4 * Copyright(c) 2016 Broadcom. All rights reserved.
6 * Redistribution and use in source and binary forms, with or without
7 * modification, are permitted provided that the following conditions
10 * * Redistributions of source code must retain the above copyright
11 * notice, this list of conditions and the following disclaimer.
12 * * Redistributions in binary form must reproduce the above copyright
13 * notice, this list of conditions and the following disclaimer in
14 * the documentation and/or other materials provided with the
16 * * Neither the name of Broadcom Corporation nor the names of its
17 * contributors may be used to endorse or promote products derived
18 * from this software without specific prior written permission.
20 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
21 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
22 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
23 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
24 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
25 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
26 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
27 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
28 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
29 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
35 #include "bcm-nsp.dtsi"
36 #include <dt-bindings/gpio/gpio.h>
39 model = "NorthStar Plus SVK (BCM958625HR)";
40 compatible = "brcm,bcm58625", "brcm,nsp";
43 stdout-path = "serial0:115200n8";
47 device_type = "memory";
48 reg = <0x60000000 0x20000000>;
52 compatible = "gpio-restart";
53 gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
58 /* Hardware I2C block cannot do more than 63 bytes per transfer,
59 * which would prevent reading from a SFP's EEPROM (256 byte).
62 compatible = "i2c-gpio";
63 sda-gpios = <&gpioa 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
64 scl-gpios = <&gpioa 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
68 compatible = "sff,sfp";
70 mod-def0-gpios = <&gpioa 28 GPIO_ACTIVE_LOW>;
71 los-gpios = <&gpioa 24 GPIO_ACTIVE_HIGH>;
72 tx-fault-gpios = <&gpioa 30 GPIO_ACTIVE_HIGH>;
73 tx-disable-gpios = <&gpioa 26 GPIO_ACTIVE_HIGH>;
95 compatible = "brcm,nandcs";
102 nand-ecc-strength = <24>;
103 nand-ecc-step-size = <1024>;
105 brcm,nand-oob-sector-size = <27>;
109 reg = <0x00000000 0x00200000>;
114 reg = <0x00200000 0x00400000>;
118 reg = <0x00600000 0x00a00000>;
122 reg = <0x01000000 0x03000000>;
126 reg = <0x04000000 0x3c000000>;
144 pinctrl-names = "default";
145 pinctrl-0 = <&nand_sel>;
155 #address-cells = <1>;
157 compatible = "m25p80";
159 spi-max-frequency = <12500000>;
166 reg = <0x00000000 0x000a0000>;
171 reg = <0x000a0000 0x00060000>;
176 reg = <0x00100000 0x00600000>;
181 reg = <0x00700000 0x01900000>;
195 compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
199 #address-cells = <1>;
232 managed = "in-band-status";