?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
iwlwifi: introduce host commands callbacks
[linux/fpc-iii.git] / drivers / usb / gadget / file_storage.c
blob017a196d041fe58d9617aa2c52148c9f3b258e64
1 /*
2 * file_storage.c -- File-backed USB Storage Gadget, for USB development
3 *
4 * Copyright (C) 2003-2007 Alan Stern
5 * All rights reserved.
6 *
7 * Redistribution and use in source and binary forms, with or without
8 * modification, are permitted provided that the following conditions
9 * are met:
10 * 1. Redistributions of source code must retain the above copyright
11 * notice, this list of conditions, and the following disclaimer,
12 * without modification.
13 * 2. Redistributions in binary form must reproduce the above copyright
14 * notice, this list of conditions and the following disclaimer in the
15 * documentation and/or other materials provided with the distribution.
16 * 3. The names of the above-listed copyright holders may not be used
17 * to endorse or promote products derived from this software without
18 * specific prior written permission.
19 *
20 * ALTERNATIVELY, this software may be distributed under the terms of the
21 * GNU General Public License ("GPL") as published by the Free Software
22 * Foundation, either version 2 of that License or (at your option) any
23 * later version.
24 *
25 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
26 * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
27 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
28 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
29 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
30 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
31 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
32 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
33 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
34 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
35 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
36 */
37
38
39 /*
40 * The File-backed Storage Gadget acts as a USB Mass Storage device,
41 * appearing to the host as a disk drive. In addition to providing an
42 * example of a genuinely useful gadget driver for a USB device, it also
43 * illustrates a technique of double-buffering for increased throughput.
44 * Last but not least, it gives an easy way to probe the behavior of the
45 * Mass Storage drivers in a USB host.
46 *
47 * Backing storage is provided by a regular file or a block device, specified
48 * by the "file" module parameter. Access can be limited to read-only by
49 * setting the optional "ro" module parameter. The gadget will indicate that
50 * it has removable media if the optional "removable" module parameter is set.
51 *
52 * The gadget supports the Control-Bulk (CB), Control-Bulk-Interrupt (CBI),
53 * and Bulk-Only (also known as Bulk-Bulk-Bulk or BBB) transports, selected
54 * by the optional "transport" module parameter. It also supports the
55 * following protocols: RBC (0x01), ATAPI or SFF-8020i (0x02), QIC-157 (0c03),
56 * UFI (0x04), SFF-8070i (0x05), and transparent SCSI (0x06), selected by
57 * the optional "protocol" module parameter. In addition, the default
58 * Vendor ID, Product ID, and release number can be overridden.
59 *
60 * There is support for multiple logical units (LUNs), each of which has
61 * its own backing file. The number of LUNs can be set using the optional
62 * "luns" module parameter (anywhere from 1 to 8), and the corresponding
63 * files are specified using comma-separated lists for "file" and "ro".
64 * The default number of LUNs is taken from the number of "file" elements;
65 * it is 1 if "file" is not given. If "removable" is not set then a backing
66 * file must be specified for each LUN. If it is set, then an unspecified
67 * or empty backing filename means the LUN's medium is not loaded.
68 *
69 * Requirements are modest; only a bulk-in and a bulk-out endpoint are
70 * needed (an interrupt-out endpoint is also needed for CBI). The memory
71 * requirement amounts to two 16K buffers, size configurable by a parameter.
72 * Support is included for both full-speed and high-speed operation.
73 *
74 * Note that the driver is slightly non-portable in that it assumes a
75 * single memory/DMA buffer will be useable for bulk-in, bulk-out, and
76 * interrupt-in endpoints. With most device controllers this isn't an
77 * issue, but there may be some with hardware restrictions that prevent
78 * a buffer from being used by more than one endpoint.
79 *
80 * Module options:
81 *
82 * file=filename[,filename...]
83 * Required if "removable" is not set, names of
84 * the files or block devices used for
85 * backing storage
86 * ro=b[,b...] Default false, booleans for read-only access
87 * removable Default false, boolean for removable media
88 * luns=N Default N = number of filenames, number of
89 * LUNs to support
90 * stall Default determined according to the type of
91 * USB device controller (usually true),
92 * boolean to permit the driver to halt
93 * bulk endpoints
94 * transport=XXX Default BBB, transport name (CB, CBI, or BBB)
95 * protocol=YYY Default SCSI, protocol name (RBC, 8020 or
96 * ATAPI, QIC, UFI, 8070, or SCSI;
97 * also 1 - 6)
98 * vendor=0xVVVV Default 0x0525 (NetChip), USB Vendor ID
99 * product=0xPPPP Default 0xa4a5 (FSG), USB Product ID
100 * release=0xRRRR Override the USB release number (bcdDevice)
101 * buflen=N Default N=16384, buffer size used (will be
102 * rounded down to a multiple of
103 * PAGE_CACHE_SIZE)
104 *
105 * If CONFIG_USB_FILE_STORAGE_TEST is not set, only the "file", "ro",
106 * "removable", "luns", and "stall" options are available; default values
107 * are used for everything else.
108 *
109 * The pathnames of the backing files and the ro settings are available in
110 * the attribute files "file" and "ro" in the lun<n> subdirectory of the
111 * gadget's sysfs directory. If the "removable" option is set, writing to
112 * these files will simulate ejecting/loading the medium (writing an empty
113 * line means eject) and adjusting a write-enable tab. Changes to the ro
114 * setting are not allowed when the medium is loaded.
115 *
116 * This gadget driver is heavily based on "Gadget Zero" by David Brownell.
117 * The driver's SCSI command interface was based on the "Information
118 * technology - Small Computer System Interface - 2" document from
119 * X3T9.2 Project 375D, Revision 10L, 7-SEP-93, available at
120 * <http://www.t10.org/ftp/t10/drafts/s2/s2-r10l.pdf>. The single exception
121 * is opcode 0x23 (READ FORMAT CAPACITIES), which was based on the
122 * "Universal Serial Bus Mass Storage Class UFI Command Specification"
123 * document, Revision 1.0, December 14, 1998, available at
124 * <http://www.usb.org/developers/devclass_docs/usbmass-ufi10.pdf>.
125 */
126
127
128 /*
129 * Driver Design
130 *
131 * The FSG driver is fairly straightforward. There is a main kernel
132 * thread that handles most of the work. Interrupt routines field
133 * callbacks from the controller driver: bulk- and interrupt-request
134 * completion notifications, endpoint-0 events, and disconnect events.
135 * Completion events are passed to the main thread by wakeup calls. Many
136 * ep0 requests are handled at interrupt time, but SetInterface,
137 * SetConfiguration, and device reset requests are forwarded to the
138 * thread in the form of "exceptions" using SIGUSR1 signals (since they
139 * should interrupt any ongoing file I/O operations).
140 *
141 * The thread's main routine implements the standard command/data/status
142 * parts of a SCSI interaction. It and its subroutines are full of tests
143 * for pending signals/exceptions -- all this polling is necessary since
144 * the kernel has no setjmp/longjmp equivalents. (Maybe this is an
145 * indication that the driver really wants to be running in userspace.)
146 * An important point is that so long as the thread is alive it keeps an
147 * open reference to the backing file. This will prevent unmounting
148 * the backing file's underlying filesystem and could cause problems
149 * during system shutdown, for example. To prevent such problems, the
150 * thread catches INT, TERM, and KILL signals and converts them into
151 * an EXIT exception.
152 *
153 * In normal operation the main thread is started during the gadget's
154 * fsg_bind() callback and stopped during fsg_unbind(). But it can also
155 * exit when it receives a signal, and there's no point leaving the
156 * gadget running when the thread is dead. So just before the thread
157 * exits, it deregisters the gadget driver. This makes things a little
158 * tricky: The driver is deregistered at two places, and the exiting
159 * thread can indirectly call fsg_unbind() which in turn can tell the
160 * thread to exit. The first problem is resolved through the use of the
161 * REGISTERED atomic bitflag; the driver will only be deregistered once.
162 * The second problem is resolved by having fsg_unbind() check
163 * fsg->state; it won't try to stop the thread if the state is already
164 * FSG_STATE_TERMINATED.
165 *
166 * To provide maximum throughput, the driver uses a circular pipeline of
167 * buffer heads (struct fsg_buffhd). In principle the pipeline can be
168 * arbitrarily long; in practice the benefits don't justify having more
169 * than 2 stages (i.e., double buffering). But it helps to think of the
170 * pipeline as being a long one. Each buffer head contains a bulk-in and
171 * a bulk-out request pointer (since the buffer can be used for both
172 * output and input -- directions always are given from the host's
173 * point of view) as well as a pointer to the buffer and various state
174 * variables.
175 *
176 * Use of the pipeline follows a simple protocol. There is a variable
177 * (fsg->next_buffhd_to_fill) that points to the next buffer head to use.
178 * At any time that buffer head may still be in use from an earlier
179 * request, so each buffer head has a state variable indicating whether
180 * it is EMPTY, FULL, or BUSY. Typical use involves waiting for the
181 * buffer head to be EMPTY, filling the buffer either by file I/O or by
182 * USB I/O (during which the buffer head is BUSY), and marking the buffer
183 * head FULL when the I/O is complete. Then the buffer will be emptied
184 * (again possibly by USB I/O, during which it is marked BUSY) and
185 * finally marked EMPTY again (possibly by a completion routine).
186 *
187 * A module parameter tells the driver to avoid stalling the bulk
188 * endpoints wherever the transport specification allows. This is
189 * necessary for some UDCs like the SuperH, which cannot reliably clear a
190 * halt on a bulk endpoint. However, under certain circumstances the
191 * Bulk-only specification requires a stall. In such cases the driver
192 * will halt the endpoint and set a flag indicating that it should clear
193 * the halt in software during the next device reset. Hopefully this
194 * will permit everything to work correctly. Furthermore, although the
195 * specification allows the bulk-out endpoint to halt when the host sends
196 * too much data, implementing this would cause an unavoidable race.
197 * The driver will always use the "no-stall" approach for OUT transfers.
198 *
199 * One subtle point concerns sending status-stage responses for ep0
200 * requests. Some of these requests, such as device reset, can involve
201 * interrupting an ongoing file I/O operation, which might take an
202 * arbitrarily long time. During that delay the host might give up on
203 * the original ep0 request and issue a new one. When that happens the
204 * driver should not notify the host about completion of the original
205 * request, as the host will no longer be waiting for it. So the driver
206 * assigns to each ep0 request a unique tag, and it keeps track of the
207 * tag value of the request associated with a long-running exception
208 * (device-reset, interface-change, or configuration-change). When the
209 * exception handler is finished, the status-stage response is submitted
210 * only if the current ep0 request tag is equal to the exception request
211 * tag. Thus only the most recently received ep0 request will get a
212 * status-stage response.
213 *
214 * Warning: This driver source file is too long. It ought to be split up
215 * into a header file plus about 3 separate .c files, to handle the details
216 * of the Gadget, USB Mass Storage, and SCSI protocols.
217 */
218
219
220 /* #define VERBOSE_DEBUG */
221 /* #define DUMP_MSGS */
222
223
224 #include <linux/blkdev.h>
225 #include <linux/completion.h>
226 #include <linux/dcache.h>
227 #include <linux/delay.h>
228 #include <linux/device.h>
229 #include <linux/fcntl.h>
230 #include <linux/file.h>
231 #include <linux/fs.h>
232 #include <linux/kref.h>
233 #include <linux/kthread.h>
234 #include <linux/limits.h>
235 #include <linux/rwsem.h>
236 #include <linux/slab.h>
237 #include <linux/spinlock.h>
238 #include <linux/string.h>
239 #include <linux/freezer.h>
240 #include <linux/utsname.h>
241
242 #include <linux/usb/ch9.h>
243 #include <linux/usb/gadget.h>
244
245 #include "gadget_chips.h"
246
247
248 /*-------------------------------------------------------------------------*/
249
250 #define DRIVER_DESC "File-backed Storage Gadget"
251 #define DRIVER_NAME "g_file_storage"
252 #define DRIVER_VERSION "7 August 2007"
253
254 static const char longname[] = DRIVER_DESC;
255 static const char shortname[] = DRIVER_NAME;
256
257 MODULE_DESCRIPTION(DRIVER_DESC);
258 MODULE_AUTHOR("Alan Stern");
259 MODULE_LICENSE("Dual BSD/GPL");
260
261 /* Thanks to NetChip Technologies for donating this product ID.
262 *
263 * DO NOT REUSE THESE IDs with any other driver!! Ever!!
264 * Instead: allocate your own, using normal USB-IF procedures. */
265 #define DRIVER_VENDOR_ID 0x0525 // NetChip
266 #define DRIVER_PRODUCT_ID 0xa4a5 // Linux-USB File-backed Storage Gadget
267
268
269 /*
270 * This driver assumes self-powered hardware and has no way for users to
271 * trigger remote wakeup. It uses autoconfiguration to select endpoints
272 * and endpoint addresses.
273 */
274
275
276 /*-------------------------------------------------------------------------*/
277
278 #define LDBG(lun,fmt,args...) \
279 dev_dbg(&(lun)->dev , fmt , ## args)
280 #define MDBG(fmt,args...) \
281 pr_debug(DRIVER_NAME ": " fmt , ## args)
282
283 #ifndef DEBUG
284 #undef VERBOSE_DEBUG
285 #undef DUMP_MSGS
286 #endif /* !DEBUG */
287
288 #ifdef VERBOSE_DEBUG
289 #define VLDBG LDBG
290 #else
291 #define VLDBG(lun,fmt,args...) \
292 do { } while (0)
293 #endif /* VERBOSE_DEBUG */
294
295 #define LERROR(lun,fmt,args...) \
296 dev_err(&(lun)->dev , fmt , ## args)
297 #define LWARN(lun,fmt,args...) \
298 dev_warn(&(lun)->dev , fmt , ## args)
299 #define LINFO(lun,fmt,args...) \
300 dev_info(&(lun)->dev , fmt , ## args)
301
302 #define MINFO(fmt,args...) \
303 pr_info(DRIVER_NAME ": " fmt , ## args)
304
305 #define DBG(d, fmt, args...) \
306 dev_dbg(&(d)->gadget->dev , fmt , ## args)
307 #define VDBG(d, fmt, args...) \
308 dev_vdbg(&(d)->gadget->dev , fmt , ## args)
309 #define ERROR(d, fmt, args...) \
310 dev_err(&(d)->gadget->dev , fmt , ## args)
311 #define WARN(d, fmt, args...) \
312 dev_warn(&(d)->gadget->dev , fmt , ## args)
313 #define INFO(d, fmt, args...) \
314 dev_info(&(d)->gadget->dev , fmt , ## args)
315
316
317 /*-------------------------------------------------------------------------*/
318
319 /* Encapsulate the module parameter settings */
320
321 #define MAX_LUNS 8
322
323 static struct {
324 char *file[MAX_LUNS];
325 int ro[MAX_LUNS];
326 unsigned int num_filenames;
327 unsigned int num_ros;
328 unsigned int nluns;
329
330 int removable;
331 int can_stall;
332
333 char *transport_parm;
334 char *protocol_parm;
335 unsigned short vendor;
336 unsigned short product;
337 unsigned short release;
338 unsigned int buflen;
339
340 int transport_type;
341 char *transport_name;
342 int protocol_type;
343 char *protocol_name;
344
345 } mod_data = { // Default values
346 .transport_parm = "BBB",
347 .protocol_parm = "SCSI",
348 .removable = 0,
349 .can_stall = 1,
350 .vendor = DRIVER_VENDOR_ID,
351 .product = DRIVER_PRODUCT_ID,
352 .release = 0xffff, // Use controller chip type
353 .buflen = 16384,
354 };
355
356
357 module_param_array_named(file, mod_data.file, charp, &mod_data.num_filenames,
358 S_IRUGO);
359 MODULE_PARM_DESC(file, "names of backing files or devices");
360
361 module_param_array_named(ro, mod_data.ro, bool, &mod_data.num_ros, S_IRUGO);
362 MODULE_PARM_DESC(ro, "true to force read-only");
363
364 module_param_named(luns, mod_data.nluns, uint, S_IRUGO);
365 MODULE_PARM_DESC(luns, "number of LUNs");
366
367 module_param_named(removable, mod_data.removable, bool, S_IRUGO);
368 MODULE_PARM_DESC(removable, "true to simulate removable media");
369
370 module_param_named(stall, mod_data.can_stall, bool, S_IRUGO);
371 MODULE_PARM_DESC(stall, "false to prevent bulk stalls");
372
373
374 /* In the non-TEST version, only the module parameters listed above
375 * are available. */
376 #ifdef CONFIG_USB_FILE_STORAGE_TEST
377
378 module_param_named(transport, mod_data.transport_parm, charp, S_IRUGO);
379 MODULE_PARM_DESC(transport, "type of transport (BBB, CBI, or CB)");
380
381 module_param_named(protocol, mod_data.protocol_parm, charp, S_IRUGO);
382 MODULE_PARM_DESC(protocol, "type of protocol (RBC, 8020, QIC, UFI, "
383 "8070, or SCSI)");
384
385 module_param_named(vendor, mod_data.vendor, ushort, S_IRUGO);
386 MODULE_PARM_DESC(vendor, "USB Vendor ID");
387
388 module_param_named(product, mod_data.product, ushort, S_IRUGO);
389 MODULE_PARM_DESC(product, "USB Product ID");
390
391 module_param_named(release, mod_data.release, ushort, S_IRUGO);
392 MODULE_PARM_DESC(release, "USB release number");
393
394 module_param_named(buflen, mod_data.buflen, uint, S_IRUGO);
395 MODULE_PARM_DESC(buflen, "I/O buffer size");
396
397 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
398
399
400 /*-------------------------------------------------------------------------*/
401
402 /* USB protocol value = the transport method */
403 #define USB_PR_CBI 0x00 // Control/Bulk/Interrupt
404 #define USB_PR_CB 0x01 // Control/Bulk w/o interrupt
405 #define USB_PR_BULK 0x50 // Bulk-only
406
407 /* USB subclass value = the protocol encapsulation */
408 #define USB_SC_RBC 0x01 // Reduced Block Commands (flash)
409 #define USB_SC_8020 0x02 // SFF-8020i, MMC-2, ATAPI (CD-ROM)
410 #define USB_SC_QIC 0x03 // QIC-157 (tape)
411 #define USB_SC_UFI 0x04 // UFI (floppy)
412 #define USB_SC_8070 0x05 // SFF-8070i (removable)
413 #define USB_SC_SCSI 0x06 // Transparent SCSI
414
415 /* Bulk-only data structures */
416
417 /* Command Block Wrapper */
418 struct bulk_cb_wrap {
419 __le32 Signature; // Contains 'USBC'
420 u32 Tag; // Unique per command id
421 __le32 DataTransferLength; // Size of the data
422 u8 Flags; // Direction in bit 7
423 u8 Lun; // LUN (normally 0)
424 u8 Length; // Of the CDB, <= MAX_COMMAND_SIZE
425 u8 CDB[16]; // Command Data Block
426 };
427
428 #define USB_BULK_CB_WRAP_LEN 31
429 #define USB_BULK_CB_SIG 0x43425355 // Spells out USBC
430 #define USB_BULK_IN_FLAG 0x80
431
432 /* Command Status Wrapper */
433 struct bulk_cs_wrap {
434 __le32 Signature; // Should = 'USBS'
435 u32 Tag; // Same as original command
436 __le32 Residue; // Amount not transferred
437 u8 Status; // See below
438 };
439
440 #define USB_BULK_CS_WRAP_LEN 13
441 #define USB_BULK_CS_SIG 0x53425355 // Spells out 'USBS'
442 #define USB_STATUS_PASS 0
443 #define USB_STATUS_FAIL 1
444 #define USB_STATUS_PHASE_ERROR 2
445
446 /* Bulk-only class specific requests */
447 #define USB_BULK_RESET_REQUEST 0xff
448 #define USB_BULK_GET_MAX_LUN_REQUEST 0xfe
449
450
451 /* CBI Interrupt data structure */
452 struct interrupt_data {
453 u8 bType;
454 u8 bValue;
455 };
456
457 #define CBI_INTERRUPT_DATA_LEN 2
458
459 /* CBI Accept Device-Specific Command request */
460 #define USB_CBI_ADSC_REQUEST 0x00
461
462
463 #define MAX_COMMAND_SIZE 16 // Length of a SCSI Command Data Block
464
465 /* SCSI commands that we recognize */
466 #define SC_FORMAT_UNIT 0x04
467 #define SC_INQUIRY 0x12
468 #define SC_MODE_SELECT_6 0x15
469 #define SC_MODE_SELECT_10 0x55
470 #define SC_MODE_SENSE_6 0x1a
471 #define SC_MODE_SENSE_10 0x5a
472 #define SC_PREVENT_ALLOW_MEDIUM_REMOVAL 0x1e
473 #define SC_READ_6 0x08
474 #define SC_READ_10 0x28
475 #define SC_READ_12 0xa8
476 #define SC_READ_CAPACITY 0x25
477 #define SC_READ_FORMAT_CAPACITIES 0x23
478 #define SC_RELEASE 0x17
479 #define SC_REQUEST_SENSE 0x03
480 #define SC_RESERVE 0x16
481 #define SC_SEND_DIAGNOSTIC 0x1d
482 #define SC_START_STOP_UNIT 0x1b
483 #define SC_SYNCHRONIZE_CACHE 0x35
484 #define SC_TEST_UNIT_READY 0x00
485 #define SC_VERIFY 0x2f
486 #define SC_WRITE_6 0x0a
487 #define SC_WRITE_10 0x2a
488 #define SC_WRITE_12 0xaa
489
490 /* SCSI Sense Key/Additional Sense Code/ASC Qualifier values */
491 #define SS_NO_SENSE 0
492 #define SS_COMMUNICATION_FAILURE 0x040800
493 #define SS_INVALID_COMMAND 0x052000
494 #define SS_INVALID_FIELD_IN_CDB 0x052400
495 #define SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE 0x052100
496 #define SS_LOGICAL_UNIT_NOT_SUPPORTED 0x052500
497 #define SS_MEDIUM_NOT_PRESENT 0x023a00
498 #define SS_MEDIUM_REMOVAL_PREVENTED 0x055302
499 #define SS_NOT_READY_TO_READY_TRANSITION 0x062800
500 #define SS_RESET_OCCURRED 0x062900
501 #define SS_SAVING_PARAMETERS_NOT_SUPPORTED 0x053900
502 #define SS_UNRECOVERED_READ_ERROR 0x031100
503 #define SS_WRITE_ERROR 0x030c02
504 #define SS_WRITE_PROTECTED 0x072700
505
506 #define SK(x) ((u8) ((x) >> 16)) // Sense Key byte, etc.
