arch/powerpc/sysdev/tsi108_pci.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * Common routines for Tundra Semiconductor TSI108 host bridge.
   4  *
   5  * 2004-2005 (c) Tundra Semiconductor Corp.
   6  * Author: Alex Bounine (alexandreb@tundra.com)
   7  * Author: Roy Zang (tie-fei.zang@freescale.com)
   8  *         Add pci interrupt router host
   9  */
  10
  11 #include <linux/kernel.h>
  12 #include <linux/init.h>
  13 #include <linux/pci.h>
  14 #include <linux/irq.h>
  15 #include <linux/interrupt.h>
  16
  17 #include <asm/byteorder.h>
  18 #include <asm/io.h>
  19 #include <asm/irq.h>
  20 #include <linux/uaccess.h>
  21 #include <asm/machdep.h>
  22 #include <asm/pci-bridge.h>
  23 #include <asm/tsi108.h>
  24 #include <asm/tsi108_pci.h>
  25 #include <asm/tsi108_irq.h>
  26 #include <asm/prom.h>
  27
  28 #undef DEBUG
  29 #ifdef DEBUG
  30 #define DBG(x...) printk(x)
  31 #else
  32 #define DBG(x...)
  33 #endif
  34
  35 #define tsi_mk_config_addr(bus, devfunc, offset) \
  36         ((((bus)<<16) | ((devfunc)<<8) | (offset & 0xfc)) + tsi108_pci_cfg_base)
  37
  38 u32 tsi108_pci_cfg_base;
  39 static u32 tsi108_pci_cfg_phys;
  40 u32 tsi108_csr_vir_base;
  41 static struct irq_domain *pci_irq_host;
  42
  43 extern u32 get_vir_csrbase(void);
  44 extern u32 tsi108_read_reg(u32 reg_offset);
  45 extern void tsi108_write_reg(u32 reg_offset, u32 val);
  46
  47 int
  48 tsi108_direct_write_config(struct pci_bus *bus, unsigned int devfunc,
  49                            int offset, int len, u32 val)
  50 {
  51         volatile unsigned char *cfg_addr;
  52         struct pci_controller *hose = pci_bus_to_host(bus);
  53
  54         if (ppc_md.pci_exclude_device)
  55                 if (ppc_md.pci_exclude_device(hose, bus->number, devfunc))
  56                         return PCIBIOS_DEVICE_NOT_FOUND;
  57
  58         cfg_addr = (unsigned char *)(tsi_mk_config_addr(bus->number,
  59                                                         devfunc, offset) |
  60                                                         (offset & 0x03));
  61
  62 #ifdef DEBUG
  63         printk("PCI CFG write : ");
  64         printk("%d:0x%x:0x%x ", bus->number, devfunc, offset);
  65         printk("%d ADDR=0x%08x ", len, (uint) cfg_addr);
  66         printk("data = 0x%08x\n", val);
  67 #endif
  68
  69         switch (len) {
  70         case 1:
  71                 out_8((u8 *) cfg_addr, val);
  72                 break;
  73         case 2:
  74                 out_le16((u16 *) cfg_addr, val);
  75                 break;
  76         default:
  77                 out_le32((u32 *) cfg_addr, val);
  78                 break;
  79         }
  80
  81         return PCIBIOS_SUCCESSFUL;
  82 }
  83
  84 void tsi108_clear_pci_error(u32 pci_cfg_base)
  85 {
  86         u32 err_stat, err_addr, pci_stat;
  87
  88         /*
  89          * Quietly clear PB and PCI error flags set as result
  90          * of PCI/X configuration read requests.
