /*
 182          * Wait read operation complete, the BIT_RD_CMD_BUSY will be set
 183          * simultaneously when writing read command to register, and the
 184          * BIT_RD_CMD_BUSY will be cleared after the read operation is
 185          * completed.
 186          */
 187         do {
 188                 val = readl_relaxed(sadi->base + REG_ADI_RD_DATA);
 189                 if (!(val & BIT_RD_CMD_BUSY))
 190                         break;
 191
 192                 cpu_relax();
 193         } while (--read_timeout);
 194
 195         if (read_timeout == 0) {
 196                 dev_err(sadi->dev, "ADI read timeout\n");
 197                 ret = -EBUSY;
 198                 goto out;
 199         }
 200
 201         /*
 202          * The return value includes data and read register address, from bit 0
 203          * to bit 15 are data, and from bit 16 to bit 30 are read register
 204          * address. Then we can check the returned register address to validate
 205          * data.
 206          */
 207         rd_addr = (val & RD_ADDR_MASK ) >> RD_ADDR_SHIFT;
 208
 209         if (rd_addr != (reg_paddr & REG_ADDR_LOW_MASK)) {
 210                 dev_err(sadi->dev, "read error, reg addr = 0x%x, val = 0x%x\n",
 211                         reg_paddr, val);
 212                 ret = -EIO;
 213                 goto out;
 214         }
 215
 216         *read_val = val & RD_VALUE_MASK;
 217
 218 out:
 219         hwspin_unlock_irqrestore(sadi->hwlock, &flags);
 220         return ret;
 221 }
 222
 223 static int sprd_adi_write(struct sprd_adi *sadi, u32 reg_paddr, u32 val)
 224 {
 225         unsigned long reg = sprd_adi_to_vaddr(sadi, reg_paddr);
 226         u32 timeout = ADI_FIFO_DRAIN_TIMEOUT;
 227         unsigned long flags;
 228         int ret;
 229
 230         ret = hwspin_lock_timeout_irqsave(sadi->hwlock,
 231                                           ADI_HWSPINLOCK_TIMEOUT,
 232                                           &flags);
 233         if (ret) {
 234                 dev_err(sadi->dev, "get the hw lock failed\n");
 235                 return ret;
 236         }
 237
 238         ret = sprd_adi_drain_fifo(sadi);
 239         if (ret < 0)
 240                 goto out;
 241
 242         /*
 243          * we should wait for write fifo is empty before writing data to PMIC
 244          * registers.
 245          */
 246         do {
 247                 if (!sprd_adi_fifo_is_full(sadi)) {
 248                         writel_relaxed(val, (void __iomem *)reg);
 249                         break;
 250                 }
 251
 252                 cpu_relax();
 253         } while (--timeout);
 254
 255         if (timeout == 0) {
 256                 dev_err(sadi->dev, "write fifo is full\n");
 257                 ret = -EBUSY;
 258         }
 259
 260 out:
 261         hwspin_unlock_irqrestore(sadi->hwlock, &flags);
 262         return ret;
 263 }
 264
 265 static int sprd_adi_transfer_one(struct spi_controller *ctlr,
 266                                  struct spi_device *spi_dev,
 267                                  struct spi_transfer *t)
 268 {
 269         struct sprd_adi *sadi = spi_controller_get_devdata(ctlr);
 270         u32 phy_reg, val;
 271         int ret;
 272
 273         if (t->rx_buf) {
 274                 phy_reg = *(u32 *)t->rx_buf + sadi->slave_pbase;
 275
 276                 ret = sprd_adi_check_paddr(sadi, phy_reg);
 277                 if (ret)
 278                         return ret;
 279
 280                 ret = sprd_adi_read(sadi, phy_reg, &val);
 281                 if (ret)
 282                         return ret;
 283
 284                 *(u32 *)t->rx_buf = val;
 285         } else if (t->tx_buf) {
 286                 u32 *p = (u32 *)t->tx_buf;
 287
 288                 /*
 289                  * Get the physical register address need to write and convert
 290                  * the physical address to virtual address. Since we need
 291                  * virtual register address to write.