507 #define ASC(x) ((u8) ((x) >> 8))
508 #define ASCQ(x) ((u8) (x))
509
510
511 /*-------------------------------------------------------------------------*/
512
513 /*
514 * These definitions will permit the compiler to avoid generating code for
515 * parts of the driver that aren't used in the non-TEST version. Even gcc
516 * can recognize when a test of a constant expression yields a dead code
517 * path.
518 */
519
520 #ifdef CONFIG_USB_FILE_STORAGE_TEST
521
522 #define transport_is_bbb() (mod_data.transport_type == USB_PR_BULK)
523 #define transport_is_cbi() (mod_data.transport_type == USB_PR_CBI)
524 #define protocol_is_scsi() (mod_data.protocol_type == USB_SC_SCSI)
525
526 #else
527
528 #define transport_is_bbb() 1
529 #define transport_is_cbi() 0
530 #define protocol_is_scsi() 1
531
532 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
533
534
535 struct lun {
536 struct file *filp;
537 loff_t file_length;
538 loff_t num_sectors;
539
540 unsigned int ro : 1;
541 unsigned int prevent_medium_removal : 1;
542 unsigned int registered : 1;
543 unsigned int info_valid : 1;
544
545 u32 sense_data;
546 u32 sense_data_info;
547 u32 unit_attention_data;
548
549 struct device dev;
550 };
551
552 #define backing_file_is_open(curlun) ((curlun)->filp != NULL)
553
554 static struct lun *dev_to_lun(struct device *dev)
555 {
556 return container_of(dev, struct lun, dev);
557 }
558
559
560 /* Big enough to hold our biggest descriptor */
561 #define EP0_BUFSIZE 256
562 #define DELAYED_STATUS (EP0_BUFSIZE + 999) // An impossibly large value
563
564 /* Number of buffers we will use. 2 is enough for double-buffering */
565 #define NUM_BUFFERS 2
566
567 enum fsg_buffer_state {
568 BUF_STATE_EMPTY = 0,
569 BUF_STATE_FULL,
570 BUF_STATE_BUSY
571 };
572
573 struct fsg_buffhd {
574 void *buf;
575 enum fsg_buffer_state state;
576 struct fsg_buffhd *next;
577
578 /* The NetChip 2280 is faster, and handles some protocol faults
579 * better, if we don't submit any short bulk-out read requests.
580 * So we will record the intended request length here. */
581 unsigned int bulk_out_intended_length;
582
583 struct usb_request *inreq;
584 int inreq_busy;
585 struct usb_request *outreq;
586 int outreq_busy;
587 };
588
589 enum fsg_state {
590 FSG_STATE_COMMAND_PHASE = -10, // This one isn't used anywhere
591 FSG_STATE_DATA_PHASE,
592 FSG_STATE_STATUS_PHASE,
593
594 FSG_STATE_IDLE = 0,
595 FSG_STATE_ABORT_BULK_OUT,
596 FSG_STATE_RESET,
597 FSG_STATE_INTERFACE_CHANGE,
598 FSG_STATE_CONFIG_CHANGE,
599 FSG_STATE_DISCONNECT,
600 FSG_STATE_EXIT,
601 FSG_STATE_TERMINATED
602 };
603
604 enum data_direction {
605 DATA_DIR_UNKNOWN = 0,
606 DATA_DIR_FROM_HOST,
607 DATA_DIR_TO_HOST,
608 DATA_DIR_NONE
609 };
610
611 struct fsg_dev {
612 /* lock protects: state, all the req_busy's, and cbbuf_cmnd */
613 spinlock_t lock;
614 struct usb_gadget *gadget;
615
616 /* filesem protects: backing files in use */
617 struct rw_semaphore filesem;
618
619 /* reference counting: wait until all LUNs are released */
620 struct kref ref;
621
622 struct usb_ep *ep0; // Handy copy of gadget->ep0
623 struct usb_request *ep0req; // For control responses
624 unsigned int ep0_req_tag;
625 const char *ep0req_name;
626
627 struct usb_request *intreq; // For interrupt responses
628 int intreq_busy;
629 struct fsg_buffhd *intr_buffhd;
630
631 unsigned int bulk_out_maxpacket;
632 enum fsg_state state; // For exception handling
633 unsigned int exception_req_tag;
634
635 u8 config, new_config;
636
637 unsigned int running : 1;
638 unsigned int bulk_in_enabled : 1;
639 unsigned int bulk_out_enabled : 1;
640 unsigned int intr_in_enabled : 1;
641 unsigned int phase_error : 1;
642 unsigned int short_packet_received : 1;
643 unsigned int bad_lun_okay : 1;
644
645 unsigned long atomic_bitflags;
646 #define REGISTERED 0
647 #define CLEAR_BULK_HALTS 1
648 #define SUSPENDED 2
649
650 struct usb_ep *bulk_in;
651 struct usb_ep *bulk_out;
652 struct usb_ep *intr_in;
653
654 struct fsg_buffhd *next_buffhd_to_fill;
655 struct fsg_buffhd *next_buffhd_to_drain;
656 struct fsg_buffhd buffhds[NUM_BUFFERS];
657
658 int thread_wakeup_needed;
659 struct completion thread_notifier;
660 struct task_struct *thread_task;
661
662 int cmnd_size;
663 u8 cmnd[MAX_COMMAND_SIZE];
664 enum data_direction data_dir;
665 u32 data_size;
666 u32 data_size_from_cmnd;
667 u32 tag;
668 unsigned int lun;
669 u32 residue;
670 u32 usb_amount_left;
671
672 /* The CB protocol offers no way for a host to know when a command
673 * has completed. As a result the next command may arrive early,
674 * and we will still have to handle it. For that reason we need
675 * a buffer to store new commands when using CB (or CBI, which
676 * does not oblige a host to wait for command completion either). */
677 int cbbuf_cmnd_size;
678 u8 cbbuf_cmnd[MAX_COMMAND_SIZE];
679
680 unsigned int nluns;
681 struct lun *luns;
682 struct lun *curlun;
683 };
684
685 typedef void (*fsg_routine_t)(struct fsg_dev *);
686
687 static int exception_in_progress(struct fsg_dev *fsg)
688 {
689 return (fsg->state > FSG_STATE_IDLE);
690 }
691
692 /* Make bulk-out requests be divisible by the maxpacket size */
693 static void set_bulk_out_req_length(struct fsg_dev *fsg,
694 struct fsg_buffhd *bh, unsigned int length)
695 {
696 unsigned int rem;
697
698 bh->bulk_out_intended_length = length;
699 rem = length % fsg->bulk_out_maxpacket;
700 if (rem > 0)
701 length += fsg->bulk_out_maxpacket - rem;
702 bh->outreq->length = length;
703 }
704
705 static struct fsg_dev *the_fsg;
706 static struct usb_gadget_driver fsg_driver;
707
708 static void close_backing_file(struct lun *curlun);
709 static void close_all_backing_files(struct fsg_dev *fsg);
710
711
712 /*-------------------------------------------------------------------------*/
713
714 #ifdef DUMP_MSGS
715
716 static void dump_msg(struct fsg_dev *fsg, const char *label,
717 const u8 *buf, unsigned int length)
718 {
719 if (length < 512) {
720 DBG(fsg, "%s, length %u:\n", label, length);
721 print_hex_dump(KERN_DEBUG, "", DUMP_PREFIX_OFFSET,
722 16, 1, buf, length, 0);
723 }
724 }
725
726 static void dump_cdb(struct fsg_dev *fsg)
727 {}
728
729 #else
730
731 static void dump_msg(struct fsg_dev *fsg, const char *label,
732 const u8 *buf, unsigned int length)
733 {}
734
735 #ifdef VERBOSE_DEBUG
736
737 static void dump_cdb(struct fsg_dev *fsg)
738 {
739 print_hex_dump(KERN_DEBUG, "SCSI CDB: ", DUMP_PREFIX_NONE,
740 16, 1, fsg->cmnd, fsg->cmnd_size, 0);
741 }
742
743 #else
744
745 static void dump_cdb(struct fsg_dev *fsg)
746 {}
747
748 #endif /* VERBOSE_DEBUG */
749 #endif /* DUMP_MSGS */
750
751
752 static int fsg_set_halt(struct fsg_dev *fsg, struct usb_ep *ep)
753 {
754 const char *name;
755
756 if (ep == fsg->bulk_in)
757 name = "bulk-in";
758 else if (ep == fsg->bulk_out)
759 name = "bulk-out";
760 else
761 name = ep->name;
762 DBG(fsg, "%s set halt\n", name);
763 return usb_ep_set_halt(ep);
764 }
765
766
767 /*-------------------------------------------------------------------------*/
768
769 /* Routines for unaligned data access */
770
771 static u16 get_be16(u8 *buf)
772 {
773 return ((u16) buf[0] << 8) | ((u16) buf[1]);
774 }
775
776 static u32 get_be32(u8 *buf)
777 {
778 return ((u32) buf[0] << 24) | ((u32) buf[1] << 16) |
779 ((u32) buf[2] << 8) | ((u32) buf[3]);
780 }
781
782 static void put_be16(u8 *buf, u16 val)
783 {
784 buf[0] = val >> 8;
785 buf[1] = val;
786 }
787
788 static void put_be32(u8 *buf, u32 val)
789 {
790 buf[0] = val >> 24;
791 buf[1] = val >> 16;
792 buf[2] = val >> 8;
793 buf[3] = val & 0xff;
794 }
795
796
797 /*-------------------------------------------------------------------------*/
798
799 /*
800 * DESCRIPTORS ... most are static, but strings and (full) configuration
801 * descriptors are built on demand. Also the (static) config and interface
802 * descriptors are adjusted during fsg_bind().
803 */
804 #define STRING_MANUFACTURER 1
805 #define STRING_PRODUCT 2
806 #define STRING_SERIAL 3
807 #define STRING_CONFIG 4
808 #define STRING_INTERFACE 5
809
810 /* There is only one configuration. */
811 #define CONFIG_VALUE 1
812
813 static struct usb_device_descriptor
814 device_desc = {
815 .bLength = sizeof device_desc,
816 .bDescriptorType = USB_DT_DEVICE,
817
818 .bcdUSB = __constant_cpu_to_le16(0x0200),
819 .bDeviceClass = USB_CLASS_PER_INTERFACE,
820
821 /* The next three values can be overridden by module parameters */
822 .idVendor = __constant_cpu_to_le16(DRIVER_VENDOR_ID),
823 .idProduct = __constant_cpu_to_le16(DRIVER_PRODUCT_ID),
824 .bcdDevice = __constant_cpu_to_le16(0xffff),
825
826 .iManufacturer = STRING_MANUFACTURER,
827 .iProduct = STRING_PRODUCT,
828 .iSerialNumber = STRING_SERIAL,
829 .bNumConfigurations = 1,
830 };
831
832 static struct usb_config_descriptor
833 config_desc = {
834 .bLength = sizeof config_desc,
835 .bDescriptorType = USB_DT_CONFIG,
836
837 /* wTotalLength computed by usb_gadget_config_buf() */
838 .bNumInterfaces = 1,
839 .bConfigurationValue = CONFIG_VALUE,
840 .iConfiguration = STRING_CONFIG,
841 .bmAttributes = USB_CONFIG_ATT_ONE | USB_CONFIG_ATT_SELFPOWER,
842 .bMaxPower = 1, // self-powered
843 };
844
845 static struct usb_otg_descriptor
846 otg_desc = {
847 .bLength = sizeof(otg_desc),
848 .bDescriptorType = USB_DT_OTG,
849
850 .bmAttributes = USB_OTG_SRP,
851 };
852
853 /* There is only one interface. */
854
855 static struct usb_interface_descriptor
856 intf_desc = {
857 .bLength = sizeof intf_desc,
858 .bDescriptorType = USB_DT_INTERFACE,
859
860 .bNumEndpoints = 2, // Adjusted during fsg_bind()
861 .bInterfaceClass = USB_CLASS_MASS_STORAGE,
862 .bInterfaceSubClass = USB_SC_SCSI, // Adjusted during fsg_bind()
863 .bInterfaceProtocol = USB_PR_BULK, // Adjusted during fsg_bind()
864 .iInterface = STRING_INTERFACE,
865 };
866
867 /* Three full-speed endpoint descriptors: bulk-in, bulk-out,
868 * and interrupt-in. */
869
870 static struct usb_endpoint_descriptor
871 fs_bulk_in_desc = {
872 .bLength = USB_DT_ENDPOINT_SIZE,
873 .bDescriptorType = USB_DT_ENDPOINT,
874
875 .bEndpointAddress = USB_DIR_IN,
876 .bmAttributes = USB_ENDPOINT_XFER_BULK,
877 /* wMaxPacketSize set by autoconfiguration */
878 };
879
880 static struct usb_endpoint_descriptor
881 fs_bulk_out_desc = {
882 .bLength = USB_DT_ENDPOINT_SIZE,
883 .bDescriptorType = USB_DT_ENDPOINT,
884
885 .bEndpointAddress = USB_DIR_OUT,
886 .bmAttributes = USB_ENDPOINT_XFER_BULK,
887 /* wMaxPacketSize set by autoconfiguration */
888 };
889
890 static struct usb_endpoint_descriptor
891 fs_intr_in_desc = {
892 .bLength = USB_DT_ENDPOINT_SIZE,
893 .bDescriptorType = USB_DT_ENDPOINT,
894
895 .bEndpointAddress = USB_DIR_IN,
896 .bmAttributes = USB_ENDPOINT_XFER_INT,
897 .wMaxPacketSize = __constant_cpu_to_le16(2),
898 .bInterval = 32, // frames -> 32 ms
899 };
900
901 static const struct usb_descriptor_header *fs_function[] = {
902 (struct usb_descriptor_header *) &otg_desc,
903 (struct usb_descriptor_header *) &intf_desc,
904 (struct usb_descriptor_header *) &fs_bulk_in_desc,
905 (struct usb_descriptor_header *) &fs_bulk_out_desc,
906 (struct usb_descriptor_header *) &fs_intr_in_desc,
907 NULL,
908 };
909 #define FS_FUNCTION_PRE_EP_ENTRIES 2
910
911
912 /*
913 * USB 2.0 devices need to expose both high speed and full speed
914 * descriptors, unless they only run at full speed.
915 *
916 * That means alternate endpoint descriptors (bigger packets)
917 * and a "device qualifier" ... plus more construction options
918 * for the config descriptor.
919 */
920 static struct usb_qualifier_descriptor
921 dev_qualifier = {
922 .bLength = sizeof dev_qualifier,
923 .bDescriptorType = USB_DT_DEVICE_QUALIFIER,
924
925 .bcdUSB = __constant_cpu_to_le16(0x0200),
926 .bDeviceClass = USB_CLASS_PER_INTERFACE,
927
928 .bNumConfigurations = 1,
929 };
930
931 static struct usb_endpoint_descriptor
932 hs_bulk_in_desc = {
933 .bLength = USB_DT_ENDPOINT_SIZE,
934 .bDescriptorType = USB_DT_ENDPOINT,
935
936 /* bEndpointAddress copied from fs_bulk_in_desc during fsg_bind() */
937 .bmAttributes = USB_ENDPOINT_XFER_BULK,
938 .wMaxPacketSize = __constant_cpu_to_le16(512),
939 };
940
941 static struct usb_endpoint_descriptor
942 hs_bulk_out_desc = {
943 .bLength = USB_DT_ENDPOINT_SIZE,
944 .bDescriptorType = USB_DT_ENDPOINT,
945
946 /* bEndpointAddress copied from fs_bulk_out_desc during fsg_bind() */
947 .bmAttributes = USB_ENDPOINT_XFER_BULK,
948 .wMaxPacketSize = __constant_cpu_to_le16(512),
949 .bInterval = 1, // NAK every 1 uframe
950 };
951
952 static struct usb_endpoint_descriptor
953 hs_intr_in_desc = {
954 .bLength = USB_DT_ENDPOINT_SIZE,
955 .bDescriptorType = USB_DT_ENDPOINT,
956
957 /* bEndpointAddress copied from fs_intr_in_desc during fsg_bind() */
958 .bmAttributes = USB_ENDPOINT_XFER_INT,
959 .wMaxPacketSize = __constant_cpu_to_le16(2),
960 .bInterval = 9, // 2**(9-1) = 256 uframes -> 32 ms
961 };
962
963 static const struct usb_descriptor_header *hs_function[] = {
964 (struct usb_descriptor_header *) &otg_desc,
965 (struct usb_descriptor_header *) &intf_desc,
966 (struct usb_descriptor_header *) &hs_bulk_in_desc,
967 (struct usb_descriptor_header *) &hs_bulk_out_desc,
968 (struct usb_descriptor_header *) &hs_intr_in_desc,
969 NULL,
970 };
971 #define HS_FUNCTION_PRE_EP_ENTRIES 2
972
973 /* Maxpacket and other transfer characteristics vary by speed. */
974 static struct usb_endpoint_descriptor *
975 ep_desc(struct usb_gadget *g, struct usb_endpoint_descriptor *fs,
976 struct usb_endpoint_descriptor *hs)
977 {
978 if (gadget_is_dualspeed(g) && g->speed == USB_SPEED_HIGH)
979 return hs;
980 return fs;
981 }
982
983
984 /* The CBI specification limits the serial string to 12 uppercase hexadecimal
985 * characters. */
986 static char manufacturer[64];
987 static char serial[13];
988
989 /* Static strings, in UTF-8 (for simplicity we use only ASCII characters) */
990 static struct usb_string strings[] = {
991 {STRING_MANUFACTURER, manufacturer},
992 {STRING_PRODUCT, longname},
993 {STRING_SERIAL, serial},
994 {STRING_CONFIG, "Self-powered"},
995 {STRING_INTERFACE, "Mass Storage"},
996 {}
997 };
998
999 static struct usb_gadget_strings stringtab = {
1000 .language = 0x0409, // en-us
1001 .strings = strings,
1002 };
1003
1004
1005 /*
1006 * Config descriptors must agree with the code that sets configurations
1007 * and with code managing interfaces and their altsettings. They must
1008 * also handle different speeds and other-speed requests.