  91          */
  92
  93         /* Read PB Error Log Registers */
  94
  95         err_stat = tsi108_read_reg(TSI108_PB_OFFSET + TSI108_PB_ERRCS);
  96         err_addr = tsi108_read_reg(TSI108_PB_OFFSET + TSI108_PB_AERR);
  97
  98         if (err_stat & TSI108_PB_ERRCS_ES) {
  99                 /* Clear error flag */
 100                 tsi108_write_reg(TSI108_PB_OFFSET + TSI108_PB_ERRCS,
 101                                  TSI108_PB_ERRCS_ES);
 102
 103                 /* Clear read error reported in PB_ISR */
 104                 tsi108_write_reg(TSI108_PB_OFFSET + TSI108_PB_ISR,
 105                                  TSI108_PB_ISR_PBS_RD_ERR);
 106
 107                 /* Clear PCI/X bus cfg errors if applicable */
 108                 if ((err_addr & 0xFF000000) == pci_cfg_base) {
 109                         pci_stat =
 110                             tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_CSR);
 111                         tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_CSR,
 112                                          pci_stat);
 113                 }
 114         }
 115
 116         return;
 117 }
 118
 119 #define __tsi108_read_pci_config(x, addr, op)           \
 120         __asm__ __volatile__(                           \
 121                 "       "op" %0,0,%1\n"         \
 122                 "1:     eieio\n"                        \
 123                 "2:\n"                                  \
 124                 ".section .fixup,\"ax\"\n"              \
 125                 "3:     li %0,-1\n"                     \
 126                 "       b 2b\n"                         \
 127                 ".previous\n"                           \
 128                 EX_TABLE(1b, 3b)                        \
 129                 : "=r"(x) : "r"(addr))
 130
 131 int
 132 tsi108_direct_read_config(struct pci_bus *bus, unsigned int devfn, int offset,
 133                           int len, u32 * val)
 134 {
 135         volatile unsigned char *cfg_addr;
 136         struct pci_controller *hose = pci_bus_to_host(bus);
 137         u32 temp;
 138
 139         if (ppc_md.pci_exclude_device)
 140                 if (ppc_md.pci_exclude_device(hose, bus->number, devfn))
 141                         return PCIBIOS_DEVICE_NOT_FOUND;
 142
 143         cfg_addr = (unsigned char *)(tsi_mk_config_addr(bus->number,
 144                                                         devfn,
 145                                                         offset) | (offset &
 146                                                                    0x03));
 147
 148         switch (len) {
 149         case 1:
 150                 __tsi108_read_pci_config(temp, cfg_addr, "lbzx");
 151                 break;
 152         case 2:
 153                 __tsi108_read_pci_config(temp, cfg_addr, "lhbrx");
 154                 break;
 155         default:
 156                 __tsi108_read_pci_config(temp, cfg_addr, "lwbrx");
 157                 break;
 158         }
 159
 160         *val = temp;
 161
 162 #ifdef DEBUG
 163         if ((0xFFFFFFFF != temp) && (0xFFFF != temp) && (0xFF != temp)) {
 164                 printk("PCI CFG read : ");
 165                 printk("%d:0x%x:0x%x ", bus->number, devfn, offset);
 166                 printk("%d ADDR=0x%08x ", len, (uint) cfg_addr);
 167                 printk("data = 0x%x\n", *val);
 168         }
 169 #endif
 170         return PCIBIOS_SUCCESSFUL;
 171 }
 172
 173 void tsi108_clear_pci_cfg_error(void)
 174 {
 175         tsi108_clear_pci_error(tsi108_pci_cfg_phys);
 176 }
 177
 178 static struct pci_ops tsi108_direct_pci_ops = {
 179         .read = tsi108_direct_read_config,
 180         .write = tsi108_direct_write_config,
 181 };
 182
 183 int __init tsi108_setup_pci(struct device_node *dev, u32 cfg_phys, int primary)
 184 {
 185         int len;
 186         struct pci_controller *hose;
 187         struct resource rsrc;
 188         const int *bus_range;
 189         int has_address = 0;
 190
 191         /* PCI Config mapping */
 192         tsi108_pci_cfg_base = (u32)ioremap(cfg_phys, TSI108_PCI_CFG_SIZE);
 193         tsi108_pci_cfg_phys = cfg_phys;
 194         DBG("TSI_PCI: %s tsi108_pci_cfg_base=0x%x\n", __func__,