 292                  */
 293                 phy_reg = *p++ + sadi->slave_pbase;
 294                 ret = sprd_adi_check_paddr(sadi, phy_reg);
 295                 if (ret)
 296                         return ret;
 297
 298                 val = *p;
 299                 ret = sprd_adi_write(sadi, phy_reg, val);
 300                 if (ret)
 301                         return ret;
 302         } else {
 303                 dev_err(sadi->dev, "no buffer for transfer\n");
 304                 return -EINVAL;
 305         }
 306
 307         return 0;
 308 }
 309
 310 static int sprd_adi_restart_handler(struct notifier_block *this,
 311                                     unsigned long mode, void *cmd)
 312 {
 313         struct sprd_adi *sadi = container_of(this, struct sprd_adi,
 314                                              restart_handler);
 315         u32 val, reboot_mode = 0;
 316
 317         if (!cmd)
 318                 reboot_mode = HWRST_STATUS_NORMAL;
 319         else if (!strncmp(cmd, "recovery", 8))
 320                 reboot_mode = HWRST_STATUS_RECOVERY;
 321         else if (!strncmp(cmd, "alarm", 5))
 322                 reboot_mode = HWRST_STATUS_ALARM;
 323         else if (!strncmp(cmd, "fastsleep", 9))
 324                 reboot_mode = HWRST_STATUS_SLEEP;
 325         else if (!strncmp(cmd, "bootloader", 10))
 326                 reboot_mode = HWRST_STATUS_FASTBOOT;
 327         else if (!strncmp(cmd, "panic", 5))
 328                 reboot_mode = HWRST_STATUS_PANIC;
 329         else if (!strncmp(cmd, "special", 7))
 330                 reboot_mode = HWRST_STATUS_SPECIAL;
 331         else if (!strncmp(cmd, "cftreboot", 9))
 332                 reboot_mode = HWRST_STATUS_CFTREBOOT;
 333         else if (!strncmp(cmd, "autodloader", 11))
 334                 reboot_mode = HWRST_STATUS_AUTODLOADER;
 335         else if (!strncmp(cmd, "iqmode", 6))
 336                 reboot_mode = HWRST_STATUS_IQMODE;
 337         else if (!strncmp(cmd, "sprdisk", 7))
 338                 reboot_mode = HWRST_STATUS_SPRDISK;
 339         else
 340                 reboot_mode = HWRST_STATUS_NORMAL;
 341
 342         /* Record the reboot mode */
 343         sprd_adi_read(sadi, sadi->slave_pbase + PMIC_RST_STATUS, &val);
 344         val |= reboot_mode;
 345         sprd_adi_write(sadi, sadi->slave_pbase + PMIC_RST_STATUS, val);
 346
 347         /* Enable the interface clock of the watchdog */
 348         sprd_adi_read(sadi, sadi->slave_pbase + PMIC_MODULE_EN, &val);
 349         val |= BIT_WDG_EN;
 350         sprd_adi_write(sadi, sadi->slave_pbase + PMIC_MODULE_EN, val);
 351
 352         /* Enable the work clock of the watchdog */
 353         sprd_adi_read(sadi, sadi->slave_pbase + PMIC_CLK_EN, &val);
 354         val |= BIT_WDG_EN;
 355         sprd_adi_write(sadi, sadi->slave_pbase + PMIC_CLK_EN, val);
 356
 357         /* Unlock the watchdog */
 358         sprd_adi_write(sadi, sadi->slave_pbase + REG_WDG_LOCK, WDG_UNLOCK_KEY);
 359
 360         /* Load the watchdog timeout value, 50ms is always enough. */
 361         sprd_adi_write(sadi, sadi->slave_pbase + REG_WDG_LOAD_LOW,
 362                        WDG_LOAD_VAL & WDG_LOAD_MASK);
 363         sprd_adi_write(sadi, sadi->slave_pbase + REG_WDG_LOAD_HIGH, 0);
 364
 365         /* Start the watchdog to reset system */
 366         sprd_adi_read(sadi, sadi->slave_pbase + REG_WDG_CTRL, &val);
 367         val |= BIT_WDG_RUN | BIT_WDG_RST;
 368         sprd_adi_write(sadi, sadi->slave_pbase + REG_WDG_CTRL, val);
 369
 370         /* Lock the watchdog */
 371         sprd_adi_write(sadi, sadi->slave_pbase + REG_WDG_LOCK, ~WDG_UNLOCK_KEY);
 372
 373         mdelay(1000);
 374
 375         dev_emerg(sadi->dev, "Unable to restart system\n");
 376         return NOTIFY_DONE;
 377 }
 378
 379 static void sprd_adi_hw_init(struct sprd_adi *sadi)
 380 {
 381         struct device_node *np = sadi->dev->of_node;
 382         int i, size, chn_cnt;
 383         const __be32 *list;
 384         u32 tmp;
 385
 386         /* Address bits select default 12 bits */
 387         writel_relaxed(0, sadi->base + REG_ADI_CTRL0);
 388
 389         /* Set all channels as default priority */
 390         writel_relaxed(0, sadi->base + REG_ADI_CHN_PRIL);
 391         writel_relaxed(0, sadi->base + REG_ADI_CHN_PRIH);
 392
 393         /* Set clock auto gate mode */
 394         tmp = readl_relaxed(sadi->base + REG_ADI_GSSI_CFG0);
 395         tmp &= ~BIT_CLK_ALL_ON;
 396         writel_relaxed(tmp, sadi->base + REG_ADI_GSSI_CFG0);
 397
 398         /* Set hardware channels setting */
 399         list = of_get_property(np, "sprd,hw-channels", &size);
 400         if (!list || !size) {
 401                 dev_info(sadi->dev, "no hw channels setting in node\n");
 402                 return;
 403         }
 404
 405         chn_cnt = size / 8;