1009 */
1010 static int populate_config_buf(struct usb_gadget *gadget,
1011 u8 *buf, u8 type, unsigned index)
1012 {
1013 enum usb_device_speed speed = gadget->speed;
1014 int len;
1015 const struct usb_descriptor_header **function;
1016
1017 if (index > 0)
1018 return -EINVAL;
1019
1020 if (gadget_is_dualspeed(gadget) && type == USB_DT_OTHER_SPEED_CONFIG)
1021 speed = (USB_SPEED_FULL + USB_SPEED_HIGH) - speed;
1022 if (gadget_is_dualspeed(gadget) && speed == USB_SPEED_HIGH)
1023 function = hs_function;
1024 else
1025 function = fs_function;
1026
1027 /* for now, don't advertise srp-only devices */
1028 if (!gadget_is_otg(gadget))
1029 function++;
1030
1031 len = usb_gadget_config_buf(&config_desc, buf, EP0_BUFSIZE, function);
1032 ((struct usb_config_descriptor *) buf)->bDescriptorType = type;
1033 return len;
1034 }
1035
1036
1037 /*-------------------------------------------------------------------------*/
1038
1039 /* These routines may be called in process context or in_irq */
1040
1041 /* Caller must hold fsg->lock */
1042 static void wakeup_thread(struct fsg_dev *fsg)
1043 {
1044 /* Tell the main thread that something has happened */
1045 fsg->thread_wakeup_needed = 1;
1046 if (fsg->thread_task)
1047 wake_up_process(fsg->thread_task);
1048 }
1049
1050
1051 static void raise_exception(struct fsg_dev *fsg, enum fsg_state new_state)
1052 {
1053 unsigned long flags;
1054
1055 /* Do nothing if a higher-priority exception is already in progress.
1056 * If a lower-or-equal priority exception is in progress, preempt it
1057 * and notify the main thread by sending it a signal. */
1058 spin_lock_irqsave(&fsg->lock, flags);
1059 if (fsg->state <= new_state) {
1060 fsg->exception_req_tag = fsg->ep0_req_tag;
1061 fsg->state = new_state;
1062 if (fsg->thread_task)
1063 send_sig_info(SIGUSR1, SEND_SIG_FORCED,
1064 fsg->thread_task);
1065 }
1066 spin_unlock_irqrestore(&fsg->lock, flags);
1067 }
1068
1069
1070 /*-------------------------------------------------------------------------*/
1071
1072 /* The disconnect callback and ep0 routines. These always run in_irq,
1073 * except that ep0_queue() is called in the main thread to acknowledge
1074 * completion of various requests: set config, set interface, and
1075 * Bulk-only device reset. */
1076
1077 static void fsg_disconnect(struct usb_gadget *gadget)
1078 {
1079 struct fsg_dev *fsg = get_gadget_data(gadget);
1080
1081 DBG(fsg, "disconnect or port reset\n");
1082 raise_exception(fsg, FSG_STATE_DISCONNECT);
1083 }
1084
1085
1086 static int ep0_queue(struct fsg_dev *fsg)
1087 {
1088 int rc;
1089
1090 rc = usb_ep_queue(fsg->ep0, fsg->ep0req, GFP_ATOMIC);
1091 if (rc != 0 && rc != -ESHUTDOWN) {
1092
1093 /* We can't do much more than wait for a reset */
1094 WARN(fsg, "error in submission: %s --> %d\n",
1095 fsg->ep0->name, rc);
1096 }
1097 return rc;
1098 }
1099
1100 static void ep0_complete(struct usb_ep *ep, struct usb_request *req)
1101 {
1102 struct fsg_dev *fsg = ep->driver_data;
1103
1104 if (req->actual > 0)
1105 dump_msg(fsg, fsg->ep0req_name, req->buf, req->actual);
1106 if (req->status || req->actual != req->length)
1107 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1108 req->status, req->actual, req->length);
1109 if (req->status == -ECONNRESET) // Request was cancelled
1110 usb_ep_fifo_flush(ep);
1111
1112 if (req->status == 0 && req->context)
1113 ((fsg_routine_t) (req->context))(fsg);
1114 }
1115
1116
1117 /*-------------------------------------------------------------------------*/
1118
1119 /* Bulk and interrupt endpoint completion handlers.
1120 * These always run in_irq. */
1121
1122 static void bulk_in_complete(struct usb_ep *ep, struct usb_request *req)
1123 {
1124 struct fsg_dev *fsg = ep->driver_data;
1125 struct fsg_buffhd *bh = req->context;
1126
1127 if (req->status || req->actual != req->length)
1128 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1129 req->status, req->actual, req->length);
1130 if (req->status == -ECONNRESET) // Request was cancelled
1131 usb_ep_fifo_flush(ep);
1132
1133 /* Hold the lock while we update the request and buffer states */
1134 smp_wmb();
1135 spin_lock(&fsg->lock);
1136 bh->inreq_busy = 0;
1137 bh->state = BUF_STATE_EMPTY;
1138 wakeup_thread(fsg);
1139 spin_unlock(&fsg->lock);
1140 }
1141
1142 static void bulk_out_complete(struct usb_ep *ep, struct usb_request *req)
1143 {
1144 struct fsg_dev *fsg = ep->driver_data;
1145 struct fsg_buffhd *bh = req->context;
1146
1147 dump_msg(fsg, "bulk-out", req->buf, req->actual);
1148 if (req->status || req->actual != bh->bulk_out_intended_length)
1149 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1150 req->status, req->actual,
1151 bh->bulk_out_intended_length);
1152 if (req->status == -ECONNRESET) // Request was cancelled
1153 usb_ep_fifo_flush(ep);
1154
1155 /* Hold the lock while we update the request and buffer states */
1156 smp_wmb();
1157 spin_lock(&fsg->lock);
1158 bh->outreq_busy = 0;
1159 bh->state = BUF_STATE_FULL;
1160 wakeup_thread(fsg);
1161 spin_unlock(&fsg->lock);
1162 }
1163
1164
1165 #ifdef CONFIG_USB_FILE_STORAGE_TEST
1166 static void intr_in_complete(struct usb_ep *ep, struct usb_request *req)
1167 {
1168 struct fsg_dev *fsg = ep->driver_data;
1169 struct fsg_buffhd *bh = req->context;
1170
1171 if (req->status || req->actual != req->length)
1172 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1173 req->status, req->actual, req->length);
1174 if (req->status == -ECONNRESET) // Request was cancelled
1175 usb_ep_fifo_flush(ep);
1176
1177 /* Hold the lock while we update the request and buffer states */
1178 smp_wmb();
1179 spin_lock(&fsg->lock);
1180 fsg->intreq_busy = 0;
1181 bh->state = BUF_STATE_EMPTY;
1182 wakeup_thread(fsg);
1183 spin_unlock(&fsg->lock);
1184 }
1185
1186 #else
1187 static void intr_in_complete(struct usb_ep *ep, struct usb_request *req)
1188 {}
1189 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
1190
1191
1192 /*-------------------------------------------------------------------------*/
1193
1194 /* Ep0 class-specific handlers. These always run in_irq. */
1195
1196 #ifdef CONFIG_USB_FILE_STORAGE_TEST
1197 static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
1198 {
1199 struct usb_request *req = fsg->ep0req;
1200 static u8 cbi_reset_cmnd[6] = {
1201 SC_SEND_DIAGNOSTIC, 4, 0xff, 0xff, 0xff, 0xff};
1202
1203 /* Error in command transfer? */
1204 if (req->status || req->length != req->actual ||
1205 req->actual < 6 || req->actual > MAX_COMMAND_SIZE) {
1206
1207 /* Not all controllers allow a protocol stall after
1208 * receiving control-out data, but we'll try anyway. */
1209 fsg_set_halt(fsg, fsg->ep0);
1210 return; // Wait for reset
1211 }
1212
1213 /* Is it the special reset command? */
1214 if (req->actual >= sizeof cbi_reset_cmnd &&
1215 memcmp(req->buf, cbi_reset_cmnd,
1216 sizeof cbi_reset_cmnd) == 0) {
1217
1218 /* Raise an exception to stop the current operation
1219 * and reinitialize our state. */
1220 DBG(fsg, "cbi reset request\n");
1221 raise_exception(fsg, FSG_STATE_RESET);
1222 return;
1223 }
1224
1225 VDBG(fsg, "CB[I] accept device-specific command\n");
1226 spin_lock(&fsg->lock);
1227
1228 /* Save the command for later */
1229 if (fsg->cbbuf_cmnd_size)
1230 WARN(fsg, "CB[I] overwriting previous command\n");
1231 fsg->cbbuf_cmnd_size = req->actual;
1232 memcpy(fsg->cbbuf_cmnd, req->buf, fsg->cbbuf_cmnd_size);
1233
1234 wakeup_thread(fsg);
1235 spin_unlock(&fsg->lock);
1236 }
1237
1238 #else
1239 static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
1240 {}
1241 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
1242
1243
1244 static int class_setup_req(struct fsg_dev *fsg,
1245 const struct usb_ctrlrequest *ctrl)
1246 {
1247 struct usb_request *req = fsg->ep0req;
1248 int value = -EOPNOTSUPP;
1249 u16 w_index = le16_to_cpu(ctrl->wIndex);
1250 u16 w_value = le16_to_cpu(ctrl->wValue);
1251 u16 w_length = le16_to_cpu(ctrl->wLength);
1252
1253 if (!fsg->config)
1254 return value;
1255
1256 /* Handle Bulk-only class-specific requests */
1257 if (transport_is_bbb()) {
1258 switch (ctrl->bRequest) {
1259
1260 case USB_BULK_RESET_REQUEST:
1261 if (ctrl->bRequestType != (USB_DIR_OUT |
1262 USB_TYPE_CLASS | USB_RECIP_INTERFACE))
1263 break;
1264 if (w_index != 0 || w_value != 0) {
1265 value = -EDOM;
1266 break;
1267 }
1268
1269 /* Raise an exception to stop the current operation
1270 * and reinitialize our state. */
1271 DBG(fsg, "bulk reset request\n");
1272 raise_exception(fsg, FSG_STATE_RESET);
1273 value = DELAYED_STATUS;
1274 break;
1275
1276 case USB_BULK_GET_MAX_LUN_REQUEST:
1277 if (ctrl->bRequestType != (USB_DIR_IN |
1278 USB_TYPE_CLASS | USB_RECIP_INTERFACE))
1279 break;
1280 if (w_index != 0 || w_value != 0) {
1281 value = -EDOM;
1282 break;
1283 }
1284 VDBG(fsg, "get max LUN\n");
1285 *(u8 *) req->buf = fsg->nluns - 1;
1286 value = 1;
1287 break;
1288 }
1289 }
1290
1291 /* Handle CBI class-specific requests */
1292 else {
1293 switch (ctrl->bRequest) {
1294
1295 case USB_CBI_ADSC_REQUEST:
1296 if (ctrl->bRequestType != (USB_DIR_OUT |
1297 USB_TYPE_CLASS | USB_RECIP_INTERFACE))
1298 break;
1299 if (w_index != 0 || w_value != 0) {
1300 value = -EDOM;
1301 break;
1302 }
1303 if (w_length > MAX_COMMAND_SIZE) {
1304 value = -EOVERFLOW;
1305 break;
1306 }
1307 value = w_length;
1308 fsg->ep0req->context = received_cbi_adsc;
1309 break;
1310 }
1311 }
1312
1313 if (value == -EOPNOTSUPP)
1314 VDBG(fsg,
1315 "unknown class-specific control req "
1316 "%02x.%02x v%04x i%04x l%u\n",
1317 ctrl->bRequestType, ctrl->bRequest,
1318 le16_to_cpu(ctrl->wValue), w_index, w_length);
1319 return value;
1320 }
1321
1322
1323 /*-------------------------------------------------------------------------*/
1324
1325 /* Ep0 standard request handlers. These always run in_irq. */
1326
1327 static int standard_setup_req(struct fsg_dev *fsg,
1328 const struct usb_ctrlrequest *ctrl)
1329 {
1330 struct usb_request *req = fsg->ep0req;
1331 int value = -EOPNOTSUPP;
1332 u16 w_index = le16_to_cpu(ctrl->wIndex);
1333 u16 w_value = le16_to_cpu(ctrl->wValue);
1334
1335 /* Usually this just stores reply data in the pre-allocated ep0 buffer,
1336 * but config change events will also reconfigure hardware. */
1337 switch (ctrl->bRequest) {
1338
1339 case USB_REQ_GET_DESCRIPTOR:
1340 if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
1341 USB_RECIP_DEVICE))
1342 break;
1343 switch (w_value >> 8) {
1344
1345 case USB_DT_DEVICE:
1346 VDBG(fsg, "get device descriptor\n");
1347 value = sizeof device_desc;
1348 memcpy(req->buf, &device_desc, value);
1349 break;
1350 case USB_DT_DEVICE_QUALIFIER:
1351 VDBG(fsg, "get device qualifier\n");
1352 if (!gadget_is_dualspeed(fsg->gadget))
1353 break;
1354 value = sizeof dev_qualifier;
1355 memcpy(req->buf, &dev_qualifier, value);
1356 break;
1357
1358 case USB_DT_OTHER_SPEED_CONFIG:
1359 VDBG(fsg, "get other-speed config descriptor\n");
1360 if (!gadget_is_dualspeed(fsg->gadget))
1361 break;
1362 goto get_config;
1363 case USB_DT_CONFIG:
1364 VDBG(fsg, "get configuration descriptor\n");
1365 get_config:
1366 value = populate_config_buf(fsg->gadget,
1367 req->buf,
1368 w_value >> 8,
1369 w_value & 0xff);
1370 break;
1371
1372 case USB_DT_STRING:
1373 VDBG(fsg, "get string descriptor\n");
1374
1375 /* wIndex == language code */
1376 value = usb_gadget_get_string(&stringtab,
1377 w_value & 0xff, req->buf);
1378 break;
1379 }
1380 break;
1381
1382 /* One config, two speeds */
1383 case USB_REQ_SET_CONFIGURATION:
1384 if (ctrl->bRequestType != (USB_DIR_OUT | USB_TYPE_STANDARD |
1385 USB_RECIP_DEVICE))
1386 break;
1387 VDBG(fsg, "set configuration\n");
1388 if (w_value == CONFIG_VALUE || w_value == 0) {
1389 fsg->new_config = w_value;
1390
1391 /* Raise an exception to wipe out previous transaction
1392 * state (queued bufs, etc) and set the new config. */
1393 raise_exception(fsg, FSG_STATE_CONFIG_CHANGE);
1394 value = DELAYED_STATUS;
1395 }
1396 break;
1397 case USB_REQ_GET_CONFIGURATION:
1398 if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
1399 USB_RECIP_DEVICE))
1400 break;
1401 VDBG(fsg, "get configuration\n");
1402 *(u8 *) req->buf = fsg->config;
1403 value = 1;
1404 break;
1405
1406 case USB_REQ_SET_INTERFACE:
1407 if (ctrl->bRequestType != (USB_DIR_OUT| USB_TYPE_STANDARD |
1408 USB_RECIP_INTERFACE))
1409 break;
1410 if (fsg->config && w_index == 0) {
1411
1412 /* Raise an exception to wipe out previous transaction
1413 * state (queued bufs, etc) and install the new
1414 * interface altsetting. */
1415 raise_exception(fsg, FSG_STATE_INTERFACE_CHANGE);
1416 value = DELAYED_STATUS;
1417 }
1418 break;
1419 case USB_REQ_GET_INTERFACE:
1420 if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
1421 USB_RECIP_INTERFACE))
1422 break;
1423 if (!fsg->config)
1424 break;
1425 if (w_index != 0) {
1426 value = -EDOM;
1427 break;
1428 }
1429 VDBG(fsg, "get interface\n");
1430 *(u8 *) req->buf = 0;
1431 value = 1;
1432 break;
1433
1434 default:
1435 VDBG(fsg,
1436 "unknown control req %02x.%02x v%04x i%04x l%u\n",
1437 ctrl->bRequestType, ctrl->bRequest,
1438 w_value, w_index, le16_to_cpu(ctrl->wLength));
1439 }
1440
1441 return value;
1442 }
1443
1444
1445 static int fsg_setup(struct usb_gadget *gadget,
1446 const struct usb_ctrlrequest *ctrl)
1447 {
1448 struct fsg_dev *fsg = get_gadget_data(gadget);
1449 int rc;
1450 int w_length = le16_to_cpu(ctrl->wLength);
1451
1452 ++fsg->ep0_req_tag; // Record arrival of a new request
1453 fsg->ep0req->context = NULL;
1454 fsg->ep0req->length = 0;
1455 dump_msg(fsg, "ep0-setup", (u8 *) ctrl, sizeof(*ctrl));
1456
1457 if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_CLASS)
1458 rc = class_setup_req(fsg, ctrl);
1459 else
1460 rc = standard_setup_req(fsg, ctrl);
1461
1462 /* Respond with data/status or defer until later? */
1463 if (rc >= 0 && rc != DELAYED_STATUS) {
1464 rc = min(rc, w_length);
1465 fsg->ep0req->length = rc;
1466 fsg->ep0req->zero = rc < w_length;
1467 fsg->ep0req_name = (ctrl->bRequestType & USB_DIR_IN ?