 195             tsi108_pci_cfg_base);
 196
 197         /* Fetch host bridge registers address */
 198         has_address = (of_address_to_resource(dev, 0, &rsrc) == 0);
 199
 200         /* Get bus range if any */
 201         bus_range = of_get_property(dev, "bus-range", &len);
 202         if (bus_range == NULL || len < 2 * sizeof(int)) {
 203                 printk(KERN_WARNING "Can't get bus-range for %pOF, assume"
 204                        " bus 0\n", dev);
 205         }
 206
 207         hose = pcibios_alloc_controller(dev);
 208
 209         if (!hose) {
 210                 printk("PCI Host bridge init failed\n");
 211                 return -ENOMEM;
 212         }
 213
 214         hose->first_busno = bus_range ? bus_range[0] : 0;
 215         hose->last_busno = bus_range ? bus_range[1] : 0xff;
 216
 217         (hose)->ops = &tsi108_direct_pci_ops;
 218
 219         printk(KERN_INFO "Found tsi108 PCI host bridge at 0x%08x. "
 220                "Firmware bus number: %d->%d\n",
 221                rsrc.start, hose->first_busno, hose->last_busno);
 222
 223         /* Interpret the "ranges" property */
 224         /* This also maps the I/O region and sets isa_io/mem_base */
 225         pci_process_bridge_OF_ranges(hose, dev, primary);
 226         return 0;
 227 }
 228
 229 /*
 230  * Low level utility functions
 231  */
 232
 233 static void tsi108_pci_int_mask(u_int irq)
 234 {
 235         u_int irp_cfg;
 236         int int_line = (irq - IRQ_PCI_INTAD_BASE);
 237
 238         irp_cfg = tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL);
 239         mb();
 240         irp_cfg |= (1 << int_line);     /* INTx_DIR = output */
 241         irp_cfg &= ~(3 << (8 + (int_line * 2)));        /* INTx_TYPE = unused */
 242         tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL, irp_cfg);
 243         mb();
 244         irp_cfg = tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL);
 245 }
 246
 247 static void tsi108_pci_int_unmask(u_int irq)
 248 {
 249         u_int irp_cfg;
 250         int int_line = (irq - IRQ_PCI_INTAD_BASE);
 251
 252         irp_cfg = tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL);
 253         mb();
 254         irp_cfg &= ~(1 << int_line);
 255         irp_cfg |= (3 << (8 + (int_line * 2)));
 256         tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL, irp_cfg);
 257         mb();
 258 }
 259
 260 static void init_pci_source(void)
 261 {
 262         tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL,
 263                         0x0000ff00);
 264         tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE,
 265                         TSI108_PCI_IRP_ENABLE_P_INT);
 266         mb();
 267 }
 268
 269 static inline unsigned int get_pci_source(void)
 270 {
 271         u_int temp = 0;
 272         int irq = -1;
 273         int i;
 274         u_int pci_irp_stat;
 275         static int mask = 0;
 276
 277         /* Read PCI/X block interrupt status register */
 278         pci_irp_stat = tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_STAT);
 279         mb();
 280
 281         if (pci_irp_stat & TSI108_PCI_IRP_STAT_P_INT) {
 282                 /* Process Interrupt from PCI bus INTA# - INTD# lines */
 283                 temp =
 284                     tsi108_read_reg(TSI108_PCI_OFFSET +
 285                                     TSI108_PCI_IRP_INTAD) & 0xf;
 286                 mb();
 287                 for (i = 0; i < 4; i++, mask++) {
 288                         if (temp & (1 << mask % 4)) {
 289                                 irq = IRQ_PCI_INTA + mask % 4;
 290                                 mask++;
 291                                 break;
 292                         }
 293                 }
 294
 295                 /* Disable interrupts from PCI block */
 296                 temp = tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE);
 297                 tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE,
 298                                 temp & ~TSI108_PCI_IRP_ENABLE_P_INT);
 299                 mb();
 300                 (void)tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE);
 301                 mb();
 302         }
 303 #ifdef DEBUG
