arch/blackfin/mach-bf537/boards/dnp5370.c

   1 /*
   2  * This is the configuration for SSV Dil/NetPC DNP/5370 board.
   3  *
   4  * DIL module:         http://www.dilnetpc.com/dnp0086.htm
   5  * SK28 (starter kit): http://www.dilnetpc.com/dnp0088.htm
   6  *
   7  * Copyright 2010 3ality Digital Systems
   8  * Copyright 2005 National ICT Australia (NICTA)
   9  * Copyright 2004-2006 Analog Devices Inc.
  10  *
  11  * Licensed under the GPL-2 or later.
  12  */
  13
  14 #include <linux/device.h>
  15 #include <linux/export.h>
  16 #include <linux/kernel.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/io.h>
  19 #include <linux/mtd/mtd.h>
  20 #include <linux/mtd/nand.h>
  21 #include <linux/mtd/partitions.h>
  22 #include <linux/mtd/plat-ram.h>
  23 #include <linux/mtd/physmap.h>
  24 #include <linux/spi/spi.h>
  25 #include <linux/spi/flash.h>
  26 #include <linux/irq.h>
  27 #include <linux/interrupt.h>
  28 #include <linux/i2c.h>
  29 #include <linux/spi/mmc_spi.h>
  30 #include <linux/phy.h>
  31 #include <asm/dma.h>
  32 #include <asm/bfin5xx_spi.h>
  33 #include <asm/reboot.h>
  34 #include <asm/portmux.h>
  35 #include <asm/dpmc.h>
  36
  37 /*
  38  * Name the Board for the /proc/cpuinfo
  39  */
  40 const char bfin_board_name[] = "DNP/5370";
  41 #define FLASH_MAC               0x202f0000
  42 #define CONFIG_MTD_PHYSMAP_LEN  0x300000
  43
  44 #if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
  45 static struct platform_device rtc_device = {
  46         .name = "rtc-bfin",
  47         .id   = -1,
  48 };
  49 #endif
  50
  51 #if IS_ENABLED(CONFIG_BFIN_MAC)
  52 #include <linux/bfin_mac.h>
  53 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
  54
  55 static struct bfin_phydev_platform_data bfin_phydev_data[] = {
  56         {
  57                 .addr = 1,
  58                 .irq = PHY_POLL, /* IRQ_MAC_PHYINT */
  59         },
  60 };
  61
  62 static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
  63         .phydev_number   = 1,
  64         .phydev_data     = bfin_phydev_data,
  65         .phy_mode        = PHY_INTERFACE_MODE_RMII,
  66         .mac_peripherals = bfin_mac_peripherals,
  67 };
  68
  69 static struct platform_device bfin_mii_bus = {
  70         .name = "bfin_mii_bus",
  71         .dev = {
  72                 .platform_data = &bfin_mii_bus_data,
  73         }
  74 };
  75
  76 static struct platform_device bfin_mac_device = {
  77         .name = "bfin_mac",
  78         .dev = {
  79                 .platform_data = &bfin_mii_bus,
  80         }
  81 };
  82 #endif
  83
  84 #if IS_ENABLED(CONFIG_MTD_PHYSMAP)
  85 static struct mtd_partition asmb_flash_partitions[] = {
  86         {
  87                 .name       = "bootloader(nor)",
  88                 .size       = 0x30000,
  89                 .offset     = 0,
  90         }, {
  91                 .name       = "linux kernel and rootfs(nor)",
  92                 .size       = 0x300000 - 0x30000 - 0x10000,
  93                 .offset     = MTDPART_OFS_APPEND,
  94         }, {
  95                 .name       = "MAC address(nor)",
  96                 .size       = 0x10000,
  97                 .offset     = MTDPART_OFS_APPEND,
  98                 .mask_flags = MTD_WRITEABLE,
  99         }
 100 };
 101
 102 static struct physmap_flash_data asmb_flash_data = {
 103         .width      = 1,
 104         .parts      = asmb_flash_partitions,
 105         .nr_parts   = ARRAY_SIZE(asmb_flash_partitions),
 106 };
 107
 108 static struct resource asmb_flash_resource = {
 109         .start = 0x20000000,
 110         .end   = 0x202fffff,
 111         .flags = IORESOURCE_MEM,
 112 };
 113
 114 /* 4 MB NOR flash attached to async memory banks 0-2,
 115  * therefore only 3 MB visible.