1468 "ep0-in" : "ep0-out");
1469 rc = ep0_queue(fsg);
1470 }
1471
1472 /* Device either stalls (rc < 0) or reports success */
1473 return rc;
1474 }
1475
1476
1477 /*-------------------------------------------------------------------------*/
1478
1479 /* All the following routines run in process context */
1480
1481
1482 /* Use this for bulk or interrupt transfers, not ep0 */
1483 static void start_transfer(struct fsg_dev *fsg, struct usb_ep *ep,
1484 struct usb_request *req, int *pbusy,
1485 enum fsg_buffer_state *state)
1486 {
1487 int rc;
1488
1489 if (ep == fsg->bulk_in)
1490 dump_msg(fsg, "bulk-in", req->buf, req->length);
1491 else if (ep == fsg->intr_in)
1492 dump_msg(fsg, "intr-in", req->buf, req->length);
1493
1494 spin_lock_irq(&fsg->lock);
1495 *pbusy = 1;
1496 *state = BUF_STATE_BUSY;
1497 spin_unlock_irq(&fsg->lock);
1498 rc = usb_ep_queue(ep, req, GFP_KERNEL);
1499 if (rc != 0) {
1500 *pbusy = 0;
1501 *state = BUF_STATE_EMPTY;
1502
1503 /* We can't do much more than wait for a reset */
1504
1505 /* Note: currently the net2280 driver fails zero-length
1506 * submissions if DMA is enabled. */
1507 if (rc != -ESHUTDOWN && !(rc == -EOPNOTSUPP &&
1508 req->length == 0))
1509 WARN(fsg, "error in submission: %s --> %d\n",
1510 ep->name, rc);
1511 }
1512 }
1513
1514
1515 static int sleep_thread(struct fsg_dev *fsg)
1516 {
1517 int rc = 0;
1518
1519 /* Wait until a signal arrives or we are woken up */
1520 for (;;) {
1521 try_to_freeze();
1522 set_current_state(TASK_INTERRUPTIBLE);
1523 if (signal_pending(current)) {
1524 rc = -EINTR;
1525 break;
1526 }
1527 if (fsg->thread_wakeup_needed)
1528 break;
1529 schedule();
1530 }
1531 __set_current_state(TASK_RUNNING);
1532 fsg->thread_wakeup_needed = 0;
1533 return rc;
1534 }
1535
1536
1537 /*-------------------------------------------------------------------------*/
1538
1539 static int do_read(struct fsg_dev *fsg)
1540 {
1541 struct lun *curlun = fsg->curlun;
1542 u32 lba;
1543 struct fsg_buffhd *bh;
1544 int rc;
1545 u32 amount_left;
1546 loff_t file_offset, file_offset_tmp;
1547 unsigned int amount;
1548 unsigned int partial_page;
1549 ssize_t nread;
1550
1551 /* Get the starting Logical Block Address and check that it's
1552 * not too big */
1553 if (fsg->cmnd[0] == SC_READ_6)
1554 lba = (fsg->cmnd[1] << 16) | get_be16(&fsg->cmnd[2]);
1555 else {
1556 lba = get_be32(&fsg->cmnd[2]);
1557
1558 /* We allow DPO (Disable Page Out = don't save data in the
1559 * cache) and FUA (Force Unit Access = don't read from the
1560 * cache), but we don't implement them. */
1561 if ((fsg->cmnd[1] & ~0x18) != 0) {
1562 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
1563 return -EINVAL;
1564 }
1565 }
1566 if (lba >= curlun->num_sectors) {
1567 curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1568 return -EINVAL;
1569 }
1570 file_offset = ((loff_t) lba) << 9;
1571
1572 /* Carry out the file reads */
1573 amount_left = fsg->data_size_from_cmnd;
1574 if (unlikely(amount_left == 0))
1575 return -EIO; // No default reply
1576
1577 for (;;) {
1578
1579 /* Figure out how much we need to read:
1580 * Try to read the remaining amount.
1581 * But don't read more than the buffer size.
1582 * And don't try to read past the end of the file.
1583 * Finally, if we're not at a page boundary, don't read past
1584 * the next page.
1585 * If this means reading 0 then we were asked to read past
1586 * the end of file. */
1587 amount = min((unsigned int) amount_left, mod_data.buflen);
1588 amount = min((loff_t) amount,
1589 curlun->file_length - file_offset);
1590 partial_page = file_offset & (PAGE_CACHE_SIZE - 1);
1591 if (partial_page > 0)
1592 amount = min(amount, (unsigned int) PAGE_CACHE_SIZE -
1593 partial_page);
1594
1595 /* Wait for the next buffer to become available */
1596 bh = fsg->next_buffhd_to_fill;
1597 while (bh->state != BUF_STATE_EMPTY) {
1598 rc = sleep_thread(fsg);
1599 if (rc)
1600 return rc;
1601 }
1602
1603 /* If we were asked to read past the end of file,
1604 * end with an empty buffer. */
1605 if (amount == 0) {
1606 curlun->sense_data =
1607 SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1608 curlun->sense_data_info = file_offset >> 9;
1609 curlun->info_valid = 1;
1610 bh->inreq->length = 0;
1611 bh->state = BUF_STATE_FULL;
1612 break;
1613 }
1614
1615 /* Perform the read */
1616 file_offset_tmp = file_offset;
1617 nread = vfs_read(curlun->filp,
1618 (char __user *) bh->buf,
1619 amount, &file_offset_tmp);
1620 VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
1621 (unsigned long long) file_offset,
1622 (int) nread);
1623 if (signal_pending(current))
1624 return -EINTR;
1625
1626 if (nread < 0) {
1627 LDBG(curlun, "error in file read: %d\n",
1628 (int) nread);
1629 nread = 0;
1630 } else if (nread < amount) {
1631 LDBG(curlun, "partial file read: %d/%u\n",
1632 (int) nread, amount);
1633 nread -= (nread & 511); // Round down to a block
1634 }
1635 file_offset += nread;
1636 amount_left -= nread;
1637 fsg->residue -= nread;
1638 bh->inreq->length = nread;
1639 bh->state = BUF_STATE_FULL;
1640
1641 /* If an error occurred, report it and its position */
1642 if (nread < amount) {
1643 curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
1644 curlun->sense_data_info = file_offset >> 9;
1645 curlun->info_valid = 1;
1646 break;
1647 }
1648
1649 if (amount_left == 0)
1650 break; // No more left to read
1651
1652 /* Send this buffer and go read some more */
1653 bh->inreq->zero = 0;
1654 start_transfer(fsg, fsg->bulk_in, bh->inreq,
1655 &bh->inreq_busy, &bh->state);
1656 fsg->next_buffhd_to_fill = bh->next;
1657 }
1658
1659 return -EIO; // No default reply
1660 }
1661
1662
1663 /*-------------------------------------------------------------------------*/
1664
1665 static int do_write(struct fsg_dev *fsg)
1666 {
1667 struct lun *curlun = fsg->curlun;
1668 u32 lba;
1669 struct fsg_buffhd *bh;
1670 int get_some_more;
1671 u32 amount_left_to_req, amount_left_to_write;
1672 loff_t usb_offset, file_offset, file_offset_tmp;
1673 unsigned int amount;
1674 unsigned int partial_page;
1675 ssize_t nwritten;
1676 int rc;
1677
1678 if (curlun->ro) {
1679 curlun->sense_data = SS_WRITE_PROTECTED;
1680 return -EINVAL;
1681 }
1682 curlun->filp->f_flags &= ~O_SYNC; // Default is not to wait
1683
1684 /* Get the starting Logical Block Address and check that it's
1685 * not too big */
1686 if (fsg->cmnd[0] == SC_WRITE_6)
1687 lba = (fsg->cmnd[1] << 16) | get_be16(&fsg->cmnd[2]);
1688 else {
1689 lba = get_be32(&fsg->cmnd[2]);
1690
1691 /* We allow DPO (Disable Page Out = don't save data in the
1692 * cache) and FUA (Force Unit Access = write directly to the
1693 * medium). We don't implement DPO; we implement FUA by
1694 * performing synchronous output. */
1695 if ((fsg->cmnd[1] & ~0x18) != 0) {
1696 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
1697 return -EINVAL;
1698 }
1699 if (fsg->cmnd[1] & 0x08) // FUA
1700 curlun->filp->f_flags |= O_SYNC;
1701 }
1702 if (lba >= curlun->num_sectors) {
1703 curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1704 return -EINVAL;
1705 }
1706
1707 /* Carry out the file writes */
1708 get_some_more = 1;
1709 file_offset = usb_offset = ((loff_t) lba) << 9;
1710 amount_left_to_req = amount_left_to_write = fsg->data_size_from_cmnd;
1711
1712 while (amount_left_to_write > 0) {
1713
1714 /* Queue a request for more data from the host */
1715 bh = fsg->next_buffhd_to_fill;
1716 if (bh->state == BUF_STATE_EMPTY && get_some_more) {
1717
1718 /* Figure out how much we want to get:
1719 * Try to get the remaining amount.
1720 * But don't get more than the buffer size.
1721 * And don't try to go past the end of the file.
1722 * If we're not at a page boundary,
1723 * don't go past the next page.
1724 * If this means getting 0, then we were asked
1725 * to write past the end of file.
1726 * Finally, round down to a block boundary. */
1727 amount = min(amount_left_to_req, mod_data.buflen);
1728 amount = min((loff_t) amount, curlun->file_length -
1729 usb_offset);
1730 partial_page = usb_offset & (PAGE_CACHE_SIZE - 1);
1731 if (partial_page > 0)
1732 amount = min(amount,
1733 (unsigned int) PAGE_CACHE_SIZE - partial_page);
1734
1735 if (amount == 0) {
1736 get_some_more = 0;
1737 curlun->sense_data =
1738 SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1739 curlun->sense_data_info = usb_offset >> 9;
1740 curlun->info_valid = 1;
1741 continue;
1742 }
1743 amount -= (amount & 511);
1744 if (amount == 0) {
1745
1746 /* Why were we were asked to transfer a
1747 * partial block? */
1748 get_some_more = 0;
1749 continue;
1750 }
1751
1752 /* Get the next buffer */
1753 usb_offset += amount;
1754 fsg->usb_amount_left -= amount;
1755 amount_left_to_req -= amount;
1756 if (amount_left_to_req == 0)
1757 get_some_more = 0;
1758
1759 /* amount is always divisible by 512, hence by
1760 * the bulk-out maxpacket size */
1761 bh->outreq->length = bh->bulk_out_intended_length =
1762 amount;
1763 bh->outreq->short_not_ok = 1;
1764 start_transfer(fsg, fsg->bulk_out, bh->outreq,
1765 &bh->outreq_busy, &bh->state);
1766 fsg->next_buffhd_to_fill = bh->next;
1767 continue;
1768 }
1769
1770 /* Write the received data to the backing file */
1771 bh = fsg->next_buffhd_to_drain;
1772 if (bh->state == BUF_STATE_EMPTY && !get_some_more)
1773 break; // We stopped early
1774 if (bh->state == BUF_STATE_FULL) {
1775 smp_rmb();
1776 fsg->next_buffhd_to_drain = bh->next;
1777 bh->state = BUF_STATE_EMPTY;
1778
1779 /* Did something go wrong with the transfer? */
1780 if (bh->outreq->status != 0) {
1781 curlun->sense_data = SS_COMMUNICATION_FAILURE;
1782 curlun->sense_data_info = file_offset >> 9;
1783 curlun->info_valid = 1;
1784 break;
1785 }
1786
1787 amount = bh->outreq->actual;
1788 if (curlun->file_length - file_offset < amount) {
1789 LERROR(curlun,
1790 "write %u @ %llu beyond end %llu\n",
1791 amount, (unsigned long long) file_offset,
1792 (unsigned long long) curlun->file_length);
1793 amount = curlun->file_length - file_offset;
1794 }
1795
1796 /* Perform the write */
1797 file_offset_tmp = file_offset;
1798 nwritten = vfs_write(curlun->filp,
1799 (char __user *) bh->buf,
1800 amount, &file_offset_tmp);
1801 VLDBG(curlun, "file write %u @ %llu -> %d\n", amount,
1802 (unsigned long long) file_offset,
1803 (int) nwritten);
1804 if (signal_pending(current))
1805 return -EINTR; // Interrupted!
1806
1807 if (nwritten < 0) {
1808 LDBG(curlun, "error in file write: %d\n",
1809 (int) nwritten);
1810 nwritten = 0;
1811 } else if (nwritten < amount) {
1812 LDBG(curlun, "partial file write: %d/%u\n",
1813 (int) nwritten, amount);
1814 nwritten -= (nwritten & 511);
1815 // Round down to a block
1816 }
1817 file_offset += nwritten;
1818 amount_left_to_write -= nwritten;
1819 fsg->residue -= nwritten;
1820
1821 /* If an error occurred, report it and its position */
1822 if (nwritten < amount) {
1823 curlun->sense_data = SS_WRITE_ERROR;
1824 curlun->sense_data_info = file_offset >> 9;
1825 curlun->info_valid = 1;
1826 break;
1827 }
1828
1829 /* Did the host decide to stop early? */
1830 if (bh->outreq->actual != bh->outreq->length) {
1831 fsg->short_packet_received = 1;
1832 break;
1833 }
1834 continue;
1835 }
1836
1837 /* Wait for something to happen */
1838 rc = sleep_thread(fsg);
1839 if (rc)
1840 return rc;
1841 }
1842
1843 return -EIO; // No default reply
1844 }
1845
1846
1847 /*-------------------------------------------------------------------------*/
1848
1849 /* Sync the file data, don't bother with the metadata.
1850 * This code was copied from fs/buffer.c:sys_fdatasync(). */
1851 static int fsync_sub(struct lun *curlun)
1852 {
1853 struct file *filp = curlun->filp;
1854 struct inode *inode;
1855 int rc, err;
1856
1857 if (curlun->ro || !filp)
1858 return 0;
1859 if (!filp->f_op->fsync)
1860 return -EINVAL;
1861
1862 inode = filp->f_path.dentry->d_inode;
1863 mutex_lock(&inode->i_mutex);
1864 rc = filemap_fdatawrite(inode->i_mapping);
1865 err = filp->f_op->fsync(filp, filp->f_path.dentry, 1);
1866 if (!rc)
1867 rc = err;
1868 err = filemap_fdatawait(inode->i_mapping);
1869 if (!rc)
1870 rc = err;
1871 mutex_unlock(&inode->i_mutex);
1872 VLDBG(curlun, "fdatasync -> %d\n", rc);
1873 return rc;
1874 }
1875
1876 static void fsync_all(struct fsg_dev *fsg)
1877 {
1878 int i;
1879
1880 for (i = 0; i < fsg->nluns; ++i)
1881 fsync_sub(&fsg->luns[i]);
1882 }
1883
1884 static int do_synchronize_cache(struct fsg_dev *fsg)
1885 {
1886 struct lun *curlun = fsg->curlun;
1887 int rc;
1888
1889 /* We ignore the requested LBA and write out all file's
1890 * dirty data buffers. */
1891 rc = fsync_sub(curlun);
1892 if (rc)
1893 curlun->sense_data = SS_WRITE_ERROR;
1894 return 0;
1895 }
1896
1897
1898 /*-------------------------------------------------------------------------*/
1899
1900 static void invalidate_sub(struct lun *curlun)
1901 {
1902 struct file *filp = curlun->filp;
1903 struct inode *inode = filp->f_path.dentry->d_inode;
1904 unsigned long rc;
1905
1906 rc = invalidate_mapping_pages(inode->i_mapping, 0, -1);
1907 VLDBG(curlun, "invalidate_inode_pages -> %ld\n", rc);
1908 }
1909
1910 static int do_verify(struct fsg_dev *fsg)
1911 {
1912 struct lun *curlun = fsg->curlun;
1913 u32 lba;
1914 u32 verification_length;
1915 struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
1916 loff_t file_offset, file_offset_tmp;
1917 u32 amount_left;
1918 unsigned int amount;
1919 ssize_t nread;
1920
1921 /* Get the starting Logical Block Address and check that it's
1922 * not too big */
1923 lba = get_be32(&fsg->cmnd[2]);
1924 if (lba >= curlun->num_sectors) {
1925 curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1926 return -EINVAL;
1927 }
1928
1929 /* We allow DPO (Disable Page Out = don't save data in the
1930 * cache) but we don't implement it. */
1931 if ((fsg->cmnd[1] & ~0x10) != 0) {
1932 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
1933 return -EINVAL;
1934 }
1935
1936 verification_length = get_be16(&fsg->cmnd[7]);
1937 if (unlikely(verification_length == 0))
1938 return -EIO; // No default reply
1939
1940 /* Prepare to carry out the file verify */
1941 amount_left = verification_length << 9;
1942 file_offset = ((loff_t) lba) << 9;
1943
1944 /* Write out all the dirty buffers before invalidating them */
1945 fsync_sub(curlun);
1946 if (signal_pending(current))
1947 return -EINTR;
1948
1949 invalidate_sub(curlun);
1950 if (signal_pending(current))
1951 return -EINTR;
1952
1953 /* Just try to read the requested blocks */
1954 while (amount_left > 0) {
1955
1956 /* Figure out how much we need to read:
1957 * Try to read the remaining amount, but not more than
1958 * the buffer size.
1959 * And don't try to read past the end of the file.
1960 * If this means reading 0 then we were asked to read
1961 * past the end of file. */
1962 amount = min((unsigned int) amount_left, mod_data.buflen);
1963 amount = min((loff_t) amount,
1964 curlun->file_length - file_offset);
1965 if (amount == 0) {
1966 curlun->sense_data =
1967 SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1968 curlun->sense_data_info = file_offset >> 9;
1969 curlun->info_valid = 1;
1970 break;
1971 }
1972
1973 /* Perform the read */
1974 file_offset_tmp = file_offset;
1975 nread = vfs_read(curlun->filp,
1976 (char __user *) bh->buf,
1977 amount, &file_offset_tmp);
1978 VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
1979 (unsigned long long) file_offset,
1980 (int) nread);
1981 if (signal_pending(current))
1982 return -EINTR;
1983
1984 if (nread < 0) {
1985 LDBG(curlun, "error in file verify: %d\n",
1986 (int) nread);
1987 nread = 0;
1988 } else if (nread < amount) {
1989 LDBG(curlun, "partial file verify: %d/%u\n",
1990 (int) nread, amount);
1991 nread -= (nread & 511); // Round down to a sector
1992 }
1993 if (nread == 0) {
1994 curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
1995 curlun->sense_data_info = file_offset >> 9;
1996 curlun->info_valid = 1;
1997 break;
1998 }
1999 file_offset += nread;
2000 amount_left -= nread;
2001 }
2002 return 0;
2003 }
2004
2005
2006 /*-------------------------------------------------------------------------*/
2007
2008 static int do_inquiry(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2009 {
2010 u8 *buf = (u8 *) bh->buf;
2011
2012 static char vendor_id[] = "Linux ";
2013 static char product_id[] = "File-Stor Gadget";
2014
2015 if (!fsg->curlun) { // Unsupported LUNs are okay
2016 fsg->bad_lun_okay = 1;
2017 memset(buf, 0, 36);
2018 buf[0] = 0x7f; // Unsupported, no device-type
2019 return 36;
2020 }
2021
2022 memset(buf, 0, 8); // Non-removable, direct-access device
2023 if (mod_data.removable)
2024 buf[1] = 0x80;
2025 buf[2] = 2; // ANSI SCSI level 2
2026 buf[3] = 2; // SCSI-2 INQUIRY data format
2027 buf[4] = 31; // Additional length
2028 // No special options
2029 sprintf(buf + 8, "%-8s%-16s%04x", vendor_id, product_id,
2030 mod_data.release);
2031 return 36;
2032 }
2033
2034
2035 static int do_request_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2036 {
2037 struct lun *curlun = fsg->curlun;
2038 u8 *buf = (u8 *) bh->buf;
2039 u32 sd, sdinfo;
2040 int valid;
2041
2042 /*
2043 * From the SCSI-2 spec., section 7.9 (Unit attention condition):
2044 *
2045 * If a REQUEST SENSE command is received from an initiator
2046 * with a pending unit attention condition (before the target
2047 * generates the contingent allegiance condition), then the
2048 * target shall either:
2049 * a) report any pending sense data and preserve the unit
2050 * attention condition on the logical unit, or,
2051 * b) report the unit attention condition, may discard any
2052 * pending sense data, and clear the unit attention
2053 * condition on the logical unit for that initiator.
2054 *
2055 * FSG normally uses option a); enable this code to use option b).