 304         else {
 305                 printk("TSI108_PIC: error in TSI108_PCI_IRP_STAT\n");
 306                 pci_irp_stat =
 307                     tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_STAT);
 308                 temp =
 309                     tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_INTAD);
 310                 mb();
 311                 printk(">> stat=0x%08x intad=0x%08x ", pci_irp_stat, temp);
 312                 temp =
 313                     tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_CFG_CTL);
 314                 mb();
 315                 printk("cfg_ctl=0x%08x ", temp);
 316                 temp =
 317                     tsi108_read_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE);
 318                 mb();
 319                 printk("irp_enable=0x%08x\n", temp);
 320         }
 321 #endif  /* end of DEBUG */
 322
 323         return irq;
 324 }
 325
 326
 327 /*
 328  * Linux descriptor level callbacks
 329  */
 330
 331 static void tsi108_pci_irq_unmask(struct irq_data *d)
 332 {
 333         tsi108_pci_int_unmask(d->irq);
 334
 335         /* Enable interrupts from PCI block */
 336         tsi108_write_reg(TSI108_PCI_OFFSET + TSI108_PCI_IRP_ENABLE,
 337                          tsi108_read_reg(TSI108_PCI_OFFSET +
 338                                          TSI108_PCI_IRP_ENABLE) |
 339                          TSI108_PCI_IRP_ENABLE_P_INT);
 340         mb();
 341 }
 342
 343 static void tsi108_pci_irq_mask(struct irq_data *d)
 344 {
 345         tsi108_pci_int_mask(d->irq);
 346 }
 347
 348 static void tsi108_pci_irq_ack(struct irq_data *d)
 349 {
 350         tsi108_pci_int_mask(d->irq);
 351 }
 352
 353 /*
 354  * Interrupt controller descriptor for cascaded PCI interrupt controller.
 355  */
 356
 357 static struct irq_chip tsi108_pci_irq = {
 358         .name = "tsi108_PCI_int",
 359         .irq_mask = tsi108_pci_irq_mask,
 360         .irq_ack = tsi108_pci_irq_ack,
 361         .irq_unmask = tsi108_pci_irq_unmask,
 362 };
 363
 364 static int pci_irq_host_xlate(struct irq_domain *h, struct device_node *ct,
 365                             const u32 *intspec, unsigned int intsize,
 366                             irq_hw_number_t *out_hwirq, unsigned int *out_flags)
 367 {
 368         *out_hwirq = intspec[0];
 369         *out_flags = IRQ_TYPE_LEVEL_HIGH;
 370         return 0;
 371 }
 372
 373 static int pci_irq_host_map(struct irq_domain *h, unsigned int virq,
 374                           irq_hw_number_t hw)
 375 {       unsigned int irq;
 376         DBG("%s(%d, 0x%lx)\n", __func__, virq, hw);
 377         if ((virq >= 1) && (virq <= 4)){
 378                 irq = virq + IRQ_PCI_INTAD_BASE - 1;
 379                 irq_set_status_flags(irq, IRQ_LEVEL);
 380                 irq_set_chip(irq, &tsi108_pci_irq);
 381         }
 382         return 0;
 383 }
 384
 385 static const struct irq_domain_ops pci_irq_domain_ops = {
 386         .map = pci_irq_host_map,
 387         .xlate = pci_irq_host_xlate,
 388 };
 389
 390 /*
 391  * Exported functions
 392  */
 393
 394 /*
 395  * The Tsi108 PCI interrupts initialization routine.
 396  *
 397  * The INTA# - INTD# interrupts on the PCI bus are reported by the PCI block
 398  * to the MPIC using single interrupt source (IRQ_TSI108_PCI). Therefore the
 399  * PCI block has to be treated as a cascaded interrupt controller connected
 400  * to the MPIC.
 401  */
 402
 403 void __init tsi108_pci_int_init(struct device_node *node)
 404 {
 405         DBG("Tsi108_pci_int_init: initializing PCI interrupts\n");
 406
 407         pci_irq_host = irq_domain_add_legacy_isa(node, &pci_irq_domain_ops, NULL);
 408         if (pci_irq_host == NULL) {
 409                 printk(KERN_ERR "pci_irq_host: failed to allocate irq domain!\n");
 410                 return;
 411         }
 412
 413         init_pci_source();
 414 }
 415
 416 void tsi108_irq_cascade(struct irq_desc *desc)
 417 {
 418         struct irq_chip *chip = irq_desc_get_chip(desc);
 419         unsigned int cascade_irq = get_pci_source();
 420
 421         if (cascade_irq)
 422                 generic_handle_irq(cascade_irq);
 423
 424         chip->irq_eoi(&desc->irq_data);
 425 }