 406         for (i = 0; i < chn_cnt; i++) {
 407                 u32 value;
 408                 u32 chn_id = be32_to_cpu(*list++);
 409                 u32 chn_config = be32_to_cpu(*list++);
 410
 411                 /* Channel 0 and 1 are software channels */
 412                 if (chn_id < 2)
 413                         continue;
 414
 415                 writel_relaxed(chn_config, sadi->base +
 416                                REG_ADI_CHN_ADDR(chn_id));
 417
 418                 if (chn_id < 32) {
 419                         value = readl_relaxed(sadi->base + REG_ADI_CHN_EN);
 420                         value |= BIT(chn_id);
 421                         writel_relaxed(value, sadi->base + REG_ADI_CHN_EN);
 422                 } else if (chn_id < ADI_HW_CHNS) {
 423                         value = readl_relaxed(sadi->base + REG_ADI_CHN_EN1);
 424                         value |= BIT(chn_id - 32);
 425                         writel_relaxed(value, sadi->base + REG_ADI_CHN_EN1);
 426                 }
 427         }
 428 }
 429
 430 static int sprd_adi_probe(struct platform_device *pdev)
 431 {
 432         struct device_node *np = pdev->dev.of_node;
 433         struct spi_controller *ctlr;
 434         struct sprd_adi *sadi;
 435         struct resource *res;
 436         u32 num_chipselect;
 437         int ret;
 438
 439         if (!np) {
 440                 dev_err(&pdev->dev, "can not find the adi bus node\n");
 441                 return -ENODEV;
 442         }
 443
 444         pdev->id = of_alias_get_id(np, "spi");
 445         num_chipselect = of_get_child_count(np);
 446
 447         ctlr = spi_alloc_master(&pdev->dev, sizeof(struct sprd_adi));
 448         if (!ctlr)
 449                 return -ENOMEM;
 450
 451         dev_set_drvdata(&pdev->dev, ctlr);
 452         sadi = spi_controller_get_devdata(ctlr);
 453
 454         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 455         sadi->base = devm_ioremap_resource(&pdev->dev, res);
 456         if (IS_ERR(sadi->base)) {
 457                 ret = PTR_ERR(sadi->base);
 458                 goto put_ctlr;
 459         }
 460
 461         sadi->slave_vbase = (unsigned long)sadi->base + ADI_SLAVE_OFFSET;
 462         sadi->slave_pbase = res->start + ADI_SLAVE_OFFSET;
 463         sadi->ctlr = ctlr;
 464         sadi->dev = &pdev->dev;
 465         ret = of_hwspin_lock_get_id_byname(np, "adi");
 466         if (ret < 0) {
 467                 dev_err(&pdev->dev, "can not get the hardware spinlock\n");
 468                 goto put_ctlr;
 469         }
 470
 471         sadi->hwlock = devm_hwspin_lock_request_specific(&pdev->dev, ret);
 472         if (!sadi->hwlock) {
 473                 ret = -ENXIO;
 474                 goto put_ctlr;
 475         }
 476
 477         sprd_adi_hw_init(sadi);
 478
 479         ctlr->dev.of_node = pdev->dev.of_node;
 480         ctlr->bus_num = pdev->id;
 481         ctlr->num_chipselect = num_chipselect;
 482         ctlr->flags = SPI_MASTER_HALF_DUPLEX;
 483         ctlr->bits_per_word_mask = 0;
 484         ctlr->transfer_one = sprd_adi_transfer_one;
 485
 486         ret = devm_spi_register_controller(&pdev->dev, ctlr);
 487         if (ret) {
 488                 dev_err(&pdev->dev, "failed to register SPI controller\n");
 489                 goto put_ctlr;
 490         }
 491
 492         sadi->restart_handler.notifier_call = sprd_adi_restart_handler;
 493         sadi->restart_handler.priority = 128;
 494         ret = register_restart_handler(&sadi->restart_handler);
 495         if (ret) {
 496                 dev_err(&pdev->dev, "can not register restart handler\n");
 497                 goto put_ctlr;
 498         }
 499
 500         return 0;
 501
 502 put_ctlr:
 503         spi_controller_put(ctlr);
 504         return ret;
 505 }
 506
 507 static int sprd_adi_remove(struct platform_device *pdev)
 508 {
 509         struct spi_controller *ctlr = dev_get_drvdata(&pdev->dev);
 510         struct sprd_adi *sadi = spi_controller_get_devdata(ctlr);
 511
 512         unregister_restart_handler(&sadi->restart_handler);
 513         return 0;
 514 }
 515
 516 static const struct of_device_id sprd_adi_of_match[] = {
 517         {
 518                 .compatible = "sprd,sc9860-adi",
 519         },
 520         { },
 521 };
 522 MODULE_DEVICE_TABLE(of, sprd_adi_of_match);
 523
 524 static struct platform_driver sprd_adi_driver = {
 525         .driver = {
 526                 .name = "sprd-adi",
 527                 .of_match_table = sprd_adi_of_match,
 528         },
 529         .probe = sprd_adi_probe,
 530         .remove = sprd_adi_remove,
 531 };
 532 module_platform_driver(sprd_adi_driver);
 533
 534 MODULE_DESCRIPTION("Spreadtrum ADI Controller Driver");
 535 MODULE_AUTHOR("Baolin Wang <Baolin.Wang@spreadtrum.com>");
 536 MODULE_LICENSE("GPL v2");