2056 */
2057 #if 0
2058 if (curlun && curlun->unit_attention_data != SS_NO_SENSE) {
2059 curlun->sense_data = curlun->unit_attention_data;
2060 curlun->unit_attention_data = SS_NO_SENSE;
2061 }
2062 #endif
2063
2064 if (!curlun) { // Unsupported LUNs are okay
2065 fsg->bad_lun_okay = 1;
2066 sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
2067 sdinfo = 0;
2068 valid = 0;
2069 } else {
2070 sd = curlun->sense_data;
2071 sdinfo = curlun->sense_data_info;
2072 valid = curlun->info_valid << 7;
2073 curlun->sense_data = SS_NO_SENSE;
2074 curlun->sense_data_info = 0;
2075 curlun->info_valid = 0;
2076 }
2077
2078 memset(buf, 0, 18);
2079 buf[0] = valid | 0x70; // Valid, current error
2080 buf[2] = SK(sd);
2081 put_be32(&buf[3], sdinfo); // Sense information
2082 buf[7] = 18 - 8; // Additional sense length
2083 buf[12] = ASC(sd);
2084 buf[13] = ASCQ(sd);
2085 return 18;
2086 }
2087
2088
2089 static int do_read_capacity(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2090 {
2091 struct lun *curlun = fsg->curlun;
2092 u32 lba = get_be32(&fsg->cmnd[2]);
2093 int pmi = fsg->cmnd[8];
2094 u8 *buf = (u8 *) bh->buf;
2095
2096 /* Check the PMI and LBA fields */
2097 if (pmi > 1 || (pmi == 0 && lba != 0)) {
2098 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2099 return -EINVAL;
2100 }
2101
2102 put_be32(&buf[0], curlun->num_sectors - 1); // Max logical block
2103 put_be32(&buf[4], 512); // Block length
2104 return 8;
2105 }
2106
2107
2108 static int do_mode_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2109 {
2110 struct lun *curlun = fsg->curlun;
2111 int mscmnd = fsg->cmnd[0];
2112 u8 *buf = (u8 *) bh->buf;
2113 u8 *buf0 = buf;
2114 int pc, page_code;
2115 int changeable_values, all_pages;
2116 int valid_page = 0;
2117 int len, limit;
2118
2119 if ((fsg->cmnd[1] & ~0x08) != 0) { // Mask away DBD
2120 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2121 return -EINVAL;
2122 }
2123 pc = fsg->cmnd[2] >> 6;
2124 page_code = fsg->cmnd[2] & 0x3f;
2125 if (pc == 3) {
2126 curlun->sense_data = SS_SAVING_PARAMETERS_NOT_SUPPORTED;
2127 return -EINVAL;
2128 }
2129 changeable_values = (pc == 1);
2130 all_pages = (page_code == 0x3f);
2131
2132 /* Write the mode parameter header. Fixed values are: default
2133 * medium type, no cache control (DPOFUA), and no block descriptors.
2134 * The only variable value is the WriteProtect bit. We will fill in
2135 * the mode data length later. */
2136 memset(buf, 0, 8);
2137 if (mscmnd == SC_MODE_SENSE_6) {
2138 buf[2] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA
2139 buf += 4;
2140 limit = 255;
2141 } else { // SC_MODE_SENSE_10
2142 buf[3] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA
2143 buf += 8;
2144 limit = 65535; // Should really be mod_data.buflen
2145 }
2146
2147 /* No block descriptors */
2148
2149 /* The mode pages, in numerical order. The only page we support
2150 * is the Caching page. */
2151 if (page_code == 0x08 || all_pages) {
2152 valid_page = 1;
2153 buf[0] = 0x08; // Page code
2154 buf[1] = 10; // Page length
2155 memset(buf+2, 0, 10); // None of the fields are changeable
2156
2157 if (!changeable_values) {
2158 buf[2] = 0x04; // Write cache enable,
2159 // Read cache not disabled
2160 // No cache retention priorities
2161 put_be16(&buf[4], 0xffff); // Don't disable prefetch
2162 // Minimum prefetch = 0
2163 put_be16(&buf[8], 0xffff); // Maximum prefetch
2164 put_be16(&buf[10], 0xffff); // Maximum prefetch ceiling
2165 }
2166 buf += 12;
2167 }
2168
2169 /* Check that a valid page was requested and the mode data length
2170 * isn't too long. */
2171 len = buf - buf0;
2172 if (!valid_page || len > limit) {
2173 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2174 return -EINVAL;
2175 }
2176
2177 /* Store the mode data length */
2178 if (mscmnd == SC_MODE_SENSE_6)
2179 buf0[0] = len - 1;
2180 else
2181 put_be16(buf0, len - 2);
2182 return len;
2183 }
2184
2185
2186 static int do_start_stop(struct fsg_dev *fsg)
2187 {
2188 struct lun *curlun = fsg->curlun;
2189 int loej, start;
2190
2191 if (!mod_data.removable) {
2192 curlun->sense_data = SS_INVALID_COMMAND;
2193 return -EINVAL;
2194 }
2195
2196 // int immed = fsg->cmnd[1] & 0x01;
2197 loej = fsg->cmnd[4] & 0x02;
2198 start = fsg->cmnd[4] & 0x01;
2199
2200 #ifdef CONFIG_USB_FILE_STORAGE_TEST
2201 if ((fsg->cmnd[1] & ~0x01) != 0 || // Mask away Immed
2202 (fsg->cmnd[4] & ~0x03) != 0) { // Mask LoEj, Start
2203 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2204 return -EINVAL;
2205 }
2206
2207 if (!start) {
2208
2209 /* Are we allowed to unload the media? */
2210 if (curlun->prevent_medium_removal) {
2211 LDBG(curlun, "unload attempt prevented\n");
2212 curlun->sense_data = SS_MEDIUM_REMOVAL_PREVENTED;
2213 return -EINVAL;
2214 }
2215 if (loej) { // Simulate an unload/eject
2216 up_read(&fsg->filesem);
2217 down_write(&fsg->filesem);
2218 close_backing_file(curlun);
2219 up_write(&fsg->filesem);
2220 down_read(&fsg->filesem);
2221 }
2222 } else {
2223
2224 /* Our emulation doesn't support mounting; the medium is
2225 * available for use as soon as it is loaded. */
2226 if (!backing_file_is_open(curlun)) {
2227 curlun->sense_data = SS_MEDIUM_NOT_PRESENT;
2228 return -EINVAL;
2229 }
2230 }
2231 #endif
2232 return 0;
2233 }
2234
2235
2236 static int do_prevent_allow(struct fsg_dev *fsg)
2237 {
2238 struct lun *curlun = fsg->curlun;
2239 int prevent;
2240
2241 if (!mod_data.removable) {
2242 curlun->sense_data = SS_INVALID_COMMAND;
2243 return -EINVAL;
2244 }
2245
2246 prevent = fsg->cmnd[4] & 0x01;
2247 if ((fsg->cmnd[4] & ~0x01) != 0) { // Mask away Prevent
2248 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2249 return -EINVAL;
2250 }
2251
2252 if (curlun->prevent_medium_removal && !prevent)
2253 fsync_sub(curlun);
2254 curlun->prevent_medium_removal = prevent;
2255 return 0;
2256 }
2257
2258
2259 static int do_read_format_capacities(struct fsg_dev *fsg,
2260 struct fsg_buffhd *bh)
2261 {
2262 struct lun *curlun = fsg->curlun;
2263 u8 *buf = (u8 *) bh->buf;
2264
2265 buf[0] = buf[1] = buf[2] = 0;
2266 buf[3] = 8; // Only the Current/Maximum Capacity Descriptor
2267 buf += 4;
2268
2269 put_be32(&buf[0], curlun->num_sectors); // Number of blocks
2270 put_be32(&buf[4], 512); // Block length
2271 buf[4] = 0x02; // Current capacity
2272 return 12;
2273 }
2274
2275
2276 static int do_mode_select(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2277 {
2278 struct lun *curlun = fsg->curlun;
2279
2280 /* We don't support MODE SELECT */
2281 curlun->sense_data = SS_INVALID_COMMAND;
2282 return -EINVAL;
2283 }
2284
2285
2286 /*-------------------------------------------------------------------------*/
2287
2288 static int halt_bulk_in_endpoint(struct fsg_dev *fsg)
2289 {
2290 int rc;
2291
2292 rc = fsg_set_halt(fsg, fsg->bulk_in);
2293 if (rc == -EAGAIN)
2294 VDBG(fsg, "delayed bulk-in endpoint halt\n");
2295 while (rc != 0) {
2296 if (rc != -EAGAIN) {
2297 WARN(fsg, "usb_ep_set_halt -> %d\n", rc);
2298 rc = 0;
2299 break;
2300 }
2301
2302 /* Wait for a short time and then try again */
2303 if (msleep_interruptible(100) != 0)
2304 return -EINTR;
2305 rc = usb_ep_set_halt(fsg->bulk_in);
2306 }
2307 return rc;
2308 }
2309
2310 static int pad_with_zeros(struct fsg_dev *fsg)
2311 {
2312 struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
2313 u32 nkeep = bh->inreq->length;
2314 u32 nsend;
2315 int rc;
2316
2317 bh->state = BUF_STATE_EMPTY; // For the first iteration
2318 fsg->usb_amount_left = nkeep + fsg->residue;
2319 while (fsg->usb_amount_left > 0) {
2320
2321 /* Wait for the next buffer to be free */
2322 while (bh->state != BUF_STATE_EMPTY) {
2323 rc = sleep_thread(fsg);
2324 if (rc)
2325 return rc;
2326 }
2327
2328 nsend = min(fsg->usb_amount_left, (u32) mod_data.buflen);
2329 memset(bh->buf + nkeep, 0, nsend - nkeep);
2330 bh->inreq->length = nsend;
2331 bh->inreq->zero = 0;
2332 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2333 &bh->inreq_busy, &bh->state);
2334 bh = fsg->next_buffhd_to_fill = bh->next;
2335 fsg->usb_amount_left -= nsend;
2336 nkeep = 0;
2337 }
2338 return 0;
2339 }
2340
2341 static int throw_away_data(struct fsg_dev *fsg)
2342 {
2343 struct fsg_buffhd *bh;
2344 u32 amount;
2345 int rc;
2346
2347 while ((bh = fsg->next_buffhd_to_drain)->state != BUF_STATE_EMPTY ||
2348 fsg->usb_amount_left > 0) {
2349
2350 /* Throw away the data in a filled buffer */
2351 if (bh->state == BUF_STATE_FULL) {
2352 smp_rmb();
2353 bh->state = BUF_STATE_EMPTY;
2354 fsg->next_buffhd_to_drain = bh->next;
2355
2356 /* A short packet or an error ends everything */
2357 if (bh->outreq->actual != bh->outreq->length ||
2358 bh->outreq->status != 0) {
2359 raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
2360 return -EINTR;
2361 }
2362 continue;
2363 }
2364
2365 /* Try to submit another request if we need one */
2366 bh = fsg->next_buffhd_to_fill;
2367 if (bh->state == BUF_STATE_EMPTY && fsg->usb_amount_left > 0) {
2368 amount = min(fsg->usb_amount_left,
2369 (u32) mod_data.buflen);
2370
2371 /* amount is always divisible by 512, hence by
2372 * the bulk-out maxpacket size */
2373 bh->outreq->length = bh->bulk_out_intended_length =
2374 amount;
2375 bh->outreq->short_not_ok = 1;
2376 start_transfer(fsg, fsg->bulk_out, bh->outreq,
2377 &bh->outreq_busy, &bh->state);
2378 fsg->next_buffhd_to_fill = bh->next;
2379 fsg->usb_amount_left -= amount;
2380 continue;
2381 }
2382
2383 /* Otherwise wait for something to happen */
2384 rc = sleep_thread(fsg);
2385 if (rc)
2386 return rc;
2387 }
2388 return 0;
2389 }
2390
2391
2392 static int finish_reply(struct fsg_dev *fsg)
2393 {
2394 struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
2395 int rc = 0;
2396
2397 switch (fsg->data_dir) {
2398 case DATA_DIR_NONE:
2399 break; // Nothing to send
2400
2401 /* If we don't know whether the host wants to read or write,
2402 * this must be CB or CBI with an unknown command. We mustn't
2403 * try to send or receive any data. So stall both bulk pipes
2404 * if we can and wait for a reset. */
2405 case DATA_DIR_UNKNOWN:
2406 if (mod_data.can_stall) {
2407 fsg_set_halt(fsg, fsg->bulk_out);
2408 rc = halt_bulk_in_endpoint(fsg);
2409 }
2410 break;
2411
2412 /* All but the last buffer of data must have already been sent */
2413 case DATA_DIR_TO_HOST:
2414 if (fsg->data_size == 0)
2415 ; // Nothing to send
2416
2417 /* If there's no residue, simply send the last buffer */
2418 else if (fsg->residue == 0) {
2419 bh->inreq->zero = 0;
2420 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2421 &bh->inreq_busy, &bh->state);
2422 fsg->next_buffhd_to_fill = bh->next;
2423 }
2424
2425 /* There is a residue. For CB and CBI, simply mark the end
2426 * of the data with a short packet. However, if we are
2427 * allowed to stall, there was no data at all (residue ==
2428 * data_size), and the command failed (invalid LUN or
2429 * sense data is set), then halt the bulk-in endpoint
2430 * instead. */
2431 else if (!transport_is_bbb()) {
2432 if (mod_data.can_stall &&
2433 fsg->residue == fsg->data_size &&
2434 (!fsg->curlun || fsg->curlun->sense_data != SS_NO_SENSE)) {
2435 bh->state = BUF_STATE_EMPTY;
2436 rc = halt_bulk_in_endpoint(fsg);
2437 } else {
2438 bh->inreq->zero = 1;
2439 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2440 &bh->inreq_busy, &bh->state);
2441 fsg->next_buffhd_to_fill = bh->next;
2442 }
2443 }
2444
2445 /* For Bulk-only, if we're allowed to stall then send the
2446 * short packet and halt the bulk-in endpoint. If we can't
2447 * stall, pad out the remaining data with 0's. */
2448 else {
2449 if (mod_data.can_stall) {
2450 bh->inreq->zero = 1;
2451 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2452 &bh->inreq_busy, &bh->state);
2453 fsg->next_buffhd_to_fill = bh->next;
2454 rc = halt_bulk_in_endpoint(fsg);
2455 } else
2456 rc = pad_with_zeros(fsg);
2457 }
2458 break;
2459
2460 /* We have processed all we want from the data the host has sent.
2461 * There may still be outstanding bulk-out requests. */
2462 case DATA_DIR_FROM_HOST:
2463 if (fsg->residue == 0)
2464 ; // Nothing to receive
2465
2466 /* Did the host stop sending unexpectedly early? */
2467 else if (fsg->short_packet_received) {
2468 raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
2469 rc = -EINTR;
2470 }
2471
2472 /* We haven't processed all the incoming data. Even though
2473 * we may be allowed to stall, doing so would cause a race.
2474 * The controller may already have ACK'ed all the remaining
2475 * bulk-out packets, in which case the host wouldn't see a
2476 * STALL. Not realizing the endpoint was halted, it wouldn't
2477 * clear the halt -- leading to problems later on. */
2478 #if 0
2479 else if (mod_data.can_stall) {
2480 fsg_set_halt(fsg, fsg->bulk_out);
2481 raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
2482 rc = -EINTR;
2483 }
2484 #endif
2485
2486 /* We can't stall. Read in the excess data and throw it
2487 * all away. */
2488 else
2489 rc = throw_away_data(fsg);
2490 break;
2491 }
2492 return rc;
2493 }
2494
2495
2496 static int send_status(struct fsg_dev *fsg)
2497 {
2498 struct lun *curlun = fsg->curlun;
2499 struct fsg_buffhd *bh;
2500 int rc;
2501 u8 status = USB_STATUS_PASS;
2502 u32 sd, sdinfo = 0;
2503
2504 /* Wait for the next buffer to become available */
2505 bh = fsg->next_buffhd_to_fill;
2506 while (bh->state != BUF_STATE_EMPTY) {
2507 rc = sleep_thread(fsg);
2508 if (rc)
2509 return rc;
2510 }
2511
2512 if (curlun) {
2513 sd = curlun->sense_data;
2514 sdinfo = curlun->sense_data_info;
2515 } else if (fsg->bad_lun_okay)
2516 sd = SS_NO_SENSE;
2517 else
2518 sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
2519
2520 if (fsg->phase_error) {
2521 DBG(fsg, "sending phase-error status\n");
2522 status = USB_STATUS_PHASE_ERROR;
2523 sd = SS_INVALID_COMMAND;
2524 } else if (sd != SS_NO_SENSE) {
2525 DBG(fsg, "sending command-failure status\n");
2526 status = USB_STATUS_FAIL;
2527 VDBG(fsg, " sense data: SK x%02x, ASC x%02x, ASCQ x%02x;"
2528 " info x%x\n",
2529 SK(sd), ASC(sd), ASCQ(sd), sdinfo);
2530 }
2531
2532 if (transport_is_bbb()) {
2533 struct bulk_cs_wrap *csw = bh->buf;
2534
2535 /* Store and send the Bulk-only CSW */
2536 csw->Signature = __constant_cpu_to_le32(USB_BULK_CS_SIG);
2537 csw->Tag = fsg->tag;
2538 csw->Residue = cpu_to_le32(fsg->residue);
2539 csw->Status = status;
2540
2541 bh->inreq->length = USB_BULK_CS_WRAP_LEN;
2542 bh->inreq->zero = 0;
2543 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2544 &bh->inreq_busy, &bh->state);
2545
2546 } else if (mod_data.transport_type == USB_PR_CB) {
2547
2548 /* Control-Bulk transport has no status phase! */
2549 return 0;
2550
2551 } else { // USB_PR_CBI
2552 struct interrupt_data *buf = bh->buf;
2553
2554 /* Store and send the Interrupt data. UFI sends the ASC
2555 * and ASCQ bytes. Everything else sends a Type (which
2556 * is always 0) and the status Value. */
2557 if (mod_data.protocol_type == USB_SC_UFI) {
2558 buf->bType = ASC(sd);
2559 buf->bValue = ASCQ(sd);
2560 } else {
2561 buf->bType = 0;
2562 buf->bValue = status;
2563 }
2564 fsg->intreq->length = CBI_INTERRUPT_DATA_LEN;
2565
2566 fsg->intr_buffhd = bh; // Point to the right buffhd
2567 fsg->intreq->buf = bh->inreq->buf;
2568 fsg->intreq->context = bh;
2569 start_transfer(fsg, fsg->intr_in, fsg->intreq,
2570 &fsg->intreq_busy, &bh->state);
2571 }
2572
2573 fsg->next_buffhd_to_fill = bh->next;
2574 return 0;
2575 }
2576
2577
2578 /*-------------------------------------------------------------------------*/
2579
2580 /* Check whether the command is properly formed and whether its data size
2581 * and direction agree with the values we already have. */
2582 static int check_command(struct fsg_dev *fsg, int cmnd_size,
2583 enum data_direction data_dir, unsigned int mask,
2584 int needs_medium, const char *name)
2585 {
2586 int i;
2587 int lun = fsg->cmnd[1] >> 5;
2588 static const char dirletter[4] = {'u', 'o', 'i', 'n'};
2589 char hdlen[20];
2590 struct lun *curlun;
2591
2592 /* Adjust the expected cmnd_size for protocol encapsulation padding.
2593 * Transparent SCSI doesn't pad. */
2594 if (protocol_is_scsi())
2595 ;
2596
2597 /* There's some disagreement as to whether RBC pads commands or not.