 116  */
 117 static struct platform_device asmb_flash_device = {
 118         .name     = "physmap-flash",
 119         .id       = 0,
 120         .dev = {
 121                 .platform_data = &asmb_flash_data,
 122         },
 123         .num_resources = 1,
 124         .resource      = &asmb_flash_resource,
 125 };
 126 #endif
 127
 128 #if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 129
 130 #if IS_ENABLED(CONFIG_MMC_SPI)
 131
 132 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 133         .enable_dma    = 0,      /* use no dma transfer with this chip*/
 134 };
 135
 136 #endif
 137
 138 #if IS_ENABLED(CONFIG_MTD_DATAFLASH)
 139 /* This mapping is for at45db642 it has 1056 page size,
 140  * partition size and offset should be page aligned
 141  */
 142 static struct mtd_partition bfin_spi_dataflash_partitions[] = {
 143         {
 144                 .name   = "JFFS2 dataflash(nor)",
 145 #ifdef CONFIG_MTD_PAGESIZE_1024
 146                 .offset = 0x40000,
 147                 .size   = 0x7C0000,
 148 #else
 149                 .offset = 0x0,
 150                 .size   = 0x840000,
 151 #endif
 152         }
 153 };
 154
 155 static struct flash_platform_data bfin_spi_dataflash_data = {
 156         .name     = "mtd_dataflash",
 157         .parts    = bfin_spi_dataflash_partitions,
 158         .nr_parts = ARRAY_SIZE(bfin_spi_dataflash_partitions),
 159         .type     = "mtd_dataflash",
 160 };
 161
 162 static struct bfin5xx_spi_chip spi_dataflash_chip_info = {
 163         .enable_dma    = 0,      /* use no dma transfer with this chip*/
 164 };
 165 #endif
 166
 167 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 168 /* SD/MMC card reader at SPI bus */
 169 #if IS_ENABLED(CONFIG_MMC_SPI)
 170         {
 171                 .modalias        = "mmc_spi",
 172                 .max_speed_hz    = 20000000,
 173                 .bus_num         = 0,
 174                 .chip_select     = 1,
 175                 .controller_data = &mmc_spi_chip_info,
 176                 .mode            = SPI_MODE_3,
 177         },
 178 #endif
 179
 180 /* 8 Megabyte Atmel NOR flash chip at SPI bus */
 181 #if IS_ENABLED(CONFIG_MTD_DATAFLASH)
 182         {
 183         .modalias        = "mtd_dataflash",
 184         .max_speed_hz    = 16700000,
 185         .bus_num         = 0,
 186         .chip_select     = 2,
 187         .platform_data   = &bfin_spi_dataflash_data,
 188         .controller_data = &spi_dataflash_chip_info,
 189         .mode            = SPI_MODE_3, /* SPI_CPHA and SPI_CPOL */
 190         },
 191 #endif
 192 };
 193
 194 /* SPI controller data */
 195 /* SPI (0) */
 196 static struct resource bfin_spi0_resource[] = {
 197         [0] = {
 198                 .start = SPI0_REGBASE,
 199                 .end   = SPI0_REGBASE + 0xFF,
 200                 .flags = IORESOURCE_MEM,
 201         },
 202         [1] = {
 203                 .start = CH_SPI,
 204                 .end   = CH_SPI,
 205                 .flags = IORESOURCE_DMA,
 206         },
 207         [2] = {
 208                 .start = IRQ_SPI,
 209                 .end   = IRQ_SPI,
 210                 .flags = IORESOURCE_IRQ,
 211         },
 212 };
 213
 214 static struct bfin5xx_spi_master spi_bfin_master_info = {
 215         .num_chipselect = 8,
 216         .enable_dma     = 1,  /* master has the ability to do dma transfer */
 217         .pin_req        = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 218 };
 219
 220 static struct platform_device spi_bfin_master_device = {
 221         .name          = "bfin-spi",
 222         .id            = 0, /* Bus number */
 223         .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 224         .resource      = bfin_spi0_resource,
 225         .dev           = {
 226                 .platform_data = &spi_bfin_master_info, /* Passed to driver */
 227         },
 228 };
 229 #endif
 230
 231 #if IS_ENABLED(CONFIG_SERIAL_BFIN)
 232 #ifdef CONFIG_SERIAL_BFIN_UART0
 233 static struct resource bfin_uart0_resources[] = {
 234         {
 235                 .start = UART0_THR,
 236                 .end = UART0_GCTL+2,
 237                 .flags = IORESOURCE_MEM,
 238         },
 239         {
 240                 .start = IRQ_UART0_TX,
 241                 .end = IRQ_UART0_TX,
 242                 .flags = IORESOURCE_IRQ,
 243         },
 244         {
 245                 .start = IRQ_UART0_RX,
 246                 .end = IRQ_UART0_RX,
 247                 .flags = IORESOURCE_IRQ,
 248         },
 249         {
 250                 .start = IRQ_UART0_ERROR,
 251                 .end = IRQ_UART0_ERROR,
 252                 .flags = IORESOURCE_IRQ,
 253         },
 254         {
 255                 .start = CH_UART0_TX,
 256                 .end = CH_UART0_TX,
 257                 .flags = IORESOURCE_DMA,
 258         },