2598 * We'll play it safe and accept either form. */
2599 else if (mod_data.protocol_type == USB_SC_RBC) {
2600 if (fsg->cmnd_size == 12)
2601 cmnd_size = 12;
2602
2603 /* All the other protocols pad to 12 bytes */
2604 } else
2605 cmnd_size = 12;
2606
2607 hdlen[0] = 0;
2608 if (fsg->data_dir != DATA_DIR_UNKNOWN)
2609 sprintf(hdlen, ", H%c=%u", dirletter[(int) fsg->data_dir],
2610 fsg->data_size);
2611 VDBG(fsg, "SCSI command: %s; Dc=%d, D%c=%u; Hc=%d%s\n",
2612 name, cmnd_size, dirletter[(int) data_dir],
2613 fsg->data_size_from_cmnd, fsg->cmnd_size, hdlen);
2614
2615 /* We can't reply at all until we know the correct data direction
2616 * and size. */
2617 if (fsg->data_size_from_cmnd == 0)
2618 data_dir = DATA_DIR_NONE;
2619 if (fsg->data_dir == DATA_DIR_UNKNOWN) { // CB or CBI
2620 fsg->data_dir = data_dir;
2621 fsg->data_size = fsg->data_size_from_cmnd;
2622
2623 } else { // Bulk-only
2624 if (fsg->data_size < fsg->data_size_from_cmnd) {
2625
2626 /* Host data size < Device data size is a phase error.
2627 * Carry out the command, but only transfer as much
2628 * as we are allowed. */
2629 fsg->data_size_from_cmnd = fsg->data_size;
2630 fsg->phase_error = 1;
2631 }
2632 }
2633 fsg->residue = fsg->usb_amount_left = fsg->data_size;
2634
2635 /* Conflicting data directions is a phase error */
2636 if (fsg->data_dir != data_dir && fsg->data_size_from_cmnd > 0) {
2637 fsg->phase_error = 1;
2638 return -EINVAL;
2639 }
2640
2641 /* Verify the length of the command itself */
2642 if (cmnd_size != fsg->cmnd_size) {
2643
2644 /* Special case workaround: MS-Windows issues REQUEST SENSE
2645 * with cbw->Length == 12 (it should be 6). */
2646 if (fsg->cmnd[0] == SC_REQUEST_SENSE && fsg->cmnd_size == 12)
2647 cmnd_size = fsg->cmnd_size;
2648 else {
2649 fsg->phase_error = 1;
2650 return -EINVAL;
2651 }
2652 }
2653
2654 /* Check that the LUN values are consistent */
2655 if (transport_is_bbb()) {
2656 if (fsg->lun != lun)
2657 DBG(fsg, "using LUN %d from CBW, "
2658 "not LUN %d from CDB\n",
2659 fsg->lun, lun);
2660 } else
2661 fsg->lun = lun; // Use LUN from the command
2662
2663 /* Check the LUN */
2664 if (fsg->lun >= 0 && fsg->lun < fsg->nluns) {
2665 fsg->curlun = curlun = &fsg->luns[fsg->lun];
2666 if (fsg->cmnd[0] != SC_REQUEST_SENSE) {
2667 curlun->sense_data = SS_NO_SENSE;
2668 curlun->sense_data_info = 0;
2669 curlun->info_valid = 0;
2670 }
2671 } else {
2672 fsg->curlun = curlun = NULL;
2673 fsg->bad_lun_okay = 0;
2674
2675 /* INQUIRY and REQUEST SENSE commands are explicitly allowed
2676 * to use unsupported LUNs; all others may not. */
2677 if (fsg->cmnd[0] != SC_INQUIRY &&
2678 fsg->cmnd[0] != SC_REQUEST_SENSE) {
2679 DBG(fsg, "unsupported LUN %d\n", fsg->lun);
2680 return -EINVAL;
2681 }
2682 }
2683
2684 /* If a unit attention condition exists, only INQUIRY and
2685 * REQUEST SENSE commands are allowed; anything else must fail. */
2686 if (curlun && curlun->unit_attention_data != SS_NO_SENSE &&
2687 fsg->cmnd[0] != SC_INQUIRY &&
2688 fsg->cmnd[0] != SC_REQUEST_SENSE) {
2689 curlun->sense_data = curlun->unit_attention_data;
2690 curlun->unit_attention_data = SS_NO_SENSE;
2691 return -EINVAL;
2692 }
2693
2694 /* Check that only command bytes listed in the mask are non-zero */
2695 fsg->cmnd[1] &= 0x1f; // Mask away the LUN
2696 for (i = 1; i < cmnd_size; ++i) {
2697 if (fsg->cmnd[i] && !(mask & (1 << i))) {
2698 if (curlun)
2699 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2700 return -EINVAL;
2701 }
2702 }
2703
2704 /* If the medium isn't mounted and the command needs to access
2705 * it, return an error. */
2706 if (curlun && !backing_file_is_open(curlun) && needs_medium) {
2707 curlun->sense_data = SS_MEDIUM_NOT_PRESENT;
2708 return -EINVAL;
2709 }
2710
2711 return 0;
2712 }
2713
2714
2715 static int do_scsi_command(struct fsg_dev *fsg)
2716 {
2717 struct fsg_buffhd *bh;
2718 int rc;
2719 int reply = -EINVAL;
2720 int i;
2721 static char unknown[16];
2722
2723 dump_cdb(fsg);
2724
2725 /* Wait for the next buffer to become available for data or status */
2726 bh = fsg->next_buffhd_to_drain = fsg->next_buffhd_to_fill;
2727 while (bh->state != BUF_STATE_EMPTY) {
2728 rc = sleep_thread(fsg);
2729 if (rc)
2730 return rc;
2731 }
2732 fsg->phase_error = 0;
2733 fsg->short_packet_received = 0;
2734
2735 down_read(&fsg->filesem); // We're using the backing file
2736 switch (fsg->cmnd[0]) {
2737
2738 case SC_INQUIRY:
2739 fsg->data_size_from_cmnd = fsg->cmnd[4];
2740 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2741 (1<<4), 0,
2742 "INQUIRY")) == 0)
2743 reply = do_inquiry(fsg, bh);
2744 break;
2745
2746 case SC_MODE_SELECT_6:
2747 fsg->data_size_from_cmnd = fsg->cmnd[4];
2748 if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST,
2749 (1<<1) | (1<<4), 0,
2750 "MODE SELECT(6)")) == 0)
2751 reply = do_mode_select(fsg, bh);
2752 break;
2753
2754 case SC_MODE_SELECT_10:
2755 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
2756 if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST,
2757 (1<<1) | (3<<7), 0,
2758 "MODE SELECT(10)")) == 0)
2759 reply = do_mode_select(fsg, bh);
2760 break;
2761
2762 case SC_MODE_SENSE_6:
2763 fsg->data_size_from_cmnd = fsg->cmnd[4];
2764 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2765 (1<<1) | (1<<2) | (1<<4), 0,
2766 "MODE SENSE(6)")) == 0)
2767 reply = do_mode_sense(fsg, bh);
2768 break;
2769
2770 case SC_MODE_SENSE_10:
2771 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
2772 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2773 (1<<1) | (1<<2) | (3<<7), 0,
2774 "MODE SENSE(10)")) == 0)
2775 reply = do_mode_sense(fsg, bh);
2776 break;
2777
2778 case SC_PREVENT_ALLOW_MEDIUM_REMOVAL:
2779 fsg->data_size_from_cmnd = 0;
2780 if ((reply = check_command(fsg, 6, DATA_DIR_NONE,
2781 (1<<4), 0,
2782 "PREVENT-ALLOW MEDIUM REMOVAL")) == 0)
2783 reply = do_prevent_allow(fsg);
2784 break;
2785
2786 case SC_READ_6:
2787 i = fsg->cmnd[4];
2788 fsg->data_size_from_cmnd = (i == 0 ? 256 : i) << 9;
2789 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2790 (7<<1) | (1<<4), 1,
2791 "READ(6)")) == 0)
2792 reply = do_read(fsg);
2793 break;
2794
2795 case SC_READ_10:
2796 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]) << 9;
2797 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2798 (1<<1) | (0xf<<2) | (3<<7), 1,
2799 "READ(10)")) == 0)
2800 reply = do_read(fsg);
2801 break;
2802
2803 case SC_READ_12:
2804 fsg->data_size_from_cmnd = get_be32(&fsg->cmnd[6]) << 9;
2805 if ((reply = check_command(fsg, 12, DATA_DIR_TO_HOST,
2806 (1<<1) | (0xf<<2) | (0xf<<6), 1,
2807 "READ(12)")) == 0)
2808 reply = do_read(fsg);
2809 break;
2810
2811 case SC_READ_CAPACITY:
2812 fsg->data_size_from_cmnd = 8;
2813 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2814 (0xf<<2) | (1<<8), 1,
2815 "READ CAPACITY")) == 0)
2816 reply = do_read_capacity(fsg, bh);
2817 break;
2818
2819 case SC_READ_FORMAT_CAPACITIES:
2820 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
2821 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2822 (3<<7), 1,
2823 "READ FORMAT CAPACITIES")) == 0)
2824 reply = do_read_format_capacities(fsg, bh);
2825 break;
2826
2827 case SC_REQUEST_SENSE:
2828 fsg->data_size_from_cmnd = fsg->cmnd[4];
2829 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2830 (1<<4), 0,
2831 "REQUEST SENSE")) == 0)
2832 reply = do_request_sense(fsg, bh);
2833 break;
2834
2835 case SC_START_STOP_UNIT:
2836 fsg->data_size_from_cmnd = 0;
2837 if ((reply = check_command(fsg, 6, DATA_DIR_NONE,
2838 (1<<1) | (1<<4), 0,
2839 "START-STOP UNIT")) == 0)
2840 reply = do_start_stop(fsg);
2841 break;
2842
2843 case SC_SYNCHRONIZE_CACHE:
2844 fsg->data_size_from_cmnd = 0;
2845 if ((reply = check_command(fsg, 10, DATA_DIR_NONE,
2846 (0xf<<2) | (3<<7), 1,
2847 "SYNCHRONIZE CACHE")) == 0)
2848 reply = do_synchronize_cache(fsg);
2849 break;
2850
2851 case SC_TEST_UNIT_READY:
2852 fsg->data_size_from_cmnd = 0;
2853 reply = check_command(fsg, 6, DATA_DIR_NONE,
2854 0, 1,
2855 "TEST UNIT READY");
2856 break;
2857
2858 /* Although optional, this command is used by MS-Windows. We
2859 * support a minimal version: BytChk must be 0. */
2860 case SC_VERIFY:
2861 fsg->data_size_from_cmnd = 0;
2862 if ((reply = check_command(fsg, 10, DATA_DIR_NONE,
2863 (1<<1) | (0xf<<2) | (3<<7), 1,
2864 "VERIFY")) == 0)
2865 reply = do_verify(fsg);
2866 break;
2867
2868 case SC_WRITE_6:
2869 i = fsg->cmnd[4];
2870 fsg->data_size_from_cmnd = (i == 0 ? 256 : i) << 9;
2871 if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST,
2872 (7<<1) | (1<<4), 1,
2873 "WRITE(6)")) == 0)
2874 reply = do_write(fsg);
2875 break;
2876
2877 case SC_WRITE_10:
2878 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]) << 9;
2879 if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST,
2880 (1<<1) | (0xf<<2) | (3<<7), 1,
2881 "WRITE(10)")) == 0)
2882 reply = do_write(fsg);
2883 break;
2884
2885 case SC_WRITE_12:
2886 fsg->data_size_from_cmnd = get_be32(&fsg->cmnd[6]) << 9;
2887 if ((reply = check_command(fsg, 12, DATA_DIR_FROM_HOST,
2888 (1<<1) | (0xf<<2) | (0xf<<6), 1,
2889 "WRITE(12)")) == 0)
2890 reply = do_write(fsg);
2891 break;
2892
2893 /* Some mandatory commands that we recognize but don't implement.
2894 * They don't mean much in this setting. It's left as an exercise
2895 * for anyone interested to implement RESERVE and RELEASE in terms
2896 * of Posix locks. */
2897 case SC_FORMAT_UNIT:
2898 case SC_RELEASE:
2899 case SC_RESERVE:
2900 case SC_SEND_DIAGNOSTIC:
2901 // Fall through
2902
2903 default:
2904 fsg->data_size_from_cmnd = 0;
2905 sprintf(unknown, "Unknown x%02x", fsg->cmnd[0]);
2906 if ((reply = check_command(fsg, fsg->cmnd_size,
2907 DATA_DIR_UNKNOWN, 0xff, 0, unknown)) == 0) {
2908 fsg->curlun->sense_data = SS_INVALID_COMMAND;
2909 reply = -EINVAL;
2910 }
2911 break;
2912 }
2913 up_read(&fsg->filesem);
2914
2915 if (reply == -EINTR || signal_pending(current))
2916 return -EINTR;
2917
2918 /* Set up the single reply buffer for finish_reply() */
2919 if (reply == -EINVAL)
2920 reply = 0; // Error reply length
2921 if (reply >= 0 && fsg->data_dir == DATA_DIR_TO_HOST) {
2922 reply = min((u32) reply, fsg->data_size_from_cmnd);
2923 bh->inreq->length = reply;
2924 bh->state = BUF_STATE_FULL;
2925 fsg->residue -= reply;
2926 } // Otherwise it's already set
2927
2928 return 0;
2929 }
2930
2931
2932 /*-------------------------------------------------------------------------*/
2933
2934 static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2935 {
2936 struct usb_request *req = bh->outreq;
2937 struct bulk_cb_wrap *cbw = req->buf;
2938
2939 /* Was this a real packet? */
2940 if (req->status)
2941 return -EINVAL;
2942
2943 /* Is the CBW valid? */
2944 if (req->actual != USB_BULK_CB_WRAP_LEN ||
2945 cbw->Signature != __constant_cpu_to_le32(
2946 USB_BULK_CB_SIG)) {
2947 DBG(fsg, "invalid CBW: len %u sig 0x%x\n",
2948 req->actual,
2949 le32_to_cpu(cbw->Signature));
2950
2951 /* The Bulk-only spec says we MUST stall the bulk pipes!
2952 * If we want to avoid stalls, set a flag so that we will
2953 * clear the endpoint halts at the next reset. */
2954 if (!mod_data.can_stall)
2955 set_bit(CLEAR_BULK_HALTS, &fsg->atomic_bitflags);
2956 fsg_set_halt(fsg, fsg->bulk_out);
2957 halt_bulk_in_endpoint(fsg);
2958 return -EINVAL;
2959 }
2960
2961 /* Is the CBW meaningful? */
2962 if (cbw->Lun >= MAX_LUNS || cbw->Flags & ~USB_BULK_IN_FLAG ||
2963 cbw->Length <= 0 || cbw->Length > MAX_COMMAND_SIZE) {
2964 DBG(fsg, "non-meaningful CBW: lun = %u, flags = 0x%x, "
2965 "cmdlen %u\n",
2966 cbw->Lun, cbw->Flags, cbw->Length);
2967
2968 /* We can do anything we want here, so let's stall the
2969 * bulk pipes if we are allowed to. */
2970 if (mod_data.can_stall) {
2971 fsg_set_halt(fsg, fsg->bulk_out);
2972 halt_bulk_in_endpoint(fsg);
2973 }
2974 return -EINVAL;
2975 }
2976
2977 /* Save the command for later */
2978 fsg->cmnd_size = cbw->Length;
2979 memcpy(fsg->cmnd, cbw->CDB, fsg->cmnd_size);
2980 if (cbw->Flags & USB_BULK_IN_FLAG)
2981 fsg->data_dir = DATA_DIR_TO_HOST;
2982 else
2983 fsg->data_dir = DATA_DIR_FROM_HOST;
2984 fsg->data_size = le32_to_cpu(cbw->DataTransferLength);
2985 if (fsg->data_size == 0)
2986 fsg->data_dir = DATA_DIR_NONE;
2987 fsg->lun = cbw->Lun;
2988 fsg->tag = cbw->Tag;
2989 return 0;
2990 }
2991
2992
2993 static int get_next_command(struct fsg_dev *fsg)
2994 {
2995 struct fsg_buffhd *bh;
2996 int rc = 0;
2997
2998 if (transport_is_bbb()) {
2999
3000 /* Wait for the next buffer to become available */
3001 bh = fsg->next_buffhd_to_fill;
3002 while (bh->state != BUF_STATE_EMPTY) {
3003 rc = sleep_thread(fsg);
3004 if (rc)
3005 return rc;
3006 }
3007
3008 /* Queue a request to read a Bulk-only CBW */
3009 set_bulk_out_req_length(fsg, bh, USB_BULK_CB_WRAP_LEN);
3010 bh->outreq->short_not_ok = 1;
3011 start_transfer(fsg, fsg->bulk_out, bh->outreq,
3012 &bh->outreq_busy, &bh->state);
3013
3014 /* We will drain the buffer in software, which means we
3015 * can reuse it for the next filling. No need to advance
3016 * next_buffhd_to_fill. */
3017
3018 /* Wait for the CBW to arrive */
3019 while (bh->state != BUF_STATE_FULL) {
3020 rc = sleep_thread(fsg);
3021 if (rc)
3022 return rc;
3023 }
3024 smp_rmb();
3025 rc = received_cbw(fsg, bh);
3026 bh->state = BUF_STATE_EMPTY;
3027
3028 } else { // USB_PR_CB or USB_PR_CBI
3029
3030 /* Wait for the next command to arrive */
3031 while (fsg->cbbuf_cmnd_size == 0) {
3032 rc = sleep_thread(fsg);
3033 if (rc)
3034 return rc;
3035 }
3036
3037 /* Is the previous status interrupt request still busy?
3038 * The host is allowed to skip reading the status,
3039 * so we must cancel it. */
3040 if (fsg->intreq_busy)
3041 usb_ep_dequeue(fsg->intr_in, fsg->intreq);
3042
3043 /* Copy the command and mark the buffer empty */
3044 fsg->data_dir = DATA_DIR_UNKNOWN;
3045 spin_lock_irq(&fsg->lock);
3046 fsg->cmnd_size = fsg->cbbuf_cmnd_size;
3047 memcpy(fsg->cmnd, fsg->cbbuf_cmnd, fsg->cmnd_size);
3048 fsg->cbbuf_cmnd_size = 0;
3049 spin_unlock_irq(&fsg->lock);
3050 }
3051 return rc;
3052 }
3053
3054
3055 /*-------------------------------------------------------------------------*/
3056
3057 static int enable_endpoint(struct fsg_dev *fsg, struct usb_ep *ep,
3058 const struct usb_endpoint_descriptor *d)
3059 {
3060 int rc;
3061
3062 ep->driver_data = fsg;
3063 rc = usb_ep_enable(ep, d);
3064 if (rc)
3065 ERROR(fsg, "can't enable %s, result %d\n", ep->name, rc);
3066 return rc;
3067 }
3068
3069 static int alloc_request(struct fsg_dev *fsg, struct usb_ep *ep,
3070 struct usb_request **preq)
3071 {
3072 *preq = usb_ep_alloc_request(ep, GFP_ATOMIC);
3073 if (*preq)
3074 return 0;
3075 ERROR(fsg, "can't allocate request for %s\n", ep->name);
3076 return -ENOMEM;
3077 }
3078
3079 /*
3080 * Reset interface setting and re-init endpoint state (toggle etc).
3081 * Call with altsetting < 0 to disable the interface. The only other
3082 * available altsetting is 0, which enables the interface.
3083 */
3084 static int do_set_interface(struct fsg_dev *fsg, int altsetting)
3085 {
3086 int rc = 0;
3087 int i;
3088 const struct usb_endpoint_descriptor *d;
3089
3090 if (fsg->running)
3091 DBG(fsg, "reset interface\n");
3092
3093 reset:
3094 /* Deallocate the requests */
3095 for (i = 0; i < NUM_BUFFERS; ++i) {
3096 struct fsg_buffhd *bh = &fsg->buffhds[i];
3097
3098 if (bh->inreq) {
3099 usb_ep_free_request(fsg->bulk_in, bh->inreq);
3100 bh->inreq = NULL;
3101 }
3102 if (bh->outreq) {
3103 usb_ep_free_request(fsg->bulk_out, bh->outreq);
3104 bh->outreq = NULL;
3105 }
3106 }
3107 if (fsg->intreq) {
3108 usb_ep_free_request(fsg->intr_in, fsg->intreq);
3109 fsg->intreq = NULL;
3110 }
3111
3112 /* Disable the endpoints */
3113 if (fsg->bulk_in_enabled) {
3114 usb_ep_disable(fsg->bulk_in);
3115 fsg->bulk_in_enabled = 0;
3116 }
3117 if (fsg->bulk_out_enabled) {
3118 usb_ep_disable(fsg->bulk_out);
3119 fsg->bulk_out_enabled = 0;
3120 }
3121 if (fsg->intr_in_enabled) {
3122 usb_ep_disable(fsg->intr_in);
3123 fsg->intr_in_enabled = 0;
3124 }
3125
3126 fsg->running = 0;
3127 if (altsetting < 0 || rc != 0)
3128 return rc;
3129
3130 DBG(fsg, "set interface %d\n", altsetting);
3131
3132 /* Enable the endpoints */
3133 d = ep_desc(fsg->gadget, &fs_bulk_in_desc, &hs_bulk_in_desc);
3134 if ((rc = enable_endpoint(fsg, fsg->bulk_in, d)) != 0)
3135 goto reset;
3136 fsg->bulk_in_enabled = 1;
3137
3138 d = ep_desc(fsg->gadget, &fs_bulk_out_desc, &hs_bulk_out_desc);
3139 if ((rc = enable_endpoint(fsg, fsg->bulk_out, d)) != 0)
3140 goto reset;
3141 fsg->bulk_out_enabled = 1;
3142 fsg->bulk_out_maxpacket = le16_to_cpu(d->wMaxPacketSize);
3143
3144 if (transport_is_cbi()) {
3145 d = ep_desc(fsg->gadget, &fs_intr_in_desc, &hs_intr_in_desc);
3146 if ((rc = enable_endpoint(fsg, fsg->intr_in, d)) != 0)
3147 goto reset;
3148 fsg->intr_in_enabled = 1;
3149 }
3150
3151 /* Allocate the requests */
3152 for (i = 0; i < NUM_BUFFERS; ++i) {
3153 struct fsg_buffhd *bh = &fsg->buffhds[i];
3154
3155 if ((rc = alloc_request(fsg, fsg->bulk_in, &bh->inreq)) != 0)
3156 goto reset;
3157 if ((rc = alloc_request(fsg, fsg->bulk_out, &bh->outreq)) != 0)
3158 goto reset;
3159 bh->inreq->buf = bh->outreq->buf = bh->buf;
3160 bh->inreq->context = bh->outreq->context = bh;
3161 bh->inreq->complete = bulk_in_complete;
3162 bh->outreq->complete = bulk_out_complete;
3163 }
3164 if (transport_is_cbi()) {
3165 if ((rc = alloc_request(fsg, fsg->intr_in, &fsg->intreq)) != 0)
3166 goto reset;
3167 fsg->intreq->complete = intr_in_complete;
3168 }
3169
3170 fsg->running = 1;
3171 for (i = 0; i < fsg->nluns; ++i)
3172 fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED;
3173 return rc;
3174 }
3175
3176
3177 /*
3178 * Change our operational configuration. This code must agree with the code
3179 * that returns config descriptors, and with interface altsetting code.
3180 *
3181 * It's also responsible for power management interactions. Some
3182 * configurations might not work with our current power sources.
3183 * For now we just assume the gadget is always self-powered.
3184 */
3185 static int do_set_config(struct fsg_dev *fsg, u8 new_config)
3186 {
3187 int rc = 0;
3188
3189 /* Disable the single interface */
3190 if (fsg->config != 0) {
3191 DBG(fsg, "reset config\n");
3192 fsg->config = 0;
3193 rc = do_set_interface(fsg, -1);
3194 }
3195
3196 /* Enable the interface */
3197 if (new_config != 0) {
3198 fsg->config = new_config;
3199 if ((rc = do_set_interface(fsg, 0)) != 0)
3200 fsg->config = 0; // Reset on errors
3201 else {
3202 char *speed;
3203
3204 switch (fsg->gadget->speed) {
3205 case USB_SPEED_LOW: speed = "low"; break;
3206 case USB_SPEED_FULL: speed = "full"; break;
3207 case USB_SPEED_HIGH: speed = "high"; break;
3208 default: speed = "?"; break;
3209 }
3210 INFO(fsg, "%s speed config #%d\n", speed, fsg->config);
3211 }
3212 }
3213 return rc;
3214 }
3215
3216
3217 /*-------------------------------------------------------------------------*/
3218
3219 static void handle_exception(struct fsg_dev *fsg)
3220 {
3221 siginfo_t info;
3222 int sig;
3223 int i;
3224 int num_active;
3225 struct fsg_buffhd *bh;
3226 enum fsg_state old_state;
3227 u8 new_config;
3228 struct lun *curlun;
3229 unsigned int exception_req_tag;
3230 int rc;
3231
3232 /* Clear the existing signals. Anything but SIGUSR1 is converted
3233 * into a high-priority EXIT exception. */
3234 for (;;) {
3235 sig = dequeue_signal_lock(current, &current->blocked, &info);
3236 if (!sig)
3237 break;
3238 if (sig != SIGUSR1) {
3239 if (fsg->state < FSG_STATE_EXIT)
3240 DBG(fsg, "Main thread exiting on signal\n");
3241 raise_exception(fsg, FSG_STATE_EXIT);
3242 }
3243 }
3244
3245 /* Cancel all the pending transfers */
3246 if (fsg->intreq_busy)
3247 usb_ep_dequeue(fsg->intr_in, fsg->intreq);
3248 for (i = 0; i < NUM_BUFFERS; ++i) {
3249 bh = &fsg->buffhds[i];
3250 if (bh->inreq_busy)
3251 usb_ep_dequeue(fsg->bulk_in, bh->inreq);
3252 if (bh->outreq_busy)
3253 usb_ep_dequeue(fsg->bulk_out, bh->outreq);
3254 }
3255
3256 /* Wait until everything is idle */
3257 for (;;) {
3258 num_active = fsg->intreq_busy;
3259 for (i = 0; i < NUM_BUFFERS; ++i) {
3260 bh = &fsg->buffhds[i];
3261 num_active += bh->inreq_busy + bh->outreq_busy;
3262 }
3263 if (num_active == 0)
3264 break;
3265 if (sleep_thread(fsg))
3266 return;
3267 }
3268
3269 /* Clear out the controller's fifos */
3270 if (fsg->bulk_in_enabled)
3271 usb_ep_fifo_flush(fsg->bulk_in);
3272 if (fsg->bulk_out_enabled)
3273 usb_ep_fifo_flush(fsg->bulk_out);
3274 if (fsg->intr_in_enabled)
3275 usb_ep_fifo_flush(fsg->intr_in);
3276
3277 /* Reset the I/O buffer states and pointers, the SCSI
3278 * state, and the exception. Then invoke the handler. */
3279 spin_lock_irq(&fsg->lock);
3280
3281 for (i = 0; i < NUM_BUFFERS; ++i) {
3282 bh = &fsg->buffhds[i];
3283 bh->state = BUF_STATE_EMPTY;
3284 }
3285 fsg->next_buffhd_to_fill = fsg->next_buffhd_to_drain =
3286 &fsg->buffhds[0];
3287
3288 exception_req_tag = fsg->exception_req_tag;
3289 new_config = fsg->new_config;
3290 old_state = fsg->state;
3291
3292 if (old_state == FSG_STATE_ABORT_BULK_OUT)
3293 fsg->state = FSG_STATE_STATUS_PHASE;
3294 else {
3295 for (i = 0; i < fsg->nluns; ++i) {
3296 curlun = &fsg->luns[i];
3297 curlun->prevent_medium_removal = 0;
3298 curlun->sense_data = curlun->unit_attention_data =
3299 SS_NO_SENSE;
3300 curlun->sense_data_info = 0;
3301 curlun->info_valid = 0;
3302 }
3303 fsg->state = FSG_STATE_IDLE;
3304 }
3305 spin_unlock_irq(&fsg->lock);
3306
3307 /* Carry out any extra actions required for the exception */
3308 switch (old_state) {
3309 default:
3310 break;
3311
3312 case FSG_STATE_ABORT_BULK_OUT:
3313 send_status(fsg);
3314 spin_lock_irq(&fsg->lock);
3315 if (fsg->state == FSG_STATE_STATUS_PHASE)
3316 fsg->state = FSG_STATE_IDLE;
3317 spin_unlock_irq(&fsg->lock);
3318 break;
3319
3320 case FSG_STATE_RESET:
3321 /* In case we were forced against our will to halt a
3322 * bulk endpoint, clear the halt now. (The SuperH UDC
3323 * requires this.) */
3324 if (test_and_clear_bit(CLEAR_BULK_HALTS,
3325 &fsg->atomic_bitflags)) {
3326 usb_ep_clear_halt(fsg->bulk_in);
3327 usb_ep_clear_halt(fsg->bulk_out);
3328 }
3329
3330 if (transport_is_bbb()) {
3331 if (fsg->ep0_req_tag == exception_req_tag)
3332 ep0_queue(fsg); // Complete the status stage
3333
3334 } else if (transport_is_cbi())
3335 send_status(fsg); // Status by interrupt pipe
3336
3337 /* Technically this should go here, but it would only be
3338 * a waste of time. Ditto for the INTERFACE_CHANGE and
3339 * CONFIG_CHANGE cases. */
3340 // for (i = 0; i < fsg->nluns; ++i)
3341 // fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED;
3342 break;
3343
3344 case FSG_STATE_INTERFACE_CHANGE:
3345 rc = do_set_interface(fsg, 0);
3346 if (fsg->ep0_req_tag != exception_req_tag)
3347 break;
3348 if (rc != 0) // STALL on errors
3349 fsg_set_halt(fsg, fsg->ep0);
3350 else // Complete the status stage
3351 ep0_queue(fsg);
3352 break;
3353
3354 case FSG_STATE_CONFIG_CHANGE:
3355 rc = do_set_config(fsg, new_config);
3356 if (fsg->ep0_req_tag != exception_req_tag)
3357 break;
3358 if (rc != 0) // STALL on errors
3359 fsg_set_halt(fsg, fsg->ep0);
3360 else // Complete the status stage
3361 ep0_queue(fsg);
3362 break;
3363
3364 case FSG_STATE_DISCONNECT:
3365 fsync_all(fsg);
3366 do_set_config(fsg, 0); // Unconfigured state
3367 break;
3368
3369 case FSG_STATE_EXIT:
3370 case FSG_STATE_TERMINATED:
3371 do_set_config(fsg, 0); // Free resources
3372 spin_lock_irq(&fsg->lock);
3373 fsg->state = FSG_STATE_TERMINATED; // Stop the thread
3374 spin_unlock_irq(&fsg->lock);
3375 break;
3376 }
3377 }
3378
3379
3380 /*-------------------------------------------------------------------------*/
3381
3382 static int fsg_main_thread(void *fsg_)
3383 {
3384 struct fsg_dev *fsg = fsg_;
3385
3386 /* Allow the thread to be killed by a signal, but set the signal mask
3387 * to block everything but INT, TERM, KILL, and USR1. */
3388 allow_signal(SIGINT);
3389 allow_signal(SIGTERM);
3390 allow_signal(SIGKILL);
3391 allow_signal(SIGUSR1);
3392
3393 /* Allow the thread to be frozen */
3394 set_freezable();
3395
3396 /* Arrange for userspace references to be interpreted as kernel
3397 * pointers. That way we can pass a kernel pointer to a routine
3398 * that expects a __user pointer and it will work okay. */
3399 set_fs(get_ds());
3400
3401 /* The main loop */
3402 while (fsg->state != FSG_STATE_TERMINATED) {
3403 if (exception_in_progress(fsg) || signal_pending(current)) {
3404 handle_exception(fsg);
3405 continue;
3406 }
3407
3408 if (!fsg->running) {
3409 sleep_thread(fsg);
3410 continue;
3411 }
3412
3413 if (get_next_command(fsg))
3414 continue;
3415
3416 spin_lock_irq(&fsg->lock);
3417 if (!exception_in_progress(fsg))
3418 fsg->state = FSG_STATE_DATA_PHASE;
3419 spin_unlock_irq(&fsg->lock);
3420
3421 if (do_scsi_command(fsg) || finish_reply(fsg))
3422 continue;
3423
3424 spin_lock_irq(&fsg->lock);
3425 if (!exception_in_progress(fsg))
3426 fsg->state = FSG_STATE_STATUS_PHASE;
3427 spin_unlock_irq(&fsg->lock);
3428
3429 if (send_status(fsg))
3430 continue;
3431
3432 spin_lock_irq(&fsg->lock);
3433 if (!exception_in_progress(fsg))
3434 fsg->state = FSG_STATE_IDLE;
3435 spin_unlock_irq(&fsg->lock);
3436 }
3437
3438 spin_lock_irq(&fsg->lock);
3439 fsg->thread_task = NULL;
3440 spin_unlock_irq(&fsg->lock);
3441
3442 /* In case we are exiting because of a signal, unregister the
3443 * gadget driver and close the backing file. */
3444 if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags)) {
3445 usb_gadget_unregister_driver(&fsg_driver);
3446 close_all_backing_files(fsg);
3447 }
3448
3449 /* Let the unbind and cleanup routines know the thread has exited */
3450 complete_and_exit(&fsg->thread_notifier, 0);
3451 }
3452
3453
3454 /*-------------------------------------------------------------------------*/
3455
3456 /* If the next two routines are called while the gadget is registered,
3457 * the caller must own fsg->filesem for writing. */
3458
3459 static int open_backing_file(struct lun *curlun, const char *filename)
3460 {
3461 int ro;
3462 struct file *filp = NULL;
3463 int rc = -EINVAL;
3464 struct inode *inode = NULL;
3465 loff_t size;
3466 loff_t num_sectors;
3467
3468 /* R/W if we can, R/O if we must */
3469 ro = curlun->ro;
3470 if (!ro) {
3471 filp = filp_open(filename, O_RDWR | O_LARGEFILE, 0);
3472 if (-EROFS == PTR_ERR(filp))
3473 ro = 1;
3474 }
3475 if (ro)
3476 filp = filp_open(filename, O_RDONLY | O_LARGEFILE, 0);
3477 if (IS_ERR(filp)) {
3478 LINFO(curlun, "unable to open backing file: %s\n", filename);
3479 return PTR_ERR(filp);
3480 }
3481
3482 if (!(filp->f_mode & FMODE_WRITE))
3483 ro = 1;
3484
3485 if (filp->f_path.dentry)
3486 inode = filp->f_path.dentry->d_inode;
3487 if (inode && S_ISBLK(inode->i_mode)) {
3488 if (bdev_read_only(inode->i_bdev))
3489 ro = 1;
3490 } else if (!inode || !S_ISREG(inode->i_mode)) {
3491 LINFO(curlun, "invalid file type: %s\n", filename);
3492 goto out;
3493 }
3494
3495 /* If we can't read the file, it's no good.
3496 * If we can't write the file, use it read-only. */
3497 if (!filp->f_op || !(filp->f_op->read || filp->f_op->aio_read)) {
3498 LINFO(curlun, "file not readable: %s\n", filename);
3499 goto out;
3500 }
3501 if (!(filp->f_op->write || filp->f_op->aio_write))
3502 ro = 1;
3503
3504 size = i_size_read(inode->i_mapping->host);
3505 if (size < 0) {
3506 LINFO(curlun, "unable to find file size: %s\n", filename);
3507 rc = (int) size;
3508 goto out;
3509 }
3510 num_sectors = size >> 9; // File size in 512-byte sectors
3511 if (num_sectors == 0) {
3512 LINFO(curlun, "file too small: %s\n", filename);
3513 rc = -ETOOSMALL;
3514 goto out;
3515 }
3516
3517 get_file(filp);
3518 curlun->ro = ro;
3519 curlun->filp = filp;
3520 curlun->file_length = size;
3521 curlun->num_sectors = num_sectors;
3522 LDBG(curlun, "open backing file: %s\n", filename);
3523 rc = 0;
3524
3525 out:
3526 filp_close(filp, current->files);
3527 return rc;
3528 }
3529
3530
3531 static void close_backing_file(struct lun *curlun)
3532 {
3533 if (curlun->filp) {
3534 LDBG(curlun, "close backing file\n");
3535 fput(curlun->filp);
3536 curlun->filp = NULL;
3537 }
3538 }
3539
3540 static void close_all_backing_files(struct fsg_dev *fsg)
3541 {
3542 int i;
3543
3544 for (i = 0; i < fsg->nluns; ++i)
3545 close_backing_file(&fsg->luns[i]);
3546 }
3547
3548
3549 static ssize_t show_ro(struct device *dev, struct device_attribute *attr, char *buf)
3550 {
3551 struct lun *curlun = dev_to_lun(dev);
3552
3553 return sprintf(buf, "%d\n", curlun->ro);
3554 }
3555
3556 static ssize_t show_file(struct device *dev, struct device_attribute *attr,
3557 char *buf)
3558 {
3559 struct lun *curlun = dev_to_lun(dev);
3560 struct fsg_dev *fsg = dev_get_drvdata(dev);
3561 char *p;
3562 ssize_t rc;
3563
3564 down_read(&fsg->filesem);
3565 if (backing_file_is_open(curlun)) { // Get the complete pathname
3566 p = d_path(&curlun->filp->f_path, buf, PAGE_SIZE - 1);
3567 if (IS_ERR(p))
3568 rc = PTR_ERR(p);
3569 else {
3570 rc = strlen(p);
3571 memmove(buf, p, rc);
3572 buf[rc] = '\n'; // Add a newline
3573 buf[++rc] = 0;
3574 }
3575 } else { // No file, return 0 bytes
3576 *buf = 0;
3577 rc = 0;
3578 }
3579 up_read(&fsg->filesem);
3580 return rc;
3581 }
3582
3583
3584 static ssize_t store_ro(struct device *dev, struct device_attribute *attr,
3585 const char *buf, size_t count)
3586 {
3587 ssize_t rc = count;
3588 struct lun *curlun = dev_to_lun(dev);
3589 struct fsg_dev *fsg = dev_get_drvdata(dev);
3590 int i;
3591
3592 if (sscanf(buf, "%d", &i) != 1)
3593 return -EINVAL;
3594
3595 /* Allow the write-enable status to change only while the backing file
3596 * is closed. */
3597 down_read(&fsg->filesem);
3598 if (backing_file_is_open(curlun)) {
3599 LDBG(curlun, "read-only status change prevented\n");
3600 rc = -EBUSY;
3601 } else {
3602 curlun->ro = !!i;
3603 LDBG(curlun, "read-only status set to %d\n", curlun->ro);
3604 }
3605 up_read(&fsg->filesem);
3606 return rc;
3607 }
3608
3609 static ssize_t store_file(struct device *dev, struct device_attribute *attr,
3610 const char *buf, size_t count)
3611 {
3612 struct lun *curlun = dev_to_lun(dev);
3613 struct fsg_dev *fsg = dev_get_drvdata(dev);
3614 int rc = 0;
3615
3616 if (curlun->prevent_medium_removal && backing_file_is_open(curlun)) {
3617 LDBG(curlun, "eject attempt prevented\n");
3618 return -EBUSY; // "Door is locked"
3619 }
3620
3621 /* Remove a trailing newline */
3622 if (count > 0 && buf[count-1] == '\n')
3623 ((char *) buf)[count-1] = 0; // Ugh!