 259         {
 260                 .start = CH_UART0_RX,
 261                 .end = CH_UART0_RX,
 262                 .flags = IORESOURCE_DMA,
 263         },
 264 };
 265
 266 static unsigned short bfin_uart0_peripherals[] = {
 267         P_UART0_TX, P_UART0_RX, 0
 268 };
 269
 270 static struct platform_device bfin_uart0_device = {
 271         .name = "bfin-uart",
 272         .id = 0,
 273         .num_resources = ARRAY_SIZE(bfin_uart0_resources),
 274         .resource = bfin_uart0_resources,
 275         .dev = {
 276                 .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
 277         },
 278 };
 279 #endif
 280
 281 #ifdef CONFIG_SERIAL_BFIN_UART1
 282 static struct resource bfin_uart1_resources[] = {
 283         {
 284                 .start = UART1_THR,
 285                 .end   = UART1_GCTL+2,
 286                 .flags = IORESOURCE_MEM,
 287         },
 288         {
 289                 .start = IRQ_UART1_TX,
 290                 .end   = IRQ_UART1_TX,
 291                 .flags = IORESOURCE_IRQ,
 292         },
 293         {
 294                 .start = IRQ_UART1_RX,
 295                 .end   = IRQ_UART1_RX,
 296                 .flags = IORESOURCE_IRQ,
 297         },
 298         {
 299                 .start = IRQ_UART1_ERROR,
 300                 .end   = IRQ_UART1_ERROR,
 301                 .flags = IORESOURCE_IRQ,
 302         },
 303         {
 304                 .start = CH_UART1_TX,
 305                 .end   = CH_UART1_TX,
 306                 .flags = IORESOURCE_DMA,
 307         },
 308         {
 309                 .start = CH_UART1_RX,
 310                 .end   = CH_UART1_RX,
 311                 .flags = IORESOURCE_DMA,
 312         },
 313 };
 314
 315 static unsigned short bfin_uart1_peripherals[] = {
 316         P_UART1_TX, P_UART1_RX, 0
 317 };
 318
 319 static struct platform_device bfin_uart1_device = {
 320         .name          = "bfin-uart",
 321         .id            = 1,
 322         .num_resources = ARRAY_SIZE(bfin_uart1_resources),
 323         .resource      = bfin_uart1_resources,
 324         .dev = {
 325                 .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
 326         },
 327 };
 328 #endif
 329 #endif
 330
 331 #if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 332 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 333
 334 static struct resource bfin_twi0_resource[] = {
 335         [0] = {
 336                 .start = TWI0_REGBASE,
 337                 .end   = TWI0_REGBASE + 0xff,
 338                 .flags = IORESOURCE_MEM,
 339         },
 340         [1] = {
 341                 .start = IRQ_TWI,
 342                 .end   = IRQ_TWI,
 343                 .flags = IORESOURCE_IRQ,
 344         },
 345 };
 346
 347 static struct platform_device i2c_bfin_twi_device = {
 348         .name          = "i2c-bfin-twi",
 349         .id            = 0,
 350         .num_resources = ARRAY_SIZE(bfin_twi0_resource),
 351         .resource      = bfin_twi0_resource,
 352         .dev = {
 353                 .platform_data = &bfin_twi0_pins,
 354         },
 355 };
 356 #endif
 357
 358 static struct platform_device *dnp5370_devices[] __initdata = {
 359
 360 #if IS_ENABLED(CONFIG_SERIAL_BFIN)
 361 #ifdef CONFIG_SERIAL_BFIN_UART0
 362         &bfin_uart0_device,
 363 #endif
 364 #ifdef CONFIG_SERIAL_BFIN_UART1
 365         &bfin_uart1_device,
 366 #endif
 367 #endif
 368
 369 #if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 370         &asmb_flash_device,
 371 #endif
 372
 373 #if IS_ENABLED(CONFIG_BFIN_MAC)
 374         &bfin_mii_bus,
 375         &bfin_mac_device,
 376 #endif
 377
 378 #if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 379         &spi_bfin_master_device,
 380 #endif
 381
 382 #if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 383         &i2c_bfin_twi_device,
 384 #endif
 385
 386 #if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 387         &rtc_device,
 388 #endif
 389
 390 };
 391
 392 static int __init dnp5370_init(void)
 393 {
 394         printk(KERN_INFO "DNP/5370: registering device resources\n");
 395         platform_add_devices(dnp5370_devices, ARRAY_SIZE(dnp5370_devices));
 396         printk(KERN_INFO "DNP/5370: registering %zu SPI slave devices\n",
 397                ARRAY_SIZE(bfin_spi_board_info));
 398         spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 399         printk(KERN_INFO "DNP/5370: MAC %pM\n", (void *)FLASH_MAC);
 400         return 0;
 401 }
 402 arch_initcall(dnp5370_init);
 403
 404 /*
 405  * Currently the MAC address is saved in Flash by U-Boot
 406  */
 407 int bfin_get_ether_addr(char *addr)
 408 {
 409         *(u32 *)(&(addr[0])) = bfin_read32(FLASH_MAC);
 410         *(u16 *)(&(addr[4])) = bfin_read16(FLASH_MAC + 4);
 411         return 0;
 412 }
 413 EXPORT_SYMBOL(bfin_get_ether_addr);