3624
3625 /* Eject current medium */
3626 down_write(&fsg->filesem);
3627 if (backing_file_is_open(curlun)) {
3628 close_backing_file(curlun);
3629 curlun->unit_attention_data = SS_MEDIUM_NOT_PRESENT;
3630 }
3631
3632 /* Load new medium */
3633 if (count > 0 && buf[0]) {
3634 rc = open_backing_file(curlun, buf);
3635 if (rc == 0)
3636 curlun->unit_attention_data =
3637 SS_NOT_READY_TO_READY_TRANSITION;
3638 }
3639 up_write(&fsg->filesem);
3640 return (rc < 0 ? rc : count);
3641 }
3642
3643
3644 /* The write permissions and store_xxx pointers are set in fsg_bind() */
3645 static DEVICE_ATTR(ro, 0444, show_ro, NULL);
3646 static DEVICE_ATTR(file, 0444, show_file, NULL);
3647
3648
3649 /*-------------------------------------------------------------------------*/
3650
3651 static void fsg_release(struct kref *ref)
3652 {
3653 struct fsg_dev *fsg = container_of(ref, struct fsg_dev, ref);
3654
3655 kfree(fsg->luns);
3656 kfree(fsg);
3657 }
3658
3659 static void lun_release(struct device *dev)
3660 {
3661 struct fsg_dev *fsg = dev_get_drvdata(dev);
3662
3663 kref_put(&fsg->ref, fsg_release);
3664 }
3665
3666 static void /* __init_or_exit */ fsg_unbind(struct usb_gadget *gadget)
3667 {
3668 struct fsg_dev *fsg = get_gadget_data(gadget);
3669 int i;
3670 struct lun *curlun;
3671 struct usb_request *req = fsg->ep0req;
3672
3673 DBG(fsg, "unbind\n");
3674 clear_bit(REGISTERED, &fsg->atomic_bitflags);
3675
3676 /* Unregister the sysfs attribute files and the LUNs */
3677 for (i = 0; i < fsg->nluns; ++i) {
3678 curlun = &fsg->luns[i];
3679 if (curlun->registered) {
3680 device_remove_file(&curlun->dev, &dev_attr_ro);
3681 device_remove_file(&curlun->dev, &dev_attr_file);
3682 device_unregister(&curlun->dev);
3683 curlun->registered = 0;
3684 }
3685 }
3686
3687 /* If the thread isn't already dead, tell it to exit now */
3688 if (fsg->state != FSG_STATE_TERMINATED) {
3689 raise_exception(fsg, FSG_STATE_EXIT);
3690 wait_for_completion(&fsg->thread_notifier);
3691
3692 /* The cleanup routine waits for this completion also */
3693 complete(&fsg->thread_notifier);
3694 }
3695
3696 /* Free the data buffers */
3697 for (i = 0; i < NUM_BUFFERS; ++i)
3698 kfree(fsg->buffhds[i].buf);
3699
3700 /* Free the request and buffer for endpoint 0 */
3701 if (req) {
3702 kfree(req->buf);
3703 usb_ep_free_request(fsg->ep0, req);
3704 }
3705
3706 set_gadget_data(gadget, NULL);
3707 }
3708
3709
3710 static int __init check_parameters(struct fsg_dev *fsg)
3711 {
3712 int prot;
3713 int gcnum;
3714
3715 /* Store the default values */
3716 mod_data.transport_type = USB_PR_BULK;
3717 mod_data.transport_name = "Bulk-only";
3718 mod_data.protocol_type = USB_SC_SCSI;
3719 mod_data.protocol_name = "Transparent SCSI";
3720
3721 if (gadget_is_sh(fsg->gadget))
3722 mod_data.can_stall = 0;
3723
3724 if (mod_data.release == 0xffff) { // Parameter wasn't set
3725 /* The sa1100 controller is not supported */
3726 if (gadget_is_sa1100(fsg->gadget))
3727 gcnum = -1;
3728 else
3729 gcnum = usb_gadget_controller_number(fsg->gadget);
3730 if (gcnum >= 0)
3731 mod_data.release = 0x0300 + gcnum;
3732 else {
3733 WARN(fsg, "controller '%s' not recognized\n",
3734 fsg->gadget->name);
3735 mod_data.release = 0x0399;
3736 }
3737 }
3738
3739 prot = simple_strtol(mod_data.protocol_parm, NULL, 0);
3740
3741 #ifdef CONFIG_USB_FILE_STORAGE_TEST
3742 if (strnicmp(mod_data.transport_parm, "BBB", 10) == 0) {
3743 ; // Use default setting
3744 } else if (strnicmp(mod_data.transport_parm, "CB", 10) == 0) {
3745 mod_data.transport_type = USB_PR_CB;
3746 mod_data.transport_name = "Control-Bulk";
3747 } else if (strnicmp(mod_data.transport_parm, "CBI", 10) == 0) {
3748 mod_data.transport_type = USB_PR_CBI;
3749 mod_data.transport_name = "Control-Bulk-Interrupt";
3750 } else {
3751 ERROR(fsg, "invalid transport: %s\n", mod_data.transport_parm);
3752 return -EINVAL;
3753 }
3754
3755 if (strnicmp(mod_data.protocol_parm, "SCSI", 10) == 0 ||
3756 prot == USB_SC_SCSI) {
3757 ; // Use default setting
3758 } else if (strnicmp(mod_data.protocol_parm, "RBC", 10) == 0 ||
3759 prot == USB_SC_RBC) {
3760 mod_data.protocol_type = USB_SC_RBC;
3761 mod_data.protocol_name = "RBC";
3762 } else if (strnicmp(mod_data.protocol_parm, "8020", 4) == 0 ||
3763 strnicmp(mod_data.protocol_parm, "ATAPI", 10) == 0 ||
3764 prot == USB_SC_8020) {
3765 mod_data.protocol_type = USB_SC_8020;
3766 mod_data.protocol_name = "8020i (ATAPI)";
3767 } else if (strnicmp(mod_data.protocol_parm, "QIC", 3) == 0 ||
3768 prot == USB_SC_QIC) {
3769 mod_data.protocol_type = USB_SC_QIC;
3770 mod_data.protocol_name = "QIC-157";
3771 } else if (strnicmp(mod_data.protocol_parm, "UFI", 10) == 0 ||
3772 prot == USB_SC_UFI) {
3773 mod_data.protocol_type = USB_SC_UFI;
3774 mod_data.protocol_name = "UFI";
3775 } else if (strnicmp(mod_data.protocol_parm, "8070", 4) == 0 ||
3776 prot == USB_SC_8070) {
3777 mod_data.protocol_type = USB_SC_8070;
3778 mod_data.protocol_name = "8070i";
3779 } else {
3780 ERROR(fsg, "invalid protocol: %s\n", mod_data.protocol_parm);
3781 return -EINVAL;
3782 }
3783
3784 mod_data.buflen &= PAGE_CACHE_MASK;
3785 if (mod_data.buflen <= 0) {
3786 ERROR(fsg, "invalid buflen\n");
3787 return -ETOOSMALL;
3788 }
3789 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
3790
3791 return 0;
3792 }
3793
3794
3795 static int __init fsg_bind(struct usb_gadget *gadget)
3796 {
3797 struct fsg_dev *fsg = the_fsg;
3798 int rc;
3799 int i;
3800 struct lun *curlun;
3801 struct usb_ep *ep;
3802 struct usb_request *req;
3803 char *pathbuf, *p;
3804
3805 fsg->gadget = gadget;
3806 set_gadget_data(gadget, fsg);
3807 fsg->ep0 = gadget->ep0;
3808 fsg->ep0->driver_data = fsg;
3809
3810 if ((rc = check_parameters(fsg)) != 0)
3811 goto out;
3812
3813 if (mod_data.removable) { // Enable the store_xxx attributes
3814 dev_attr_ro.attr.mode = dev_attr_file.attr.mode = 0644;
3815 dev_attr_ro.store = store_ro;
3816 dev_attr_file.store = store_file;
3817 }
3818
3819 /* Find out how many LUNs there should be */
3820 i = mod_data.nluns;
3821 if (i == 0)
3822 i = max(mod_data.num_filenames, 1u);
3823 if (i > MAX_LUNS) {
3824 ERROR(fsg, "invalid number of LUNs: %d\n", i);
3825 rc = -EINVAL;
3826 goto out;
3827 }
3828
3829 /* Create the LUNs, open their backing files, and register the
3830 * LUN devices in sysfs. */
3831 fsg->luns = kzalloc(i * sizeof(struct lun), GFP_KERNEL);
3832 if (!fsg->luns) {
3833 rc = -ENOMEM;
3834 goto out;
3835 }
3836 fsg->nluns = i;
3837
3838 for (i = 0; i < fsg->nluns; ++i) {
3839 curlun = &fsg->luns[i];
3840 curlun->ro = mod_data.ro[i];
3841 curlun->dev.release = lun_release;
3842 curlun->dev.parent = &gadget->dev;
3843 curlun->dev.driver = &fsg_driver.driver;
3844 dev_set_drvdata(&curlun->dev, fsg);
3845 snprintf(curlun->dev.bus_id, BUS_ID_SIZE,
3846 "%s-lun%d", gadget->dev.bus_id, i);
3847
3848 if ((rc = device_register(&curlun->dev)) != 0) {
3849 INFO(fsg, "failed to register LUN%d: %d\n", i, rc);
3850 goto out;
3851 }
3852 if ((rc = device_create_file(&curlun->dev,
3853 &dev_attr_ro)) != 0 ||
3854 (rc = device_create_file(&curlun->dev,
3855 &dev_attr_file)) != 0) {
3856 device_unregister(&curlun->dev);
3857 goto out;
3858 }
3859 curlun->registered = 1;
3860 kref_get(&fsg->ref);
3861
3862 if (mod_data.file[i] && *mod_data.file[i]) {
3863 if ((rc = open_backing_file(curlun,
3864 mod_data.file[i])) != 0)
3865 goto out;
3866 } else if (!mod_data.removable) {
3867 ERROR(fsg, "no file given for LUN%d\n", i);
3868 rc = -EINVAL;
3869 goto out;
3870 }
3871 }
3872
3873 /* Find all the endpoints we will use */
3874 usb_ep_autoconfig_reset(gadget);
3875 ep = usb_ep_autoconfig(gadget, &fs_bulk_in_desc);
3876 if (!ep)
3877 goto autoconf_fail;
3878 ep->driver_data = fsg; // claim the endpoint
3879 fsg->bulk_in = ep;
3880
3881 ep = usb_ep_autoconfig(gadget, &fs_bulk_out_desc);
3882 if (!ep)
3883 goto autoconf_fail;
3884 ep->driver_data = fsg; // claim the endpoint
3885 fsg->bulk_out = ep;
3886
3887 if (transport_is_cbi()) {
3888 ep = usb_ep_autoconfig(gadget, &fs_intr_in_desc);
3889 if (!ep)
3890 goto autoconf_fail;
3891 ep->driver_data = fsg; // claim the endpoint
3892 fsg->intr_in = ep;
3893 }
3894
3895 /* Fix up the descriptors */
3896 device_desc.bMaxPacketSize0 = fsg->ep0->maxpacket;
3897 device_desc.idVendor = cpu_to_le16(mod_data.vendor);
3898 device_desc.idProduct = cpu_to_le16(mod_data.product);
3899 device_desc.bcdDevice = cpu_to_le16(mod_data.release);
3900
3901 i = (transport_is_cbi() ? 3 : 2); // Number of endpoints
3902 intf_desc.bNumEndpoints = i;
3903 intf_desc.bInterfaceSubClass = mod_data.protocol_type;
3904 intf_desc.bInterfaceProtocol = mod_data.transport_type;
3905 fs_function[i + FS_FUNCTION_PRE_EP_ENTRIES] = NULL;
3906
3907 if (gadget_is_dualspeed(gadget)) {
3908 hs_function[i + HS_FUNCTION_PRE_EP_ENTRIES] = NULL;
3909
3910 /* Assume ep0 uses the same maxpacket value for both speeds */
3911 dev_qualifier.bMaxPacketSize0 = fsg->ep0->maxpacket;
3912
3913 /* Assume endpoint addresses are the same for both speeds */
3914 hs_bulk_in_desc.bEndpointAddress =
3915 fs_bulk_in_desc.bEndpointAddress;
3916 hs_bulk_out_desc.bEndpointAddress =
3917 fs_bulk_out_desc.bEndpointAddress;
3918 hs_intr_in_desc.bEndpointAddress =
3919 fs_intr_in_desc.bEndpointAddress;
3920 }
3921
3922 if (gadget_is_otg(gadget))
3923 otg_desc.bmAttributes |= USB_OTG_HNP;
3924
3925 rc = -ENOMEM;
3926
3927 /* Allocate the request and buffer for endpoint 0 */
3928 fsg->ep0req = req = usb_ep_alloc_request(fsg->ep0, GFP_KERNEL);
3929 if (!req)
3930 goto out;
3931 req->buf = kmalloc(EP0_BUFSIZE, GFP_KERNEL);
3932 if (!req->buf)
3933 goto out;
3934 req->complete = ep0_complete;
3935
3936 /* Allocate the data buffers */
3937 for (i = 0; i < NUM_BUFFERS; ++i) {
3938 struct fsg_buffhd *bh = &fsg->buffhds[i];
3939
3940 /* Allocate for the bulk-in endpoint. We assume that
3941 * the buffer will also work with the bulk-out (and
3942 * interrupt-in) endpoint. */
3943 bh->buf = kmalloc(mod_data.buflen, GFP_KERNEL);
3944 if (!bh->buf)
3945 goto out;
3946 bh->next = bh + 1;
3947 }
3948 fsg->buffhds[NUM_BUFFERS - 1].next = &fsg->buffhds[0];
3949
3950 /* This should reflect the actual gadget power source */
3951 usb_gadget_set_selfpowered(gadget);
3952
3953 snprintf(manufacturer, sizeof manufacturer, "%s %s with %s",
3954 init_utsname()->sysname, init_utsname()->release,
3955 gadget->name);
3956
3957 /* On a real device, serial[] would be loaded from permanent
3958 * storage. We just encode it from the driver version string. */
3959 for (i = 0; i < sizeof(serial) - 2; i += 2) {
3960 unsigned char c = DRIVER_VERSION[i / 2];
3961
3962 if (!c)
3963 break;
3964 sprintf(&serial[i], "%02X", c);
3965 }
3966
3967 fsg->thread_task = kthread_create(fsg_main_thread, fsg,
3968 "file-storage-gadget");
3969 if (IS_ERR(fsg->thread_task)) {
3970 rc = PTR_ERR(fsg->thread_task);
3971 goto out;
3972 }
3973
3974 INFO(fsg, DRIVER_DESC ", version: " DRIVER_VERSION "\n");
3975 INFO(fsg, "Number of LUNs=%d\n", fsg->nluns);
3976
3977 pathbuf = kmalloc(PATH_MAX, GFP_KERNEL);
3978 for (i = 0; i < fsg->nluns; ++i) {
3979 curlun = &fsg->luns[i];
3980 if (backing_file_is_open(curlun)) {
3981 p = NULL;
3982 if (pathbuf) {
3983 p = d_path(&curlun->filp->f_path,
3984 pathbuf, PATH_MAX);
3985 if (IS_ERR(p))
3986 p = NULL;
3987 }
3988 LINFO(curlun, "ro=%d, file: %s\n",
3989 curlun->ro, (p ? p : "(error)"));
3990 }
3991 }
3992 kfree(pathbuf);
3993
3994 DBG(fsg, "transport=%s (x%02x)\n",
3995 mod_data.transport_name, mod_data.transport_type);
3996 DBG(fsg, "protocol=%s (x%02x)\n",
3997 mod_data.protocol_name, mod_data.protocol_type);
3998 DBG(fsg, "VendorID=x%04x, ProductID=x%04x, Release=x%04x\n",
3999 mod_data.vendor, mod_data.product, mod_data.release);
4000 DBG(fsg, "removable=%d, stall=%d, buflen=%u\n",
4001 mod_data.removable, mod_data.can_stall,
4002 mod_data.buflen);
4003 DBG(fsg, "I/O thread pid: %d\n", task_pid_nr(fsg->thread_task));
4004
4005 set_bit(REGISTERED, &fsg->atomic_bitflags);
4006
4007 /* Tell the thread to start working */
4008 wake_up_process(fsg->thread_task);
4009 return 0;
4010
4011 autoconf_fail:
4012 ERROR(fsg, "unable to autoconfigure all endpoints\n");
4013 rc = -ENOTSUPP;
4014
4015 out:
4016 fsg->state = FSG_STATE_TERMINATED; // The thread is dead
4017 fsg_unbind(gadget);
4018 close_all_backing_files(fsg);
4019 return rc;
4020 }
4021
4022
4023 /*-------------------------------------------------------------------------*/
4024
4025 static void fsg_suspend(struct usb_gadget *gadget)
4026 {
4027 struct fsg_dev *fsg = get_gadget_data(gadget);
4028
4029 DBG(fsg, "suspend\n");
4030 set_bit(SUSPENDED, &fsg->atomic_bitflags);
4031 }
4032
4033 static void fsg_resume(struct usb_gadget *gadget)
4034 {
4035 struct fsg_dev *fsg = get_gadget_data(gadget);
4036
4037 DBG(fsg, "resume\n");
4038 clear_bit(SUSPENDED, &fsg->atomic_bitflags);
4039 }
4040
4041
4042 /*-------------------------------------------------------------------------*/
4043
4044 static struct usb_gadget_driver fsg_driver = {
4045 #ifdef CONFIG_USB_GADGET_DUALSPEED
4046 .speed = USB_SPEED_HIGH,
4047 #else
4048 .speed = USB_SPEED_FULL,
4049 #endif
4050 .function = (char *) longname,
4051 .bind = fsg_bind,
4052 .unbind = fsg_unbind,
4053 .disconnect = fsg_disconnect,
4054 .setup = fsg_setup,
4055 .suspend = fsg_suspend,
4056 .resume = fsg_resume,
4057
4058 .driver = {
4059 .name = (char *) shortname,
4060 .owner = THIS_MODULE,
4061 // .release = ...
4062 // .suspend = ...
4063 // .resume = ...
4064 },
4065 };
4066
4067
4068 static int __init fsg_alloc(void)
4069 {
4070 struct fsg_dev *fsg;
4071
4072 fsg = kzalloc(sizeof *fsg, GFP_KERNEL);
4073 if (!fsg)
4074 return -ENOMEM;
4075 spin_lock_init(&fsg->lock);
4076 init_rwsem(&fsg->filesem);
4077 kref_init(&fsg->ref);
4078 init_completion(&fsg->thread_notifier);
4079
4080 the_fsg = fsg;
4081 return 0;
4082 }
4083
4084
4085 static int __init fsg_init(void)
4086 {
4087 int rc;
4088 struct fsg_dev *fsg;
4089
4090 if ((rc = fsg_alloc()) != 0)
4091 return rc;
4092 fsg = the_fsg;
4093 if ((rc = usb_gadget_register_driver(&fsg_driver)) != 0)
4094 kref_put(&fsg->ref, fsg_release);
4095 return rc;
4096 }
4097 module_init(fsg_init);
4098
4099
4100 static void __exit fsg_cleanup(void)
4101 {
4102 struct fsg_dev *fsg = the_fsg;
4103
4104 /* Unregister the driver iff the thread hasn't already done so */
4105 if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags))
4106 usb_gadget_unregister_driver(&fsg_driver);
4107
4108 /* Wait for the thread to finish up */
4109 wait_for_completion(&fsg->thread_notifier);
4110
4111 close_all_backing_files(fsg);
4112 kref_put(&fsg->ref, fsg_release);
4113 }
4114 module_exit(fsg_cleanup);
Linux with added FPC-III support